Sylvania SLED5516A Manuale del proprietario

SLED5516A

55”

LED TV

USER’S MANUAL

Sylvania is a registered trademark of OSRAM SYLVANIA INC. used under license.

Contents

 Introduction

 Warning

 Caution

 Important Information

 Attaching or

Removing the Stand

 Installing Batteries to the Remote Control

 Identifying Front and Rear Panel

 Connection Suggestion

 Main Unit Description

 Remote Control

 OSD Basic Adjustment

 How Do I Clean The TV

 Troubleshooting

 Specifications

 FCC Compliance Statement

Intr

oduction

Thank

you very much for purchasing your LED TV. It serves as a normal colour TV

and a PC monitor. To enjoy your set fully from the very beginning, read this manual

carefully and keep it handy for future reference.

INST

ALLATION

① Locate the receiver in the room where direct light does not strike the screen. Total

darkness or a reflection on the picture screen can cause eyestrain. Soft and indirect

lighting is recommended for comfortable viewing.

② Allow enough space between the receiver and the wall to permit ventilation.

③ Avoid excessively warm locations to prevent possible damage to the cabinet or

premature component failure.

④ This TV can be connected to AC 100-240V~ 50/60HZ.

⑤ Do not install the TV in a location near heat sources such as radiators, air ducts,

direct sunlight, or in closed compartments and closed areas. Do not cover the

ventilation openings when using the TV.

The indicator light will last for about 30 seconds after the power has been turned

off.

Wait until the indicator light goes out before repowering the TV.

6

User manual x1

Warranty card x1

Remote control x1

Battery (pair, AAA) x1

Accessories list for this TV set:

x

Warning

This symbol is intended to alert the user to avoid the risk

of electric shock. This equipment may only be disassembled

by qualified service personnel.

This symbol is intended to alert the user to the presence

of important operation and maintenance instructions in

the literature accompanying the equipment.

CAUTION: TO AVOID THE RISK OF ELECTRIC SHOCK.

DO NOT REMOVE COVER (OR BACK).

NO USER- SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL

.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

Class I structures of equipment should be connected to the grid

power output with a protective earth connection on the socket.

Power plug as a broken appliance，

broken installations should

be easy to operate.

Caution

High voltages are used in the operation of this product.

- Do not open the product's casing. Refer servicing

to qualified service personnel .

Caution

To prevent fire or electrical shock hazard, do not expose

the main unit to

rain or moisture，

do not place objects

filled with liquids, such as vases, on the apparatus.

Caution

Do not drop or push objects into the television cabinet

slots or openings. Never spill any kind of liquid on the

television receiver.

Caution

Avoid exposing the main unit to direct sunlight and other

sources of heat. Do not stand the television receiver

directly on other products which give off heat: e. g. video

cassette players and audio amplifiers. Do not block the

ventilation holes in the back cover. Ventilation is essential

to prevent failure of electrical components. Do not squash

the power supply cord under the main unit or other heavy

objects.

Caution

Never stand on, lean on or suddenly push the product

or its stand. You should pay special attention to

children.

Caution

Do not place the main unit on an unstable cart stand,

shelf or

table. Serious injury to an individual and

damage to the television may result if it should fall.

Caution

When the product is not used for an extended period

of time, it is advisable to disconnect the AC power

from the AC outlet.

Caution

The LED panel used in this product is made of glass and

is ther

efore breakable. This product must not be dropped

or banged. If the LED Panel breaks be careful of being

injured by broken glass.

Television Antenna Connection Protection

Important Information

External Television Antenna Grounding

If an outside antenna or cable sy

stem is to be connected to the TV, make sure that the antenna or

cable system is electrically grounded to provide some protection against voltage surges and

static charges. Article 810 of the National Electrical Code, ANSI/NFPSA 70, provides

information with regard to proper grounding of the mast and supporting structure, grounding of

the lead-in wire to an antenna discharge unit, size of the grounding conductors, location of

antenna discharge unit, connection to grounding electrodes, and requirements of the grounding

electrode.

Lightning Protection

For added protection of the TV during a lightning storm or when it is left unattended or unused

for long periods of time, unplug the TV from the wall outlet and disconnect the antenna or cable

system.

Power Lines

Do not locate the antenna near overhead light or power circuits, or where it could fall into such

power lines or circuits.

7

Installing Batteries to the Remote Control

Please insert two AAA batteries into the remote control. Make sure that you match the (+)

and (-) symbols on the batteries with the (+) and (-) symbols inside the battery compartment.

Afterwards, re-attach the battery cover.

Please note:

Only use AAA batteries.

Do not mix new and old batteries. This may result in cracking or leakage that may pose a

fire risk or lead to personal injury.

Inserting the batteries incorrectly may also result in cracking or leakage that may pose a

fire risk or lead to personal injury.

Dispose the batteries in accordance with local laws and regulations.

Keep the batteries away from children and pets.

If the remote control is not used for a long time, remove the batteries.

Keep the remote control away from moisture, sunlight, and high temperatures.

8

Attacthing or Removing the Stand

Lay the TV face-down on a flat, cushioned

surface to

avoiddamaging or scratching.

1. Lay the TV face-down on a flat,

cushioned surface to avoid

damaging or scratching.

2. Untighten the 4 pcs screws holding

the stand assembly and remove them.

3. Attach the wall-mount bracket to

the TV using the mounting holes

on the back of the TV. Mount this

TV according to the instructions

included in the wall-mount bracket.

This apparatus is intended to be supported by UL Listed wall mount bracket.

First Step: Assembling stand and stand

column by using M4x10mm x 4 pcs

screws.

Second Step: Lock the stand and stand

column to TV set by M4x14mm X4 pcs

screws.

First Step

Second Step

Attacthing or Removing the Stand

Lay the TV face-down on a flat, cushioned

surface to

avoiddamaging or scratching.

1. Lay the TV face-down on a flat,

cushioned surface to avoid

damaging or scratching.

2. Untighten the 4 pcs screws holding

the stand assembly and remove them.

3. Attach the wall-mount bracket to

the TV using the mounting holes

on the back of the TV. Mount this

TV according to the instructions

included in the wall-mount bracket.

This apparatus is intended to be supported by UL Listed wall mount bracket.

First Step: Assembling stand and stand

column by using M4x10mm x 4 pcs

screws.

Second Step: Lock the stand and stand

column to TV set by M4x14mm X4 pcs

screws.

First Step

Second Step

Front View

Rear View Mounting Pattern

Identifying Front and Rear Panel

INDICATOR LIGHT – The light is red when power is plugged in but the TV is not turned on.

The light turns blue when the TV is turned on. Because of the LED in the panel, the TV

might take 10 – 12 seconds to power on.

REMOTE SENSOR – The remote sensor receives all the commands from the remote control.

9

Mount

ing Specification : mm004 x mm006 using screw size M6. Length of screw should not

exceed 8mm. Please Note : The 8mm length of screw refers to how deep the screw can go

inside the mounting holes. When you’re buying screws, you should add the original 8mm to

the thickness of your mounting plate in order to get the total screw length.

If You Have Digital Cable without Cable Box or Antenna…

Connection Suggestions

1

.

Make

sure the power of HDTV is turned off.

2

.

Connect

the RF cable from your antenna or digital cable to the TV port on the

back of your HDTV.

3

.

T

urn on the HDTV.

4

.

Follow the fi

rst time on screen instructions.

�

Not

all broadcasts are in High Definition (HD). Please refer to your local

broadcasting stations for more information.

�

The

HDTV’s tuner is designed for HDTV therefore requires a stronger signal than

normal TVs. If you cannot achieve that signal level with your antenna or cable, your

HDTV might lose picture or sound.

Please

Note:

10

Connecting DVD Player with Component YPbPr…

1. Make sure the power of HDTV and your DVD player is turned off.

2. Obtain a Component Cable. Connect the green color connector to both your DVD

player and YPbPr’s green connector port on the back of your HDTV.

3. Connect the blue color connector to both your DVD player and YPbPr’s blue

connector port on the back of your HDTV.

4. Connect the red color connector to both your DVD player and YPbPr’s red connector

port on the back of your HDTV.

5. Obtain a RCA Audio Cable. Connect the white color connector to both your DVD

player and YPbPr’s white connector port on the back of your HDTV.

6. Connect the red color connector to both your DVD player and YPbPr’s red connector

port

on the back of your HDTV.

7. Turn on the HDTV and your DVD player.

8. Use the remote control’s source button or the source button on the TV to switch to

YPbPr.

Please Note :

Sometimes DVD players will not automatically output to YPbPr. You will

need to configure your DVD player with AV connection first then switch to

YPbPr. Please reference the DVD player’s manual, to make sure the DVD

player is configured to output correctly to the TV.

This source shares audio jacks with composite video.

11

Connecting Wii™ with Composite…

1. Make sure the power of HDTV and your Wii™ is turned off.

2.

Obtain a Yellow Video Cable. Connect the Yellow Video connector to both your Wii™

and AV’s Yellow Video connector port on the back side of your HDTV.

3. Obtain a RCA Audio Cable. Connect the white color connector to both your Wii™

and AV’s white connector port on the back side of your HDTV.

4. Connect the red color connector to both your Wii™ and AV’s red connector port on the

back side of your HDTV.

5.

Turn on the HDTV and your Wii™.

6.

Use the remote control’s source button or the source button on the TV to switch to AV.

Please Note:

Make sure to read your Wii™ installation guide for further information.

This source shares audio jacks with YPbPr.

12

Connecti

ng Cable or Satellite boxes with HDMI…

1

. Make sure the power of HDTV

and your set-top box is turned off.

2. Connect a HDMI cable to the HDMI output of your set-top box and the other end to

the HDMI port on the back of your HDTV.

3. Turn on the HDTV and your set-top box.

4. Use the remote control’s source button or the source button on the TV to switch to

HDMI.

Please Note:

�

Please

reference the set-top box’s manual, to make sure the set-top box is

configured to output correctly to the TV.

�

HDTV

supports NEC’s universal remote code. Please look up NEC’s

codes in your universal remote’s hand book.

13

C

onnecting to a PC with VGA and 3.5 mm minijack …

1

. Make sure the power of HDTV and your PC is turned off.

2. Obtain a 15-pin D-Sub VGA cable; connect to the VGA output of your PC and the other

end to the VGA port on the back of your HDTV.

3. Obtain a 3.5 mm Mini-jack, connect to the audio out of your PC and the other end to the

VGA Stereo Input port.

4. Turn on the power of the HDTV and your PC.

5. Use the remote control’s source button or the source button on the TV to switch to PC.

6. Change your PC resolution to 1360x768 at 60hz refresh rate.

7. Press MENU to use the OSD’s PICTURE option.

8. Under the PICTURE option select PC Settings.

9. Under PC Settings use AUTO ADJUST to adjust the screen.

Please Note:

� For the best results, please set your PC resolution to 1360x768 at 60 Hz. Please

refer to the PC or graphic card’s manual for further instructions on how to set your

resolution and refresh rate.

� Please refer to your PC manual for video output requirements of the video card.

� The VGA port of the TV features a power saving mode which will automatically

turn off the TV, if there’s no signal provided for more than 5 minutes.

14

Connecting a Digital Audio Receiver with Coaxial...

1.

Make sure the power of HDTV and your receiver is turned off.

2. Obtain a COAXIAL cable, connect it to your receiver’s COAXIAL digital

input and the COAXIAL connection on the LINE OUT port on the back of the

HDTV.

3. Turn on the HDTV and your receiver.

Please Note:

If you want pure digital stream for your receiver to decode, you must also

configure the TV’s OSD Sound->Digital Audio Out function. Make sure the

option is on 5.1CH.

If your receiver is making static noises when receiving 5.1CH, you must use

the PCM option instead.

Please reference the receiver’s manual as well, to make sure the receiver is

configured to receive signals correctly from the TV.

The TV’s COAXIAL out for 5.1CH is ONLY used for antenna/cable

connection. Any other incoming audio signal will be passed out of

COAXIA

L in PCM format.

15

Main unit description

Control Panel Button Function

16

VOL+

:

Increase volume; if OSD is active, functions as right in the menu;

in SOURCE menu, functions as ENTER.

VOL- : Decrease volume; if OSD is active, functions as left in the menu.

CH+ : Change channel up; if OSD is active, functions as up in the menu

CH- :

MENU : Press to select the main menu.

SOURCE : Select the input signal.

POWER : Switch on when at standby mode or enter the standby mode.

Change channel down; if OSD is active, functions as down in

the menu.

TV Terminal Connections

1. EARPHONE out terminal.

2. Coaxial out terminal.

3. Line out terminal.

4. USB input terminal（only for service.）

5. HDMI1 input terminal.

6. HDMI2/MHL input terminal.

7. HDMI3 input terminal.

8. VGA input terminal of simulation signal of PC.

9. PC AUDIO input terminal.

10. RF antenna.

11.Video input terminal.

12. AUDIO input terminal.（Audio input terminal for YPBPR and video）

13. Component input terminal.

Remote control

POWER: Po

w

e

r on/

off b

u

t

on, press once to turn the TV on and press

again to turn the TV off.

MUTE: Press this button to mute or restore sound.

MTS/AUDIO: When stereo program is received, press this key to

switch sound system between mono and stereo.

When SAP program is received, press this button to switch sound

system between mono and SAP

When stereo and SAP program is received, press this key to switch

among mono, stereo and SAP.

Press this key to show the list of audio languages available for the

current channel in ATSC.

ASPECT: Press to

adjust picture ratio.

PMODE: Select picture mode.

SMODE: Select sound mode.

0-9: Select and switch to a channel using 0 - 9.

-/--:

Switch the program digit.

: Switch back and front between the current and previous channels.

DISPLAY: Display TV information.

EPG：

Enter electronic program guide

AUTO

.elbaliava ton is tI :

RED, GREEN, YELLOW, CYAN:

Thi

s

button is not available.

SLEEP: Se

t t

h

e sl

ee

p t

i

m

er.

SOURCE: Press to change signal source.

ENTER: Enter the selected option or perform the selected operation.

MENU: Press this button to enter the main menu.

EXIT: Exit the OSD (On-screen display).

CH+/CH-: Change the channel.

CC: Press this key to select the CC ,ON or OFF mode and CC on Mute .

INFO: Display some informat

ion of current program in TV mode.

VOL+/VOL-: Adjust the volume.

FAV: Swi

tch betw

een custom set "Favorite List"

F.LIST: Press this key to display the Favorite List mode.

C.LIST: Press this key to display the channel list mode.

SOURCE

DISPLAY

CH

FAV

INFO

CC

MTS

F. LIST C. LIST

AUTOSMODEPMODE

ASPECT

SLEEPEPG

ENTER

MENU

Installation Guide

Press MENU butto

n to display the MAIN OSD MENU; Press ◄ / ►button to select the

MENU you want; Press ENTER button to enter the sub menu; Press ▼ / ▲ button to select the

option and then press ◄ / ► to adjust the value in the sub menu; You can press MENU button to

go back to the upper menu or EXIT button to close the OSD.

PICTURE

You c

an select the type of picture, which best corresponds to your viewing. Press the “MENU”

button to enter the OSD menu .Then

press “/” button to select the

“PICTURE” menu.

1. Press “” button to select “Picture

Mode”, press “

/

” but

ton to select.

2. Press “/” button to select

“Brightness” and press the “/”

button to enter brightness adjustment

menu to adjust brightness.

3. Press “/” button to select

“Contrast” and press the “/” button

to enter contrast adjustment menu to

adjust contrast.

4. Press “/” button to select “Color” and press the “/” button to enter color adjustment

menu to adjust color.

5. Press “/” button to select “Tint” and press the “/” button to enter hue adjustment menu

to adjust tint.

Note:

The 'Tint' item is used in NTSC mode only

.

6. Press “/” butto

n to select “Sharpness” and press the “/” button to enter sharpness

adjustment menu to adjust sharpness.

7. Press “/” button to select “Color Temperature” and press the “/” button to select.

8. Press “/” button to select “Advanced Setting” and press the “ENTER/” button to enter

sub-menu.

a. Press “/” button to

“Aspect Ratio” and

“ /” button to

select.

b. Press “/” button to

“Noise Reduction”

and press the

button to select.

c. Press “/” button to

“Dynamic Contrast”

and press the

button to select “On” or

“Off”.

SOUND

You can select the type of sound, which best corresponds to your listening.

Press the

“MEN

U” button

to enter the OSD

menu .Then

press “/”

button to select

the “SOUND”

menu.

1. Press “”

button to

select

“Equalizer

Settings”

and press

the

“ENTER/” button to enter sub-menu.

a. Press “/” button to select “Equalizer Mode”. Press “/” button to select.

b. Press “/” button to select “150Hz”. Press “/” button to select.

c. Press “/” button to select “500 Hz”. Press “/” button to select.

d. Press “/” button to select “1K Hz”. Press

“/” button to select.

e. Press “/” button to select “5K Hz”.

Press“/” button to select.

f. Press “/” button to select “10K Hz”.

Press “/” button to select

g. Press “/” button to select “Balance”.

Press “/” button to select

sele

ct

press the

select

“/”

select

“ /”

La pagina sta caricando ...

Sylvania SLED5516A Manuale del proprietario

Sylvania SLED5516A Manuale del proprietario

in altre lingue

Altri documenti