Pioneer DJ Equipment DJM-2000 Manuale utente

Marca: Pioneer

Modello: DJ Equipment DJM-2000

Categoria: Controller DJ

Tipo: Manuale utente

Questo manuale è adatto anche per

DJM-2000

DRB1497-B

DJM-2000

DJ MIXER

TABLE DE MIXAGE

DJ-MISCHPULT

MIXER PER DJ

DJ MENGPANEEL

MESA DE MEZCLAS DJ

DJ микшерный пульт

The Pioneer website listed above provides answers to frequently asked questions, information about

software, and other up-to-date data of assistance to our customers.

Le site Web de Pionner ci-dessus fournit des réponses aux questions souvent posées, des informations

au sujet des logiciels et d’autres données mises à jour afin de venir en aide à notre clientèle.

Auf der oben angegebenen Pioneer-Website werden unseren Kunden Antworten auf häufig gestellte

Fragen, Informationen über Software und weitere Unterstützung mit neuesten Daten angeboten.

http://www.prodjnet.com/support/

Operating Instructions

Mode d’emploi

Bedienungsanleitung

Istruzioni per l’uso

Handleiding

Manual de instrucciones

Инструкции по эксплуатации

DRB1497-B

Thank you for buying this Pioneer product. Please read through these operating instructions so you will know how to operate your model properly. After you have fin-

ished reading the instructions, put them away in a safe place for future reference.

In some countries or regions, the shape of the power plug and power outlet may sometimes differ from that shown in the explanatory drawings. However the method of

connecting and operating the unit is the same.

The exclamation point within an equilateral

triangle is intended to alert the user to the

presence of important operating and

maintenance (servicing) instructions in the

literature accompanying the appliance.

The lightning flash with arrowhead symbol,

within an equilateral triangle, is intended to

alert the user to the presence of uninsulated

“dangerous voltage” within the product’s

enclosure that may be of sufficient

magnitude to constitute a risk of electric

shock to persons.

CAUTION:

TO PREVENT THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE COVER (OR

BACK). NO USER-SERVICEABLE PARTS

INSIDE. REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

IMPORTANT

D3-4-2-1-1_A1_En

D3-4-2-1-2-2*_A1_En

Replacement and mounting of an AC plug on the power supply cord of this unit should be performed only by qualified

service personnel.

IMPORTANT: THE MOULDED PLUG

This appliance is supplied with a moulded three pin mains plug for your safety and convenience. A 10 amp fuse is fitted in this plug. Should the

fuse need to be replaced, please ensure that the replacement fuse has a rating of 10 amps and that it is approved by ASTA or BSI to BS1362.

Check for the ASTA mark or the BSI mark on the body of the fuse.

If the plug contains a removable fuse cover, you must ensure that it is refitted when the fuse is replaced. If you lose the fuse cover the plug

must not be used until a replacement cover is obtained. A replacement fuse cover can be obtained from your local dealer.

If the fitted moulded plug is unsuitable for your socket outlet, then the fuse shall be removed and the plug cut off and disposed of

safely. There is a danger of severe electrical shock if the cut off plug is inserted into any 13 amp socket.

If a new plug is to be fitted, please observe the wiring code as shown below. If in any doubt, please consult a qualified electrician.

IMPORTANT: The wires in this mains lead are coloured in accordance with the following code:

Blue : Neutral Brown : Live

As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in

your plug, proceed as follows;

The wire which is coloured BLUE must be connected to the terminal which is marked with the

letter N or coloured BLACK.

The wire which is coloured BROWN must be connected to the terminal which is marked with the

letter L or coloured RED.

How to replace the fuse: Open the fuse compartment with a screwdriver and replace the fuse.

If you want to dispose this product, do not mix it with general household waste. There is a separate collection system for used

electronic products in accordance with legislation that requires proper treatment, recovery and recycling.

Private households in the member states of the EU, in Switzerland and Norway may return their used electronic products free of charge to

designated collection facilities or to a retailer (if you purchase a similar new one).

For countries not mentioned above, please contact your local authorities for the correct method of disposal.

By doing so you will ensure that your disposed product undergoes the necessary treatment, recovery and recycling and thus prevent potential

negative effects on the environment and human health.

K058b_A1_En

DRB1497-B

WARNING

his equipment is not waterproof. To prevent a fire or

shock hazard, do not place any container filled with

liquid near this equipment (such as a vase or flower

pot) or expose it to dripping, splashing, rain or

moisture.

D3-4-2-1-3_A1_En

WARNING

Before plugging in for the first time, read the following

section carefully.

The voltage of the available power supply differs

according to country or region. Be sure that the

power supply voltage of the area where this unit

will be used meets the required voltage (e.g., 230 V

or 120 V) written on the rear panel.

D3-4-2-1-4*_A1_En

WARNING

o prevent a fire hazard, do not place any naked flame

sources (such as a lighted candle) on the equipment.

D3-4-2-1-7a_A1_En

VENTILATION CAUTION

When installing this unit, make sure to leave space

around the unit for ventilation to improve heat radiation

(at least 5 cm at rear, and 3 cm at each side).

WARNING

Slots and openings in the cabinet are provided for

ventilation to ensure reliable operation of the product,

and to protect it from overheating. To prevent fire

hazard, the openings should never be blocked or

covered with items (such as newspapers, table-cloths,

curtains) or by operating the equipment on thick carpet

or a bed.

D3-4-2-1-7b*_A1_En

Operating Environment

Operating environment temperature and humidity:

+5 °C to +35 °C (+41 °F to +95 °F); less than 85 %RH

(cooling vents not blocked)

Do not install this unit in a poorly ventilated area, or in

locations exposed to high humidity or direct sunlight (or

strong artificial light)

D3-4-2-1-7c*_A1_En

If the AC plug of this unit does not match the AC

outlet you want to use, the plug must be removed

and appropriate one fitted. Replacement and

mounting of an AC plug on the power supply cord of

this unit should be performed only by qualified

service personnel. If connected to an AC outlet, the

cut-off plug can cause severe electrical shock. Make

sure it is properly disposed of after removal.

The equipment should be disconnected by removing

the mains plug from the wall socket when left unused

for a long period of time (for example, when on

vacation).

D3-4-2-2-1a_A1_En

CAUTION

The POWER switch on this unit will not completely

shut off all power from the AC outlet. Since the power

cord serves as the main disconnect device for the

unit, you will need to unplug it from the AC outlet to

shut down all power. Therefore, make sure the unit

has been installed so that the power cord can be

easily unplugged from the AC outlet in case of an

accident. To avoid fire hazard, the power cord should

also be unplugged from the AC outlet when left

unused for a long period of time (for example, when

on vacation).

D3-4-2-2-2a*_A1_En

POWER-CORD CAUTION

Handle the power cord by the plug. Do not pull out the

plug by tugging the cord and never touch the power

cord when your hands are wet as this could cause a

short circuit or electric shock. Do not place the unit, a

piece of furniture, etc., on the power cord, or pinch the

cord. Never make a knot in the cord or tie it with other

cords. The power cords should be routed such that they

are not likely to be stepped on. A damaged power cord

can cause a fire or give you an electrical shock. Check

the power cord once in a while. When you find it

damaged, ask your nearest PIONEER authorized

service center or your dealer for a replacement.

S002*_A1_En

DRB1497-B

Contents

How to read this manual

The names of displays, menus, and buttons in this manual are enclosed in brack-

ets. (e.g. [MASTER] channel, [ON/

OFF], [File] menu)

Before start

Features ...........................................................................................................................5

What’s in the box .............................................................................................................5

Connections

Rear Panel .......................................................................................................................6

Connecting input terminals ...........................................................................................7

Connecting output terminals .........................................................................................7

Connecting to the control panel ....................................................................................8

Connecting a computer ..................................................................................................8

About the USB audio driver software ............................................................................8

Operations

Control Panel .................................................................................................................11

Basic Operation ............................................................................................................12

Advanced Operations ...................................................................................................14

List of MIDI Messages ..................................................................................................18

Types of BEAT EFFECT ..................................................................................................22

Changing the settings

Setting preferences .......................................................................................................24

About the auto standby function .................................................................................24

Additional information

Troubleshooting ............................................................................................................25

About the liquid crystal display ....................................................................................26

About the exemption clauses ......................................................................................26

Block Diagram...............................................................................................................27

Specifications ................................................................................................................28

DRB1497-B

English

Before start

Features

This unit is a high-performance DJ mixer designed for professional DJs, which,

in addition to its high sound quality design, is equipped with a multi-touch panel

and various types of interface and effect functions enabling new styles of DJ

performing.

TOUCH PANEL EFFECT

This unit uses a large 5.8-inch LCD multi-touch panel. When the

[FREQUENCY MIX] and [SIDECHAIN REMIX] effect functions are combined, the

effect can be checked both visually and aurally, enabling intuitive control.

 FREQUENCY MIX

The track frequencies are divided into seven bands and displayed graphically.

Fader control on the touch panel makes it easier to grasp the details and mix two

channels or swap instruments (parts).

 SIDECHAIN REMIX

The sound of a specific channel can be used as the trigger to apply effects to the

sound of other channels. Operation of the touch panel’s pad makes it possible to

process sound dynamically.

INST FX

This unit is equipped with six types of effects (NOISE, ZIP, CRUSH, JET, HPF, LPF).

Effects can be obtained simply by turning the [FILTER] controls for the differ-

ent channels for improvisational performances, and the desired effects can be

achieved by adjusting the [PARAMETER] control.

BEAT EFFECT

The DJM series’ well-received BEAT EFFECT function has been carried over and

further evolved. This unit is equipped with an [EFFECT FREQUENCY] function

allowing the amount of the effect applied to be adjusted by frequency range, for

even greater playing freedom than before.

PRO DJ LINK

When a PRO DJ LINK-compatible Pioneer DJ player (CDJ-2000, CDJ-900 etc.),

a computer on which rekordbox is installed and this unit are connected by LAN

cable, the PRO DJ LINK functions below can be used.

For details, see About PRO DJ LINK on page 14.

 SD & USB Export

 rekordbox LINK Export

 LIVE SAMPLER

 LINK MONITOR

 STATUS INFORMATION

SOUND CARD

This unit is equipped with sound card/

USB audio interface allowing up to four

audio sources from one computer to be assigned to the different channels and

mixed. Furthermore, the master channel output signals can be output to the

computer, a great convenience for example for recording the mixed sound.

HIGH SOUND QUALITY

Measures have been taken to improve sound quality for both the digital and

analog inputs and outputs. Sound processing with 96 kHz sampling, a 24-bit

high sound quality A/

D converter and a 32-bit high sound quality D/

A converter

achieves more powerful, higher grade sound.

This unit supports 48 kHz 16 bit, 48 kHz 24 bit and 44.1 kHz 16 bit USB audio

signals.

What’s in the box

! CD-ROM

! USB Cable

! LAN cables x 4

! Power cable

! Warranty card

! Operating instructions (this document)

DRB1497-B

Connections

Be sure to turn off the power and unplug the power cord from the power outlet whenever making or changing connections.

Refer to the operating instructions for the component to be connected.

Connect the power cord after all the connections between devices have been completed.

Be sure to use the included power cord.

Rear Panel

CH 2CH 3CH 4

CH 1

SIGNAL GND

PHONO

MIDI OUTUSB

CDLINE

CONTROL

OUTIN

(TRS)

RL(MONO) RL(MONO)

DIGITAL

BOOTHSENDRETURN

COMPUTER 1

COMPUTER 2

LINK

CH 3CH 1

CH 4CH 2

CH 2CH 3CH 4CH 1

DIGITAL

SIGNAL GND

1GND

-6dB -3dB 0dB

2HOT

3COLD

PHONO

POWER

AC IN

OFF

MASTER1

MASTER

ATT.

MASTER2REC OUT

DIGITAL CD DIGITAL

CDLINE

CONTROL

CD DIGITAL

1 2 63 345 2345 a

7 85 6 3 759

fgkhijl

1 POWER (page 12)

Turns this unit’s power on and off.

2 PHONO (page 7)

Connect to a phono level (MM cartridge) output device. Do not input line level

signals.

3 CD (page 7)

Connect to a DJ player or a line level output component.

4 SIGNAL GND (page 7)

Connect an analog player’s ground wire here. This helps reduce noise when

the analog player is connected.

5 CD, DIGITAL (page 12)

Selects the analog signal input terminals (CD) or the digital signal input

terminals (DIGITAL IN).

6 LINE (page 7)

Connect to a cassette deck or a line level output component.

7 CONTROL (page 7)

Connect using a control cord (included with Pioneer DJ players).

8 DIGITAL OUT (page 7)

Outputs the master channel audio signals.

9 DIGITAL IN (page 7)

Connect these to the digital coaxial output terminals on DJ players, etc. The

sound may be momentarily interrupted when the output signal sampling

frequency is switched.

a Kensington security slot

b USB (page 8)

Connect to a computer.

c MIDI OUT (page 7)

Connect this to the MIDI IN terminal on an external MIDI sequencer.

d LINK (page 7)

Connect these to the LINK terminals on Pioneer DJ players or the LAN ports

of computers on which rekordbox is installed (PRO DJ LINK).

e RETURN (page 7)

Connect to the output terminal of an external effector. When the [L (MONO)]

channel only is connected, the [L (MONO)] channel input is simultaneously

input to the [R] channel.

f SEND (page 7)

Connect to the input terminal of an external effector. When the [L (MONO)]

channel only is connected, a monaural audio signal is output.

g BOOTH (page 7)

Output terminals for a booth monitor, compatible with balanced or unbal-

anced output for a TRS connector.

h REC OUT (page 7)

This is an output terminal for recording.

i MASTER2 (page 7)

Connect to a power amplifier, etc.

j MASTER ATT.

Switches the attenuation level of the sound output from the [MASTER1] and

[MASTER2] terminals. Select 0 dB, –3 dB or –6 dB.

k MASTER1 (page 7)

Connect to a power amplifier, etc.

l AC IN

Connect to a power outlet using the included power cord. Wait until all con-

nections between the equipment are completed before connecting the power

cord.

Be sure to use the included power cord.

DRB1497-B

English

Connecting input terminals

CH 2CH 3CH 4

CH 1

SIGNAL GND

PHONO

MIDI OUTUSB

CDLINE

CONTROL

OUTIN

(TRS)

RL(MONO) RL(MONO)

DIGITAL

BOOTH SEND RETURN

LINK

CH 2CH 3CH 4CH 1

DIGITAL

SIGNAL GND

1GND

-6dB -3dB 0dB

2HOT

3COLD

PHONO

POWEROFF

MASTER1

MASTER

ATT.

MASTER2REC OUT

DIGITAL CD DIGITAL

CDLINE

CONTROL

CD DIGITAL

COMPUTER 1

COMPUTER 2

CH 3CH 1

CH 4CH 2

AC IN

PRO DJ LINK

Computers

Pioneer DJ players

To power outlet

Pioneer DJ players

rekordbox rekordbox

Digital audio output device

Analog player

Cassette deck, CD player, etc.

(line level output devices)

Analog player

1 For details on PRO DJ LINK, see About PRO DJ LINK on page 14.

Use the included LAN cables to connect to Pioneer DJ players.

2 To use the fader start function, connect a LAN cable or control cord (page 13).

Connecting output terminals

CH 2CH 3CH 4

CH 1

SIGNAL GND

MIDI OUTUSB

OUT IN

(TRS)

RL(MONO) RL(MONO)

DIGITAL

BOOTHSENDRETURN

LINK

CH 2CH 3CH 4CH 1

SIGNAL GND

1GND

-6dB -3dB 0dB

2HOT

3COLD

PHONO

POWEROFF

MASTER1

MASTER

ATT.

MASTER2REC OUT

DIGITAL

CDLINE

CONTROL

CD DIGITAL

PHONO

DIGITAL

CDLINE

CONTROL

CD DIGITAL

CH 3CH 1

CH 4CH 2

AC IN

COMPUTER 1

COMPUTER 2

Power amplifierTo power outlet

Digital audio

input device

Power amplifier

(for booth monitor)

External effector

MIDI sequencer

Cassette deck, etc.

(analog input recording device)

Power amplifier

1 Also connect the external effector to the [RETURN] terminal (input terminal).

DRB1497-B

Connecting to the control panel

HEADPHONES

CUE

MONO SPLIT STEREO

CUE

MASTER

PHONES

LEVEL

MIXING

THRU

CROSS FA DER ASS

/DIGITAL PHONO

USB 1/2

TRIM

MIC

OVER

- 1

- 2

- 3

- 5

- 7

ISO

EQ/

MID

LOW

-26/

-12

+12

OFF ON OVER

TALK

MIC

LEVEL

-12

+12

/DIGITAL

ISO

EQ/

-26

Microphones

Headphones

Connecting a computer

CH 2

CH 1

SIGNAL GND

PHONO

MIDI OUTUSB

CDLINE

CONTROL

ONO)

CH 3

LINK

CH 1

COMPUTER 1

COMPUTER 2

CH 4

CH 2

DIGITALCD DIGITAL

Computer

Connect with the included USB cable.

About the USB audio driver software

This driver software is a proprietary program for inputting and outputting audio

signals from the computer. To use this unit connected to a computer on which

a Windows or Mac OS is installed, install the driver software on the computer

beforehand.

Software Use Agreement

This software usage agreement (hereafter referred to as “the agreement”) deter-

mines matters related to use of the DJ function software (hereafter referred to

as “the software”) between the customer and Pioneer Corporation (hereafter

referred to as “Pioneer”).

Be sure to read the following articles carefully before installing and using the

software. Use of the software implies that the customer has consented to the

agreement. If you do not consent to the agreement, do not install or use the

software.

[Usage agreement]

On the condition of complying with the contents of this agreement, the customer

has permission to install and use this software on a single personal computer.

[Restrictions]

The customer shall not create, distribute or send reproductions of this software

over networks or from one computer to another. In addition, the customer shall

not modify, sell, lend, transfer or resell the software, nor distribute, create, etc.,

secondary works of the software. Furthermore, the customer shall not reverse

compile, reverse engineer, reverse assemble or otherwise change the software

into formats perceptible by humans.

[Copyrights, etc.]

Copyrights and all other intellectual property rights related to this software are

the property of Pioneer and its affiliates. This software is protected by copyright

laws and the provisions of international treaties.

[Repudiation of guarantee and technical support]

This software and all associated documentation, etc., is provided on an “as is”

basis. Pioneer does not guarantee the customer nor third parties regarding

merchantability, compatibility with specific purposes, violation of rights of oth-

ers or any other matters, nor does it guarantee technical support related to this

software or associated documentation. Note that repudiation of guarantee may

not be not recognized in some countries and regions by mandatory provisions, in

which case this repudiation of guarantee may not apply. The customer’s rights

may differ in some countries and regions.

[Limitation of liability]

Pioneer and other suppliers of this software shall accept no responsibility

whatsoever for damages incurred through use of or inability to use this software

or any associated documentation (including but not limited to loss of profits,

business interruptions, damages resulting from loss or impairment of informa-

tion, etc.), even if Pioneer has been notified of the possibility of such damages.

Limitation of liability related to incidental or direct damages may not be recog-

nized in some countries and regions by mandatory provisions, in which case this

limitation of liability may not apply. Note that, regardless of the case, the respon-

sibility of Pioneer and its subsidiaries regarding this software shall not exceed

the sum paid by the customer to Pioneer or its subsidiaries. This repudiation of

limitation of liability is a fundamental element of the arrangement between the

customer and Pioneer.

[Governing law]

This agreement complies with the laws and ordinances of Japan and shall be

interpreted accordingly. This agreement stipulates all articles of the arrangement

between the customer and Pioneer, and shall be applied with priority over any

prior and existing agreements related to this matter (regardless of whether oral

or in writing). The Tokyo District Court shall be the court of exclusive jurisdiction

in first instance for any disputes arising regarding this agreement.

Cautions on Installation

! Before installing the driver software, be sure to turn off the power of this unit

and disconnect the USB cable from both this unit and your computer.

! If you connect this unit to your computer without installing the driver soft-

ware first, an error may occur on your computer depending on the system

environment.

! If you have discontinued the installation process in progress, step through

the installation process again from the beginning according to the following

procedure.

! Read Software Use Agreement carefully before installing this unit’s propri-

etary driver software.

! Before installing the driver software, terminate all other programs running on

your computer.

! The driver software is compatible with the following OSs.

— Mac OS X (10.3.9 and later)

— Windows Vista

Home Basic/

Home Premium/

Ultimate/

Business

— Windows

XP Home Edition/

Professional (SP2 or later)

DRB1497-B

English

The driver support is not compatible with 64-bit versions of operating sys-

tems (64-bit editions of Windows Vista

and Windows

XP Professional x64

Edition).

! The included CD-ROM includes installation programs in the following 12

languages.

English, French, German, Italian, Dutch, Spanish, Portuguese, Russian,

Simplified Chinese, Traditional Chinese, Korean, and Japanese

When using operating systems in other languages, follow the instructions on

the screen to select [English (English)].

Installing the driver software

 Installation Procedure (Windows)

Read Cautions on Installation carefully before installing the driver software.

! To install or uninstall the driver software, you need to be authorized by the

administrator of your computer. Log on as the administrator of your computer

before proceeding with the installation.

1 Insert the included CD-ROM into the computer’s CD drive.

The CD-ROM folder appears.

! If the CD-ROM folder is not displayed after a CD-ROM is loaded, open the CD

drive from [Computer (or My Computer)] in the [START] menu.

2 Double-click [DJM-2000_X.XXX.exe].

The driver installation screen appears.

3 When the language selection screen appears, select [English]

and click [OK].

You can select one from multiple languages depending on the system environ-

ment of your computer.

4 Carefully read the Software Use Agreement and if you

consent to the provisions, put a check mark in [I agree.] and click

[OK].

If you do not consent to the provisions of the Software Use Agreement, click

[Cancel] and stop installation.

5 Proceed with installation according to the instructions on the

screen.

If [Windows Security] appears on the screen while the installation is in progress,

click [Install this driver software anyway] and continue with the installation.

! When installing on Windows XP

If [Hardware Installation] appears on the screen while the installation is in

progress, click [Continue Anyway] and continue with the installation.

! When the installation program is completed, a completion message appears.

! When the installation of the driver software is completed, you need to reboot

your computer.

 Installation Procedure (Macintosh)

Read Cautions on Installation carefully before installing the driver software.

! To install or uninstall the driver software, you need to be authorized by the

administrator of your computer. Have the name and password of the adminis-

trator of your computer ready in advance.

1 Insert the included CD-ROM into the computer’s CD drive.

The CD-ROM folder appears.

! Double-click the CD icon on the desktop when folders are not displayed after

a CD-ROM has been loaded.

2 Double-click [DJM-2000_M_X.X.X.dmg].

The [DJM-2000AudioDriver] menu screen appears.

3 Double-click [DJM-2000AudioDriver.pkg].

The driver installation screen appears.

4 Check the details on the screen and click [Continue Anyway].

5 When the Software Use Agreement screen appears, select

[English], carefully read the Software Use Agreement and click

[Continue Anyway].

You can select one from multiple languages depending on the system environ-

ment of your computer.

6 If you consent to the provisions of the Software End User

License Agreement, click [Agree].

If you do not consent to the provisions of the Software Use Agreement, click [I

disagree] and stop installation.

7 Proceed with installation according to the instructions on the

screen.

! Click [Cancel] to cancel installation after it has started.

! When the installation of the driver software is completed, you need to reboot

your computer.

Connecting the DJM-2000 and computer

1 Connect this unit to your computer via a USB cable.

This unit functions as an audio device conforming to the ASIO standards.

! When using ASIO-compatible applications, [USB 1/2], [USB 3/4], [USB 5/6]

and [USB 7/8] can be used as inputs. Depending on the input/

output setting,

it is possible to use three of this unit’s sets of inputs.

! When using DirectX-compatible applications, only [USB 1/

2] can be used as

the input.

! The computer’s recommended operating environment depends on the DJ

application. Be sure to check the recommended operating environment for

the DJ application you are using.

! When another USB audio device is connected to the computer at the same

time, it may not operate or be recognized normally.

We recommend only connecting the computer and this unit.

! When connecting the computer and this unit, we recommend connecting

directly to this unit’s USB port.

2 Press [POWER].

Turn on the power of this unit.

! The message [Installing device driver software] may appear when the DJM-

2000 is connected to the computer for the first time or when it is reconnected

to the computer’s USB port. Wait until the [Your devices are ready for use]

message appears.

! When installing on Windows XP

— [Can Windows connect to Windows Update to search for software?]

may appear while the installation is in progress. Select [No, not this

time] and click [Next] to continue with the installation.

— [What do you want the wizard to do?] may appear while the instal-

lation is in progress. Select [Install the software automatically

(Recommended)] and click [Next] to continue with the installation.

— If [Windows Security] appears on the screen while the installation is in

progress, click [Install this driver software anyway] and continue with

the installation.

Switching the input/

output setting

Use this procedure to switch the computer’s input/

output setting when using the

driver software.

! If applications using this unit as the default audio device (DJ applications,

etc.) are running, quit those applications before switching the input/

output

setting.

! Some time is required after the input/

output setting is switched for the com-

puter to be updated. The input/

output setting cannot be switched while the

computer is being updated.

! Sound may not be output if there are differences between the input/

output

settings on this unit and on the computer. If this happens, turn this unit’s

power on and reset the input/

output settings with the USB cable connected.

! If the input/

output setting is switched while using DirectX, the application

may not recognize the driver software.

! MIDI communications are interrupted if the input/

output setting is switched

during MIDI communications.

 Switching procedure (Windows)

Click the Windows [START] menu>

[All Programs]

[Pioneer]

[DJM-2000]

[DJM-2000 Setting Utility].

Switch the computer’s input/

output setting.

— ASIO 4 outputs 0 inputs 16 bits DirectX 1 output 0 inputs

— ASIO 3 outputs 1 input 16 bits DirectX 1 output 1 input

— ASIO 3 outputs 0 inputs 24 bits DirectX 1 output 0 inputs

 Switching procedure (Macintosh)

Click [Apple]

[System Preferences]

[Other]

[DJM-2000 Settings].

Switch the computer’s input/

output setting.

— 8-channel output No input 16 bits

— 6-channel output 2-channel input 16 bits

— 6-channel output No input 24 bits

Adjusting the buffer size (Windows)

Use this procedure to adjust the computer’s buffer size when using ASIO driver

software.

Click the Windows [START] menu>

[All Programs]

[Pioneer]

[DJM-2000]

[DJM-2000 Setting Utility].

A sufficiently large buffer size decreases the chance of sound dropout (sound

interruption) but increases audio signal transmission delay (latency).

! If applications using this unit as the default audio device (DJ applications,

etc.) are running, quit those applications before adjusting the buffer size.

DRB1497-B

Checking the version of the driver software

 Procedure for checking (Windows)

Click the Windows [START] menu>

[All Programs]

[Pioneer]

[DJM-2000]

[DJM-2000 Version Display Utility].

The [Version] screen appears.

 Procedure for checking (Macintosh)

Click [Apple]

[About This Mac]

[More Info]

[Extensions]

[DJM-

2000 USBAudio].

The [Version] screen appears.

Checking the latest information on the driver

software

For the latest information on the driver software for exclusive use with this unit,

visit our website shown below.

http://www.prodjnet.com/support/

DRB1497-B

English

Operations

Control Panel

OVER

POWER

/DIGITAL PHONO

USB 1/2

TRIM

SELECT

EFFECT SELECT

EFFECT FREQUENCY

1 2 3 4

OFF

MASTER

LINK

HEADPHONES

MIC

INST FX

MIDI

CURVE SETTING

- 1

- 2

- 3

- 5

- 7

- 10

- 15

- 24

BALANCE

LOW

TIME

LIVE

SAMPLER

WAKE UP

LEVEL/DEPTH

1/8

1/4 1/2 3/4 1/1 2/1 4/1

MIN MAX

MIN

MAX

AUTO

/TAP

TA P

ON/OFF

CUE

DELAY

ECHO

FILTER

GATE

ROLL

TRANS

REVERB

MULT I TAP

DELAY

PHASER

SLIP

ROLL

SEND/

RETURN

REV

ROLL

CUE

NOISE JET

ZIP HPF

CRUSH LPF

MONO

ON/OFF

CH EQ

CROSS FADER

CH FADER

ISOLATOR

START/STOP

SNAPSHOT

UTILITY

BOOTH MONITOR

STEREO

MONO SPLIT STEREO

DJM-

2000

FILTER

PARAMETER

MINMAX

OVER

- 1

- 2

- 3

- 5

- 7

- 10

- 15

- 24

ISO

EQ/

LOW

MID

LOW

MIN

MAX

CUE

MASTER

PHONES

LEVEL

MIXING

-26/

-12

+12

OFF ON OVER

TALK

PROFESSIONAL MIXER

THRU

CROSS FA DER ASSIGN

THRU

CROSS FADER ASSIGN

MIC

LEVEL

CUE

FILTER

MINMAX

CUE

FILTER

MINMAX

CUE

FILTER

MINMAX

-12

+12

/DIGITAL LINE

USB 3/4

OVER

- 1

- 2

- 3

- 5

- 7

- 10

- 15

- 24

- 1

- 2

- 3

- 5

- 7

- 10

- 15

- 24

ISO

EQ/

ISO

EQ/

TRIM

-26/

MID

-26/

LOW

-26/

/DIGITAL LINE

USB 5/6

TRIM

-26/

MID

-26/

LOW

-26/

OVER

- 1

- 2

- 3

- 5

- 7

- 10

- 15

- 24

ISO

EQ/

/DIGITAL PHONO

USB 7/8

TRIM

-26/

MID

-26/

LOW

-26/

OVER

MIC

A B M

MID

MIN MAX

MIDI

MIX

REMIX

e e ee

1 Microphone input jack (page 13)

2 MIC LEVEL (page 13)

3 EQ (HI, LOW) (page 13)

4 OFF, ON, TALK OVER (page 13)

5 INST FX (page 15)

6 PARAMETER (page 15)

7 CUE (page 12)

8 MONO SPLIT, STEREO (page 12)

9 MIXING (page 12)

a LEVEL (page 12)

b PHONES (page 12)

c CD/DIGITAL, PHONO, LINE, USB */* (page 12)

d TRIM (page 12)

e EQ/ISO (HI, MID, LOW) (page 12)

f Channel Level Indicator (page 12)

g FILTER (page 15)

h Channel Fader (page 12)

i CROSS FADER ASSIGN (A, THRU, B) (page 12)

j CH SELECT (page 16)

k EFFECT SELECT (page 16)

l EFFECT FREQUENCY (HI, MID, LOW) (page 16)

m Beat buttons (page 16)

n TIME (page 16)

o LEVEL/

DEPTH (page 16)

p AUTO/TAP (page 16)

q TAP (page 16)

r ON/

OFF (BEAT EFFECT) (page 16)

s LIVE SAMPLER (UTILITY, WAKE UP) (page 15, page 24)

t MIDI (page 16)

u MIX (page 14)

v REMIX (page 14)

w ON/

OFF (TOUCH PANEL EFFECT) (page 14)

DRB1497-B

x Crossfader (page 12)

y MASTER (page 12)

z Master Level Indicator (page 12)

A BALANCE (page 13)

B MONO, STEREO (page 13)

C BOOTH MONITOR (page 13)

D START/

STOP (SNAPSHOT) (page 16)

E ON/

OFF (MIDI) (page 16)

F CH EQ (ISOLATOR, EQ) (page 12)

G CH FADER (

, ) (page 13)

H CROSS FADER (

, , ) (page 13)

Basic Operation

Outputting sound

1 Press [POWER].

Turn on the power of this unit.

2 Switching the [CD/DIGITAL, PHONO, LINE, USB */*] switch

Select the input sources for the different channels from among the devices con-

nected to this unit.

— [CD/DIGITAL]: Selects the DJ player connected to the [CD] terminals. To

select the DJ player connected to the [DIGITAL IN] terminal, set the [CD,

DIGITAL] switch on the rear panel to [DIGITAL].

— [PHONO]: Selects the analog player connected to the [PHONO]

terminals.

— [LINE]: Selects the cassette deck or CD player connected to the [LINE]

terminals.

— [USB */*]: Selects the sound of the computer connected to the [USB]

port.

3 Rotate [TRIM].

Adjusts the level of audio signals input in each channel.

The corresponding channel level indicator lights when audio signals are being

properly input to that channel.

4 Set the channel fader to the inner position.

Adjusts the level of audio signals output in each channel.

5 Switch the [CROSS FADER ASSIGN (A, THRU, B)] switch.

Switches the output destination of each channel.

— [A]: Assigns to [A] (left) of the crossfader.

— [B]: Assigns to [B] (right) of the crossfader.

— [THRU]: Choose this when you do not want to use the crossfader. (The

signals do not pass through the crossfader.)

6 Set the crossfader.

This operation is not necessary when [CROSS FADER ASSIGN (A, THRU, B)] is set

to [THRU].

7 Turn the [MASTER] control.

Audio signals are output from the [MASTER1] and [MASTER2] terminals.

The master level indicator lights.

Adjusting the sound quality

Turn the [EQ/ISO (HI, MID, LOW) ] controls for the individual

channels.

Refer to Specifications on page 28 for the range of sound that can be adjusted by

each control.

 Switching the [EQ/ISO (HI, MID, LOW)] function.

Switch the [CH EQ (ISOLATOR, EQ)] switch.

— [ISOLATOR]: The isolator function is set. The indicator lights.

— [EQ]: The equalizer function is set.

Monitoring sound with headphones

1 Connect headphones to the [PHONES] jack.

2 Press [CUE] for the channel to be monitored.

3 Switch the [MONO SPLIT, STEREO] switch.

— [MONO SPLIT]: The sound of the channel for which [CUE] is pressed is

output from the headphones output’s left channel, while the sound of

[MASTER] is output from the right channel.

— [STEREO]: The sound of the channel for which [CUE] is pressed is output

in stereo from the headphones.

4 Turn the [MIXING] control.

This adjusts the balance of the monitor volume between the sound of the channel

for which [CUE] is pressed and the [MASTER] channel sound.

5 Turn the [LEVEL] control for [HEADPHONES].

Sound is output from the headphones in the channel selected by [CUE].

! Monitoring is canceled when [CUE] is pressed again.

! When [LIVE SAMPLER] is turned on, [CUE] button for the TOUCH PANEL

EFFECT and [CUE] button for the [LINK] cannot be pressed simultaneously.

DRB1497-B

English

1312

Monitoring the sound of the computer

1 Connect headphones to the [PHONES] jack.

2 Connect a computer on which rekordbox is installed.

For instructions on connections, see Connecting input terminals on page 7.

3 Selecting the track to be monitored with rekordbox

4 Press [CUE] button for [LINK].

The track selected with rekordbox is output from the headphones.

! Monitoring is canceled when [CUE] is pressed again.

! The same operation as at Monitoring sound with headphones (steps 3 to 5)

can be performed.

Switching the fader curve

 Select the channel fader curve characteristics.

Switch the [CH FADER (

, )] switch.

— [ ]: The curve rises suddenly at the back side.

— [ ]: The curve rises gradually (the sound gradually increases as the

channel fader is moved away from the front side).

 Select the crossfader curve characteristics.

Switch the [CROSS FADER (

, , )] switch.

— [ ]: Makes a sharply increasing curve (if the crossfader is moved away

from the [A] side, audio signals are immediately output from the [B]

side).

— [ ]: Makes a curve shaped between the two curves above and below.

— [ ]: Makes a gradually increasing curve (if the crossfader is moved

away from the [A] side, the sound on the [B] side gradually increases,

while the sound on the [A] gradually decreases).

Starting playback on a DJ player using the fader

(fader start)

When connected to a Pioneer DJ player by LAN cable (included with this unit) or

control cord (included with the DJ player), operations such as starting playback

on the DJ player can be controlled with this unit’s fader.

Connect this unit and Pioneer DJ player beforehand. For instructions on connec-

tions, see Connecting input terminals on page 7.

 Start playback using the channel fader

1 Set [CROSS FADER ASSIGN (A, THRU, B)] to [THRU].

2 Set [FADER START] to [ON].

For instructions on setting, see Changing the settings on page 24.

3 Set the channel fader to the outermost position.

4 Set the cue on the DJ player.

The DJ player pauses playback at the cue point.

5 Set the channel fader to the inner position.

Playback starts on the DJ player.

! If you set the channel fader back to the original position, the player instanta-

neously returns to the cue point already set and pauses playback (back cue).

 Start playback using the crossfader

1 Set [CROSS FADER ASSIGN (A, THRU, B)] to [A] or [B].

2 Set [FADER START] to [ON].

For instructions on setting, see Changing the settings on page 24.

3 Set the crossfader.

Set to the edge opposite the side on which the channel you want to use with the

fader start function is set.

4 Set the cue on the DJ player.

The DJ player pauses playback at the cue point.

5 Set the crossfader.

Playback starts on the DJ player.

! If you set the crossfader back to the original position, the player instanta-

neously returns to the cue point already set and pauses playback (back cue).

Using a microphone

1 Connect the microphone to the microphone input jack.

2 Set [OFF, ON, TALK OVER] to [ON] or [TALK OVER].

— [ON]: The indicator lights.

— [TALK OVER]: The indicator flashes.

! When set to [TALK OVER], sound other than that from the [MIC] terminal is

attenuated by 20 dB (default value) when sound of –15 dB (default value) or

greater is input to the microphone.

3 Turn the [MIC LEVEL] control.

This adjusts the audio level output from the [MIC] terminal.

! Pay attention that rotating to the extreme right position outputs a very loud

sound.

4 Input audio signals to the microphone.

 Adjusting the sound quality

Turn the [EQ (HI, LOW)] control for [MIC] channel.

Refer to Specifications on page 28 for the range of sound that can be adjusted by

each control.

Switching between monaural and stereo audio

This switches the sound output from the [MASTER1], [MASTER2], [BOOTH], [REC

OUT], [PHONES], [DIGITAL OUT] and [USB] terminals between monaural and

stereo.

Switch the [MONO, STEREO] switch.

— [MONO]: Outputs monaural audio.

— [STEREO]: Outputs stereo audio.

 Adjusting the L/

R balance of audio

The left/

right balance of the sound output from the [MASTER1], [MASTER2],

[BOOTH], [REC OUT], [PHONES], [DIGITAL OUT] and [USB] terminals can be

adjusted.

1 Set the [MONO, STEREO] switch to [STEREO].

2 Rotate [BALANCE].

The L/

R balance of audio varies according to the rotation direction and position

of the [BALANCE] control.

! Rotating to the rightmost position outputs only the right sound of stereo

audio. Rotating to the leftmost position outputs only the left sound of stereo

audio.

Audio is output from the [BOOTH] terminal

Rotate [BOOTH MONITOR].

Adjusts the level of audio signals output at the [BOOTH] terminal.

DRB1497-B

Advanced Operations

About PRO DJ LINK

When a PRO DJ LINK-compatible Pioneer DJ player (CDJ-2000, CDJ-900 etc.),

a computer on which rekordbox is installed and this unit are connected by LAN

cable, the PRO DJ LINK functions below can be used.

For more details on the PRO DJ LINK function, also refer to the DJ player’s han-

dling instructions and rekordbox’s operating instructions.

For instructions on connections, see Connecting input terminals on page 7.

! Up to four DJ players can be connected. Up to two computers can be

connected.

! Connect the DJ players to the [LINK] terminal ([CH1] to [CH4]) with the same

number as the channel to which the audio cables are connected.

! Connect the computers to the [COMPUTER 1] or [COMPUTER 2] terminal.

 SD & USB Export

rekordbox music files and management data on SD memory cards/

USB devices

connected to a CDJ-2000, CDJ-900, etc., can be transferred between DJ players.

 rekordbox LINK Export

This function lets you transfer rekordbox music files and management data

directly, eliminating the bother of exporting the data to an SD memory card/

USB

device.

 LIVE SAMPLER

The sound input to the [MIC] terminal or output from the [MASTER] terminals

can be sampled and played on a DJ player.

 LINK MONITOR

With this function, rekordbox music files stored on the computer can be quickly

monitored over the headphones.

 STATUS INFORMATION

This function informs the DJ players of the connected channel status (on-air

status, channel number, etc.).

FREQUENCY MIX

The currently playing sound is divided into seven frequency bands that are dis-

played graphically. Fader control on the touch panel makes it easier to grasp the

details and mix two channels or swap instruments (parts).

LINK

These light when DJ players are properly connected to the

[LINK] terminals.

These light when the fader start function is turned on.

Channel assign buttons These select the channels to be mixed.

Volume level display

The input volume level to this function is displayed in a light

color, the output volume level from this function is displayed

in a dark color.

Touch fader

These adjust the volume balance of the channels to be

mixed for the separate frequency bands.

<< >>

These move the touch fader immediately to the left or right

edge.

 To mix [CH2] and [CH3]:

Prepare this unit in advance so that the sound of [CH3] is being output from the

[MASTER] terminals.

1 Set the [CROSS FADER ASSIGN (A, THRU, B)] switches for [CH2]

and [CH 3] to [THRU].

! Set the [CROSS FADER ASSIGN (A, THRU, B)] switches of the channels to be

mixed to [THRU].

! When using the crossfader, it is recommended to set it to the center position.

2 Press [MIX].

The [FREQUENCY MIX] screen appears on the touch panel.

3 Press the channel assign buttons to select [CH2] for the left

side, [CH3] for the right side.

The volume levels for the individual frequency bands of the sound playing in

[CH3] are displayed on the right half of the touch panel.

4 Press all the [ >> ] buttons.

All the touch faders move to the right edge.

5 Press [ON/

OFF].

This turns the effect on.

[ON/

OFF] flashes when the effect is turned on.

6 Move the channel fader for [CH2] to the back side.

The volume levels for the individual frequency bands of the sound playing in

[CH2] are displayed on the left half of the touch panel.

7 Move the touch fader to the left side.

The sound of the frequency bands whose crossfaders have been moved is mixed

and output.

! The effect turns off when [ON/

OFF] is pressed again.

! To switch from the [FREQUENCY MIX] to the [SIDECHAIN REMIX] mode, first

press the [ON/

OFF] button to turn the effect off, then press [REMIX].

SIDECHAIN REMIX

When this function is used, the sound of the specified frequency band for the

specified channel can be used as the trigger to apply effects to the sounds of

other channels.

This selects the channel to which the effect is applied.

HOLD

This holds the effect’s parameter information (the position

at which the control area was touched).

EFFECT

This selects the type of effect.

LEVEL/

DEPTH

Use this to adjust the amount of the effect applied.

EXIT

Use this to close the [TRIGGER] menu.

TRIGGER (SAMPLING/

TRIGGER)

Use this to open the [TRIGGER] menu.

TRIGGER BAND

Use these to select the frequency band to be used as the

trigger.

Control area Use this to change the effect’s parameters.

TRIGGER CH (SAM-

PLING/

TRIGGER CH)

This selects the channel to be used as the effect trigger.

Trigger indicators

These flash according to the automatically detected rhythm

for the different frequency bands.

 To set the channel for sampling and triggering to [CH3]

and mix the sampled sound with the sound of [CH2] for

output:

Prepare this unit in advance so that the sound of [CH2] is being output from the

[MASTER] terminals.

1 Press [REMIX].

The [SIDECHAIN REMIX] screen appears on the touch panel.

DRB1497-B

English

1514

2 Press the [2] button in the [CH] section.

This selects the channel to which the effect is applied.

3 Press [EFFECT] and select [SAMPLER].

This selects the type of effect.

Effect Name Descriptions

OSCILLATOR1 – 4

Sound is created inside this unit, mixed to the sound of the channel

selected in the [CH] section, then output according to the [TRIGGER CH

(SAMPLING/

TRIGGER CH)] trigger.

SAMPLER

The sound of the channel selected at [TRIGGER CH (SAMPLING/

TRIG-

GER CH)] is sampled, mixed to the sound of the channel selected in the

[CH] section, then output according to the [TRIGGER CH (SAMPLING/

TRIGGER CH)] trigger.

PITCH

The pitch of the sound of the channel selected in the [CH] section is

changed, mixed with the channel selected in the [CH] section, then out-

put according to the [TRIGGER CH (SAMPLING/

TRIGGER CH)] trigger.

GATE

The sound input at [CH] is output according to the [TRIGGER CH (SAM-

PLING/

TRIGGER CH)] trigger.

! It is not possible to select multiple effects simultaneously.

4 Press [TRIGGER (SAMPLING/

TRIGGER)].

The [TRIGGER] menu appears.

5 At [TRIGGER CH (SAMPLING/

TRIGGER CH)], select [CH3].

This selects the channel to be used as the effect trigger.

! When [SAME] is pressed, the same channel as the one selected in the [CH]

section is selected as the trigger.

6 At [TRIGGER BAND], press [MID] and [HI].

This selects the frequency band set as the effect trigger.

Only [LOW] (the bass sound) is selected.

7 Press [ON/

OFF].

This turns the effect on.

[ON/

OFF] flashes when the effect is turned on.

8 Touch the control area.

[ ] appears at the point at which the panel was touched.

The [CH3] sound at the point in the control area that was touched is sampled.

Triggered by the low frequency sound of [CH3], the sampled sound is mixed with

the sound of [CH2] (which is continuing to play normally) and output from the

[MASTER] terminals.

The effect changes when the position touched in the control area is changed.

! The effect turns off when [ON/

OFF] is pressed again.

! The sampled sound is only valid while the control area is being touched.

! To switch from the [SIDECHAIN REMIX] to the [FREQUENCY MIX] mode, first

press the [ON/

OFF] button to turn the effect off, then press [MIX].

 Using [HOLD]

When [HOLD] is turned on, effect’s parameter information is held even if the effect is

turned off. The parameter information is cleared when [HOLD] is turned off.

! The parameter information and sampled sound are cleared when the effect is

switched.

LIVE SAMPLER

The sound input to the [MIC] terminal or the sound output from the [MASTER]

terminals can be sampled and played on a PRO DJ LINK–compatible Pioneer DJ

player.

Connect this unit and PRO DJ LINK-compatible Pioneer DJ player in advance.

For instructions on connections, see Connecting input terminals on page 7.

SOURCE SELECT

Select the source to be sampled here.

REC VOLUME

Use these to adjust the volume for recording.

The volume can be adjusted in the range –9 dB to +9 dB.

Status indicator

This indicates this unit’s status and whether or not sam-

pling data is available.

Waveform display This displays the sound as a waveform.

Playing address display

This displays the sound as a bar graph.

This is only displayed when previewing the sound.

Slider

The sound is played from the position at which the touch

panel was touched.

This is only displayed when previewing the sound.

PRE-REC SAVE

The sound is sampled from a point 8 seconds before the

button was pressed.

REC (REC STOP)

The sound is sampled for up to 8 seconds from the point at

which the button is pressed.

PREVIEW (STOP)

Use this to preview the sampled sound over the head-

phones.

 Sampling the sound being played

1 Press [LIVE SAMPLER].

The [LIVE SAMPLER] screen appears on the touch panel.

2 Press [MIC] or [MASTER] in the [SOURCE SELECT].

This selects the channel to be sampled.

3 Press [REC (REC STOP)].

The sound of the channel selected at step 2 is sampled from the point at which

[REC (REC STOP)] was pressed.

! Sampling is possible for up to 8 seconds.

! Sampling stops automatically once 8 seconds have elapsed after [REC

(REC STOP)] was pressed.

4 Press [REC (REC STOP)].

Sampling stops. The sample saving screen is displayed.

 Sampling the sound from the point 8 seconds before

1 Press [LIVE SAMPLER].

The [LIVE SAMPLER] screen appears on the touch panel.

2 Press [MIC] or [MASTER] in the [SOURCE SELECT].

This selects the channel to be sampled.

3 Press [PRE-REC SAVE].

The sound for the channel selected in step 2 is sampled from the point 8 seconds

before [PRE-REC SAVE] was pressed.

! Sampling is possible for up to 8 seconds.

 Previewing the sampled sound

1 Press the [CUE] button to the left of the touch panel.

2 Press [PREVIEW (STOP)].

The position being played is displayed at the playing address and slider displays.

! When the touch panel’s slider is touched, the sampled sound is played from

that position.

 Playing the sampled sound on the DJ player

Use PRO DJ LINK to access this unit from the DJ player.

The sampled sound (audio file) can be loaded and played on the DJ player.

INST FX

This effect changes in association with the [FILTER] controls for the individual

channels.

1 Press one of the [INST FX] buttons.

This selects the type of effect.

The button that was pressed flashes.

! The same effect is set for [CH1] to [CH4].

2 Turn the [FILTER] control.

The effect is applied to the channel(s) for which the control(s) was (were)

pressed.

Effect Name Descriptions

FILTER (parameter 1)

PARAMETER

(parameter 2)

NOISE

White noise generated

inside this unit is mixed

in to the sound of the

channel via the filter

and output.

Sets the cut-off

frequency for the

filter through which the

white noise passes.

Sets the volume of the

white noise.

ZIP

Lowers the pitch of the

channel’s sound for

output.

Sets the amount of

pitch shifting for lower-

ing the pitch.

Sets the balance

between the original

sound and the effect

sound.

CRUSH

Changes the channel’s

sound to a crushed

sound for output.

Sets the degree by

which the input sound

is crushed.

The further the control

is turned clockwise,

the more the effect is

stressed.

JET

Adds a flanger effect for

output.

Sets the flanger effect.

The further the control

is turned clockwise,

the more the effect is

stressed.

DRB1497-B

Effect Name Descriptions

FILTER (parameter 1)

PARAMETER

(parameter 2)

HPF

Outputs the sound

through the high-pass

filter.

Sets the filter’s cut-off

frequency.

The further the control

is turned clockwise,

the more the effect is

stressed.

LPF

Outputs the sound

through the low-pass

filter.

Sets the filter’s cut-off

frequency.

The further the control

is turned clockwise,

the more the effect is

stressed.

 Adjusting the effect of the effect sound

Turn the [PARAMETER] control.

The further the control is turned clockwise, the more the effect is stressed. When

turned all the way counterclockwise, the effect is minimum.

BEAT EFFECT

This function lets you instantaneously set various effects according to the tempo

(BPM = Beats Per Minute) of the currently playing track.

AUTO (TAP)

[AUTO] lights when the BPM measurement mode is set to

the auto mode.

[TAP] lights when in the manual input mode.

BPM value display (3

digits)

When in the auto mode, this displays the automatically

detected BPM value.

When the BPM cannot be detected, the previously detected

BPM value is displayed and flashes.

When in the manual input mode, this displays the BPM

value that was input manually.

BPM

This is always lit.

% (ms)

These light according to the units for the different effects.

1 Press [AUTO/TAP].

Select the BPM measurement mode.

— AUTO: The BPM is automatically measured from the input audio signal.

AUTO is set when this unit’s power is turned on.

— TAP: The BPM is input manually by tapping [TAP].

! The BPM measurement range when AUTO is selected is 70 to 180. Depending

on the track, it may not be possible to properly measure the BPM. If not, the

BPM value flashes on the display. In this case, use the [TAP] button to input

the BPM manually.

2 Press one of the [CH SELECT] buttons.

This selects the channel to which the effect is applied.

— [1] – [4]: The effect is applied to the sounds of channels [CH1] – [CH4].

— [MIC]: The effect is applied to the sound of the [MIC] channel.

— [A], [B]: The effect is applied to the sound of the crossfader’s [A] (left) or

[B] (right) side.

— [M]: The effect is applied to the sound of the [MASTER] channel.

3 Press one of the [EFFECT SELECT] buttons.

This selects the type of effect.

! For the types of effects, see Types of BEAT EFFECT on page 22.

! When [SEND/RETURN] is selected, see Using the external effector below.

4 Press one of the beat buttons.

This selects the beat fraction for synchronizing the effect sound.

The effect time corresponding to the beat fraction is set automatically.

! The beat fraction can be changed by turning [TIME] while pressing the beat

button.

5 Press [ON/

OFF].

The effect is applied to the sound.

The effect’s time parameter can be adjusted by turning the [TIME] control.

The effect’s quantity parameter can be adjusted by turning the [LEVEL/

DEPTH]

control.

[ON/

OFF] flashes when the effect is turned on.

! The effect turns off when [ON/

OFF] is pressed again.

 Inputting the BPM manually

Tap the [TAP] button at least two times with a finger in (quarter

note) beat with the currently playing sound.

The average value of the intervals at which the [TAP] button was tapped is set as

the BPM.

! When the BPM is set using the [TAP] button, the beat fraction is set to 1/1,

and the time of one beat (one quarter note) is set as the effect time.

! The BPM can be set manually by turning the [TIME] control while pressing

the [TAP] button.

! The BPM can be set manually by pressing the beat button while pressing

[TAP].

! The BPM can be set in units of 0.1 by turning [TIME] while pressing [TAP] and

[AUTO/TAP].

 Adjusting the amount of effect applied for different

frequency bands

Turn the [EFFECT FREQUENCY (HI, MID, LOW)] control.

See Types of BEAT EFFECT on page 22 for the parameters of the effects that can

be adjusted with the different controls.

 Using the external effector

1 Connect this unit and external effector.

[SEND/RETURN] lights.

For instructions on connections, see Connecting output terminals on page 7.

! [SEND/RETURN] does not light when nothing is connected to the [RETURN]

terminal.

2 Press one of the [CH SELECT] buttons.

This selects the channel to which the effect is applied.

3 Press [SEND/RETURN].

[SEND/RETURN] flashes.

4 Press [ON/

OFF].

The sound that has passed through the external effector is output.

! The effect turns off when [ON/

OFF] is pressed again.

! If the [SEND/RETURN] terminal connection is canceled when [RETURN] is on,

[ON/

OFF] turns off and [DELAY] is selected at [EFFECT SELECT].

Using the MIDI function

 Operating the DJ software

The DJM-2000 also outputs the operating data for the buttons and dials in MIDI

format. If you connect a computer with a built-in MIDI-compatible DJ software

via a USB cable, you can operate the DJ software on this unit.

Install the DJ software on your computer in advance. Also, adjust audio and MIDI

settings for the DJ software.

! For MIDI channel setting instructions, see Changing the settings on page 24.

1 Connect this unit’s [USB] terminal to the computer.

For details about connections, see Connecting a computer on page 8.

2 Start the DJ software.

3 Press [ON/

OFF] in the [MIDI] section.

Turn the MIDI function on.

Transmission of the MIDI messages begin.

! When the faders and controls are moved, messages are sent according to the

positions of the faders and controls. For messages output by this unit, see

List of MIDI Messages on page 18.

! MIDI messages for the positions of all the buttons, faders and controls can

be sent in a single batch by pressing the [START/

STOP] button for at least 2

seconds (Snapshot function).

! The MIDI timing clock (BPM information) is sent regardless of [ON/

OFF].

! When [ON/

OFF] in the [MIDI] section is pressed again, sending of MIDI mes-

sages stops.

 Sending the MIDI start and MIDI stop messages

Press [START/

STOP] in the [MIDI] section.

! The MIDI start and MIDI stop messages are sent alternately each time the

[START/

STOP] button is pressed, regardless of whether the MIDI function is

on or off.

Using the MIDI control screens

This unit is equipped with four types of MIDI control screens. Use them accord-

ing to your DJ software.

1 Press the [MIDI] button to the right of the touch panel.

The [MIDI CONTROL] screen appears on the touch panel.

2 Select a type, from [TYPE A] to [TYPE D].

This selects the type of MIDI control screen.

! When [PAGE1] or [PAGE2] is pressed, the page being displayed switches.

DRB1497-B

English

1716

3 Operate the touch panel buttons or faders.

Transmission of the MIDI messages begin.

For messages output by this unit, see List of MIDI Messages on page 18.

Operating an external MIDI sequencer

This unit sends the tempo of the currently playing source (BPM information)

as the MIDI timing clock. This can be used to synchronize an external MIDI

sequencer with the tempo of the source.

! External MIDI sequencers not supporting MIDI timing clocks cannot be

synchronized.

! External MIDI sequencers cannot be synchronized for sources for which the

BPM cannot be measured stably.

! MIDI timing clocks are output even for BPM values input manually by tapping

the [TAP] button with a finger. The MIDI timing clock output range is 40 BPM

to 250 BPM.

1 Connect the [MIDI OUT] terminal to the external MIDI

sequencer’s MIDI IN terminal using a commercially available MIDI

cable.

2 Set the external MIDI sequencer’s sync mode to Slave.

3 Press [START/

STOP].

The MIDI start message is sent.

4 Press [ON/

OFF] in the [MIDI] section.

Transmission of the MIDI messages begin.

DRB1497-B

List of MIDI Messages

Control Panel

Category SW Name SW Type

MIDI Messages

Trigger/

Toggle Notes

MSB LSB

CH1

TRIM

VR Bn 01 dd — — — — 0-127

VR Bn 02 dd — — — — 0-127

MID

VR Bn 03 dd — — — — 0-127

LOW

VR Bn 04 dd — — — — 0-127

FILTER

VR Bn 05 dd — — — — 0-127

Channel fader VR Bn 11 dd — — — — 0-127

CROSS FADER ASSIGN

SW Bn 41 dd — — — — 0, 64, 127

CUE

BTN Bn 46 dd — — — Trigger/

Toggle OFF=0, ON=127

CH2

TRIM

VR Bn 06 dd — — — — 0-127

VR Bn 07 dd — — — — 0-127

MID

VR Bn 08 dd — — — — 0-127

LOW

VR Bn 09 dd — — — — 0-127

FILTER

VR Bn 0A dd — — — — 0-127

Channel fader VR Bn 12 dd — — — — 0-127

CROSS FADER ASSIGN

SW Bn 42 dd — — — — 0, 64, 127

CUE

BTN Bn 47 dd — — — Trigger/

Toggle OFF=0, ON=127

CH 3

TRIM

VR Bn 0C dd — — — — 0-127

VR Bn 0E dd — — — — 0-127

MID

VR Bn 0F dd — — — — 0-127

LOW

VR Bn 15 dd — — — — 0-127

FILTER

VR Bn 16 dd — — — — 0-127

Channel fader VR Bn 13 dd — — — — 0-127

CROSS FADER ASSIGN

SW Bn 43 dd — — — — 0, 64, 127

CUE

BTN Bn 48 dd — — — Trigger/

Toggle OFF=0, ON=127

CH4

TRIM

VR Bn 50 dd — — — — 0-127

VR Bn 51 dd — — — — 0-127

MID

VR Bn 5C dd — — — — 0-127

LOW

VR Bn 52 dd — — — — 0-127

FILTER

VR Bn 53 dd — — — — 0-127

Channel fader VR Bn 14 dd — — — — 0-127

CROSS FADER ASSIGN

SW Bn 44 dd — — — — 0, 64, 127

CUE

BTN Bn 49 dd — — — Trigger/

Toggle OFF=0, ON=127

Crossfader Crossfader VR Bn 0B dd — — — — 0-127

CURVE SETTING

CH EQ (ISOLATOR, EQ) SW Bn 21 dd — — — — 0, 127

CH FADER (

)

SW Bn 5E dd — — — — 0, 127

CROSS FADER (

, ,

)

SW Bn 5F dd — — — — 0, 64, 127

MASTER

BALANCE

VR Bn 17 dd — — — — 0-127

MASTER level VR Bn 18 dd — — — — 0-127

CUE

BTN Bn 4A dd — — — Trigger/

Toggle OFF=0, ON=127

BOOTH MONITOR

VR Bn 19 dd — — — — 0-127

CH SELECT

BTN Bn 22 dd — — — Trigger/

Toggle

OFF=0, ON=127

BTN Bn 23 dd — — — Trigger/

Toggle

OFF=0, ON=127

BTN Bn 24 dd — — — Trigger/

Toggle

OFF=0, ON=127

BTN Bn 25 dd — — — Trigger/

Toggle

OFF=0, ON=127

MIC

BTN Bn 26 dd — — — Trigger/

Toggle

OFF=0, ON=127

BTN Bn 27 dd — — — Trigger/

Toggle

OFF=0, ON=127

BTN Bn 28 dd — — — Trigger/

Toggle

OFF=0, ON=127

BTN Bn 29 dd — — — Trigger/

Toggle

OFF=0, ON=127

BEAT EFFECT

TIME

VR Bn 0D MSB Bn 2D LSB —

TIME value (half the

value when FILTER or

PHASER is selected for

EFFECT SELECT)

ON/

OFF BTN Bn 40 dd — — — Trigger/

Toggle OFF=0, ON=127

AUTO/

TAP

BTN Bn 45 dd — — — Trigger/

Toggle OFF=0, ON=127

CUE

BTN Bn 4B dd — — — Trigger/

Toggle OFF=0, ON=127

TAP

BTN Bn 4E dd — — — Trigger/

Trigger OFF=0, ON=127

LEVEL/

DEPTH VR Bn 5B dd — — — — 0-127

DRB1497-B

English

1918

Category SW Name SW Type

MIDI Messages

Trigger/

Toggle Notes

MSB LSB

EFFECT SELECT

DELAY

BTN Bn 2A dd — — — Trigger/

Toggle

OFF=0, ON=127

MULTI TAP DELAY

BTN Bn 2B dd — — — Trigger/

Toggle

OFF=0, ON=127

ROLL

BTN Bn 2E dd — — — Trigger/

Toggle

OFF=0, ON=127

REV ROLL

BTN Bn 2F dd — — — Trigger/

Toggle

OFF=0, ON=127

TRANS

BTN Bn 35 dd — — — Trigger/

Toggle

OFF=0, ON=127

GATE

BTN Bn 3D dd — — — Trigger/

Toggle

OFF=0, ON=127

ECHO

BTN Bn 37 dd — — — Trigger/

Toggle

OFF=0, ON=127

REVERB

BTN Bn 36 dd — — — Trigger/

Toggle

OFF=0, ON=127

SLIP ROLL

BTN Bn 3A dd — — — Trigger/

Toggle

OFF=0, ON=127

FILTER

BTN Bn 3B dd — — — Trigger/

Toggle

OFF=0, ON=127

PHASER

BTN Bn 39 dd — — — Trigger/

Toggle

OFF=0, ON=127

SEND/

RETURN

BTN Bn 3E dd — — — Trigger/

Toggle

OFF=0, ON=127

EFFECT FRE-

QUENCY

VR Bn 66 dd — — — — 0-127

MID

VR Bn 67 dd — — — — 0-127

LOW

VR Bn 68 dd — — — — 0-127

INST FX

NOISE

BTN Bn 55 dd — — — Trigger/

Toggle

OFF=0, ON=127

ZIP

BTN Bn 56 dd — — — Trigger/

Toggle

OFF=0, ON=127

CRUSH

BTN Bn 57 dd — — — Trigger/

Toggle

OFF=0, ON=127

JET

BTN Bn 69 dd — — — Trigger/

Toggle

OFF=0, ON=127

HPF

BTN Bn 6A dd — — — Trigger/

Toggle

OFF=0, ON=127

LPF

BTN Bn 6B dd — — — Trigger/

Toggle

OFF=0, ON=127

PARAMETER

VR Bn 6C dd — — — — 0-127

MIC

VR Bn 1E dd — — — — 0-127

LOW

VR Bn 1F dd — — — — 0-127

HEADPHONES

LEVEL

VR Bn 1A dd — — — — 0-127

MIXING

VR Bn 1B dd — — — — 0-127

LINK CUE

BTN Bn 73 dd — — — Trigger/

Toggle OFF=0, ON=127

Touch panel

control

CUE

BTN Bn 6E dd — — — Trigger/

Toggle OFF=0, ON=127

MIDI

BTN Bn 6F dd — — — Trigger/

Toggle OFF=0, ON=127

MIX

BTN Bn 70 dd — — — Trigger/

Toggle

OFF=0, ON=127

REMIX

BTN Bn 71 dd — — — Trigger/

Toggle

OFF=0, ON=127

ON/

OFF BTN Bn 72 dd — — — Trigger/

Toggle OFF=0, ON=127

MIDI

START

BTN FA — — — — — — —

STOP

BTN FC — — — — — — —

1 When turning one button on switches another button from on to off, MIDI on and off messages are sent from the two buttons.

When there is no button that switches off, only the MIDI on message is sent from the button that was pressed.

Touch panel

 FREQUENCY MIX, SIDECHAIN REMIX

Category SW Name SW Type

MIDI Messages

Trigger/

Toggle Notes

MSB LSB

FREQUENCY MIX

Touch fader 1 VR Bn 38 dd — — — —

0 - 127 (very top of

screen)

Touch fader 2 VR Bn 4C dd — — — — 0-127

Touch fader 3 VR Bn 4D dd — — — — 0-127

Touch fader 4 VR Bn 74 dd — — — — 0-127

Touch fader 5 VR Bn 75 dd — — — — 0-127

Touch fader 6 VR Bn 76 dd — — — — 0-127

Touch fader 7 VR Bn 77 dd — — — —

0 - 127 (very bottom of

screen)

SIDECHAIN

REMIX

X axis of control area VR Bn 1C dd — — — — 0-127

Y axis of control area VR Bn 3C dd — — — — 0-127

LEVEL/

DEPTH VR Bn 31 dd — — — — 0-127

CH1

BTN 9n 49 dd — — — Trigger/

Toggle OFF=0, ON=127

CH2

BTN 9n 4A dd — — — Trigger/

Toggle OFF=0, ON=127

CH3

BTN 9n 4B dd — — — Trigger/

Toggle OFF=0, ON=127

CH4

BTN 9n 4C dd — — — Trigger/

Toggle OFF=0, ON=127

TRIGGER CH (SAMPLING/

TRIGGER CH) SAME BTN 9n 51 dd — — — Trigger/

Toggle OFF=0, ON=127

TRIGGER CH (SAMPLING/

TRIGGER CH) CH1 BTN 9n 52 dd — — — Trigger/

Toggle OFF=0, ON=127

TRIGGER CH (SAMPLING/

TRIGGER CH) CH2 BTN 9n 53 dd — — — Trigger/

Toggle OFF=0, ON=127

TRIGGER CH (SAMPLING/

TRIGGER CH) CH3 BTN 9n 54 dd — — — Trigger/

Toggle OFF=0, ON=127

TRIGGER CH (SAMPLING/

TRIGGER CH) CH4 BTN 9n 55 dd — — — Trigger/

Toggle OFF=0, ON=127

TRIGGER BAND LOW BTN 9n 59 dd — — — Trigger/

Toggle OFF=0, ON=127

TRIGGER BAND MID BTN 9n 5A dd — — — Trigger/

Toggle OFF=0, ON=127

TRIGGER BAND HI BTN 9n 5B dd — — — Trigger/

Toggle OFF=0, ON=127

DRB1497-B

 MIDI CONTROL

Pioneer DJ Equipment DJM-2000 Manuale utente

Marca: Pioneer

Modello: DJ Equipment DJM-2000

Categoria: Controller DJ

Tipo: Manuale utente

Questo manuale è adatto anche per

DJM-2000

Scarica il pdf

rapporto

in altre lingue

français: Pioneer DJ Equipment DJM-2000 Manuel utilisateur
español: Pioneer DJ Equipment DJM-2000 Manual de usuario
Deutsch: Pioneer DJ Equipment DJM-2000 Benutzerhandbuch
Nederlands: Pioneer DJ Equipment DJM-2000 Handleiding

Pioneer DJ Equipment DJM-2000 Manuale utente

Questo manuale è adatto anche per

Pioneer DJ Equipment DJM-2000 Manuale utente

in altre lingue

Documenti correlati

Altri documenti