ProLights LED Fresnel Manuale utente

Marca: ProLights

Modello: LED Fresnel

Categoria: Proiettori

Tipo: Manuale utente

USER MANUAL

MANUALE UTENTE

ECLFRESNELPTU-DY

ECLFRESNELTU-DY

EN - IT

MINI LED ELLIPSOIDAL

reproduced in any form or by any means for any commercial use.

In order to improve the quality of products, Music&Lights S.r.l. reserves the right to modify the

characteristics stated in this instruction manual at any time and without prior notice.

All revisions and updates are available in the ‘manuals’ section on site www.musiclights.it

REV.01-09/18

ECLFRESNELTU-DY-PTU-PDY

Packing content

• ECLFRESNEL/P

• User manual

TABLE OF CONTENTS

Safety

General instructionsGeneral instructions

Warnings and installation precautionsWarnings and installation precautions

1 Introduction

1. 1 Description and specications1. 1 Description and specications

1. 2 Operating elements and connections1. 2 Operating elements and connections

2 Installation

2. 1 Mounting2. 1 Mounting

3 Functions and settings

3. 1 Operation3. 1 Operation

3. 2 Basic3. 2 Basic

3. 3 Menu structure3. 3 Menu structure

3. 4 DMX mode3. 4 DMX mode

3. 5 DMX conguration3. 5 DMX conguration

3. 6 Setting3. 6 Setting

3. 7 Channels DMX3. 7 Channels DMX

3. 8 Fixture settings3. 8 Fixture settings

Dimmer Dimmer

Led frequency Led frequency

Factory Reload Factory Reload

3. 9 Fixture Information3. 9 Fixture Information

3. 10 Operations in automatic mode3. 10 Operations in automatic mode

Master/Slave Master/Slave

Eects Eects

4 Maintenance

4. 1 Maintenance and cleaning the unit4. 1 Maintenance and cleaning the unit

4. 2 Trouble shooting4. 2 Trouble shooting

ECLFRESNELTU-DY-PTU-PDY

SAFETY

General instruction

• The products referred to in this manual conform to the European Community Directives and are there-

fore marked with .

• The unit is supplied with hazardous network voltage (230V~). Leave servicing to skilled personnel only.

Never make any modications on the unit not described in this instruction manual, otherwise you will

risk an electric shock.

• Connection must be made to a power supply system tted with ecient earthing (Class I appliance ac-

cording to standard EN 60598-1). It is, moreover, recommended to protect the supply lines of the units

from indirect contact and/or shorting to earth by using appropriately sized residual current devices.

• The connection to the main network of electric distribution must be carried out by a qualied electrical

installer. Check that the main frequency and voltage correspond to those for which the unit is designed

as given on the electrical data label.

• This unit is not for home use, only professional applications.

• Never use the xture under the following conditions:

- in places subject to vibrations or bumps;

- in places with a temperature of over 45 °C.

• Make certain that no inammable liquids, water or metal objects enter the xture.

• Do not dismantle or modify the xture.

• All work must always be carried out by qualied technical personnel. Contact the nearest sales point for

an inspection or contact the manufacturer directly.

• If the unit is to be put out of operation denitively, take it to a local recycling

plant for a disposal which is not harmful to the environment.

Warnings and installation precautions

• If this device will be operated in any way dierent to the one described in this manual, it may suer

damage and the guarantee becomes void. Furthermore, any other operation may lead to dangers like

short circuit, burns, electric shock, etc.

• Before starting any maintenance work or cleaning the projector, cut o power from the main supply.

• Always additionally secure the projector with the safety rope. When carrying out any work, always com-

ply scrupulously with all the regulations (particularly regarding safety) currently in force in the country

in which the xture’s being used.

• Install the xture in a well ventilated place.

• Keep any inammable material at a safe distance from the xture.

• Shields, lenses or ultraviolet screens shall be changed if they have become damaged to such an extent

that their eectiveness is impaired.

• The lamp (LED) shall be changed if it has become damaged or thermally deformed.

• Never look directly at the light beam. Please note that fast changes in lighting, e. g. ashing light, may

trigger epileptic seizures in photosensitive persons or persons with epilepsy.

• Do not touch the product’s housing when operating because it may be very hot.

• This product was designed and built strictly for the use indicated in this documentation. Any other use,

not expressly indicated here, could compromise the good condition/operation of the product and/or

be a source of danger.

• We decline any liability deriving from improper use of the product.

WARNING! Before carrying out any operations with the unit, carefully read this instruction

manual and keep it with cure for future reference. It contains important information about

the installation, usage and maintenance of the unit.

ECLFRESNELTU-DY-PTU-PDY

- 1 - INTRODUCTION

1.1 ECLFRESNEL - DESCRIPTION AND TECHNICAL SPECIFICATIONS

ECL FRESNEL is the LED replacement for a standard tungsten 1K fresnel. Featuring the output character-

istics of a traditional Fresnel but with beam control, functional barn doors and a powerful source that

focuses on outstanding colour rendition. The ECLFRESNEL adds all the advantages of LED to the Fresnel.

LIGHT SOURCE

• Source: 1x230W high-power white LED

• CT: (TU) 3200 K - (DY) 5600K

• CRI: (TU) 97 Ra - (DY) 95

• R9: >90

• Luminous ux: (TU) (45°) 12300 lm (15°) 10520 lm - (DY) (45°) 13530 lm (15°) 11492lm

• Lux: (TU) - (15°) 11166 lux - (45°) 3250 - (DY) - (15°) 12600 lux - (45°) 3330lux @3m

• Lux: (TU) - (15°) 4020 lux - (45°) 1170 - (DY) - (15°) 4536 lux - (45°) 1178lux @5m

• Source life expectancy: >50.000 h

• Other: TLCI: (TU - 15°) 98.1, (TU - 45°) 98

OPTICS

• Zoom: 15°~45° manual

• Beam angle: 15°~45°

• Field angle: 28°~65°

• Lens diameter: 8’’-200mm

• Lens type: Fresnel zoom lens from 15° to 45°

• Other: Barn door and gel frame included

COLOUR SYSTEM

• Colour mixing: white

DYNAMIC EFFECTS

• Static colour mode: selection of static dimmer

• Manual colour mode: manual adjust of dimmer throught menu and knob

• Auto mode: built-in programs with execution speed adjustment

BODY

• Hardware on-board: lter frame, 8 doors barndoor, omega bracket spigot

• Body: sturdy die-cast aluminium body conceived for long-time durability

• Body colour: black

• Other: Pan/Tilt innite for pole operated version

CONTROL

• Protocols: DMX512, RDM, Local knob

• DMX channels: 1 / 2 ch1 / 2 ch2 / 3 / 5channel

• RDM: RDM ready for xture remote monitor and settings

• Display: LCD high resolution colour display with autoip

• Firmware upgrade: yes, via USB-DMX interface (UPBOX1) not included

• Master/Slave: for synchronized operation of more units linked in a chain

• Other: 16bit control of dimmer and colour

ECLFRESNELTU-DY-PTU-PDY

ELECTRONICS

• Dimmer: linear 0~100%, manual knob dimmer

• Dimmer curves: dierent dimming curves available

• Strobe / shutter: 0~30 Hz, electronic

• Operating temperature: -10° ~ +45°

• Flicker: icker free frequency with adjustable PWM

• Selectable PWM: 600~25K Hz

ELECTRICAL

• Power supply: 100-240V – 50/60Hz

• Power consumption (at 230V): 214W

• Power consumption (at 120V): 215W

• Output (at 230V): 17 units on a single power line

• Output (at 120V): 9 units on a single power line

• Power factor: 0,95

PHYSICAL

• Cooling: combination of heat pipe cooling system and low noise fan

• Sospension and xing: hanging bracket suitable for safe hanging and positioning

• Signal connection: Amphenol XLR 5p IN/OUT connectors

• Power connection: Neutrik powerCON TRUE1 IN/OUT connectors

• IP rating: 20

• Dimensions (WxHxD): for standard version 343x539x283 mm, for pole operated version 545x341x343mm

• Weight: for standard version 7.5 kg, for pole operated version 9.2kg

ECLFRESNELTU-DY-PTU-PDY

Fig.1 - Technical drawing

ECLFRESNEL

ECLFRESNELP

343283

439

100

341 343

429

116

ECLFRESNEL

10 11 12

Fig.2 a

ECLFRESNELTU-DY-PTU-PDY

1.2 OPERATING ELEMENTS AND CONNECTIONS

1. AIR OPENING

2. LOCKING KNOB for mounting bracket

3. MOUNTING BRACKET

4. TRACK-ADAPTER(optional)

5. HANDLE

6. CONTROL PANEL with display and 1 button

used to access the control panel functions

and manage them

7. FOCUS AND ZOOM ADJUSTING SCREW to

zoom the projected image clearly

8. MAIN FUSE HOLDER: replace a burnt-out fuse

by one of the same type only

9. POWER IN (PowerCON IN): for connection to a

socket (100-240V~/50-60Hz) via the supplied

mains cable.

10. DMX IN (5-pole XLR): 1 = ground, 2 = DMX-, 3

= DMX+, 4 N/C, 5 N/C

11. DMX OUT (5-pole XLR): 1 = ground, 2 = DMX-,

3 = DMX+, 4 N/C, 5 N/C

12. POWER OUT (PowerCON OUT): power output

for connection of multiple units in series.

ECLFRESNELP

9 10 11

1. AIR OPENING

2. MOUNTING BRACKET

3. TRACK-ADAPTER

4. HANDLE

5. CONTROL PANEL with display and 4 button

used to access the control panel functions

and manage them

6. FOCUS AND ZOOM ADJUSTING SCREW to

zoom the projected image clearly

7. MAIN FUSE HOLDER: replace a burnt-out fuse

by one of the same type only

8. POWER IN (PowerCON IN): for connection to a

socket (100-240V~/50-60Hz) via the supplied

mains cable.

9. DMX IN (5-pole XLR): 1 = ground, 2 = DMX-, 3

= DMX+, 4 N/C, 5 N/C

10. DMX OUT (5-pole XLR): 1 = ground, 2 = DMX-,

3 = DMX+, 4 N/C, 5 N/C

11. POWER OUT (PowerCON OUT): power output

for connection of multiple units in series.

12. YELLOW POLE OPERATOR: Zoom pole

operator.

13. WHITE POLE OPERATOR: Tilt pole operator.

14. BLUE POLE OPERATOR: Pan pole operator

Fig.2 b

ECLFRESNELTU-DY-PTU-PDY

Fig.3

A B

ECLIPSEFRESNELPECLIPSEFRESNEL

ECLFRESNELTU-DY-PTU-PDY

- 2 - INSTALLATION

2.1 MOUNTING

ECLFRESNEL is designed for applications in exhibition areas, commercial spaces, museums, restaurant,

churches, and any other installation where size is an important factor. For xing, stable mounting clips are

required. The mounting place must be of sucient stability and be able to support a weight of 10 times

of the unit’s weight.

When carrying out any installation, always comply scrupulously with all the regulations (particularly re-

garding safety) currently in force in the country in which the xture’s being used.

• Install the projector at a suitable location.

• Always additionally secure the projector with the safety rope from falling down. For this purpose, fas-

ten the safety rope at a suitable position so that the maximum fall of the projector will be 20 cm. The

adjust the projector and use the knobs.

NOTE - For the installation of the ECLFRESNELDY make sure that the ridge of the adaptor is in with the

groove of the track. Turn knobs 90° to connect the adaptor to the circuit. Please see the gure 4.

ECLFRESNELTU-DY-PTU-PDY

- 3 - FUNCTIONS AND SETTINGS

3.1 OPERATION

To turn on the ECLFRESNEL connect the supplied main cable to a socket (100-240 VAC-50/60 Hz). Then the

unit is ready for operation. You can also adjust the dimmer and zoom using the knobs.

To switch o, disconnect the mains plug from the socket. For a more convenient operation it is recom-

mended to connect the unit to a socket which can be switched on and o via a light switch.

NOTE - To operate the projector ECLFRESNEL you need a system track. The track system must be installed

and maintained by a suitably qualied person in compliance with latest construction and relevant legisla-

tion. It is the responsibility of the installer to ensure the electrical, mechanical and thermal compatibility

of the track system and the ttings. The connection to the main network of electric distribution must be

carried out by a qualied electrical installer.

ATTENTION - Mains voltage must be switched o before mounting; maintenance; insert and replace

Adaptors; spots and luminaires.

3.2 BASIC

Access control panel functions using the four panel buttons located directly underneath the LED Display

(g.5).

Fig.4- Functions of the buttons

1 CONNECT

DMX Address

Value (001-512)

DMX Mode

EASY 1CH

BASIC 2CH 1

BASIC 2CH 2

BASIC 3CH

STANDARD 5CH

2 SETUP

Screen

Back Light

10S

20S

30S

Flip Display

NO-Yes

3 ADVANCED

Dimmer Mode

O

Dimmer 1

Dimmer 2

Dimmer 3

Led Frequency

600Hz

1200 Hz

2000 Hz

4000 Hz

6000Hz

25kHZ

Fan Mode

Auto

Factory Reload

NO-Yes

4 INFORMATION

Fixture Hours

0-9999

Version

V1.0

UID

15D00217****

5 STANDALONE

Master/Slave

Eects

Eect 1 Speed 1~100

Eect 2

Eect 3

Eect 4

Static

Dimmer

Strobe

ECLFRESNELTU-DY-PTU-PDY

3.3 MENU STRUCTURE

ECLFRESNELTU-DY-PTU-PDY

3.4 DMX MODE

• Press the button MENU so many times until the display shows DMX ADDRESS, and press the button ENTER

to conrm.

• Press UP/DOWN button to select the desired value (001-512). Press and hold to scroll quickly.

• Press ENTER button to store.

• Press the MENU button to go back or to meet the waiting time to exit the setup menu.

To able to operate the ECLFRESNEL/TRWD with a light controller, adjust the DMX start address for the rst

a DMX channel. If e. g. address 33 on the controller is provided for controlling the function of the rst DMX

channel, adjust the start address 33 on the ECLFRESNEL. The other functions of the light eect panel are

then automatically assigned to the following addresses.

An example with the start address 33 is shown below:

3.5 DMX CONFIGURATION

ECLFRESNEL/TRWD is equipped with dierent DMX conguration.

• Press the button MENU so many times until shows DMX CHANNEL, and press the button ENTER to conrm.

• Select the desired DMX conguration (EASY 1CH - BASIC 2CH 1 - BASIC 2CH 2 - BASIC3CH - STANDARD 5CH ) through

the buttons UP/DOWN.

3.6 SETTINGS

You can change the parameters for the device by following these steps:

SCREEN

You can change the following parameters related to the display, following the same procedure:

• Press the ENTER button to access the main menu.

• Press the UP / DOWN keys to scroll the menu, select the Set Up icon, then press the ENTER button to

enter the next menu.

• Press UP / DOWN to scroll through the menu, then select Screen, and press the ENTER button to enter

the next menu.

• Press UP / DOWN to scroll through the menu, and then select one of the following settings for the dis-

play and press the ENTER key to display it.

- Back Light - Backlight display Auto O. This feature allows you to automatically turn o the backlight

after a specied time that you can set using the arrow buttons. To have the display always on select

Always On or choose another value to turn o the display after the amount of time you choose.

- Flip Display - Orientation of the display. This function allows you to rotate the display 180° to get a

better view of the display when the unit is hanging upside down. Select YES to activate or NO to dis-

able this function.

• Press the ENTER button to conrm your choice.

• Press the LEFT button repeatedly to exit the menu and save changes.

Numero

canali DMX

Indirizzo di

start (esempio)

Indirizzo DMX

occupati

Prossimo indirizzo di start

possibile per unità n°1

Prossimo indirizzo di start

possibile per unità n°2

Prossimo indirizzo di start

possibile per unità n°3

5 33 33 - 37 38 43 48

1 CHANNELS

MODE

FUNCTION DMX

Value

1 Ch

DIMMER

0~100% 000 - 255

2 CHANNELS 2

MODE

FUNCTION DMX

Value

2 Ch

DIMMER

0~100% 000 - 255

STROBE

NO Function

Strobe Slow to Fast

000 - 010

011 - 255

3 CHANNELS

MODE

FUNCTION DMX

Value

3 Ch

DIMMER

0~100% 000 - 255

DIMMER FINE

0~100% 000 - 255

STROBE

NO Function

Strobe Slow to Fast

000 - 010

011 - 255

5 CHANNELS

MODE

FUNCTION DMX

Value

5 Ch

DIMMER

0~100% 000 - 255

STROBE

NO Function

Strobe Slow to Fast

000 - 010

011 - 255

AUTO PROGRAMS

No Function

Auto Program 1

Auto Program 2

Auto Program 3

Auto Program 4

000 - 010

011 - 070

071 - 130

131 - 190

191 - 255

AUTO SPEED

Auto speed slow to fast 000 - 255

DIMMER SPEED MODE

Preset dimmer speed from display menu

Dimmer speed mode o

Dimmer speed mode1 (fast speed)

Dimmer speed mode2 (middle speed)

Dimmer speed mode3 (slow speed)

000 - 051

052 - 101

102 - 152

153 - 203

204 - 255

2 CHANNELS 1

MODE

FUNCTION DMX

Value

2 Ch

DIMMER

0~100% 000 - 255

DIMMER FINE

0~100% 000 - 255

ECLFRESNELTU-DY-PTU-PDY

3.7 CHANNELS DMX

ECLFRESNELTU-DY-PTU-PDY

3. 8 FIXTURE SETTINGS

It is possible to change the parameter value in the following way:

DIMMER

• Enter in Dimmer mode to select specic dimming curve, press the button MENU so many times until

shows DIM MODE, and press the button ENTER to conrm.

• Press the button UP/DOWN to select OFF - DIM1 - DIM2 - DIM3.

• Press ENTER button to store.

• Press the MENU button to go back or to meet the waiting time to exit the setup menu.

LED FREQUENCY

• To adjust the frequency of the LEDs, press the MENU button repeatedly until the display shows LED

Frequency, and then press the ENTER button.

• Select the frequency (600Hz - 1200Hz - 2000Hz - 4000Hz - 6000Hz - 25kHz) using the UP/DOWN buttons.

• To conrm, press the ENTER key.

• Press the MENU button to go back or wait a few seconds to exit the setup menu.

FACTORY RELOAD

Selezionare questa funzione per ripristinare l’unità alle impostazioni di fabbrica:

• To activate Reset Factory display press the button MENU so many times until shows Factory Reload,

and press the button ENTER to conrm.

• Press ENTER button to conrm the selection.

• Press the MENU button to go back or to meet the waiting time to exit from the setup menu automati-

cally.

3. 9 FIXTURE INFORMATION

To view all the information on the device, proceed as follows:

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select the icon Information, then press the ENTER but-

ton to enter the next menu.

• Press the UP/DOWN button to scroll through the menu, then select one of the following information

and press the ENTER button to display it.

- Fixture Time - Through the Fixture Time function you can display the operating time of the projector.

- Software Version - Through Version function you can display the currently installed software version.

• Press the LEFT button repeatedly to exit the menu.

3. 10 OPERATIONS IN AUTOMATIC MODE

MASTER SLAVE

Press the UP/DOWN button to scroll through the menu, select Master/Slave and press ENTER to conrm your

choice.

• Press the UP/DOWN button to select the mode of operation:

- Master, if the unit is connected in series with other units and it acts as the Master;

- Slave, if the unit is not connected to other units.

• Press the ENTER button to conrm your choice.

EFFECTS

The unit independently runs through its show. Before you send an automatic program you need to set the

drive as Master/Alone:

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select the Eects icon, then press the ENTER button to

ECLFRESNELTU-DY-PTU-PDY

enter the next menu.

• Press the UP/DOWN button to select the mode of operation: Eects 1, Eects 2, Eects 3, Eects 4

• Press the ENTER button to conrm your choice.

• Press the LEFT button repeatedly to exit the menu and save changes.

The unit will go into automatic mode by executing the program automatically.

ECLFRESNELTU-DY-PTU-PDY

- 4 - MAINTENANCE

4.1 MAINTENANCE AND CLEANING THE UNIT

• Make sure the area below the installation place is free from unwanted persons during setup.

• Switch o the unit, unplug the main cable and wait until the unit has cooled down.

• All screws used for installing the device and any of its parts should be tightly fastened and should not

be corroded.

• Housings, xations and installation spots (ceiling, trusses, suspensions) should be totally free from any

deformation.

• The main cables must be in impeccable condition and should be replaced immediately even when a

small problem is detected.

• It is recommended to clean the front at regular intervals, from impurities caused by dust, smoke, or

other particles to ensure that the light is radiated at maximum brightness. For cleaning, disconnect the

main plug from the socket. Use a soft, clean cloth moistened with a mild detergent. Then carefully wipe

the part dry. For cleaning other housing parts use only a soft, clean cloth. Never use a liquid, it might

penetrate the unit and cause damage to it.

4.2 TROUBLESHOOTING

Problems Possible causes Checks and remedies

Fixture does not light up

• No mains supply

• Dimmer fader set to 0

• Faulty LED

• Check the power supply voltage

• Increase the value of the dimmer channels

• Replace the LED board

General low light intensity

• Dirty lens assembly

• Misaligned lens assembly

• Clean the xture regularly

• Install lens assembly properly

Fixture does not power up

• No power

• Loose or damaged power cord

• Check for power on power outlet

• Check power cord

Contact an authorized service center in case of technical problems or not reported in the table can not be

resolved by the procedure given in the table.

Music & Lights S.r.l. si riserva ogni diritto di elaborazione in qualsiasi forma delle presenti istruzioni per l’uso.

La riproduzione - anche parziale - per propri scopi commerciali è vietata.

Al ne di migliorare la qualità dei prodotti, la Music&Lights S.r.l. si riserva la facoltà di modicare, in

qualunque momento e senza preavviso, le speciche menzionate nel presente manuale di istruzioni.

Tutte le revisioni e gli aggiornamenti sono disponibili nella sezione 'Manuali' sul sito www.musiclights.it

ECLFRESNELTU-DY-PTU-PDY

• ECLFRESNEL/P

• Manuale utente

Contenuto dell'imballo:

INDICE

Sicurezza

Avvertenze generaliAvvertenze generali

Attenzioni e precauzioni per l’installazioneAttenzioni e precauzioni per l’installazione

1 Introduzione

1. 1 Descrizione e speciche tecniche1. 1 Descrizione e speciche tecniche

1. 2 Elementi di comando e di collegamento 1. 2 Elementi di comando e di collegamento

2 Installazione

2. 1 Montaggio2. 1 Montaggio

3 Funzioni e impostazioni

3. 1 Funzionamento3. 1 Funzionamento

3. 2 Impostazione base3. 2 Impostazione base

3. 3 Struttura menù3. 3 Struttura menù

3. 4 Modalità DMX3. 4 Modalità DMX

3. 5 Congurazione canali3. 5 Congurazione canali

3. 6 Canali DMX3. 6 Canali DMX

3. 7 Impostazioni del proiettore3. 7 Impostazioni del proiettore

3. 8 Funzioni del dispositivo3. 8 Funzioni del dispositivo

Dimmer Dimmer

Frequenza led Frequenza led

Factory Reload Factory Reload

3. 9 Informazioni sul dispositivo3. 9 Informazioni sul dispositivo

3. 11 Modalità Automatica3. 11 Modalità Automatica

Master/Slave Master/Slave

Eects Eects

4 Manutenzione

4. 1 Manutenzione e pulizia del sistema ottico4. 1 Manutenzione e pulizia del sistema ottico

4. 2 Risoluzione dei problemi4. 2 Risoluzione dei problemi

ECLFRESNELTU-DY-PTU-PDY

ATTENZIONE! Prima di effettuare qualsiasi operazione con l’unità, leggere con attenzione

questo manuale e conservarlo accuratamente per riferimenti futuri. Contiene informazioni

importanti riguardo l’installazione, l’uso e la manutenzione dell’unità.

SICUREZZA

Avvertenze generali

• I prodotti a cui questo manuale si riferisce sono conformi alle Direttive della Comunità Europea e per-

tanto recano la sigla .

• Il dispositivo funziona con pericolosa tensione di rete 230V~. Non intervenire mai al suo interno al di

fuori delle operazioni descritte nel presente manuale; esiste il pericolo di una scarica elettrica.

• È obbligatorio eettuare il collegamento ad un impianto di alimentazione dotato di un’eciente messa

a terra (apparecchio di Classe I secondo norma EN 60598-1). Si raccomanda, inoltre, di proteggere le

linee di alimentazione delle unità dai contatti indiretti e/o cortocircuiti verso massa tramite l’uso di

interruttori dierenziali opportunamente dimensionati.

• Le operazioni di collegamento alla rete di distribuzione dell’energia elettrica devono essere eettuate

da un installatore elettrico qualicato. Vericare che frequenza e tensione della rete corrispondono alla

frequenza ed alla tensione per cui l’unità è predisposta, indicate sulla targhetta dei dati elettrici.

• L’unità non per uso domestico, solo per uso professionale.

• Evitare di utilizzare l’unità:

- in luoghi soggetti a vibrazioni, o a possibili urti;

- in luoghi a temperatura superiore ai 45°C.

• Evitare che nell’unità penetrino liquidi inammabili, acqua o oggetti metallici.

• Non smontare e non apportare modiche all’unità.

• Tutti gli interventi devono essere sempre e solo eettuati da personale tecnico qualicato. Rivolgersi al

più vicino centro di assistenza tecnica autorizzato.

• Se si desidera eliminare il dispositivo denitivamente, consegnarlo

per lo smaltimento ad un’istituzione locale per il riciclaggio.

Attenzioni e precauzioni per l’installazione

• Se il dispositivo dovesse trovarsi ad operare in condizioni dierenti da quelle descritte nel presente

manuale, potrebbero vericarsi dei danni; in tal caso la garanzia verrebbe a decadere. Inoltre, ogni altra

operazione potrebbe provocare cortocircuiti, incendi, scosse elettriche, rotture etc.

• Prima di iniziare qualsiasi operazione di manutenzione o pulizia sull’unità togliere la tensione dalla rete

di alimentazione.

• È assolutamente necessario proteggere l’unità per mezzo di una fune di sicurezza. Nell’eseguire qual-

siasi intervento attenersi scrupolosamente a tutte le normative (in materia di sicurezza) vigenti nel

paese di utilizzo.

• Installare l’unità in un luogo ben ventilato.

• Mantenere i materiali inammabili ad una distanza di sicurezza dall’unità.

• I ltri, le lenti o gli schermi ultravioletti se danneggiati possono limitare la loro ecienza.

• I LED devono essere sostituiti se danneggiati o termicamente deformati.

• Non guardare direttamente il fascio luminoso. Tenete presente che i veloci cambi di luce possono pro-

vocare attacchi d’epilessia presso persone fotosensibili o epilettiche.

• Non toccare l’alloggiamento del prodotto quando è in funzione perché potrebbe essere molto caldo.

• Questo prodotto è stato progettato e costruito esclusivamente per l’utilizzo indicato in questa docu-

mentazione. Qualsiasi altro utilizzo non espressamente indicato potrebbe pregiudicare la funzionalità

del prodotto e/o rappresentare fonte di pericolo.

• Si declina qualsiasi responsabilità derivata dall’uso improprio del prodotto.

La pagina sta caricando ...

ProLights LED Fresnel Manuale utente

Marca: ProLights

Modello: LED Fresnel

Categoria: Proiettori

Tipo: Manuale utente

Scarica il pdf

rapporto

in altre lingue

English: ProLights LED Fresnel User manual

Documenti correlati

Altri documenti

Danfoss ECL 2000 Istruzioni per l'uso