Tascam DR-70D Manuale del proprietario

DR-70D

Linear PCM Recorder for DSLR

D01244000E

ENGLISH

FRANÇAIS

ESPAÑOL

DEUTSCH

ITALIANO

日本語

OWNER'S MANUAL

MODE D’EMPLOI

MANUAL DEL USUARIO

BEDIENUNGSANLEITUNG

MANUALE DI ISTRUZIONI

取扱説明書

2 TASCAM DR-70D

TEAC CORPORATION

https://tascam.jp/jp/

1-47 Ochiai, Tama-shi, Tokyo 206-8530 Japan

TEAC AMERICA, INC.

https://tascam.com/us/

Phone: +1-323-726-0303

10410 Pioneer Blvd. Suite #1 and #4, Santa Fe Springs,

California 90670, U.S.A.

TEAC UK Ltd.

https://tascam.eu/

Phone: +44-1923-797205

Meridien House, 69-71 Clarendon Road, Watford, Herts,

WD17 1DS, United Kingdom

TEAC EUROPE GmbH

https://tascam.de/

Phone: +49-611-71580

Bahnstrasse 12, 65205 Wiesbaden-Erbenheim, Germany

TEAC SALES & TRADING(SHENZHEN) CO., LTD

Phone: +86-755-88311561~2

Room 817, Block A, Hailrun Complex, 6021 Shennan Blvd.,

Futian District, Shenzhen 518040, China

• TASCAM is a trademark of TEAC CORPORATION, registered

in the U.S. and other countries.

• SDXC Logo is a trademark of SD-3C, LLC.

• Microsoft, Windows and Windows Vista are either registered

trademarks or trademarks of Microsoft Corporation in the

United States and/or other countries.

• Apple, Macintosh, Mac OS and Mac OS X are trademarks of

Apple Inc.

• Blackfin® and the Blackfin logo are registered trademarks of

Analog Devices, Inc.

• Other company names, product names and logos in this

document are the trademarks or registered trademarks of

their respective owners.

TASCAM DR-70D 3

Owner’s Manual

IMPORTANT SAFETY PRECAUTIONS

INFORMATION TO THE USER

This equipment has been tested and found to comply with the limits for a Class

B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instruction manual,

may cause harmful interference to radio communications. However, there is

no guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following

measures.

a) Reorient or relocate the receiving antenna.

b) Increase the separation between the equipment and receiver.

c) Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

d) Consult the dealer or an experienced radio/TV technician for help.

CAUTION

Changes or modifications to this equipment not expressly approved by TEAC

CORPORATION for compliance could void the user’s authority to operate this

equipment.

For U.S.A.

For Canada

THIS CLASS B DIGITAL APPARATUS COMPLIES WITH CANADIAN ICES-003.

CET APPAREIL NUMERIQUE DE LA CLASSE B EST CONFORME A LA NORME

NMB-003 DU CANADA.

Declaration of Conformity

Responsible party : TEAC AMERICA, INC.

Address : 10410 Pioneer Blvd. Suite #1 and #4,

Santa Fe Springs, California 90670, U.S.A.

Telephone number : 1-323-726-0303

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) this device may not cause harmful interference,

and (2) this device must accept any interference received, including inter-

ference that may cause undesired operation.

DECLARATION OF CONFORMITY

We, TEAC EUROPE GmbH. Bahnstrasse 12, 65205 Wiesbaden-Er-

benheim, Germany declare in own responsibility, the TEAC

product described in this manual is in compliance with the

corresponding technical standards.

IMPORTANT SAFETY INSTRUCTIONS

1 Read these instructions.

2 Keep these instructions.

3 Heed all warnings.

4 Follow all instructions.

5 Do not use this apparatus near water.

6 Clean only with dry cloth.

7 Do not block any ventilation openings. Install in accordance with the

manufacturer’s instructions.

8 Do not install near any heat sources such as radiators, heat registers, stoves,

or other apparatus (including amplifiers) that produce heat.

9 Do not defeat the safety purpose of the polarized or grounding-type plug. A

polarized plug has two blades with one wider than the other. A grounding

type plug has two blades and a third grounding prong. The wide blade or

4 TASCAM DR-70D

the third prong are provided for your safety. If the provided plug does not

fit into your outlet, consult an electrician for replacement of the obsolete

outlet.

10 Protect the power cord from being walked on or pinched particularly at

plugs, convenience receptacles, and the point where they exit from the

apparatus.

11 Only use attachments/accessories specified by the manufacturer.

12 Use only with the cart, stand,

tripod, bracket, or table specified by the manufac-

turer, or sold with the apparatus. When a cart is used,

use caution when moving the cart/apparatus

combination to avoid injury from tip-over.

13 Unplug this apparatus during lightning storms or

when unused for long periods of time.

14 Refer all servicing to qualified service personnel. Servicing is required when

the apparatus has been damaged in any way, such as power-supply cord

or plug is damaged, liquid has been spilled or objects have fallen into the

apparatus, the apparatus has been exposed to rain or moisture, does not

operate normally, or has been dropped.

• The apparatus draws nominal non-operating power from the AC outlet with

its POWER or STANDBY/ON switch not in the ON position.

• The mains plug is used as the disconnect device, the disconnect device shall

remain readily operable.

• Caution should be taken when using earphones or headphones with the

product because excessive sound pressure (volume) from earphones or

headphones can cause hearing loss.

• If you are experiencing problems with this product, contact TEAC for a service

referral. Do not use the product until it has been repaired.

CAUTION

• Do not expose this apparatus to drips or splashes.

• Do not place any objects filled with liquids, such as vases, on the apparatus.

• Do not install this apparatus in a confined space such as a book case or similar

unit.

• The apparatus should be located close enough to the AC outlet so that you

can easily grasp the power cord plug at any time.

• If the product uses batteries (including a battery pack or installed batteries),

they should not be exposed to sunshine, fire or excessive heat.

• CAUTION for products that use replaceable lithium batteries: there is danger

of explosion if a battery is replaced with an incorrect type of battery. Replace

only with the same or equivalent type.

CAUTIONS ABOUT BATTERIES

This product uses batteries. Misuse of batteries could cause a leak, rupture or

other trouble. Always abide by the following precautions when using batteries.

• Never recharge non-rechargeable batteries. The batteries could rupture or

leak, causing fire or injury.

• When installing batteries, pay attention to the polarity indications (plus/minus

(¥/^) orientation), and install them correctly in the battery compartment as

indicated. Putting them in backward could make the batteries rupture or leak,

causing fire, injury or stains around them.

• When you store or dispose batteries, isolate their terminals with insulation

tape or something like that to prevent them from contacting other batteries

or metallic objects.

• When throwing used batteries away, follow the disposal instructions indicated

on the batteries and the local disposal laws.

• Do not use batteries other than those specified. Do not mix and use new

and old batteries or different types of batteries together. The batteries could

rupture or leak, causing fire, injury or stains around them.

• Do not carry or store batteries together with small metal objects. The batteries

could short, causing leak, rupture or other trouble.

• Do not heat or disassemble batteries. Do not put them in fire or water.

Batteries could rupture or leak, causing fire, injury or stains around them.

• If the battery fluid leaks, wipe away any fluid on the battery case before

inserting new batteries. If the battery fluid gets in an eye, it could cause loss

of eyesight. If fluid does enter an eye, wash it out thoroughly with clean water

without rubbing the eye and then consult a doctor immediately. If the fluid

gets on a person’s body or clothing, it could cause skin injuries or burns. If

this should happen, wash it off with clean water and then consult a doctor

immediately.

• The unit power should be off when you install and replace batteries.

• Remove the batteries if you do not plan to use the unit for a long time.

Batteries could rupture or leak, causing fire, injury or stains around them. If the

TASCAM DR-70D 5

battery fluid leaks, wipe away any fluid on the battery compartment before

inserting new batteries.

• Do not disassemble a battery. The acid inside the battery could harm skin or

clothing.

8For European Customers

Disposal of electrical and electronic equipment

(a) All electrical and electronic equipment should be disposed of separately

from the municipal waste stream via designated collection facilities

appointed by the government or the local authorities.

(b) By disposing of the electrical and electronic equipment correctly, you will

help save valuable resources and prevent any potential negative effects on

human health and the environment.

(c) Improper disposal of waste equipment can have serious effects on the

environment and human health as a result of the presence of hazardous

substances in electrical and electronic equipment.

(d) The crossed out wheeled dust bin

symbol indicates that electrical and electronic equipment must

be collected and disposed of separately from household waste.

(e) The return and collection systems are available to the end users.

For more detailed information about disposal of old electrical

and electronic equipment, please contact your city office, waste

disposal service or the shop where you purchased the equipment.

Disposal of batteries and/or accumulators

(a) Waste batteries and/or accumulators should be disposed of separately from

the municipal waste stream via designated collection facilities appointed by

the government or the local authorities.

(b) By disposing of waste batteries and/or accumulators correctly, you will

help save valuable resources and prevent any potential negative effects on

human health and the environment.

(c) Improper disposal of waste batteries and/or accumulators can have serious

effects on the environment and human health as a result of the presence of

hazardous substances in batteries and/or accumulators.

(d) The crossed out wheeled dust bin

symbol indicates that batteries and/or accumulators must be collected and

disposed of separately from household waste.

If the battery or accumulator contains more than the specified

values of lead (Pb), mercury (Hg), and/or cadmium (Cd) defined

in the Battery Directive (2006/66/EC), then the chemical symbols

for lead (Pb), mercury (Hg) and/or cadmium (Cd) will be indicated

beneath the crossed out wheeled dust bin symbol.

(e) The return and collection systems are available to the end users.

For more detailed information about disposal of waste batteries and/or

accumulators, please contact your city office, waste disposal service or the

shop where you purchased them.

Pb, Hg, Cd

6 TASCAM DR-70D

Contents

Introduction ....................................................................................6

Items included with this product ......................................6

Note about the Reference Manual ...................................7

Precautions for placement and use..................................7

Beware of condensation .........................................................7

Cleaning the unit .........................................................................7

Using the TEAC Global Site ....................................................7

User registration ...........................................................................7

About TASCAM customer support service ..................7

Names of Parts ...............................................................................8

Front panel ..................................................................................8

Rear panel ....................................................................................8

Left side panel ...........................................................................8

Right side panel .......................................................................9

Top panel ......................................................................................9

Bottom Panel .............................................................................9

Home Screen ..................................................................................9

Preparation....................................................................................10

Powering the unit ................................................................ 10

Turning the unit on. ............................................................ 10

Setting the built-in clock .................................................10

Turning the unit off (putting it in standby) .......... 11

Inserting SD cards ................................................................ 11

Camera connection and attachment ...................... 11

Connecting external mics and monitoring

equipment ................................................................................11

Basic operation procedures ................................................12

Menu structure ...................................................................... 12

Recording ......................................................................................12

Recording Screen ................................................................. 12

Menu structure ...................................................................... 13

Setting input destinations .............................................. 13

Adjusting the input level ................................................. 14

Using the limiter ...................................................................14

Setting the low-cut filter ..................................................14

Recording formats ............................................................... 15

Recording (MONO/STEREO/2MIX) ............................15

Playback .......................................................................................... 16

Adjusting the playback volume ..................................16

Playing recordings ............................................................... 16

Selecting files for playback (skipping) ..................... 16

Connecting with a Computer ........................................... 16

Connecting with a computer using USB...............16

Exchanging files with a computer ............................. 16

Disconnecting from a computer ................................ 16

Other settings and information ....................................... 16

System Settings ..................................................................... 16

Quick reference for using various functions ............17

Message ..........................................................................................19

Troubleshooting ........................................................................ 20

Specifications ..............................................................................21

Ratings ........................................................................................21

Inputs and outputs .............................................................21

Audio performance ............................................................21

Recording times (in hours: minutes: seconds) ... 21

Requirements for connected computers..............22

General .......................................................................................22

Introduction

Thank you very much for purchasing the TASCAM

DR-70D.

Before connecting and using this unit, please take

time to read this manual thoroughly to ensure you

understand how to properly set it up and connect

it, as well as the operation of its many useful and

convenient functions.

After you have finished reading this manual, please

keep it in a safe place for future reference. This

Owner's Manual explains the main functions of this

unit. Please see the Reference Manual for information

about all the unit's functions.

This product has a Blackfin® 16/32-bit embedded

processor made by Analog Devices, Inc. This

processor controls the unit's digital signal processing.

Inclusion of this Blackfin® processor in the product

increases its performance and reduces its power

consumption.

Items included with this product

This product includes the following items.

Take care when opening the package to avoid

damaging the items.

Keep the packing materials for transportation in the

future. Please contact the store where you purchased

this unit if any of these items are missing or have been

damaged during transportation.

• Main unit ............................................................................... × 1

• USB cable .............................................................................. × 1

• Camera attachment bracket

screw hole covers ............................................................ × 6

• Owner’s Manual (this document)

including warranty ......................................................... × 1

TASCAM DR-70D 7

Note about the Reference Manual

This Owner’s Manual explains the main functions

of this unit. Please see the Reference Manual for

information about all the unit’s functions.

You can also download this Owner’s Manual and the

Reference Manual from the TEAC Global Site (http://

teac-global.com/).

1. Open the TEAC Global Site (http://teac-global.

com/).

2. In the TASCAM Downloads section, click the

desired language to open the Downloads

website page for that language.

NOTE

If the desired language does not appear, click

Other Languages.

3. Click the product name in the “Search by Model

Name” section to open the Downloads page for

that product.

4. Select and download the Owner’s Manual and

the Reference Manual that are needed.

Precautions for placement

and use

• The environmental temperature operating range

of this unit is 0–40°C (32–104°F).

• Do not install this unit in the following types of

locations. Doing so could degrade the sound

quality and/or cause malfunctions.

Places with significant vibrations

Near windows or other places exposed to

direct sunlight

Near heaters or other extremely hot places

Extremely cold places

Cleaning the unit

Use a dry soft cloth to wipe the unit clean. Do not

wipe with chemical cleaning cloths, thinner, alcohol

or other chemical agents. Doing so could damage

the surface or cause discoloration.

Using the TEAC Global Site

You can download updates for this unit from the

TEAC Global Site:http://teac-global.com/In the

TASCAM Downloads section, select the desired

language to open the Downloads website page for

that language.

User registration

Customers in the USA, please visit the TASCAM

website (https://tascam.com/us/) to register as a user

online.

About TASCAM customer

support service

TASCAM products are supported and warrantied

only in their country/region of purchase.

To receive support after purchase, on the TASCAM

Distributors list page of the TEAC Global Site (http://

teac-global.com/), search for the local company or

representative for the region where you purchased

the product and contact that organization.

When making inquiries, the address (URL) of the

shop or web shop where it was purchased and the

purchase date are required. Moreover, the warranty

card and proof of purchase might also be necessary.

Places with bad ventilation or high humidity

Very dusty locations

Places exposed directly to rain or other water

• Do not place this unit on top of a power amplifier

or other device that generates heat.

• If this unit is placed near a power amplifier or

other device with a large transformer, it could

cause a hum. If this occurs, increase the distance

between this unit and the other device.

• This unit could cause color irregularities on a TV

screen or noise from a radio if used nearby. If this

occurs, use this unit farther away.

• This unit might produce noise if a mobile phone

or other wireless device is used nearby to make

calls or send or receive signals. If this occurs,

increase the distance between this unit and those

devices or turn them off.

• To enable good heat dissipation, do not place

anything on top of this unit.

• Do not place this unit on top of a power amplifier

or other device that generates heat.

Beware of condensation

Condensation could occur if the unit is moved from

a cold place to a warm place, it is used immediately

after a cold room has been heated or it is otherwise

exposed to a sudden temperature change. To

prevent this, or if this occurs, let the unit sit for one

or two hours at the new room temperature before

using it.

8 TASCAM DR-70D

Names of Parts

Front panel

1 Built-in stereo microphone

2 Front cover

3 Battery compartment

4 SD card slot

Rear panel

5 Display

6 DATA dial (ENTER)

Turn to select items and change values on

setting screens.

7 MENU button

8 1/L knob and PEAK indicator

9 2/R knob and PEAK indicator

0 2/7 button

q 1/8 button

w DUAL indicator

This lights when dual recording mode is

selected.

e REC indicator

This lights red when recording.

r Record (0) button

t 3/L knob and PEAK indicator

y 4/R knob and PEAK indicator

u 3// button

i 4/. button

o SLATE button

Use to record slate tones.

Left side panel

NOTE

When connecting and using plugs from

external devices, do not apply excessive force

to the plugs. Doing so could damage the

equipment.

p HOLD/ switch

a 1/L connector (XLR/TRS)

s 2/R connector (XLR/TRS)

d 3/L connector (XLR/TRS)

TASCAM DR-70D 9

Right side panel

NOTE

When connecting and using plugs from

headphones and other external devices,

do not apply excessive force to the plugs.

In particular, be careful not to apply too

much force when using a standard to mini

plug adapter. Doing so could damage the

equipment.

f 4/R connector (XLR/TRS)

g Micro USB port

h EXT IN 1/2 connector (3.5mm stereo mini

jack)

j REMOTE connector (2.5mm TRS jack)

k IN connector (3.5mm stereo mini jack)

l OUT/LINE OUT jack (3.5mm stereo mini

jack)

; PHONES jack (3.5mm stereo mini jack)

z PHONES volume control

Top panel

x DSLR camera attachment bracket

c DSLR mounting screw (1/4-inch)

Bottom Panel

v Tripod mounting threads (1/4-inch)

b Video pin hole

Home Screen

This is the screen that is usually shown during

playback.

CAUTION

When the monitoring function is on, some

meters, icons and other items will change to

recording screen appearance.

1 Recorder operation status

This icon shows the recorder operation status.

Indicator Meaning

8Stopped

9Paused

7Playing back

,Searching forward

mSearching backward

/Skipping to the beginning of the

next track

.Skipping to the beginning of the

previous track

10 TASCAM DR-70D

2 Elapsed time

This shows the elapsed time (hours: minutes:

seconds) of the current file.

3 Monitoring mode

This shows what audio is now being monitored.

Indicator Meaning

MIX Mix of channels 1-4

CAM IN jack sound input

4 Auto tone function status

No icon: Auto tone off

: Auto tone on

5 Power supply status

When a battery is being used, a battery icon

shows the amount of power remaining with 10

levels ( e e ).

The battery is almost dead and the power will

soon turn off (enter standby) if the icon

appears empty and blinks.

When using the PS-P515U AC adapter (sold

separately) or USB bus power, appears.

6 Level meters

These show the levels of the input and playback

signals.

7 Recording status

: Recording off

: Recording on

8 Project name

This shows the name of the project playing

back.

A project is a group of files used for recording/

playback.

9 Remaining time

This shows the elapsed time (hours: minutes:

seconds) of the current file.

0 HOLD/ switch status

: HOLD switch off

: HOLD switch on

q Peak value in decibels (dB)

The maximum level that occurs in a fixed period

of time is displayed in decibels.

Preparation

Powering the unit

8Using AA batteries

1. Open the front cover on the front of the unit.

2. Pull the lever on the battery compartment

cover down to open it.

3. Install 4 AA batteries with their ¥ and ^

marks as shown in the battery compartment .

4. Close the battery compartment cover.

• Use the

BATTERY TYPE

item of the

OTHERS

menu to set the type of battery in order to allow

the unit to accurately show the amount of power

remaining and determine whether enough power

is available for proper operation. (By default, this is

set to “ALKAL” for alkaline batteries.)

Turning the unit on.

To start the unit when off (in standby), slide the

HOLD/ switch toward until

TASCAM

DR-70D

(start-up screen) appears on the display.

The Home Screen appears after the unit starts up.

Setting the built-in clock

When the unit is started up for the first time (or when

the built-in clock is reset after being left unused

without batteries), the

DATE/TIME

screen appears

before the start-up screen to allow the date and time

to be set.

TASCAM DR-70D 11

Turning the unit off (putting it in

standby)

When on, slide the HOLD/ switch toward

until

LINEAR PCM RECORDER

appears on the

display.

The unit turns off (enters standby) after it completes

its shutdown process.

Inserting SD cards

1. Open the front cover on the front of the unit.

2. Insert an SD Card into the slot as shown in the

illustration until it clicks into place.

NOTE

A list of SD cards that have been confirmed

for use with this unit can be found on our

web site.

Please access to a product page of this

product from the TEAC Global Site (http://

teac-global.com) to find the list or contact

the TASCAM customer support service.

Camera connection and

attachment

In order to output the sound from this unit to a DSLR

camera and monitor sound from the camera with

this unit, you must connect them with commercial-

ly-available 3.5mm stereo mini plug cables.

1. If you want to record audio from this unit with a

camera, connect the OUT jack on the right

side of this unit with the external mic input on

the camera.

If you want to input audio from the camera and

monitor it with this unit, connect the IN

jack on the right side of this unit with the audio

output jack on the camera.

DSLR camera

Audio output jack

External mic input jack

NOTE

Refer to the camera’s operation manual to

identify connectors on the camera.

2. Use the

OUTPUT LEVEL

item on the

MONITOR

SETTING

screen to adjust the volume output

to the camera.

3. To mount the camera on this unit, use the

camera attachment screw on the top of the

unit.

Connecting external mics and

monitoring equipment

Connect an external stereo mic to the EXT IN 1/2

jack on the right side of the unit.

To listen with headphones, connect them to the

PHONES jack.

To listen with an external monitoring system

(powered monitor speakers or an amplifier and

speakers), connect it to the OUT/LINE OUT jack.

Headphones

Powered monitor

speakers or amplifier

and speakers

External mic

12 TASCAM DR-70D

Basic operation procedures

1. Press the MENU button to open the

MENU

Screen.

2. Turn the DATA dial to select a menu item

(highlighted), and press the DATA dial to open

various settings screens.

3. Turn the DATA dial to select an item

(highlighted) to be set.

4. Press the DATA dial to move the cursor to

(highlight) the value of the setting.

5. Turn the DATA dial to change the setting.

6. Press the DATA dial to set a different item in the

same menu.

This enables selection of a different item. Turn

the DATA dial to select an item to be set.

7. Repeat step 3 to 6 as necessary to set other

items.

8. Press the MENU button to return to the

MENU

screen (or

OTHERS

screen). Press the 1/8

button to return to the Home Screen.

Menu structure

MENU

BASIC Make recording settings

MONITOR Set monitoring output

INPUT Make input settings

RECORD Make recording format

settings

SLATE Make slate tone settings

MIC Make mic settings

BROWSE Work with files and folders

on the SD card

OTHERS Open the OTHERS submenu

SYSTEM Make system settings for the

unit

BATTERY Set the type of batteries

INFORMATION View information

FILE NAME Make file name settings

DATE/TIME Set the date and time

REMOTE Make remote control settings

Recording

Recording Screen

1 Recorder operation status

This icon shows the recorder operation status.

Indicator Meaning

0Recording

2 Elapsed recording time

The elapsed recording time of the file appears

as hours: minutes: seconds.

3 Monitoring mode

This shows what audio is now being monitored.

Indicator Meaning

MIX Mix of channels 1-4

CAM IN jack sound input

4 Auto tone function status

No icon: Auto tone off

: Auto tone on

5 Level meters

The input signal levels are shown.

TASCAM DR-70D 13

6 Phantom power status

No icon: Phantom power off

: Phantom power on

7 Recording status

: Recording off

: Recording on

8 Project name

This shows the name of the project for the

recorded files.

9 Remaining recording time

The remaining recording time on the SD card is

shown in hours: minutes: seconds according to

the recording mode, sampling frequency and

recording format settings.

0 Low cut filter on/off status

: Low cut filter off

: Low cut filter on

q Limiter function status

: Limiter off

: Limiter on

w HOLD switch status

: HOLD switch off

: HOLD switch on

e Peak value in decibels (dB)

Peak input level values are shown in decibels.

Menu structure

Various settings can be made using the

BASIC

item

of the

MENU

screen.

BASIC

RECORD Recording setting

OFF, ON

PAN Set the left-right balance

(applied to stereo files during

2MIX recording and to

monitoring output)

LEFT 12 − CENTER − RIGHT

12

GAIN Set the input gain

LOW, MID, HIGH, HI+PLUS

INPUT 1/2 Set for the channel 1 and 2

input connectors

EXT_STEREO, EXT_POWER,

XLR/TRS

INPUT 3/4 Set for the channel 3 and 4

input connectors

MIC, XLR/TRS

Setting input destinations

1. Connect external mics to the EXT IN 1/2 or 1/L,

2/R, 3/L and 4/R jacks.

2. Press the MENU button to open the

MENU

Screen.

3. Turn the DATA dial to select

BASIC

, and press

the DATA dial.

The

BASIC

screen opens.

CH1 BASIC screen

4. Turn the DATA dial to select

INPUT 1/2

or

INPUT 3/4

, and press the DATA dial.

5. Turn the DATA dial to select the input desti-

nation.

Options

INPUT 1/2: EXT_STEREO (default), EXT_

POWER, XLR/TRS

INPUT 3/4: MIC (default), XLR/TRS

6. When finished, press the MENU button to

return to the Home Screen.

14 TASCAM DR-70D

Adjusting the input level

1. Press the MENU button to open the

MENU

screen.

2. Turn the DATA dial to select

BASIC

, and press

the DATA dial.

The

BASIC

screen opens.

3. Press the 1/8, 2/7, 3// or 4/. button

to select the channel for input level adjustment.

4. Turn the DATA dial to select the

GAIN

for the

selected channel, and press the DATA dial.

CH1 BASIC screen

5. Turn the DATA dial to set the mic input gain.

Options LOW (default), MID, HIGH, HI+PLUS

6. Repeat step 3 to 5 as necessary to set the mic

input gain for each channel.

7. When finished, press the MENU button to

return to the Home Screen.

8. Use the 1/L, 2/R, 3/L and 4/R knobs on the

front of the unit to adjust the input levels.

The level meters have a b mark as a guide at

−16dB. Set the input levels so that they move

centered around this mark without causing the

1/L, 2/R, 3/L and 4/R knob PEAK indicators to

light red.

Using the limiter

When the limiter is on, the mic input gain will be

adjusted automatically according to the input level

to set the recording level so that distortion does not

occur even when loud sounds are input.

1. Press the MENU button to open the

MENU

screen.

2. Turn the DATA dial to select

INPUT

, and press

the DATA dial.

The

INPUT

screen opens.

3. Press the 1/8, 2/7, 3// or 4/. button

to select a channel to use the limiter on.

4. Turn the DATA dial to select the

LIMITER

for

the selected channel, and press the DATA dial.

Ch1 INPUT screen

5. Turn the DATA dial to set the limiter for mic

input.

Options Meaning

OFF (default

value) Limiter off

MONO Limiter on only for selected

channel

LINK Limiter on for both selected

and linked channels

6. Repeat step 3 to 5 as necessary to set the limiter

for each channel.

7. When finished, press the MENU button to

return to the Home Screen.

Setting the low-cut filter

Use the low-cut filter if you want to cut noise and

other sounds at low frequencies. This function

can be used to reduce air-conditioning noise and

unpleasant wind noise, for example.

1. Press the MENU button to open the

MENU

screen.

2. Turn the DATA dial to select

INPUT

, and press

the DATA dial.

The

INPUT

screen opens.

3. Press the 1/8, 2/7, 3// or 4/. button

to select a channel to use the low-cut filter on.

4. Turn the DATA dial to select the

LOWCUT

for

the selected channel, and press the DATA dial.

Ch1 INPUT screen

5. Turn the DATA dial to select the cut off

frequency of the low cut filter for mic input.

Options: OFF (default value), 40Hz, 80Hz, 120Hz,

180HZ, 220Hz

6. Repeat step 3 to 5 as necessary to set the

low-cut filter for each channel.

7. When finished, press the MENU button to

return to the Home Screen.

TASCAM DR-70D 15

Recording formats

You can select the format of files created by this unit.

8MONO recording

The channels selected for recording will be recorded

as mono files.

A file will be made for each channel selected for

recording.

8STEREO recording

Stereo files will be recorded.

Examples:

If only channel 1 is selected for recording, a stereo

file with channel 2 silent will be created.

If only channels 1 and 3 are selected for recording,

stereo files with channels 2 and 4 silent will be

created.

82MIX recording

The input signals set on the BASIC screen will be

recorded as a stereo file.

Even if all four channels are selected for recording, a

stereo file will be created.

Recording (MONO/

STEREO/2MIX)

8Make recording settings

1. Press the MENU button to open the

MENU

screen.

2. Turn the DATA dial to select

RECORD

, and press

the DATA dial.

The

RECORD SETTING

screen opens.

3. Turn the DATA dial to select

FILE TYPE

, and

press the DATA dial.

4. Turn the DATA dial to select the recording

format.

Options: MONO, STEREO (default), 2MIX

5. Press the DATA dial to enable selection of other

items.

6. When finished, press the MENU button to

return to the Home Screen.

8Setting where to save files

1. Press the MENU button to open the

MENU

screen.

2. Turn the DATA dial to select

BROWSE

, and press

the DATA dial.

The

BROWSE

screen opens.

3. On the

BROWSE

screen, select the folder where

you want to save recorded files, and press the

DATA dial.

This opens the browse menu pop-up.

4. Turn the DATA dial to select

SELECT

, and press

the DATA dial.

5. The Home Screen reopens, and the selected

folder is where recorded files will be saved.

8Starting recording

1. Press the record (0) button to start recording.

When recording starts, the REC indicator

lights and the display shows the project

name, elapsed recording time and remaining

recording time.

2. Press the record (0) or 1/8 button to stop

recording.

3.

16 TASCAM DR-70D

Playback

Adjusting the playback volume

Use the

OUTPUT LEVEL

item on the

MONITOR

SETTING

screen to adjust the volume output from

the OUT/LINE OUT jack.

Use the PHONES volume control to adjust the

volume output from the PHONES jack.

Playing recordings

When the Home Screen is open and playback is

stopped, press the 2/7 button to start playback.

8Pausing playback

When the Home Screen is open and a track is playing

back, press the 1/8 button to pause playback at the

current position.

8Stopping playback

When the Home Screen is open and a track is playing

back, press the 1/8 button to pause playback,

and press the 1/8 button again to return to the

beginning of the file and stop playback.

8Searching backward and forward

When the Home Screen is open and a track is

playing back or stopped, press and hold the 4/.

or 3// button to search forward or backward.

8Changing the playback position

Turn the DATA dial while the Home Screen is open

during playback or when paused or stopped to

change the position where the slate tone will be

inserted.

After changing the playback position, playback will

resume. If playback had been stopped or paused,

though, it will be paused instead.

Selecting files for playback

(skipping)

When the Home Screen is open, use the 4/. and

3// buttons to select a file for playback.

Press the 4/. button when at the beginning of a

file to skip to the beginning of the previous file.

Press the 3// button when at the beginning or

middle of a file to skip to the beginning of the next

file.

Connecting with a Computer

You can transfer audio files on the SD card in the unit

to a computer, as well as transfer audio files from the

computer to the unit.

Connecting with a computer

using USB

1. Use the included USB cable to connect the unit

to a computer. If the unit is off, turn it on.

2. On the

USB SELECT

screen, select

STORAGE

,

and press the DATA dial to connect this unit to

the computer. “USB connected” will appear on

the display.

3. This unit appears on the computer as an

external drive named “DR-70D” (if the card has

been formatted by this unit).

Exchanging files with a

computer

After following the instructions in the previous

section, click the “DR-70D” drive on the computer

screen to show the “MUSIC” and “UTILITY” folders.

To transfer files to the computer, open the “MUSIC”

folder and drag and drop the desired files to destina-

tions of your choice.

To transfer files from the computer, drag and drop

the audio files on the computer that you want to the

"MUSIC" folder.

Disconnecting from a computer

Before disconnecting the USB cable, use the proper

procedures for the computer to unmount this unit.

The unit turns off after it completes its shutdown

process.

See the computer’s operation manual for instruc-

tions about how to unmount an external volume.

Other settings and

information

System Settings

Use the

SYSTEM

menu to make various settings to

use the unit as you like. You can also initialize settings

and format SD cards, for example.

1. Select

MENU

w

OTHERS

w

SYSTEM

, and

press the DATA dial.

2. Make the necessary settings using the various

functions.

TASCAM DR-70D 17

Quick reference for using various functions

• Button names are shown like this: MENU.

• Instructions are abbreviated. For example, “On the Home Screen, press the MENU button. Select the

BASIC

menu, and then select the

RECORD

item” becomes: Home

Screen w MENU w

BASIC

w

RECORD

.

• Not all steps are given for complex operations. For detailed operation procedures, see the Reference Manual.

Category Desired action Function name Procedures, buttons used and explanation

Basic

functions

Return to the Home Screen 1/8

Return to the Home Screen if you become unsure about how to proceed.

Record Record (0)

Recording will start using the current settings.

Play a recording Home Screen w 2/7

Play the file shown (selected).

Adjust the playback volume PHONES volume, MENU w

MONITOR

w

OUTPUT LEVEL

Adjust the volume of headphones, speakers, etc.

Select a file for playback Home Screen w . and /

If there a many files, using the browse function might be more convenient.

Recording

Change the file format Home Screen w MENU w

REC SETTING

w

FORMAT

Set the file format (BWF, WAV, etc.) used for recordings.

Set the low-cut filter Low cut filter Home Screen w MENU w

INPUT SETTING

w

LOW CUT

This function removes noise and other sounds at low frequencies. Set the cutoff frequency.

Set the input gain Home Screen w MENU w

BASIC

w

GAIN

Sets the input gain.

Adjust the input level manually 1/L, 2/R, 3/L, 4/R

Watch the meters and set the recording level so that they do not peak.

Adjust the input level automati-

cally Limiter

Home Screen w MENU w

INPUT SETTING

w

LIMITER

This function compresses only loud sounds to prevent overloads and does not change the

recording level.

Other

recording

features

Create a new file manually while

recording Manual track incrementation

Recording Screen w /

Use this function if you want to create a new file without interrupting recording when, for

example, the song changes.

Add a slate tone When recording w SLATE

You can add slate tones to recorded files at the points you want.

18 TASCAM DR-70D

Category Desired action Function name Procedures, buttons used and explanation

File opera-

tions

Check file information Home Screen w MENU w

BROWSE

w DATA w

INFO

Use this function to check the date of recording and file size, for example.

Delete a file Home Screen w MENU w

BROWSE

w DATA w

DELETE

You can delete files that you do not need.

Delete all files in a folder at the

same time

Home Screen w MENU w

BROWSE

w DATA w

ALL DEL

You can delete all the files in a folder at the same time.

Unit

settings

Set the date and time

Home Screen w MENU w

OTHERS

w

DATE/TIME

Use this function to set the internal clock, which is used for the recording dates written to

files, for example.

Turn plug-in power on

Home Screen w MENU w

BASIC

w

INPUT 1/2 SELECT

w

EXT POWER

Make this setting when using an external mic that requires plug-in power connected to

the EXT IN 1/2 jack.

Check information about the unit

or card

Home Screen w MENU w

OTHERS

w

INFORMATION

Use this function to check the unit firmware version and the amount of remaining space

on the card, for example.

Change the automatic power

saving function Automatic power saving Home Screen w MENU w

OTHERS

w

SYSTEM

w

AUTO PWR SAVE

This function automatically turns the unit off when it is not used for some time.

Change the backlight setting Home Screen w MENU w

OTHERS

w

SYSTEM

w

BACKLIGHT

Use this to change the display backlight setting.

Adjust the display contrast Home Screen w MENU w

OTHERS

w

SYSTEM

w

CONTRAST

Use this to set the contrast of the characters on the display.

Set the battery type

Home Screen w MENU w

OTHERS

w

BATTERY

Select the type of battery being used. This setting affects the accuracy of the remaining

battery display.

Set the phantom power voltage Home Screen w MENU w

MIC

w

PHANTOM VOLT

Sets the phantom power voltage.

Restore the unit to its default

settings Initialize Home Screen w MENU w

OTHERS

w

SYSTEM

w

INITIALIZE

Use this function to restore all settings to their factory defaults.

Format an SD card Format Home Screen w MENU w

OTHERS

w

SYSTEM

w

FORMAT

Use this function to format cards.

Unit

settings Set the file name format Home Screen w MENU w

OTHERS

w

FILE NAME

You can change the characters used in the file names that are automatically assigned.

TASCAM DR-70D 19

Message

The following is a list of the pop-up messages.

Refer to this list if one of these pop-up messages appears on the DR-70D and you

want to check the meaning or determine a proper response.

If the error message continues to appear frequently, please contact the store

where you purchased this unit or a TASCAM customer support service.

Message Meaning and response

Battery Empty The batteries are almost out of power. Replace the

batteries.

Card Error The SD card could not be recognized properly. Change the

card.

Card Full The SD card has no remaining space. Erase unnecessary

files or move them to a computer to make open space.

File Full

The total number of folders and files exceeds the limit of

5000. Erase unnecessary folders and files or move them to

a computer.

File Not Found A file cannot be found or a file might be damaged. Please

check that file.

File Not Found

Make Sys File

The system file is missing. This unit requires a system file

for operation. When this message appears, press the DATA

dial to automatically create a system file.

File Protected The file is read only and cannot be erased.

Format Error

Format CARD

The SD card is not formatted properly or the card is broken.

This message also appears if the card was formatted using

a computer connected by USB or if an unformatted card is

inserted in the unit.

Always use the DR-70D to format cards to be used with it.

Change the card or press the DATA dial while this message

is being shown to format the card.

Formatting will erase all the data on the SD card.

Invalid Card

Change Card

Something might be wrong with the SD card. Change the

SD card.

Message Meaning and response

Invalid SysFile

Make Sys File

The system file required to operate this unit is invalid. When

this message appears, press the DATA dial to automatically

create a new system file.

Layer too Deep Folders can be created down to two layers. You cannot

create a new folder inside the current folder.

MBR Error Init CARD

The SD card is not formatted properly or the card is broken.

Change the card or press the DATA dial while this message

is being shown to format the card.

Formatting will erase all the data on the SD card.

No Card No SD card is loaded in the unit. Insert a recordable SD

card.

No PB File There is no file that can be played back. The file might be

damaged.

Non-Supported

The audio file is not a supported format. Please see

“Connecting with a Computer” in the Reference Manual for

file formats that this unit can use.

Switched To Internal

Battery

The power source has switched from USB bus power to

the batteries in the unit.

Write Timeout

Writing to the SD card timed out.

Backup files on the card to a computer, and format the

card.

Not Possible

Check INPUT3/4

The setting cannot be changed.

Check the INPUT 3/4 setting.

Not Possible

Check Rec Chs.

The setting cannot be changed.

Check the recording channels.

Not Possible

Set DUAL-REC OFF

The setting cannot be changed.

Turn DUAL REC mode off.

No Rec Channels

Selected No recording channels have been selected (all are off).

If any other error occurs, turn the unit off and restart it.

20 TASCAM DR-70D

Troubleshooting

If you are having trouble with the operation of this unit, please try the following

before seeking repair. If these measures do not solve the problem, please contact

the store where you purchased this unit or TASCAM customer support service.

8The unit will not turn on.

• Confirm that the batteries are not dead.

• Confirm that the batteries are installed with the correct ¥/^ orientation.

• Confirm that the AC adapter (TASCAM PS-P515U, sold separately) is securely

connected to both the outlet and the unit.

• When using USB bus power, confirm that the USB cable is securely connected.

• When using USB bus power, confirm that it is not connected via a USB hub.

8The unit turns off automatically.

Is the automatic power saving function on? (See "Setting the automatic power

saving function" in "Settings and Information" of the Reference Manual.)

iSince this unit complies with the European Standby Power Regulations (ErP),

the automatic power saving function operates regardless of whether the unit

is being powered by an AC adapter or batteries. If you do not want to use the

automatic power saving function, set it to "OFF". (The factory default setting is

"30min".)

8The unit does not function.

• Confirm that the HOLD/ switch is not set to HOLD.

• Is the unit connected to a computer by a USB cable? (Does "USB connected"

appear on the display?)

8The SD card is not recognized.

• Confirm that the SD card is inserted completely.

8Playback is not possible.

• If you are trying to play a WAV file, confirm that the sampling frequency is

supported by this unit.

8No sound is output.

• Check the connections with the monitoring system.

• Is the volume of the monitoring system minimized?

• Is the output level setting of the unit minimized?

8Recording is not possible.

• Check connections with other equipment again.

• Check the input settings again.

• Confirm that the input level is not too low.

• Confirm that the SD card is not full.

• Confirm that the number of files has not reached the maximum that the unit

can handle.

8The input level is low.

• Confirm that the input level setting is not too low.

• Confirm that the output level of any connected device is not too low.

8The sound I am trying to record sounds distorted.

• Confirm that the input level setting is not too high.

8Adjust the input knobs so that the PEAK indicators do

not light.

• Lower the volumes of the sound sources being input to this unit.

8I cannot erase a file.

• Confirm that you are not trying to erase a file that has been copied from a

computer after being write-protected.

8This unit’s files do not appear on the computer.

• Confirm that the unit is connected to the computer using its USB port.

• Confirm that no USB hub is being used.

• Confirm that the unit is not recording.

La pagina sta caricando ...

Tascam DR-70D Manuale del proprietario

Tascam DR-70D Manuale del proprietario

in altre lingue

Documenti correlati