DTS DRIVENET 1664 Manuale utente

Tipo
Manuale utente
Technical DatasheetTechnical Datasheet
User
s Manual rel 1.0 GB
DRIVENET 1664
Le informazioni contenute in questo documento sono state attentamente redatte e controllate. Tuttavia
non è assunta alcuna responsabilità per eventuali inesattezze. Tutti i diritti sono riservati e questo
documento non può essere copiato, fotocopiato, riprodotto per intero o in parte senza previo consenso
scritto della D.T.S .
DTS si riserva il diritto di apportare senza preavviso cambiamenti e modifiche estetiche , funzionali o di
design a ciascun proprio prodotto. D.T.S non assume alcuna responsabilità sull’uso o sull’applicazione
dei prodotti o dei circuiti descritti.
The information contained in this publication has been carefully prepared and checked. However, no
responsibility will be taken for any errors. All rights are reserved and this document cannot be copied,
photocopied or reproduced, in part or completely, without prior written consent from D.T.S.
D.T.S. reserves the right to make any aesthetic, functional or design modifications to any of its products
without prior notice. D.T.S. assumes no responsibility for the use or application of the products or circuits
described herein.
Les informations contenues dans le présent manuel ont été rédigées et contrôlées avec le plus grand
soin. Nous déclinons toutefois toute responsabilité en cas d'éventuelles inexactitudes. Tous droits
réservés. Ce document ne peut être copié, photocopié ou reproduit, dans sa totalité ou partiellement,
sans le consentement préalable de .D.T.S
D.T.S. se réserve le droit d'apporter toutes modifications et améliorations esthétiques, fonctionnelles ou
de design, sans préavis, à chacun de ses produits. décline toute responsabilité sur l'utilisation ou D.T.S.
sur l'application des produits ou des circuits décrits.
Las informaciones contenidas en este documento han sido cuidadosamenteredactadas y
controladas. Con todo, no se asume ninguna responsabilidad por eventuales inexactitudes.
Todos los derechos han sido reservados y este documento no puede ser copiado, fotocopiado
o reproducido, total o parcialmente, sin previa autorizaciónescrita de D.T.S.
D.T.S. se reserva el derecho a aportar sin previo aviso cambios y modificaciones de carácter
estético, funcional o de diseño a cada producto suyo. no se asume responsabilidad de D.T.S.
ningún tipo sobre la utilización o sobre la aplicació
n de los productos o de los circuitos descritos.
DRIVENET 1664
2
TECHNICAL SPECIFICATIONS
DTS Product codes:
03.LA.198 DRIVENET 1664 Screw terminal outputs
Input voltage/frequency range: 180-240Vac 50-60Hz (Voltage not compatible in: USA, Canada,
Mexico, Venezuela, Colombia, Ecuador, Central America and Carribean area, Japan, Taiwan, Libia)
Output channels: 64 (4 channels x 16 groups)
Output current: 700mA max (per channel)
Ouput voltage: 48Vdc
Max power: 2200W
Max projectors distance: 50 m
Output connections: Screw terminal connectors
Mains connections: PowerCON male panel connector
DMX connections: XLR 5-pole and 3-pole panel connectors
Display: Touch-screen color display
Control: DMX 512 / RDM / Art-Net (optional)
DMX channels: 64 (default), 128 ch, 10 ch, 14 ch, 160 ch, 224 ch, 96 ch, 1 ch
IP protection degree: IP20
Operating temperature: -10° / 40°
Rack units: 3-rack units
Weight: 11.4 Kg
International certifications
CE certification
Accessories included
1 x PowerCON female cable connector (code 0520P014)
1 x XLR 5 pins male cable connector (code 0508B148)
1 x XLR 5 pins female cable connector (code 0508B147)
Accessories on request
Art-Net interface PCB (code 0514T027)
DTS Dongle Firmware Uploader (code 03.LA.206)
3
DRIVENET 1664
DIMENSIONS
4
DRIVENET 1664
IMPORTANT SAFETY INFORMATION
Fire prevention:
It is permissible to place the unit on normally flammable surfaces.
Suitable for mounting on normally flammable materials surfaces greater than 200°C with some
combustion time lag.
Replace any blown or damaged fuse only with one of identical value (15AT).
Prevention from electric shock:
High voltage is present inside the unit.
Unplug the unit prior to performing any operation which involves touching the inside of the unit.
This equipment must be grounded, do not connect to non-grounded supplies.
The use of a thermal magnetic circuit breaker is recommended for each DRIVENET 1664.
Use only AC supplies 180-240V 50-60Hz (Voltage not compatible in: USA, Canada, Mexico, Venezuela,
Colombia, Ecuador, Central America and Carribean area, Japan, Taiwan, Libia).
The unit should never be located in position exposed to rain or in areas of extreme humidity.
A good air ventilation is essential for proper equipment work.
Safety:
Never install the unit in an enclosed area lacking sufficient air flow.
The ambient temperature should not exceed 40°C and should not be lower than -10°C.
CONNECTIONS PANEL
5
MAINS IN
180-240Vac 50-60 Hz*
PowerCON male
panel connector
FUSE
15AT
Art-Net IN
RJ45 female
panel connector
(optional)
DMX IN / OUT
XLR 5-pole and 3-pole
panel connectors
16 LED OUTPUTS
8-pole screw terminal connectors
1 2 3 4
5 6 7 8
9 10 11 12
13 14 15 16
* Voltage not compatible in: USA, Canada, Mexico, Venezuela, Colombia, Ecuador, Central America and
Carribean area, Japan, Taiwan, Libia.
DRIVENET 1664
DMX SIGNAL CONNECTION:
The unit operates using a digital DMX 512 signal. Connection between the controller and the unit or
between units must be carried out using a two pair screened ø 0.5 mm cable and a CANNON XLR 5 pins
connector.
Ensure that the conductors do not touch each other. Do not connect the cable ground to the XLR
chassis. The plug housing must be isolated. Connect the mixer signal to the DMX IN of the Z8 plug and
connect it to the next unit by connecting the DMX OUT plug on the first Z8 to the DMX IN plug of the
second one.
This way, all the projectors are cascade connected.
P.S: If the display showing the DMX address flashes, then one of the following errors has occurred:
- DMX signal not present
- DMX reception problem
For Installations where long distance DMX cable connections are needed, we suggest to use a DMX
terminator.
The DMX terminator is a male XLR 3-5 pins connector with a 120 ohm resistor Between pin 2 and 3.
The DMX terminator must be plugged into the last unit (DMX out panel connector) of the DMX line.
1
2
3
5
4
OUT
120 ohm
PIN 3
PIN 2
PLACE A 120 OHM RESISTOR BETWEEN PIN 2
AND 3 OF A MALE XRL CONNECTOR AND PLUG IT
INTO THE DMX OUT PANEL CONNECTOR OF THE
LAST UNIT CONNECTED TO THE DMX LINE
6
Standard
DMX 512
controller
5
3
4 2
1
1=GND
2=DATA-
3=DATA+
OUT
IN
OUT
IN
OUT
DRIVENET 1664
DMX ADDRESS
DRIVENET 1664 can be used in 9 DMX modes: 64 ch (default), 128 ch, 10 ch, 14 ch, 160 ch,
224 ch, 96 ch or 1 ch mode.
If you want to use the DRIVENET 1664 in 64 channels mode, select the “ ” mode Full Type 8 bit 64ch
from the DMX MODE menu under DMX SETUP and set the following addresses on the mixer:
Projector 1 A001
Projector 2 A065 If you want to select the next projector, just add “64”
Projector 3 A129
….. A….
projector 6 A321
If you want to use the DRIVENET 1664 in 10 channels mode, select the “ 10ch” mode Z1 Type 8 bit
from the DMX MODE menu under DMX SETUP and set the following addresses on the mixer:
Projector 1 A001
Projector 2 A011 If you want to select the next projector, just add “10”
Projector 3 A021
….. A….
projector 6 A051
Selecting the DMX address
1) Press the UP-DOWN key until you reach the required DMX address. The numbers on the display will
start flashing (but the new DMX address hasn't yet been set).
2) Press ENTER to confirm your selection. The numbers on the display will stop flashing and the
projector is now controlled by the new DMX address.
TIPS: if you keep pushed the UP or DOWN keys, the channels are calculated more quickly and you get a
faster selection.
7
DRIVENET 1664
RDM FUNCTIONS
DRIVENET 1664 do accept the following RDM commands:
8
DRIVENET 1664
NOTE: Between Identify ON and Identify OFF packets, the DMX is Ignored.
When “INDEPENDENT UNIT ADDRESS” is eneabled on unit display, the RDM controller
do have access to DMX of the first output group.
FIRMWARE UPDATING
DRIVENET 1664To update the firmware release of the you need:
- DTS Dongle Firmware Uploader (code 03.LA.206).
- “DTS Firmware Upgrade Utility v.2.02” program installed on PC.
- Latest firmware release available for unit.DRIVENET 1664
Updating the firmware release.
Please follow the procedure below to perform the update:
1. Connect the DTS Dongle Firmware Uploader to a spare USB port on the PC.
2. Connect the unit DMX input to the DTS Dongle Firmware Uploader DMX output with a
standard DMX cable and turn ON the unit.
3. Send the new firmware release into the unit by using “DTS Firmware Upgrade
Utility v.2.02” program. At the end of the procedure, the unit will reset.
For more information please refer to an authorised DTS service centre.
MENU
DISPLAY
ENTER
DOWN
UP
MENU
ENTER
DOWN
UP
A001
DISPLAY FUNCTIONS
ENTER
DOWN
UP
MENU
DISPLAY FUNCTIONS
The DRIVENET 1664 24Vdc display panel shows all the available functions.
Using these functions, it is possible to change some of the parameters and add some functions.
Changing the DTS setting can vary the functions of the unit so that it does not respond to the DMX 512
signal used to control it.
Carefully follow the instructions below before carrying out any variations or selections.
NOTE: the symbol shows which key has to be pushed to obtain the desired function.
FIRMWARE RELEASE: 1.19
RDM Device Model ID: 0x0D21/2E
DMX Personality ID (default): 0x01 “FULL TYPE 8 BIT 64 ch”
9
TOUCH-SCREEN
COLOR DISPLAY
POSITION
AA
Menu
DISPLAY POSITION
Reverses display's reading depending on
the mounting position
(on the ground or suspended).
DISPLAY STANDBY
To turn off the display (after 30 seconds) or
Leave it always on.
Up-Down
Display
ENTER Up-Down
DISPLAY POSITION
ON THE GROUND (Default)
SUSPENDED
DISPLAY STANDBY
OFF = Display standby disabled (default)
ON = Display goes off after 30 seconds
ENTER
ENTER
ARTNET 512CH
UNIVERSE #001
DRIVENET 1664
DMX Setup
DMX MODE MAP
Full Type 8 bit 64ch = 64 DMX ch (default)
= RGBW 4 ch each output: 1-Red, 2-Green, 3-
Blue, 4-White.
Full Type 16 bit 128ch = 128 DMX ch mode
= RGBW 2 ch each colour; 8 ch each output:
1-Red 8 bit, 2-Red 16 bit, 3-Green 8 bit,
4-Green 16 bit, 5-Blue 8 bit, 6-Blue 16 bit,
7-White 8 bit, 8-White 16 bit
Z1 Type 8 bit 10ch = 10 DMX ch mode with all
the outputs automatically set on DMX starting
channel 1:
1=Shutter, 2=Dimmer, 3=Red, 4=Green,
5=Blue, 6=White, 7=White pre-programmed,
8=CTC, 9=Macro, 10=Function
Z1 Type 16 bit 14ch = 14 DMX ch mode with
Dimmer and RGBW channels with 16 bit control
and all outputs automatically set on DMX
starting address 1:
1=Shutter, 2=Dimmer, 3=Red 8 bit, 4=Red 16
bit,5=Green 8 bit, 6=Green 16 bit, 7=Blue 8 bit,
8=Blue 16 bit, 9=White 8 bit, 10=White 16 bit,
11=White pre-programmed, 12=CTC, 13=Macro,
14=Function
Z1 Full 8 bit 160 ch = (10x16) 160 DMX ch
mode same as Z1 Type 8 bit 10ch but each
output with independent DMX control:
Output 1=DMX 1, Output 2= DMX 11, Output
3= DMX 21 ...
Z1 Full 16 bit 224ch = (14x16) 224 DMX ch
mode same as Z1 Type 16 bit 14ch but each
output with independent DMX control:
Output 1 = DMX 1, Output 2 = DMX 15,
Output 3 = DMX 29...
Z1 Short Full 8 bit 96ch = (6x16) 96 DMX ch
mode with Dimmer, Shutter and RGBW 8 bit
channels and each output with independent DMX
control
Output 1 = DMX 1, Output 2 = DMX 7,
Output 3 = DMX 13...
Z1 Short Full 16 bit 160ch = (10x16) 160
DMX ch mode with RGBW 16 bit each colour and
each output with independent DMX control
Output 1 = DMX 1, Output 2 = DMX 11,
Output 3 = DMX 21...
1-Dimmer, 2-Shutter, 3-Red 8 bit, 4-Red
16 bit, 5-Green 8 bit, 6-Green 16 bit,
7-Blue 8 bit, 8-Blue 16 bit, 9-White 8 bit,
10-White 16 bit
1ch Full Mode = 1 DMX channel
Menu
Up-Down
ENTER Up-Down
ENTER
DMX MODE
To select DMX mode:
Full Type 8 bit 64 ch
Full Type 16 bit 128 ch
Z1 Type 8 bit 10 ch
Z1 Type 16 bit 14 ch (for Chase and Cue
recording).
Z1 Full 8 bit 10x16 = 160 ch
Z1 Full 16 bit 14x16 = 224 ch
Z1 Short Full 8 bit 6x16 = 96 ch
Z1 Short Full 16 bit 10x16 = 160 ch
1 ch Full Mode = 1 ch
INDEPENDENT UNIT ADDRESS
Allows independent DMX patch each
group for the following DMX modes:
Full Type 8 bit 64 ch
Full Type 16 bit 128 ch
Z1 Full 8 bit 10x16 = 160 ch
Z1 Short Full 8 bit 6x16 = 96 ch
Z1 Short Full 16 bit 10x16 = 160 ch
Default = OFF
MACRO
Standard = default
Extended = enable rainbow effects on
MACRO channel
10
MENU
DMX SETUP
ENTER
DOWN
UP
DMX MODE
Full Type 8 bit 64ch
MENU
DMX SETUP
ENTER
DOWN
UP
MACRO
STANDARD
MENU
DMX SETUP
ENTER
DOWN
UP
INDEPENDENT UNIT ADDRS
OFF
DRIVENET 1664
LED
Menu
Up-Down
ENTER Up-Down
ENTER
RGBW MINIMUM VALUES
This menu allows to select the minimum
levels for Red/White1, Green/White2,
Blue/White3 and White/White4.
RGBW MAXIMUM VALUES
This menu allows to select the maximum
levels for Red/White1, Green/White2,
Blue/White3 and White/White4.
These settings have priority on Master
Dimmer channel.
SMOOTH VALUE
This menu allows to select the value of
the delay (in milliseconds) for RGBA and
Dimmer channels reaction to DMX or
program variation.
4 = 25 ms delay (Fast response)
20 = 250 ms delay (Slow response)
GAMMA CORRECTION
This menu allows to select between
Linear current output or Quadratic
current output for LEDs
Default = Quadratic
OUTPUT FREQUENCY
This menu allows to adjust the PWM
frequency value (Hz) in order to reduce
flickering in the process of your camera
Recordings
LED BOOST
With Boost ON, the LED’s current has the
same value pre-set into the “LED
CURRENTS” menu (see below).
With Boost OFF the medium current of
each output channel is approximately
30% less (through PWM modulation) of
the maximum current pre-set into the
“LED CURRENTS” menu.
11
MENU
LED
ENTER
DOWN
UP
RED MIN
0
MENU
LED
ENTER
DOWN
UP
RED MAX
100
MENU
LED
ENTER
DOWN
UP
SMOOTH
4
MENU
LED
ENTER
DOWN
UP
GAMMA CORRECTION
QUADRATIC
MENU
LED
ENTER
DOWN
UP
OUTPUT FREQUENCY
610 Hz
MENU
LED
ENTER
DOWN
UP
BOOST
ON
RED Min default = 0
RED Max default = 100
GREEN Min default = 0
GREEN Max default = 100
BLUE Min default = 0
BLUE Max default = 100
WHITE Min default = 0
WHITE Max default = 100
SMOOTH
Range = Off - 20
Default = 4
GAMMA CORRECTION
Linear = Linear current output
Quadratic = Linear light output (default)
OUTPUT FREQUENCY
Range = 610 Hz - 20 KHz
Default = 610 Hz
LED BOOST
ON-OFF
Default = OFF
LED CURRENTS
Menu
Up-Down
ENTER Up-Down
ENTER
MENU
LED CURRENTS
ENTER
DOWN
UP
ALL OUT CURRENTS
700 mA
ALL OUTPUT CHANNELS CURRENT
SELECTION
This menu allows to select the same
maximum LED current (peak) for all
output channels.
OUTPUT CHANNEL CURRENT SELECTION
This menu allows to select the maximum
LED current (peak) independently for
each output channel.
LED CURRENTS
Range = 200 mA - 700 mA (50mA by
50mA selectable steps)
Default = 700 mA
MENU
LED CURRENTS
ENTER
DOWN
UP
OUT 01 CURRENT
700 mA
DRIVENET 1664
AUTO
Menu
Up-Down
ENTER Up-Down
ENTER
AUTOMATIC MODE
Automatic demo game without DMX
controller
STEP 01/16
Chase with 16 steps previously created in
REC MODE
Speed time, Wait time and Dimmer
values selectable by user.
PERSONAL COLOURS
RGBA, Dimmer and Shutter values
selectable by user.
RAINBOW
Rainbow colours effect.
Speed time, Dimmer and Shutter values
Selectable by user.
FIXED COLOURS
Sixteen colour macros as on “MACRO”
channel.
Dimmer and Shutter values selectable by
user.
WHITE MACROS
Sixteen macros for White colour.
Dimmer and Shutter values selectable by
user.
12
MENU
AUTO
ENTER
DOWN
UP
SURE?
MENU: NO - ENTER: YES
MENU
AUTO-PROGRAM
ENTER
DOWN
UP
STEP
01/16
MENU
AUTO-PERS.COLORS
ENTER
DOWN
UP
RED
120
MENU
AUTO-RAINBOW
ENTER
DOWN
UP
SPEED
0006
MENU
AUTO-FIXED COLORS
ENTER
DOWN
UP
COLOR
9
MENU
AUTO-WHITE
ENTER
DOWN
UP
WHITE
1
By setting all the units connected to the
MASTER to DMX address 1, them will be
synchronized with the Master unit
following the chase selected on it,
including Time and Wait of the Master
unit.
DRIVENET 1664
13
Menu
REC MODE
In DMX Recorder mode it is possible
To create and store the scenes of the
CHPR menu by using an external DMX
controller.
DRIVENET is forced to Z1 Type 8 bit 10ch
mode.
Up-Down
REC
ENTER Up-Down
MENU
REC
ACTIVATE REC MODE
CHPR1,2,3=011,012,013
ENTER
DOWN
UP
ENTER
For the programming of ChPr by using a DMX controller, besides the 10 channels a further 3 DMX channels are needed.
So that in REC mode (via DMX) the unit will need 13 channels to be correctly programmed.
The three new DMX channels are:
DMX channel 11 = CHPR1
From 0-24 = no function
From 25-255 it is possibile to select one of the 16 programmable scenes
DMX channel 12 = CHPR2
From 0-19 it is shown the selected scene
From 20-234 the unit runs the configuration given by the received input DMX values.
With the channel CHPR2 it is possible to pass from one step to the next while with channel CHPR3 it is possible to record the
selected scene.
From 235-255 the unit runs the configuration given by the received input DMX values closing the sequence as last scene.
With the channel CHPR3 it is possible to record the selected scene as last scene.
DMX channel 13 = CHPR3
Records the scene with a variation between 0-128 to 129-255 (the display flashes indicating that the scene has been recorded).
It is advised that you keep the REC channel set to 0 and to run through the 255 only once you have decided to save the scene.
If ChPr is not closed, by indicating the last scene (Channel CHPR2 between 235-255), in AUTO mode all 16 scenes will be played
through even if not programmed.
MENU
REC
ENTER
DOWN
UP
ACTIVATE REC MODE
STEP 03
DRIVENET 1664
EMERGENCY
Menu
Up-Down
ENTER Up-Down
ENTER
EMERGENCY OPERATING MODE.
By setting this mode, it will be possible to
select one of the 16 pre-programmed
White cues that will then ran if DMX
signal is missing or not available.
Useful for emergency exit illumination on
public areas.
Dimmer level selectable by user.
14
MENU
EMERGENCY
ENTER
DOWN
UP
SELECTION
OFF
MENU
EMERGENCY
ENTER
DOWN
UP
WHITE
1
MENU
EMERGENCY
ENTER
DOWN
UP
DIMMER
255
EMERGENCY
Disable = Default
WHITE (1-16)
Default = WHITE 1
DIMMER
Default = 255
DEFAULT SET
Menu
Up-Down
ENTER Up-Down
ENTER
MENU
DEFAULT SET
ENTER
DOWN
UP
SURE?
MENU: NO - ENTER: YES
DEFAULT SETTINGS
To restore factory settings
TEMPERATURES
Menu
Up-Down
ENTER Up-Down
ENTER
MENU
TEMPERATURES
ENTER
DOWN
UP
Dsp: 42.5
B1:47.6 B2:46.8 B3:45.5 B4:42.6
TEMPERATURES
Display board and 4 LED Driver boards
temperature monitoring
MEASURES
Menu
Up-Down
ENTER Up-Down
ENTER
MENU
MEASURES
ENTER
DOWN
UP
Display
48.3 V
STATUS OF THE CONNECTED UNITS
This menu allows to check the status
(current and voltage) of the connected
units.
MENU
MEASURES
ENTER
DOWN
UP
OUT 01
36.5 V, 0.700 A
SLAVE
Menu
Up-Down
ENTER Up-Down
ENTER
MENU
SLAVE
ENTER
DOWN
UP
SURE
MENU: NO - ENTER: YES
SLAVE MODE
The unit is forced to DMX address 1
receiving signal from the unit set in Auto
mode.
DRIVENET 1664
TIME
Menu
Up-Down
ENTER Up-Down
ENTER
This menu shows the total UNIT life time
and the RGBW life time
15
MENU
TIME
ENTER
DOWN
UP
UNIT
121 Hr - 36 min
Art-NET ENABLED or DISABLED
Default = DISABLED
NETWORK
Menu
Up-Down
ENTER Up-Down
ENTER
MENU
NETWORK
ENTER
DOWN
UP
Art-Net
DISABLED
Art-NET COMMUNICATION PROTOCOL
This menu allows to enable/disable the
Art-NET communication protocol.
With Art-NET enabled the Art-NET signal
has the priority on the DMX signal.
Art-NET DMX UNIVERSE
This menu allows to set the DMX
universe.
NETWORK SETTINGS
This menu allows to choose the mode to
set the network parameters (IP address,
Subnet mask, Gateway, DNS):
USE DHCP = automatic setting of the
network parameters through a DHCP
server on the local area network.
FIXED = Fixed setting of the network
parameters.
CUSTOM = Manual setting of the network
parameters.
IP ADDRESS
This menu shows the IP address of the
DRIVENET.
You can set up all bytes of the IP address
only if NETWORK SETTINGS = CUSTOM.
SUBNET MASK
This menu shows the subnet mask.
You can set up all bytes of the subnet
mask only if NETWORK SETTINGS =
CUSTOM.
GATEWAY
This menu shows the gateway.
You can set up all bytes of the gateway
only if NETWORK SETTINGS = CUSTOM.
DNS
This menu shows the domain name
server.
You can set up all bytes of the DNS only
if NETWORK SETTINGS = CUSTOM.
MENU
NETWORK
ENTER
DOWN
UP
NETWORK SETTINGS
USE DHCP
MENU
NETWORK
ENTER
DOWN
UP
IP ADDRESS
192 . 168 . 55 . 152
NETWORK SETTINGS: USE DHCP, FIXED
or CUSTOM
Default = USE DHCP
IP ADDRESS
IP address displaying
MENU
NETWORK
ENTER
DOWN
UP
SUBNET MASK
255 . 255 . 255 . 0
MENU
NETWORK
ENTER
DOWN
UP
GATEWAY
192 . 168 . 55 . 1
MENU
NETWORK
ENTER
DOWN
UP
DNS
192 . 168 . 55 . 1
SUBNET MASK
Subnet mask displaying
GATEWAY
Gateway displaying
DNS
Domain name server displaying
MENU
NETWORK
ENTER
DOWN
UP
Art-Net DMX Universe
1
Art-NET DMX Universe
Range: 0 - 255
Default = 0
DRIVENET 1664
Menu
FAN MAX SPEED
This menu allows to select the internal
fans speed
Menu
SOFTWARE
Display board and LED Driver boards
software version
Up-Down
Up-Down
SYSTEM
SOFTWARE
ENTER
ENTER
Up-Down
Up-Down
MENU
SYSTEM
FAN MAX SPEED
100%
MENU
SOFTWARE
DISPLAY
0D210511 v1.19 Nov 28 2016
MENU
SOFTWARE
DRIVER #1
Id:0D2E1483 v.1.11
MENU
SOFTWARE
DRIVER #2
Id:0D2E1482 v.1.11
ENTER
ENTER
ENTER
ENTER
DOWN
DOWN
DOWN
DOWN
UP
UP
UP
UP
FAN MAX SPEED
50% - 100%
Default = 100%
Display board software version
LED Driver board 1 software version
LED Driver board 2 software version
ENTER
ENTER
16
MENU
SOFTWARE
DRIVER #3
Id:0D2E147F v.1.11
ENTER
DOWN
UP
MENU
SOFTWARE
DRIVER #4
Id:0D2E1481 v.1.11
ENTER
DOWN
UP
DRIVENET 1664
1 RED 1
2 GREEN 1
3 BLUE 1
4 WHITE 1
5 RED 2
6 GREEN 2
7 BLUE 2
8 WHITE 2
9 RED 3
10 GREEN 3
11 BLUE 3
12 WHITE 3
13 RED 4
14 GREEN 4
15 BLUE 4
16 WHITE 4
DMX PROTOCOL
FULL TYPE 8 BIT 64 ch mode (Default)
17 RED 5
18 GREEN 5
19 BLUE 5
20 WHITE 5
21 RED 6
22 GREEN 6
23 BLUE 6
24 WHITE 6
25 RED 7
26 GREEN 7
27 BLUE 7
28 WHITE 7
29 RED 8
30 GREEN 8
31 BLUE 8
32 WHITE 8
RED 1 Parameter:
DMX CHANNEL
Mid point
Move
DMX range
Mode Option Function
range
Value DMX value
(degrees)
000-255
Proportional colour
1
DMX CHANNEL
2
Parameter: GREEN
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
000-255 Proportional colour
DMX CHANNEL
3
Parameter: BLUE 1
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
000-255
Proportional colour
1
DMX CHANNEL
4
Parameter: WHITE 1
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
000-255
Proportional colour
17
33 RED 9
34 GREEN 9
35 BLUE 9
36 WHITE 9
37 RED 10
38 GREEN 10
39 BLUE 10
40 WHITE 10
41 RED 11
42 GREEN 11
43 BLUE 11
44 WHITE 11
45 RED 12
46 GREEN 12
47 BLUE 12
48 WHITE 12
49 RED 13
50 GREEN 13
51 BLUE 13
52 WHITE 13
53 RED 14
54 GREEN 14
55 BLUE 14
56 WHITE 14
57 RED 15
58 GREEN 15
59 BLUE 15
60 WHITE 15
61 RED 16
62 GREEN 16
63 BLUE 16
64 WHITE 16
DRIVENET 1664
RED 2 Parameter:
DMX CHANNEL
Mid point
Move
DMX range
Mode Option Function
range
Value DMX value
(degrees)
000-255
Proportional colour
5
DMX CHANNEL
6
Parameter: GREEN 2
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
000-255 Proportional colour
DMX CHANNEL
7
Parameter: BLUE 2
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
000-255
Proportional colour
DMX CHANNEL
8
Parameter: WHITE 2
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
000-255
Proportional colour
RED 3 Parameter:
DMX CHANNEL
Mid point
Move
DMX range
Mode Option Function
range
Value DMX value
(degrees)
000-255
Proportional colour
9
DMX CHANNEL
10
Parameter: GREEN 3
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
000-255 Proportional colour
DMX CHANNEL
11
Parameter: BLUE 3
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
000-255
Proportional colour
DMX CHANNEL
12
Parameter: WHITE 3
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
000-255
Proportional colour
18
DRIVENET 1664
RED 4 Parameter:
DMX CHANNEL
Mid point
Move
DMX range
Mode Option Function
range
Value DMX value
(degrees)
000-255
Proportional colour
13
DMX CHANNEL
14
Parameter: GREEN 4
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
000-255 Proportional colour
DMX CHANNEL
15
Parameter: BLUE 4
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
000-255
Proportional colour
DMX CHANNEL
16
Parameter: WHITE 4
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
000-255
Proportional colour
RED 5 Parameter:
DMX CHANNEL
Mid point
Move
DMX range
Mode Option Function
range
Value DMX value
(degrees)
000-255
Proportional colour
17
DMX CHANNEL
18
Parameter: GREEN
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
000-255 Proportional colour
DMX CHANNEL
19
Parameter: BLUE 5
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
000-255
Proportional colour
5
DMX CHANNEL
20
Parameter: WHITE 5
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
000-255
Proportional colour
19
DRIVENET 1664
RED 6 Parameter:
DMX CHANNEL
Mid point
Move
DMX range
Mode Option Function
range
Value DMX value
(degrees)
000-255
Proportional colour
21
DMX CHANNEL
22
Parameter: GREEN 6
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
000-255 Proportional colour
DMX CHANNEL
23
Parameter: BLUE 6
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
000-255
Proportional colour
DMX CHANNEL
24
Parameter: WHITE 6
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
000-255
Proportional colour
RED 7 Parameter:
DMX CHANNEL
Mid point
Move
DMX range
Mode Option Function
range
Value DMX value
(degrees)
000-255
Proportional colour
25
DMX CHANNEL
26
Parameter: GREEN 7
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
000-255 Proportional colour
DMX CHANNEL
27
Parameter: BLUE 7
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
000-255
Proportional colour
DMX CHANNEL
28
Parameter: WHITE 7
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
000-255
Proportional colour
20
DRIVENET 1664
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32

DTS DRIVENET 1664 Manuale utente

Tipo
Manuale utente

in altre lingue