ProLights ECLFRJPTW Manuale utente

ECLFRJPTW

POLE OPERATED FRESNEL PROJECTOR

USER MANUAL

MANUALE UTENTE

EN - IT

reproduced in any form or by any means for any commercial use.

In order to improve the quality of products, Music&Lights S.r.l. reserves the right to modify the

characteristics stated in this instruction manual at any time and without prior notice.

All revisions and updates are available in the ‘manuals’ section on site www.musiclights.it

REV.01-04/20

1

ECLFRJPTW

Packing content

• ECLFRJPTW

• ECLIPSEFRSJBD

• ECLFRSPG

• Power cable

• User manual

TABLE OF CONTENTS

Safety

SymbolsSymbols

General instructionsGeneral instructions

ApprovalsApprovals

Fire preventionFire prevention

Electric shock preventionElectric shock prevention

Photobiological safetyPhotobiological safety

WarningsWarnings

Waste Electrical and Electronic Equipment Directive Waste Electrical and Electronic Equipment Directive

(WEEE)(WEEE)

1 Introduction

1. 1 Description and specications1. 1 Description and specications

1. 2 Technical specication1. 2 Technical specication

1. 3 Operating elements and connections1. 3 Operating elements and connections

1. 4 ECLFRSJBP41. 4 ECLFRSJBP4

1. 5 operating elements and connections1. 5 operating elements and connections

2 Installation

2. 1 Mounting2. 1 Mounting

3 Functions and settings

3. 1 Operation3. 1 Operation

3. 2 Basic3. 2 Basic

3. 3 Menu structure3. 3 Menu structure

3. 4 DMX mode3. 4 DMX mode

3. 5 DMX conguration3. 5 DMX conguration

3. 6 Linking3. 6 Linking

3. 7 Screen3. 7 Screen

3. 8 Advanced3. 8 Advanced

3. 9 Information3. 9 Information

3. 10 Master/Slave3. 10 Master/Slave

3. 11 Eects3. 11 Eects

3. 12 Static mode3. 12 Static mode

3. 13 Manual mode3. 13 Manual mode

3. 14 Connection of the DMX line3. 14 Connection of the DMX line

3. 15 Construction of the DMX termination3. 15 Construction of the DMX termination

3. 16 Channels DMX3. 16 Channels DMX

4 Maintenance

4. 1 Maintenance and cleaning the unit4. 1 Maintenance and cleaning the unit

4. 2 Fuse replacement4. 2 Fuse replacement

4. 3 Trouble shooting4. 3 Trouble shooting

2

3

4

5

7

8

10

11

12

15

16

17

18

19

20

27

28

ECLFRJPTW

2

WARNING! Before carrying out any operations with the unit, carefully read this instruction

manual and keep it with cure for future reference. It contains important information about

the installation, usage and maintenance of the unit.

T 45°C

a

ELECTRIC SHOCK RISK

READ THE USER MANUAL

GENERAL RISK / ATTENTION

DO NOT STARE AT THE OPERATING LIGHT SOURCE

WASTE ELECTRICAL & ELECTRONIC EQUIPMENT

MAX OPERATING AMBIENT TEMPERATURE

INDOOR USE

FIXING POINT FOR SAFETY CABLE

EUROPEAN UNION CONFORMITY

SYMBOLS

3

ECLFRJPTW

SAFETY

General instruction

• This unit is not for home use, only professional applications.

• The connection to the main network of electric distribution must be carried out by a qualied electrical

installer.

• Before starting any maintenance work or cleaning the projector, cut o power from the main supply.

• Connection must be made to a power supply system tted with ecient earthing (Class I appliance ac-

cording to standard EN 60598-1). It is, moreover, recommended to protect the supply lines of the units

from indirect contact and/or shorting to earth by using appropriately sized residual current devices.

• Do not modify the unit in any way not described in this manual or install parts other than the original

Music & Lights parts. Do not apply lters, lenses or other materials on lenses or other optical compo-

nents. Use only accessories approved by Music & Lights.

• If this device will be operated in any way dierent to the one described in this manual, it may suer

damage and the guarantee becomes void.

• We decline any liability deriving from improper use of the product.

Approvals

• The products referred to in this manual conform to the European Community Directives LVD (Low Volt-

age Directive) 2014/35 / EC, EMC (Electromagnetic Compatibility Directive) 2014/30 / EU, RoHS (Restric-

tion of Hazardous Substances Directive) 2011/65 / CE and are therefore marked with

.

Fire prevention

• The minimum distance between the projector and the surrounding walls and ammable materials

must be greater than 50 cm and the ventilation openings must in no case be blocked.

• Replace a defective, blown or damaged fuse only with one of the same type. To replace the fuse, refer

to the “Maintenance” paragraph.

• Do not use the unit if the ambient temperature exceeds 45 ° C (122 ° F).

• The surface of the appliance can reach up to 50 ° C (158 ° F) during operation. Avoid contact with peo-

ple and materials.

• Make sure there is a free and unobstructed air ow around the appliance.

Electric shock prevention

• The unit is supplied with hazardous network voltage (230V~). Leave servicing to skilled personnel only.

Never make any modications on the unit not described in this instruction manual, otherwise you will

risk an electric shock.

• Disconnect power to the unit when not in use.

• Install the xture in a well ventilated place.

• Refer to any service operation not described in this manual to Music & Lights technical support.

• Isolate the unit immediately from the power supply if any gaskets, covers, cables or other components

are damaged, defective, deformed or showing signs of overheating. Do not reapply power until repairs

are complete. Before using the unit, check that all components and power distribution cables are in

perfect condition.Check that the frequency and voltage of the network correspond to the frequency

and voltage for which the unit is set up, indicated on the electrical data plate.

T 45°C

a

0,5 m

WARNING! Before carrying out any operations with the unit, carefully read this instruction

manual and keep it with cure for future reference. It contains important information about

the installation, usage and maintenance of the unit.

ECLFRJPTW

4

Photobiological safety

• This device is a product identied in risk group 2 according to EN 62471.

• Emits potentially dangerous optical radiation. It falls into the categories of the risk group according to

EN 62471.

• Do not look directly at the LED source during operation. It can be harmful to the eyes.

Warnings

• This device is rated IP20. It is not suitable for use in humid places. Never use the xture in places subject

to vibrations or bumps.

• Make certain that no inammable liquids, water or metal objects enter the xture.

Waste Electrical and Electronic Equipment Directive (WEEE)

• The unit, accessories and packaging should be sorted for environmetal-friendly recycling.

• For EC countries: according to the European Directive 2012/19/EC for Waste Electrical and Electronic

Equipment and its implementation into national right, luminaires that are no longer usable must be

collected separately and disposed of in an environmentally correct manner.

WARNING! Before carrying out any operations with the unit, carefully read this instruction

manual and keep it with cure for future reference. It contains important information about

the installation, usage and maintenance of the unit.

5

ECLFRJPTW

- 1 - INTRODUCTION

1.1 DESCRIPTION

ECLFRJPTW is an advanced LED replacement of traditional 650 W Fresnel lamps, fea-

turing 6 colour mixing delivering high precision reproduction of the white spec-

trum from 2.800 K to 10.000 K with high CRI and an extensive colour reproduction.

The optical system harnesses the power of a 130 W custom LED with 6 col-

ours to create an even projection, beautiful colours and precise white, with add-

ed ability to apply +/- green and magenta correction to match other sources of light.

Featuring HD dimming and tuning from 2.800 K to 10.000 K version with external battery capabilities, the

ECLIPSEFRESNELTW delivers the performance and quality of output demanded from this level of lumi-

naire.

1.2 TECHNICAL DESCRIPTION

LIGHT SOURCE

• Source:130 W 6 colour custom LEDs source (red, orange, cyan, royal blue, green, lime)

• CCT:2.800 K - 10.000 K

• CRI:> 90

• R9:> 90

• Luminous ux:(15°) 1’637 lm - (51°) 2’700 lm

• Lux:(15°) 2’067 lx @3 m

• Lux:(51°) 421 lx @3 m

• Source life expectancy: > 50.000 h

OPTICS

• Zoom:15 ° - 51 ° manual

• Field angle:26,7° - 75,6° °

• Lens diameter:6’’ - 150 mm

• Lens type:fresnel zoom lens

COLOUR SYSTEM

• Colour mixing: tunable white + colour

• CTC: CTC control through dedicated DMX channel, + / - green and magenta correction and amber shift

activation by DMX

• White presets:2.800 K - 10.000 K

• Colour wheel: virtual colour wheel with presets

• Macros: several pre-build macros with adjustable speed

DYNAMIC EFFECTS

• Static colour mode: selection of static colour

• Manual colour mode: manual adjustment of intensity, CT, colour correction from knob

• Auto mode: built-in programs with execution speed adjustment

• Special features:linear crossfade from a white to any color and CTO applied on colours

BODY

• Hardware on-board:included lter frame, 8 doors barndoor, omega bracket spigot

• Pan angle:360 ° with manual regulation

• Tilt angle:340 ° with manual regulation

• Body: sturdy die-cast aluminium body conceived for long-time durability

• Body colour: black

ECLFRJPTW

6

CONTROL

• Protocols: DMX512, RDM, local knob

• DMX channels:1 / 2 / 5 - 1 / 5 - 2 / 7 / 9 / 12 / 13 / 16 / 19 / 21 channel

• RDM: RDM ready for xture remote monitor and settings

• Display: black OLED high resolution display

• Firmware upgrade: yes, via USB - DMX interface (UPBOX1) not included

• Other: 16bit control of dimmer and colour

ELECTRONICS

• Dimmer: linear 0 ~ 100% electronic dimmer

• Dimmer curves:4 dierent dimming curves available

• Strobe / shutter:1 - 30 Hz, electronic

• Flicker: icker free frequency with adjustable PWM

• Selectable PWM: 600 ~ 25.000 Hz

ELECTRICAL

• Power supply: 100-240 V – 50/60 Hz

• Power consumption (at 230 V):107 W

• Power consumption (at 120 V):111 W

• Output (at 230 V):23 units on a single power line

• Output (at 120 V):12 units on a single power line

• Power factor:pF 0,99 @120 V - pF 0,95 @230 V

BATTERY

• Battery:24 - 34 V 4400 mAh (optional) external battery

• Re-charge connection: XLR 4p

PHYSICAL

• Cooling: combination of heat pipe cooling system and low noise fan

• Sospension and xing: hanging bracket suitable for safe hanging and positioning

• Signal connection: Amphenol XLR 5p IN/OUT connectors

• Power connection: Neutrik powerCON TRUE1 IN/OUT connectors

• IP rating:20

• Dimensions (WxHxD):297x497x260 mm

• Weight: 7.6 kg

Technical drawing Fig.1

7

ECLFRJPTW

1.3 OPERATING ELEMENTS AND CONNECTIONS

Fig.2

5

6

7

3

4

2

1

13

10

9

14

15

16

17

8

11

12

1. VENTILATION GRID for air ow outlet not to be

obstructed.

2. CONTROL PANEL with display and 3 buttons

used to access the control panel functions

and manage them.

3. ZOOM ADJUSTMENT AND FOCUS knob to

zoom the projected image clearly.

4. LENS

5. SPIGOT

6. POLE OPERATED BRACKET

7. GUIDE for locking and releasing accessories.

8. HANDLE

9. YELLOW POLE OPERATOR: Zoom pole

operator.

10. WHITE POLE OPERATOR: Tilt pole operator.

11. BLUE POLE OPERATOR: Pan pole operator.

12. MAIN FUSE HOLDER: replace a burnt-out fuse

by one of the same type only

13. BATTERY 4pin-in.

14. POWER IN (PowerCON IN): for connection to

a socket (100-240V~/50-60Hz) via the sup-

plied mains cable.

15. DMX IN (5-pole XLR): 1 = ground, 2 = DMX-, 3

= DMX+, 4 N/C, 5 N/C.

16. DMX OUT (5-pole XLR): 1 = ground, 2 = DMX-,

3 = DMX+, 4 N/C, 5 N/C.

17. POWER OUT (PowerCON OUT): power output

for connection of multiple units in series.

ECLFRJPTW

8

Fig.4

1

3

8

5

4

7

4

3

2

10

9

6

442

175

368

Fig.3

1.4 ECLFRSJBP4

Battery pack kit for EclipseFresnelJ series, composed by ABS case, 4 pcs battery, 1 pc charger, 4 pcs male-

male cable and 4 pcs male-female cables.

BATTERY TECHNICAL SPECIFICATIONS

• Estimated battery life in single colour mode up to: (R) 8 h - (G) 8 h - (B) 7 h - (L) 3 h - (O) 4 h - (RB) 7h

• Estimated battery life in full-mode up to: (TW) 1,25 h - (TU, DY) 1,5h

• Re-charge time: 5h/max

1.5 OPERATING ELEMENTS AND CONNECTIONS

1. ABS case

2. CHARGER

3. CHARGER OUT

4. Button to start charging

5. MAIN FUSE HOLDER: replace a burnt-out

fuse by one of the same type only

6. POWER IN (PowerCON IN): for connection to

a socket (100-240V~/50-60Hz) via the supplied

mains cable.

7. SWITCH

8. Charger status LED: if it is red, the battery is

charging, if it is green, the battery is charged.

9. BATTERY

10. Battery status LED

9

ECLFRJPTW

Fig.5

Fig.6

MOUNTING

Holes

DMX cable male-female

DMX cable male-male

CORRECT WRONG

IMPORTANT: do not connect this charger directly to the ECLIPSEFESNELJ, please connect this charger only

with the battery as power charger.

Fig.7

ECLFRJPTW

10

- 2 - INSTALLATION

2.1 MOUNTING

ECLFRJPTW may be set up on a solid and even surface. The unit can also be mounted upside down to a

cross arm. For xing, stable mounting clips are required. The mounting place must be of sucient stability

and be able to support a weight of 10 times of the unit’s weight.

When carrying out any installation, always comply scrupulously with all the regulations (particularly re-

garding safety) currently in force in the country in which the xture’s being used.

• Install the projector at a suitable location by means of the mounting bracket.

• Always additionally secure the projector with the safety rope from falling down. For this purpose, fas-

ten the safety rope at a suitable position so that the maximum fall of the projector will be 20 cm.

• Adjust the projector and use the knob to slightly release or tighten the locking mechanism of the

bracket if is necessary.

11

ECLFRJPTW

- 3 - FUNCTIONS AND SETTINGS

3.1 OPERATION

Connect the supplied main cable to a socket (100-240 VAC-50/60 Hz). Then the unit is ready for operation

and can be operated via a DMX controller or it independently performs its show program in succession.

To switch o, disconnect the mains plug from the socket. For a more convenient operation it is recom-

mended to connect the unit to a socket which can be switched on and o via a light switch.

3.2 BASIC

Access control panel functions using the four panel buttons located directly underneath the LED Display

(g.8).

MENU

UP DOWN ENTER

Used to access the menu or

to return a previous menu

option

Navigates downwards through

the menu list and increases

the numeric value when in a

function

Navigates upwards through

the menu list and decreases

the numeric value when in

a function

Used to select and store the

current menu or conrm the

current function value or

option within a menu

Fig.8- Functions of the buttons

MENU

1 CONNECT

ð

DMX Address

ð

Value (001-512) Default: 001

DMX Mode

ð

1CH

ð

Amber Shift on

Default: 19CH

Color

Temperature

ð

CTO 2800 - 10000K

Hue (025~025)

Default: 2800K

Color Picker

ð

3200K

71

97

100

...

777

Default: 3200K

Customization

ð

Red (000~255)

Orange (000~255)

Green (000~255)

Royal Blue (000~255)

Blue (000~255)

Lime (000~255)

Default: 255

2CH

ð

Amber Shift on

Color

Temperature

ð

CTO 2800 - 10000K

Hue (025~025)

Default: 2800K

Color Picker

ð

3200K

71

97

100

...

777

Default: 3200K

Customization

ð

Red (000~255)

Orange (000~255)

Green (000~255)

Royal Blue (000~255)

Blue (000~255)

Lime (000~255)

Default: 255

5CH1

5CH2

7CH1

7CH2

ð

Color Picker

ð

No Action

3200K

71

97

100

...

777

8CH

9CH

12CH

13CH

16CH

19CH

21CH

2 SETUP

ð

Screen

ð

Back Light

ð

On

10 s

20 s

30 s

Default: 10 s

Flip Display

ð

No-Yes Default: No

Key Lock

ð

No-Yes Default: No

ECLFRJPTW

12

3.3 MENU STRUCTURE

3 ADVANCED

ð

Full On Mode

ð

HB

Studio

Default: Studio

Dimmer Mode

ð

O

Dimmer 1

Dimmer 2

Dimmer 3

Default: O

White Balance

ð

O

Adjust

ð

Red (125~255)

Orange (125~255)

Green (125~255)

Royal Blue (125~255)

Blue (125~255)

Lime (125~255)

Default: O

Led Frequency

ð

600Hz

1200 Hz

2000 Hz

4000 Hz

6000Hz

25kHZ

Default: 1200Hz

Fan Mode

ð

Auto

On

O

Silent

Default : Auto

Factory Reload

ð

No-Yes No-Yes Default: No

4 INFORMATION

ð

Fixture TIme

ð

0-9999

Version

ð

V1.0

UID

ð

15D0021F****

5 STAND ALONE

ð

Master/Slave

ð

Master

Slave

Default : Slave

Eects

ð

Eect1

Eect2

Eect3

Eect4

ð

(1~100) Default: Eect4

Speed=100

CCT

HSI

Color Tempera-

ture

ð

2800K

3000K

3200K

3400K

3600K

3800K

4000K

4200K

4400K

4600K

4800K

5000K

5200K

5400K

5600K

5800K

6000K

6200K

6400K

6600K

6800K

7000K

7200K

7400K

7600K

7800K

8000K

8200K

8400K

8600K

8800K

9000K

9200K

9400K

9600K

9800K

10000K

ð

Dimmer (000~255)

Hue (025~025)

Default : 6000K

Dimmer=255

Hue=0

13

ECLFRJPTW

Fixed Color

ð

R

O

G

RB

B

L

R.0

R.G

R.RB

R.B

R.L

O.G

O.RB

O.B

O.L

G.RB

G.B

G.L

RB.B

RB.L

B.L

R.O.G

R.O.RB

R.O.B

R.O.L

R.G.RB

R.G.B

R.G.L

R.RB.B

R.RB.L

R.B.L

O.G.RB

O.G.B

O.G.L

O.RB.B

O.RB.L

O.B.L

G.RB.B

G.RB.L

G.B.L

RB.B.L

R.O.G.RB

R.O.G.B

R.O.G.L

R.O.RB.B

R.O.RB.L

R.O.B.L

R.G.RB.B

R.G.RB.L

R.G.B.L

R.RB.B.L

O.G.RB.B

O.G.RB.L

O.G.B.L

O.RB.B.L

G.RB.B.L

R.O.G.RB.B

R.O.G.RB.L

R.O.G.B.L

R.O.RB.B.L

R.G.RB.B.L

O.G.RB.B.L

R.O.G.RB.B.L

ð

Dimmer (000~255) Default:

R.O.G.RB.B.L

Dimmer=255

Color Picker

ð

3200K

71

97

100

101

102

103

104

105

106

107

110

111

113

115

116

117

118

119

120

121

122

124

126

128

130

132

134

135

136

137

138

139

141

144

147

151

152

156

157

158

161

164

165

166

170

174

179

180

181

182

195

197

198

200

201

202

203

204

205

206

702

730

777

ð

Dimmer (000~255) Default: 3200K

Manual Color

ð

Red

Orange

Green

Royal Blue

Blue

Lime

ð

(000~255) Default:

RGBW=255

ECLFRJPTW

14

15

ECLFRJPTW

3.4 DMX MODE

• To set the DMX address, press the button MENU so many times until the display shows Connect, then

select throught the buttons UP/DOWN Dmx Address, then press the button ENTER.

• Press UP/DOWN button to select the desired value (001-512). Press and hold to scroll quickly.

• Press ENTER button to store.

• Press the MENU button to go back or to meet the waiting time to exit the setup menu.

To operate the ECLFRJPTW with a light controller, adjust the DMX start address for the rst a DMX channel.

For example, If the controller is provided with to command the function of the rst DMX channel, adjust

the start address 33 on the ECLFRJPTW. The other functions of the light eect panel are then automatically

assigned to the following addresses.

An example with the start address 33 is shown below:

DMX Address: 48DMX Address: 38DMX Address: 33 DMX Address: 43

Fig.9 - Example 5 DMX channels conguration

DMX512 Controller

Number of

DMX channels

Start address

(example)

DMX Address

occupied

Next possible start

address for unit No. 1

Next possible start

address for unit No. 2

Next possible start

address for unit No. 3

1 33 33 34 35 36

2 33 33-34 35 37 39

5 33 33 - 37 38 43 48

7 33 33 - 39 40 47 54

8 33 33 - 40 41 49 57

9 33 33 - 41 42 51 60

12 33 33 - 44 45 57 69

13 33 33 - 45 46 59 72

16 33 33 - 48 49 65 81

19 33 33 - 51 52 71 90

21 33 33 - 53 54 75 96

. . . . . . . . . . . .

ECLFRJPTW

16

3.5 DMX CONFIGURATION

ECLFRJPTW has several DMX channel congurations that can be accessed from the control panel.

• Press the button MENU so many times until the display shows Connect, then select throught the buttons

UP/DOWN DMX Channel, then press the button ENTER.

• Select the desired DMX conguration (1CH, 2CH, 5CH1, 5CH2, 7CH1, 7CH2, 9CH, 12CH, 13CH, 16CH, 19CH, 21CH)

through the buttons UP/DOWN.

3.6 LINKING

1. Connect the DMX OUT output of the main unit to the DMX IN input of the rst secondary unit using a

5-pin XLR cable.

2. Connect the DMX OUT output of the rst secondary unit to the DMX IN input of the second secondary

unit, etc.

3.7 SCREEN

It is possible to modify the following parameters, related to the display, following the same procedure:

• Press the button MENU to enter the menu mode.

• Press UP/DOWN button to scroll through the menu, select Set Up, then press the ENTER button to access

the next menu.

• Press UP/DOWN button to select Screen and press the ENTER button to proceed.

• Select the proposed option and press the ENTER button to conrm.

- Backlight - Auto O display backlight. This function allows you to switch o automatically the back-

lighting of the display after a certain time which can be set using the directional keys. To have the

display always on select On or set a value between those shown (10s, 20s, 30s) to turn o the display

once the chosen time has elapsed, after exiting the menu.

- Flip Display - Display orientation. This feature allows you to rotate the display by 180 ° to get a better

view of the display when the unit is hanging upside down. Select Yes to activate the function, No to

deactivate it.

- Key lock - With this function, you can lock the keys on the control panel to prevent, for example, tam-

pering with the settings. If this function is activated, the keys are locked automatically. To disable or

temporarily disable or disable the key lock function, press the keys in the following order to regain

access to the menu commands: UP, DOWN, UP, DOWN, ENTER. Select Yes to activate the function or

No to deactivate it.

• Press the ENTER button to conrm the selection.

• Press the MENU button to go back or to meet the waiting time to exit the setup menu.

3.8 ADVANCED

You can change the parameters for the device by following these steps:

• Press the button MENU to enter the menu mode.

• Press UP/DOWN button to select the Advanced. Press the ENTER button to conrm.

• Press UP/DOWN button to select the desired option and press the ENTER button to conrm:

- Full On Mode - Select the Full on Mode function to set the HB mode (High Brightness Mode, with the

- maximum value of the colours) or Studio mode with a automatic white balance.

- Dimmer Mode - Adjusting the dimmer. Enter in Dimmer Mode to select specic dimming curve.

Particularly when set:

• O: The increase in light intensity is linear.

• Dimmer 1: dimmer curve with low fade.

• Dimmer 2: dimmer curve with medium fade.

17

ECLFRJPTW

• Dimmer 3: dimmer curve with high fade.

- White Balance - To balance the white on each colour. Select the colour (Red, Orange, Green, Royal Blue,

Blue and Lime) and the value (125 ~ 255) using the UP / DOWN button and press the ENTER button to

conrm.

- LED Frequency - To adjust the frequency of the LEDs. Select the frequency 600 Hz ~ 25 KHz using the UP /

DOWN button and press ENTER to conrm the selection.

- Fan Mode - Fan Speed. Select the fan speed (Auto, On, O, Silent) using the UP / DOWN button.

- Factory Reload - To reset the unit. Select Yes or No and select the UP / DOWN button to conrm.

• Press the MENU button to go back or to meet the waiting time to exit the setup menu.

3.9 INFORMATION

To view all the information on the device, proceed as follows:

• Press the button MENU to enter the menu mode.

• Press UP/DOWN button to select Information, then press the ENTER button to access the next menu.

• Press UP/DOWN button to scroll through the menu, then select one of the following informationa and

press the ENTER button to display it.

- Fixture Time - To view the operating time of the projector.

- Software Version - To view the rmware version will show on the display.

- UID - To view the identication ID for the RDM control.

• Press the MENU button to go back or to meet the waiting time to exit the setup menu.

3.10 MASTER/SLAVE MODE

This mode will allow you to link up the units together without a controller. The rst unit will be set as mas-

ter and other units will work as slave with the same eect.

• Press the button MENU so many times until the display shows Stand Alone, then select throught the

buttons UP/DOWN Master/Slave, then press the button ENTER.

• Press UP/DOWN and select the Master/Slave mode to set the unit as master or slave (Master, Slave).

• Use the ECLFRJPTW DMX connectors and an XLR cable to form a drive chain. In certain conditions and

lengths, it is recommended to terminate as shown on page 18.

3.11 EFFECTS

This xture has a built-in automatic program. To access this, please see the below instructions:

• To enter the Eects mode, press the ENTER button to access the menu.

• Press UP/DOWN button to select Stand Alone, then select Eect. Press ENTER to conrm

• Press UP/DOWN button to select the desired program Eect 1, Eect 2, Eect 3, Eect 4, Eect 5 then press

ENTER to conrm.

• Set the value (1 - 100), then press the ENTER button to conrm.

3.12 STATIC MODE

This xture has the ability to accept custom static color settings. Access these chases via the control panel

on the back of the xture.

• Press the MENU button so many times until the display shows Stand Alone, then press the ENTER button.

• Select Fixed Color through the UP/DOWN buttons, then press the ENTER button.

• Set the colors R , O, G, W, RB, B, L, R.O.G.RB.B.L... R.G.RB.B.L, O.G.RB.B.L, R.O.G.RB.B.L through the UP/DOWN but-

tons, then press the ENTER button.

• Press the MENU button to go back or to meet the waiting time to exit the setup menu.

ECLFRJPTW

18

3.13 MANUAL MODE

To set the customized balance of red, orange, green, royal blue, blue and lime colors, refer to the following

procedure:

• Press the button MENU so many times until the display shows Stand Alone, then select throught the

buttons UP/DOWN Static, then press the button ENTER.

• Select Manual Color Mixer through the buttons UP/DOWN, then press the button ENTER.

• Select the color Red, Orange, Green, Royal Blue, Blue, Lime through the buttons UP/DOWN, then press the

button ENTER.

• Using UP/DOWN button, select the desired color value 000 ~ 255.

• Press ENTER button to continue to the next color Red, Orange, Green, Royal Blue, Blue, Lime.

• Continue until the desired mix is obtained.

• Press the MENU button to go back or to meet the waiting time to exit the setup menu.

La pagina si sta caricando...

ProLights ECLFRJPTW Manuale utente

ProLights ECLFRJPTW Manuale utente

in altre lingue

Documenti correlati

Altri documenti