Vermeiren Sigma 230 Manuale utente

VERMEIREN

Sigma

Sigma 230

I N S T R U C T I O N M A N U A L

M A N U E L D ' U T I L I S A T I O N

G E B R U I K S A A N W I J Z I N G

G E B R A U C H S A N W E I S U N G

M A N U A L E D I I S T R U Z I O N I

M A N U A L D E I N S T R U C C I O N E S

I N S T R U K C J A O B S Ł U G I

N Á V O D K O B S L U Z E

Instrukcje dla wyspecjalizowanego

No part of this manual may be reproduced in any form what so

ever (print, photocopy, microfilm or any other process) without

written permission of the publisher, or processed, duplicated or

distributed by using electronic systems.

Aucune partie de ce manuel ne peut être reproduite, sous

quelque forme que ce soit (imprimée, photocopie, microfilm ou

tout autre procédé) sans l'autorisation écrite du publicateur, ni

traitée, dupliquée ou distribuée à l'aide de systèmes

électroniques.

Alle rechten, inclusief vertaling, voorbehouden.

Niets uit deze handleiding mag geheel of gedeeltelijk in enige

vorm (druk, fotokopie, microfilm of ieder ander procedé) zonder

de schriftelijke toelating van de uitgever worden

gereproduceerd of met behulp van elektronische systemen

worden verwerkt, gekopieerd of verspreid.

Alle Rechte, auch an der Übersetzung, vorbehalten.

Kein Teil der Gebrauchsanweisung darf in irgendeiner Form

(Druck, Fotokopie, Mikrofilm oder einem anderen Verfahren)

ohne schriftliche Genehmigung des Herausgebers

reproduziert oder unter Verwendung elektronischer Systeme

verarbeitet, vervielfältigt oder verbreitet werden.

Il presente manuale non può essere riprodotto, neppure

parzialmente, con alcun mezzo (stampa, fotocopia, microfilm o

altro procedimento) senza l’autorizzazione scritta della casa

produttrice, né elaborato, duplicato o distribuito con l’ausilio di

sistemi elettronici.

traducción.

Se prohíbe la reproducción total o parcial del presente manual

de cualquier forma (impresión, fotocopia, microfilm o cualquier

otro procedimiento), así como la edición, copia o distribución

empleando sistemas electrónicos, sin el permiso escrito del

editor.

Wszelkie prawa zastrzeżone, łącznie z tłumaczeniem.

Żadna część niniejszej instrukcji nie może być powielana w

jakiejkolwiek formie (drukowanej, fotokopii, mikrofilmu ani

innej) bez pisemnej zgody wydawcy, nie może być również

przetwarzana, kopiowana ani rozprowadzana za pomocą

systemów elektronicznych.

Všechna práva vyhrazena, včetně překladu.

Šíření jakékoliv části tohoto katalogu jakýmkoliv způsobem

(tisk, kopie, mikrofilm nebo jiný způsob) bez písemného

souhlasu vydavatele, nebo zpracování, duplikace či distribuce

prostřednictvím elektronických systémů je zakázáno.

EN

Instructions for specialist dealer

This instruction manual is part and parcel of the

product and must accompany every product

sold.

Version: F, 2021-01

FR

Instructions pour les distributeurs

Ce manuel d'instructions fait partie du produit et

doit accompagner chaque produit vendu.

Version : F, 2021-01

NL

Instructies voor de vakhandelaar

Deze handleiding is deel van het product en

dient bij iedere product te worden geleverd.

Versie: F, 2021-01

DE

Hinweise für den Fachhändler

Diese Gebrauchsanweisung ist Bestand-teil des

Produkts und ist bei jeder Produkts

auszuhändigen.

Version: F, 2021-01

IT

Istruzioni per il rivenditore

Il presente Manuale di istruzioni è parte

integrante del prodotto e deve essere fornito

assieme alla prodotto.

Versione: G, 2021-01

ES

Instrucciones destinadas a los distribuidores

especializados

El presente manual de instrucciones es parte

integrante del producto y se debe adjuntar a

todas las producto que se vendan.

Versión: F, 2021-01

PL

sprzedawcy

Niniejsza instrukcja obsługi jest nieodłączną

częścią produktu i musi być dołączona do

każdego sprzedawanego produktu.

Wersja: F, 2021-01

CS

Pokyny pro specializovaného prodejce

Tento návod k obsluze je součástí dodávky a

musí být součástí každého prodaného

produktu.

Verze: F, 2021-01

Basic UDI: 5415174 122127Sigma 6B

5415174 122127Sigma 230 5X

Multi version: G, 2021-01

Language index

English

Français

Nederlands

Deutch

Italiano

Español

Polski

Czech

User manual

Manuel d'utilisation

Gebruiksaanwijzing

Bedienungshandbuch

Manuale di istruzioni

Manual de instrucciones

Instrukcja obsługi

Návod k obsluze

This page is intentionally left blank

Sigma, Sigma 230

2021-01

Content

1

EN

NL

Content

Preface........................................................................................................................ 2

1 Your product .................................................................................................. 3

1.1 Description ...................................................................................................... 3

1.2 Options ........................................................................................................... 5

2 Before use ..................................................................................................... 6

2.1 Intended use ................................................................................................... 6

2.2 General safety instructions ............................................................................. 6

2.3 Symbols on the wheelchair ............................................................................. 7

2.4 Transport ......................................................................................................... 7

2.5 First use and storage .................................................................................... 10

3 Using your wheelchair ................................................................................ 11

3.1 First ride ........................................................................................................ 11

3.2 Driving outdoors ............................................................................................ 11

3.3 Operating console ......................................................................................... 13

3.4 Brake and free-wheel lever ........................................................................... 13

3.5 Battery switch................................................................................................ 14

3.6 Moving to/from wheelchair ............................................................................ 14

3.7 Comfort adjustments ..................................................................................... 15

3.8 Battery status and charging .......................................................................... 18

4 Maintenance ................................................................................................ 19

4.1 Time of maintenance..................................................................................... 19

4.2 Instructions for maintenance ......................................................................... 20

4.3 Troubleshooting ............................................................................................ 20

4.4 Reuse ........................................................................................................... 21

4.5 End of use ..................................................................................................... 21

5 Technical specifications ............................................................................. 22

Sigma, Sigma 230

2021-01

Preface

2

EN

NL

Preface

Congratulations! You are now owner of a Vermeiren wheelchair!

This wheelchair is made by qualified and committed personnel. It is designed and produced

according to high quality standards, guarded by Vermeiren.

Thank you for your trust in the products of Vermeiren. To support you on the use of this wheelchair

and its operating options, this manual is offered. Please read it carefully; it will help you to get

familiar with the operation, capabilities and limitations of your wheelchair.

If you still have questions after reading this manual, do not hesitate to contact your specialist

dealer. He/she will be glad to help you.

Important note

To ensure your safety and to prolong the lifetime of your product, please take good care of it and

have it checked and serviced on a regular basis.

This manual reflects the latest product developments. Vermeiren has the right to implement

changes to this type of product without any obligation to adapt or replace similar products

previously delivered.

Pictures of the product are used to clarify the instructions in this manual. Details of the depicted

product may deviate from your product.

Information available

On our website http://www.vermeiren.com/ you will always find the most recent version of the

information in this manual. Please consult this website regularly for possible updates.

Visually impaired people can download the electronic version of this manual and have it read out

by means of a text-to-speech software application.

This user manual

For user and specialist dealer

User manual of applied operating console and battery charger.

For user and specialist dealer

Installation instructions (Instructions for detail adjustments and (dis)assembly)

For specialist dealer

Service manual for wheelchairs

For specialist dealer

EC declaration of conformity

Sigma, Sigma 230

2021-01

Your product

3

EN

NL

1 Your product

1.1 Description

This Sigma, Sigma 230 wheelchair is easy to operate and can be used indoors as well as

outdoors. The wheelchair has a mid-wheel drive which makes stable driving possible. Depending

on the type of wheelchair and installed options, electrical adjustment of backrest, seat and leg

rest is possible.

The following pictures shows all parts that are relevant to the user. In the operation and

maintenance section, these parts are described if applicable.

Important parts

Before using your wheelchair, check the technical details and limits of intended use. See

chapter 5.

To adjust your wheelchair, see the comfort adjustments in § 3.7 and/or the adjustments in

the installation manual. Also consult our website http://www.vermeiren.com/

1. Backrest

2. Arm pad (2x)

3. Seat

4. Footrest B06 (2x)

5. Footplate B06 (2x)

6. Battery housing

7. Front wheel (2x)

8. Mid wheel/drive wheel

(2x)

9. Rear wheel (2x)

10. Armrest (2x)

1

3

4

6

9

2

8

10

7

5

Sigma, Sigma 230

2021-01

Your product

4

EN

NL

Important parts, continued

11. Front light (2x)

12. Mudguard (2x)

13. Motor with free-

wheel lever (2x)

14. Balance arm

15. Rear light (2x)

16. Battery switch

17. Motor backrest tilt

18. Push bar

19. Operating console

20. Connection point

battery charger

21. Console support

22. Identification plate

23. Calf rest BZ10E (2x)

24. Footplate BZ10E (1x)

25. Footrest BZ10E (1x)

23

24

25

19

11

17

18

14

12

13

21

20

16

15

22

Sigma, Sigma 230

2021-01

Your product

5

EN

NL

1.2 Options

Type

Description

SE30

Manual seat adjustment

SE34

Manual backrest adjustment

SE36

Manual backrest adjustment; max. inclination angle 30° with

gas springs

SE39

Electrical seat; max. inclination angle 20°

Electrical backrest; max. inclination angle 30°

(2 actuators)

SE40

Electrical seat; max. inclination angle 20°; one actuator

SE41

Electrical backrest; max. inclination angle 30°; one actuator

SE42+SE40

Vertical lift, max.300 mm

Electrical seat; max. inclination angle 45°

(2 actuators)

SE42+SE39

Vertical lift, max.300 mm

Electrical seat; max. inclination angle 50°

Electrical backrest; max. inclination angle 30°

(3 actuators)

SE43

Electrical seat; max. inclination angle 50°

Electrical backrest; max. inclination angle 30°

(2 actuators)

Sigma, Sigma 230

2021-01

Before use

6

EN

NL

2 Before use

2.1 Intended use

In this paragraph a brief description of the intended use of your wheelchair is given. Additionally,

relevant warnings are added to the instructions in the other paragraphs. In this way we would like

to make you aware of the possible misuse that may appear.

• Indications and contraindications: This wheelchair is meant to be operated by the user sitting

in the wheelchair. The wheelchair is designed and produced to be a transport aid for users who

suffer from paralysis, loss of limbs or limb deformations/defects, heart insufficiencies, … You

should NOT use this wheelchair if you suffer from physical or mental impairments that may put

you, or other people, in danger when driving the wheelchair. For this reason, consult your

doctor first and make sure that your specialist dealer is informed about his advice.

• This wheelchair is suitable for indoor and outdoor use.

• This wheelchair is designed and produced solely to transport/transfer one (1) person with a

maximum weight of 140kg. It is not designed for transportation of goods or objects, nor for any

use other than previously described.

• Only use accessories and spare parts approved by Vermeiren.

• Please read all technical details and limits of your wheelchair in chapter 5.

• The warranty on this product is based on normal use and maintenance as described in this

manual. Damage to your product caused by improper use or lack of maintenance will cause

the warranty to lapse.

2.2 General safety instructions

Risk of injuries and/or damage

Please read and follow the instructions in this manual. Otherwise you may get injured or your

wheelchair may get damaged.

Keep the following general warnings in mind during use:

• Do not use your wheelchair if you are under influence of alcohol, medicines or other substances

that may influence your driving abilities.

• Be aware that some parts of your wheelchair may get very hot or cold due to ambient

temperature, solar radiation, heating devices or due to the motor drive during the ride. Be

careful when touching. Wear protective clothing if the weather is cold. After a ride, wait until

the wheelchair/motor has cooled down.

• Before switching the wheelchair on, be aware of the environment/situation in which you are

located. Adjust your speed to this before driving off. We advise you to use the slowest speed

setting to drive indoors. For outdoor driving you can adjust the speed to a suitable speed at

which you feel comfortable and safe.

• ALWAYS keep in mind that your wheelchair may stop suddenly due to a discharged battery or

a protection that prevents your wheelchair from further damage. Also check the possible

causes mentioned in § 4.3. Use your safety belt to prevent injuries.

• Your wheelchair has been tested for electromagnetic compatibility and complies with the

standard, see chapter 6. Nevertheless, sources of electromagnetic fields may influence the

driving performance of your wheelchair, such as the fields of mobile phones, power generators

or high-power energy sources. On the other hand, the electronics of your wheelchair can affect

other electronic appliances too, such as alarm systems of shops and automatic doors. We

therefore advise you to check your wheelchair regularly for damage and wear, since these may

enlarge the interference (see also chapter 4).

CAUTION

Sigma, Sigma 230

2021-01

Before use

7

EN

NL

• Only drive on flat surfaces where both driving wheels touch the ground and where there is

sufficient contact to operate the wheelchair safely.

• Alterations or substitutions should not be made to the wheelchair securement points or to

structural and frame parts or components without consulting the wheelchair manufacturer.

• Make sure that your hands, clothes, belts, buckles or jewellery don’t get caught by wheels or

other moving parts during use.

2.3 Symbols on the wheelchair

The symbols in following list are applicable to your wheelchair. Symbols can be found in the

relevant ISO standard (ISO 7000, ISO 7001 and IEC 417).

Maximum weight of the user in kg

Indoor/outdoor use (battery charger excluded)

Indoor use only (battery charger)

Maximum safe slope in ° (degrees).

Maximum speed

Type designation

Risk of entrapment

2.4 Transport

Risk of damage

Take action to protect the wheelchair from being damaged during transport.

The wheelchair cannot be disassembled without tools and is relatively heavy to carry.

2.4.1 Moving out of the way

Use the operating console to drive the wheelchair to its destination.

Otherwise, put the wheelchair in free-wheel mode (see §3.4) and use the push bar to move it.

2.4.2 Transport by aircraft

Since the wheelchair is equipped with non-spillable AGM batteries, it is possible to transport the

wheelchair (as a whole) by aircraft. Consult your airline for the correct handling procedures before

booking your flight. Before handing your wheelchair over to the airport personnel, disconnect the

battery from the wheelchair, see § 3.5.

CAUTION

Sigma, Sigma 230

2021-01

Before use

8

EN

NL

2.4.3 Transport by vehicle, as luggage

Risk of injuries and damage

• Make sure that the free-wheel lever is in braking position during transport, see § 3.4.

• Do not drive the wheelchair into the vehicle while the user is still seated in it.

To drive the wheelchair into the vehicle:

1. Use the operating console to return your wheelchair to stable position, see § 3.3.

2. Remove all mounted accessories such as trays and respiratory equipment and secure them

in a safe place.

3. Use a ramp to drive the wheelchair in the luggage compartment of the vehicle:

• Set the wheelchair to the lowest speed setting.

• Operate the joystick to drive the wheelchair forwards up the ramps and into the vehicle.

Walk next to the wheelchair and follow it as it drives, but do NOT walk with it on the

ramps.

• Turn OFF the operating console.

4. If luggage and passenger compartments are NOT separated or enclosed, fasten the

wheelchair frame securely to the vehicle using the six-points strap-tie-down system (see

Figure 4).

To drive the wheelchair out of the vehicle:

1. FIRST, switch ON the operating console.

2. Put the wheelchair in free-wheel mode.

3. Stand on the ramps and pull the wheelchair towards you. Walking backwards, the

wheelchair will gently drive off the ramps.

2.4.4 Transport by vehicle, as seat for user

The wheelchair has passed the crash test of ISO 7176-19: 2008 and, as such, has been

designed and tested for use only as forward-facing seat in a motor vehicle.

The wheelchair is tested dynamically with the ATD (anthropomorphic test device) using a

six-points strap-tie system and a 3-point occupant-restraint system. Nevertheless, the user

should preferably be transferred to one of the seats inside the vehicle and use vehicle’s

restrain system. The wheelchair should be stored as luggage in a separate (cargo)

compartment, see §2.4.3

Risk of injuries and damage

Use wheelchair's pelvic belt and the applicable three-points belt in the vehicle to prevent

head and chest impacts with the vehicle.

Do not use postural supports to restrain the user in the vehicle unless they are labelled as

being in accordance with the requirements specified in ISO 7176-19:2008.

Following involvement in any type of vehicle collision, have your wheelchair inspected by

the specialist dealer or manufacturer’s representative before reuse.

Securing the wheelchair

1. Make sure that the vehicle has a suitable wheelchair six-points strap-tie-down and occupant-

restraint system conform ISO 10542, and that both systems are not frayed, contaminated,

damaged or broken.

2. Use the operating console to return your wheelchair to stable position, see §3.6.

3. Remove all mounted accessories such as trays and respiratory equipment and secure them

in a safe place. If not possible, secure them to the wheelchair but positioned away from the

occupant with energy-absorbing padding placed between tray and user.

4. Use a ramp to drive the wheelchair (with user) in the vehicle according to the instructions in

§3.2.1.

WARNING

Sigma, Sigma 230

2021-01

Before use

9

EN

NL

5. Position the user facing forward in the travelling direction, centrally between the tie-down rails

mounted in the floor of the vehicle.

6. Make sure that the user is sitting as upright as possible. If the user's condition prevents this,

carry out a risk assessment to evaluate the user's safety during transit.

7. Turn the operating console OFF and make sure that the free-wheel lever is in braking mode,

see §3.4.

8. The location of each securement point on the wheelchair is marked with the

following symbol:

9. Verify that the tiedown end-fitting is compatible with the wheelchair securement points.

10. Attach the front securement-strap hooks to the securement points (A+B) on the wheelchair

following the supplier instructions of the strap-system, see Figure 4.

11. Turn free-wheel lever in free-wheel position and roll the wheelchair backwards to pull the front

straps tight, see §3.4.

12. Attach the rear securement-strap hooks to the securement points (C+D+E+F) on the rear in

the same way.

13. Turn free-wheel lever back in braking position, see §3.4.

Front side Rear side

Securement points

Securing the user

1. Attach the wheelchair’s pelvic belt.

2. Attach the user-restraint belts of the vehicle according to

the instructions of the strap-system manufacturer.

Wear the pelvic belt low across the front of the pelvis,

so that the angle of the pelvic belt is within the

preferred zone of 30° to 75° to the horizontal, similar

to that shown in the figure.

A steeper (greater) angle within the preferred zone is

desirable.

Angle of pelvic belt

3. Adjust the belt tightly according to the instructions of the strap-system manufacturer,

consistent with the user's comfort.

4. Ensure that the restraint belt connects in a straight line to the anchor point in the vehicle and

that no bends in the belt are visible, for instance at the axle of the rear wheel.

A

B

C

F

E

D

Sigma, Sigma 230

2021-01

Before use

10

EN

NL

5. Position the seatbelt buckle so that the release button will not be contacted by wheelchair

components during a crash.

6. Make sure that belts are not twisted or held away from the body as shown in figure 6.

7. Make sure that the shoulder-belt restraints fit over the shoulders, see figure 7.

Belt restraints must not be held away

from the body by wheelchair

components such as armrests or

wheels.

Belt restraints make full contact with

shoulder, chest and pelvis.

Pelvic belt low on the pelvis near the

thigh-abdominal junction

Improper belt-restraint fit

Proper belt-restraint fit

2.5 First use and storage

Risk of battery damage

• Never completely discharge the battery.

• Do not interrupt the charging cycle; only disconnect the battery charger when the battery is

fully charged.

• Make sure that your wheelchair is stored dry to prevent mould to grow and damage the

upholstery. If necessary, use a protective cover.

• Check the technical details for storage, see chapter 5.

Ensure that the battery has been fully charged before using your wheelchair, ask your dealer if

this has already been done or not. To charge, follow the charging instructions in §3.8.

CAUTION

✓

Sigma, Sigma 230

2021-01

Using your wheelchair

11

EN

NL

3 Using your wheelchair

Risk of injuries

• First read previous chapters and inform yourself about the intended use. Do NOT use your

wheelchair unless you have read and fully understood all instructions.

• Also read the instructions in the operator console manual and battery charger!

• In case of doubts or questions, do not hesitate to contact your local specialist dealer, your care

provider or technical adviser to help you with this.

3.1 First ride

Risk of injuries and damage

• Always keep the swing range of footrest and operating console in mind to prevent bystanders

from being injured or objects from being damaged.

• Always unplug the battery charger from the wheelchair before starting to drive.

• Make sure that you are familiar with the operation of your wheelchair before using it in

crowded and possibly dangerous places. First exercise at a specious, open area with little

bystanders.

• Investigate the effects of shifting the centre of gravity on the behaviour of the wheelchair,

for example on up or down gradients, on laterally sloping ground, or when overcoming

obstacles. Obtain support from an attendant.

• The surface of the controller gets slightly warm during use.

• While driving backwards, the speed is reduced.

1. Make sure that:

• the wheelchair is on a flat surface;

• the battery is fully loaded, see § 3.8;

• The motor is coupled, see § 3.4;

• the tyres have the correct tyre pressure, see § 0;

• the wheelchair is adapted to your needs and comfort, see §3.7;

• you have the proper sitting position, see § 3.6.

2. Follow the instructions in the operating console manual.

3. Switch on your wheelchair.

4. Turn the speed control to the lowest speed setting.

5. Exercise how to drive and make adjustments to the wheelchair.

6. If you feel confident enough, you can try to drive at higher speed.

7. Now try to turn, in forward and backward direction. Repeat this a few times.

8. Make sure that your wheelchair stands stable, when ending the ride.

9. Switch off your wheelchair.

3.2 Driving outdoors

Risk of accident - Adjust your driving behaviour and speed.

• Take the local road traffic law into consideration; it may differ per country. This counts for

driving on pavements, unpaved roads or paved roadways.

• Do not drive on roads with heavy traffic.

• Take the weather conditions into consideration. Avoid driving by moist weather, extreme heat,

snow, black ice, freezing temperatures; see technical specifications in chapter 5.

WARNING

CAUTION

WARNING

Sigma, Sigma 230

2021-01

Using your wheelchair

12

EN

NL

• Even with your wheelchair lights on, it is not suitable to drive on public roads at poor visibility

(darkness, mist, twilight). Make sure that you are well visible, also during daylight hours, by

using fluorescent clothing and/or by using own lighting at the front and rear side of the

wheelchair.

• Be aware of other road users to whom your wheelchair may be an obstacle. Pay special

attention during turning and reversing. If you are not acquainted with how to drive backwards,

first practice in an open area. Indicate the direction you are intending to go before turning.

• Try to drive straight in small passages to prevent getting trapped.

• Keep the braking distance in mind. Be aware that the braking distance depends on speed,

surface, weather conditions, slope and weight of the user.

3.2.1 Cope with slopes, kerbs, obstacles or ramps

Risk of injuries by unexpected movement

• Use a restraining safety belt to secure yourself sitting in the wheelchair.

• Pay attention if the road is sandy, has soft ground, holes or gaps that may cause entrapment

of the wheels and/or decreasing of the traction of the mid wheel.

• Do NOT drive on slopes, obstacles, steps or kerbs larger than the size described in the

technical specifications in chapter 5. If steeper ramps can not be avoided, see the instructions

in §2.4.3.

• Always approach a kerb from the front.

• Do not put your wheelchair in free-wheel mode on a slope. The wheelchair may start moving,

causing injuries to you or bystanders.

• Do not use your wheelchair on an escalator or stairs.

• Only use ramps approved by Vermeiren and do not exceed their maximum load.

Risk of damage

• Always park your electric wheelchair on horizontal flat surfaces and on sites that are easily

accessible.

• If necessary, take a short run-up to speed up the wheelchair to mount a slope, obstacle, kerb

or ramp. Prevent that you or your wheelchair has to cope with a large recoil.

• Make sure that the wheelchair does not touch the ground or ramp due to the inclination of the

wheelchair.

• Be aware that the braking distance on downhill slopes can be significantly larger than on level

ground.

Procedure

• Start your drive according to the instructions in § 3.1, step 1.

• To move the wheelchair up or down stairs/steps, use lifting equipment or a ramp. If these are

not available, it can be lifted manually by at least three persons, grasping the frame firmly with

both hands. Do not use the backrest, footplate(s), armrests, or wheels to grasp the wheelchair.

• To cope with obstacles or inclinations:

1. Adjust the wheelchair to its most stable position, see § 3.6.

2. Drive as slow as possible to cope with the obstacle or inclination.

CAUTION

When you stop on a slope, the brake will work automatically to prevent the wheelchair from

running forward or backward.

Sigma, Sigma 230

2021-01

Using your wheelchair

13

EN

NL

3.3 Operating console

Risk of injuries or damage

• Be aware that the stability decreases when the wheelchair is adjusted from sitting-strait to

inclined position.

• Make sure there is enough space around the wheelchair to operate backrest and seat.

How to use the operating console is described in a specific user manual, enclosed with the

delivery of your wheelchair. If this manual is missing, contact your specialist dealer

immediately.

Put the joystick in the neutral (central) position before pressing the on/off button, otherwise

the electronics will be blocked. To release this block, switch the operating console off and

on again.

Technical protections

The operating console enables you to control all driving components and motors to adjust your

body position. For your own safety, and to prevent that the wheelchair gets damaged, movements

are monitored by the electronics. This may result in block of movement, speed decrease or

complete stop. Consult the user manual of the operating console for more information.

To avoid accidental battery run down, your wheelchair is equipped with an automatic power

shutdown system. This system switches off the operating console automatically when it is not

operated for a while. If this occurs, simply switch your console back on.

3.4 Brake and free-wheel lever

Risk of injuries or damage

• Only operate the free-wheel lever when your wheelchair is turned OFF. An attendant should

operate the free-wheel lever. NEVER operate it from sitting position.

• Do not use the free-wheel mode on slopes and inclinations, see symbol on motor:

Make sure that the free-wheel lever is in its braking position BEFORE switching the

wheelchair ON. Electromagnetic brakes do NOT function if the wheelchair is in free-wheel

mode. This is indicated on the operating console. Driving is not possible.

Your wheelchair is equipped with electromagnetic brakes. The working of the brakes depends on

the position of free-wheel lever (13).

The EM brakes function automatically, only if free-wheel lever (13)

is in braking position (A), see Figure 5. In this situation, the brakes

start braking if:

• the wheelchair is OFF;

• the wheelchair is ON and the joystick is released.

Releasing the joystick makes the wheelchair stop gently and

activates the brakes.

Operation of free-wheel lever:

• Turn lever clockwise (position B) to put the wheelchair in free-wheel mode. Now, the motor

is disconnected. The wheelchair can be moved manually.

• Turn lever anticlockwise (position A) to connect the motor to the drive. This should be done

before starting the wheelchair.

CAUTION

13

Sigma, Sigma 230

2021-01

Using your wheelchair

14

EN

NL

Braking position

Free-wheel position

Operating free-wheel lever

3.5 Battery switch

Your wheelchair is equipped with a battery switch (16) to interrupt the circuit between the power

module and batteries. The disconnection is used for safety during transport, maintenance and

repairs. It is also possible to remove the battery switch knob to prevent that the wheelchair is

moved during your absence.

Battery connected

Battery disconnected

Disconnector end position

Battery switch positions

Operation:

Turn the red battery switch (16)

• clockwise to “I” to connect the battery to the power module [C].

• anticlockwise to “0” to disconnect the battery [D].

• anticlockwise, passing “0” to its end position [E] and remove the knob from the switch.

3.6 Moving to/from wheelchair

Risk of injuries or damage

• In case you cannot perform the transfer in a safe manner, ask someone to assist you.

• Do not stand on the footplate(s) during transfer into or out of the wheelchair.

CAUTION

B

C

D

E

A

Sigma, Sigma 230

2021-01

Using your wheelchair

15

EN

NL

Transfer

1. Position the wheelchair as close as possible to you when sitting

in your chair, couch, seat or bed.

2. Apply the brakes by turning the free-wheel lever to braking

position, see § 3.4.

3. Use the operating console to move the backrest and seat to

sitting position, see user manual of the console.

4. Fold the footplate(s) upwards to prevent standing on them.

5. If necessary, turn one armrest back/up to make room, see

§ 3.7.1.

6. Transfer to/from the wheelchair using the strength of your arms

or with the help of attendant(s) or lifting equipment.

Sitting in the wheelchair

1. Sit down on the seat with your lower back against the backrest.

2. Turn the footplate(s) down and put your feet on the footplates.

3. Turn armrests down, if applicable.

4. Make sure that your upper legs are horizontal and that your feet are in a comfortable position.

Adjust if necessary, see § 3.7.4 and § 3.7.5.

5. Make sure that your arms are bent and are resting comfortably on the arm pads. Adjust if

necessary, see § 3.7.1 and § 3.7.2.

Adjusting to stable position

For transport purposes and when you need to negotiate obstacles, the wheelchair must be

adjusted to maximise its stability:

• Seat in horizontal position

• Backrest upright

• Armrests in bottom position

• Footplate folded up or adjusted to a higher position to prevent touching the obstacle.

• Operating console turned inwards.

3.7 Comfort adjustments

Risk of injuries or damage

• The following comfort adjustments can be done by the attendant or caretaker. All other

adjustments are done by your specialist dealer according to the installation instructions, see

preface.

• Always keep the swing range of footrest and operating console in mind to prevent bystanders

from getting injured or objects from being damaged.

• Make sure that your fingers, clothes, buckles don’t get trapped during adjustment.

3.7.1 Operator console

The operator console has a swivel system and can be turned

horizontally to the left/right.

Grab the control support (26) below the operator console and

move it left/right to the desired position.

CAUTION

26

Sigma, Sigma 230

2021-01

Using your wheelchair

16

EN

NL

31

3.7.2 Armrests

Position

The armrests can be turned backwards (up) to make it easier to

transfer to/from the seat.

1. Push lever (31) of the toothed clamp (30) slowly down. The arm

rest is unlocked (in bottom position).

2. Turn the armrest up/backwards to its end position.

3. Pull lever (31) up to close the toothed clamp. The armrest is

locked in end position.

Angle

The same procedure is used to change the angle of the

armrest:

1. Repeat previous step 1.

2. Next, hold the armrest in the desired position, while

locking it with the lever (31).

3. Repeat this for the second armrest.

4. Make sure that both armrests have the same angle.

5. Make sure that both armrests are firmly secured.

3.7.3 Arm pads

The arm pads (3) can be adjusted in height (stepless) and angle (7,5° step):

1. Turn the star knob (32) a few turns anticlockwise. To

adjust the angle, turn it four turns minimally.

2. Pull/push the arm pad lightly to adjust the height.

3. Hold the arm pad at the desired angle.

4. Turn the star knob clockwise until it is finger-tight.

5. Repeat this for the second arm pad.

6. Make sure that both arm pads are firmly secured.

3.7.4 Footrest B06

To remove

1. Pull footrest lever (27) and swing footrest (4) outwards.

2. Lift the footrest to remove it.

To install

1. Hold footrest (4) sideways and hang it in footrest support

(28).

2. Swing the footrest inwards until it clicks in position.

30

12

31

32

3

27

4

28

La pagina sta caricando ...

Vermeiren Sigma 230 Manuale utente

Questo manuale è adatto anche per

Vermeiren Sigma 230 Manuale utente

in altre lingue

Documenti correlati

Altri documenti