ProLights LED Fresnel Manuale utente

Marca: ProLights

Modello: LED Fresnel

Categoria: Stroboscopi

Tipo: Manuale utente

EN - IT

USER MANUAL

MANUALE UTENTE

FRESNEL PROIECTOR

MINIECLFRTU-DY

reproduced in any form or by any means for any commercial use.

In order to improve the quality of products, Music&Lights S.r.l. reserves the right to modify the

characteristics stated in this instruction manual at any time and without prior notice.

All revisions and updates are available in the ‘manuals’ section on site www.musiclights.it

REV.001-09/18

MINIECLFRTU - DY

Packing content

• MINIECLFRTU-DY

• Barn doors

• Gel frame

• User manual

TABLE OF CONTENTS

Safety

General instructionsGeneral instructions

Warnings and installation precautionsWarnings and installation precautions

1 Technical drawing

1. 1 Operating elements and connections1. 1 Operating elements and connections

2 Installation

2. 1 Mounting2. 1 Mounting

3 Functions and settings

3. 1 Operation3. 1 Operation

3. 2 Basic3. 2 Basic

3. 3 Menu structure3. 3 Menu structure

3. 4 DMX mode3. 4 DMX mode

3. 5 DMX conguration3. 5 DMX conguration

3. 6 Screen3. 6 Screen

3. 7 Dimmer mode3. 7 Dimmer mode

3. 8 Led frequency3. 8 Led frequency

3. 9 Factory Reload3. 9 Factory Reload

3. 10 Fixture Information3. 10 Fixture Information

3. 11 Maste/Slave3. 11 Maste/Slave

3. 12 Eects3. 12 Eects

3. 13 Static3. 13 Static

3. 14 Connection of the DMX line3. 14 Connection of the DMX line

3. 15 Construction of the DMX termination3. 15 Construction of the DMX termination

3. 16 Channels DMX3. 16 Channels DMX

4 Maintenance

4. 1 Maintenance and cleaning the unit4. 1 Maintenance and cleaning the unit

4. 2 Fuse replacement4. 2 Fuse replacement

4. 3 Trouble shooting4. 3 Trouble shooting

MINIECLFRTU - DY

SAFETY

General instruction

• The products referred to in this manual conform to the European Community Directives and are there-

fore marked with .

• The unit is supplied with hazardous network voltage (230V~). Leave servicing to skilled personnel only.

Never make any modications on the unit not described in this instruction manual, otherwise you will

risk an electric shock.

• Connection must be made to a power supply system tted with ecient earthing (Class I appliance ac-

cording to standard EN 60598-1). It is, moreover, recommended to protect the supply lines of the units

from indirect contact and/or shorting to earth by using appropriately sized residual current devices.

• The connection to the main network of electric distribution must be carried out by a qualied electrical

installer. Check that the main frequency and voltage correspond to those for which the unit is designed

as given on the electrical data label.

• This unit is not for home use, only professional applications.

• Never use the xture under the following conditions:

- in places subject to vibrations or bumps;

- in places with a temperature of over 45 °C.

• Make certain that no inammable liquids, water or metal objects enter the xture.

• Do not dismantle or modify the xture.

• All work must always be carried out by qualied technical personnel. Contact the nearest sales point for

an inspection or contact the manufacturer directly.

• If the unit is to be put out of operation denitively, take it to a local recycling

plant for a disposal which is not harmful to the environment.

Warnings and installation precautions

• If this device will be operated in any way dierent to the one described in this manual, it may suer

damage and the guarantee becomes void. Furthermore, any other operation may lead to dangers like

short circuit, burns, electric shock, etc.

• Before starting any maintenance work or cleaning the projector, cut o power from the main supply.

• Always additionally secure the projector with the safety rope. When carrying out any work, always com-

ply scrupulously with all the regulations (particularly regarding safety) currently in force in the country

in which the xture’s being used.

• Install the xture in a well ventilated place.

• Keep any inammable material at a safe distance from the xture.

• Shields, lenses or ultraviolet screens shall be changed if they have become damaged to such an extent

that their eectiveness is impaired.

• The lamp (LED) shall be changed if it has become damaged or thermally deformed.

• Never look directly at the light beam. Please note that fast changes in lighting, e. g. ashing light, may

trigger epileptic seizures in photosensitive persons or persons with epilepsy.

• Do not touch the product’s housing when operating because it may be very hot.

• This product was designed and built strictly for the use indicated in this documentation. Any other use,

not expressly indicated here, could compromise the good condition/operation of the product and/or

be a source of danger.

• We decline any liability deriving from improper use of the product.

WARNING! Before carrying out any operations with the unit, carefully read this instruction

manual and keep it with cure for future reference. It contains important information about

the installation, usage and maintenance of the unit.

MINIECLFRTU - DY

- 1 - TECHNICAL DRAWING

Fig.1 - Technical drawing

Fig.2

MINIECLFRTU - DY

1.1 OPERATING ELEMENTS AND CONNECTIONS

1. AIR OPENING

2. LOCKING KNOB for mounting bracket

3. MOUNTING BRACKET

4. BARNDOOR HOLDER for insertion and locking

barn door

5. Rotary knob for manual focus

6. CONTROL PANEL with display and rotary knob

used to access the control panel functions

and manage them

7. MAIN FUSE HOLDER: replace a burnt-out fuse

by one of the same type only

8. Cable exible with 16A Shuko plug for con-

nection to a socket (100-240V~/50-60Hz)

9. Cable exible composed of a DMX IN (5-pole

XLR): 1 = ground, 2 = DMX-, 3 = DMX+, 4 N/C,

5 N/C and DMX OUT (5-pole XLR): 1 = ground,

2 = DMX-, 3 = DMX+, 4 N/C, 5 N/C

Fig.3

MINIECLFRTU - DY

- 2 - INSTALLATION

2.1 MOUNTING

MINIECLFRTU-DY is designed for applications in exhibition areas, commercial spaces, museums, restau-

rant, churches, and any other installation where size is an important factor. For xing, stable mounting

clips are required. The mounting place must be of sucient stability and be able to support a weight of

10 times of the unit’s weight.

When carrying out any installation, always comply scrupulously with all the regulations (particularly re-

garding safety) currently in force in the country in which the xture’s being used.

• Install the projector at a suitable location.

• Always additionally secure the projector with the safety rope from falling down. For this purpose, fas-

ten the safety rope at a suitable position so that the maximum fall of the projector will be 20 cm. The

adjust the projector and use the knobs.

NOTE - For the installation of the MINIECLFRTU-DY make sure that the ridge of the adaptor is in with the

groove of the track. Turn knobs 90° to connect the adaptor to the circuit.

MINIECLFRTU - DY

- 3 - FUNCTIONS AND SETTINGS

3.1 OPERATION

To turn on the MINIECLFRTU-DY connect the supplied main cable to a socket (100-240 VAC-50/60 Hz).

Then the unit is ready for operation.

To switch o, disconnect the mains plug from the socket. For a more convenient operation it is recom-

mended to connect the unit to a socket which can be switched on and o via a light switch.

ATTENTION - Mains voltage must be switched o before mounting; maintenance; insert and replace

Adaptors; spots and luminaires.

3.2 BASIC

Access control panel functions using the rotary knob located directly on the left the LED Display (g.5).

Fig.4- Functions of the buttons

1 CONNECT

DMX Address

(001-512)

DMX Mode

EASY-1Ch

BASIC-2Ch 1

BASIC-2Ch 2

BASIC-3Ch

STANDARD–5CH

2 SETUP

Screen

Back Light

10S

20S

30S

Flip Display

NO-Yes

3 ADVANCED

Dimmer Mode

O

Dimmer 1

Dimmer 2

Dimmer 3

Led Frequency

600Hz

1200 Hz

2000 Hz

4000 Hz

6000Hz

25kHZ

Factory Reload

NO-Yes

4 INFORMATION

Fixture Hours

0-9999

Version

V1.0

Temperature

°C

UID

15D00223****

5 STAND ALONE

Master/Slave

Master

Slave

Eect

Eect 1

Eect 2

Eect 3

Eect 4

Static

Dimmer

Strobe

MINIECLFRTU - DY

3.3 MENU STRUCTURE

MINIECLFRTU - DY

3.4 DMX MODE

• Press rotary knob to access the main menu.

• Rotate knob to scroll the menu, select Connect, then press the rotary knob to enter the next menu.

• Press on UP / DOWN to select DMX ADDRESS, and press the rotary knob to conrm.

• Rotate knob and press on UP/DOWN to select the desired value (001-512).

• Press rotary knob to store.

• Rotate knob and press on ← to go back or to meet the waiting time to exit the setup menu.

To able to operate the MINIECLFRTU-DY with a light controller, adjust the DMX start address for the rst a

DMX channel. If e. g. address 33 on the controller is provided for controlling the function of the rst DMX

channel, adjust the start address 33 on the MINIECLFRTU-DY. The other functions of the light eect panel

are then automatically assigned to the following addresses.

An example with the start address 33 is shown below:

3.5 DMX CONFIGURATION

MINIECLFRTU-DY is equipped with dierent DMX conguration.

• Press rotary knob to access the main menu.

• Rotate knob to scroll the menu, select Connect, then press the rotary knob to enter the next menu.

• Rotate knob to select DMX MODE, and press the rotary knob to conrm.

• Select the desired DMX conguration (EASY-1Ch, BASIC-2Ch 1, BASIC-2Ch 2, BASIC-3Ch, STANDARD–5CH) through

the rotary knob.

The tables on page 13 indicate the operating mode and DMX value.

3.6 SCREEN

You can change the following parameters related to the display, following the same procedure:

• Press rotary knob to access the main menu.

• Rotate knob to scroll the menu, select Set Up, then press the rotary knob to enter the next menu.

• Rotate knob to scroll through the menu, then select Screen, and press the rotary knob to enter the next

menu.

• Rotate knob to scroll through the menu, and then select one of the following settings for the display

and press the rotary knob to display it.

- Back Light - Backlight display Auto O. This feature allows you to automatically turn o the backlight

after a specied time that you can set using the arrow buttons. To have the display always on select

On or choose another value to turn o the display after the amount of time you choose.

- Flip Display - Orientation of the display. This function allows you to rotate the display 180° to get a

better view of the display when the unit is hanging upside down. Select YES to activate or NO to dis-

able this function.

• Press the rotary knob to conrm your choice.

• Rotate knob and press on ← to go back or to meet the waiting time to exit the setup menu.

Numero

canali DMX

Indirizzo di

start (esempio)

Indirizzo DMX

occupati

Prossimo indirizzo di start

possibile per unità n°1

Prossimo indirizzo di start

possibile per unità n°2

Prossimo indirizzo di start

possibile per unità n°3

5 33 33 - 37 38 43 48

MINIECLFRTU - DY

3.7 DIMMER MODE

Enter in Dimmer mode to select specic dimming curve, press the rotary knob to access the main menu.

• Rotate knob to scroll the menu, select Advanced, then press the rotary knob to enter the next menu.

• Rotate knob to scroll through the menu, then select Dimmer mode, and press the rotary knob to conrm.

• Rotate knob to select O - Dimmer1 - Dimmer2 - Dimmer3.

• Press the rotary knob to conrm your choice.

• Rotate knob and press on ← to go back or to meet the waiting time to exit the setup menu.

3.8 LED FREQUENCY

To adjust the frequency of the LEDs, press the rotary knob to access the main menu.

• Rotate knob to scroll the menu, select Advanced, then press the ENTER button to enter the next menu.

• Rotate knob to scroll through the menu, then select LED Frequency, and press the button ENTER to con-

rm.

• Select the frequency (600Hz - 1200Hz - 2000Hz - 4000Hz - 6000Hz - 25kHz) using the rotary knob buttons.

• To conrm, press the rotary knob.

• Rotate knob and press on ← to go back or to meet the waiting time to exit the setup menu.

3.9 FACTORY RELOAD

Select this function to reset the unit to the factory settings:

• To activate Reset Factory display press the rotary knob to access the main menu.

• Rotate knob to scroll the menu, select Advanced, then press the rotary knob to enter the next menu.

• Rotate knob to scroll through the menu, then select Factory Reload, and press the rotary knob to conrm.

• Rotate knob and press on ← to go back or to meet the waiting time to exit the setup menu.

3.10 FIXTURE INFORMATION

To view all the information on the device, proceed as follows:

• Press the rotary knob to access the main menu.

• Rotate knob button to scroll the menu, select Information, then press the rotary knob to enter the next

menu.

• Rotate knob button to scroll through the menu, then select one of the following information and press

the rotary knob to display it.

- Fixture Time - Through the Fixture Time function you can display the operating time of the projector.

- Software Version - Through Temperature function you can display the temperature of the device.

- Temperature - Through Temperature function you can display the temperature of the device.

- UID - This option shows the RDM identication number.

• Rotate knob and press on ← to go back or to meet the waiting time to exit the setup menu.

3.11 MASTER SLAVE

Press the rotary knob button to access the main menu.

• Rotate knob button to scroll the menu, select Stand Alone, then press the rotary knob to enter the next

menu.

• Rotate knob button to scroll through the menu, select Master/Slave and press the rotary knob to conrm

your choice.

• Rotate knob button to select the mode of operation:

- Master, if the unit is connected in series with other units and it acts as the Master;

- Slave, if the unit is not connected to other units.

MINIECLFRTU - DY

• Press the rotary knob to conrm your choice.

• Rotate knob and press on ← to go back or to meet the waiting time to exit the setup menu.

3.12 EFFECTS

The unit has pre-programmed eects that can be set through the following procedure:

• Press the rotary knob to access the main menu.

• Rotate knob button to scroll the menu, select Eects, then press the rotary knob to enter the next menu.

• Rotate knob button to select the mode of operation: Eects 1, Eects 2, Eects 3, Eects 4.

• Press the rotary knob to conrm your choice.

• Rotate knob and press on ← to go back or to meet the waiting time to exit the setup menu.

3.13 STATIC

The unit allows you to create congurations that can be set through the following procedure:

• To enter to static static mode, press the rotary knob to access the main menu.

• Rotate knob button to scroll the menu, select Stand Alone, then press the rotary knob to enter the next

menu.

• Rotate knob button to scroll through the menu, select Static and press rotary knob to conrm your

choice.

• Throught the rotary knob select Dimmer o Strobe and press the rotary knob to conrm the desired func-

tion.

• Set the value (000 - 255), Throught the rotary knob, then press it to conrm

• Rotate knob and press on ← to go back or to meet the waiting time to exit the setup menu.

NOTE: once the plug of the power cord has been connected to a power outlet, to access the Dimmer mode

directly, simply press the knob twice consecutively. After that, choiche the desired value.

NOTE: once the projector is connected to a power outlet, to directly access the Dimmer mode, simply dou-

ble click on the knob, rotating it. After that, choiche the desired value.

MINIECLFRTU - DY

Fig.5

Fig.6

3.14 CONNECTION OF THE DMX LINE

DMX connection employs standard XLR connectors. Use shielded pair-twisted cables with 120Ω imped-

ance and low capacity.

The following diagram shows the connection mode:

ATTENTION

The screened parts of the cable (sleeve) must never be connected to the system’s earth, as this would

cause faulty xture and controller operation.

Over long runs can be necessary to insert a DMX level matching amplier.

For those connections the use of balanced microphone cable is not recommended because it cannot

transmit control DMX data reliably.

• Connect the controller DMX input to the DMX output of the rst unit.

• Connect the DMX output to the DMX input of the following unit. Connect again the output to the input

of the following unit until all the units are connected in chain.

• When the signal cable has to run longer distance is recommended to insert a DMX termination on the

last unit.

3.15 CONSTRUCTION OF THE DMX TERMINATION

The termination avoids the risk of DMX 512 signals being reected back along the cable when they reach-

es the end of the line: under certain conditions and with certain cable lengths, this could cause them to

cancel the original signals.

The termination is prepared by soldering a 120Ω 1/4 W resistor between pins 2 and 3 of the 5-pin male XLR

connector, as shown in gure.

DMX - OUTPUT

XLR socket

DMX - INPUT

XLR plug

Pin1 : GND - Shield

Pin2 : - Negative

Pin3 : + Positive

Pin4 : N/C

Pin5 : N/C

Example:

5 pin XLR connector

1 CHANNEL

MODE

FUNCTION DMX

Value

1 Ch

DIMMER

0~100% 000 - 255

5 CHANNELS

MODE

FUNCTION DMX

Value

5 Ch

DIMMER

0~100% 000 - 255

STROBE

No Function

Strobe slow to fast

000 - 010

011 - 255

AUTO PROGRAMS

No Function

Auto Program 1

Auto Program 2

Auto Program 3

Auto Program 4

000 - 010

011 - 070

071 - 130

131 - 190

191 - 255

AUTO SPEED

Speed slow to fast 000 - 255

DIMMER SPEED MODE

Preset dimmer speed from display menu

Dimmer speed mode o

Dimmer speed mode1 (fast speed)

Dimmer speed mode2 (middle speed)

Dimmer speed mode3 (slow speed)

000 - 051

052 - 101

102 - 152

153 - 203

204 - 255

3 CHANNELS

MODE

FUNCTION DMX

Value

3 Ch

DIMMER

0~100% 000 - 255

DIMMER FINE

0~100% 000 - 255

STROBE

No Function

Strobe slow to fast

000 - 010

011 - 255

2 CHANNELS 1

MODE

FUNCTION DMX

Value

2 Ch1

DIMMER

0~100% 000 - 255

DIMMER FINE

0~100% 000 - 255

2 CHANNELS 2

MODE

FUNCTION DMX

Value

2 Ch2

DIMMER

0~100% 000 - 255

STROBE

No Function

Strobe Slow to Fast

000 - 010

011 - 255

MINIECLFRTU - DY

3.16 CHANNELS DMX

MINIECLFRTU - DY

- 4 - MAINTENANCE

4.1 MAINTENANCE AND CLEANING THE UNIT

• Make sure the area below the installation place is free from unwanted persons during setup.

• Switch o the unit, unplug the main cable and wait until the unit has cooled down.

• All screws used for installing the device and any of its parts should be tightly fastened and should not

be corroded.

• Housings, xations and installation spots (ceiling, trusses, suspensions) should be totally free from any

deformation.

• The main cables must be in impeccable condition and should be replaced immediately even when a

small problem is detected.

• It is recommended to clean the front at regular intervals, from impurities caused by dust, smoke, or

other particles to ensure that the light is radiated at maximum brightness. For cleaning, disconnect the

main plug from the socket. Use a soft, clean cloth moistened with a mild detergent. Then carefully wipe

the part dry. For cleaning other housing parts use only a soft, clean cloth. Never use a liquid, it might

penetrate the unit and cause damage to it.

•

4.2 FUSE REPLACEMENT

1. Disconnect this product from the power outlet.

2. Using a screwdriver, unscrew the fuse holder cap from the housing.

3. Remove the blown fuse and replace with a good fuse of the same type and rating.

4. Screw the fuse holder cap back in place and reconnect power

Fig.7

MINIECLFRTU - DY

Problems Possible causes Checks and remedies

Fixture does not light up

• No mains supply

• Dimmer fader set to 0

• Faulty LED

• Check the power supply voltage

• Increase the value of the dimmer channels

• Replace the LED board

General low light intensity

• Dirty lens assembly

• Misaligned lens assembly

• Clean the xture regularly

• Install lens assembly properly

Fixture does not power up

• No power

• Loose or damaged power cord

• Check for power on power outlet

• Check power cord

Contact an authorized service center in case of technical problems or not reported in the table can not be

resolved by the procedure given in the table.

4.3 TROUBLESHOOTING

REV.001-09/18

Music & Lights S.r.l. si riserva ogni diritto di elaborazione in qualsiasi forma delle presenti istruzioni per l’uso.

La riproduzione - anche parziale - per propri scopi commerciali è vietata.

Al ne di migliorare la qualità dei prodotti, la Music&Lights S.r.l. si riserva la facoltà di modicare, in

qualunque momento e senza preavviso, le speciche menzionate nel presente manuale di istruzioni.

Tutte le revisioni e gli aggiornamenti sono disponibili nella sezione 'Manuali' sul sito www.musiclights.it

MINIECLFRTU - DY

• MINIECLFRTU-DY

• Barb doors

• Gel frame

• Manuale utente

Contenuto dell'imballo:

INDICE

Sicurezza

Avvertenze generaliAvvertenze generali

Attenzioni e precauzioni per l’installazioneAttenzioni e precauzioni per l’installazione

1 Disegno tecnico

1. 1 Elementi di comando e di collegamento 1. 1 Elementi di comando e di collegamento

2 Installazione

2. 1 Montaggio2. 1 Montaggio

3 Funzioni e impostazioni

3. 1 Funzionamento3. 1 Funzionamento

3. 2 Impostazione base3. 2 Impostazione base

3. 3 Struttura menù3. 3 Struttura menù

3. 4 Modalità DMX3. 4 Modalità DMX

3. 5 Congurazione canali3. 5 Congurazione canali

3. 6 Screen3. 6 Screen

3. 7 Dimmer mode3. 7 Dimmer mode

3. 8 Frequenza led3. 8 Frequenza led

3. 9 Factory Reload3. 9 Factory Reload

3. 10 Informazioni sul dispositivo3. 10 Informazioni sul dispositivo

3. 11 Master/Slave3. 11 Master/Slave

3. 12 Eects3. 12 Eects

3. 13 Static3. 13 Static

3. 14 Collegamenti della linea DMX3. 14 Collegamenti della linea DMX

3. 15 Costruzione del terminatore DMX3. 15 Costruzione del terminatore DMX

3. 16 Canali DMX3. 16 Canali DMX

4 Manutenzione

4. 1 Manutenzione e pulizia del sistema ottico4. 1 Manutenzione e pulizia del sistema ottico

4. 2 Sostituzione fusibile4. 2 Sostituzione fusibile

4. 3 Risoluzione dei problemi4. 3 Risoluzione dei problemi

MINIECLFRTU - DY

ATTENZIONE! Prima di effettuare qualsiasi operazione con l’unità, leggere con attenzione

questo manuale e conservarlo accuratamente per riferimenti futuri. Contiene informazioni

importanti riguardo l’installazione, l’uso e la manutenzione dell’unità.

SICUREZZA

Avvertenze generali

• I prodotti a cui questo manuale si riferisce sono conformi alle Direttive della Comunità Europea e per-

tanto recano la sigla .

• Il dispositivo funziona con pericolosa tensione di rete 230V~. Non intervenire mai al suo interno al di

fuori delle operazioni descritte nel presente manuale; esiste il pericolo di una scarica elettrica.

• È obbligatorio eettuare il collegamento ad un impianto di alimentazione dotato di un’eciente messa

a terra (apparecchio di Classe I secondo norma EN 60598-1). Si raccomanda, inoltre, di proteggere le

linee di alimentazione delle unità dai contatti indiretti e/o cortocircuiti verso massa tramite l’uso di

interruttori dierenziali opportunamente dimensionati.

• Le operazioni di collegamento alla rete di distribuzione dell’energia elettrica devono essere eettuate

da un installatore elettrico qualicato. Vericare che frequenza e tensione della rete corrispondono alla

frequenza ed alla tensione per cui l’unità è predisposta, indicate sulla targhetta dei dati elettrici.

• L’unità non per uso domestico, solo per uso professionale.

• Evitare di utilizzare l’unità:

- in luoghi soggetti a vibrazioni, o a possibili urti;

- in luoghi a temperatura superiore ai 45°C.

• Evitare che nell’unità penetrino liquidi inammabili, acqua o oggetti metallici.

• Non smontare e non apportare modiche all’unità.

• Tutti gli interventi devono essere sempre e solo eettuati da personale tecnico qualicato. Rivolgersi al

più vicino centro di assistenza tecnica autorizzato.

• Se si desidera eliminare il dispositivo denitivamente, consegnarlo

per lo smaltimento ad un’istituzione locale per il riciclaggio.

Attenzioni e precauzioni per l’installazione

• Se il dispositivo dovesse trovarsi ad operare in condizioni dierenti da quelle descritte nel presente

manuale, potrebbero vericarsi dei danni; in tal caso la garanzia verrebbe a decadere. Inoltre, ogni altra

operazione potrebbe provocare cortocircuiti, incendi, scosse elettriche, rotture etc.

• Prima di iniziare qualsiasi operazione di manutenzione o pulizia sull’unità togliere la tensione dalla rete

di alimentazione.

• È assolutamente necessario proteggere l’unità per mezzo di una fune di sicurezza. Nell’eseguire qualsi-

asi intervento attenersi scrupolosamente a tutte le normative (in materia di sicurezza) vigenti nel paese

di utilizzo.

• Installare l’unità in un luogo ben ventilato.

• Mantenere i materiali inammabili ad una distanza di sicurezza dall’unità.

• I ltri, le lenti o gli schermi ultravioletti se danneggiati possono limitare la loro ecienza.

• I LED devono essere sostituiti se danneggiati o termicamente deformati.

• Non guardare direttamente il fascio luminoso. Tenete presente che i veloci cambi di luce possono pro-

vocare attacchi d’epilessia presso persone fotosensibili o epilettiche.

• Non toccare l’alloggiamento del prodotto quando è in funzione perché potrebbe essere molto caldo.

• Questo prodotto è stato progettato e costruito esclusivamente per l’utilizzo indicato in questa docu-

mentazione. Qualsiasi altro utilizzo non espressamente indicato potrebbe pregiudicare la funzionalità

del prodotto e/o rappresentare fonte di pericolo.

• Si declina qualsiasi responsabilità derivata dall’uso improprio del prodotto.

La pagina sta caricando ...

ProLights LED Fresnel Manuale utente

Marca: ProLights

Modello: LED Fresnel

Categoria: Stroboscopi

Tipo: Manuale utente

Scarica il pdf

rapporto

in altre lingue

English: ProLights LED Fresnel User manual

ProLights LED Fresnel Manuale utente

ProLights LED Fresnel Manuale utente

in altre lingue

Documenti correlati