Philips 42PF9945/12 Manuale utente

tv

cover 2260.2 30-09-2003 15:08 Pagina 1

Information for users in the UK

(Not applicable outside the UK)

Positioning the TV

For the best results, choose a position where light does not fall directly on the screen, and at some

distance away from radiators or other sources of heat. Leave a space of at least 5 cm all around

the TV for ventilation, making sure that curtains, cupboards etc. cannot obstruct the air flow

through the ventilation apertures.

The TV is intended for use in a domestic environment only and should never be operated or

stored in excessively hot or humid atmospheres.

General Points

Please take note of the section 'Tips' at the end of this booklet.

Interference

The Department of Trade and Industry operates a Radio Interference Investigation Service to help

TV license holders improve reception of BBC and IBA programmes where they are being spoilt by

interference.

If your dealer cannot help, ask at a main Post Office for the booklet "How to improve Television

and Radio Reception".

Mains connection

Before connecting the TV to the mains, check that the mains supply voltage corresponds to the

voltage printed on the type plate on the rear panel of the TV. If the mains voltage is different, con-

sult your dealer.

Important

This apparatus is fitted with an approved moulded 13 Amp plug.

To change a fuse in this type of plug proceed as follows :

1. Remove fuse cover and fuse.

2. Fit new fuse which should be a BS1362 5A,A.S.T.A. or BSI approved type.

3. Refit the fuse cover.

In order to maintain conformity to the EMC directive, the mains plug on this product must not be

removed.

Connecting the aerial

The aerial should be connected to the socket marked x at the back of the set. An inferior aerial is

likely to result in a poor, perhaps unstable picture with ghost images and lack of contrast. Make-

shift or set-top aerials are unlikely to give adequate results.

Your dealer will know from experience the most suitable type for your locality.

Should you wish to use the set in conjunction with other equipment, which connects to the aerial

socket such as TV games, or a video camera, it is recommended that you consult your dealer on

the best method of connection.

Stand (if provided)

Use only the stand provided with the set, making sure that the fixings are properly tightened.A dia-

gram showing how to assemble the stand is packed with the stand. Never use a make-shift stand, or

legs fixed with woodscrews.

cover 2260.2 30-09-2003 15:08 Pagina 2

1

Contents

Preparation ...................................................................................... 2

Keys on top of the TV ................................................................... 2

Your remote control .................................................................. 3-4

To use the menus ........................................................................... 5

Select the menu language and country ..................................... 5

Store TV channels .......................................................................... 6

Automatic installation ............................................................6

Manual installation................................................................... 6

Give name ................................................................................. 7

Reshuffle the programme list................................................. 7

Select favourite TV channels ................................................. 7

TV setup menu ............................................................................... 7

General ...................................................................................... 8

Source ........................................................................................ 9

Decoder .................................................................................... 9

Demo ............................................................................................... 9

Installation

TV menu

Picture menu .................................................................... 10-11

Sound menu ........................................................................... 11

Features menu ................................................................. 11-12

NEXTVIEW/Teletext guide ...................................................... 13-14

Teletext ..................................................................................... 15-16

Connect peripheral equipment

Connecting and selecting equipment ............................... 17-20

Audio and Video equipment keys ............................................. 21

Record with your recorder with Easy Link ........................... 21

Tips .......................................................................................... 22-23

Operation

EasyLink features are based on the “one touch operation” approach.This

means that a sequence of actions are executed at the same time in both the

television and the video cassette recorder, provided both are fitted with the

EasyLink function and connected with the eurocable supplied with your video

recorder.

R End of life directives

Philips is paying a lot of attention to

producing environmentally-friendly in

green focal areas.Your new TV contains

materials which can be recycled and

reused. At the end of its life specialised

companies can dismantle the

discarded TV to concentrate the

reusable materials and to minimise

the amount of materials to be

disposed of.

Please ensure you dispose of your old

TV according to local regulations.

Help?

If this instruction manual does

not give an answer or if ‘Tips’ do

not solve your TV problem, you

can call your Local Philips

Customer or Service Centre. See

the supplied World-wide

guarantee booklet.

Please, have the Model and

Product number which you can

find at the back of your

television set or on the

packaging, ready, before calling

the Philips helpline.

Model: 42PF9945

Product No: ...........................................

Care of the screen

See Tips, p. 22.

EnglishDeutschFrançaisNederlandsItaliano

∂ÏÏËÓÈÎ¿

2260.2 en 30-09-2003 14:58 Pagina 1

1m

min.

2

Preparation

& Wall mounting instructions

For the wall mounting instructions follow the

separate template.

Make sure that the wall mount is being fixed

securely enough so that it meets safety

standards.The weight of the TV (excl.

packaging) is about 40 kg.

Note: not supplied stands are optional accessories.

Consult your dealer.

é Place or hang the TV wherever you want, but

make sure that air can circulate freely through

the ventilation slots. Do not install the TV in a

confined space such as a book case or a

simular unit.

To prevent any unsafe situations, no naked

flame sources, such as lighted candles, should

be placed on or in the vicinity. Avoid heat,

direct sunlight and exposure to rain or water.

The equipment shall not be exposed to

dripping or splashing and no objects filled with

liquids, such as vases, shall be placed on it.

“ Insert the aerial plug firmly into the aerial

socket x at the bottom of the TV. For best

picture quality use the suppressor-aerial cable

supplied.

‘ To connect your computer, see p. 20.

To connect other peripherals, see p. 17.

If you dispose of a Cinema Link combination

(Cinema Link Audio receiver and/or Cinema

Link video recorder and/or DVD player), see

the separate supplied instruction manual.

In order to obtain the best result, please use

only the supplied antenna cables between the

TV and videorecorder, and between

videorecorder and antenna connector.

( Insert the mains cord supplied into the mains

at the bottom of the TV and in the wall socket

having a mains voltage of 220-240V.

To prevent damaging the power (AC) cord

which could cause a fire or electric shock, do

not place the TV on the cord.

§ Remote control: Insert the 2 batteries

supplied (Type R6-1,5V).

The batteries supplied do not contain the heavy

metals mercury and cadmium. Please check on how

to dispose of exhausted batteries according to local

regulations.

è Switch the TV on :Press the power switch B

at the right side of the TV.

An indicator on the front of the TV lights up

and the screen comes on. If the TV is in

standby mode, press the

-P+ keys or the B

key on the remote control.

Keys on top of the TV

Should your remote be lost or broken you can still

change some of the basic settings with the keys on top

of your TV.

Press:

• the V

- or + key to adjust the volume;

• the

-P/CH+ keys to select the TV channels or sources.

The

MENU/OK key can be used to summon the main

menu without the remote control.

Use:

• the V - and + keys and the

P/CH- and P/CH+ keys

to select menu items in the directions as shown;

• the

MENU/OK key to confirm your selection.

Note:

When activated via the

MENU/OK key on top of the TV,

only

Exit lets you dismiss the menu.

Navigate to

Exit and press the MENU/OK key.

MENU/OK - V + - P/CH +

TV

Setup

Demo

Install

Exit

Picture Sound Features

2260.2 en 30-09-2003 14:58 Pagina 2

33

213

546

879

0

B

v

®

Ò

‡π

†

æ b

Ï

i

VCR DVD AMP

¬V PP

0

PIXEL

PLUS

OK

MENU

U

Q

Ì

hb

S

q

SAT

i

®Ò‡π†

Audio- and Video equipment keys

(p. 21)

® Record

See Record with your recorder

with EasyLink, p. 21

U Time display

The time is displayed on the

screen.

æ NEXTVIEW on/off p. 13

OK Press this key

• to activate your choice, when in the

menus.

• to display the programme list.

V To adjust the volume.

¬ Interrupt the sound or restore

it.

i On Screen information

Press to display (when available)

information about the selected

TV channel and programme.

Menu/Remote control info

When a menu is on screen, press

i to display info on the

selected menu item. For

information on the remote

control functions, while the

menu info is displayed, press any

key on the remote control.

The normal function of the key is

not executed.

vSelect peripherals (p. 18)

VCR DVD AMP SAT

Audio- and Video equipment keys

(p. 21)

QSurround mode

Incredible surround

With stereo transmission, and

when Incredible surround is

selected, it seems as though the

loudspeakers are spread further

apart from one another.

Virtual Dolby surround

Optimal with Dolby surround

signals. Enables you to experience

the effect of Dolby surround Pro

Logic, reproducing a rear sound

effect. See Sound menu, 3D effect,

p. 11.

Note:You can make the same

selection in the Sound menu,

surround mode, p. 11.

ÌCinema Go

See separate Cinema Link booklet

supplied.

PIXEL PLUS no function

bTeletext on/off p. 15

ÏMain menu see p. 5

PProgramme selection

To browse through the TV

channels and sources stored in

the favourite list.

0/9 Digit keys

To select a TV channel.

For a two digit programme

number, enter the second digit

within 2 seconds.To switch

immediately to a selected one

digit TV channel, keep the digit key

pressed a bit longer.

Use of the remote control RC2080

Note: For most keys pressing a key once will activate the function. Pressing a second time will de-activate it.

When a key enables multiple options, a small list will be shown. Press repeatedly to select the next item in the list.

The list will be removed automatically after 4 seconds or press

OK to remove immediately.

Remark: in VGA mode only some keys are valid.

B Standby

Press to switch the TV on or off.

When switched off, a red indicator on

the TV lights up.When acquiring

NEXTVIEW

, see p. 14, an orange

indicator lights up and after a period

of max. 1 hour the TV is switched to

full standby and the red indicator

lights up.

2260.2 en 30-09-2003 14:58 Pagina 3

4

213

546

879

0

B

v

®

Ò

‡π

†

æ b

Ï

i

VCR DVD AMP

¬V

P

0

PIXEL

PLUS

OK

MENU

U

Q

Ì

hb

S

q

SAT

0 Previous TV channel

Press to display the previously selected TV channel.

b no function

h Active control see p. 11

qPicture format

Press this key repeatedly or press the cursor up/down to select another

picture format:Auto format, Super zoom, 4:3, Movie Expand 14:9, Movie

Expand 16:9, Subtitle zoom or Wide screen.

Auto format makes the picture fill the screen as much as possible.

In case of subtitles in the bottom black bar, Auto format makes the

subtitles visible. If subtitles are only partly visible, press cursor up.

In case of a broadcaster logo in the corner of the top black bar, the logo

disappears from the screen.

Super zoom removes the black bars on the sides of 4:3 programs with

minimal distortion.

When in Movie Expand 14:9, 16:9, Super zoom or Subtitle zoom picture

format, you can make subtitles visible with the cursor up/down.

Note: With signals via the VGA IN connector less picture formats are

selectable.

S Freeze

To freeze the picture.

Dependent on the input signal, the function may not be possible.

Auto format Super zoom 4:3 Movie Expand 14:9

Movie Expand 16:9 Subtitle zoom Wide screen

2260.2 en 30-09-2003 14:58 Pagina 4

5

To use the menus

& Press the MENU Ï key on the remote control to summon

the main menu.At any moment you can exit the menu by

pressing the

MENU Ï key again.

Note: If you have connected equipment with Cinema Link, more

menu items are present.

é Use the cursor in the up/down direction to select the TV,

Setup, Demo or Install menu.

Use the cursor left/right to select Picture, Sound or

Features.

Note: Sometimes not all the menu items are visible on the screen

(indicated by a cluster of blue balls). Use the cursor down or right

to reveal all items.

“ Use the cursor in the left/right direction to select the menu

item.

‘ Use the cursor up/down again to select the control you

want to select or to adjust.

Note: Items temporary not available or not relevant are displayed

in a light grey colour and cannot be selected.

213

B

v

®

Ò

‡π

†

æ b

Ï

VCR DVD AMP SAT

¬V

PIXEL

PLUS

OK

MENU

U

Q

Ì

PP

cursor to select

adjustments

OK key to

activate

return or switch

main menu on/off

TV

Setup

Demo

Install

Picture Sound Features

Press the i key to get

information about the selected

menu item.

Installation

& Press the MENU Ï key on the remote control.

é Use the cursor down to select Install.

“ Use the cursor right to select Language.

Follow the instructions on screen.

‘ Use the cursor up/down to select your preferred language

and press the

OK key to confirm your selection.

( Use the cursor right to select Country.

§ Select the country where you are now located and press the

OK key.

Select

Other when none of the countries applies.

è Proceed with the Install menu.

Install

Language Country Automatic Manual Give name Reshuffle Favourite

install install programmes

The installation menu contains the following items:

EasyLink

If your video recorder has an EasyLink function, during installation, the language, country and available channels are

automatically transmitted to the video recorder.

Language

English

Deutsch

Français

Install

Country

Austria

Belgium

Croatia

Install

Select the menu language and country

2260.2 en 30-09-2003 14:58 Pagina 5

6

& Select Automatic install in the Install menu.

Note: All channels must be unlocked in order to autoprogram. If

requested, enter your code to unlock all channels. (See TV, Features

menu, Childlock, p. 12.)

é Press the cursor down.

The autoprogramming option label

Start appears.

“ Press the cursor right.

‘ The message Searching appears and the progress of

autoprogramming is displayed.

If a cable system or a TV channel which broadcasts ACI

(Automatic Channel Installation) is detected, a programme list

appears.Without ACI broadcast, the channels are numbered

according your language and country selection.You can use

Reshuffle to renumber them. See p. 7.

It is possible that the cable company or the TV channel displays a

broadcast selection menu. Layout and items are defined by the cable

company or the TV channel. Make your choice with the cursor and

press the

OK key.

After language and country are set correctly, you can now search for and store the TV channels in two

different ways: using Automatic Installation or Manual Installation (tuning-in channel by channel).

Select your choice with the cursor right.

Automatic install

Install Start

Install

Manual installation

Automatic installation

Searching for and storing TV channels is done channel by

channel.You must go through every step of the Manual

Installation menu.

& Select Manual install in the Install menu.

Note: If requested, enter your code to unlock all channels.

(See TV, Features menu, Childlock, p. 12.)

é Press the cursor down.

Follow the instructions on screen.

Note: Search or direct selection of a TV channel.

If you know the frequency, the C- or S-channel number, enter the 3

or 2 digits of the frequency or the channel number directly with

the digit keys 0 to 9 (e.g. 048). Press the cursor down to proceed.

Repeat to search for another TV channel.

Manual install

Install

Selection mode

System

Programme

Search

Fine tune

Store

Store TV channels

2260.2 en 30-09-2003 14:58 Pagina 6

It is possible to change the name stored in the

memory or to assign a name to a TV channel or

external for which a name has not yet been

entered.A name with up to 5 letters or numbers

can be given to the programme numbers 0 to 99.

Note : It is not possible to rename the VGA source.

& Select Give Name in the Install menu and

press the cursor down.

é Select the programme number.

Note: keep the cursor up/down pressed to scroll

through the programme list quickly.

“ Press the cursor right.

A keyboard appears on the screen.

Press the cursor right to enter the keyboard.

Press the cursor up/down, left/right to select

the first character and press

OK. Repeat for

every character you want to enter.

Select

Space to enter a space; Delete to erase

the highlighted character in the name entered;

Shift to display upper- or lowercase characters

on the keyboard;

Special to display special

characters on the keyboard. Press

OK to

confirm.

‘ Press the cursor left repeatedly when you have

finished the name giving.

( Select another programme number and repeat

steps

“ to ‘.

7

Give name

pπ

® Space ® Delete

ABCDEFG 123

HIJKLMN 456

OPQRSTU 789

VWXYZ 0

® Shift ® Special

Give name

Install

VCR1

BBC1

BBC2

CNN

TVE

.....

Reshuffle the programme list

You can change the order of the stored TV

channels.

& Select Reshuffle in the Installation menu.

é Follow the instructions on screen.

Select Favourite TV channels

A VGA source always belongs to the list of

Favourite programmes.

& Select Favourite programmes in the Install

menu.

é Select your programme number with the

cursor up/down.

“ Select Ye s or No with the cursor right.

‘ Repeat é and “ for every TV channel or

external you want to make a favourite or a

non-favourite TV channel or external.

TV Setup

The Setup menu contains items that control the settings

of the TV’s functions, features, services and peripherals

you may have connected.

The

General menu allows you to change settings that

will typically be accessed only occasionally.

The

Source menu allows you to select a source.

The

Decoder menu allows you to define one or more

programme numbers as decoder programme numbers.

General

Menu background

Factory settings

NEXTVIEW provider

OSD

Programme title

Teletext level 2.5

Auto surround

Set/Change code

Setup

2260.2 en 30-09-2003 14:58 Pagina 7

8

General

Menu background

Select

Ye s or No to turn the menu background

on or off.

Factory settings

This resets the picture and sound settings to

their predefined factory values, but maintains

the channel installation settings.

NEXTVIEW provider

Select a TV broadcaster that provides

NEXTVIEW data. How to make use of NEXTVIEW,

see p. 13.

OSD (On Screen Display)

See Use of the remote control, p. 3, i On

screen information.

& Select OSD.

é Select Normal to activate the continuous

display of the programme number.Also TV

channel and programme information are

extended.

Minimum will display reduced

channel information.

Note: When subtitles is switched on, see Features,

p.12, continuous display of the programme number

is not possible.

Programme title

Select

Programme title Yes or No.

When selected

Ye s, after the selection of a TV

programme or after pressing the i key on

the remote control, a TV channel which

broadcasts teletext may transmit the name of

the TV channel or the programme title.

When selected

No, the programme title will

only appear after pressing the i key, and not

after the selection of a TV channel.

Teletext level 2.5

Some broadcasters offer the opportunity to see

more colours, other background colours and

nicer pictures in the teletext pages.

& Select Teletext level 2.5.

é Press the cursor right to select Teletext level

2.5 On

to take advantage of this feature.

“ Press the cursor right again to select Teletext

level 2.5 Off

if you like the more neutral

teletext layout.

The selection made is valid for all channels

which broadcast teletext level 2.5.

Note: It may take a few seconds before teletext

broadcast switches over to Teletext level 2.5.

Auto Surround

Sometimes the broadcaster transmits special

signals for Surround Sound encoded

programmes.

The TV automatically switches to the best

surround sound mode when

Auto Surround is

switched

On.

Set/Change code

The Child lock feature (see TV, Features, p. 12)

allows you to lock channels to prevent others

from watching certain programmes.To watch

locked channels, a 4-digit code must be entered.

The Set/Change code menu item allows you to

create or change a Personal Identification

Number (PIN).

& Select Set/Change code.

é If no code exists yet, the menu item is set to

Set code.

If a code has previously been entered, the menu

item is set to

Change code.Follow the

instructions on screen.

Important:You have forgotten your code !

& Select Change code in the General menu and

press

OK.

é Press the cursor right and enter the overriding

code 8-8-8-8.

“ Press the cursor again and enter a new

personal 4-digit code.The previous code is

erased and the new code is stored.

This menu allows you to change various settings that are presumably adjusted less frequently than

most other settings.

Press the i key on the remote control to get information about the selected menu item.

2260.2 en 30-09-2003 14:58 Pagina 8

9

Source

This menu allows you to indicate the peripheral

you connected to one of the external inputs.

& Press the cursor right to enter the list of types

of peripherals attached to the selected input.

é Select the peripheral device with the cursor

up/down.

Once you have selected the source type, e.g. DVD,

this source will automatically be selected when

your remote control is in DVD mode, see p. 3, and

when you press the v key on the remote

control.

Centre input - Centre in volume

When you have connected a surround receiver

to the TV, see p. 18, the loudspeakers of the TV

can act as centre speaker, making a separate

centre speaker unnecessary.

Select

Centre input On or Cinema Link (in

case you have connected a Cinema Link

Surround receiver).

When having selected

On you can adjust the

Centre in volume with the cursor left/right to

correct volume level differences of the external

audio receiver and speakers.

Note:This is not the case with a Cinema Link

surround receiver.

Source

EXT1

EXT2

EXT3

YPbPr

Centre input

Centre in volume

Setup

If a decoder or a descrambler is connected, see

p. 17, you can define one or more programme

numbers as decoder programme numbers.

& Select Decoder with the cursor right.

é Select Programme.

“ Select the programme number under which

you have stored the programme coming from

your decoder.

‘ Select Status.

• Select the input used to connect your

decoder:

None, EXT1 or EXT2.

• Select

None if you do not want the selected

programme number being activated as a

decoder programme number.

Note: Select

EXT2 when the decoder is connected to

your EasyLink video recorder.

Decoder

Programme

Status

Setup

Demo

The Demo menu allows to demonstrate the TV

features separately or in a continuous loop.

If

Auto demo has been selected the demo will

automatically present the features sequentially in a

loop. Press one of the cursor keys to stop the Auto

demo.

If one of the features has been selected, this

particular feature demo will run only once, and the

Demo menu will reappear.

Note:The Dealer demo is not part of the automatic

sequence and can only be activated separately.

Auto demo

......

Dealer demo - Dig natural motion

- Light sensor

- Comb filter

TV

Setup

Demo

Install

2260.2 en 30-09-2003 14:58 Pagina 9

& Press the cursor right to select Picture.

é Select the menu items in the Picture menu with the cursor

up/down.

“ Adjust the settings with the cursor left/right or enter the list of

submenu items with the cursor right. Select a submenu item

with the cursor up/down.

Note:To remove the menu background before adjusting the picture

settings, see Select TV setup, General, p. 7.

Smart picture

Select

Smart picture to display a list of predefined picture

settings, each corresponding with specific factory settings.

Personal refers to the personal preference settings of picture in

the picture menu.

Dig natural motion

Line doubling eliminates line flicker, motion compensation

reduces jitter and offers smooth, yet sharp motion reproduction

in movie broadcasts.

Select

On or Off to really see the difference in picture quality.

Dynamic contrast

Sets the level at which the TV automatically enhances the details

in dark, middle and light areas of the picture.

DNR

This sets the level at which noise is measured and reduced in

the picture.

Colour enhancement

This makes the colours more vivid and improves the resolution

of details in bright colours.

Hue

This compensates for the colour variations in NTSC encoded

transmissions.

Picture format

This will adjust the size of the picture dependent on the

broadcast format and your preferred setting.

TV menu

Press the MENU Ï key on the remote control to summon the main menu.

Note: Dependent on the input signal, one or more menu items may not be selectable.

Press the i key on the remote control to get information about the selected menu item.

Picture Sound Features

Smart picture

Contrast

Brightness

Colour

Sharpness

Tint

Dig natural motion

Dynamic contrast

DNR

Colour enhancement

(Hue)

Picture format

TV

10

Picture menu

2260.2 en 30-09-2003 14:58 Pagina 10

11

The TV continuously measures and corrects all

incoming signals in order to provide the best

picture possible.

& Press the h key on the remote control.

é The Active Control menu appears.

“ Press the cursor up/down to select the Active

Control values

Off, Minimum, Medium

(recommended) or Maximum.

The picture settings are being optimised

continuously and automatically which is

displayed by bars.The menu items can not be

selected.

‘ Press the cursor right to select Smart

Picture

.

( Press the cursor up/down to select one of the

predefined picture settings.

§ Press the cursor right to select Active

Display

.

è Press the cursor up/down to select Show bars,

one of the Dual screen demos or

Off.

When you select Dynamic contrast, Digital

Noise Reduction or Digital Natural Motion, the

TV screen is divided into two parts: in the left

part the selected picture quality setting is

switched off; in the right part it is switched on.

Note: Dependent on the input signal, one or more

Dual screen demos may not be selectable.

! Press the h key again to switch off the Active

Control menu.

Active Control

& Press the cursor right to select Sound.

é Select the menu items in the Sound menu with the cursor

up/down and adjust the settings with the cursor

left/right.Remember, control settings are at normal mid-range

levels when the bar scale is centred.

Smart sound

Select

Smart sound to display a list of predefined sound

settings, each corresponding with specific factory settings of

Treble and Bass.

Personal refers to the personal preference

settings of sound in the sound menu.

Notes:

- Some menu items are only available in case of a Cinema Link

configuration and when the Cinema Link is activated. Others are

steered by the audio receiver instead of by the TV. See the separate

Cinema Link booklet supplied.

- Dual X is only available with dual sound transmission.

-Mono/Stereo is only selectable in case of analogue stereo

transmission.

-Nicam/Analogue is only selectable in case of Nicam transmission.

Sound

Smart sound

Equalizer

Volume

Balance

Loudness

Headphone volume

Surround mode

(Dual I-II)

(Mono/Stereo)

(Nicam/Analogue)

(3D effect)

AVL

Delta volume

TV

Sound

Off

On

On during mute

Features

Programme list

Subtitle

Sleeptimer

Child lock

On timer

Zoom

TV

Features menu

& Press the cursor right to select Features.

é Select the menu items with the cursor

up/down and adjust the settings with the

cursor left/right.

Use the on-screen Menu-Info i for more

information about the menu items.

2260.2 en 30-09-2003 14:58 Pagina 11

12

Programme list

Press the

OK key to switch over to the

selected TV channel or external.

Select subtitles

The subtitle page must be stored for each TV

channel:

Switch on teletext and select the proper

subtitle page from the index. Switch off

teletext.

Subtitle On will automatically display them on

the selected TV channels if subtitles are in the

transmission.A symbol will indicate that the

mode is on.

Select

On during mute when you want to

have the subtitles automatically displayed only

when the sound has been muted with the ¬

key on the remote control.

Child lock

Note: A VGA source can not be locked.

& Select Child lock.

é Press the cursor right to enter the Child lock

menu.You’re summoned to enter your code.

Note:You have to re-enter your code each time you

enter the child lock menu.

Important:You have forgotten your code !

See p. 8.

“ Select one of the menu items of the child lock

menu:

•

Lock if you want to lock all channels and

externals.

•

Custom lock and press the cursor right.

The items Age lock and Category lock are only

available when

NEXTVIEW broadcast is available.

Select:

-

Age lock if you want to lock programmes

related to a certain age: off, 2, 4 ... 18;

-

Lock after if you want to lock all

programmes from a certain time onwards.

Press the cursor right and enter the time

with the cursor up/down and right. Press the

OK key to validate.

-

Programme lock if you want to lock a

certain TV channel or external;

-

Category lock if you want to lock

programmes related to a certain theme:

Movies, Sports, Shows....

• Select

Unlock to disable all locks you have set.

On timer

& Select On timer with the cursor down.

é Select On with the cursor right.

“ Press the cursor right again to enter the

programme list.

‘ Select the TV channel or external you want

your TV to switch to on a selected time and

day.

( Press the cursor right again to select a day of

the week or to select

Daily.

§ Press the cursor right once again to enter the

time with the digit keys or with the cursor

up/down and press the

OK key to activate.

è Press the MENU Ï key to turn off the menu.

Note:To check your timer settings, press the i

key.

Zoom

Note: Dependent on the input signal, Zoom may not be

selectable.

& Select Zoom with the cursor down and press

the

OK key.

é Press the OK key to select one of the zoom

magnifications (x1, x4, x9, x16).

“ Additionally you can shift the selected zoom

window over the screen with the cursor keys

up/down, left/right.

‘ Press the MENU Ï key to turn off the zoom

function.

VCR1

BBC2

CNN

TVE

π.....

Sunday

Monday

.......

Daily

15:45

On timer

Off

On

Child lock

Lock

Custom lock

Unlock

Age lock

Lock after

Programme lock

Category lock

2260.2 en 30-09-2003 14:58 Pagina 12

1313

NEXTVIEW / Teletext guide

NEXTVIEW is an electronic guide that allows you to look up programmes as you would in a

newspaper or a TV magazine.You can sort the programmes by subject (films, sport...), obtain

detailed information and programme your video recorder if it comes with the

NEXTVIEWLink

function.

Important note: The

NEXTVIEW service is only available on certain programmes and in certain

countries. When no

NEXTVIEW information is broadcast, the teletext programme guide appears in its place. This is

based on teletext programme information (if available) and offers most functions of

NEXTVIEW.

Note:The broadcaster is responsible for the content of the information.

Call NEXTVIEW / Teletext guide

Press the æ key on the remote control to call the NEXTVIEW/Teletext guide. A menu appears with

the message One moment please.After a while you obtain:

•a

NEXTVIEW page, if the selected channel broadcasts this service (the NEXTVIEW logo is displayed),

•a teletext page, if the selected channel does not broadcast

NEXTVIEW,

•

No information available is displayed if neither NEXTVIEW nor teletext are transmitted. In this case,

select another channel.

Display of a

NEXTVIEW page

The information is set by the channel that transmits the

NEXTVIEW

service. See also Setup menu,

General,

NEXTVIEW provider, p. 8.

This logo is only displayed

during a NEX

TVIEW

transmission or when one

of the externals is selected.

No logo indicates a teletext

programme guide

Programme name and

broadcast time

Review Record Remind Watch Lock

Mon 03

Tue 04

Wed 05

Thu 06

Fri 07

Sat 08

puck

function keys

NEXTVIEW guides

BBC1 18.00 BBC News

BBC2 18.00 The Simpsons

CNN 18.00 World News

FR2 18.00 On a tout essayé!

CH5 18.15 Tomorrow Never Dies

Menu 18.00 Channel Theme

Mon 05

Feb 18.00

NEXTVIEW guides

& Use the cursor key left/right to select Time, Channel, Theme, the Date guide (or menu).

The

Time guide provides an overview of all programme titles active in the selected time block.The

Channel guide provides an overview of all programmes that are broadcast by a single channel during

one day. With the

Date guide you can choose a specific date.The Theme guide displays a list of all

programmes at the selected date, that matches with the selected category.

Going through the menu guide, the TV is collecting the sorting criteria to finally display a list of

programme events.

é Press the OK key to select the guide type.

“ Move the puck down and to the right to select the programmes.

If available a summary or commentary on the programme is displayed at the bottom of the screen.

‘ Use the cursor up/down to scroll through the programmes.

2260.2 en 30-09-2003 14:58 Pagina 13

1414

Teletext Guide

& Enter with the digit keys, the teletext page number that contains the programme information for the

current channel.

é Press the cursor right to move the puck over the selection ball.

“ Use the cursor up/down to scroll through the different programmes.

• If the selected programme contains a page number with an optional subcode referring to a page with

more info about the programme, press the

OK key to display the information. Press the OK key again

to return to the programme guide page.

• If the selected programme guide page satisfies the VPT requirements,

- it will be possible to record, remind, watch or lock programmes:

- the TV will remember the last selected teletext page number of that channel that contains programme

guide information and indicates which programme starts at what time. Every time you press the æ

key, the teletext programme guide page of the selected TV channel will be available.

• When necessary you can select the subpage number by moving the cursor to the pageball and

pressing right.

Note:You must enter the teletext pagenumber for each channel.You can change the channels also by moving

the cursor up/down in the list in the left of the page.

Basic functions

Press one of the grey, red, green, yellow or blue keys to activate a

NEXTVIEW or Teletext Guide

function.The keys appear in grey if the function is not available.

Review: this menu provides a list of programmes that are marked as reminders, those that have to be

recorded and those that are locked.This menu can be used to change or remove marked

programmes.

Record: to programme the recording of the video recorder (if it has a NEXTVIEWLink function and is

connected to

EXT. 2).

Remind: automatically switch on the TV if it is in standby or by displaying a message if the TV is on.

Lock: to lock certain programmes to prevent recording or watching.

For the functions Record, Remind or Lock, a small menu pops up in which you can choose the

interval: once, daily or weekly, or clear an earlier made record, remind or lock setting.The default

interval is set to

Once.To confirm the frequency, press the OK key.

Watch: to watch the selected and currently broadcast programme.

Acquisition and updating of NEXTVIEW information

Acquisition and updating of NEXTVIEW is done when you are watching the TV channel of the selected

NEXTVIEW provider, see Setup menu, p. 8, or when the TV is switched to standby;

Acquisition of fresh data will happen once during the night.

Note: it may be necessary to put the TV in standby mode when all

NEXTVIEW information is outdated, e.g. when

returning from holiday.

Review Record Remind Watch Lock

BBC1

BBC2

ITV

CH4

CH5

page ball

selection ball

channel list

Mon 05 Feb 16.35

100 1

BBC CEEFAX

LIONS RECORD ANOTHER WIN 430

Index 100 News 300

BBC Info 110 Headlines 305

Children 120 Weather 400

Cookery 150 Sports 415

Education 200 Radio 500

subpages

scroll ball

2260.2 en 30-09-2003 14:58 Pagina 14

1515

Switch Teletext on and off

Press b to switch the teletext on.

Select a Teletext page

- Enter the desired page number with the digit

keys, the cursor keys up/down or with the -P+

key.

- Select the options at the bottom of the screen

with the colour keys.

Previously selected teletext page

(Only possible in case there is no list of favourite

teletext pages available. See p. 16.)

Press the 0 key.

Select the index teletext page

Press the grey colour key † to display the

main index (usually p.100).

Only for T.O.P teletext broadcasts:

Press i.A T. O.P. overview of the teletext

subjects available is displayed.

Select with the cursor up/down, left/right the

desired subject and press the

OK key.

Not all TV channels broadcast T.O.P. teletext.

Select subpages

When a selected teletext page consists of

different subpages, a list of available subpages

appears on the screen.

Press the cursor left or right to select the next

or previous subpage.

Enlarge a Teletext page

Press q repeatedly to display the upper

teletext part, the lower teletext part and then

to return to the normal teletext page size.

When the teletext page is enlarged, you can

scroll the text, line by line using the cursor

up/down.

Hypertext

With hypertext you can quickly jump to a

pagenumber or search for a specific word

shown on the current teletext page.

& Press the

OK key to highlight the first word or

a number on the page.

é Use the cursor up/down, left/right to select any

other word or number you want to search for.

“ Press the OK key to confirm.The search starts.

A message appears at the bottom of the screen

to indicate the searching, or that the word or

page is not found.

‘ Use the cursor up to exit hypertext.

Most TV channels broadcast information via teletext.This TV has a 1200 pages memory that will store

most broadcasted pages and subpages to reduce waiting time. After each programme change, the

memory is refreshed.

Teletext

LIONS RECORD ANOTHER WIN 430

Index 100 News 300

BBC Info 110 Headlines 305

Children 120 Weather 400

Cookery 150 Sports 415

Education 200 Radio 500

Lottery 230 Travel 550

Finance 240 Subtitling 888

Music 280 TV Listings 600

Red Green Yellow Blue

102 «03 04 05 06 07 08 09 10 11 12»

BBC CEEFAX 102 Mon 05 Feb 16.35.22

BBC CEEFAX

2260.2 en 30-09-2003 14:58 Pagina 15

1616

Teletext menu

& Press the MENU Ï key to activate the menu.

é Press the cursor up/down to select the menu

items.

“ Press the cursor right to activate.

Reveal

Reveals/conceals hidden information on a page,

such as solutions to riddles and puzzles.

Press the cursor right to activate.

Favourite

You may create a list of eight favourite teletext

pages in total, selected from various TV

channels.

To add a favourite page to the list:

& Select a favourite teletext page.

é Select Favourite in the teletext menu and

press the cursor right to enter the list.

“ Press the cursor right again to add the page.

‘ Press the MENU Ï key to watch the current

page.

To watch a favourite page from the list:

When in Teletext, use the 0 key to browse

through the favourite pages of the TV channel

actually selected.

Note: only the pages of the current channel can be

selected.

Search

Selecting a word

On the keyboard on screen you can type in a

random word you want to search for in the

teletext pages.Whether upper- or lowercase is

used has no influence.

& Press the cursor right to enter the keyboard.

é Press the cursor left/right, up/down to select

the characters, words or functions.

“ Press the OK key to confirm each character

selected.

‘ Select Cancel to cancel the word; Space to

enter a space;

Delete to delete the last

character selected;

Shift to switch between

lowercase or capital characters;

Special to

display special characters on the keyboard and

press the

OK key.

( Press the cursor left repeatedly to return to

the Teletext menu again.

Searching a word

& Type in the word on screen or select a word

from the history list on the right and press

OK.

é Select Accept and press OK again.The message

Searching appears.

“ To cancel the searching or to search for a new

word, select

Keyboard and press OK.

‘ When a word is not found, a message appears.

When the word is found, it is highlighted in the

teletext page.To continue the search, press the

OK key.

Cycle subpages (if available)

Makes the subpages cycle automatically.

Press the cursor right to activate and to de-

activate again.

Timed page

To display a specific page from a selected TV

channel at a certain time.

& Press the cursor right and select Ye s or No.

é Enter the time and pagenumber with the cursor

keys or the digit keys.

Note:Teletext does not have to remain switched on,

but you should watch the TV channel you have

selected the specific page from.

“ Press the cursor left to return to the TV menu

again.

Language

If the displayed characters on screen do not

correspond with the characters used by the

teletext broadcaster, you can change the

language group here.

Select

Group 1 or 2 with the cursor right.

Press the

MENU Ï key to leave the Teletext

menu.

102 03 04 05 06 07 08 09 10 11 12

TELETEXT

BBC1

Red Green Yellow Blue

puck

Cancel Accept

Space Delete

ABCDEFG 1 2 3

HIJKLMN 4 5 6

OP QRSTU 7 8 9

V W X Y Z 0

Shift Special

WORD

NAME

FOOTBALL

2260.2 en 30-09-2003 14:58 Pagina 16

17

There is a wide range of audio and video equipment that can be connected to your TV.

The following connection diagrams show you how to connect them.

Note:

EXT 1 can handle CVBS and RGB; EXT 2 CVBS, Y/C and RGB; EXT 3 CVBS and Y/C; YPbPr Y-Pb-Br 480p,

576p, 1080i;

VGA IN can hancle VGA, SVGA and 480p, 576p, 1080i.

It is preferred to connect peripherals with RGB output to

EXT 1 or EXT 2 as RGB provides a better picture quality.

Note: If your recorder is provided with the EasyLink function, it should be connected to

EXT 2 to benefit from the

EasyLink functionality.

Recorder (VCR

-DVD+RW)

Note: Do not place your recorder too close to the screen as some recorders may be susceptible for signals out of the

display. Keep a minimum distance of 0,5 m to the screen.

RRPr

Pb

Y

EXT1EXT3

LL

VGA

CENTRE

IN

EXT2

VCR 1 DECODER

4

3

2

CABLE

1

RRPr

Pb

Y

LL

VGA

CENTRE

IN

EXT2

CABLE

1

2

VCR 1

4

3

5

Connect Peripheral Equipment

Connect the aerial cables 1, 2 and, to obtain the

optimum picture quality, eurocable 3 as shown.

If your recorder does not have a euroconnector, the

only possible connection is via the aerial cable.You will

therefore need to tune in your recorder’s test signal and

assign it programme number 0 or store the test signal

under a programme number between 90 and 99, see

Manual installation, p. 6.

See the handbook of your recorder.

Decoder and Recorder

Connect a eurocable 4 to your decoder and to the

special euroconnector of your recorder. See also the

recorder handbook. See Decoder, p. 9. You can also

connect your decoder directly to

EXT1 or 2 with a

eurocable.

Other equipment

(satellite receiver, decoder, DVD, games, etc.)

& Connect the aerial cables 1, 2 and 3 as shown

(only if your peripheral has TV aerial in-/output).

Connect your equipment with a eurocable 4 or 5 to

one of the euroconnectors

EXT1, 2 or 3 to obtain a

better picture quality.

é Look for the test signal of your peripheral in the same

way as you do for a recorder.

“ Make a selection in the Setup, Source menu, p. 9.

R

L

VGA

CENTRE

IN

DVD

L

R

Y

Pb

Pr

1

Equipment with Component Video Output Connectors (

YPbPr

)

& Connect the three separate component video cables

1 to the DVD player’s

Y, U (Pb) and V (Pr) jacks and

to the Y, Pb and Pr jacks on the TV.

é Connect the audio cable to the DVD player’s AUDIO L

and R jacks and to the L and R audio YPbPr jacks on

the TV.

2260.2 en 30-09-2003 14:58 Pagina 17

18

Multi channel Surround receiver

& Connect the audio cable to the multi channel Surround receiver

and to

AUDIO OUT L and R at the bottom of your TV 1.

é If you want the loudspeakers of your TV to act as centre

speaker, also connect an audiocable to the multi channel

Surround receiver and to the

CENTRE IN at the bottom of

your TV 2.

“ Select Centre Input On in the Source menu. See p. 9.

The loudspeakers of the TV will now only produce centre

sound, the loudspeakers connected to the audio receiver will

produce Surround Sound.The volume has to be controlled via

the multi channel Surround receiver.

Note: No sound will be heard when a TV channel or external source is

blocked via the Child lock menu (see p. 12).

R

L

VGA

L

R

2

CENTRE IN

AUDIO

OUT

1

Headphone

& Insert the plug into the headphone socket L as shown.

é Press ¬ on the remote control to switch off the internal

loudspeakers of the TV.

The headphone impedance must be between 8 and 4000 Ohm.The

headphone socket has a 3.5 mm jack.

In the Sound menu select

Headphone volume to adjust the

headphone volume.

R

L

VGA

CENTRE

IN

Press the v key on the remote control repeatedly, or select Source in the Setup menu (see p. 9) to

select

EXT1, EXT2, EXT3, YPbPr or VGA according to where you connected your equipment.

Remark : Most equipment (decoder, recorder) carries out the switching itself, when it is switched on.

To select connected equipment

2260.2 en 30-09-2003 14:58 Pagina 18

La pagina sta caricando ...

Philips 42PF9945/12 Manuale utente

Questo manuale è adatto anche per

Philips 42PF9945/12 Manuale utente

in altre lingue

Documenti correlati

Altri documenti