Hama 00062741 Manuale del proprietario

Marca: Hama

Modello: 00062741

Tipo: Manuale del proprietario

Hama GmbH & Co KG

D-86651 Monheim/Germany

www.hama.com

Die Konformitätserklärung nach der R&TTE d

Richtlinie 99/5/EG ﬁ nden Sie unter www.hama.com

See www.hama.com for declaration of g

conformity according to R&TTE Directive 99/5/EC guidelines

La déclarationde conformité à la directive f

R&TTE 99/5/CE se trouve sur www.hama.com

La declaración de conformidad según la e

directiva R&TTE 99/5/CE la encontrará en www.hama.com

De conformiteitsverklaring conform de o

R&TTE-richtlijn 99/5/EG vindt u onder www.hama.com

La dichiarazione di conformità secondo la i

direttiva R&TTE 99/5/CE è disponibile sul sito

www.hama.com

A declaração de conformidade segundo a p

directiva R&TTE 99/5/CE pode ser consultada em

www.hama.com

Konformitetsförklaring enligt R&TTE riktlinje s

99/5/EG ﬁ nner du på www.hama.com

Radio- ja telepäätelaitteita koskevan m

direktiivin 99/5/EY mukainen vaatimustenmukaisuusvakuutus löytyy osoitteesta

www.hama.com

Overensstemmelseserklæringen i henhold til R&TTE-retningslinierne j

ﬁ nder du under HYPERLINK „http://www.hama.com”

Deklaracja zgodności według dyrektywy

R&TTE 99/5/EG dostępna na stronie internetowej www.hama.com

A megfelelőségi követelmények megegyeznek

az R&TTE Irányelvek 99/5/EG ajánlásaival www.hama.com

Prohlášení, o shodě podle směrnice

R&TTE 99/5/EG, naleznete na www.hama.com

Prehlásenie o zhode podľa R&TTE smernice

99/5/EG nájdete na www.hama.com

Τη δήλωση συμμόρφωσης σύμφωνα με την

οδηγία 99/5/EΚ περί R&TTE θα τη βρείτε στη διεύθυνσηwww.hama.com

00062741/09.07

All listed brands are trademarks of the corresponding companies.

Errors and omissions excepted, and subject to technical changes.

Our general terms of delivery and payment are applied.

Software: (D) (GB) (F)

(D) Dieses Gerät darf nur in den folgenden Ländern betrieben werden:

(GB) The operation of this device is only allowed in the following countries:

(F) Cet appareil ne peut être utilisé que dans les pays suivants:

(E) Este aparato se puede utilizar sólo en los países siguientes:

(I) L’uso di questo apparecchio é ammesso soltanto nei seguenti Paesi:

(NL) Dit apparaat mag alleen gebruikt worden in de volgende landen:

(DK) Dette apparat må kun benyttes i følgende lande:

(PL) Urządzenie sprzedawane jest tylko w następujących krajach:

(H) Ez a készülék a következő országokban üzemeltethető:

(CZ) Tento přístroj se smí používat pouze v následujících zemích:

(SK) Toto zariadenie sa môže používať len v týchto krajinách:

(S) Denna apparat får endast användas i följande länder:

(FIN) Tätä laitetta saa käyttää vain.

(P) Este aparelho pode ser utilizado somente na.

(GR) Αυτή η συσκευή επιτρέπεται να λειτουργεί μόνο στις παρακάτω χώρες:

(D) (A) (CH) (GB) (F) (B) (I) (NL) (E) (DK) (S) (H) (PL) (CZ) (SK) (GR) (P) (FIN) (L) (IRL)

0681

WIRELESS LAN

00062741

WLAN PC Card

300 Mbps

Contents

1. Installing the driver and conﬁguration program on Windows 2000/XP........................... Page 03

2. The conﬁguration program – introduction and operation on Windows 2000/XP........... Page 04

2.1 WPS Automatic conﬁguration................................................................................................ Page 04

2.2 Detailed conﬁguration.............................................................................................................. Page 05

2.2.1 Creating a new proﬁle..................................................................................................... Page 05

2.2.1.1 Infrastructure mode.......................................................................................... Page 06

2.2.1.2 Ad-hoc mode...................................................................................................... Page 07

2.2.2 Setting the wireless LAN encryption............................................................................ Page 07

2.2.2.1 WEP encryption................................................................................................. Page 08

2.2.2.2WPA/WPA2 encryption...................................................................................... Page 08

3. Installation and conﬁguration under Windows Vista ......................................................... Page 10

3.1 WPS Automatic conﬁguration................................................................................................ Page 10

3.2 Operation of the Windows Vista conﬁguration program ................................................... Page 11

3.3 Setting up an Ad-hoc network................................................................................................ Page 12

4. Conﬁguring the operating system and computer (Windows) ........................................... Page 12

5. Uninstalling the driver and conﬁguration program on Windows ..................................... Page 14

6. Installing the driver and conﬁguration program on MAC OS X ........................................ Page 14

7. Conﬁguring the operating system and computer (MAC OS X).......................................... Page 14

8. The conﬁguration program – introduction and operation on MAC OS X........................ Page 16

8.1 Quick conﬁguration .................................................................................................................. Page 17

8.2 Detailed conﬁguration.............................................................................................................. Page 18

8.2.1 Creating a new proﬁle..................................................................................................... Page 18

8.2.2 Setting the wireless LAN encryption............................................................................ Page 19

8.2.2.1 WEP encryption................................................................................................. Page 20

8.2.2.2 WPA/WPA2 encryption..................................................................................... Page 20

9. Support and contact information ........................................................................................... Page 21

Package contents:

1x Wireless LAN PC-Card 300 Mbps

1x driver CD-Rom

1x printed operating instructions

Remark concerning the positioning:

The connection quality depends strongly on the place or surroundings where you put up the WLAN

device. Please ensure that the device or its antennae are neither covered nor built in. We advise you

against putting it up near metallic objects or other electric or radiant devices.

In case of reception ﬂ uctuations or connection interruptions we recommend you to move interference

sources such as DECT telephones, mobile phones, Bluetooth devices or other WLAN networks out of the

way. If this is not possible, it may also be helpful to change the cable.

System requirements:

• Free PCMCIA/Cardbus slot

• Operating system Windows 98SE/ME/2000/XP/XP-x64 Edition/Vista or MAC OS X 10.3.x/10.4.x

Operating Instruction

Safety instructions:

Do not operate the device in damp or extremely dusty environments. Protect the device from pressure

and impact. The device may not be opened or moved during operation.

1. Installing the driver and conﬁguration program

on Windows 2000/XP

Before installation, please save any open

documents you may be working on. Then close all

running programs.

Insert the CD-ROM provided in the drive.

Usually, the CD starts automatically. If the menu

does not start automatically, double-click the

corresponding CD-ROM drive icon in My Computer.

The following window opens after the program

starts:

Select the required language. The following window is displayed when you select the language.

This installation process is suitable for Windows

98SE/ME/2000/XP/XP-x64 Edition/Vista.

Click Install (Win2000/XP) to continue with the

installation. Click User Guide to open the operating

instructions. Adobe Reader is required to display

PDF ﬁ les. If you have not yet installed Adobe

Reader, you will ﬁ nd a free version on the enclosed

driver CD. Click Download driver to download the

latest driver from the Hama website. This allows

you to check whether drivers have now been deve-

loped for previously unsupported systems. Click Back to return to language selection.

When you select Install, the InstallShield Wizard is loaded. This can take a few seconds. Please wait

until the InstallShield Wizard starts.

Read the licence agreement. Select “I accept the terms of the license agreement” if you accept them

and then click Next.

For Windows XP users only

The next screen prompts you to choose whether you want to conﬁgure the

Wireless LAN Adapter using the Hama Conﬁguration Program or the conﬁguration

program integrated in Windows.

We recommend that you use the Hama Conﬁguration Program.

To do so, select Hama Wireless Utility and click Next.

In the next screen, select Conﬁgure for best WiFi compatibility and click Next.

Then click Install to start the installation and connect the WLAN adapter to the computer.

Click Finish to complete the installation. You may have to restart the operating system.

2. The conﬁguration program – introduction and operation on Windows 2000/XP

Open the Hama Conﬁguration Program. To do so, click Start -> Programs -> Hama Wireless LAN ->

Hama Wireless LAN Utility. If the program is already running in the background, you will ﬁ nd in the

task bar at the bottom right of the screen:

Click the circled symbol to open the utility

from the task bar. The Hama Wireless LAN

Utility starts with the following screen,

whereby the values in the columns may be

different. This screen shows all available

wireless networks. The lower section of

this window shows the connection status

(Connected / Disconnected). Click Update

to search for wireless networks again.

2.1 WPS Automatic conﬁguration

WPS (WiFi Protected Setup) is a function

that makes the security conﬁguration of

the Wireless LAN connection easier. In

order to be able to use the function, the

router/access point and the remote station

(WLAN USB stick, PCI card or PCMCIA

card) must have the WPS function. To

carry out the security conﬁguration,

proceed as follows:

The router/access point speciﬁes which encryption and which key is used. The encryption entered

here applies to all users of the network.

There are two methods:

a) Conﬁguration using the button

Press the WPS button on the router/access point. Within two minutes, you must press the

PBC button on the WPS tab page in the WLAN adapter’s conﬁguration program. The connection

is now established automatically.

b) Pin code

Make a note of the pin code, which is displayed in the WLAN adapter’s conﬁguration program.

Select the target network in the upper list and then click PIN. Switch to the user interface of the

router. If your router supports this method, you will ﬁ nd an entry ﬁ eld for the pin code in the

WPS settings. Enter the code you noted earlier and start the transmission. The connection is

now established automatically.

If the connection is successful, a proﬁle is created, which is restored automatically when you

reconnect.

For detailed information on setting encryption, please see Page 7, under the heading:

Setting the wireless LAN encryption.

2.2 Detailed conﬁguration

When conﬁguring, it is useful to create a proﬁle. A proﬁle serves to save various settings for a

connection under a certain name. For example, if you want to connect to various wireless networks,

you can save the settings for the networks in proﬁles, which allows you to change the conﬁguration

quickly.

2.2.1 Creating a new proﬁle

You need the following information to create a proﬁle:

• SSID (network ID): This is the name of the required network.

• Encryption used in the target network

• Network type (type of network): Infrastructure or ad-hoc

There are two basic ways to create a proﬁle:

Version 1 : Change to the Proﬁle tab and click Add.

Version 2 : Open the Network tab. All networks are listed in this tab. Select the

required network in the list and click Add to proﬁle.

For hidden networks only:

If the SSID ﬁ eld is empty, the router or access point is set to hide the network.

The SSID cannot therefore be copied automatically.

In both cases, the following window is

displayed on the screen:

The device supports the infrastructure and

ad-hoc network types.

Infrastructure: Select this type if you want

to connect this wireless LAN device to a

wireless LAN router or access point.

Ad-hoc: Select this type if you want to connect directly to another wireless LAN client device, e.g.

another USB stick or a WLAN PCI card without a wireless LAN router or access point.

Two WLAN client devices are required for this.

2.2.1.1 Infrastructure mode

First enter a name for your proﬁle (Proﬁle name), e.g. “PROF1”.

If you have selected version 1 to create the new proﬁle, you must enter the network ID (SSID) of the

target network in the SSID ﬁ eld. This is in the wireless LAN settings in your router or access point or

you can ask the person in charge. If you have selected version 2, the SSID has already been copied

automatically from the network overview.

To reduce the energy consumption, you can run the device in Power saving mode (PSM). In this

mode, certain functions are deactivated or run at a lower setting if they are not fully used. Select

Constantly Awake Mode (CAM) if you want to work at full power all the time.

Select Infrastructure under network type. This mode facilitates connection to a wireless LAN router

or access point. The settings for TX Power, RTS Threshold and Fragment Threshold can be left at the

default settings.

If your network uses encryption, switch to the Authentication and Security tab and continue

conﬁguration under Setting wireless LAN encryption.

If your network is not encrypted, click OK to accept the settings. To activate the proﬁle created,

switch to the Proﬁles tab, select the proﬁle and then click Activate.

2.2.1.2 Ad-hoc mode

First enter a name for your proﬁle (Proﬁle name), e.g. “PROF1”.

If you have selected version 1 to create the proﬁle, you must enter the network ID (SSID) of the

target network in the SSID ﬁ eld. This is in the wireless LAN settings in your router or access point or

you can ask the person in charge. If you have selected version 2, the SSID has already been copied

automatically from the network overview.

To reduce the energy consumption, you can run the device in Power saving mode (PSM). In this

mode, certain functions are deactivated or run at a lower setting if they are not fully used. Select

Constantly Awake Mode (CAM) if you want to work at full power all the time.

Select Ad-hoc under network type. This mode allows you to connect to other wireless LAN client

devices, e.g. USB sticks, PCI cards or cardbus. The settings for TX Power, Preamble, RTS Threshold

and Fragment Threshold can be left at the default settings. You must also set the wireless LAN

channel used under Channel. In Europe, there are 13 channels in the 2.4 GHz frequency range.

If your network uses encryption, switch to the Authentication and Security tab and continue

conﬁguration under Setting wireless LAN encryption.

If your network is not encrypted, click OK to accept the settings. To activate the proﬁle created,

switch to the Proﬁles tab, select the proﬁle and then click Activate.

2.2.2 Setting the wireless LAN encryption

First, it is important to understand a range of terms. The next section will explain the main terms

used here:

Authentication: Authentication is a process in which the identity, e.g. of a person is determined

based on a certain characteristic. This can be done by ﬁ ngerprint, password or any other proof of

authorisation.

Encryption: Encryption is a process in which a plain text is transformed into a coded text via an

encryption process (algorithm). One or more codes can be used for this. It must also be

mentioned that each individual encryption process offers one or more authentication options.

Please switch to the Authentication and Security tab.

This device can be used with the following encryption types:

64 and 128 bit WEP encryption WPA and WPA2 encryption

Note!!! Encryption is deactivated by default. However, for security

reasons, we recommend that you always use encryption.

2.2.2.1 WEP encryption

Wired Equivalent Privacy (WEP) is a standard encryption algorithm for WLAN. It both controls the

access to the network and guarantees the integrity of the data. This method is considered vulnerable

due to a range of weaknesses.

If you want to use WEP encryption, select

WEP under encryption. Two options are

available for the Authentication type under

WEP.

Select Open if all clients are to be enabled

for WLAN. Now there is virtually no other

authentication.

Select Shared if you want to use authentication with the challenge response process. A shared code

is used for authentication in this method. All WLAN users must know this code.

All other selection options under Authentication type are meaningless under WEP.

You can now store four codes in the lower section of the window. The selected code is always used.

64 bit or 128 bit encryption is supported. 128 bit encryption is more secure. First select whether you

want to use Hex (allows characters from 0-9 and a-f to be used) or ASCII characters (You can use

any characters). The setting and the selection of either 64 or 128 bit encryption determines the length

of the code to be entered.

WEP 64 bit ASCII requires 5 characters

WEP 128 bit ASCII requires 13 characters

WEP 64 bit HEX requires 10 characters

WEP 128 bit HEX requires 26 characters

Examples: 64 bit Hex (10 characters) = 231074a6ef

64 bit ASCII (5 characters) = j31n.

128 bit Hex (26 characters) = 231074a6b9773ce43f91a5bef3

128 bit ASCII (13 characters) = urlaub2006.+0

2.2.2.2 WPA/WPA2 encryption

Wi-Fi Protected Access (WPA) is an encryption method for WLAN. WPA contains the WEP

architecture, but offers additional protection via dynamic codes, which are based on the

Temporal Key Integrity Protocol (TKIP), and also offers pre-shared keys (PSK) or extensible

authentication protocol (EAP) for user authentication. However, a radius server is required for this.

WPA2 is a development of WPA and uses a different encryption algorithm, advanced encryption

standard (AES).

WPA offers two types of authentication, either pre-shared key or authentication via special

authentication protocols, which are generally variations of EAP (Extensible Authentication Protocol).

An authentication server (RADIUS server) is used for the latter authentication method, which is rarely

used for private applications. Your administrator can give you the information you require to conﬁgure

this authentication method.

The pre-shared key method is more common and offers a high degree of security.

To use WPA encryption, select WPA-PSK

under Authentication type and TKIP under

Encryption. Now enter the code used in the

WPA preshared key ﬁ eld. The code

entered must be absolutely identical with

that used in the network. It must be min. 8

and max. 63 random characters for ASCII.

Letters (A-Z), numbers and punctuation

marks can be used. 64 characters are required for HEX, whereby only characters from 0-9 and a-f can

be used. If you do not have this code, it can be found in your router/access point or you can ask the

person responsible for these devices. Save the settings and click OK.

To use WPA2 encryption, select

WPA2-PSK under Authentication type

and AES under Encryption.

Now enter the code used in the WPA

preshared key ﬁ eld.

The code entered must be absolutely

identical with that used in the network.

It must be min. 8 and max. 63 random characters for ASCII. Letters (A-Z), numbers and punctuation

marks can be used. 64 characters are required for HEX, whereby only characters from 0-9 and a-f can

be used. If you do not have this code, it can be found in your router/access point or you can ask the

person responsible for these devices.

Save the settings and click OK.

To activate the proﬁle created, switch to the Proﬁles tab, select the proﬁle and then click Activate.

3. Installation and conﬁguration under Windows Vista

Before installation, please save any open

documents you may be working on. Then close all

running programs. Insert the CD-ROM provided in

the drive. Usually, the CD starts automatically. If the

menu does not start automatically, double-click the

corresponding CD-ROM drive icon in My Computer.

Remark: Please click “Run autorun.exe” if the

window “Auto Play” appears when the CD-ROM

has been inserted. The following window opens

after the program starts: Select the required

language.

Click “Install (Win Vista).” The message “An unidentiﬁed

program wants access to your computer” appears. Allow

access by clicking “Allow”. Click -> Next in the next

window “Welcome to the InstallShield Wizard…”.

Continue with “Install” and connect the WLAN stick with

your computer.

Wait until the window “InstallShield Wizard completed”

appears and ﬁ nish with Finish.

3.1 WPS Automatic conﬁguration

WPS (WiFi Protected Setup) is a function

that makes the security conﬁguration of

the Wireless LAN connection easier. In

order to be able to use the function, the

router/access point and the remote station

(WLAN USB stick, PCI card or PCMCIA

card) must have the WPS function. To

carry out the security conﬁguration,

proceed as follows:

The router/access point speciﬁes which

encryption and which key is used. The

encryption entered here applies to all users of the network.

There are two methods:

a) Conﬁguration using the button

Press the WPS button on the router/access point. Within two minutes, you must press the

PBC button on the WPS tab page in the WLAN adapter’s conﬁguration program. The connection

is now established automatically.

b) Pin code

Make a note of the pin code, which is displayed in the WLAN adapter’s conﬁguration program.

Select the target network in the upper list and then click PIN. Switch to the user interface of the

router. If your router supports this method, you will ﬁ nd an entry ﬁ eld for the pin code in the

WPS settings. Enter the code you noted earlier and start the transmission. The connection is

now established automatically.

If the connection is successful, a proﬁle is created, which is restored automatically when you

reconnect.

3.2 Operation of the Windows Vista conﬁguration program

Click the symbol with the two computer monitors in the task bar with

the left mouse button:

Afterwards, you can establish connections to existing WLAN

networks. Click “Wireless networks are available” for this purpose.

Wait a minute if this option cannot be selected. Please check if the

WLAN router or Access Point is operational if this does not help.

The found networks are displayed now. Select the correct network

and click “Connect”.

Remark concerning hidden networks: the name is not shown in this

case. Instead of that, it is called “Unnamed Network”. When the

connection has been established, you are asked for the name.

Afterwards, you are mostly asked to enter

the network security key. For reasons

of safety, we advise you against using

uncoded networks. Click “Connect” for

conﬁrmation. Windows establishes now

the connection to the desired WLAN.

Afterwards, you can store the network

and start it automatically next time. The

connection is so automatically established

in future. Finish the conﬁguration by

clicking with the mouse “Close”.

3.3 Setting up an Ad-hoc network

This enables direct connections to another Wireless LAN Client device, e.g. a USB stick or a WLAN PCI

add-in card. No wireless LAN router or Accesspoint is required for this. If such a network already exists,

you can establish a connection with this one as described above. If it is to be set up a new, so that other

users can connect themselves, you have to proceed as described below:

Click the symbol with the two computer monitors in the task bar with the left mouse button:

Click “Connect to a network”, “Set up a connection or network” and then “Set up a wireless Ad hoc

(computer-to-computer) network”. Conﬁrm with -> Next -> Next.

In the next window, you are asked to enter

data concerning the network name and the

security type. More information is shown

if you move the mouse cursor towards the

appropriate ﬁ eld. Additional remarks

concerning the network name and WPA2

security key. Here, you should only use letters

from A-Z, as well as numbers from 0-9.

Conﬁrm your speciﬁcations with -> Next ->

Close.

4. Conﬁguring the operating system and computer (Windows)

After you have successfully installed the network adapter, you still have to install or conﬁgure a

protocol. This protocol governs the data exchange between the computer and the network. TCP/IP

is most common. Each computer has to be assigned its own address for the protocol. Automatic

address assignment is only reliable if a DHCP server exists in the network, e.g. a router or access

point. If you have one of these devices with a DHCP function, you should leave the setting on “Get

automatically”.

Proceed as follows to check the settings on your PC:

Start -> Settings -> Control panel -> Network connections

Select the connection (network adapter) via which

your PC is connected to the router, e.g. “LAN

connection”. When you right-click the corresponding

connection, the following screen is displayed when

you select Properties.

Select the Internet Protocol (TCP/IP) entry in the list

and click Properties.

Select Optain an IP address automatically

and Optain DNS server address

automatically, if there is a DHCP server in

your network. Conﬁrm by clicking OK, and

again in the subsequent window.

Your PC is now conﬁgured such that the

router assigns the IP address

automatically.

If you do not have a device with an

integrated DHCP server, you must assign

the IP addresses manually. The following

example describes basic setup using

manual address assignment. For local

networks, special address ranges are

provided which are not transmitted over

the internet. As an example, a range that

you can use for your network is 192.168.1.1

to 192.168.1.254. The ﬁ rst PC is assigned the

address 192.168.1.1, the second 192.168.1.2,

the third 192.168.1.3, etc.

Select Use the following IP address and enter your IP address in accordance with the sample.

1.PC = IP address 192.168.1.1 Subnet mask 255.255.255.0

2.PC = IP address 192.168.1.2 Subnet mask 255.255.255.0

Click Ok to conﬁrm your entries.

5. Uninstalling the driver and conﬁguration program on Windows

Save all open documents and close all programs before uninstalling.

Select Start => Settings => Control Panel => Software

To do so, select Hama Wireless Utility and click Remove. At the next prompt, click Remove

completely and then Yes. Remove the WLAN adapter and then click Finish to restart the computer.

6. Installing the driver and conﬁguration program on MAC OS X

Before installation, please save any open documents you may be working on. Then close all running

programs. Ensure that you have administrator authorisations to enable you to install the driver

correctly.

Connect the device to a free PCMCIA/Cardbus slot. After the operating system has loaded completely

and the desktop is complete, insert the enclosed driver CD-ROM in your drive. An icon with the

CD-ROM then appears on your desktop. Double-click the icon and select the MAC driver directory

in the Finder window. This directory contains the DMG ﬁ le required for installation. Double click the

DMG ﬁ le to activate the image. After you activate the image, select the correct directory for your

installed MAC OS X Version and then double click the corresponding PKG ﬁ le. Installation is now

started.

Select your hard drive on which you want to install the driver and the conﬁguration program. You

must then restart the system.

7. Conﬁguring the operating system and computer on MAC OS X

After you have installed the driver, you must conﬁgure the network environment in accordance with

the new situation. To do so, proceed as follows.

Click the Apple symbol in the upper menu

bar and select the Environment menu item.

Select the “Network” setting menu item.

The following window opens.

Click OK to conﬁrm the message.

Note: If the message shown above is not displayed, the device was not correctly identiﬁed by your

PowerMac. Ensure that the device is connected properly!

After the Hama WLAN Adapter has been

properly detected, the following window

opens.

Select the New environment… option

under Environment. Name the new

environment e.g. WLAN and click the OK

button.

Select the Environment menu item again

in the Network window and select the

New environment which has also been

selected, WLAN in our case. Next, select

the Show/Display menu item in the

Network window and select the Network

conﬁgurations option.

Note: The process for selecting the con-

nections can vary depending on the MAC

model and features.

In our case, remove the tick for all con-

nections except the Ethernet connection

(en2). Then click the Activate button. The

conﬁguration process is now complete for

your system.

8. The conﬁguration program – introduction and operation on MAC OS X

As this device is not an ofﬁcial Apple Airport product, you cannot

use the Airport program integrated in the system. You must open

the enclosed utility to conﬁgure the device. Open the ﬁ nder and

select the hard drive where you installed the driver and the utility

earlier. The utility is installed in the Programs directory by default.

Double-click the icon.

The following window opens:

This screen shows all available wireless networks.

The SSID, which is used to identify WLAN devices

in the respective wireless LAN, the router MAC

address (BSSID), the signal strength (signal), the

channel used (channel), the encryption algorithm

(encryption) and the authentication (authentication)

and the type of network (network type) are

displayed.The lower section of this window shows

the connection status (Connected / Disconnected).

Click RESCAN to search for wireless networks

again.

8.1 Quick conﬁguration

First, select the required WLAN network by clicking the corresponding line in the list. The network

selected is highlighted in blue in the list. Now click the Connect button.

You are connected to the network if the selected network is run without encryption and the signal is

strong enough. This is indicated by the green symbol and Connect is shown in the status window.

If you have activated encryption, you are asked for the code. Enter the code in the corresponding

ﬁ eld.

You can enter the data required for encryption here. The data must be identical to the router or

access point settings. The authentication type and encryption are generally already selected in

accordance with the target network. Enter the code which must correspond exactly with the code

used by the router or access point. Click OK to conﬁrm after you make your entries.

If you do not have this code yourself, please contact the person responsible for conﬁguring the

router or access point. For detailed information on setting encryption, please see Page 20, under the

heading: Setting the wireless LAN encryption.

For further information on the connection made, open the Link status tab. This shows information

such as the Link quality and Signal strength.

8.2 Detailed conﬁguration

When conﬁguring, it is useful to create a proﬁle. A proﬁle serves to save various settings for a

connection under a certain name. For example, if you want to connect to various wireless networks,

you can save the settings for the networks in proﬁles, which allows you to change the conﬁguration

quickly.

8.2.1 Creating a new proﬁle

You need the following information to create a proﬁle (Proﬁle):

• SSID (network ID): This is the name of the required network.

• Encryption Type: Encryption used in the target network

• (Network Type): (type of network): Infrastructure or ad-hoc

Open the Wireless Utility. Using the Network overview (Site survey) tab, you can select the

required network and then open the dialog box using the ADD PROFILE button, or open the Proﬁle

tab and start the dialog box by clicking the ADD button.

First enter a name for your proﬁle (Proﬁle name).

Under SSID, select the network you want to

connect to from the list of available networks.

To reduce the energy consumption, you can run the

device in Power saving mode. In this mode, certain

functions are deactivated or run at a lower setting

if they are not fully used. Select CAM (Constantly

Awake Mode), if you want to run the stick at full

power all the time.

This device allows you to set up two different network types. Select Infrastructure under Network

type, if you want to connect to a router or access point. The settings for TX Power, RTS Threshold

and Fragment Threshold can be left at the default settings.

If you want to connect to another WLAN client device without a router or access point,

select 802.11 Ad-hoc.

The settings for TX Power, Channel, RTS Threshold and Fragment Threshold can be left at the

default settings.

8.2.2 Setting the wireless LAN encryption

First, it is important to understand a range of terms. The next section will explain the main terms

used here:

Authentication: Authentication is a process in which the identity, e.g. of a person is determined

based on a certain characteristic. This can be done by ﬁ ngerprint, password or any other proof of

authorisation.

Encryption: Encryption is a process in which a plain text is transformed into a coded text via an

encryption process (algorithm). One or more codes can be used for this. It must also be

mentioned that each individual encryption process offers one or more authentication options.

Now switch to the Advanced tab.

Wireless mode allows you to set the standard to be used. This depends on the other devices used

in your network. You can choose either 802.11 B only mode (11 Mbps): Then this standard only is

used; or 802.11 B/G mixed mode up to 54 Mbps): Both standards are then supported; If you are not

sure which of the standards your devices support, you should use the mixed mode (802.11 B/G mixed

mode). Make all other settings as shown in the image below.

Click Apply to conﬁrm your entries.

This device can be used with the following

encryption types:

64 and 128 bit WEP encryption

WPA Encryption

Note!!! Encryption is deactivated by

default. However, for security

reasons, we recommend

that you always use encryption.

La pagina sta caricando ...

Hama 00062741 Manuale del proprietario

Marca: Hama

Modello: 00062741

Tipo: Manuale del proprietario

Scarica il pdf

rapporto

in altre lingue

English: Hama 00062741 Owner's manual

Hama 00062741 Manuale del proprietario

Hama 00062741 Manuale del proprietario

in altre lingue

Documenti correlati

Altri documenti