Vermeiren LiNX 400 Manuale utente

Tipo
Manuale utente
VERMEIREN
LiNX 400
U S E R M A N U A L
M A N U E L D ' U T I L I S A T I O N
G E B R U I K S A A N W I J Z I N G
G E B R A U C H S A N W E I S U N G
I S T R U Z I O N I
M A N U A L E D I
M A N U A L D E
I N S T R U C C I O N E S
I N S T R U K C J A O B S
Ł
U G I
N Á V O D K O B S L U Z E
Instrukcje dla wyspecjalizowanego
All rights reserved, including translation.
No part of this manual may be reproduced in any form what so
ever (print, photocopy, microfilm or any other process) without
written permission of the publisher, or processed, duplicated or
distributed by using electronic systems.
Tous droits réservés, y compris la traduction.
Aucune partie de ce manuel ne peut être reproduite, sous
quelque forme que ce soit (imprimée, photocopie, microfilm ou
tout autre procédé) sans l'autorisation écrite du publicateur, ni
traitée, dupliquée ou distribuée à l'aide de systèmes
électroniques.
Alle rechten, inclusief vertaling, voorbehouden.
Niets uit deze handleiding mag geheel of gedeeltelijk in enige
vorm (druk, fotokopie, microfilm of ieder ander procedé) zonder
de schriftelijke toelating van de uitgever worden
gereproduceerd of met behulp van elektronische systemen
worden verwerkt, gekopieerd of verspreid.
Alle Rechte, auch an der Übersetzung, vorbehalten.
Kein Teil der Gebrauchsanweisung darf in irgendeiner Form
(Druck, Fotokopie, Mikrofilm oder einem anderen Verfahren)
ohne schriftliche Genehmigung des Herausgebers
reproduziert oder unter Verwendung elektronischer Systeme
verarbeitet, vervielfältigt oder verbreitet werden.
Tutti i diritti riservati (anche sulla traduzione).
Il presente manuale non può essere riprodotto, neppure
parzialmente, con alcun mezzo (stampa, fotocopia, microfilm o
altro procedimento) senza l’autorizzazione scritta della casa
produttrice, elaborato, duplicato o distribuito con l’ausilio di
sistemi elettronici.
Todos los derechos reservados, incluidos los de la
traducción.
Se prohíbe la reproducción total o parcial del presente manual
de cualquier forma (impresión, fotocopia, microfilm o cualquier
otro procedimiento), así como la edición, copia o distribución
empleando sistemas electrónicos, sin el permiso escrito del
editor.
Wszelkie prawa zastrzeżone, łącznie z tłumaczeniem.
Żadna część niniejszej instrukcji nie może być powielana w
jakiejkolwiek formie (drukowanej, fotokopii, mikrofilmu ani
innej) bez pisemnej zgody wydawcy, nie może być również
przetwarzana, kopiowana ani rozprowadzana za pomocą
systemów elektronicznych.
Všechna práva vyhrazena, včetně překladu.
Šíření jakékoliv části tohoto katalogu jakýmkoliv způsobem
(tisk, kopie, mikrofilm nebo jiný způsob) bez písemného
souhlasu vydavatele, nebo zpracování, duplikace či distribuce
prostřednictvím elektronických systémů je zakázáno.
EN
Instructions for specialist dealer
This instruction manual is part and parcel of the
product and must accompany every product
sold.
Version: B, 2021-09
FR
Instructions pour les distributeurs
Ce manuel d'instructions fait partie du produit et
doit accompagner chaque produit vendu.
Version : B, 2021-09
NL
Instructies voor de vakhandelaar
Deze handleiding is deel van het product en
dient bij iedere product te worden geleverd.
Versie: B, 2021-09
DE
Hinweise für den Fachhändler
Diese Gebrauchsanweisung ist Bestand-teil des
Produkts und ist bei jeder Produkts
auszuhändigen.
Version: B, 2021-09
IT
Istruzioni per il rivenditore
Il presente Manuale di istruzioni è parte
integrante del prodotto e deve essere fornito
assieme alla prodotto.
Versione: B, 2021-09
ES
Instrucciones destinadas a los distribuidores
especializados
El presente manual de instrucciones es parte
integrante del producto y se debe adjuntar a
todas las producto que se vendan.
Versión: B, 2021-09
PL
sprzedawcy
Niniejsza instrukcja obsługi jest nieodłączną
częścią produktu i musi być dołączona do
każdego sprzedawanego produktu.
Wersja: B, 2021-09
CS
Pokyny pro specializovaného prodejce
Tento návod k obsluze je součástí dodávky a
musí být součáskaždého prodaného
produktu.
Verze: B, 2021-09
Multi version: B, 2021-09
Language index
English
Français
Nederlands
Deutch
Italiano
Español
Polski
Czech
User manual
Manuel d'utilisation
Gebruiksaanwijzing
Bedienungshandbuch
Manuale di istruzioni
Manual de instrucciones
Instrukcja obsługi
Návod k obsluze
This page is intentionally left blank
LiNX 400
2021-09
Content
1
EN
NL
Content
Content ....................................................................................................................... 1
Preface........................................................................................................................ 2
1 Description .................................................................................................... 3
2 Before use ..................................................................................................... 4
2.1 General safety instructions ............................................................................. 4
3 Driving ........................................................................................................... 5
4 Operating console functions ....................................................................... 6
4.1 Switching ON / OFF ........................................................................................ 6
4.2 Failures and blocks ......................................................................................... 7
4.3 Battery status and charging ............................................................................ 7
4.4 Navigation ....................................................................................................... 8
4.5 Settings button ................................................................................................ 8
4.6 Joystick operation (driving and braking) ........................................................ 11
4.7 Operating console lock ................................................................................. 12
4.8 Adjusting your body position ......................................................................... 12
4.9 Changing drive function ................................................................................ 13
4.10 Horn .............................................................................................................. 14
4.11 Lighting ......................................................................................................... 14
5 Troubleshooting .......................................................................................... 15
LiNX 400
2021-09
Preface
2
EN
NL
Preface
Important note
This manual reflects the latest product developments. Vermeiren has the right to implement
changes to this type of product without being imposed to any obligation to adapt or replace similar
products previously delivered.
Pictures are used to clarify the instructions in this manual. Details of the depicted product may
deviate from your product.
Information available
On our website http://www.vermeiren.com/ you will always find the most recent version of the
information in this manual. Please consult this website regularly for possible updates.
Visually impaired people can download the electronic version of this manual and have it read out
by means of a text-to-speech software application.
This user manual of applied operating console
For user and specialist dealer
User manual of wheelchair
For user and specialist dealer
Installation manual of wheelchair
For specialist dealer
User manual of battery and charger
For user and specialist dealer
LiNX 400
2021-09
Description
3
EN
NL
1 Description
The operating console built into your electric wheelchair enables you to control all the driving,
steering, braking and operating processes, as well as other adjusting motors (lifting column, seat
and back adjuster). The wheelchair's electrical unit and electronics are constantly being monitored
internally.
The following pictures show all parts that are relevant to the user.
Important parts
1
3
4
5
2
9
7
8
6
LiNX 400
2021-09
Before use
4
EN
NL
2 Before use
Risk of injuries and damage
Do NOT install, maintain or use this product unless you have read and fully understood all
instructions in this manual and all relevant manuals regarding the wheelchair equipped with
this product.
Do not try to open or disassemble the console in any case - there are no user-serviceable parts
inside.
In case of doubts or questions, do not hesitate to contact your local specialist dealer, your care
provider, or your technical adviser to help you with this.
2.1 General safety instructions
Keep the following general warnings in mind during use:
The operating consoles have been tested for electromagnetic compatibility on typical,
representative vehicles and comply with the appropriate EMC standards:
EN 12184: 2014, ISO7176-21: 2009.
Nevertheless, sources of electromagnetic field may influence the driving performance of your
wheelchair, like the fields of mobile phones, power generators or high-power energy sources.
On the other hand, the electronics of your wheelchair can affect other electronic appliances
too, like alarm systems of shops and automatic doors. We therefore advise you to check your
operating console / wheelchair regularly for damage and wear, since these may enlarge the
interference.
Be aware that the surface of the operating console may get very hot due to solar radiation or
heating devices. Be careful when touching.
Make sure that the controller does not become colder or hotter than the allowed minimum
and maximum temperature, see the wheelchair user manual.
Before switching the wheelchair on, be aware of your environment/situation. Adjust your
speed accordingly before driving off. We advise you to use the slowest speed setting to drive
indoors. For outdoor driving you can adjust the speed to a suitable speed at which you feel
comfortable and safe.
Do not touch the connector pins. If you touch the pins, they can become dirty, or they can be
damaged by electrostatic discharge.
If the wheelchair has not been fitted with a hand guard for the operating console, be aware
that your hand will not be protected from crushing, for example while manoeuvring towards a
table.
The XLR connector on the controller is to be used exclusively for the intended purpose of
charging the battery. The warranty will lapse if any unauthorized device is connected to this
port.
Make sure that the battery charger that is used with the vehicle has a drive-inhibited function
that is correctly connected for use with the controller. This drive-inhibited feature is intended
to prevent the chair from driving while the battery is being charged. If you are not sure, ask
your dealer.
Immediately turn the controller off and consult your service agent if the vehicle:
o is damaged;
o does not behave the same every time;
o does not respond normally, the way you expect it to;
WARNING
Vermeiren is responsible for software updates/repairs. For adaptations in the software,
contact Vermeiren, see our website http://www.vermeiren.com/
LiNX 400
2021-09
Driving
5
EN
NL
o becomes hotter than normal;
o smokes;
o does not change its speed when you adjust the speed dial;
o displays a fault on its fault indicator and the controller does not perform normally.
Turn the controller off:
o when you do not use it;
o before you get in or out of the wheelchair;
o if your vehicle drives by itself or against your will. When you turn the controller off, the
vehicle will halt.
3 Driving
1. Press the ON/OFF button.
2. If the LED on the ON/OFF button is green, the wheelchair is powered and ready to go.
3. Check the battery status indicator. Charge the battery if necessary (see § 4.3).
4. Select the driving program and set the speed range by sliding the arrow (S), see driving
functions in § 4.9.
5. Start moving the wheelchair by operating the joystick slowly forwards/backwards.
6. The speed will increase when you push the joystick further out of the centre.
7. To turn left or right, push the joystick to the left or right. Use your direction indicators when
driving outdoors, see § 4.11.
8. To brake, move the joystick to neutral position.
9. After arrival, check the battery status and press the ON/OFF button.
10. Charge the battery if necessary.
LiNX 400
2021-09
Operating console functions
6
EN
NL
4 Operating console functions
The operating console enables you to control all driving components as well as the motors to
adjust your body position. For your own safety, and to prevent that the wheelchair gets damaged,
movements are monitored by the electronics. This may result in block of movement, speed
decrease or complete stop.
4.1 Switching ON / OFF
Put the joystick in the neutral (central) position before pressing the ON/OFF button.
If the console is switched on with the joystick out of the neutral position, the wheelchair will
not drive. Release the joystick (return to neutral) within 5 seconds to unlock the drive. If the
joystick is not released within 5 seconds, the fault turns into a Module fault which is
indicated by the red blinking LED in the ON/OFF button. The wheelchair will not drive. To
clear the Module fault, release the joystick and switch the operating console OFF and then
ON again.
To switch the operating console ON, press the ON/OFF button once.
The start screen is displayed for a few seconds, after which the
operating screen appears. The LED (status indicator) in the ON/OFF
button goes on. When it turns green, the operating console is ready
for operation. When the LED starts blinking in red, there is a failure,
see §4.2 and §5.
To switch the operating console OFF when it is ON: press the button
once.
The operating console will power down and the status indicator goes
out.
Switching ON/OFF
4.1.1 Emergency stop
If you need to stop a driving or body-positioning movement quickly, press the ON/OFF button to
perform an EMERGENCY STOP. The wheelchair will come to a halt quickly.
4.1.2 Sleep mode
The operating console will go into sleep mode after a period of inactivity (default 5 minutes).
When the system sleeps, it is partially turned off to reduce energy consumption.
To reactivate the operating console, press a button or move the joystick.
LiNX 400
2021-09
Operating console functions
7
EN
NL
4.2 Failures and blocks
When the operating console is powered and a failure
appears, the indicator of the ON/OFF button starts blinking
in red, see picture. The number of blinks indicates the fault
code. For a few seconds, a triangle with fault code (A) is
displayed. The ON/OFF button will keep blinking.
In case of a failure, one or all functions of the operating
console are blocked. This is indicated by the “forbidden”-
symbol and the yellow warning bars (B).
Failure indication and drive inhibited
The status is indicated by a small symbol (C) in the top corner of each screen.
For more information, see §5.
4.3 Battery status and charging
Risk of injuries and damage
Follow the charging instructions in the wheelchair instruction manual and the suppliers’ manual
of the battery charger.
The battery charge indicator (located at the top of the touchscreen) provides
an estimation of the remaining battery capacity.
In the following table all battery indications and their meanings are collected.
Battery status indication
Table 1: Battery status description
Display
Description
Meaning
Remarks
Most blocks are green
Battery capacity: more
than 50% of full
capacity.
Blocks turn yellow
Battery capacity level
is decreasing: less
than 50% of full
capacity
Consider recharging
the battery soon.
Blocks turn red
Battery almost empty
Stop and recharge
now.
Yellow or green blocks
with charging symbol
Battery is charging.
Battery capacity level is
indicated by colour.
Wait until battery is
completely charged.
WARNING
A
B
C
LiNX 400
2021-09
Operating console functions
8
EN
NL
4.3.1 Charging
Driving is prevented (inhibited) while the system is being charged.
Charging is possible without switching the operating console ON. To see the battery
status indicator, switch it ON.
Plug the battery charger into the remote's XLR socket (9), see Figure 1.
The battery status indication now turns into a charge indication, see figure
5. The battery charging state is shown by the yellow or green blocks.
After a few seconds, the operating console turns to power-save mode and
the screen illumination decreases. Tapping on the screen turns normal
illumination on.
Battery-charging indication
4.4 Navigation
There are 2 main menus to view on the touchscreen:
S-menu for adjusting the body position, see §4.8.
D-menu for changing the drive functions, see §4.9.
Each main menu has separate submenus.
Once the operating console has been switched ON, you can navigate through the screens/menu
in two ways:
1. by pressing navigations buttons (see Figure 1, 2+3).
o Press navigation button I (2) shortly, to select a main menu (S, D…)
o Press navigation button II (3) shortly, to select a submenu (S1, S2…)
2. by swiping with your finger on the touch screen
o Swipe up/down to select a main menu (S, D…) and tap to view it.
o Swipe left/right to select a submenu (S1, S2…) and tap to view it.
Use the set key to get an overview on the navigation structure.
4.5 Settings button
The settings button (K) is displayed in each menu screen. With this button, the screen view can
be changed, a popup screen can be opened, and settings can be changed.
To toggle between full screen view and menu-scroll view, tap the settings button shortly.
To open the pop-up screen, hold your finger on the settings button for 4 seconds.
This pop-up screen can also be opened/closed by pressing menu button I (2) for 4 seconds.
LiNX 400
2021-09
Operating console functions
9
EN
NL
Settings button and pop-up screen
To navigate to one of the items in the pop-up screen, tap on the item.
To navigate to the previous screen, tap the return arrow.
To close the pop-up screen, tap on the cross key (M) at the bottom of the screen.
When a selection key is active, the indicator of the key turns green.
4.5.1 Time setting
Tap on the time indication (H in previous figure) and set hour and
minutes by tapping the arrows (I).
To switch from 12-hour dial to 24-hour dial, tap in the area of the
12/24-hour button (J).
Time setting
4.5.2 Screen lock
The Screen lock key (L) (see Figure 6) is primarily intended to restrict the authorisation of the
screen operation to the occupant, but also prevents unintentional use of screen controls.
The screen lock does not influence the driving functions or body-positioning functions. When
the screen is locked, the maximum drive speed is set according to submenu D1.This pop-
up screen can also be opened/closed by pressing submenu button II (3) for 2 seconds.
To lock the screen:
o Tap and hold your finger on the settings button (K) for 7 seconds (see Figure 6).
o To switch the lock ON, tap the selection key of the “screen lock” section. The indicator
turns green.
When the screen is locked, all operating keys are greyed out and become inoperable.
The symbol of the settings button (K) turns into a padlock.
To unlock the screen:
o Switch off the operating console with the ON/OFF button to lift
the lock.
The keys on the screen become operable again.
Screen locked
D1
2
K
M
H
L
I
J
D1
K
LiNX 400
2021-09
Operating console functions
10
EN
NL
4.5.3 Glove mode
The touchscreen is programmed to a particular degree of touch sensitivity.
For this reason, the screen does not respond when you wear gloves. With
this function, you can increase the touch sensitivity so you can operate the
console while wearing gloves.
To switch the glove mode ON, tap the selection key (G). The indicator
turns green.
To switch this mode off, tap the selection key again. It is now greyed
out. Glove mode key
4.5.4 Settings
Tap on your chosen setting to enter the setting menu and submenus.
Settings menu
Display
1. Brightness
o Move the green slider to the left/right to decrease/increase the brightness of the screen.
2. Language
o Your operating console is set to English by default. your preferred language can be
selected from the list under the “Language” setting.
Interaction
1. Tap only mode
o Tap this selection key to switch this mode OFF or ON. After switching on this function,
sliding and wiping do not operate. The screen can only be operated by tapping the
arrow keys and +/- keys that replace these functions.
2. Tap zone
o Move the slider to the left/right to decrease/increase the sensitivity zone of the tap field.
3. Left hand mode
o Tap this selection key to switch this mode OFF or ON. By switching on, the location of
the operating keys switches from the right to the left side of the screen.
G
LiNX 400
2021-09
Operating console functions
11
EN
NL
4.5.5 Odometer
The menu screen shows the speed indication as well as an indication of the travelled trip distance
(N).
To reset the trip distance back to zero:
Enter the setting menu by tapping the settings button (K).
Tap on the submenu “Odometer”.
To reset the trip distance (P) to zero, tap the button (R).
The total traveled distance (O) cannot be reset.
To switch between distance indication in kilometers or miles, tap (Q).
Joystick movements
4.6 Joystick operation (driving and braking)
Operating the joystick in a specific direction will move the electric wheelchair
in that direction. The speed of movement depends on the displacement of the
joystick. If the joystick is pushed/pulled to maximum displacement, the speed
will be maximal (within the selected drive mode).
By moving the joystick to its central position (neutral) during driving, the
brakes will start working until the wheelchair stops:
For gradual braking, move the joystick slowly
For a quick stop, release the joystick; the wheelchair will stop as
quickly as possible. Joystick movements
Make sure that the joystick is in neutral (central) position when pressing the on/off button,
otherwise the electronics will be locked.
After switching the operating console ON by the ON/OFF button, the joystick stays in the
central position for at least five seconds. The console has been programmed this way for
technical and safety reasons. If joystick and ON/OFF button are activated at the same time,
the steering unit is locked and will only unlock after switching completely OFF.
Make sure that the free-wheel lever is in braking position BEFORE switching the wheelchair
ON. Electromagnetic brakes do NOT function if the wheelchair is in free-wheel mode. This
is indicated on the operating console. Driving is not possible.
To prevent unintended changes of the settings, the operating keys disappear during
operation of the joystick. As soon as the joystick is in neutral position, the keys appear again.
N
O
P
Q
R
LiNX 400
2021-09
Operating console functions
12
EN
NL
4.7 Operating console lock
It is also possible to lock the operating console, to prevent unauthorized use of the wheelchair.
To lock the console: Press the ON/OFF button until the lock symbol appears and the screen
goes black.
To unlock the console: hold your finger on the screen. The lock symbol appears again,
together with a white loading bar around the screen. Wait until the bar is fully loaded, the
console now becomes operable again.
4.8 Adjusting your body position
Risk of injuries or damage
Be aware that the stability decreases when the wheelchair is moved from sitting straight to
inclined position.
Make sure there is enough space around the wheelchair to operate the backrest and seat.
The wheelchair's adjusting functions can be operated from the S-menu. Depending on your type
of wheelchair, there can be up to 6 submenus.
To adjust your body position, move the joystick to the front or back, according to the arrows
on the screen.
To return to the basic sitting position, move the joystick to the back for each adjusting
movement.
Seat height (lift)
Backrest inclination
Seat & backrest inclination
Left foot support
Right foot support
Both foot supports/central
footplate
Possible submenus
CAUTION
LiNX 400
2021-09
Operating console functions
13
EN
NL
4.9 Changing drive function
The wheelchair's speed functions can be operated from the D1, D2, or D3 submenu. These
submenus allow the user to select the maximum speed limit of the wheelchair (that is the speed
when the joystick is fully deflected) to their preference and environment.
The maximum driving speed by maximal deflection of the joystick depends on the selected drive
submenu (D1, D2 or D3) and the manual speed setting in this submenu.
Low speed setting
(indoor driving)
Medium speed setting
(indoor-outdoor driving)
High speed setting
(outdoor driving)
Submenu D1, D2, D3
In each drive submenu, the speed can be changed in 10 discrete steps between lowest and
highest speed. The available speed range for joystick operation is displayed in green. The yellow
part is the remaining speed range, not in use.
The speed range can be changed by sliding the arrow key (S):
UP, to increase speed range (more green)
DOWN, to decrease speed range (more yellow)
Low speed range
Medium speed range
Full speed range
Adjusting speed range
S
D1
D1
D1
T
LiNX 400
2021-09
Operating console functions
14
EN
NL
4.9.1 Limited driving speed
For your safety, the driving speed of your wheelchair will be automatically reduced when certain
body position alterations have been made. The drive of the wheelchair is then limited to the lowest
speed setting D1, or even becomes completely blocked.
Driving and speed limitations occur when:
the lift has been adjusted to a higher position. Only speed setting D1 is available.
the backrest inclination exceeds a certain angle
(see figure 15):
1. All functions of your wheelchair are available.
2. Only speed setting D1 is available.
3. Driving your wheelchair is no longer possible.
Raise the backrest until the block is lifted.
Backrest inclination
To lift the speed/driving limitations, lower the lift to
standard (lowest) position, and adjust your seat and backrest to upright sitting position.
4.10 Horn
Press the horn key (T) to warn bystanders, see figure 14. The horn will sound as long as the
button is pressed.
4.11 Lighting
To operate the lights:
1. Go to submenu D1, D2 or D3.
2. Tap key (U) to open the pop-up screen.
3. Tap one of the keys once to switch the light ON,
tap again to switch the light OFF:
o key (V), left indicator
o key (Y), right indicator
o key (W), hazard warning lights
o key (Z), front and back lights
Operation of the lights
When the key is activated, the light symbol is coloured, and a light symbol is shown on the speed
indication circle.
To close the pop-up screen, tap the cross key (X).
After operating keys (V) or (Y), the direction light blinks 8 times before it stops.
The hazard warning lights and main lights must be turned OFF manually by tapping key
(W) and/or (Z) again.
When the hazard warning lights are on, they stay on, even when the operating console
is switched off by the ON/OFF button.
The main lights go out when the operating console is switched off.
U
V
X
Y
W
Z
D1
1
2
3
LiNX 400
2021-09
Troubleshooting
15
EN
NL
5 Troubleshooting
Risk of injuries and damage to the operating console or wheelchair
NEVER attempt to repair the operating console yourself.
For failures of the operating console, you need to contact your specialist dealer.
He/She decides if the console needs to be reprogrammed.
In case of failure, a fault code is displayed by the blinking LED in the ON-OFF button or by a
triangle on the touch screen, see Figure 3.
The following table summarises the possible fault codes. Some problems can be solved by
yourself. For all problems marked in grey, consult your specialist dealer.
Table 2: Troubleshooting
Code
Problem
Meaning
1
Remote / joystick error
Verify that the joystick is in the neutral position when switching
ON the operating console.
Check the joystick: not damaged and working properly.
2
Network or configuration
error
1. Check all connection points and cables.
2. Verify the correct working of the software.
If you cannot find any fault, contact your specialist dealer.
3
Left motor
(or its connection)
is defective.
1. Verify whether the plugs of both motors have been inserted
properly.
2. Check the plug contacts of both motors for corrosion or
damage.
This fault also appears when the motors are disconnected.
Connect again and restart the system.
4
Right motor
(or its connection) is
defective.
As described above.
5
Left parking brake
(or its connection)
is defective or neutral
active.
1. Verify whether the motors' plugs have been inserted properly.
2. Check the plugs for corrosion or damage.
6
Right parking brake
(or its connection)
Is defective.
As described above.
7
Module error
(other than Remote)
One of the wheelchair parts may be damaged except the operator
control.
WARNING
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132

Vermeiren LiNX 400 Manuale utente

Tipo
Manuale utente