Fantic Motor Fantic 50 Series Manuale utente

2

AVVERTENZA

Si raccomanda, dopo le prime ore di utilizzo, di

controllare tutti i serraggi con particolare atten-

zione a:

A Pinza freno anteriore / posteriore

B Perni ruota

C Corona

D Bulloneria motore

E Bulloneria ammortizzatore

F Raggi ruota

G Telaietto posteriore

Il veicolo è dotato di impianto di scarico cataliti-

co (omologato Euro4) che a motore acceso può

raggiungere elevate temperature.

Evitare asso-

lutamente il contatto con parti del corpo, in-

dumenti, materiali inﬁammabili, pericolo di

ustioni!

AVVERTENZA

In caso di interventi da eseguire sulla moto rivo-

legersi alla catena di assistenza autorizzata FAN-

TIC MOTOR.

Le informazioni tecniche e speciﬁche per la ma-

nutenzione contenute in questa pubblicazione

erano corrette al momento di andare in stampa.

La FANTIC MOTOR

si riserva il diritto di modiﬁ-

care, in qualsiasi momento e senza preavviso, le

speciﬁche, i dati di progettazione e le attrezzatu-

re necessarie. Questa pubblicazione o parte di

essa, non può essere nè ridotta nè tradotta sen-

za la sua approvazione. La FANTIC MOTOR

non

si assume alcuna responsabilità per eventuali erro-

ri ed omissioni. Tutti i diritti sono riservati.

WARNING

It is recommended, after the ﬁrst hours of use,

to check all the torques with particular attention

to:

A Front / Rear brake caliper

B Wheels axle

C Rear sprocket

D Engine bolts

E Rear suspension mounting nuts

F Wheels spokes

G Rear frame

The vehicle is equipped by catalytic exhaust

(accredited Euro4) that can catch up high tem-

peratures.

Absolutely avoid the contact with

body parts, clothes inflammable materials !

WARNING

If necessary consult a FANTIC MOTOR

dealer.

The technical information and speciﬁcations for

maintenance contained in this handbook were

correct at the time of going to press. FANTIC

MOTOR

reserves the right to change the speciﬁ-

cations, design data and necessary equipment at

any time without notice. No part of this publica-

tion may be abridged or translated without the

manufacturer’s approval. FANTIC MOTOR

can-

not be held liable for any errors or omissions. All

rights reserved.

RECOMMANDATION

Il est recommandé, après les premières heures

d’utilisation, de contrôler tous les serrages en

faisant très attention à :

A Pince de frein avant / arrière

B Axes de roue

C Couronne

D Boulonnerie du moteur

E Boulonnerie de l’amortisseur

F Rayons de roue

G Petit châssis arrière

Le véhicule est doté d’un système d’échappe-

ment catalytique (homologué Euro4) qui avec le

moteur allumé peut atteindre des températures

élevées.

Éviter absolument tout contact avec

des parties du corps, des vêtements, des ma-

tériaux inﬂammables, à cause des risques de

brûlures !

RECOMMANDATION

En cas d’interventions à eectuer sur la moto,

s’adresser à la chaîne d’assistance agréée

FAN-

TIC MOTOR.

Les informations techniques et spéciﬁques pour

l’entretien contenues dans ce document étaient

correctes avant d’être imprimées. La Sté

FANTIC

MOTOR

se réserve le droit de modiﬁer, à tout

moment et sans préavis, les spéciﬁcations, les

données de conception et les équipements né-

cessaires. Ce document ou partie de celui-ci ne

peut être ni réduit, ni traduit sans son approba-

tion. La Sté FANTIC MOTOR

décline toute respon-

sabilité pour toute erreur ou omission. Tous les

droits sont réservés.

46

CONTENTS

Introduction ..........................................................47

Manufacturer’s data and edition ...............47

General contents and consultation ..........47

Identiﬁcation .....................................................47

Symbols used in the handbook.................48

Basic safety rules

...............................................49

Behaviour and driving ...................................49

Clothing ...............................................................49

Accessories .........................................................50

Load luggage ................................................... 50

Main parts

..............................................................51

Controls ...............................................................51

Instrument panel .............................................53

Steering lock .....................................................57

Preliminary checklist

......................................58

Running-in rules

.................................................60

Use (procedures)

.................................................60

Starting ................................................................60

Starting o ..........................................................61

Using the gears .................................................62

Stopping ..............................................................62

Maintenance

.........................................................62

Periodic maintenance chart .........................63

Engine oil ............................................................65

Tyre inﬂation pressure, tyre change ..........67

Clutch .................................................................68

Fuel .....................................................................69

Auto-mix unit..................................................70

Brakes ................................................................71

Suspensions .....................................................74

Chain ..................................................................77

Air ﬁlter ..............................................................78

Coolant ..............................................................79

Carburettor/throttle control ................ 80/81

Spark plug ........................................................81

Electrical system and headlamps ..............83

Cleaning the vehicle and inactivity ...........83

Specifications

.......................................................85

Notes

..........................................................................88

Fast guide of reference

.............................134

Lubricants table

..............................................135

Changes applied..................................................48

Rear view mirrors............................................83

47

ENGLISH

INTRODUCTION

This handbook is an integral part of the vehicle

and must accompany it if resold.

FANTIC MOTOR

reserves the right to make

changes to the models described in this hand-

book without notice, while guaranteeing the es-

sential features described and shown herein.

No part of this handbook may be reproduced

without the prior permission of the Manufac-

turer.

FANTIC MOTOR

cannot be held liable for any

copying or printing errors in this handbook.

MANUFACTURER’S DATA AND EDITION

Edition: 01/2018

GENERAL CONTENTS AND CONSULTATION

All the speciﬁcations and helpful instructions for

normal use and maintenance of the vehicle are

given in the handbook.

It is advisable to contact our Authorised Deal-

ers for maintenance and any repairs, since they

guarantee a prompt and precise service and al-

ways use original spare parts.

IDENTIFICATION

VEHICLE IDENTIFICATION NUMBER (V.I.N.)

FANTIC MOTOR vehicles have a vehicle identi-

ﬁcation number (V.I.N.) visible on the steering

head tube. When requesting original spare parts,

give this identiﬁcation number to your Dealer.

Do not change the vehicle identiﬁcation

number (V.I.N.) otherwise the guarantee

becomes invalid and there is the risk

of serious penalties and administrative

ﬁnes.

We recommend that you write the vehicle iden-

tiﬁcation number (V.I.N.) in the relative space

below in case the number becomes illegible or

damaged.

ENGINE IDENTIFICATION NUMBER

Every FANTIC MOTOR vehicle also has an engine

identiﬁcation number to be found on the crank-

case cover on the upper left side.

We recommend that you write this number in

the relative space below in case the number be-

comes illegible or damaged.

FANTIC MOTOR

Via Tarantelli, 7

31030 - Dosson di Casier (TV) Italy

Tel. +39 0422 634192

Fax +39 0422 1830124

E-mail: info@fanticmotor.it

www.fanticmotor.it

48

CHANGES APPLIED

SYMBOLS USED IN THE HANDBOOK

Scrupulously abide by the warnings preceded by

the following symbols:

Important safety norms for the vehicle

and the rider

Any modification to the vehicle, and the

removal of original components can

compromise the performance of the same,

then decrease the security level or even

make it illegal.

We recommend that you always comply

with all national and local laws and

regulations regarding vehicle equipment.

In particular, technical modifications

designed to increase performance or alter

the original characteristics of the vehicle

must be avoided.

Modifications of the vehicle involve the

cancellation of the warranty and the

decay of the homologation.

Any arbitrary modification made, relieves

FANTIC MOTOR of any responsibility

resulting from damage or injury to

property, persons or animals.

The user is personally responsible for the

choice of installation and use of accesso-

ries.

FANTIC MOTOR recommends the use of

original accessories

49

ENGLISH

BASIC SAFETY RULES

BEHAVIOUR AND DRIVING

This handbook should be read and understood

before using the vehicle.

To use this vehicle it is necessary to have fulﬁlled

all the requirements of law (driving licence, mini-

mum age, insurance, government taxes, registra-

tion, number plate, etc.). The taking of certain

medicines, alcohol and narcotics or a state of

physical fatigue and somnolence may consider-

ably increase the risk of accidents as they aect

the body.

If the rider is inexperienced, it is advisable to

become familiar with

the vehicle on sections of

road with little trafﬁc.

NEVER lend the vehicle to

inexperienced persons and in any case ensure

that the person has the necessary qualiﬁcations

for riding the vehicle.

The Highway Code must be meticulously ob-

served when riding the vehicle.

It is absolutely forbidden to race with the vehicles

outside special authorised circuits supervised by

appointed personnel. Avoid riding o road.

Always ride correctly, avoiding manoeuvres that

are abrupt or dangerous for yourself and others

(e.g.: weeling , remaining in the slipstream of the

vehicles in front, failing to comply with speed

limits, etc.).

Assess and always take into due consideration

road conditions, visibility, etc.

Always keep both hands on the handlebars in or-

der to steer properly and always keep both feet

on the relative footrests.

Under no circumstances is it allowed to stand up

or to stretch out limbs while riding.

While riding it is a good rule to pay the utmost

attention, avoiding being distracted or inﬂuenced

by persons, things, actions (e.g. do not smoke,

eat, drink, read, etc.).

The vehicle should always be kept in perfect

condition, checking that the fuel, brake ﬂuid and

coolant are always within the recommended lev-

els.

Only use speciﬁc lubricants and fuels of the type

indicated in the relative tables for the vehicle in

question.

After a fall, check all the controls, levers, pipes,

cables, braking systems, wheels and tyres for

damage.

If any damage is found, do not ride the vehicle,

but have it suitably transported (complying with

safety and legal regulations) to a

FANTIC MO-

TOR authorised dealer.

It is forbidden to change in any way

whatsoever the position, angle or colour

of: number plate, turn indicators, lighting

devices and horns. Do not make techni-

cal changes to increase performance or

to alter the original characteristics of the

vehicle in any way.

Such changes lead to cancellation of the war-

ranty and may jeopardise the performance and

therefore decrease the level of safety of the ve-

hicle or even make it illegal and subject to penal

sanctions.

Compliance with all legal provisions as well as

national and local regulations regarding vehicle

equipment is recommended at all times.

CLOTHING

Before starting the vehicle, always put a helmet

on and fasten it correctly.

The helmet must be:

- approved;

- intact;

- the correct size;

- with intact and clean visor.

Wear close-ﬁtting protective clothing without

dangling accessories (e.g. ties, belts, cords,

scarves, etc.), which could be entrapped and cre-

ate problems in steering the vehicle.

Preferably light coloured or reﬂecting clothing is

recommended in order to be more visible and

be better protected in the event of a fall.

If sharp pointed objects are worn they could be

dangerous in a fall, for example:

- keys;

- pens;

- glass containers, etc.

All these recommendations are also applicable

for the passenger.

50

ACCESSORIES

FANTIC MOTOR

advises using original accesso-

ries obtainable from authorised dealers.

If the installed accessories are other than origi-

nal, the user must be responsible for the choice

and for correct installation of the same.

Under no circumstances must the accessory:

- limit travel of the suspensions;

-

cover any part of the acoustic or visual de-

vices;

-

limit use of the steering and controls (brakes,

throttle, etc.);

- reduce the steering angle;

- hinder the rake of the vehicle in cornering.

Any large fairing and windscreen mounted on

the vehicle could reduce its stability.

The speciﬁc

FANTIC MOTOR

accessories except-

ed, do not install or make changes to the electri-

cal equipment: there could be a dangerous fail-

ure of current that is necessary for the acoustic-

and visual warning devices to work.

LOAD

Loading luggage on the vehicle could aect

steering and it is therefore advisable to keep

the luggage on the vehicle’s centre of gravity if

possible so that the weight is evenly and well

distributed.

Ensure that the load is ﬁrmly secured to the vehi-

cle (under no circumstances secure it to the han-

dlebars, the forks or the front mudguard/fender).

A load secured in this way would aect the re-

sponse of the vehicle in cornering, decreasing its

stability and controllability.

When carrying luggage, take care that it does not

project excessively and check that it does not

cover the acoustic and visual warning devices.

WARNING

It is recommended, after the ﬁrst hours of use,

to check all the torques with particular attention

to:

A Front / Rear brake caliper

B Wheels axle

C Rear sprocket

D Engine bolts

E Rear suspension mounting nuts

F Wheels spokes

G Rear frame

The vehicle is equipped by catalytic exhaust (ac-

credited Euro4) that can catch up high tempera-

tures.

Absolutely avoid the contact with body

parts, clothes inflammable materials !

WARNING

If necessary consult a FANTIC MOTOR dealer.

51

ENGLISH

MAIN PARTS

Legend

Pos. Description

1 Horn button

2 Beam diverter

3 Stop engine switch

4 Cold start device or choke

5 Clutch control lever

6 Fuel ﬁller cap

7 Fuel tank

8 Engine idling speed adjusting

screw

9

Auto-Mixer oil reservoir ﬁller cap

10 Auto-Mixer oil reservoir

11 Air ﬁlter

12 Steering lock

13 Spark plug

14 Gear lever

15 Fuel tap

16 Left footpeg

17 Side stand

18 Chain

19 Horn

CONTROLS

(*)

52

Legend

Pos. Description

20 Throttle control

21 Front brake lever

22 Front brake ﬂuid tank

23 Coolant radiator cap

24 Coolant radiator

25 Rear brake ﬂuid tank

26 Kick starter

27 Right footpeg

28 Gear oil drain plug

29 Rear brake pedal

30 Gear oil level plug

31 Gear oil ﬁller cap

53

ENGLISH

Speedometer

• Display range: 0-360 km/h (0-225 MPH).

• Display unit: km/h o MPH

Indicator lights

• High beam light (Blue).

• Direction lights (Green).

• Oil light (Red)

• Neutral light (Green)

Odo meter

• Display range: 0-99.999 km (mile), reset

automatically after 99.999 km (mile)

• Display unit: 1 km (miglia)

Trip meter

• Display range: 0-999,9 km (mile), (mile), reset

automatically after 999,9 km (mile)

• Display unit: 0,1 km (mile)

SELECT Botton

• Press the SELECT Botton in the main

screen to switch between 12/24 hour

mode, speedometer record, topwatch,

and MAX record

ADJUST Botton

• Press the ADJUST Botton in the main screen

to switch between ODO, Trip A/B, Total Hour

Meter and Hour meter A/B

• Press and hold the Adjust botton for 3

seconds in Trip A/B screen to reset.

• Press and hold the Adjust botton for 3

seconds in Hour meter A/B screen to reset.

Tool battery level

• Display range: 4 levels.

• Clock : 12/24 hour MODE

• Stopwatch : According to setup distance to

record the testing time.

• Speed Log : Average speed and max speed

record

DASHBOARD Function

Battery Replacement

When the battery level is low, proceed with replacement as in-

dicated below.

1. Remove the instrument from the support by unscrewing the

two support screws (A).

2. Remove the battery cap (B) by unscrewing it with a coin or a

mATHEADSCREWDRIVER

3. Proceed to replace the battery (C mod.2032) and close the

cap, taking care to reinsert the gasket (D) in its seat. Then reas-

semble the instrument.

54

Adjust button functions

• In main screen, press the Adjust button once to

switch the funciont to odometer to trip.

• Once you reach the trip screen by pressing the

Adjust button you can switch from trip A to trip to B.

• Hold pressing the Adjust button for 3 seconds to

reset the trip B.

• Press the Adjust button to switch from trip A to trip B.

• Hold pressing the Adjust button for 3 seconds to

reset the trip B.

• Press the Adjust button to switch from trip B to total

hour meter.

• Press the Adjust button to switch from total hour

meter to hour meter A.

• Hold pressing the Adjust button for 3 seconds to

reset the hour meter A

• Press the Adjust button to switch from hour meter

A to hour meter B

• Hold pressing the Adjust button for 3 seconds to

reset the hour meter B.

• Press the Adjust button to switch from hour meter

B back to the main screen.

Select button functions

• In main screen, press the Select button for 3

seconds to switch between 12/24 hour mode.

NOTE If 24 hour mode is chosen, the AM/

PM simbol will not be displayed.

• Press the Select button during the main sreen to

switch from Clock to Stopwatch.

• Hold pressing the Select button for 3 seconds to

reset the Stopwatch.

55

ENGLISH

• Press the Select button to switch from Stopwatch

to Speed Record.

• Hold pressing the Select button for 3 seconds to

reset the Speed Record.

NOTE Average speed and the Max speed

display in 3 seconds rotation.

• Press the Select button to switch from Speed

Record back to the main screen.

Adjust + Select X 3 function

Tire circumference setting

• In main screen, press down the Adjust+

SelectX3 to enter the tire circumference and

sensing point selling (for changing different size tire.)

• Press the Adjust button to enter the tire

circumference setting.

• Press the Adjust button to enter the tire

circumference setting. In this example the tire

circumference is 1,300 mm.

NOTE he circumference of the rear tires

must be set to 2090mm and 9 pulses for

Motard and 2290mm and 9 pulses for

Enduro models.

The digit you set is from left to right in

order.

• In this example the tire circumference setting is

changed from 1,000 mm to 1,300 mm.

• Press the Select button to change the setting.

• Press the Adjust button for three times to enter the

sensing point setting

Setting point of tire detection

56

• Press the Select BUTTON TO CHANGE THE lGURE BY

entering the value 1

NOTE: The range inside which it is possible

to change the detection point is from 1 to 9.

• Press the Adjust button will return you back to the

menu and circumference point of the tire detection

Clock setting

• Press the Adjust button to switch to the speed

menu to the dock (Hour) setting.

• Press the Select button to enter the the clock (Hour)

setting.

• Press the Select button to choose the hour you

want to set. In this example whe st the hour at 14:00.

NOTE Setting range: 0-24 H.

NOTE Sequent of cursor movement: Hours

Ten-Digit of Minute>Single Digit of Minute.

• Press the Adjust button to enter the minute setting.

• Press the Select button to choose the minute you

want to set. In this example we change the setting

to 14:05

NOTE Setting range: 0-59 minutes.

• Now the minute is changed from 14:00 to 14:05

• Press Adjust button to get back to Clock setting

screen.

• Press the Select button to switch to the Clock menu

to the Test menu (Stopwatch distance setup entering

screen.)

• Press Adjust button to enter the distance setup for

Stopwatch. In this example Distance for Stopwatch

setting value was changed from 300 to 350.

• Press Adjust button to go back to the Stopwatch

setting screen

• Press the Select button to change the setting

NOTE The range of distance for Stopwatch

is from 100m to 2000m.

• Hold pressing the Adjust button for 3 seconds to go

back to main screen.

57

ENGLISH

STEERING LOCK

Never leave the key inserted in the steering lock

while the vehicle is running.

To lock the steering, put the vehicle on the stand

and then turn the handlebar fully to the right.

Turn the lock cover upwards.

Insert the key into the lock, turn counter-clock-

wise and press.

Release the key and remove it.

The key comes with the motorcycle.

58

PRELIMINARY CHECKLIST

Part

Check

Disk brake, front and rear regular braking (smoothly, without skidding) upon application and release;

correct no-load travel and good sliding of front and rear brake lever;

brake ﬂuid level in tank, front and rear;

for any leaks along the braking circuit (brake ﬂuid tank, brake hose pipe, brake caliper), front and

rear;

front and rear brake pads for wear.

Throttle control that twisting of the handle control and acceleration of the engine are soft, continuous and smooth.

Gear oil correct level (see relative table under MAINTENANCE).

Wheels and tyres tyre pressure (see relative table under MAINTENANCE);

tyre tread for wear;

general state of tyres and wheels;

the tread for foreign matter and remove;

for any damage.

Clutch proper operation (without binding, jerking or slipping) upon activation and release;

correct no-load travel and good sliding of clutch control lever.

Steering complete, even, smooth rotation;

no play.

Stand complete, even, smooth rotation;

no play on fulcrum pin;

correct retraction of stand to rest position;

that the springs keep the stand in the rest position without play.

Engine stop switch correct operation.

Kick starter correct operation.

59

ENGLISH

Part

Check

Driving chain slack;

chain, sprocket and ring gear for wear;

cleanliness and lubrication.

Fuel tank that the fuel tap lever turns freely to all positions;

that the fuel tap lever is in the “ON” position;

fuel level;

fuel cap closure;

for any leaks along the fuel circuit (fuel tank, fuel pipes).

Auto-Mixer oil reservoir correct operation of the oil indicator light;

mixing oil level;

mixer oil reservoir cap closure;

for any leaks along the mixing oil circuit (mixer oil reservoir, coolant pipes).

Coolant correct level;

for any leaks along the coolant circuit (coolant tank).

Instrument panel instrument panel function settings (if envisaged);

lights;

general operation

direction indicator telltale

full beam indicator light;

low mixing oil warning light - neutral indicator light

Acoustic and visual devices horn;

headlamp and tail lamp;

stop light

direction indicators

60

USE

After having checked that there is fuel in the

tank, open the fuel tap on the tank.

Release the steering lock if it has been engaged,

following the instructions given in the relative

section and turn the key clockwise.

STARTING

RUNNING-IN RULES

A running-in period is necessary when ﬁrst us-

ing the vehicle. This is fundamental for correct

operation and long-life of the engine.

Certain rules must be complied with during this

period to prepare the engine and vehicle parts

for subsequent top performance (after running

in).

The following tips are given as an indication to

help the user carry out a good running-in period:

failure to comply may not lead to immediate

damage, but could have a negative eect on the

subsequent efﬁciency of the engine and the ve-

hicle parts in general.

STRESS

It is important for the engine and vehicle parts to

be subjected to stress appropriately.

It is also important neither to overstress nor to

understress, as in both cases the engine and the

vehicle parts would suer.

ROUTES

When riding along mountain roads, take care not

to force the engine, brakes and suspensions. The

vehicle is more suited to travelling along wind-

ing and moderately hilly roads where the en-

gine, brakes and suspensions alternate periods

of stress with periods of reduced or no stress.

SPEED

Change the speed gradually (no sudden full

throttling).

Full throttling is allowed, but do NOT travel for

long stretches with the accelerator handle con-

trol fully twisted (full speed).

BRAKING

The brake pads are new at the time of purchase;

the friction surface does not create perfect fric-

tion on the disks at ﬁrst. To be fully operative the

surface must be run-in, after which it will adhere

perfectly to the disk during braking. Running-in

requires approximately 200 km (125 mi) of ur-

ban route.

During this period, take into account that you

will need longer braking spaces and apply the

brake lever more forcefully. Abrupt and pro-

longed braking is to be avoided.

NOTE:

the ﬁrst 1000 km (625 mi) represent the

end of running-in threshold, but only after 1000

km (625 mi) is best performance of the vehicle

obtained.

During the ﬁrst 500 km (312 mi), ensure that any

maintenance operations envisaged for this mile-

age are carried out.

61

ENGLISH

Put the gear lever in neutral, vigorously press

the kick starter with your foot while at the same

time twisting the accelerator handle control with

moderation.

In the case of a cold start, see the next para-

graph.

If the low Auto-mix oil warning light comes on

during normal running of the engine, this means

that the mixing oil level has reached reserve and it

is therefore necessary to top up the Auto-mix oil.

Do not keep the kick starter pressed nor touch it

again once the engine has started.

COLD START

The vehicle is ﬁtted with a cold start device or

choke. It is controlled either by a lever located

above the clutch lever on the left of the handle-

bar or by a button on the carburettor.

Starting by button on carburettor

To start by using the button on the carburettor,

raise the actual button and then release it; it

should remain raised. Press on the engine kick

starter.

When the engine has started, push the button

down.

Gradually release the clutch and at the same

time throttle with moderation.

STARTING OFF

After having warmed up the engine, use the

clutch control lever and engage 1st gear (gear

lever downwards).

Prolonged connection of the choke

(with engine running) could jeopard-

ise engine operation and efﬁciency.

62

MAINTENANCE

INTRODUCTION

Before carrying out any maintenance or inspec-

tion on the vehicle, switch o the engine and

wait for it and the exhaust system to cool to

avoid the danger of burns.

Some vehicle parts are harmful or even toxic and

care must be taken when handling them.

Check that the following norms are satis-

fied:

-

The place where the work will be carried out

must be sufﬁciently ventilated and there must

be a sufﬁcient change of air in the room.

-

The area where the work is carried out must

not be dusty, dirty or cluttered with other

parts not belonging to the vehicle.

-

The tools and equipment must be suitable for

the type of maintenance to be carried out.

-

Wear suitable clothing (work overalls), work-

ing gloves, latex gloves, protective goggles

(or mask) during maintenance that requires

them.

-

Have original spare parts to hand or the nec-

essary liquids for maintenance to be carried

out (such as brake pads, gear oil, brake ﬂuid,

coolant).

Unless expressly described otherwise, reassem-

ble units that have been disassembled by pro-

ceeding in the reverse order to the disassembly

operations.

The user can normally carry out routine mainte-

nance work, even though speciﬁc tools/equip-

ment and a technical preparation may some-

times be required.

STOPPING THE ENGINE

Do not use the engine stop switch

when the vehicle is running (this

would cause a MOMENTARY stop of

the engine and subsequent restart

upon releasing the switch; this could

damage the engine and in particular

cause loss of control over the vehi-

cle).

To turn the engine o, stop the vehicle and put

the gear lever in neutral.

Only then press the engine stop switch and keep

it pressed until the engine comes to a COM-

PLETE stop.

Put the vehicle on its side stand after having dis-

mounted from the left side of the vehicle and if

necessary engage the steering lock, see page 69

under the paragraph STEERING LOCK.

USING THE GEARS

To shift gear, let go of the accelerator handle

control, move the clutch lever and raise the gear

lever to upshift or lower to downshift.

If it is the ﬁrst time you are riding a motorcycle, it

is as well to familiarise yourself with the controls

and their functions.

63

ENGLISH

La pagina sta caricando ...

Fantic Motor Fantic 50 Series Manuale utente

Questo manuale è adatto anche per

Fantic Motor Fantic 50 Series Manuale utente

in altre lingue

Altri documenti