Panasonic VDR-M30PP Manuale utente

DVD Palmcorder

Operating Instructions

Model No. VDR-M30PP

Thank you for buying a Panasonic product. Please take time to become familiar with the operating

instructions and how it is set up. Keep it handy for future reference.

Quick Start Guide for Software on page 12

This instruction manual uses recycled paper certified by the Eco Mark.

VQT0E25

QR34662

R

For USA assistance, please call: 1-800-211-PANA(7262) or send e-mail to : [email protected]

For Canadian assistance, please call: 1-800-561-5505 or visit us at www.panasonic.ca

VDR-M30PP_GB.book Page 1 Friday, March 14, 2003 8:53 PM

QR34662

2

Important Information

For Your Safety

The power switch turns the DVD Palmcorder on and off, leaving the date/time feature unaffected. If the camera/recorder

is to be left unattended for a long period of time, turn it off .

The DVD Palmcorder and AC adapter/charger have

the following caution marks.

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT OPEN.

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL.

Precautions

WARNING: Many television programs and films

are copyrighted. In certain circumstances, copy-

right law may apply to private in-home

videotaping of copyrighted materials.

Identifications of caution marks

This symbol warns the user that

uninsulated voltage within the unit

may have sufficient magnitude to cause

electric shock. Therefore, it is dangerous

to make any kind of contact with any

inside part of this unit.

This symbol alerts the user that

important literature concerning the

operation and maintenance of this unit

has been included. Therefore, it should

be read carefully to avoid any problems.

WARNING : TO PREVENT FIRE OR SHOCK HAZARD, DO NOT

EXPOSE THIS UNIT TO RAIN OR MOISTURE.

WARNING : TO PREVENT FIRE OR SHOCK HAZARD, USE THE

RECOMMENDED ACCESSORIES ONLY.

WARNING: TO PREVENT FIRE OR SHOCK HAZARD, BE

SURE TO USE THE SPECIFIED AC ADAPTER/CHARGER

(PV-DAC13).

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

The liquid crystal display (LCD) panel is made

by highly precise technology. More than 99.99%

of its picture elements (pixels) are effective, but

some (less than 0.01%) may appear as colored

bright dots. This does not indicate a fault as the

LCD panel stretches the limits of current

technology.

CLASS 1

LASER PRODUCT

CAUTION

This product contains a laser diode of higher

class than 1. To ensure continued safety, do not

remove any covers or attempt to gain access to

the inside of the product. Refer all servicing to

qualified personnel.

VDR-M30PP_GB.book Page 2 Friday, March 14, 2003 8:53 PM

3

QR34642

Microsoft

®

, Windows

®

, Windows

®

98, Windows

®

98 Second Edition, Windows

®

Me, Windows

®

2000

Professional, and Windows

®

XP are registered trademarks of Microsoft Corporation.

Intel

®

, Pentium

®

Processor, and Celeron

®

Processor are registered trademarks of Intel Corporation.

IBM

®

and PC/AT

®

are registered trademarks of International Business Machines Corporation.

Manufactured under license from Dolby Laboratories.

“Dolby” and the double-D symbol are trademarks of Dolby Laboratories.

Other company names and product names listed are trademarks or brand names belonging to each

individual company.

SD logo is a trademark.

FCC Note: This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates, uses,

and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no guarantee

that interference will not occur in a particular installation. If this equipment does cause harmful

e

n

ce

to radio or television reception, which can be determined by turning the equipment off and

user

is encouraged to try to correct the interference by one or more of the following measures:

•

e

nt or relocate the receiving antenna.

•

In

c

r

ease

the separation between the equipment and receiver.

•

C

o

n

ec

t the equipment into an outlet on a circuit different from that to which the receiver is connected.

•

n

s

u

lt th

e

dealer or an experienced radio/TV technician for help.

F

C

Ca

u

t

i

on: To assure continued compliance, follow the attached installation instructions and use

only shielded interface cables with ferrite core when connecting to computer or peripheral devices.

Any changes or modifications not expressly approved by the party responsible for compliance could

void the user’s authority to operate this equipment.

Declaration of Conformity

Trade Name: Panasonic

Model No.: VDR-M30PP

Responsible party: Matsushita Electric Corporation of America

One Panasonic Way, Secaucus, NJ 07094

Support Contact: Panasonic Consumer Electronics Company

1-800-211-PANA (7262)

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1)This device may not cause harmful interference, and (2) this device must accept

any interference received, including interference that may cause undesired operation.

This class B digital apparatus complies with CANADIAN ICES-003.

This Product has a fluorescent lamp that contains a small amount of mercury. It also contains

lead in some components. Disposal of these materials may be regulated in your community

due to environmental considerations. For disposal or recycling information please contact your

local authorities, or the Electronics Industries Alliance: <http://www.eiae.org

.>

A lithium ion/polymer battery that is recyclable powers the product

you have purchased. Please call 1-800-8-BATTERY for information

on how to recycle this battery.

U.S.A./CANADA CONSUMERS: ATTENTION:

VDR-M30PP_GB.book Page 3 Friday, March 14, 2003 8:53 PM

4

QR34642

Be sure to read the following before opening

the package of CD-ROM

This Agreement will take effect at the moment you open the package of the storage device (CD-ROM) provided with this

product, if you agree to the terms herein.

If you do not accept the terms of this Agreement, immediately return the unopened package of storage medium and

enclosed materials (printed matter, external package, and all others) to your dealer, or return only the package of storage

medium to your dealer.

Consult your dealer for any refund on the unused product. However, if only the package of storage medium is returned,

no refund is possible.

This License Agreement certifies that you were granted license in the past.

License Agreement

Article 1 Grant of License

Matsushita Electric Industrial Co., Ltd., grants you the following rights for the following products (to be referred to as

“This Software” hereafter) that you have obtained with this Agreement:

(a) You may use This Software only on a single piece of equipment. However, if this equipment cannot

be used because of mechanical problem, you may temporarily use This Software on another piece of

equipment.

(b) Although This Software contains several components that can be run on computer as independent

functions, all components are licensed as a single product: You may not, by any means, use these

components on different computers at the same time.

Article 2 Copyrights

The copyrights of This Software, attached manual, etc. are owned by the following corporations, and are protected by

copyright laws in Japan and USA, as well as by other intellectual property and international properties:

Article 3 Other Rights and Limitations

(

a) You may not copy This Software or any of the printed materials attached, except for duplications to provide back-

up or storage.

(b) Use of This Software by third parties is prohibited, whether by transferring, renting, leasing, lending, moving, or

any other measures.

(c) You may not decompile or disassemble this Software.

(d) Duplication and/or distribution of any files on this storage medium for commercial use is prohibited.

Article 4 Quality Assurance

Under no circumstances will Matsushita Electric Industrial Co., Ltd. Hitachi, Ltd., or Sonic Solutions accept any

responsibility for any damages you may incur from using or being unable to use This Software (including, but not limited

to, loss of business profit, interruption of business, loss of business information, or other monetary damages).

Article 5 Termination of Agreement

If you fail to comply with the terms of this Agreement, Matsushita Electric Industrial Co., Ltd. Hitachi, Ltd., and Sonic

Solutions reserve the right to terminate the Agreement. In such a case, you will be obliged to discard all copies of This

Software and its components.

Article 6 Prioritized License Agreement

When some software programs are installed, the license agreements will be displayed (to be referred to as online license

agreement).

If the online license agreement conflicts with this Agreement, the online license agreement shall have a priority.

Name of Software Copyright Owners

USB driver Hitachi, Ltd.

DVD-RAM Driver Matsushita Electric Industrial Co., Ltd.

DVD-MovieAlbumSE Matsushita Electric Industrial Co., Ltd.

MyDVD Sonic Solutions

VDR-M30PP_GB.book Page 4 Friday, March 14, 2003 8:53 PM

5

QR34642

IMPORTANT SAFEGUARDS

In addition to the careful attention devoted to quality standards in the manufacture of your video product, safety is a major

factor in the design of every instrument. But, safety is your responsibility too.

This page lists important information that will help to assure your enjoyment and proper use of DVD Palmcorder and

accessory equipment. Please read it carefully before operating your video product and keep it in a handy place for future

reference.

INSTALLATION

1 Read and Follow Instructions — All the safety and

operating instructions should be read before the video

product is operated. Follow all operating and use

instructions.

2 Retain Instructions — The safety and operating

instructions should be retained for future reference.

3 Heed Warnings — Comply with all warnings on the

video product and in the operating instructions.

4 Power Sources — This video product should be

operated only from the type of power source indicated

on the marking label. If you are not sure of the type of

power supply to your home, consult your video dealer

or local power company. For video products intended

to operate from battery power, or other sources, refer

to the operating instructions.

5 Overloading — Do not overload

wall outlets and extension cords

as this can result in a risk of fire or

electric shock. Overloaded AC

outlets and extension cords are

dangerous, and so are frayed

power cables, damaged or

cracked wire insulation and

broken plugs. They may result in

a shock or fire hazard. Periodically examine the cord

and have it replaced by your service technician if

appearance indicates damage or deteriorated

insulation.

6 Power-Cord Protection — Power-supply cords

should be routed so that they are not likely to be walked

on or pinched by items placed upon or against them,

paying particular attention to cords at plugs,

convenience receptacles, and the point where they

exit from the appliance.

7 Ventilation — Slots and openings in the cabinet are

provided for ventilation to ensure reliable operation of

the video product and to protect it from overheating.

These openings must not be blocked or covered. The

openings should never be blocked by placing the video

product on a bed, sofa, rug, or other similar surface.

This video product should never be placed near or over

a radiator or heat register. This video product should

not be placed in a built-in installation such as a

bookcase or rack unless proper ventilation is provided

or the video product manufacturer's instructions have

been followed.

8 Attachments — Do not use attachments unless

recommended by the video product manufacturer as

they may cause hazards.

Caution: Maintain electrical safety. Powerline operated

equipment or accessories connected to this unit should

bear the UL listing mark or CSA certification mark on the

accessory itself and should not have been modified so as

to defeat the safety features. This will help avoid any

potential hazard from electric shock or fire. If in doubt,

contact qualified service personnel.

9 Water and Moisture — Do not use this video product

near water — for example, near a bath tub, wash bowl,

kitchen sink, or laundry tub, in a wet basement, or near

a swimming pool, and the like.

10 Accessories — Do not place this video product on an

unstable cart, stand, tripod, bracket, or table. The

video product may fall, causing serious injury to a child

or adult, and serious damage to the appliance. Use

only with a cart, stand, tripod, bracket, or table

recommended by the manufacturer, or sold with the

video product. Any mounting of the product should

follow the manufacturer's instructions, and should use

a mounting accessory recommended by the

manufacturer.

kawaii koneko

MOMO

key to chise

mekoalbum

cat book

mother

diet

Zoo Docter

Part 1

Zoo Docter

Part 2

sasaki akemi

hirayamo akiko

horie youji setuko kimio

auto moter

kabushiki

mitoniikikata

yakamashii

igarashi

Why?

kuro

abcdfevcdsz

kusano

mitono

kakurai

tadashiigenkou

oomori matuda

nurie

yohsinarish yohsinarishashin

mito

namemekogaikiteita

mito

momogatoiredemizubitashi

album

mame

1

f

u

n

g

a

f

u

n

g

a

f

u

n

g

a

f

u

n

g

a

f

u

n

g

a

f

u

n

g

a

f

u

n

g

a

metsuki

123

nyanko

1

midori

3

okubyo

2

m

o

t

h

e

r

P

a

r

t

2

t

o

m

o

d

a

c

h

i

3

junkaikun

2

momo

3

momo

2

momo

1

ebisu

2

ebisu

1

key

5

key

4

key

3

key

2

key

1

chise

5

chise

4

chise

3

chise

2

chise

1

VDR-M30PP_GB.book Page 5 Friday, March 14, 2003 8:53 PM

6

QR34642

11 An appliance and cart combination

should be moved with care. Quick

stops, excessive force, and uneven

surfaces may cause the appliance

and cart combination to overturn.

12 Power Lines — An outside antenna system should

not be located in the vicinity of overhead power lines or

other electric light or power circuits, or where it can fall

into such power lines or circuits. When installing an

outside antenna system, extreme care should be

taken to keep from touching or approaching such

power lines or circuits as contact with them might be

fatal. Installing an outdoor antenna can be hazardous

and should be left to a professional antenna installer.

USE

13 Cleaning — Unplug this video product from the wall

outlet before cleaning. Do not use liquid cleaners or

aerosol cleaners. Use a damp cloth for cleaning.

14 Object and Liquid Entry — Never push objects of any

kind into this video product through openings as they

may touch dangerous voltage points or short-out parts

that could result in a fire or electric shock. Never spill

liquid of any kind on the video product.

15 Lightning — For added protection for this video

product during a lightning storm, or when it is left

unattended and unused for long periods of time,

unplug it from the wall outlet and disconnect the

antenna or cable-system. This will prevent damage to

the video product due to lightning and power-line

surges.

SERVICE

16 Servicing — Do not attempt to service this video

product yourself as opening or removing covers may

expose you to dangerous voltage or other hazards.

Refer all servicing to qualified service personnel.

17 Conditions Requiring Service — Unplug this video

product from the wall outlet and refer servicing to

qualified service personnel under the following

conditions.

a. When the power-supply cord or plug is damaged.

b. If liquid has been spilled, or objects have fallen into

the video product.

c. If the video product has been exposed to rain or

water.

d. If the video product does not operate normally by

following the operating instructions. Adjust only

those controls that are covered by the operating

instructions. Improper adjustment of other controls

may result in damage and will often require

extensive work by a qualified technician to restore

the video product to its normal operation.

e. If the video product has been dropped or the

cabinet has been damaged.

f. When the video product exhibits a distinct change

in performance — this indicates a need for service.

18 Replacement Parts — When replacement parts are

required, have the service technician verify that the

replacements he uses have the same safety

characteristics as the original parts. Use of

replacements specified by the video product

manufacturer can prevent fire, electric shock or other

hazards.

19 Safety Check — Upon completion of any service or

repairs to this video product, ask the service

technician to perform safety checks recommended by

the manufacturer to determine that the video product

is in safe operating condition.

20 Heat — The product should be situated away from

heat sources such as radiators, heat registers, stoves,

or other products (including amplifiers) that produce

heat.

VDR-M30PP_GB.book Page 6 Friday, March 14, 2003 8:53 PM

7

QR34642

Cautions When Using

Handle the liquid crystal display (LCD) with care:

• The LCD is a very delicate display device: Do not press its surface with force, hit it or prick it with a sharp

object.

• If you push the LCD surface, unevenness in display may occur. If unevenness does not disappear, turn

the DVD Palmcorder off, wait for a few moments, and then turn it on again.

• Do not place the DVD Palmcorder with the open LCD screen down.

• Close the LCD monitor when not using the DVD Palmcorder.

Liquid crystal display and viewfinder:

• The LCD screen and viewfinder are the products of highly precise technology. Among the total number

of pixels (approx. 120,000 pixels for LCD monitor and approx. 110,000 pixels for viewfinder), 0.01% or

less pixels may be missing (black dots) or may remain lit as colored dots (red, blue, green). This shows

the limitations of the current technology, and does not indicate a fault that will interfere with recording.

• The LCD screen and viewfinder will be slightly dimmer than usual when the DVD Palmcorder is at low

temperature, as in cold areas, or immediately after power is turned on. Normal brightness will be

restored when the temperature inside the DVD Palmcorder rises.

Hold the DVD Palmcorder correctly:

• Do not hold the by viewfinder or LCD monitor when lifting the DVD Palmcorder: The viewfinder or

LCD monitor could detach and the DVD Palmcorder may fall.

Do not subject the DVD Palmcorder to impact:

• This DVD Palmcorder is a precision machine. Take great care that you do not strike it against a hard

object or let it fall.

• Do not use the DVD Palmcorder on a tripod in a place where it is subject to severe vibrations or impact.

No sand or dust!

• Fine sand or dust entering the DVD Palmcorder or AC adapter/charger could cause malfunctions or

defects.

No water or oil!

• Water or oil entering the DVD Palmcorder or AC adapter/charger could cause electric shock,

malfunctions or defects.

VDR-M30PP_GB.book Page 7 Friday, March 14, 2003 8:53 PM

8

QR34642

Heat on surface of product:

• The surface of the DVD Palmcorder will be slightly warm, but this does not indicate a fault.

Screen on connected TV:

• Never leave the disc navigation screen, still image or camera image displayed on your TV to which the

DVD Palmcorder is connected: Doing so could result in displayed image retention or phosphor

degradation of TV screen.

Be careful of ambient temperature:

• Using the DVD Palmcorder in a place where the temperature is over 140ºF (40°C) or under 32ºF (0°C)

will result in abnormal recording/playback.

• Take care that the temperature of this DVD Palmcorder, when connected to PC does not rise excessively

(reference for usage: approx. 30 minutes at about 86ºF (30ºC).

• Do not leave the DVD Palmcorder on a beach or in a closed vehicle where the temperature is very high

for a long time: This could cause malfunctions.

Do not point directly at the sun:

• If direct sunlight strikes the lens or viewfinder, the DVD Palmcorder could malfunction or a fire could

occur.

• Do not leave the DVD Palmcorder with the LCD screen exposed to direct sunlight: This could cause

malfunctions.

Do not use the DVD Palmcorder near TV or radio:

• This could cause noise to appear on the TV screen or in radio broadcasts.

Do not use the DVD Palmcorder near strong radio waves or magnetism:

• If the DVD Palmcorder is used near strong radio waves or magnetism, such as near a radio wave tower

or electric appliances, noise could enter video and audio that are being recorded. During playback of

normally recorded video and audio, noise may also be present in picture and sound.

At worst the DVD Palmcorder could malfunction.

Do not expose the DVD Palmcorder to soot or steam:

• Thick soot or steam could damage the DVD Palmcorder case or cause malfunctions.

Do not use the DVD Palmcorder near corrosive gas:

• Using it in a place where there is dense exhaust gas generated by gasoline or diesel engines, or corrosive

gas such as hydrogen sulfide, could corrode the battery connecting terminals, which could result in loss

of power.

Do not use the DVD Palmcorder near ultrasonic humidifier:

• With some water in humidifier, calcium and other chemicals dissolved in water could scatter in the air,

and white particles could adhere to the optical head of the DVD Palmcorder, which could cause it to

operate abnormally.

Do not expose the DVD Palmcorder to insecticide:

• Insecticide entering the DVD Palmcorder could dirty the lens in laser pickup block, and in such a case

the DVD Palmcorder might not operate normally. Turn the DVD Palmcorder off and cover it with vinyl

sheet, etc. before using insecticide.

Do not use a generally available 8 cm CD lens cleaner:

• Cleaning the lens is not necessary when using this DVD Palmcorder in the usual way.

• Using 8 cm CD lens cleaner could cause this DVD Palmcorder to be faulty.

Do not touch the lens in laser pickup block.

• Touching the lens in laser pickup block could cause malfunctions.

VDR-M30PP_GB.book Page 8 Friday, March 14, 2003 8:53 PM

9

QR34642

Be careful of moisture condensation:

• When you move the DVD Palmcorder between places where the difference in temperatures is great -

such as entering a lodge from a ski slope or going out of a cooled room or vehicle - condensation (vapor

in air warmed or cooled to water droplets) could occur on the lens and/or inside the DVD Palmcorder.

If condensation occurs, do not open the cover of disc or card insertion block if possible. If condensation

occurs on the lens, wipe it off with a soft, dry cloth. Even if the external surface of DVD Palmcorder has

dried, condensation may remain inside: Turn the DVD Palmcorder off and leave it in a dry place for at

least 1-2 hours before using it again.

Do not use the DVD Palmcorder for a long, uninterrupted period of time:

• This DVD Palmcorder cannot be used for a long time continuously as a surveillance camera/monitor.

If you use the DVD Palmcorder for a long continuous period of time, the temperature of DVD

Palmcorder could exceed a limit and the recording/playback operation could be slowed down: In this

case, turn it off and wait for a while before using it again.

Do not turn the DVD Palmcorder off while the ACCESS/PC indicator or CARD ACCESS

indicator is lit or blinking:

• The ACCESS/PC or CARD ACCESS indicator is lit or blinking

to show that data is being written to disc or card, or being read

from it. At this time, do not do any of the following, so as not

to damage the data:

− Remove battery pack

− Disconnect AC adapter/charger

− Plug or unplug USB cable

− Remove disc or card

− Subject DVD Palmcorder to severe vibrations or impact.

− Forcefully open or close the LCD monitor

If you turn the DVD Palmcorder off while the ACCESS/PC or CARD ACCESS indicator is lit or blinking,

turn it on again with the disc or card loaded in it: Repair of the disc or card will be executed automatically

(see page 150).

Do not wipe the DVD Palmcorder case with benzene or thinner:

• The coating of case could peel off or the case surface could deteriorate.

• When using a chemical cleaning cloth, follow the instructions.

Also read the instructions attached with optional accessories:

• For optional accessories, observe the cautions and follow instruction manuals attached.

Keep the Memory Card out of reach of children to prevent swallowing.

CARD

ACCESS

indicator

ACCESS/PC

indicator

VDR-M30PP_GB.book Page 9 Friday, March 14, 2003 8:53 PM

10

QR34642

Cautions When Storing

Do not leave the DVD Palmcorder in a place where the temperature is very high for a long

period of time:

• The temperature inside a closed vehicle or trunk can become very high in a hot season. If you leave the

DVD Palmcorder in such a place, it could malfunction or the case could be damaged. Do not expose the

DVD Palmcorder to direct sunlight or place it near a heater.

Do not store the DVD Palmcorder in a place where the humidity is high or in a dusty place:

• Dust entering the DVD Palmcorder could cause malfunctions. If the humidity is high, the lens could be

moldy, and the DVD Palmcorder could become inoperative. It is recommended that you put the DVD

Palmcorder with a desiccant in a box when storing it in a closet, etc.

Do not store the DVD Palmcorder in a place subject to strong magnetism or intense

vibrations:

• This could cause malfunctions.

Detach the battery pack from the DVD Palmcorder and store it in a cool place:

• Leaving the battery pack attached or storing it at high temperature could shorten its life.

Suggestions and Restrictions

Make a trial recording:

• Always make a trial recording before doing actual recording to make sure that recording is normal. The

data that have not been stored normally because of a defect in the DVD Palmcorder cannot be restored.

It is recommended that you use DVD-RAM disc from which recorded contents can be deleted for trial

recording.

Do not use the DVD Palmcorder for professional applications:

• This DVD Palmcorder is designed and produced for home-use recording and playback.

The recorded contents cannot be compensated for:

• Panasonic cannot compensate for any damages caused when recording is not made normally or

recorded contents cannot be played back because of a defect in the DVD Palmcorder, disc or card. Also,

Panasonic cannot be responsible for your recorded video and audio.

• If you or a third party make a mistake when handling this DVD Palmcorder, disc, card, etc., the recorded

contents may be lost. We cannot be responsible for compensation for damage due to loss of recorded

contents.

Copyright:

• Data recorded on the disc or card in this DVD Palmcorder using other digital/analog media or devices

are protected by the copyright act and cannot be used without permission of the owner of copyright,

except for personal enjoyment. Be aware that recording is restricted for some demonstrations,

performances and exhibitions, even for personal enjoyment.

Do not use the DVD Palmcorder for professional applications:

• This DVD Palmcorder is designed and produced for home-use recording and playback.

VDR-M30PP_GB.book Page 10 Friday, March 14, 2003 8:53 PM

11

QR34642

Read This First

To guide you, we've included following six chapters.

• The section on “Setups” explains how to set up

the DVD Palmcorder, battery pack, and set the

date/time.

• The section on “Basic Techniques” explains the

basic operation of this DVD Palmcorder-

recording of movies, still images, external input,

and playback of recorded images.

• The section on “Advanced Techniques” explains

settings on this DVD Palmcorder for more

advanced usage.

• The section on “Disc Navigation” explains

editing with Disc Navigation: Refer to this

section when finalizing DVD-R disc and

initializing DVD-RAM disc.

• The section on “Installing Software” explains the

c o nt e n t s o f p r ov i d e d C D - RO M a nd h o w t o i n st a l l

the contained software included.

• “Subsidiary Information” includes an

introduction to products sold separately, proper

cleaning, and troubleshooting.

We want this manual to be as helpful as possible,

so it includes two easy ways to find the information

you need:

• A quick index for the information you use most

often (this page).

• A detailed table of contents directing you to

specific information quickly.

Get to know your DVD Palmcorder by using this

manual, and get to know Panasonic. We appreciate

your business.

Quick Index

Available Discs................................................. 24

Recording Movie.............................................. 52

Immediately Checking Recorded Scene ......... 69

Connecting to a TV.......................................... 74

Functions Available with Disc Navigation ...... 101

Installing Software ......................................... 134

With this DVD Palmcorder you can view the picture being recorded or the playback picture whether on the

LCD monitor or in the viewfinder. Opening or closing the LCD monitor switches the picture to appear on the

LCD monitor or in the viewfinder. The following text describes the operation assuming that the viewfinder

is used as a major monitor device.

VDR-M30PP_GB.book Page 11 Friday, March 14, 2003 8:53 PM

12

QR34642

Introduction

●You can record even during playback

Unlike tape devices, you do not need to search for the recording start position or locate the beginning of

blank portion.

You can start recording during playback New recording will not overwrite any previously recorded data.

●You can immediately play back desired recorded scenes

You do not need to rewind, unlike recorders using tape.

You can select any scene you want and immediately play it back (using Disc Navigation function).

●Use Disc Navigation to create your original movie

You can delete unnecessary scenes, move any scenes, etc., and create your original movie work (Play List).

●You can easily edit scenes

Using this DVD Palmcorder, you can collect scenes

of your child, for example, on play list of Disc

Navigation function and create an original movie:

Then simply play back the play list and dub it on

V CR . I t i s a l so e as y t o m a ke a n y n um b e r o f id e n ti c al

tapes.

●Create original DVDs on PC

You can use a DVD-R disc to create an original

DVD, using the provided software CD-ROM.

The created DVD disc can be played back on DVD

player, DVD-ROM drive, etc.

If you stop playback midway and start recording, overwrite will not occur.

Recorded scenes

Before editing

After editing

Until now, you had to

repeatedly press

buttons

With DVD, you can simply

play back this DVD

Palmcorder, and press the

record button on VCR.

Original DVD being

created

Playback of DVD

VDR-M30PP_GB.book Page 12 Friday, March 14, 2003 8:53 PM

Quick Start Guide for Software

Features

Following software programs are contained on the provided CD-ROM.

≥Confirming the environment of connecting equipment: see page 134

Installation Guide (See page 134 for details)

1 Installing USB Driver.

≥Be sure not to connect the USB Cable before executing “USBready.exe” on the provided

CD-ROM.

≥After opening the “VDR-M30” drive from “My Computer”, and double-click “USB Ready” icon. “USB

Ready” message will appear, and then connect the USB Cable. Installation automatically starts.

2 Install the software (DVD-RAM Driver, MyDVD and DVD-MovieAlbumSE).

Suggestions for using software (See page 142 for details)

1 Connect this DVD Palmcorder with the recorded DVD-RAM disc inserted to PC using

USB Cable as follows.

2 Edit motion images using DVD-MovieAlbumSE.

≥You can edit images on the DVD-RAM disc.

3 Export motion image data to PC using DVD-MovieAlbumSE.

4 MyDVD will automatically start. (See page 00 for details)

Software Feature

USB Driver Install this driver when using the provided USB Cable to connect this

DVD Palmcorder to PC.

DVD-RAM Driver Install this driver when using stills and images recorded on DVD-RAM

disc on a PC.

DVD-MovieAlbumSE By combining DVD-MovieAlbumSE with the DVD Palmcorder, it is

possible to use playback, recording and editing. It is also possible to

transfer extracted data and title information etc to My DVD.

MyDVD Use this software when creating a DVD-Video disc from motion images

edited using DVD-MovieAlbumSE.

We will add the figure connecting

PC to DVD Palmcorder.

13

5 Edit motion image and interractive DVD menu using MyDVD.

6 Insert the new DVD-R disc into the DVD palmcorder.

≥When making an original DVD-R disc using MyDVD software, a message for initialization appears

on the LCD of DVD Palmcorder. Press “No” and then follow the instructions on the screen of your

PC to make the original DVD-R disc. Do not perform initialization on DVD Palmcoder when using a

DVD-R disc with computer.

7 Write images to the DVD-R Disc with MyDVD.

≥Write edited motion images to an 8 cm DVD-R disc in this DVD Palmcorder using MyDVD

software.

Cautions for use

≥When using a new DVD-R disc in your Palmcorder, you must initialize it before motion images.

DVD-RAM disc and Card do not require initialization.

≥When using MyDVD software on Windows 2000 Professional / XP, log on to your PC as

Administrator or with a login name equally authorized . If you log on with a login name other

than Administrator, you cannot use MyDVD.

≥Set the display resolution to 1024 ~ 768 (16 bits color) when using the DVD-MovieAlbum.

DIsplay Settings method as follows:

Select “Start” >> “Settings” >> “Control Panel” >> “Display” and select “Settings” tab on

“Display”, and then adjust “Screen Resolution” and “Color quality” to the above.

≥DVD-R discs are a write-one format, therefore when you write information to the DVD-R disc

with DVD-MovieAlbum or My DVD, you cannot edit it again.

14

15

QR34642

Table of Contents

Be sure to read the following before opening

the package of CD-ROM.................................. 4

Cautions When Using ......................................... 7

Cautions When Storing..................................... 10

Suggestions and Restrictions ........................... 10

Read This First ................................................. 11

Introduction....................................................... 12

Quick Start Guide for Software......................... 13

Table of Contents ............................................. 15

Checking Provided Accessories ....................... 18

Names of Parts................................................. 19

About This Manual............................................ 23

Discs and Cards ............................................... 24

Available Discs ......................................................24

Information on DVD-R Disc ...................................25

Examples of Discs that Cannot be Used on

this DVD Palmcorder: .........................................25

Handling Discs.......................................................26

Available Cards .....................................................27

Storage Capacity on Disc or Card .................... 28

Recordable Time of Movie (Video) ........................28

Recordable Stills (Photos) .....................................29

Features of DVD Palmcorder............................ 30

Versatile Functions Available ................................30

Recording on Disc .................................................32

Recording Movie and Still......................................32

Immediate Reviewing of Recorded Image.............33

Editing in Various Ways on DVD Palmcorder

Alone ..................................................................33

Using with Various Devices ...................................33

Setups

Setting Up the DVD Palmcorder....................... 34

Attaching adjuster (securing tab)...........................34

Holding DVD Palmcoder........................................34

Attaching Shoulder Belt.........................................35

Attaching Lens Cap ...............................................35

Inserting Battery into Remote Controller ...............36

Removing Battery from Remote Controller............36

Setting Up the Battery Pack.............................. 38

Charging Battery Pack...........................................38

Attaching Battery Pack to DVD Palmcorder ..........39

Removing Battery Pack .........................................39

Battery Remaining Level Indicator.........................41

Efficient Use of Battery Pack .................................41

Using DVD Palmcorder with AC Adapter/Charger 42

Inserting and Removing Disc............................ 43

Inserting Disc.........................................................43

Removing Disc ......................................................45

Inserting and Removing Card ........................... 46

Basic Techniques

Basic Operation of DVD Palmcorder................ 47

Turning DVD Palmcorder On or Off ......................47

Viewing Subject Through Viewfinder.....................48

Viewing Image on LCD Monitor Screen ................48

Closing LCD Monitor .............................................49

Setting Date and Time...................................... 50

Changing Display Format of Date and Time .........51

Recording Movie............................................... 52

Using External Microphone ...................................54

Recording Stills................................................. 55

Zooming............................................................ 57

Macro Recording ...................................................58

Using Conversion Lens (Generally Available).......58

Manually Focusing Subject............................... 59

Focusing During Recording...................................59

Adjusting Exposure Manually ........................... 61

Compensating for Backlight.............................. 62

Using Auto Function ......................................... 63

On-Screen Information ..................................... 64

Information Display During Recording...................64

Recording Images from Other AV Devices....... 67

Connecting to Other AV Device ............................67

Recording Images from AV Device .......................68

Playing Back..................................................... 69

Immediately Checking Recorded Scene ...............69

Playback from Start of Disc or Card......................70

Search Playback of Movie.....................................70

Frame Advance/Frame Back/Slow Playback of

Movie..................................................................70

Skip Playback of Movie .........................................71

Playing Back Stills.................................................71

Jumping to Specified Point (Go To) ......................72

On-Screen Information Display ........................ 73

Information Display during Playback.....................73

Playback on Other Devices .............................. 74

Connecting to a TV................................................74

Viewing on TV Screen...........................................75

Playback on DVD Player .......................................76

Removing and Replacing from/in Round

DVD Holder ........................................................77

How to Remove Disc.............................................77

Replacing Disc in Round DVD Holder...................78

When the Hinge of Round DVD Holder

Comes Off ..........................................................78

Disc Cleaning ........................................................78

Playback on DVD Video Recorder/Player ........ 79

VDR-M30PP_GB.book Page 15 Friday, March 14, 2003 8:53 PM

16

QR34642

Advanced Techniques

Understanding Flow of Menu............................ 80

Setting Up Camera Functions........................... 82

Selecting Shooting Mode to Match the Subject

(Switching Program AE Mode) ...........................82

Adjusting Color (White Balance)............................83

Using the Electronic Image Stabilizer (EIS)...........85

Magnifying Subject Image (Dig. Zoom) .................86

Reducing Wind Noise During Recording

(Wind Cut)...........................................................87

Setting Up Record Functions............................ 88

Switching Movie Quality (VIDEO Mode)................88

Switching Quality of Still Image (Quality)...............89

Receiving Image from Another Device

(Input Source) .....................................................90

Switching External Input Recording Method

(PHOTO Input)....................................................90

Self Timer ..............................................................91

Setting OSD Output On or Off

(On-Screen Display) ...........................................92

LCD Setup ........................................................ 93

Setting Brightness of LCD Screen (Brightness) ....93

Setting Color Density of LCD screen

(Color Level) .......................................................93

Initial Settings ................................................... 94

Switching Operating Sound On or Off (Beep) .......94

Turning DVD Palmcorder Off Automatically

(Power Save)......................................................94

Turning Record LED On or Off (Record LED) .......95

Changing Display Language (Language) ..............95

Resetting Menu Settings to Defaults (Reset) ........96

Disc Navigation

Using Disc Navigation....................................... 97

Starting Disc Navigation ........................................97

Exiting Disc Navigation..........................................99

Playing Back from Disc Navigation Screen ...........99

Selecting Multiple Scenes ...................................100

Selecting Consecutive Scenes Together.............100

Disc Navigation Menu..................................... 101

Functions Available with Disc Navigation ............101

Understanding Flow of Disc Navigation Menu.....102

Scene.............................................................. 103

Deleting Scenes (Delete).....................................103

Changing Images for Thumbnails

(Edit - Thumbnail) .............................................105

Playing Back by Skipping Scenes (Edit - Skip) ...106

Adding Special Effects (Edit - Fade)....................107

Arranging Order of Scenes (Edit - Move) ............108

Combining Multiple Scenes (Edit - Combine)......109

Dividing Movies (Edit - Divide).............................110

Copying Stills on DVD-RAM Disc to Card

(Copy) ...............................................................111

Locking Scenes on Card (Lock) ..........................112

Designating Scenes to be Printed (DPOF)..........113

Selecting Scenes Using Menu Screen (Select)...114

Displaying Information Using Menu Screen

(Detail) ..............................................................115

Program.......................................................... 116

What is “program”?..............................................116

Switching to Thumbnail Display of Specific Date

(Switch) ............................................................116

Playing Back Program (Play) ..............................117

Changing Title of Program (Title) ........................117

Play List.......................................................... 119

What is “Play List”? .............................................119

Creating New Play List (Create)..........................119

Switching to Display of Each Play List (Switch) ..120

Playing Back a Play List (Play)............................121

Adding Scenes to Play List (Editing Play List).....122

Deleting Scenes from Play List

(Editing Play List) .............................................123

Adding Scenes Using Submenu for Editing

(Editing Play List) .............................................123

Deleting Scenes Using Submenu for Editing

(Editing Play List) .............................................124

Selecting Scenes Using Submenu for Editing

(Editing Play List) .............................................124

Arranging Order of Scenes (Move) .....................125

Changing Title of Play List (Title) ........................126

Deleting Play List (Delete)...................................126

Go To.............................................................. 127

Top (End) ............................................................127

Disc or Card Management.............................. 128

Verifying Remaining Free Space on Disc or Card

(Capacity) .........................................................128

Protecting Disc from Writing (Protect Disc) .........128

Initializing DVD-RAM Disc or Card

(Format Disc. format Card)...............................129

Updating Control Information of DVD-RAM Disc.130

Finalizing Disc (DVD-R) ......................................131

Others............................................................. 132

Displaying Movies or Stills Independently

(Category) ........................................................132

Playing Back Scenes Repeatedly (Repeat Play) 132

Slide Show (Continuous Playback of Stills).........133

Installing Software

Compatible PC for use with DVD Camcorder:

VDR M30 ..................................................... 134

Operations will not be guaranteed under the

following conditions...................................... 134

Contents on Provided CD-ROM ..................... 135

Installing USB Driver ...........................................137

Installing DVD-RAM Driver..................................140

Installing DVD-MovieAlbumSE............................142

Installing MyDVD.................................................144

Creating DVD Video on PC from DVD-RAM Disc

Recorded on DVD Palmcorder .................... 145

VDR-M30PP_GB.book Page 16 Friday, March 14, 2003 8:53 PM

17

QR34642

Subsidiary Information

Cleaning.......................................................... 147

No DVD Palmcorder Operation - Check the

Following:..................................................... 148

Error Messages .............................................. 150

Troubleshooting.............................................. 157

System Reset ................................................. 164

Major Specifications........................................ 165

Introduction to Optional Accessories .............. 167

Palmcorder Accessory System............................167

Information on Round DVD Holder......................168

Index............................................................... 169

Request for Service Notice (USA Only).......... 172

Limited Warranty (For USA Customers) ......... 173

Customer Services Directory .......................... 174

Warranty (For Canadian Customers).............. 175

VDR-M30PP_GB.book Page 17 Friday, March 14, 2003 8:53 PM

18

QR34642

Checking Provided Accessories

Make sure that you have all the following accessories in package:

Battery Pack (model CGA-DU14A):

Portable power supply for this DVD

Palmcorder. Charge it before use.

AC Adapter/Charger (model PV-DAC13):

Used to power the DVD Palmcorder from AC

outlet, or charge battery pack.

DC Cord:

When powering the DVD Palmcorder from

household AC outlet, use this cord to connect

the DVD Palmcorder and AC adapter/

charger.

Power Cable:

Connect between household AC outlet and

AC adapter/charger.

Remote Controller (model VEQ3993):

Use to control the DVD Palmcorder from a

distance.

Button Type Battery (model CR2025):

To power the remote controller.

AV/S Input/Output Cable: (EW12432)

Used when viewing the picture played back

on the DVD Palmcorder on TV screen, or

input or output video from/to another video

device.

Shoulder Belt:

Attach to the DVD Palmcorder to hang it from

shoulder.

Lens Cap and Lens Cap String:

Attach the lens cap when not recording, to

protect the lens.

8 cm DVD-RAM Disc (in Round DVD

Holder):

To record video (movie) on this DVD

Palmcorder.

Ferrite Core: (BZ10682)

In order to control radio noise emission,

attach this to external microphone cable if

you are using the external microphone.

Software CD-ROM: (VFF0197)

Use this CD-ROM on PC when connecting

the DVD Palmcorder to PC.

USB Cable: (EW12381)

WARNING: Keep

this battery away

from children. If

swallowed, consult

a physician

immediately for

emergency

treatment.

VDR-M30PP_GB.book Page 18 Friday, March 14, 2003 8:53 PM

19

QR34642

Names of Parts

1 Recording indicator (P. 95)

The red indicator will light during recording.

2 Optical 10× zoom lens (P. 57)

3 Lens hood (P. 58)

Always remove this lens hood when using

generally available tele-conversion or wide-

conversion lens.

4 Infrared receiver (P. 37)

When the remote controller is used to operate

the DVD Palmcorder, this receiver will receive

the infrared signal.

5 Zoom lever (P. 57)

Push the lever to the T side for telephoto, or to

the W side for wide-angle.

6 Accessory shoe

7 External microphone jack (P. 54)

8 AV input/output jack (P. 67, 74)

9 Stereo microphone (P. 54)

10 2.5” type Liquid Crystal Display (LCD)

(inside) (P. 48)

11 BATTERY EJECT switch (P. 39)

The BATTERY EJECT switch is located on the

bottom of this DVD Palmcorder: Slide it when

removing the battery pack.

A/V

MIC

BATTERY EJECT

7

8

11

910

1234 5 6

(Inside the cover)

(Bottom)

VDR-M30PP_GB.book Page 19 Friday, March 14, 2003 8:53 PM

20

QR34642

12 Viewfinder (P. 48)

13 Diopter control (P. 48)

To adjust the focus of image appearing in the

viewfinder. (Pull out the viewfinder.)

14 ACCESS/PC indicator (P. 9, 52, 55)

Will blink or light while the DVD Palmcorder is

operating.

15 DISC EJECT button (P. 43)

Press and release this button to open the disc

guide.

16 CARD ACCESS indicator (P. 9, 55)

17 Card insertion block (P. 46)

18 Battery attachment platform (P. 39)

19 Record button (REC) (P. 52)

20 Shoulder belt attachments portion (P. 35)

21 Power switch (P. 47, 52, 55)

22 Speaker (P. 69)

23 Grip Belt (Free Style Grip Belt) (P. 34)

12 13 14 1715

18 19 21 2322

16

20

VDR-M30PP_GB.book Page 20 Friday, March 14, 2003 8:53 PM

La pagina sta caricando ...

Panasonic VDR-M30PP Manuale utente

Panasonic VDR-M30PP Manuale utente

in altre lingue

Documenti correlati

Altri documenti