Amprobe AM-TMD53 Manuale del proprietario

Categoria
Misurazione
Tipo
Manuale del proprietario
Users Manual
UÊ`iÊ`½i«
UÊi`iÕ}Ã>`LÕV
UÊ>Õ>Ê`½1Ã
UÊ>Õ>Ê`iÊÕÃ
TMD-53 / TMD-53W
Thermocouple
thermometer K/J
/ Wireless
TMD-53
Thermocouple
thermometer K/J
TMD-53W
Thermocouple
thermometer K/J
with wireless
Users Manual
June 2010, Rev.1
©2010 Amprobe Test Tools.
All rights reserved. Printed in Taiwan
English
Ìi`Ê7>ÀÀ>ÌÞÊ>`ÊÌ>ÌÊvÊ>LÌÞ
Your Amprobe product will be free from defects in material and
workmanship for 1 year from the date of purchase. This warranty
does not cover fuses, disposable batteries or damage from accident,
neglect, misuse, alteration, contamination, or abnormal conditions
of operation or handling. Resellers are not authorized to extend
any other warranty on Amprobe’s behalf. To obtain service during
the warranty period, return the product with proof of purchase
to an authorized Amprobe Test Tools Service Center or to an
Amprobe dealer or distributor. See Repair Section for details. THIS
WARRANTY IS YOUR ONLY REMEDY. ALL OTHER WARRANTIES -
WHETHER EXPRESS, IMPLIED OR STAUTORY - INCLUDING IMPLIED
WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE OR
MERCHANTABILITY, ARE HEREBY DISCLAIMED. MANUFACTURER
SHALL NOT BE LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL
OR CONSEQUENTIAL DAMAGES OR LOSSES, ARISING FROM ANY
CAUSE OR THEORY. Since some states or countries do not allow the
exclusion or limitation of an implied warranty or of incidental or
consequential damages, this limitation of liability may not apply
to you.
,i«>À
All test tools returned for warranty or non-warranty repair or
for calibration should be accompanied by the following: your
name, company’s name, address, telephone number, and proof of
purchase. Additionally, please include a brief description of the
problem or the service requested and include the test leads with
the meter. Non-warranty repair or replacement charges should be
remitted in the form of a check, a money order, credit card with
expiration date, or a purchase order made payable to Amprobe®
Test Tools.
7>ÀÀ>ÌÞÊ,i«>ÀÃÊ>`Ê,i«>ViiÌÊqÊÊÕÌÀiÃ
Please read the warranty statement and check your battery before
requesting repair. During the warranty period any defective test
tool can be returned to your Amprobe® Test Tools distributor for
an exchange for the same or like product. Please check the “Where
to Buy” section on www.amprobe.com for a list of distributors near
you. Additionally, in the United States and Canada In-Warranty
repair and replacement units can also be sent to a Amprobe® Test
Tools Service Center (see address below).
7>ÀÀ>ÌÞÊ,i«>ÀÃÊ>`Ê,i«>ViiÌÊqÊ1-Ê>`Ê>>`>
Non-warranty repairs in the United States and Canada should be
sent to a Amprobe® Test Tools Service Center. Call Amprobe® Test
Tools or inquire at your point of purchase for current repair and
replacement rates.
In USA In Canada
Amprobe Test Tools Amprobe Test Tools
Everett, WA 98203 Mississauga, ON L4Z 1X9
Tel: 877-AMPROBE (267-7623) Tel: 905-890-7600
7>ÀÀ>ÌÞÊ,i«>ÀÃÊ>`Ê,i«>ViiÌÊqÊÕÀ«i
European non-warranty units can be replaced by your Amprobe®
Test Tools distributor for a nominalv charge. Please check the
“Where to Buy” section on www.amprobe.com for a list of
distributors near you.
European Correspondence Address*
Amprobe® Test Tools Europe
In den Engematten 14
79286 Glottertal, Germany
Tel.: +49 (0) 7684 8009 - 0
*(Correspondence only – no repair or replacement available from
this address. European customers please contact your distributor.)
TMD-53/TMD-53W
15
14
10
4
1
6
3
2
5
7
8
9
TMD-53W
11
12
Third
Display
Second
Display
Main
Display
13
£®Ê/i«iÀ>ÌÕÀiÊ/Þ«i
Ó®ÊÜÊL>ÌÌiÀÞ
ήÊ8É É6ÊÊ
ÀiVÀ`Ê`i
{®Ê,i>ÌÛiÊ`i
x®Ê"Êi>Li`
È®ÊÉÊÌÃÊ
V«>À>ÌÛiÊ`i
Ç®Ê/i«iÀ>ÌÕÀiÊ
i>ÃÕÀiiÌÊÕÌÃ
n®Ê/£É/ÓÊÌiÀVÕ«iÊÀÊ
/£/ÓÊ`vviÀiÌ>
®Ê7ÀiiÃÃÊvÕVÌÊ
i>Li`ÊÊ
/xÎ7ÊÞ®
£®Êº »Ê*ÜiÀ
Ó®ÊcÊÉcÊ
ήʺ »Ê>Ì>Ê`Ê]Ê
L>V}Ì
{®Êº/£Ê/ÓÉ/£/Ó»ÊÊ
>Ê`ë>Þ
x®ÊºÉ»Ê>Ê`ë>Þ
Ȯʺ8É »ÊÊ
>Ê`ë>Þ
Ǯʺ,»Ê>Ê`ë>Þ
n®Êº-iV°ÊÕ°»ÊÊ
/À`Ê`ë>Þ
®Êº-/»
£ä®Êº/£Ê/ÓÊ/£/Ó»ÊÊ
ÊÊ-iV`Ê`ë>Þ
££®ÊºÉ»Ê-iV`Ê`ë>Þ
£Ó®ÊºÉÊ/-»ÊÊ
ÊÊ>Ê`ë>Þ
£Î®Ê7ÀiiÃÃÊÊ
ÊÊ/xÎ7ÊÞ®
£{®Êë>Þ
£x®Ê/£É/ÓÊ«ÕÌ
8
7
6
1
2 43 95
-, Ê-*9
1
" / /-
-9"-.............................................................................. 2
1 * Ê Ê -*/" ............................................ 4
 /,"1/" .................................................................... 4
Features ............................................................................ 4
"*,/" Ê -/,1/" -................................................. 5
“ Power Button........................................................... 5
cÉc” Selecting the Temperature Scale ....................... 5
” Mode...................................................................... 5
/£Ê/ÓÉ/£/Ó” Main Display Input Selection .................. 5
É” Main display Input Thermocouple Type Select .... 6
8É ” With Time Record Mode ............................6
,” Relative Mode ....................................................... 6
-iV°ÊÕ°” Selecting the Time scale ............................ 7
-/” Mode...................................................................... 7
/£Ê/ÓÊ/£/Ó” Second Display Input Selection ............... 8
É” Second display Input thermocouple type select .. 8
ÉÊ/-” Mode ......................................................8
Wireless Mode (TMD-53W only) ..................................... 8
-*/" ...................................................................... 9
 /  ................................................................... 11
2
-9"-
:Caution! Refer to the explanation in this Manual
3Complies with European Directives
Tested Comply With FCC Standards
Do not dispose of this clamp meter as unsorted
municipal waste.
:WARNING and PRECAUTIONS
UÊÊ/Ê>Û`ÊiiVÌÀV>ÊÃV]Ê`ÊÌÊÕÃiÊÌÃÊÃÌÀÕiÌÊ
ÜiÊÜÀ}ÊÛÌ>}iÃÊ>ÌÊÌiÊi>ÃÕÀiiÌÊÃÕÀv>ViÊ
ÛiÀÊÓ{6ÊÊÀÊ°
UÊÊ/Ê>Û`Ê`>>}iÊÀÊLÕÀÃ]Ê`ÊÌÊ>iÊ
Ìi«iÀ>ÌÕÀiÊi>ÃÕÀiiÌÊÊVÀÜ>ÛiÊÛið
UÊÊ,i«i>Ìi`ÊÃ>À«ÊyiÝ}ÊV>ÊLÀi>ÊÌiÊÌiÀVÕ«iÊ
i>`ðÊ/Ê«À}Êi>`Êvi]Ê>Û`ÊÃ>À«ÊLi`ÃÊÊÌiÊ
i>`Ã]ÊiëiV>ÞÊi>ÀÊÌiÊViVÌÀ°
i`iÀ>ÊÕV>ÌÃÊÃÃ
This device TMD-53W complies with Part 15 of the
FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any
interference received, including interference that may
cause undesired operation.
Ìi
This equipment TMD-53W has been tested and found
to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection. This
equipment generates, uses and can radiated radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there
3
is no guarantee that interference will not occur in a
particular installation if this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
UÊÊReorient or relocate the receiving antenna.
UÊÊIncrease the separation between the equipment and
receiver.
UÊÊConnect the equipment into an outlet on a
circuit different from that to which the receiver is
connected.
UÊÊConsult the dealer or an experienced radio/TV
technician for help.
Shielded interface cables must be used in order to comply
with emission limits.
Changes or modifications not expressly approved by the
party responsible for compliance could void the user’s
authority to operate the equipment.
7ÀiiÃÃÊ Ìi
Wireless receiver must keep a distance at least 40cm from
the meter and meter to meter distance must be at least
30cm.
4
1 * Ê Ê -*/"
Your shipping carton should include:
1 Meter
4 AAA batteries
1 Software CD ROM (THWD-10W)
1 USB Wireless Antenna (THWD-10W)
2 K type thermocouple
1 Manual
1 Plain white box
If any of the items are damaged or missing, return
the complete package to the place of purchase for an
exchange.
 /,"1/"
TThis instrument is a 5 digit, compact-sized portable
digital thermometer designed to use external K-type and
J-type thermocouples as temperature sensor. Temperature
indication follows Reference Temperature/Voltage Tables
(N.I.S.T. Monograph 175 Revised to ITS-90) for K-type
and J-type thermocouples. Two K-type thermocouple are
supplied with the thermometer.
i>ÌÕÀiÃ
UÊÊ7ÀiiÃÃÊÌÜÊÜ>ÞÃÊÌÀ>ÃÃÃ°Ê/xÎ7ÊÞ®
UÊÊÉÌÞ«iÊÌiÀVÕ«iÊÃiiVÌÊ`Õ>Ê«ÕÌ°
UÊÊcÉcÊÕÃiÀÃiiVÌÛi°
UÊÊ8É ÊÜÌÊi>«Ãi`ÊÌi]Ê6]Ê,]Ê"Ê
function.
UÊÊ/ÊÃiÌÌ}]Ê,ÊÃiÌÌ}°
UÊÊ7>À}ÊLii«iÀÊÜÌÊÉÊÃiÌÌ}°
UÊÊ,iÃÕÌÊä°£cÊÌÊä°Óc°
5
"*,/ Ê -/,1/" -
ºÊ Ê»Ê*ÜiÀÊÕÌÌ
The “ ” key turns the thermometer on or off. In the SET
mode cannot be powered off. Exit SET mode to power
off.
APO function mode
Press “ ” power key for more than 4 seconds to disable
the auto-power function.
The display will show “*"Ê"”.
ºcÉc»Ê-iiVÌ}ÊÌiÊ/i«iÀ>ÌÕÀiÊ-V>i
,i>`}ÃÊ>ÀiÊ`ë>Þi`ÊÊiÌiÀÊ`i}ÀiiÃÊiÃÕÃc®ÊÀÊ
`i}ÀiiÃÊ>ÀiiÌc®°Ê7iÊÌiÊÌiÀiÌiÀÊÃÊÌÕÀi`Ê
on, it is set to the temperature scale that was in use
when the thermometer was last turned off. To change
ÌiÊÌi«iÀ>ÌÕÀiÊÃV>i]Ê«ÀiÃÃÊÌiʺcÉc” key.
º »Ê`iÊÞÊ>Ê`ë>Þ®
Press this key to enter the Data Hold mode, the “"
annunciator is displayed. When HOLD mode is selected,
the thermometer holds the present readings and stops
all further measurements. Press the “ ” key again to
cancel HOLD mode and resume measurements. In the
MAX/MIN recording mode, press “ ” key to stop the
recording. Press “ ” key again to resume recording.
(Previously recorded readings are not erased).
Backlight function mode
Press the “ ” key for more than two seconds to turn
on the backlight. Press the key again for more than two
seconds to turn off the backlight. The backlight will
switch-off automatically after 30 seconds.
º/£Ê/ÓÉ/£/Ó»Ê>Êë>ÞÊ«ÕÌÊ-iiVÌ
The input selection indicates which input is selected
for main display; T1 thermocouple, T2 thermocouple or
6
the difference between the two thermocouples (T1-T2),
when the thermometer is turned on, it is set to T1.
ºÉ»Ê>Ê`ë>ÞÊ«ÕÌÊ/iÀVÕ«iÊ/Þ«iÊ
-iiVÌ
The “É” key selects the T1 thermocouple type, when
the main display is showing T1. When the thermometer
is turned on, it is set to the type selected when the
thermometer was last turned off.
º8É »Ê7ÌÊ/iÊ,iVÀ`Ê`iÊÊ
ÞÊ>Ê`ë>Þ®
Press “8É ” key to enter the MAX MIN Recording
mode, (displays the Maximum reading with time,
Minimum reading with time and Average reading stored
in record mode). In the this mode the automatic power-
off feature is disabled and “ »ÊiÞ]ʺcÉc” key, “,
key, “-/” key, “ÉÊ/-” key and main display
/£Ê/ÓÊ/£/Ó” key, “É” key are disabled. The beeper
emits a tone when a new minimum or maximum value
is recorded.
Press “8É ” key to cycle through the MAX, MIN
and AVG readings. If an overload is recorded, the
averaging function is stopped. In this mode, press the
"” key to stop the recording of readings, all values
are held, press again to restart recording.
To prevent accidental loss of MAX, MIN and AVG data,
this mode can only be cancelled by pressing and holding
the “8É ” key for 2 seconds. All recorded readings
are erased.
º,»Ê,i>ÌÛiÊ`iÊÞÊ>Ê`ë>Þ®
Press the “,” key to enter the relative mode, zero the
display, and store the displayed Reading as a reference
value. REL is shown on the display. Press “,” key again
to exit the relative mode. The relative reference
7
value can also be entered by the user. (See “-/Ê`i
later in this manual). When the desired relative value
has been entered, press “,” key to enter the relative
mode and than press “-/” key use the entered relative
value as a reference value. Press “,” key again to exit
the relative mode. In the relative mode, the value (can
not >±3000.0 counts) shown on the LCD is always the
difference between the stored reference and the present
reading.
º-iV°ÊÕ°»Ê-iiVÌ}ÊÌiÊ/iÊÃV>i
Press this key to display the elapsed time on the third
display in either hours and minutes or minutes and
seconds. When the thermometer is turned on, it is set to
seconds. To change the time scale, press “-iV°ÊÕð
key. Maximum elapsed time reading is 100 hours. If 100
hours is exceeded, the elapsed time resets to zero.
º-/»Ê`iÊ,i>ÌÛiÊÛ>ÕiÊÃiÌ]Ê/iÊÃiÌÊ>`ÊÉ
ÊÌÃÊÛ>ÕiÊÃiÌ®
1. Press the “-/” key to enter relative values SET
mode (Press “ /,” key to skip setting relative
value). “rÊrÊrÊr°r” is displayed on the main display.
The relative value is entered via overlay numbers,
press overlay “ /,” key to store the relative
value, and advance to elapsed time set mode.
2. Elapsed time set mode, (Press “ /,” key to
skip Elapsed time set mode) “r°rÊrÊrÊ\ÊrÊr” is
displayed in second and third display. Time (hours,
minutes,seconds) value is entered via overlay
numbers, press overlay “ /,” key to store time
value. Elapsed time starts from set time value.
3. Hi Limit value set mode, “ ” is displayed (Press
 /,” key to skip Hi Limit value set mode),
rÊrÊrÊr°r” is displayed in main display, Hi Limit
value is entered via overlay numbers, then press
8
 /,” key to store the Hi Limit value.
rÊrÊrÊr°r” is displayed in main display, Lo Limit
value is entered via overlay numbers, then press
overlay “ /,” key to store the Lo Limit value and
exit SET mode.
4. When the thermometer is turned on it uses the
relative value and Hi/Lo Limits values that were
entered when thermometer was last in use.
º/£Ê/ÓÊ/£/Ó»Ê-iV`Êë>ÞÊ«ÕÌÊ-iiVÌ
The input selection indicates which input is selected for
second display; T1 thermocouple, T2 thermocouple or
the difference between the two thermocouples (T1-T2).
When the thermometer is turned on, it is set to T2 input.
To select a different type of thermocouple use the “É
key.
ºÉ»Ê-iV`Ê`ë>ÞÊ«ÕÌÊÌiÀVÕ«iÊÌÞ«iÊ
ÃiiVÌ
The “É” key for T2 input selects K-type or J-type
thermocouple as input, when the second display has T2
shown. When the thermometer is turned on, it is set to
the type selected when the thermometer was last turned
off.
ºÉÊ/-»Ê`iÊÞÊ>Ê`ë>Þ®
Press “ÉÊ/-” key to enter the Hi/Lo Limits
comparative mode, “ ” is displayed. When the input
temperature value exceeds the Hi or Lo Limits value, the
beeper emits a continuous or pulsed tone. Press “ÉÊ
/-” key again to exit the Hi/Lo Limits mode.
7ÀiiÃÃÊ`iÊ/xÎ7®
Press the “ ” key for more than two seconds to start
wireless function. Press the “ ” key again for another
two seconds to stop wireless function. The wireless mode
will shut down if there is no wireless signal for two
minutes.
9
To SET CH/ID to 00,00, press the “ÉÊ/-” key and
” power key for more than 6 seconds with the meter
powered down. The meter will set channel and ID to
00,00 status. The second display will show 00, which
means that the channel and ID has been set to 00.
To check the channel and ID of the meter
7iÊÌiÊiÌiÀÊÃÊvv]Ê«ÀiÃÃʺcÉc” key and “ ” for 5
seconds, LCD’s main display will show channel number,
the second display will show ID number.
-*/"
iVÌÀV>Ê
/i«iÀ>ÌÕÀiÊ
-V>i
Celsius or Fahrenheit user-selectable
i>ÃÕÀiiÌÊ
,>}i
/Þ«iÊÓääcÊÌÊ£äxäc]
ÎÓncÊÌÊ£ÓÓc®
/Þ«iÊÓääcÊÌÊ£ÎÇäc]
ÎÓncÊÌÊÓ{nc®
,iÃÕÌ ä°£cÊÀÊä°Óc
VVÕÀ>VÞ Accuracy is specified for operating
Ìi«iÀ>ÌÕÀiÃÊÛiÀÊÌiÊÀ>}iÊvÊ£ncÊ
ÌÊÓncÊÈ{cÊÌÊnÓc®]ÊvÀÊ£ÊÞi>À]ÊÌÊ
including thermocouple error.
´ä°äx¯À`}³ä°Îc®ÊÊxäcÊÌÊ£ÎÇäc
´ä°äx¯À`}³ä°Çc®ÊÊxäcÊÌÊÓääc
´ä°äx¯À`}³ä°Èc®ÊÊxncÊÌÊÓ{nc
´ä°äx¯À`}³£°{c®ÊÊxncÊÌÊÎÓnc
/i«iÀ>ÌÕÀiÊ
ivwViÌ
0.1 times the applicable accuracy
ëiVwV>ÌÊ«iÀÊcÊvÀÊäcÊÌÊ£ncÊ
>`ÊÓncÊÌÊxäc
ÎÓcÊÌÊÈ{cÊ>`ÊnÓcÊÌÊ£ÓÓc®°
10
«ÕÌÊ*ÀÌiVÌ 24V dc or 24V ac rms maximum input
Voltage on any combination of input
pins.
«ÕÌÊiVÌÀ Accepts standard miniature
thermocouple connectors (flat blades
spaced 7.9mm, center to center).
>ÝÕÊvviÀiÌ>ÊÊ`iÊ6Ì>}i
>ÝÕÊ6Ì>}iÊLiÌÜiiÊ/£Ê>`Ê/ÓÊ`ÕÀ}Ê
i>ÃÕÀiiÌ®\Ê1 Volt.
ÛÀiÌ>
LiÌ
"«iÀ>Ì}Ê
,>}iÃ
äcÊÌÊxäcÊÎÓcÊÌÊ£ÓÓc®Ênä¯Ê,°°
-ÌÀ>}i
/i«iÀ>ÌÕÀi
ÓäcÊÌÊÈäcÊ{cÊÌÊ£{äc®ÊÇä¯Ê,°°
iiÀ>
ë>Þ 5 digit liquid crystal display (LCD).
"ÛiÀ>` °” or “"” is display..
,i>`}Ê,>Ìi 1 time per second.
ÕÌÊ«ÜiÀÊvv 30 minutes, press power key to
resume operation.
>ÌÌiÀÞ 4 X 1.5V AAA
>ÌÌiÀÞÊvi 190 hours typical with carbon zinc
battery.
iÃÃ 160mm(H) x 83mm(W) x 38mm(D); 6.3
in (H) x 3.3 in (W) x 1.5 in (D).
7i}Ì Approx. 270g (0.6lb) including
batteries.
11
-Õ««i`Ê7Ài 4 feet type “” thermocouple
bead wire (Teflon tape insulated).
Maximum insulation temperature
ÓÈäcÊxääc®°
7ÀiÊ>VVÕÀ>VÞÊ´Ó°ÓcÊÀÊ´ä°Çx¯ÊvÊ
reading (whichever is greater) from
äcÊÌÊnääcÊÎÓcÊÌÊ£{ÇÓc®°
7ÀiiÃÃÊi>ÌÕÀ
Frequency range 910~920MHz (TMD-53W)
Low current consumption less than 1mA.
The transmitting distance can reach 25M without
magnetic interference.
3 - \ Conforms to EN61326-1.
This product complies with requirements of the
following European Community Directives: 89/ 336/
EEC (Electromagnetic Compatibility) and 73/ 23/ EEC
(Low Voltage) as amended by 93/ 68/ EEC (CE Marking).
However, electrical noise or intense electromagnetic
fields in the vicinity of the equipment may disturb the
measurement circuit. Measuring instruments will also
respond to unwanted signals that may be present within
the measurement circuit. Users should exercise care and
take appropriate precautions to avoid misleading results
when making measurements in the presence of electronic
interference.
 /  Ê Ê,*,
:WARNING
/Ê>Û`Ê«ÃÃLiÊiiVÌÀV>ÊÃV]Ê`ÃViVÌÊÌiÊ
ÌiÀVÕ«iÊViVÌÀÃÊvÀÊÌiÊÌiÀiÌiÀÊ
LivÀiÊÀiÛ}ÊÌiÊVÛiÀ°
ÃÌ>}Ê>`Ê,i«>V}Ê>ÌÌiÀÞ
12
A. Screw
B. Battery Cover
C. Battery
1. Power is supplied by 4pcs 1.5V (SIZE AAA) UM-4
R03.
2. The “ ” appears on the LCD display when
replacement is needed. To replace battery remove
screw from back of meter and lift off the battery
cover.
3. Remove the batteries from the battery
compartment and replace them with new ones.
4. When not use for long time, remove the battery.
5. Do not store the unit in place with temperature
and humidity beyond the recommended storage
temperature.
i>}
Periodically wipe the case with a damp cloth and
detergent, do not use abrasives or solvents.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92

Amprobe AM-TMD53 Manuale del proprietario

Categoria
Misurazione
Tipo
Manuale del proprietario