ProLights LED Fresnel pole operated FC and Tunable White Manuale utente

Marca: ProLights

Modello: LED Fresnel pole operated FC and Tunable White

Categoria: Stroboscopi

Tipo: Manuale utente

USER MANUAL

MANUALE UTENTE

ECLFR2KPTW

EN - IT

POLE OPERATED FRESNEL PROJECTOR

reproduced in any form or by any means for any commercial use.

In order to improve the quality of products, Music&Lights S.r.l. reserves the right to modify the

characteristics stated in this instruction manual at any time and without prior notice.

All revisions and updates are available in the ‘manuals’ section on site www.musiclights.it

REV.01-04/20

ECLFR2KPTW

Packing content

• ECLFR2KPTW

• ECLFR2KTPG

• ECLFR2KBD

• ECLFRSPG

• Power cable

• User manual

TABLE OF

CONTENTS

Safety

SymbolsSymbols

General instructionsGeneral instructions

ApprovalsApprovals

Fire preventionFire prevention

Electric shock preventionElectric shock prevention

Photobiological safetyPhotobiological safety

WarningsWarnings

Waste Electrical and Electronic Equipment Directive Waste Electrical and Electronic Equipment Directive

(WEEE)(WEEE)

1 Technical drawing

1. 1 Operating elements and connections1. 1 Operating elements and connections

2 Installation

2. 1 Mounting2. 1 Mounting

3 Functions and settings

3. 1 Operation3. 1 Operation

3. 2 Basic3. 2 Basic

3. 3 Menu structure3. 3 Menu structure

3. 4 DMX addressing3. 4 DMX addressing

3. 5 DMX conguration3. 5 DMX conguration

3. 6 Linking3. 6 Linking

3. 7 Screen3. 7 Screen

3. 8 Advanced3. 8 Advanced

3. 9 Information3. 9 Information

3. 10 Master/Slave mode3. 10 Master/Slave mode

3. 11 Eects mode3. 11 Eects mode

3. 12 Fixed color3. 12 Fixed color

3. 13 Manual mode3. 13 Manual mode

3. 14 DMX control3. 14 DMX control

3. 15 Connection of the DMX line3. 15 Connection of the DMX line

3. 16 Construction of the DMX termination3. 16 Construction of the DMX termination

4 Maintenance

4. 1 Maintenance and cleaning the unit4. 1 Maintenance and cleaning the unit

4. 2 Trouble shooting4. 2 Trouble shooting

ECLFR2KPTW

WARNING! Before carrying out any operations with the unit, carefully read this instruction

manual and keep it with cure for future reference. It contains important information about

the installation, usage and maintenance of the unit.

T 45°C

ELECTRIC SHOCK RISK

READ THE USER MANUAL

GENERAL RISK / ATTENTION

DO NOT STARE AT THE OPERATING LIGHT SOURCE

WASTE ELECTRICAL & ELECTRONIC EQUIPMENT

MAX OPERATING AMBIENT TEMPERATURE

INDOOR USE

FIXING POINT FOR SAFETY CABLE

EUROPEAN UNION CONFORMITY

SYMBOLS

ECLFR2KPTW

SAFETY

General instruction

• This unit is not for home use, only professional applications.

• The connection to the main network of electric distribution must be carried out by a qualied electrical

installer.

• Before starting any maintenance work or cleaning the projector, cut o power from the main supply.

• Connection must be made to a power supply system tted with ecient earthing (Class I appliance ac-

cording to standard EN 60598-1). It is, moreover, recommended to protect the supply lines of the units

from indirect contact and/or shorting to earth by using appropriately sized residual current devices.

• Do not modify the unit in any way not described in this manual or install parts other than the original

Music & Lights parts. Do not apply lters, lenses or other materials on lenses or other optical compo-

nents. Use only accessories approved by Music & Lights.

• If this device will be operated in any way dierent to the one described in this manual, it may suer

damage and the guarantee becomes void.

• We decline any liability deriving from improper use of the product.

Approvals

• The products referred to in this manual conform to the European Community Directives LVD (Low Volt-

age Directive) 2014/35 / EC, EMC (Electromagnetic Compatibility Directive) 2014/30 / EU, RoHS (Restric-

tion of Hazardous Substances Directive) 2011/65 / CE and are therefore marked with .

Fire prevention

• The minimum distance between the projector and the surrounding walls and ammable materials

must be greater than 50 cm and the ventilation openings must in no case be blocked.

• Replace a defective, blown or damaged fuse only with one of the same type. To replace the fuse, refer

to the “Maintenance” paragraph.

• Do not use the unit if the ambient temperature exceeds 45 ° C (122 ° F).

• The surface of the appliance can reach up to 50 ° C (158 ° F) during operation. Avoid contact with peo-

ple and materials.

• Make sure there is a free and unobstructed air ow around the appliance.

Electric shock prevention

• The unit is supplied with hazardous network voltage (230V~). Leave servicing to skilled personnel only.

Never make any modications on the unit not described in this instruction manual, otherwise you will

risk an electric shock.

• Disconnect power to the unit when not in use.

• Install the xture in a well ventilated place.

• Refer to any service operation not described in this manual to Music & Lights technical support.

• Isolate the unit immediately from the power supply if any gaskets, covers, cables or other components

are damaged, defective, deformed or showing signs of overheating. Do not reapply power until repairs

are complete. Before using the unit, check that all components and power distribution cables are in

perfect condition.Check that the frequency and voltage of the network correspond to the frequency

and voltage for which the unit is set up, indicated on the electrical data plate.

WARNING! Before carrying out any operations with the unit, carefully read this instruction

manual and keep it with cure for future reference. It contains important information about

the installation, usage and maintenance of the unit.

T 45°C

0,5 m

ECLFR2KPTW

Photobiological safety

• This device is a product identied in risk group 2 according to EN 62471.

• Emits potentially dangerous optical radiation. It falls into the categories of the risk group according to

EN 62471.

• Do not look directly at the LED source during operation. It can be harmful to the eyes.

Warnings

• This device is rated IP20. It is not suitable for use in humid places. Never use the xture in places subject

to vibrations or bumps.

• Make certain that no inammable liquids, water or metal objects enter the xture.

Waste Electrical and Electronic Equipment Directive (WEEE)

• The unit, accessories and packaging should be sorted for environmetal-friendly recycling.

• For EC countries: according to the European Directive 2012/19/EC for Waste Electrical and Electronic

Equipment and its implementation into national right, luminaires that are no longer usable must be

collected separately and disposed of in an environmentally correct manner.

WARNING! Before carrying out any operations with the unit, carefully read this instruction

manual and keep it with cure for future reference. It contains important information about

the installation, usage and maintenance of the unit.

ECLFR2KPTW

- 1 - TECHNICAL DRAWING

Technical drawing Fig.1

ECLFR2KPTW

1.1 OPERATING ELEMENTS AND CONNECTIONS

16 17 1815

12 13 14

Fig.2Rear view

Side view

1. VENTILATION GRID for air ow outlet not to be

obstructed.

2. HANDLE

3. CONTROL PANEL with display and 4 buttons

used to access the control panel functions

and manage them.

4. ZOOM ADJUSTMENT AND FOCUS knob to

zoom the projected image clearly.

5. LENS

6. SPIGOT

7. POLE OPERATED BRACKET

8. GEL FILTER FRAM

9. BARN DOOR with directional aps to adjust

the light beam.

10. MAIN FUSE HOLDER: replace a burnt-out fuse by

one of the same type only

11. POWER IN (PowerCON TRUE IN): for connection to

a socket (100-240V~/50-60Hz) via the supplied

mains cable.

12. DMX IN (5-pole XLR): 1 = ground, 2 = DMX-, 3 =

DMX+, 4 N/C, 5 N/C.

13. DMX OUT (5-pole XLR): 1 = ground, 2 = DMX-, 3 =

DMX+, 4 N/C, 5 N/C.

14. POWER OUT (PowerCON TRUE OUT): power

output for connection of multiple units in series.

15. GUIDE for locking and releasing accessories.

16. YELLOW POLE OPERATOR: Zoom pole operator.

17. WHITE POLE OPERATOR: Tilt pole operator.

18. BLUE POLE OPERATOR: Pan pole operator.

ECLFR2KPTW

Fig.3

- 2 - INSTALLATION

2.1 MOUNTING

ECLFR2KPTW is designed for applications in exhibition areas, commercial spaces, museums, restaurant,

churches, and any other installation where size is an important factor. For xing, stable mounting clips are

required. The mounting place must be of sucient stability and be able to support a weight of 10 times

of the unit’s weight.

When carrying out any installation, always comply scrupulously with all the regulations (particularly re-

garding safety) currently in force in the country in which the xture’s being used.

• Install the projector at a suitable location.

• Always additionally secure the projector with the safety rope from falling down. For this purpose, fas-

ten the safety rope at a suitable position so that the maximum fall of the projector will be 20 cm. The

adjust the projector and use the knobs.

NOTE - For the installation of the ECLFR2KPTW make sure that the ridge of the adaptor is in with the

groove of the track.

ECLFR2KPTW

UP DOWN ENTER

Used to access the menu or

to return a previous menu

option

Navigates downwards through

the menu list and increases

the numeric value when in a

function

Navigates upwards through

the menu list and decreases

the numeric value when in

a function

Used to select and store the

current menu or conrm the

current function value or

option within a menu

Fig.4

Enter

Down

- 3 - FUNCTIONS AND SETTINGS

3.1 OPERATION

To turn ECLFR2KPTW connect the supplied main cable to a socket (100-240 VAC-50/60 Hz). Then the unit

is ready for operation and can be operated via a DMX controller. To switch o, disconnect the mains plug

from the socket. For a more convenient operation it is recommended to connect the unit to a socket which

can be switched on and o via a light switch.

3.2 BASIC

The ECLFR2KPTW has a display and 4 button for access to the control panel functions (g.4).

MODE LEFT KNOB

CENTRAL KNOB RIGHT KNOB

CCT Dimmer (0 - 255) +/- Green (-25-+25) Control temperature

(CT): 2800 K - 10000 K

HSI Dimmer (0 - 255) Colors (0 - 255) Saturation (SAT): 0 - 255

1 CONNECT

DMX Address

Value (001-512)

Default: 1

DMX Mode

1CH

Amber Shift on

Default: 19CH

Color

Temperature

CTO 2800 - 10000K

Hue (025~025)

Color Picker

3200K

100

...

777

Customization

Red (000~255)

Orange (000~255)

Green (000~255)

Royal Blue (000~255)

Blue (000~255)

Lime (000~255)

2CH

Amber Shift on

Color

Temperature

CTO 2800 - 10000K

Hue (025~025)

Color Picker

3200K

100

...

777

Customization

Red (000~255)

Orange (000~255)

Green (000~255)

Royal Blue (000~255)

Blue (000~255)

Lime (000~255)

5CH1

Color Picker

5CH2

7CH1

7CH2

No Action

3200K

100

...

777

8CH

9CH

12CH

13CH

16CH

19CH

21CH

2 SETUP

Screen

Back Light

10 s

20 s

30 s

Default: 10 s

Flip Display

NO-Yes Default: No

Key Lock

NO-Yes Default: No

ECLFR2KPTW

3.3 MENU STRUCTURE

3 ADVANCED

Full On Mode

Studio

Default: Studio

Dimmer Mode

O

Dimmer 1

Dimmer 2

Dimmer 3

Default: O

White Balance

O

Adjust

Red (125~255)

Orange (125~255)

Green (125~255)

Royal Blue (125~255)

Blue (125~255)

Lime (125~255)

Default: O

Led Frequency

600Hz

1200 Hz

2000 Hz

4000 Hz

6000Hz

25kHZ

Default: 1200Hz

Fan Mode

Auto

O

Silent

Default : Auto

Factory Reload

No-Yes No-Yes Default: No

4 INFORMATION

Fixture TIme

0-9999

Version

V1.0

UID

15D00229****

5 STAND ALONE

Master/Slave

Master

Slave

Default : Slave

Eects

Eect1

Eect2

Eect3

Eect4

(1~100) Default: Eect4

Speed=100

CCT

HSI

Color Tempera-

ture

2800K

3000K

3200K

3400K

3600K

3800K

4000K

4200K

4400K

4600K

4800K

5000K

5200K

5400K

5600K

5800K

6000K

6200K

6400K

6800K

7000K

7200K

7400K

7600K

7800K

8000K

8200K

8400K

8600K

8800K

9000K

9200K

9400K

9600K

9800K

10000K

Dimmer (000~255)

Hue (025~025)

Default : 6000K

Dimmer=255

Hue=0

ECLFR2KPTW

Fixed Color

R.0

R.G

R.RB

R.B

R.L

O.G

O.RB

O.B

O.L

G.RB

G.B

G.L

RB.B

RB.L

B.L

R.O.G

R.O.RB

R.O.B

R.O.L

R.G.RB

R.G.B

R.G.L

R.RB.B

R.RB.L

R.B.L

O.G.RB

O.G.B

O.G.L

O.RB.B

O.RB.L

O.B.L

G.RB.B

G.RB.L

G.B.L

RB.B.L

R.O.G.RB

R.O.G.B

R.O.G.L

R.O.RB.B

R.O.RB.L

R.O.B.L

R.G.RB.B

R.G.RB.L

R.G.B.L

R.RB.B.L

O.G.RB.B

O.G.RB.L

O.G.B.L

O.RB.B.L

G.RB.B.L

R.O.G.RB.B

R.O.G.RB.L

R.O.G.B.L

R.O.RB.B.L

R.G.RB.B.L

O.G.RB.B.L

R.O.G.RB.B.L

Dimmer (000~255) Default:

R.O.G.RB.B.L

Dimmer=255

Color Picker

3200K

100

101

102

103

104

105

106

107

110

111

113

115

116

117

118

119

120

121

122

124

126

128

130

132

134

135

136

137

138

139

141

144

147

151

152

156

157

158

161

164

165

166

170

174

179

180

181

182

195

197

198

200

201

202

203

204

205

206

702

730

777

Dimmer (000~255) Default: 3200K

Manual Color

Red

Orange

Green

Royal Blue

Blue

Lime

(000~255) Default:

RGBW=255

ECLFR2KPTW

3.4 DMX ADDRESSING

To set DMX addressing follow the instructions below:

• Press the button MENU to enter the menu mode.

• Press UP/DOWN button to select Connect. Press the ENTER button to conrm.

• Press UP/DOWN button to select DMX Address. Press the ENTER button to conrm.

• Press UP/DOWN button to select the desired value 001-512. Press the ENTER button to conrm.

• Press the MENU button to go back or to meet the waiting time to exit the setup menu.

To able to operate the ECLFR2KPTW with a light controller, adjust the DMX start address for the rst a

DMX channel. If e. g. address 33 on the controller is provided for controlling the function of the rst DMX

channel, adjust the start address 33 on the ECLFR2KPTW. The other functions of the light eect panel are

then automatically assigned to the following addresses.

3.5 DMX CONFIGURATION

The ECLFR2KPTW has dierent DMX channels congurations available selectable through the control

panel.

• Press the button MENU to enter the menu mode.

• Press UP/DOWN button to select Connect. Press the ENTER button to conrm.

• Press UP/DOWN button to select DMX mode. Then press the ENTER button to conrm.

• Press UP/DOWN button to select the desired conguration (1CH, 2CH 2, 5CH1, 5CH2, 7CH1, 7CH2, 8CH , 12CH ,

13CH, 16CH, 19CH, 21CH); then press the ENTER button to save.

• Press the MENU button to go back or to meet the waiting time to exit the setup menu.

The tables on page 15, 16, 17, 18, 19, 20, 21 indicate the operating mode and DMX value. The ECLFR2KPTW

is equipped with 5-pole XLR connections.

3.6 LINKING

Several units may be interconnected; follow the instructions below:

1. Connect the DMX OUT of the master unit via 5-pole XLR cable to the DMX IN of the rst slave unit.

2. Connect the DMX OUT of the rst slave unit to the DMX IN of the second slave unit, etc. until all units

are connected in a chain.

Use standard DMX cables to daisy chain your units together via the DMX connector on the rear of the

units. For longer cable runs we suggest a terminator at the last xture (see page 22).

. . . . . . . . . . . .

DMX Address: 33 DMX Address: 48DMX Address: 38 DMX Address: 43

Fig.5 - Example 5 DMX channels conguration

. . . . . . . . . . . .

DMX512 Controller

ECLFR2KPTW

Numero

canali DMX

Indirizzo di

start (esempio)

Indirizzo DMX

occupati

Prossimo indirizzo di start

possibile per unità n°1

Prossimo indirizzo di start

possibile per unità n°2

Prossimo indirizzo di start

possibile per unità n°3

1 33 33 34 35 36

2 33 33-34 35 37 39

5 33 33 - 37 38 43 48

7 33 33 - 39 40 47 54

8 33 33 - 40 41 49 57

9 33 33 - 41 42 51 60

12 33 33 - 44 45 57 69

13 33 33 - 45 46 59 72

16 33 33 - 48 49 65 81

19 33 33 - 51 52 71 90

21 33 33 - 53 54 75 96

3.7 SCREEN

It is possible to modify the following parameters, related to the display, following the same procedure:

• Press the button MENU to enter the menu mode.

• Press UP/DOWN button to scroll through the menu, select Set Up, then press the ENTER button to access

the next menu.

• Press UP/DOWN button to select Screen and press the ENTER button to proceed.

• Select the proposed option and press the ENTER button to conrm.

- Backlight - Auto O display backlight. This function allows you to switch o automatically the back-

lighting of the display after a certain time which can be set using the directional keys. To have the

display always on select On or set a value between those shown (10s, 20s, 30s) to turn o the display

once the chosen time has elapsed, after exiting the menu.

- Flip Display - Display orientation. This feature allows you to rotate the display by 180 ° to get a better

view of the display when the unit is hanging upside down. Select Yes to activate the function, No to

deactivate it.

- Key lock - With this function, you can lock the keys on the control panel to prevent, for example, tam-

pering with the settings. If this function is activated, the keys are locked automatically. To disable or

temporarily disable or disable the key lock function, press the keys in the following order to regain

access to the menu commands: UP, DOWN, UP, DOWN, ENTER. Select Yes to activate the function or

No to deactivate it.

• Press the ENTER button to conrm the selection.

• Press the MENU button to go back or to meet the waiting time to exit the setup menu.

3.8 ADVANCED

You can change the parameters for the device by following these steps:

• Press the button MENU to enter the menu mode.

• Press UP/DOWN button to select the Advanced. Press the ENTER button to conrm.

• Press UP/DOWN button to select the desired option and press the ENTER button to conrm:

- Full On Mode - Select the Full on Mode function to set the HB mode (High Brightness Mode, with the

ECLFR2KPTW

maxinum value of the colors) or Studio mode with a automatic white balance.

- Dimmer Mode - Adjusting the dimmer. Enter in Dimmer Mode to select specic dimming curve.

Particularly when set:

• O: The increase in light intensity is linear.

• Dimmer 1: dimmer curve with low fade.

• Dimmer 2: dimmer curve with medium fade.

• Dimmer 3: dimmer curve with high fade.

- White Balance - To balance the white on each color. Select the color (Red, Orange, Green, Royal Blue, Blue

and Lime) and the value (125-255) using the UP / DOWN button and press the ENTER button to conrm.

- LED Frequency - To adjust the frequency of the LEDs. Select the frequency 600 Hz - 25 KHz using the UP /

DOWN button and press ENTER to conrm the selection.

- Fan Mode - Fan Speed. Select the fan speed (Auto, On, O, Silent) using the UP / DOWN button.

- Factory Reload - To reset the unit. Select Yes or No and select the UP / DOWN button to conrm.

• Press the MENU button to go back or to meet the waiting time to exit the setup menu.

3.9 INFORMATION

To view all the information on the device, proceed as follows:

• Press the button MENU to enter the menu mode.

• Press UP/DOWN button to select Information, then press the ENTER button to access the next menu.

• Press UP/DOWN button to scroll through the menu, then select one of the following informationa and

press the ENTER button to display it.

- Fixture Time - To view the operating time of the projector.

- Software Version - To view the rmware version will show on the display.

- UID - To view the identication ID for the RDM control.

• Press the MENU button to go back or to meet the waiting time to exit the setup menu.

3.10 MASTER/SLAVE MODE

This mode will allow you to link up the units together without a controller. Choose a unit to function as the

Master. The unit must be the rst unit in line; other units will work as slave.

• Press the button MENU so many times until the display shows Stand Alone, then press the ENTER button

to select Master/Slave.

• Press UP/DOWN button to select the desired mode and then press ENTER to conrm.

• Press the MENU button to go back or to meet the waiting time to exit the setup menu.

• Use standard DMX cables to daisy chain your units together via the DMX connector on the rear of the

units. For longer cable runs we suggest a terminator at the last xture (see page 13).

• Set the slaves to the same DMX modes.

NOTE: the unit, set in Static or Eect mode, always appears to be Master.

3.11 EFFECTS MODE

This xture has a built-in automatic program. To access this, please see the below instructions:

• To enter the Eects mode, press the ENTER button to access the menu.

• Press UP/DOWN button to select Stand Alone, then select Eect. Press ENTER to conrm

• Press UP/DOWN button to select the desired program Eect 1, Eect 2, Eect 3, Eect 4, then press ENTER

to conrm.

• Set the value (1 - 100), then press the ENTER button to conrm.

NOTE: after selecting the described mode, the unit will be Master.

ECLFR2KPTW

3.12 FIXED COLORS

This xture has the ability to accept custom static color settings. Access these chases via the control panel

on the back of the xture.

• Press the MENU button so many times until the display shows Stand Alone, then press the ENTER button.

• Using UP/DOWN button select Static, then press ENTER.

• Select Fixed Color through the UP/DOWN buttons, then press the ENTER button.

• Set the colors R , O, G, W, RB, B, L, R.O.G.RB.B.L through the UP/DOWN buttons, then press the ENTER button.

• Press the MENU button to go back or to meet the waiting time to exit the setup menu.

NOTE: after selecting the described mode, the unit will be Master.

3.13 MANUAL MODE

This mode allows to combine the colors (Red, Orange, Green, Royal Blue, Blue and Lime).

• Press the MENU button so many times until the display shows Stand Alone, then press the ENTER button..

• Select Manual Color through the UP/DOWN buttons, then press the ENTER button.

• Select the color Red, Orange, Green, Royal Blue, Blue and Lime through the UP/DOWN buttons, then press the

ENTER button.

• Using UP/DOWN buttons, select the desired color value 000 - 255.

• Press the ENTER button to continue to the next color Red, Orange, Green, Royal Blue, Blue and Lime.

• Continue until the desired mix is obtained.

• Press the MENU button to go back or to meet the waiting time to exit the setup menu.

NOTE: after selecting the described mode, the unit will be Master.

NOTE: If the projector is in Blackout mode before to receive DMX signal, and if the DMX signal is lost, the

projector will remain on according to the last received DMX value. If the projector was in STATIC or AUTO

mode before to receive DMX signal, if the DMX signal is lost, the projector will return to the previously set

STATIC or AUTO

1 CHANNEL

MODE

FUNCTION DMX

Value

1 Ch

DIMMER

0~100% 000 - 255

2 CHANNELS

MODE

FUNCTION DMX

Value

2 Ch

DIMMER

0~100% 000 - 255

DIMMER SPEED MODE

Preset dimmer speed from display menu

Dimmer speed mode o

Dimmer speed mode1 (fast speed)

Dimmer speed mode2 (middle speed)

Dimmer speed mode3 (slow speed)

000 - 051

052 - 101

102 - 152

153 - 203

204 - 255

5 CHANNELS 1

MODE

FUNCTION DMX

Value

5 Ch1

DIMMER

0~100% 000 - 255

CTO

2800K - 3000K

3000K - 3200K

3200K - 3400K

3400K - 3600K

3600K - 3800K

3800K - 4000K

4000K - 4200K

4200K - 4400K

4400K - 4600K

4600K - 4800K

4800K - 5000K

5000K - 5200K

5200K - 5400K

5400K - 5600K

5600K - 5800K

5800K - 6000K

6000K - 6200K

6200K - 6400K

6400K - 6600K

6600K - 6800K

6800K - 7000K

7000K - 7200K

7200K - 7400K

7400K - 7600K

7600K - 7800K

7800K - 8000K

8000K - 8200K

8200K - 8400K

8400K - 8600K

8600K - 8800K

8800K - 9000K

9000K - 9200K

9200K - 9400K

9400K - 9600K

9600K - 9800K

9800K - 10000K

000 - 007

007 - 014

014 - 021

021 - 028

028 - 035

035 - 042

042 - 049

049 - 056

056 - 063

063 - 070

070 - 077

077 - 084

084 - 091

091 - 098

098 - 105

105 - 112

112 - 119

119 - 126

126 - 133

133 - 140

140 - 147

147 - 154

154 - 161

161 - 168

168 - 175

175 - 182

182 - 189

189 - 196

196 - 203

203 - 210

210 - 217

217 - 224

224 - 231

231 - 238

238 - 245

245 - 255

HUE

-25°~25°

000 - 000

001 - 255

COLOR MACRO

No Function

Amber Shift on

Color Macro

000 - 002

003 - 005

006 - 255

DIMMER SPEED MODE

Preset dimmer speed from display menu

Dimmer speed mode o

Dimmer speed mode1 (fast speed)

Dimmer speed mode2 (middle speed)

Dimmer speed mode3 (slow speed)

000 - 051

052 - 101

102 - 152

153 - 203

204 - 255

ECLFR2KPTW

3.14 CHANNELS DMX

5 CHANNELS 2

MODE

FUNCTION DMX

Value

5 Ch2

DIMMER

0~100% 000 - 255

DIMMER FINE

0~100% 000 - 255

CTO

2800K - 3000K

3000K - 3200K

3200K - 3400K

3400K - 3600K

3600K - 3800K

3800K - 4000K

4000K - 4200K

4200K - 4400K

4400K - 4600K

4600K - 4800K

4800K - 5000K

5000K - 5200K

5200K - 5400K

5400K - 5600K

5600K - 5800K

5800K - 6000K

6000K - 6200K

6200K - 6400K

6400K - 6600K

6600K - 6800K

6800K - 7000K

7000K - 7200K

7200K - 7400K

7400K - 7600K

7600K - 7800K

7800K - 8000K

8000K - 8200K

8200K - 8400K

8400K - 8600K

8600K - 8800K

8800K - 9000K

9000K - 9200K

9200K - 9400K

9400K - 9600K

9600K - 9800K

9800K - 10000K

000 - 007

007 - 014

014 - 021

021 - 028

028 - 035

035 - 042

042 - 049

049 - 056

056 - 063

063 - 070

070 - 077

077 - 084

084 - 091

091 - 098

098 - 105

105 - 112

112 - 119

119 - 126

126 - 133

133 - 140

140 - 147

147 - 154

154 - 161

161 - 168

168 - 175

175 - 182

182 - 189

189 - 196

196 - 203

203 - 210

210 - 217

217 - 224

224 - 231

231 - 238

238 - 245

245 - 255

COLOR MACRO

No Function

Amber Shift on

Color Macro

000 - 002

003 - 005

006 - 255

DIMMER SPEED MODE

Preset dimmer speed from display menu

Dimmer speed mode o

Dimmer speed mode1 (fast speed)

Dimmer speed mode2 (middle speed)

Dimmer speed mode3 (slow speed)

000 - 051

052 - 101

102 - 152

153 - 203

204 - 255

7 CHANNELS 1

MODE

FUNCTION DMX

Value

7 Ch1

RED

0~100% 000 - 255

ORANGE

0~100% 000 - 255

GREEN

0~100% 000 - 255

ROYAL BLUE

0~100% 000 - 255

BLUE

0~100%

000 - 255

LIME

0~100% 000 - 255

DIMMER SPEED MODE

Preset dimmer speed from display menu

Dimmer speed mode o

Dimmer speed mode1 (fast speed)

Dimmer speed mode2 (middle speed)

Dimmer speed mode3 (slow speed)

000 - 051

052 - 101

102 - 152

153 - 203

204 - 255

7 CHANNELS 2

MODE

FUNCTION DMX

Value

7 Ch2

DIMMER

0~100% 000 - 255

RED

0~100% 000 - 255

ORANGE

0~100% 000 - 255

GREEN

0~100% 000 - 255

ROYAL BLUE

0~100% 000 - 255

BLUE

0~100%

000 - 255

LIME

0~100% 000 - 255

ECLFR2KPTW

8 CHANNELS

MODE

FUNCTION DMX

Value

8 Ch

COLOR PICKER

No Funciton

3200K

100

101

102

103

104

105

106

107

110

111

113

115

116

117

118

119

120

121

122

124

126

128

130

132

134

135

136

137

138

139

141

144

147

151

152

156

157

158

161

164

165

166

170

174

179

180

181

182

195

197

000 - 000

001 - 003

004 - 007

008 - 011

012 - 015

016 - 019

020 - 023

024 - 027

028 - 031

032 - 035

036 - 039

040 - 043

044 - 047

048 - 051

052 - 055

056 - 059

060 - 063

064 - 067

068 - 071

072 - 075

076 - 079

080 - 083

084-087

088 - 091

092 - 095

096-099

100 - 103

104 - 107

108 - 111

112 - 115

116 - 119

120 - 123

124 - 127

128 - 131

132 - 135

136 - 139

140 - 143

144 - 147

148 - 151

152 - 155

156 - 159

160 - 163

164 - 167

168 - 171

172 - 175

176 - 179

180 - 183

184 - 187

188 - 191

192 - 195

196 - 199

200 - 203

204 - 207

208 - 211

8 CHANNELS

MODE

FUNCTION DMX

Value

8 Ch

198

200

201

202

203

204

205

206

702

730

777

212 - 215

216 - 219

220 - 223

224 - 227

228 - 231

232 - 235

236 - 239

240 - 243

244 - 247

248 - 251

252 - 255

DIMMER

0~100% 000 - 255

RED

0~100% 000 - 255

ORANGE

0~100% 000 - 255

GREEN

0~100% 000 - 255

ROYAL BLUE

0~100% 000 - 255

BLUE

0~100%

000 - 255

LIME

0~100% 000 - 255

ECLFR2KPTW

La pagina sta caricando ...

ProLights LED Fresnel pole operated FC and Tunable White Manuale utente

Marca: ProLights

Modello: LED Fresnel pole operated FC and Tunable White

Categoria: Stroboscopi

Tipo: Manuale utente

Scarica il pdf

rapporto

ProLights LED Fresnel pole operated FC and Tunable White Manuale utente

ProLights LED Fresnel pole operated FC and Tunable White Manuale utente

Documenti correlati

Altri documenti