Salter SA TE-250 Manuale del proprietario

TE-250-EU

INFRARED THERMOMETER

Instructions and Guarantee

This equipment needs to be installed and put into service in accordance

with the information provided in this manual

2 | GB

GB | 3

INTRODUCTION

Utilising infrared technology, this thermometer takes temperatures in seconds by

measuring heat generated by the surface skin of the forehead or other objects. This

product conforms to the provisions of the EC directive MDD(93/42/EEC). Its advantages

include:

1. 6 in 1 functions

Human Body/Object/Night Mode Option/Fever Alarm/30 User Memory/Backlight

2. Night Mode Option

Switch to Night mode to reduce the interference of buzzer during your baby

sleeping.

3. Red LED Light for Fever Alarm

This device has the LED light to remind user their readings are over 38°C and plus

the beep sound only in Human Body Mode.

4. 30 User Memory

5. Illuminated Backlight Display

6. C/°F Switch-able Function

7. One-second reading

8. Auto power o for power saving

9. Low-battery Indicator

10. Large LCD Display

11. Economic design and convenience:

This is a “Non-contact” medical thermometer that enables temperature readings,

designed for sanitary conditions, cleanliness, and convenience. Simply move the

thermometer close to the subject’s forehead or object at the distance indicated

by the device.

12. Instant Measurement

By using our unique technology, users can get their precise body temperature

instantly and accurate.

IMPORTANT INFORMATION BEFORE USE

When using this product, please be sure to follow all the notes listed below. Any action

against these notices may cause injury or aect the accuracy.

2 | GB

GB | 3

1. Do not disassemble, repair, or remodel the thermometer.

2. Be sure to clean the thermometer lens each time after usage.

3. Avoid direct ﬁnger contact with the lens.

4. No modiﬁcation of this equipment is allowed.

5. It is recommended that user may take 3 temperatures. If they are dierent, use

the highest reading.

6. Do not expose the thermometer to extreme temperature, very high humidity, or

direct sunlight.

7. Avoid extreme shock or dropping the device.

8. Before the measurement, users and thermometer should stay in steady state room

condition for at least 30 minutes.

9. Avoid measuring temperature for 30 minutes after exercise, bathing, or returning

from outdoors.

10. To protect the environment, dispose of empty batteries at appropriate collection

sites according to national or local regulations.

11. It is ill-advised to disassemble the thermometer.

12. Please use the thermometer solely for its intended purpose.

13. Carefully hold the device when in use to avoid dropping the device.

14. Allow one minute between successive measurements as slight variations may

occur if measurements are taken over a short period of time. Use average

temperatures instead.

15. There are no absolute body temperature standards. Keep reliable records of your

personal temperature to serve as a reference for judging a fever.

16. Under any circumstances, the temperature taking result is ONLY for reference.

Before taking any medical action, please consult your doctor.

BATTERY INSTALLATION

Low battery warning

When the battery power becomes low, the low battery symbol will appear on the

display. The thermometer can still be used during this time, but the batteries should

be replaced as soon as possible. If the batteries run out completely, “Lo” will

be displayed along with the low battery symbol. In this case, the batteries will need to

be replaced before using the thermometer again.

4 | GB

GB | 5

Replacing the Battery

1. Gently slide the battery cover back.

2. Carefully remove the old batteries and

properly discard.

3. Insert new batteries (Two 1.5V alkaline

AAA Size) according to the proper polarity.

4. Slide the battery cover back on.

Note

• It is recommended to remove the batteries

if the unit will not be used for an extended

period of time.

• Please store batteries away from small children and heat.

• Do not use rechargeable batteries.

• Dispose of used batteries in accordance with the applicable legal regulations.

• Never dispose of batteries in the normal household waste.

Scan in progress

PRODUCT IDENTIFICATION

Memory

Recall

button

Battery

compartment

lid

LCD display

Power /

scan & measure

Button

Human/Object

Button

Red LED Light

for Fever Alarm

(Only in Human

Mode)

Measurement sensor

Buzzer

4 | GB

GB | 5

DESCRIPTION OF LCD DISPLAY

SWITCHING BETWEEN CELCIUS OR FAHRENHEIT

Your thermometer can display results in either degrees Celsius (°C) or

degrees Fahrenheit (°F).

To switch between Celsius and Fahrenheit, while the unit is on press

and hold both the Human/Object button and the Memory button for

approximately 3 seconds. This will change the mode to either °C or °F.

Once the thermometer beeps, at which time the mode

has been changed and you may release the buttons.

Switching between 4 Kinds of Scan Mode

1. Under power on status, you can press the Human/Object button

to switch dierent scan mode. There are 4 kinds of mode which including Human,

Object, Human/Night, and Object/Night mode (in order).

2. The beep sounds will be closed when your choice in Human/Night mode, and

Object/Night mode, and the Moon symbol will appears on the LCD in both Night

mode.

Temperature in degrees

Celcius scale

Fahrenheit scale

Scan in progress

Frowning face

Measurement

≥38.0°C(≥ 100.4°F)

Fever

Smiling face

Measurement

<38.0°C(< 100.4°F)

No Fever

Low battery warning

Memory symbol

and sets of

records

Night mode

Human scan mode

Object scan mode

0. 5~ 3 cm

6 | GB

GB | 7

Human mode Object mode Human mode

& night mode

Object mode

& night mode

Note

Each press will comes with a beep sound to ensure the setting is activated. (Except both

Night modes)

0. 5~ 3 cm

TIPS FOR MEASURING HUMAN TEMPERATURE

Bear in mind that the thermometer needs to have been in the room in which the

measurement is taken for at least 30 minutes before use.

• Attempting to take temperature readings from sites on the body other than the

forehead may produce inaccurate results.

• The patient should remain still while the reading is being taken.

• Infrared forehead temperature readings are equivalent to oral temperature readings.

In all of these cases, please consult your doctor.

• Readings taken while asleep should not be compared directly to readings taken while

awake, as body temperature while asleep is typically lower.

• Do not take body temperature readings within 30 minutes of being outdoors,

exercising or bathing.

MEASURING HUMAN TEMPERATURE

1. Press the Power button to turn the thermometer on. The unit will

run a self-test and all symbols on the display will momentarily

appear.

2. Ensure that the thermometer is in Human mode; the Human

symbol will be on the display. To alternate between modes press

and release the Human/Object Mode button until you see the

desired measurement symbol on the display.

3. Press and hold the “Scan & measure button”, aiming the

0. 5~ 3 cm

6 | GB

GB | 7

Measurement Sensor at the person’s

forehead, holding the thermometer

approximately 0.5~3 cm. But don’t touch

the forehead.

4. Release the “Scan & measure button”.

In about a second, you will hear a short beep means this temperature reading has

been completed and accompany with a back-light.

5. If the temperature measurement is below 38°C, a “Smiling Face”

will be

appear next to the reading. If the reading is 38°C or above, a “Frowning Face”

will be displayed and the RED LED light up.

Fever Alarm - Only in Human Mode and Human/Night Mode

6. After about 30 seconds after use, the thermometer will automatically beep and

shut o.

MEASURING OBJECT TEMPERATURE

1. Press the Power button to turn the thermometer on.

All symbols on the display will momentarily appear.

2. Ensure that the thermometer is in Object mode; the

Object symbol will be on the display. To alternate

between modes press and release the Human/

Object Mode button until you see the desired

measurement symbol on the display.

3. Press and hold the “Scan & measure button”,

aiming the Measurement Sensor at the object,

holding the thermometer approximately

0.5~3 cm.

4. Release the “Scan & measure button” and the

temperature reading will be displayed.

5. After about 30 seconds after use, the thermometer will automatically beep and

shut o.

MEMORY FUNCTION

You can recall up to 30 stored measurements in memory to share with your doctor or

trained healthcare professional.

0. 5~ 3 cm

0.5 ~3 cm

0. 5~ 3 cm

8 | GB

GB | 9

Memory Recall button.

1. When the device is on, press once brieﬂy on the “MEM button”, then pass it again

to show the last measurement accompanied by symbol.

2. The symbol or symbol will appear with each measurement stored in

memory to indicate whether a person or object temperature was taken.

3. Each press of the same button recalls a previous measurement, so then all

the way to . Continue to press the Memory Recall button button to view the

next previously stored measurement.

4. Any new measurement will be recorded and the oldest memory deleted without

you having to do anything.

Memory Deletion

1. Under power on status, you may keep press MEM Button for more than 3 seconds

to delete all the readings.

2. You will see “--” on display and “sound four short beeps”, that mean all the

memories are cleared.

3. Automatically on the 31th measurement: when the 30 memories have been used

up, any new measurement will be recorded with and the oldest memory

deleted without you having to do anything.

All the readings will be cleared no matter record in Human mode or Object mode.

CLEANING AND DISINFECTING

Lens/ Measurement Sensor

Gently clean with an alcohol swab.

Do not use water to wash the thermometer lens directly.

Thermometer

Clean with a soft, dry cloth.

Do not use water to rinse the device.

8 | GB

GB | 9

APPLIED STANDARDS

This product conforms to the provisions of the EC directive MDD(93/ 42/ EEC). The

following standards apply to design and/or manufacture of the products:

• ASTM E1965-98

Standard Speciﬁcation for Infrared Thermometers for Intermittent Determination of

Patient Temperature.

• ISO 14971

Medical devices-Application of risk management to medical devices. The

Classiﬁcation according to IEC/EN60601-1 sub-clauses 5:

ERROR CODES

When a malfunction or incorrect temperature measurement occurs, an error message will

appear as described below.

LCD Display Cause Solution

The temperature measured

is higher than

Human thermometer mode:

43°C (109.4°F)

Object temperature mode:

100°C (212.0°F)

Operate the thermometer only

between the speciﬁed temperature

ranges. If necessary, clean the

sensor tip. In the event of a

repeated error message, contact

your retailer or Customer Services.

The temperature measured

is lower than

Human thermometer mode:

34°C (93.2°F)

Object temperature mode:

0°C (32.0°F)

The operating temperature is

not in the range 16°C~40°C

(60.8°F~104°F)

Operate the thermometer only

between the speciﬁed temperature

ranges.

10 | GB

GB | 11

TECHNICAL SPECIFICATION

• Measuring range:

Human Body: 34°C ~43°C (93.2°F ~ 109.4°F)

Object: 0°C~100°C (32.0°F~212.0°F)

• Calibration Accuracy:

Human Body:

±0.2°C(±0.4°F): from 34°C ~43°C (93.2°F ~ 109.4°F)

Object:

<LESS THAN EQUAL TO>40°C : ± 2°C

> 40°C : ± 5%

• Power supply: 2 x 1.5V AAA size alkaline batteries

• Dimensions: approx. 128.5mm×48.83mm×38.85mm (L×W×H)

• Weight : approx. 80g (with batteries)

• Operation Distance : 0.5~3 cm

EXPLANATION OF SYMBOLS

SGS No.

Refer to instructions

Type BF equipment (Sensor)

Disposal information: Should you wish to dispose of the article, do so in accordance

with current regulations. Details are available from your local authority

Manufacturer’s name and address

European Authorized Representative

10 | GB

GB | 11

EMC TABLES

Guidance and manufacturer’s declaration-electromagnetic emissions

The Ear Thermometer is intended for use in the electromagnetic environment

speciﬁed below. The customer or the user of the Thermometer should assure that it is

used in such an environment.

Emissions test Compliance

Electromagnetic environment

guidance

RF emissions CISPR 11 Group 1

The Thermometer uses RF energy

only for its internal function.

Therefore, its RF emissions are very

low and are not likely to cause any

interference in nearby electronic

equipment.

RF emissions CISPR 11 Class B

The Thermometer is suitable for

use in all establishments other

that domestic and those directly

connected to the public low-voltage

power supply network that supplies

buildings used for domestic

purposes.

Harmonic emissions

IEC 61000-3-2

Not applicable

Voltage ﬂuctuations

Flicker emissions

IEC 61000-3-3

Not applicable

12 | GB

GB | 13

Guidance and manufacturer’s declaration-electromagnetic immunity

The Thermometer is intended for use in the electromagnetic environment speciﬁed below. The

customer or the user of the Thermometer should assure that it is used in such an environment.

Immunity test IEC 60601 test level

Compliance

level

Electromagnetic environment-

guidance

Electrostatic

discharge (ESD)

IEC 61000-4-2

±6kV contact

±8kV air

±6kV

contact

±8kV air

Floor should be wood, concrete or

ceramic tile. If ﬂoors are covered

with shythetic material, the relative

humidity should be at least 30%.

Power frequency

(50/60 Hz)

magnetic ﬁeld

IEC 61000-4-8

3 A/m 3A/m

Power frequency magnetic ﬁelds

should be at levels characteristic

of a typical location in a typical

commercial or hospital environment.

12 | GB

GB | 13

Guidance and manufacturer’s declaration-electromagnetic immunity

The Thermometer is intended for use in the electromagnetic environment speciﬁed below. The

customer or the user of the Thermometer should assure that it is used in such an environment.

Immunity test

IEC 60601

test level

Compliance

level

Electromagnetic environment-guidance

Conducted RF

IEC 61000-4-6

Radiated RF

IEC 61000-4-3

3Vrms

150kHz to

80 MHz

3V/m

80MHz to

2.5 GHz

3 Vrms

3 V/m

Portable and mobile RF communications

equipment should be used no closer to any

part of the Ear Thermometer, including cables,

than the recommended separation distance

calculated from the equation applicable to the

frequency of the transmitter.

Recommended separation distance.

d=1.2

d=1.2 80 MHz to 800 MHZ

d=2.3 800 MHz to 2,5 Ghz

where P is the maximum output power rating

of the transmitter in watts (W) according

to the transmitter manufacturer and d is

the recommended separation distance in

meters (m).

Field strengths from ﬁxed RF transmitters, as

determined by an electromagnetic site survey,”

should be less than the compliance level in

each frequency range.” Interference may occur

in the vicinity of equipment marked with the

following symbol:

NOTE 1 At 80 MHz and 800 MHz, the higher frequency range applies.

NOTE 2 These guidelines may not apply in all situations. Electromagnetic propagation is aected by absorption and

reﬂection from structures, objects and people.

Field strengths from ﬁxed transmitters, such as base stations from radio (cellular/cordless) telephones and land

mobile radios, amateur radio, AM and FM radio broadcast and TV broadcast can not be predicted theoretic call with

accuracy. To assess the electromagnetic environment due to ﬁxed RF transmitters, an electromagnetic site survey

should be considered. If the measured ﬁeld strength in the location in which the Ear Thermometer is used exceeds

the applicable RF compliance level above, the Ear Thermometer should be observed to verify normal operation. If

abnormal performance is observed, additional measures may be necessary, such as reorienting or relocating the Ear

Thermometer. Over the frequency range 150kHz to 80MHz, ﬁeld strengths should be less than [V1] V/m.

14 | GB

Recommended separation distances between portable and mobile RF communications equipment

and the Thermometer

The Thermometer is intended for use in an electromagnetic environment in which radiated

RF distances are controlled. The customer or the user of the Thermometer can help prevent

electromagnetic interference by maintaining a minimum distance between portable and mobile

RF communications equipment (transmitters) and the Thermometer as recommended below

according to the maximum output power of the communications equipment.

Rated maximum

output power of

transmitter / W

Separation distance according to frequency of transmitter / m

150 kHz to 80 MHZ

d=1.2

80 MHz to 800 MHZ

d=1.2

800 MHz to 2.5 GHz

d=2.3

0.01 0.12 0.12 0.23

0.1 0.38 0.38 0.73

1 1.2 1.2 2.3

10 3.8 3.8 7.3

100 12 12 23

2 YEAR GUARANTEE

FKA Brands Ltd guarantees this product from defect in material and workmanship for a period of

2 years from the date of purchase, except as noted below. This FKA Brands Ltd product guarantee

does not cover damage caused by misuse or abuse; accident; the attachment of any unauthorised

accessory; alteration to the product; or any other conditions whatsoever that are beyond the control

of FKA Brands Ltd. This guarantee is eective only if the product is purchased and operated in the

UK / EU. A product that requires modiﬁcation or adaptation to enable it to operate in any country

other than the country for which it was designed, manufactured, approved and / or authorised,

or repair of products damaged by these modiﬁcations is not covered under this guarantee. FKA

Brands Ltd shall not be responsible for any type of incidental, consequential or special damages.

To obtain guarantee service on your product, return the product post-paid to your local service

centre along with your dated sales receipt (as proof of purchase).

Upon receipt, FKA Brands Ltd will repair or replace, as appropriate, your product and return it to you,

post-paid. Guarantee is solely through HoMedics Service Centre. Service of this product by anyone

other than the Salter Service Centre voids the guarantee.

This guarantee does not aect your statutory rights.

For your local Salter Service Centre, go to www.salterhousewares.co.uk/servicecentres

F | 15

14 | GB

F | 15

PRÉSENTATION

En utilisant la technologie infrarouge, ce thermomètre prend la température en

quelques secondes. Il mesure la chaleur générée par la peau du front ou par un objet.

Ce produit est conforme aux dispositions contenues dans la directive de l’UE relative

aux dispositifs médicaux 93/42/CEE. Les avantages :

1. 6 fonctions en 1

Corps humain/Objet/Option mode nuit/Alarme ﬁèvre/Mémoire utilisateur 30/

Rétroéclairage

2. Option mode nuit

Passez en mode nuit pour réduire les interférences de l’avertisseur pendant le

sommeil de votre bébé.

3. Voyant LED rouge pour alerter en cas de ﬁèvre

Cet appareil possède une lumière LED pour rappeler à l’utilisateur que ses lectures

sont supérieures à 38° C ainsi qu’un bip sonore, disponible uniquement en mode

corps humain.

4. Mémoire utilisateur 30

5. Achage rétro-éclairé

6. Fonction de basculement C/°F

7. Résultat du relevé de sonde en une seconde

8. Mise en marche/arrêt automatique pour une économie d’énergie

9. Voyant indicateur de pile faible

10. Grand écran LCD

11. Conception simple et pratique :

Il s’agit d’un thermomètre médical « sans contact » qui permet des relevés

de température. Conçu pour des raisons sanitaires et de praticité. Rapprochez

simplement le thermomètre du front ou de l’objet du sujet en respectant la

distance indiquée par l’appareil.

12. Mesure instantanée

En utilisant notre technologie unique, les utilisateurs peuvent obtenir leur

température corporelle précise instantanément et avec précision.

INFORMATIONS IMPORTANTES AVANT UTILISATION

Lors de l’utilisation de ce produit, s’assurer de suivre toutes les indications fournies

ci-dessous. Tout non-respect de ces avis peut entraîner des blessures ou aecter la

précision de l’appareil.

16 | F

1. Ne pas démonter, réparer ou altérer le thermomètre.

2. Il convient de nettoyer la lentille du thermomètre après chaque utilisation.

3. Éviter tout contact direct des doigts sur la lentille.

4. Aucune modiﬁcation de cet équipement n’est autorisée.

5. Nous conseillons d’eectuer 3 relevés de température. En cas de divergence entre

ces relevés, retenez la mesure la plus élevée.

6. Ne pas exposer le thermomètre à des températures extrêmes, à une forte humidité

ou à la lumière directe du soleil.

7. Éviter tout choc violent ou de faire tomber le thermomètre.

8. Avant d’eectuer un relevé, l’utilisateur et le thermomètre doivent rester dans une

pièce à une température ambiante constante pendant au moins 30 minutes.

9. Éviter de relever la température dans les 30 minutes qui suivent toute activité

physique, après avoir pris un bain ou être sorti(e).

10. Dans un souci de protection de l’environnement, jeter les piles usagées dans

un site une collecte de déchets appropriée conformément aux règlementations

locales ou nationales.

11. Il est déconseillé de démonter le thermomètre.

12. Veuillez utiliser le thermomètre uniquement aux ﬁns pour lesquelles il a été

conçu.

13. Tenir le thermomètre avec précaution pendant son utilisation pour éviter de le

faire tomber.

14. Laisser une minute entre chaque relevé consécutif car de légères variations

peuvent se produire si les mesures sont réalisées sur une courte période. Utiliser

plutôt une température moyenne.

15. Il n’y a pas de normes de température corporelle absolues. Conserver des relevés

ﬁables de votre température corporelle à titre de référence pour déterminer si

vous avez de la ﬁèvre.

16. Le relevé de température est fourni UNIQUEMENT à titre indicatif. Avant de prendre

toute mesure médicale, veuillez consulter votre médecin.

INSTALLATION DE LA PILE

Voyant indicateur de pile faible

Lorsque la charge de la batterie devient faible, le symbole de batterie faible

apparaît à l’écran. Le thermomètre peut toujours être utilisé pendant cette

période, mais les piles doivent être remplacées dès que possible. Si les piles sont

complètement déchargées, « Lo » s’ache, accompagné du symbole de pile faible.

F | 17

16 | F

IDENTIFICATION DU PRODUIT

Bouton

de

mémoire

Couvercle du

compartiment

à pile

Écran LCD

Bouton

d’alimentation/

scan & mesure

Bouton

humain/

objet

Voyant LED

rouge pour

alerter en cas

de ﬁèvre

(Uniquement

disponible en

mode humain)

Sonde de mesure

Avertisseur

F | 17

Dans ce cas, les piles devront être remplacées avant que le thermomètre ne puisse

être réutilisé.

Changer la pile

1. Faites glisser doucement le couvercle des piles vers l’arrière.

2. Retirez soigneusement les anciennes piles et jetez-les correctement.

3. Insérez de nouvelles piles (deux piles alcalines AAA de 1,5 V) selon la polarité

appropriée.

4. Remettez le couvercle de la batterie en place.

REMARQUE :

• Il est recommandé d’enlever la pile en cas de non utilisation du thermomètre pendant

une période prolongée.

• Conserver la pile hors de portée des jeunes enfants et de la chaleur.

• Ne pas utiliser de piles rechargeables.

• Jeter les piles usagées conformément à toutes les réglementations applicables en

vigueur. Ne jamais jeter les piles avec les ordures ménagères.

18 | F

BASCULEMENT ENTRE CELSIUS OU FAHRENHEIT

Votre thermomètre peut acher les résultats en degrés Celsius (°C) ou

en degrés Fahrenheit (°F).

Pour basculer entre Celsius et Fahrenheit, pendant que l’appareil est

allumé, maintenez enfoncés le bouton Humain/Objet et le bouton

Mémoire pendant environ 3 secondes. De cette façon, vous passerez

en mode °C ou °F. Une fois que le thermomètre aura émis un bip, cela

signiﬁe que le mode a été modiﬁé et vous pouvez relâcher les boutons.

Basculer entre 4 types de scans possibles

1. Lorsque l’appareil est allumé, vous pouvez appuyer sur le bouton

Humain/Objet pour changer les diérents modes de scan. Il existe 4 modes :

Humain, Objet, Humain/Nuit et Objet/Nuit (dans l’ordre).

2. Les bips sonores seront désactivés lorsque vous choisirez le mode humain/nuit

et le mode objet/nuit, et le symbole d’une lune apparaîtra sur l’écran LCD pour les

deux modes nuit.

F | 19

DESCRIPTION DE L’ÉCRAN D’AFFICHAGE

Température en degrés

Échelle Celsius

Échelle Fahrenheit

Relevé en cours

Visage froncé

Relevé

≥38.0°C(≥ 100.4°F)

Fièvre

Visage souriant

Relevé

<38.0°C(< 100.4°F)

Pas de ﬁèvre

Voyant indicateur de

pile faible

Symbole de

mémoire et jeux

d’enregistrements

Mode nuit

Mode scan humain

Mode scan objet

0. 5~ 3 cm

18 | F

F | 19

Mode humain Mode objet Mode humain &

mode nuit

Mode objet &

mode nuit

Remarque

Chaque pression sera accompagnée d’un bip pour activer le réglage. (Sauf pour les deux

modes nuit)

0. 5~ 3 cm

CONSEILS POUR RELEVER LA TEMPÉRATURE CORPORELLE HUMAINE

N’oubliez pas que le thermomètre doit être resté dans la pièce dans laquelle le relevé

sera eectué pendant au moins 30 minutes avant son utilisation.

• Tenter de prendre des relevés de température sur d’autres parties du corps que le

front peut produire des résultats inexacts.

• Le patient doit rester immobile pendant le relevé de température.

• Les relevés de température frontale infrarouge sont équivalents aux relevés de

température buccale. Dans chacun de ces cas, veuillez consulter votre médecin.

• Les relevés pris pendant le sommeil ne doivent pas être comparés directement aux

relevés pris pendant le réveil, car la température corporelle pendant le sommeil est

généralement plus basse.

• Ne prenez pas de relevés de température corporelle dans les 30 minutes qui suivent

une sortie extérieure, une séance d’exercices physiques ou un bain.

PRISE DE TEMPÉRATURE CORPORELLE HUMAINE

1. Appuyez sur le bouton d’alimentation pour allumer le

thermomètre. L’unité exécutera un auto-test et tous les symboles

sur l’écran apparaîtront momentanément.

2. Assurez-vous que le thermomètre est en mode humain ; le

symbole humain sera aché. Pour alterner entre les modes,

appuyez et relâchez le bouton mode humain/objet jusqu’à ce que

le symbole de mesure souhaité s’ache à l’écran.

3. Appuyez et maintenez enfoncé le “bouton Scan & Mesure”, en

Température en degrés

Mode scan objet

0. 5~ 3 cm

20 | F

orientant le capteur de mesure vers

le front de la personne, en tenant le

thermomètre à environ 0,5~3 cm. Mais

ne touchez pas le front.

4. Relâchez le «bouton Scan & Mesure».

Dans environ une seconde, vous entendrez un bref bip, ce qui signiﬁe que cette

lecture de température est terminée et s’accompagne d’un rétro-éclairage.

5. Si la mesure de température est inférieure à 38°C, un visage souriant

s’ache

à côté de la mesure. Si la mesure de température est égale ou supérieure à 38°C,

un visage mécontent s’ache.

Alarme de ﬁèvre - Uniquement en mode humain et en mode humain/nuit

6. Environ 30 secondes après utilisation, le thermomètre émet automatiquement un

bip et s’éteint.

PRISE DE TEMPÉRATURE D’UN OBJET

1. Appuyez sur le bouton d’alimentation pour allumer

le thermomètre. Tous les symboles sur l’écran

apparaîtront momentanément.

2. Assurez-vous que le thermomètre est en mode objet

; le symbole objet sera aché. Pour alterner

entre les modes, appuyez et relâchez le bouton

mode humain/objet jusqu’à ce que le symbole de

mesure souhaité s’ache à l’écran.

3. Appuyez et maintenez enfoncé le “bouton Scan &

Mesure”, en orientant le capteur de mesure vers

le front de la personne, en tenant le thermomètre

à environ 0,5~3 cm.

4. Relâchez le « bouton Scan & Mesure » et la lecture de la température sera achée.

5. Environ 30 secondes après utilisation, le thermomètre émet automatiquement un

bip et s’éteint.

FONCTION DE MÉMOIRE

Vous pouvez rappeler jusqu’à 30 mesures en mémoire à partager avec votre médecin ou

un professionnel de santé compétent.

0. 5~ 3 cm

0.5 ~3 cm

0. 5~ 3 cm

F | 21

0. 5~ 3 cm

La pagina sta caricando ...

Salter SA TE-250 Manuale del proprietario

Salter SA TE-250 Manuale del proprietario

in altre lingue

Documenti correlati

Altri documenti