DTS TITAN PLUS SOLO Manuale utente

GB

Made in Italy

TITAN PLUS SOLO

User’s Manual rel 2.1

D.T.S. Illuminazione srl - ITALY

http://www.dts-lighting.it

TITAN PLUS SOLO

Le informazioni contenute in questo documento sono state attentamente redatte e controllate. Tuttavia

non è assunta alcuna responsabilità per eventuali inesattezze. Tutti i diritti sono riservati e questo

documento non può essere copiato, fotocopiato, riprodotto per intero o in parte senza previo consenso

scritto della D.T.S .

DTS si riserva il diritto di apportare senza preavviso cambiamenti e modifiche estetiche , funzionali o di

design a ciascun proprio prodotto. D.T.S non assume alcuna responsabilità sull’uso o sull’applicazione dei

prodotti o dei circuiti descritti.

The information contained in this publication has been carefully prepared and checked. However, no

responsibility will be taken for any errors. All rights are reserved and this document cannot be copied,

photocopied or reproduced, in part or completely, without prior written consent from D.T.S.

D.T.S. reserves the right to make any aesthetic, functional or design modifications to any of its products

without prior notice. D.T.S. assumes no responsibility for the use or application of the products or circuits

described herein.

Les informations contenues dans le présent manuel ont été rédigées et contrôlées avec le plus grand

soin. Nous déclinons toutefois toute responsabilité en cas d'éventuelles inexactitudes. Tous droits

réservés. Ce document ne peut être copié, photocopié ou reproduit, dans sa totalité ou partiellement,

sans le consentement préalable de .

se réserve le droit d'apporter toutes modifications et améliorations esthétiques, fonctionnelles ou

de design, sans préavis, à chacun de ses produits. décline toute responsabilité sur l'utilisation ou

sur l'application des produits ou des circuits décrits.

D.T.S

D.T.S.

Las informaciones contenidas en este documento han sido cuidadosamenteredactadas y

controladas. Con todo, no se asume ninguna responsabilidad por eventuales inexactitudes.

Todos los derechos han sido reservados y este documento no puede ser copiado, fotocopiado

o reproducido, total o parcialmente, sin previa autorizaciónescrita de

se reserva el derecho a aportar sin previo aviso cambios y modificaciones de carácter

estético, funcional o de diseño a cada producto suyo. no se asume responsabilidad de

ningún tipo sobre la utilización o sobre la aplicació

n de los productos o de los circuitos descritos.

D.T.S.

2

DESCRIPTION

TITAN PLUS SOLO is a new range of compact self-contained LED projectors designed for fixed

and mobile installations either indoor or outdoor.

All models are made on aluminium offering high resistance to mechanical stress, and IP20 or

IP65 protection rating.

TITAN PLUS SOLO range features

XLR Male / Female cable

connectors

TITAN PLUS is also available without integrated power supply.

Three dedicated lenses sets (Spot, Medium flood, Wide flood) are available for each model,

offering different light beam projection angles with even coverage of lighted areas.

TITAN PLUS SOLO can be controlled via any DMX lighting console.

TITAN PLUS range comprises 3 models, which employ different sets of LEDs tailored for distinct

applications: TITAN PLUS SOLO FULL COLOUR, TITAN PLUS SOLO RGBA and TITAN PLUS

SOLO WHITE.

TITAN PLUS SOLO FULL COLOUR: 15 x 3W Full Colour LEDs; 16 million colours; 1600 Lux at

3 m (spot lenses); linear colour temperature 2800°K ÷ 6500°K; 16 selectable types of White.

The 15 Full Colour LEDs all generate the same colour at the same time, so that the illuminated

object is not only uniformly lit, but also projects no false shadows.

TITAN PLUS SOLO RGBA: 54 x 1W P4 LEDs (12 x Red, 15 x Green, 15 x Blue, 12 x Amber); 16

million colours; 4446 Lux at 3 m (spot lenses); linear colour temperature 2800°K ÷ 6500°K; 16

selectable types of White. The LEDs distribution pattern guarantees high mixing quality for

RGBA colours and a uniform projection on surfaces, no matter what colour is used.

TITAN PLUS SOLO WHITE: 54 x 1W P4 LEDs (42 x White, 12 x Amber); 5292 Lux at 3 m (spot

lenses); linear colour temperature 2800°K ÷ 6500°K; 16 selectable types of White.

TITAN PLUS SOLO WHITE is ideal in various applications where colour is not needed and white

light must have well defined features.

Full Colour LEDs Power supply on board

03.LDB030S.F10 TITAN PLUS SOLO IP20 FULLCOLOUR SPOT LENSES

03.LDB030S.F25 TITAN PLUS SOLO IP20 FULLCOLOUR MEDIUM FLOOD LENSES

03.LDB030S.F40 TITAN PLUS SOLO IP20 FULLCOLOUR WIDE FLOOD LENSES

03.LDB036C.F10 TITAN PLUS SOLO C IP65 FULLCOLOUR SPOT LENSES

03.LDB036C.F25 TITAN PLUS SOLO C IP65 FULLCOLOUR MEDIUM FLOOD LENSES

03.LDB036C.F40 TITAN PLUS SOLO C IP65 FULLCOLOUR WIDE FLOOD LENSES

Red/Green/Blue/Amber LEDs Power supply on board

03.LDB030S.T10 TITAN PLUS SOLO IP20 RGBA SPOT LENSES

03.LDB030S.T25 TITAN PLUS SOLO IP20 RGBA MEDIUM FLOOD LENSES

03.LDB030S.T40 TITAN PLUS SOLO IP20 RGBA WIDE FLOOD LENSES

03.LDB036C.T10 TITAN PLUS SOLO C IP65 RGBA SPOT LENSES

03.LDB036C.T25 TITAN PLUS SOLO C IP65 RGBA MEDIUM FLOOD LENSES

03.LDB036C.T40 TITAN PLUS SOLO C IP65 RGBA WIDE FLOOD LENSES

3 X White/Amber LEDs Power supply on board

03.LDB030S.W10 TITAN PLUS SOLO IP20 WHITE SPOT LENSES

03.LDB030S.W25 TITAN PLUS SOLO IP20 WHITE MEDIUM FLOOD LENSES

03.LDB030S.W40 TITAN PLUS SOLO IP20 WHITE WIDE FLOOD LENSES

03.LDB036C.W10 TITAN PLUS SOLO C IP65 WHITE SPOT LENSES

03.LDB036C.W25 TITAN PLUS SOLO C IP65 WHITE MEDIUM FLOOD LENSES

03.LDB036C.W40 TITAN PLUS SOLO C IP65 WHITE WIDE FLOOD LENSES

an integrated power supply and is therefore extremely easy

to set up and use.

2 integrated power supply with different protection rating are available: IP20 (Powercon + XLR

connectors) and IP65 (3 x 1.5 sq mm Main AC cable 1 meter length +

1 meter cable length).

TITAN PLUS SOLO

3

LED technology

TITAN PLUS SOLO FULL COLOUR: 15 x Full Colour LEDs; 1600 Lux / 3 m (spot lenses)

TITAN PLUS SOLO RGBA: 54 x 1W P4 LEDs (12 x Red, 15 x Green, 15 x Blue, 12 x Amber;

4446 Lux / 3 m (spot lenses)

TITAN PLUS SOLO WHITE: 54 x 1W P4 LEDs (42 x White, 12 x Amber) 5292 Lux / 3 m (spot

lenses)

Variable colour temperature: 2.800°K÷6.500°K

No infrared emission; no ultraviolet emission

LEDs average lifespan: 100.000 hours

Optical units

3 lenses sets available (Spot, Medium flood, Wide flood)

Control

Via any DMX lighting console

Protection

IP20 or IP65 protection level against the penetration of solids and liquids

Construction

TITAN PLUS SOLO is made on aluminium

Power supply

Internal power supply

Connection

M12 connection system between head and power supply (

)

Powercon + XLR connectors

XLR Male / Female cable connectors

ACCESSORIES

Lenses set Spot (TITAN PLUS SOLO FULL COLOUR) (Cod. 03.LK.035)

Lenses set Medium flood (TITAN PLUS SOLO FULL COLOUR) (Cod. 03.LK.036)

Lenses set Wide flood (TITAN PLUS SOLO FULL COLOUR) (Cod. 03.LK.037)

Lenses set Spot (TITAN PLUS SOLO RGBA / WHITE) (Cod. 03.LK.038)

Lenses set Medium flood (TITAN PLUS SOLO RGBA / WHITE) (Cod. 03.LK.039)

Lenses set Wide flood (TITAN PLUS SOLO RGBA / WHITE) (Cod. 03.LK.040)

4x2xAWG24 multipolar black outdoor cable (Cod. 0509C062)

M12 female (8 poles) cable connector (Cod. 0520P050)

M12 male (8 poles) cable connector (Cod. 0520P051)

MAIN ELECTRICAL CHARACTERISTICS:

Input Voltage Range : Vin 90 - 260 Vac

Frequency : 50 - 60 HZ

Power Consumption Range : 6 - 100 W

Power Factor ( Pf) : 0.95 electronic PFC controller

Efficiency : 90% typical

Output:

Power Output Range : 4 channels output 1,5 - 25W per channel

Output Current : 350 mA @ 100% per channel (500mA @ 100% per channel in BOOST Mode)

Output Voltage : Vout 48V

Control Input:

Control Signal : DMX 512

Dimming System :Constant Current PWM

Address Range : DMX 512 channels addressable by display

TITAN PLUS SOLO IP20 / TITAN

PLUS SOLO IP65

panel (TITAN PLUS SOLO IP20)

3 x 1.5 sq mm Main AC cable 1 meter length + 1 meter

cable length (TITAN PLUS SOLO IP65)

TITAN PLUS SOLO

4

IMPORTANT SAFETY INFORMATION

Fire prevention:

Never locate the fixture on any flammable surface.

Minimum distance from flammable materials: 10 cm

Replace any blown or damaged fuses only with those of identical value

Prevention from electric shock:

High voltage is present inside the unit.

Unplug the unit prior to performing any operation which involves touching the inside of the unit.

This equipment must be grounded, do not connect to non-grounded supplies.

Use only AC supplies 90-260V, 50-60Hz

TITAN PLUS SOLO IP20 should never be located in position exposed to rain or in areas of

extreme humidity.

A good air ventilation is essential for proper equipment work.

Safety:

The external surface of the unit may exeed 50°C; never handle the unit until at least 5 minutes

have elapsed since the unit was turned off.

Never install the unit in an enclosed area lacking sufficient air flow.

The ambient temperature should not exeed 40°C and should not be lower than -10°C

UNIT DIMENSIONS:

The use of a thermal magnetic circuit breaker is recommended for each TITAN PLUS SOLO unit.

Unit Dimensions

(LxWxH)

250 x 256 x 206 mm

Weight

6,3 Kg

Packing Dimensions

(LxWxH)

300 x 320 x 220 mm

Weight

7,5 Kg

TITAN PLUS SOLO

5

INPUT/OUTPUT CONNECTIONS

TITAN PLUS SOLO IP20

Mains 90-260 V AC

50-60 Hz input Powerconn

Female panel connector

DMX IN/OUT

XLR 5 pins Male / Female

Panel Connectors

Fuse 3,15 AT

DMX IN/OUT

XLR 3 pins Male / Female

Panel Connectors

Panel display

Pin1

2

3

4

5

6

7

M12 LED output

Female cable connector

Pin1

2

3

4

5

6

7

M12 LED input

Male cable connector

LEDS

CONNECTOR PINOUT

4-GREEN -

5-BLUE +

6-BLUE -

7-AMBER - (RGBA / WHITE)

8-AMBER + (RGBA / WHITE)

1-RED +

2-RED -

3-GREEN +

LEDS

CONNECTOR

4-GREEN - (FC / RGBA / WHITE)

5-BLUE + (FC / RGBA / WHITE)

6-BLUE - (FC / RGBA / WHITE)

7-

1-RED + (FC / RGBA / WHITE)

2-RED - (FC / RGBA / WHITE)

3-GREEN + (FC / RGBA / WHITE)

TITAN PLUS SOLO

6

INPUT/OUTPUT CONNECTIONS

TITAN PLUS SOLO IP65

Mains 90-260 V AC

50-60 Hz input

3 x 1.5mm Cable

DMX IN/OUT

XRL 5 pin Female

Cable Connectors

Display panel

Pin1

2

3

4

5

6

7

M12 LED output

Female cable connector

Pin1

2

3

4

5

6

7

M12 LED input

Male cable connector

LEDS

CONNECTOR PINOUT

4-GREEN -

5-BLUE +

6-BLUE -

7-AMBER - (RGBA / WHITE)

8-AMBER + (RGBA / WHITE)

1-RED +

2-RED -

3-GREEN +

LEDS

CONNECTOR

4-GREEN - (FC / RGBA / WHITE)

5-BLUE + (FC / RGBA / WHITE)

6-BLUE - (FC / RGBA / WHITE)

7-

1-RED + (FC / RGBA / WHITE)

2-RED - (FC / RGBA / WHITE)

3-GREEN + (FC / RGBA / WHITE)

Fuse 3,15 AT

DMX IN/OUT

XRL 5 pin Male

Cable Connectors

2

CONTROLLER

S T A N D A R D

D M X 5 1 2

Please note that the XLR connectors installed on the TITAN PLUS IP65 have

an IP20 protection rate.

Thus, for any application where an IP65 rate is needed, the XLR connectors

must be protected within an IP65-rated container.

TITAN PLUS SOLO

7

DMX SIGNAL CONNECTION:

TITAN PLUS SOLO IP20

The unit operates using a digital DMX 512 signal. Connection between the controller and the unit or

between units must be carried out using a two pair screened ø0.5 mm.

P.S:

If the display showing the DMX address flashes, then one of the following errors has occurred:

- DMX signal not present

- DMX reception problem

For Installations where long distance DMX cable connections are needed, we suggest to use a DMX

terminator.

The DMX terminator is a male XLR 3-5 pins connector with a 120 ohm resistor Between pin 2 and 3.

The DMX terminator must be plugged into the last unit (DMX out panel connector) of the DMX line.

Ensure that the conductors do not touch each other. Do not connect the cable ground to the DMX

connector chassis. The plug housing must be isolated. Connect the mixer signal to the DMX IN

projector plug and connect it to the next projector by connecting the DMX OUT plug on the first unit to

the DMX IN plug of the second one.

In this way, all the projectors are cascade connected.

1

2

3

5

4

OUT

120 ohm

PIN 3

PIN 2

PLACE A 120 OHM RESISTOR BETWEEN PIN 2

AND 3 OF A MALE XRL CONNECTOR AND PLUG IT

INTO THE DMX OUT PANEL CONNECTOR OF THE

LAST UNIT CONNECTED TO THE DMX LINE

5

3

4 2

1

1=GND

2=DATA-

3=DATA+

CONTROLLER

S TA N D A R D

D M X 5 1 2

TITAN PLUS SOLO

8

5

3

4 2

1

1=GND

2=DATA-

3=DATA+

CONTROLLER

S TA N D A R D

D M X 5 1 2

DMX SIGNAL CONNECTION:

TITAN PLUS SOLO IP65

The unit operates using a digital DMX 512 signal. Connection between the controller and the unit or

between units must be carried out using a two pair screened ø 0.5 mm.

P.S:

If the display showing the DMX address flashes, then one of the following errors has occurred:

- DMX signal not present

- DMX reception problem

For Installations where long distance DMX cable connections are needed, we suggest to use a DMX

terminator.

The DMX terminator is a male XLR 3-5 pins connector with a 120 ohm resistor Between pin 2 and 3.

The DMX terminator must be plugged into the last unit (DMX out panel connector) of the DMX line.

Ensure that the conductors do not touch each other. Do not connect the cable ground to the DMX

connector chassis. The plug housing must be isolated. Connect the mixer signal to the DMX IN

projector plug and connect it to the next projector by connecting the DMX OUT plug on the first unit to

the DMX IN plug of the second one.

In this way, all the projectors are cascade connected.

1

2

3

5

4

OUT

120 ohm

PIN 3

PIN 2

PLACE A 120 OHM RESISTOR BETWEEN PIN 2

AND 3 OF A MALE XRL CONNECTOR AND PLUG IT

INTO THE DMX OUT PANEL CONNECTOR OF THE

LAST UNIT CONNECTED TO THE DMX LINE

Please note that the XLR connectors installed on the TITAN PLUS IP65 have

an IP20 protection rate.

Thus, for any application where an IP65 rate is needed, the XLR connectors

must be protected within an IP65-rated container.

TITAN PLUS SOLO

9

DMX ADDRESS

Projector 1 A001

Projector 2 A010 If you want to select the next projector, just add “9”

Projector 3 A019

….. A….

projector 6 A046

Projector 1 A001

Projector 2 A011 If you want to select the next projector, just add “10”

Projector 3 A021

….. A….

projector 6 A051

Selelcting the DMX address

1) Press the UP-DOWN key until you reach the required DMX address. The numbers on the

display will start to flash (but the new DMX address hasn't yet been set).

2) Press ENTER to confirm your selection. The numbers on the display will stop flashing and the

projector is now controlled by the new DMX address.

TIPS: if you keep pushed the UP or DOWN keys, the channels are calculated more quickly and

you get a faster selection.

2) Press ENTER to confirm your selection. The numbers on the display will stop flashing and the

projector is now controlled by the new DMX address.

TITAN PLUS SOLO FULL COLOR can be used in seven different modes: 9 DMX channels mode

(default), 5 DMX channels mode (Shutter + Dimmer + RGB), WALL mode (6 DMX channels; for

use with DTS Wall mounted DMX controller 0514L007), M3CH mode (4 DMX channels; Dimmer +

RGB), RGB mode (3 channels), 1 DMX channel mode or CUSTOM DMX mode (not yet

implemented).

TITAN PLUS SOLO RGBA and TITAN PLUS SOLO WHITE can be used in seven different modes:

10 DMX channels mode (default), 6 DMX channels mode (Shutter + Dimmer + RGBA), WALL

mode (6 DMX channels; for use with DTS Wall mounted DMX controller 0514L007), M4CH mode (5

DMX channels; Dimmer + RGBA), RGBA mode (4 channels), 1 DMX channel mode or CUSTOM

DMX mode (not yet implemented).

If you want to use the TITAN PLUS SOLO FULL COLOR in “WALL” mode, select the “WALL”

mode from the MODE menu and set the following addresses on the mixer: (To be used only

with DTS Wall mounted DMX controller 0514L007)

Projector 1 A001

Projector 2 A009

Projector 3 A017

….. A….

projector 6 A041

If you want to use the TITAN PLUS SOLO FULL COLOR in 9 channels mode, select the 9 CH

mode from the MODE menu and set the following addresses on the mixer:

If you want to use the TITAN PLUS SOLO RGB and TITAN PLUS SOLO WHITE in 10 channels

mode, select the 10 CH mode from the MODE menu and set the following addresses on the

mixer:

TITAN PLUS SOLO

If you want to select the next projector, just add “8”

DTS Wall mounted DMX controller 0514L007 assign 8 DMX

channels per unit also if some channels are not used

10

DISPLAY FUNCTIONS

TITAN PLUS SOLO

FULL COLOUR

DISPLAY FUNCTIONS

The TITAN PLUS SOLO FULL COLOUR display panel shows all the available functions . Using these

functions, it is possible to change some of the parameters and add some functions. Changing the

D.T.S. setting can vary the functions of the unit so that it does not respond to the DMX 512 signal

used to control it. Carefully follow the instructions below before carrying out any variations or

selections.

NOTE: the symbol shows which key has to be pushed to obtain the desired function.

Software version 4.07

TITAN PLUS SOLO

DOWN

UP

ENTER

MENU

Up-DownMENU ENTER

DMX MODE

To select DMX mode : 9 DMX channels

mode (default), 5 DMX channels mode

(Shutter + Dimmer + RGB), WALL mode

(6 DMX channels; for use with DTS Wall

mounted DMX controller 0514L007),

M3CH mode (4 DMX channels; Dimmer

+ RGB), RGB mode (3 channels), 1 DMX

channel mode.

5 CHANNELS

Up-Down

ENTER

Up-Down

MENU

ENTERUp-Down

REVERSE DISPLAY

Reverses display's reading depending on

the mounting position (on the ground or

suspended).

Up-Down

Floor

position

Suspension

position

Up-DownENTER

DISPLAY STAND BY

To turn off the display (after 5 seconds)

or leave it always on.

Display OFF

Display

always ON

ENTER

Default DMX Mode = 9 CH

9 CHANNELS

Up-Down

ENTER

AUX MODE

Up-Down

Up-DownENTER

ENTER

Custom mode enabled

Show Custom settings

Parameters Setting on

Custom Mode

CUSTOM DMX mode let you set the

parameters for Shutter, Dimmer, Red,

Green, Blue, Ctc, Macro and Function to

the desired DMX channels.

(not yet implemented)

AUX mode let you activate an external

ON -OFF control on IR connector.

(not implemented on TITAN PLUS)

1 CHANNEL

Up-Down

ENTER

RGB (3 CHANNELS)

Up-Down

ENTER

External ON - OFF control on IR

connector (not implemented on

TITAN PLUS)

Up-Down

ENTER

Up-Down

Up-DownENTER

ENTER

6 CHANNELS

M3CH (4 CHANNELS)

Up-Down

ENTER

Shutter + Dimmer + RGB

Dimmer + RGB

Standard mode enabled:

(Default).

Extended mode enabled:

Rainbow effects on MACRO

channel.

MACRO

MACRO Function enables channel

mapping macro rainbow effects

STD (default)

11

TITAN PLUS SOLO

12

Up-Down

MENU

ENTERUp-Down

LED

RGB Min/Max, Smooth, Compression,

Sync and Boost level values settings

Up-Down

Up-DownENTER

ENTER

Up-Down

Up-DownENTER

ENTER

RGB MINIMUM VALUES

This menu allow to select the

minimum levels for Red,Green and

Blue

RGB MAXIMUM VALUES

This menu allow to select the

maximum levels for Red,Green and

blue

Default = 100

Default = 0

Default = 100

These settings have priority

on Master Dimmer channel

Up-Down

Up-DownENTER

ENTER

Range = Off-20

Default = 4

SMOOTH VALUE

This menu allow to select the value

of the delay (in milliseconds) for

RGB and Dimmer channels

reaction to DMX or Program

variation.

Off=25 ms delay (Fast response)

20=250 ms delay (Slow response)

Off = 25 ms

Istant responce to DMX variation

20 = 250 ms

Smooth response to DMX variation

Up-Down

Up-DownENTER

ENTER

Linear = Linear

current output

COMPRESSION

This menu allow to select between

linear current output or quadratic

current output for LEDs

Default = Linear

Quadratic =

Linear light

output

ENTER

SYNC

This menu allow to adjust the PWM

frequency value (Hz) in order to

reduce flickering in the process of

your camera recordings

Up-Down

Up-DownENTER

Range = 610 Hz -10 KHz

Default = 610 Hz

ENTER

Boost mode activated

With BOOST active, the LED’s

current is set to 500 mA

(30%more gain).

Default = Activated

Up-DownENTER

ENTER

BOOST DRIVING

This menu allow to increase the LED’s

current from 350 mA to 500 mA

Boost mode deactivated

Up-Down

ENTER

TITAN PLUS SOLO

Up-DownENTER ENTER

WHITE MACROS

16 macros for White colour from

2800 to 6500 ° K

Up-DownENTER

ENTER

DIMMER

Dimmer level selectable by user

as on DMX channel 2 (Dimmer)

Dimmer level is active for all the

programs and macros

SHUTTER

Shutter level selectable by user

as on DMX channel 1 (Shutter)

Shutter level is active only for

CU01/CU16 and Wh01/Wh16

macros

ESC

Exit from Automatic Mode Menu

ENTER

MENU

Up-Down

Up-DownENTER ENTER

Up-Down

ENTER

AUTOMATIC MODE

Automatic demo game without

DMX controller

ChPr

Chase with 16 steps previously

created in REC MODE

Speed and Wait time selectable

by user

ENTER

Up-Down

CUPr

RGB values selectable by user

Rainbow (rAIn)

Rainbow colours effect.

Speed time selectable by user

ENTER

Up-Down

CU01-CU16

Color Macros as on DMX channel

8 (Macro)

Up-DownENTER ENTER

13

TITAN PLUS SOLO

Up-DownENTER

ENTER

MENU

Up-Down

ENTER

SLAVE MODE

Slave mode for ChPr program.

All slave units will be

synchronised with master unit,

running their own Chpr program.

Up-DownENTER

MENU

Up-Down

ENTER

INFRARED MODE

Infrared remote control.

By activating Ir MODE, it will be

possible to navigate trought the

unit functions by using the D.T.S.

infrared remote control.

D.T.S. Code: 0514L008

NOTE:

External infrared remote sensor

needed.

D.T.S. Code :03.LA.016

NOT IMPLEMENTED ON TITAN

PLUS

EMERGENCY

Emergency operating mode.

By setting Emergency mode, it

will be possible to select one of

the 16 preprogrammed WHITE

cues that will then ran if DMX

signal is missing or not available.

Usefull for Emergency EXIT

illumination on public areas.

Up-Down

MENU

Up-DownENTER

ENTER

Default = OFF

Default = White 1

Default = 255

ENTER

DMX Recorder Mode

For the programming of ChPr by using a DMX controller, besides the 9 channels necessary to control the unit a further 3 DMX channels are

needed.

So that in RECORDER mode ( via DMX) the unit will need 12 channels to be correctly programmed.

The three new DMX channels are:

DMX channel 10 = SCENES channel

From 0-10 = no function ( r001)

From 11-255 are displayed the programmable scenes (max 16 scenes from M001 to M0016 )

DMX channel 11 = EDIT channel:

-From 0-19 = no function

-From 20-234 the unit runs the configuration given by the received input DMX values.

With the channel SCENES it is possible to pass from one step to the next while with REC it is possible to record the selected scene.

-From 235-255 the unit runs the configuration given by the received input DMX values closing the sequence as last scene.

With the channel REC it is possible to record the selected scene as last scene.

DMX channel 12 = RECORDING channel

Records the set scene with a variation between 0 to 255 (the display flashes indicating that the scene has been recorded). It is advised that you

keep the REC channel set to 0 and to run through the 255 only once you have decided to save the scene. If ChPr is not closed, by indicating the

last scene (Edit channel between 235-255), in playback mode all 16 scenes will be played through even if not programmed.

Up-DownENTER

MENU

Up-Down

ENTER

FAN SPEED CONTROL

Internal Fan Speed control

selectable by user.

Range: OFF - 24 volt

Default : 24 Volt

Fan Speed Control

Range: OFF - 24 volt

Default = 24 Volt

14

ENTER

MENU

Up-Down

REC MODE

In DMX Recorder Mode, it is possible to

create and store the scenes of the ChPr

by using an external DMX controller.

The unit must be setted to 10 channels

MODE

ENTER

Up-DownENTER

LIFE TIME

This menu show the total UNIT life time

and the RGBA life time

Up-Down

MENU

ENTER

Up-Down

MENU

SOFTWARE

Software version

ENTER

TEST MODE

RGB colours test with rainbow

Up-Down

MENU

.

TITAN PLUS SOLO

15

DEFAULT

To restore default settings

TEMPERATURE

Internal Unit temperature

visualisation

MENU

Up-Down

ENTER

.

ENTER

Internal Unit temperature.

(° Celsius)

.

DISPLAY FUNCTIONS

TITAN PLUS SOLO RGBA

TITAN PLUS SOLO WHITE

DISPLAY FUNCTIONS

The TITAN PLUS SOLO RGBA/WHITE display panel shows all the available functions . Using these

functions, it is possible to change some of the parameters and add some functions. Changing the

D.T.S. setting can vary the functions of the unit so that it does not respond to the DMX 512 signal

used to control it. Carefully follow the instructions below before carrying out any variations or

selections.

NOTE: the symbol shows which key has to be pushed to obtain the desired function.

Software version 4.07

TITAN PLUS SOLO

16

Up-Down

MENU

ENTERUp-Down

REVERSE DISPLAY

Reverses display's reading depending on

the mounting position (on the ground or

suspended).

Up-Down

Floor

position

Suspension

position

Up-DownENTER

DISPLAY STAND BY

To turn off the display (after 5 seconds)

or leave it always on.

Display OFF

Display

always ON

ENTER

Up-DownMENU ENTER

6 CHANNELS

Up-Down

ENTER

Default DMX Mode = 10 CH

10 CHANNELS

1 CHANNEL

Up-Down

ENTER

RGBA (4 CHANNELS)

Up-Down

ENTER

6 CHANNELS

Up-Down

ENTER

DMX MODE

To select DMX mode : 10 DMX channels

mode (default), 6 DMX channels mode

(Shutter + Dimmer + RGBA), WALL

mode (6 DMX channels; for use with

DTS Wall mounted DMX controller

0514L007), M4CH mode (5 DMX

channels; Dimmer + RGBA), RGBA mode

(4 channels), 1 DMX channel mode.

CUSTOM DMX mode let you set the

parameters for Shutter, Dimmer, Red,

Green, Blue, Amber, Ctc, Macro and

Function to the desired DMX channels.

(not yet implemented)

AUX mode let you activate an external

ON -OFF control on IR connector.

(not implemented on TITAN SOLO)

ENTER

Up-Down

Up-DownENTER

ENTER

Standard mode enabled:

(Default).

Extended mode enabled:

Rainbow effects on MACRO

channel.

MACRO

MACRO Function, enable channel

mapping macro rainbow effects

STD (default)

Up-Down

ENTER

AUX MODE

Up-Down

Up-DownENTER

ENTER

Custom mode enabled

Show Custom settings

Parameters Setting on

Custom Mode

External ON - OFF control on IR

connector (not implemented on

TITAN SOLO)

M4CH (5 CHANNELS)

Up-Down

ENTER

Dimmer + RGBA

DOWN

UP

ENTER

MENU

TITAN PLUS SOLO

Up-Down

MENU

ENTERUp-Down

LED

RGBA Min/Max, Smooth, Compression,

Sync and Boost level values settings

Up-Down

Up-DownENTER

ENTER

Up-Down

Up-DownENTER

ENTER

RGBA MINIMUM VALUES

This menu allow to select the

minimum levels for Red, Green,

Blue and Amber

RGBA MAXIMUM VALUES

This menu allow to select the

maximum levels for Red, Green,

Blue and Amber

Default = 100

Default = 0

Default = 100

These settings have priority on

Master Dimmer

Up-Down

Up-DownENTER

ENTER

Range = Off - 20

Default = 4

SMOOTH VALUE

This menu allow to select the value

of the delay (in milliseconds) for

RGBA and Dimmer channels

reaction to DMX or Program

variation.

Off = 25 ms delay (Fast response)

20 = 250 ms delay (Slow response)

Off = 25 ms

Istant responce to DMX variation

20 = 250 ms

Smooth response to DMX variation

Up-Down

Up-DownENTER

ENTER

Linear = Linear

current output

COMPRESSION

This menu allow to select between

Linear current output or quadratic

current output for LEDs

Default = Linear

Quadratic =

Linear light

output

ENTER

Up-DownENTER

ENTER

Default = 0

Default = 100

SYNC

This menu allow to adjust the PWM

frequency value (Hz) in order to

reduce flickering in the process of

your camera recordings

Up-Down

Up-DownENTER

Range =

610 Hz -10 KHz

Default = 610 Hz

ENTER

Boost mode activated

Whit BOOST active,the LED’s

current is set to 500 mA

(30%more gain).

Default = Activated

Up-DownENTER

ENTER

BOOST DRIVING

This menu allow to increase the LED’s

current from 350 mA to 500 mA

Boost mode deactivated

Up-Down

ENTER

17

TITAN PLUS SOLO

Up-DownENTER ENTER

WHITE MACROS

16 macros for White color from

2800 to 6500 ° K

Up-DownENTER

ENTER

DIMMER

Dimmer level selectable by user

as on DMX channel 2 (Dimmer)

Dimmer level is active for all the

programs and macros

SHUTTER

Shutter level selectable by user

as on DMX channel 1 (Shutter)

Shutter level is active only for

CU01/CU16 and Wh01/Wh16

macros

ESC

Exit from Automatic Mode Menu

ENTER

MENU

Up-Down

Up-DownENTER ENTER

Up-Down

ENTER

AUTOMATIC MODE

Automatic demo game without

DMX controller

ChPr

Chase with 16 steps previously

created in REC MODE

Speed and Wait time selectable

by user

ENTER

Up-Down

CUPr

RGBA values selectable by user

Rainbow (rAIn)

Rainbow colours effect.

Speed time selectable by user

ENTER

Up-Down

CU01-CU16

Color Macros as on DMX channel

8 (Macro)

Up-DownENTER ENTER

18

TITAN PLUS SOLO

Up-DownENTER

ENTER

MENU

Up-Down

ENTER

SLAVE MODE

Slave mode for ChPr program.

All slave units will be

synchronised with master unit,

running their own Chpr program.

Up-DownENTER

MENU

Up-Down

ENTER

INFRARED MODE

Infrared remote control.

By activating Ir MODE, it will be

possible to navigate trought the

unit functions by using the D.T.S.

infrared remote control.

D.T.S. Code :0514L008

NOTE:

External infrared remote sensor

needed.

D.T.S. Code :03.LA.016

Not Implemented on TITAN PLUS

ENTER

MENU

Up-Down

ENTER

REC MODE

In DMX Recorder Mode,it is

possible to create and store the

scenes of the ChPr by using an

external DMX controller.

The unit must be setted to 10

channels MODE

DMX Recorder Mode

For the programming of ChPr by using a DMX controller, besides the 10 channels necessary to control the unit a further 3 DMX

channels are needed.

So that in RECORDER mode ( via DMX) the unit will need 13 channels to be correctly programmed.

The three new DMX channels are:

DMX channel 11 = SCENES channel

From 0-10 = no function ( r001)

From 11-255 are displayed the programmable scenes (max 16 scenes from M001 to M0016 )

DMX channel 12 = EDIT channel:

-From 0-19 = no function

-From 20-234 the unit runs the configuration given by the received input DMX values.

With the channel SCENES it is possible to pass from one step to the next while with REC it is possible to record the selected scene.

-From 235-255 the unit runs the configuration given by the received input DMX values closing the sequence as last scene.

With the channel REC it is possible to record the selected scene as last scene.

DMX channel 13 = RECORDING channel

Records the set scene with a variation between 0 to 255 (the display flashes indicating that the scene has been recorded).It is

advised that you keep the REC channel set to 0 and to run through the 255 only once you have decided to save the scene. If ChPr is

not closed, by indicating the last scene ( Edit channel between 235-255), in playback mode all 16 scenes will be played through even

if not programmed

Up-DownENTER

MENU

Up-Down

ENTER

FAN SPEED CONTROL

Internal Fan Speed control

selectable by user.

Range: OFF - 24 volt

Default : 24 Volt

Fan Speed Control

Range: OFF - 24 volt

Default = 24 Volt

EMERGENCY

Emergency operating mode.

By setting Emergency mode, it

will be possible to select one of

the 16 preprogrammed WHITE

cues that will then ran if DMX

signal is missing or not available.

Usefull for Emergency EXIT

ilumination on public areas.

Up-Down

MENU

Up-DownENTER

ENTER

Default = OFF

Default = White 1

Default = 255

ENTER

19

TITAN PLUS SOLO

SERVICE MENU

For technical personnel only

To operate this menu:

-Connect the unit to the main

-While reset is running, press the MENU and ENTER keys at the same time.

EXIT

Exit from hidden menu.

CHANNELS

This menu allow to set 3 channels or 4 channels LEDs output mode

3 LEDs channels output mode = TITAN PLUS SOLO FULL COLOUR

4 LEDs channels output mode = TITAN PLUS SOLO RGBA / TITAN PLUS SOLO WHITE

ENTERENTER

DEFAULT

To restore default settings

Up-Down

MENU

ENTERENTER

TEMPERATURE

Internal Unit temperature

visualisation

Up-Down

MENU

.

Internal Unit temperature.

(° Celsius)

ENTER

Up-DownENTER

LIFE TIME

This menu show the total UNIT life time

and the RGBA life time

Up-Down

MENU

ENTER

Up-Down

MENU

SOFTWARE

Software version

ENTER

TEST MODE

RGB colours test with rainbow

Up-Down

MENU

.

20

.

PRODUCT MODEL SELECTION:

TITAN PLUS = Default

FOS 100 POWER = only for FOS 100 POWER unit

DELTA 8 = only for DELTA 8 unit

La pagina sta caricando ...

DTS TITAN PLUS SOLO Manuale utente

DTS TITAN PLUS SOLO Manuale utente

in altre lingue

Documenti correlati

Altri documenti