Salter TE-150-EU Manuale del proprietario

Marca: Salter

Modello: TE-150-EU

Categoria: Termometri digitali per il corpo

Tipo: Manuale del proprietario

Questo manuale è adatto anche per

SA TE-150

TE-150-EU

INFRARED EAR THERMOMETER

Instructions and Guarantee

This equipment needs to be installed and put into service in accordance

with the information provided in this manual

2 | GB

GB | 3

INTRODUCTION

This Thermometer is intended to be used as the intermittent measurement of human

body temperature for people of all ages in the home environment.

Utilizing infrared technology, this thermometer takes temperatures in seconds by

measuring heat generated by the ear. This product conforms to the provisions of the EC

directive MDD(93/42/EEC). Its advantages include:

1. Ear measurement

2. Probe cover not required

3. Waterproof probe design

4. One-second reading

5. Auto power o for power saving

6. Low-battery Indicator

7. Warning indication - indications for battery condition and measuring range.

8. Jumbo LCD Display

9. Memory function

IMPORTANT INFORMATION BEFORE USE

When using this product, please be sure to follow all the notes listed below. Any action

against these notices may cause injury or aect the accuracy.

1. Do not disassemble, repair, or remodel the thermometer.

2. Be sure to clean the thermometer lens each time after usage.

3. Avoid direct ﬁnger contact with the lens.

4. No modiﬁcation of this equipment is allowed.

5. It is recommended that user may take 3 temperatures. If they are dierent, use

the highest reading.

6. Do not expose the thermometer to extreme temperature, very high humidity, or

direct sunlight.

7. Avoid extreme shock or dropping the device.

8. Before the measurement, users and thermometer should stay in steady state room

condition for at least 30 minutes.

9. Avoid measuring temperature for 30 minutes after exercise, bathing, or returning

from outdoors.

Probe tip

2 | GB

GB | 3

10. To protect the environment, dispose of empty batteries at appropriate collection

sites according to national or local regulations.

11. It is ill-advised to disassemble the thermometer.

12. Please use the thermometer solely for its intended purpose.

13. Carefully hold the device when in use to avoid dropping the device.

14. Allow one minute between successive measurements as slight variations may

occur if measurements are taken over a short period of time. Use average

temperatures instead.

15. There are no absolute body temperature standards. Keep reliable records of your

personal temperature to serve as a reference for judging a fever.

16. Under any circumstances, the temperature taking result is ONLY for reference.

Before taking any medical action, please consult your doctor.

17. It is recommended calibrate the device every 1 year.

PRODUCT IDENTIFICATION

Memory Recall button

Battery compartment

lid

Probe tip

Power & Measure

button

LCD display

4 | GB

GB | 5

DESCRIPTION OF LCD DISPLAY

TIPS FOR MEASURING HUMAN TEMPERATURE

Bear in mind that the thermometer needs to have been in the room in which the

measurement is taken for at least 30 minutes before use.

NOTE:

• Some people produce dierent readings in their left and right ear. In order to record

temperature changes, always measure a person’s temperature in the same ear.

• The ear thermometer may be used by children only under adult supervision.

Measurement is usually possible over the age of 6 months. In infants under 6 months,

the ear canal is still very narrow so the temperature of the eardrum often cannot be

recorded and the result displayed is often too low.

• The measurement must not be taken in an ear aected by inﬂammatory diseases

(e.g. discharging pus or secretion), after possible ear injuries (e.g. eardrum damage)

or in the healing period after operative procedures. In all of these cases, please

consult your doctor.

• Use of the thermometer on dierent persons can be inappropriate in the event of

certain acute infectious diseases because of the possible spread of germs despite

cleaning and disinfection. If you have any doubts, please consult your doctor.

• This thermometer may only be used without a disposable protective cover.

• If you have been lying on one ear for some time, the temperature is slightly raised.

Wait 60 seconds or measure in the other ear.

• As ear wax can aect the measurement, you should clean the ear before measuring

if necessary.

Temperature in degrees

Celcius scale

Fahrenheit scale

Scan in progressFrowning face

Measurement

≥38.0°C(≥ 100.4°F)

Fever

Smiling face

Measurement

<38.0°C(< 100.4°F)

No Fever

Low battery warning

Memory symbol and sets of records

4 | GB

GB | 5

MEASURING BODY TEMPERATURE IN THE EAR

1. Press the Power & Measure Button for 1 second to switch the thermometer on. All

screen data will display on screen. Then wait for beep sound to let you know the

appliance is ready and followed by last temperature reading.

2. Make sure that the sensor tip and also the ear canal

are clean. As the ear canal is slightly curved, you

have to pull the ear slightly up and backwards before

inserting the sensor tip. This is important so that the

sensor tip can be pointed directly at the eardrum.

Under 1 year

Have child lay ﬂat with the head sideways, so that the ear is facing

upwards. Gently pull the ear straight back.

3. Insert the probe into the ear canal (the probe must insert well to ensure an

accurate temperature measurement), then press the Power & Measure Button for

about 1 second, release the button and you will hear 1 short beep sound means

complete the measurement.

4. You may take out the device to read the measurement result.

5. The backlight display will remain light for approximately 5 seconds each time the

Power & Measure Button is pressed, after each reading is completed, and each

time the Memory button is pressed to recall a previous reading.

6. The thermometer will automatically shut o after one minute without use.

1 year +

Stand behind and slightly to the side of the child/adult. Gently pull the

ear up and back to straighten the ear canal.

6 | GB

GB | 7

Note:

7. To ensure accuracy, please wait at least 1 minute between successive readings.

8. Clean the thermometer lens again after use. After cleaning, wait at least

10 minutes between readings, to ensure accuracy.

CHANGING THE MEASUREMENT UNIT (ºC/ºF)

Changing °C/ °F, please make sure the device is in power on condition. Press the Power &

Measure and Memory Recall buttons together to toggle between °C and °F.

MEMORY FUNCTION

You can recall up to 10 stored measurements in memory to share with your doctor or

trained healthcare professional.

1. Press the Memory Recall button. The ﬁrst

reading displayed is the latest measurement

stored in memory.

2. Continue to press the Memory Recall button

button to view the next previously stored

measurement.

3. Any new measurement will be recorded and the

oldest memory deleted without you having to do

anything.

The readings

If the temperature measurement is below 38°C

(100.4°C), a smiling face will be appear next

to the reading.

If the reading is 38°C (100.4°C) or above, a

frowning face will be displayed.

6 | GB

GB | 7

CLEANING AND DISINFECTING

For home use device disinfection, 70% Ethanol or Isopropyl

alcohol (available in the pharmacy) can be used.

Clean the measuring sensor after each use.

Use a clean cloth or cotton bud that can be moistened with

70 % alcohol.

Lens/ Measurement Sensor

Gently clean with an alcohol swab.

Do not use water to wash the thermometer lens directly.

Thermometer

Clean with a soft, dry cloth.

Do not use water to rinse the device.

APPLIED STANDARDS

This product conforms to the provisions of the EC directive MDD(93/ 42/ EEC).

The following standards apply to design and/or manufacture of the products:

ISO 80601-2-56

Medical electrical equipment -- Part 2-56: Particular requirements for basic safety and

essential performance of clinical thermometers for body temperature measurement

IEC/EN 60601-1

Medical electrical equipment- Part 1: General requirement for safety

IEC/EN 60601-1-2

Medical electrical equipment- Part 2: Collateral standard: Electromagnetic compatibility

- Requirements and tests

IEC/EN 60601-1-11

Medical electrical equipment - Part 1-11: General requirements for basic safety and

essential performance - Collateral standard: Requirements for medical electrical

equipment and medical electrical systems used in the home healthcare environment

8 | GB

GB | 9

BATTERY INSTALLATION

Low battery warning

When the batteries get weak, the battery warning symbol

appears . It is still possible to measure temperature.

The batteries must be replaced. When the battery symbol

ﬂashes and Lo appears in the display, the batteries must be replaced. If the

batteries are too ﬂat, then the thermometer will switch o automatically.

NOTE:

• It is recommended to remove the batteries if the unit will not be used for an extended

period of time.

• Please store batteries away from small children and heat.

• Do not use rechargeable batteries.

• Dispose of used batteries in accordance with the applicable legal regulations.

Never dispose of batteries in the normal household waste.

Replacing the Battery

1. Use a Phillips head screwdriver to loosen battery cover screw. Remove the battery

cover.

2. Remove used battery.

3. Replace with a lithium 3V CR2032 battery in designated area. The + sign on the

battery should be facing upwards.

4. Place the battery cover on the thermometer and tighten the screw to secure it

in place.

8 | GB

GB | 9

CLINICAL ACCURACY VALIDATION METHOD

This device is an adjusted mode clinical thermometer

the validated information for clinical accuracy in each adjusted mode are:

GroupA1: ∆cb=-0.01°C, L

=0.18, δr = ±0.08°C

GroupA2: ∆cb= 0.06°C, L

=0.22, δr = ±0.08°C

GroupB : ∆cb=-0.01°C, L

=0.20, δr = ±0.07°C

GroupC : ∆cb=-0.01°C, L

=0.18, δr = ±0.07°C

∆cb: CLINICAL BIAS

: LlMITS OF AGREEMENT

δr: CLINICAL REPEATABILITY

ERROR CODES

When a malfunction or incorrect temperature measurement occurs, an error message will

appear as described below.

LCD Display Cause Solution

The temperature measured

is lower than 34°C (93.2°F)

Operate the thermometer only

between the speciﬁed temperature

ranges. If necessary, clean the

sensor tip. In the event of a

repeated error message, contact

your retailer or Customer Services.

The temperature measured

is higher than 43°C

(109.4°F)

The operating temperature

is not in the range

15°C~35°C (59°F~95°F)

Operate the thermometer only

between the speciﬁed temperature

ranges.

10 | GB

GB | 11

TECHNICAL SPECIFICATION

• Measuring range:

Human Body: 34°C ~43°C (93.2°F ~ 109.4°F)

• Laboratory Accuracy:

34°C ~43°C±0.2°C (93.2°F ~ 109.4°F ±0.4°F)

• Measuring site: Ear

• Reference body site: Oral

• Calibration Accuracy:

±0.2°C(±0.4°F): from 35°C ~42°C (95°F ~ 107.6°F)

±0.3°C(±0.5°F): out of range

• Display resolution: 0.1°C/°F

• Operating environment:

15°C~35°C (59°F ~ 95°F) with relative humidity up to 95% (non condensing)

• Storage/transportation environment:

-25 to 55 °C(-13 to 131 °F) with relative humidity up to 95% (non condensing)

• Power supply: A lithium 3V CR2032 battery

• Memory: 10 sets

• Weight: approx. 49g (with battery)

• Dimensions: approx. 112.8mm×34.4mm×44.5mm (L×W×H)

• Shelf life: 3 years

EMC TABLES

Medical Electrical Equipment needs special precautions regarding EMC and needs to be

installed and put into service according to the EMC information.

1. Electromagnetic/Radio Frequency Interference (EMC/RFI): Readings may be

aected if the unit is operated within a radio frequency electromagnetic

ﬁeld strength of approximately 3 volts per metre, but the performance of the

instrument will not be permanently aected. Care should be taken to keep the

thermometer at least 15cm/6 inches away from R/C transmitters to avoid radio

frequency interference.

2. Avoid keeping the thermometer too close to objects that continuously generate

high heat (like a hot plate) for long periods of time, which can cause overheating

of the thermometer.

10 | GB

GB | 11

Table 1 For all ME EQUIPMENT and ME SYSTEMS

Guidance and manufacturer’s declaration-electromagnetic emissions

The Ear Thermometer is intended for use in the electromagnetic environment

speciﬁed below. The customer or the user of the Ear Thermometer should assure that

it is used in such an environment.

Emissions test Compliance

Electromagnetic environment

guidance

RF emissions CISPR 11 CISPR 11

The Ear Thermometer uses RF energy

only for its internal function.

Therefore, its RF emissions are very

low and are not likely to cause any

interference in nearby electronic

equipment.

RF emissions CISPR 11 Class B

The Ear Thermometer is suitable

for use in all establishments other

that domestic and those directly

connected to the public low-voltage

power supply network that supplies

buildings used for domestic

purposes.

Harmonic emissions

IEC 61000-3-2

Not applicable

Voltage ﬂuctuations

Flicker emissions

IEC 61000-3-3

Not applicable

12 | GB

GB | 13

Table 2 For all ME EQUIPMENT and ME SYSTEMS

Guidance and manufacturer’s declaration-electromagnetic immunity

The Ear Thermometer is intended for use in the electromagnetic environment speciﬁed below.

The customer or the user of the Ear Thermometer should assure that it is used in such an

environment.

Immunity test IEC 60601 test level

Compliance

level

Electromagnetic environment-

guidance

Electrostatic

discharge (ESD)

IEC 61000-4-2

±6kV contact

±8kV air

±6kV

contact

±8kV air

Floor should be wood, concrete or

ceramic tile. If ﬂoors are covered

with shythetic material, the relative

humidity should be at least 30%.

Electrical fast

transient/burst

IEC 61000-4-4

±2 kV for power

supply lines

±1 kV air for input/

output lines

Not

applicable

Mains power quality should be that

of a typical commercial or hospital

environment.

Surge IEC

61000-4-5

±1kV dierential

mode

±2kV common mode

Not

applicable

Mains power quality should be that

of a typical commercial or hospital

environment.

Voltage

dips, short

interruptions and

voltage variations

on power supply

input lines

IEC 61000-4-11

<5% UT (>95% dip

in UT for 0.5 cycle

40% UT (60% dip in

UT for 5 cycles

70% UT (30% dip in

UT for 25 cycles

5% UT (>95% dip in

UT for 5 sec

Not

applicable

Mains power quality should be that

of a typical commercial or hospital

environment. If the use of the Ear

Thermometer requires continued

operation during power mains

interruptions, it is recommended that

the Ear Thermometer be powered

from an uninterruptible power supply

or a battery.

Power frequency

(50/60 Hz)

magnetic ﬁeld

IEC 61000-4-8

3 A/m 3A/m

Power frequency magnetic ﬁelds

should be at levels characteristic

of a typical location in a typical

commercial or hospital environment.

NOTE UT is the a.c. mains voltage prior to application of the test level.

12 | GB

GB | 13

Table 3 For EQUIPMENT and SYSTEMS that are not LIFE-SUPPORTING

Guidance and manufacturer’s declaration-electromagnetic immunity

The Ear Thermometer is intended for use in the electromagnetic environment speciﬁed below.

The customer or the user of the Ear Thermometer should assure that it is used in such an

environment.

Immunity test

IEC 60601

test level

Compliance

level

Electromagnetic environment-guidance

Conducted RF

IEC 61000-4-6

Radiated RF

IEC 61000-4-3

3Vrms

150kHz to

80 MHz

3V/m

80MHz to

2.5 GHz

3 Vrms

3 V/m

Portable and mobile RF communications

equipment should be used no closer to any

part of the Ear Thermometer, including cables,

than the recommended separation distance

calculated from the equation applicable to the

frequency of the transmitter.

Recommended separation distance.

d=1.2

d=1.2 80 MHz to 800 MHZ

d=2.3 800 MHz to 2,5 Ghz

where P is the maximum output power rating

of the transmitter in watts (W) according

to the transmitter manufacturer and d is

the recommended separation distance in

meters (m).

Field strengths from ﬁxed RF transmitters, as

determined by an electromagnetic site survey,”

should be less than the compliance level in

each frequency range.” Interference may occur

in the vicinity of equipment marked with the

following symbol:

NOTE 1 At 80 MHz and 800 MHz, the higher frequency range applies.

NOTE 2 These guidelines may not apply in all situations. Electromagnetic propagation is aected by absorption and

reﬂection from structures, objects and people.

Field strengths from ﬁxed transmitters, such as base stations from radio (cellular/cordless) telephones and land

mobile radios, amateur radio, AM and FM radio broadcast and TV broadcast can not be predicted theoretic call with

accuracy. To assess the electromagnetic environment due to ﬁxed RF transmitters, an electromagnetic site survey

should be considered. If the measured ﬁeld strength in the location in which the Ear Thermometer is used exceeds

the applicable RF compliance level above, the Ear Thermometer should be observed to verify normal operation. If

abnormal performance is observed, additional measures may be necessary, such as reorienting or relocating the Ear

Thermometer. Over the frequency range 150kHz to 80MHz, ﬁeld strengths should be less than [V1] V/m.

14 | GB

GB | 15

Table 4 For EQUIPMENT and SYSTEMS that are not LIFE-SUPPORTING

Recommended separation distances between portable and mobile RF communications equipment

and the Ear Thermometer

The Ear Thermometer is intended for use in an electromagnetic environment in which radiated

RF distances are controlled. The customer or the user of the Ear Thermometer can help prevent

electromagnetic interference by maintaining a minimum distance between portable and mobile

RF communications equipment (transmitters) and the Ear Thermometer as recommended below

according to the maximum output power of the communications equipment.

Rated maximum

output power of

transmitter / W

Separation distance according to frequency of transmitter / m

150 kHz to 80 MHZ

d=1.2

80 MHz to 800 MHZ

d=1.2

800 MHz to 2.5 GHz

d=2.3

0.01 0.12 0.12 0.23

0.1 0.38 0.38 0.73

1 1.2 1.2 2.3

10 3.8 3.8 7.3

100 12 12 23

2 YEAR GUARANTEE

FKA Brands Ltd guarantees this product from defect in material and workmanship for a period of

2 years from the date of purchase, except as noted below. This FKA Brands Ltd product guarantee

does not cover damage caused by misuse or abuse; accident; the attachment of any unauthorised

accessory; alteration to the product; or any other conditions whatsoever that are beyond the control

of FKA Brands Ltd. This guarantee is eective only if the product is purchased and operated in the

UK / EU. A product that requires modiﬁcation or adaptation to enable it to operate in any country

other than the country for which it was designed, manufactured, approved and / or authorised,

or repair of products damaged by these modiﬁcations is not covered under this guarantee. FKA

Brands Ltd shall not be responsible for any type of incidental, consequential or special damages.

To obtain guarantee service on your product, return the product post-paid to your local service

centre along with your dated sales receipt (as proof of purchase).

Upon receipt, FKA Brands Ltd will repair or replace, as appropriate, your product and return it to

you, post-paid. Guarantee is solely through Salter Service Centre. Service of this product by anyone

other than the Salter Service Centre voids the guarantee.

This guarantee does not aect your statutory rights.

For your local Salter Service Centre, go to www.salterhousewares.co.uk/servicecentres

14 | GB

GB | 15

EXPLANATION OF SYMBOLS

The CE marking with the Registration Number of the Notiﬁed Body. This denotes the

compliance of European Medical Device Directive 93/42/EEC

Consult the instruction for use

Disposal information: Should you wish to dispose of the article, do so in accordance

with current regulations. Details are available from your local authority

Type of protection of applied part against electric shock, body ﬂoating

This product meets the basic safety and essential performance requirements

indicated in the IP22 conditioning test (protection against solid foreign objects of

12.5mm Ø and greater and against vertically falling water drops when enclosure

tilted up to 15°)

Temperature limits

European Authorized Representative

Manufacturer’s name and address

SN YYMWWWXXXXX

SN: Product Serial Number

YY: year, MM: month, WWW: working sheet, XXXXX: serial no.

The empty, completely ﬂat batteries must be disposed of through specially

designated collection boxes, recycling points or electronics retailers. You are legally

required to dispose of the batteries.

RoHS

This product fulﬁlling the requirements of the RoHS Directive 2011/65/EU.

REACH

This product fulﬁlling the requirements of the REACH Directive EC 1907/2006 and its

amendments, do not contain Substances of Very High Concern in concentration above

the limit of 0.1 %. No substance(s) is/are present in the parts of the product above

the concentration of 0.1 % weight by weight.

16 | F

F | 17

PRÉSENTATION

Ce thermomètre est destiné à eectuer des relevés intermittents de la température

corporelle humaine. Il est adapté pour les personnes de tous âges et à un usage

domestique.

Ce thermomètre fonctionne avec la technologie infrarouge et relève la température

en quelques secondes en mesurant la chaleur dégagée par l’oreille. Ce produit est

conforme aux dispositions contenues dans la directive de l’UE relative aux dispositifs

médicaux 93/42/CEE. Les avantages :

1. Mesure auriculaire

2. Aucun couvre sonde requis

3. Conception de sonde étanche

4. Résultat du relevé de sonde en une seconde

5. Mise en marche/arrêt automatique pour une économie d’énergie

6. Voyant indicateur de pile faible

7. Avertissement - mises en garde liées à l’état de la pile et à la plage de mesure.

8. Grand écran d’achage LCD

9. Fonction mémoire

INFORMATIONS IMPORTANTES AVANT UTILISATION

Lors de l’utilisation de ce produit, s’assurer de suivre toutes les indications fournies

ci-dessous. Tout non-respect de ces avis peut entraîner des blessures ou aecter la

précision de l’appareil.

1. Ne pas démonter, réparer ou altérer le thermomètre.

2. Il convient de nettoyer la lentille du thermomètre après chaque utilisation.

3. Éviter tout contact direct des doigts sur la lentille.

4. Aucune modiﬁcation de cet équipement n’est autorisée.

5. Nous conseillons d’eectuer 3 relevés de température. En cas de divergence entre

ces relevés, retenez la mesure la plus élevée.

6. Ne pas exposer le thermomètre à des températures extrêmes, à une forte humidité

ou à la lumière directe du soleil.

7. Éviter tout choc violent ou de faire tomber le thermomètre.

8. Avant d’eectuer un relevé, l’utilisateur et le thermomètre doivent rester dans une

pièce à une température ambiante constante pendant au moins 30 minutes.

9. Éviter de relever la température dans les 30 minutes qui suivent toute activité

physique, après avoir pris un bain ou être sorti(e).

Pointe de la sonde

16 | F

F | 17

10. Dans un souci de protection de l’environnement, jeter les piles usagées dans

un site une collecte de déchets appropriée conformément aux règlementations

locales ou nationales.

11. Il est déconseillé de démonter le thermomètre.

12. Veuillez utiliser le thermomètre uniquement aux ﬁns pour lesquelles il a été

conçu.

13. Tenir le thermomètre avec précaution pendant son utilisation pour éviter de le

faire tomber.

14. Laisser une minute entre chaque relevé consécutif car de légères variations

peuvent se produire si les mesures sont réalisées sur une courte période. Utiliser

plutôt une température moyenne.

15. Il n’y a pas de normes de température corporelle absolues. Conserver des relevés

ﬁables de votre température corporelle à titre de référence pour déterminer si

vous avez de la ﬁèvre.

16. Le relevé de température est fourni UNIQUEMENT à titre indicatif. Avant de prendre

toute mesure médicale, veuillez consulter votre médecin.

17. Il est recommandé de calibrer le thermomètre tous les ans.

IDENTIFICATION DU PRODUIT

Bouton de mémoire

Couvercle du

compartiment à pile

Pointe de la sonde

Bouton

d’alimentation et

de relevé

Écran LCD

18 | F

F | 19

DESCRIPTION DE L’ÉCRAN D’AFFICHAGE

CONSEILS POUR RELEVER LA TEMPÉRATURE CORPORELLE HUMAINE

N’oubliez pas que le thermomètre doit être resté dans la pièce dans laquelle le relevé

sera eectué pendant au moins 30 minutes avant son utilisation.

REMARQUE :

• Pour certaines personnes, le relevé sera diérent selon qu’il est eectué dans

l’oreille gauche ou droite. Pour relever les changements de température, toujours

prendre la température dans la même oreille.

• Le thermomètre auriculaire peut être utilisé par des enfants uniquement sous la

surveillance d’un adulte. Il est généralement possible d’eectuer des relevés dès

l’âge de 6 mois. Chez les nourrissons de moins de 6 mois, le canal auditif étant

encore très étroit, il est souvent impossible de relever la température du tympan et la

mesure achée est souvent trop faible.

• Ne pas eectuer de relevé dans une oreille comportant une atteinte inﬂammatoire

(par ex. en cas d’écoulement de l’oreille), après une blessure (par ex. tympan

endommagé) ou pendant la période de guérison après une procédure opératoire. Dans

chacun de ces cas, veuillez consulter votre médecin.

• Même si le thermomètre est nettoyé et désinfecté, il est déconseillé de l’utiliser pour

plusieurs personnes, en cas de certaines maladies infectieuses graves en raison

du risque de propagation des bactéries. En cas de doute, veuillez consulter votre

médecin.

• Ce thermomètre doit être utilisé uniquement sans couvre sonde jetable. Si vous êtes

resté(e) couché(e) sur une oreille pendant une période prolongée, la température

Température en degrés

Échelle Celsius

Échelle Fahrenheit

Relevé en coursVisage mécontent

Relevé

≥38.0°C(≥ 100.4°F)

Fièvre

Visage souriant

Relevé

<38.0°C(< 100.4°F)

Pas de ﬁèvre

Voyant indicateur de

pile faible

Symbole de mémoire et jeux d’enregistrements

18 | F

F | 19

sera légèrement augmentée.

• Attendre 60 secondes ou eectuer le relevé dans l’autre oreille.

• La présence de cérumen pouvant aecter le relevé, nettoyer l’oreille avant de prendre

la mesure si cela est nécessaire.

MODE D’EMPLOI DU THERMOMÈTRE

1. Appuyer sur le bouton d’alimentation et de relevé pendant 1 seconde pour mettre en

marche le thermomètre. Les données s’achent sur l’écran. Attendre le bip sonore

indiquant que le thermomètre est prêt à l’emploi, le relevé précédent s’ache sur

l’écran.

2. S’assurer que la pointe de la sonde et le canal auditif

sont propres. Tirer légèrement l’oreille vers le haut et

vers l’arrière pour insérer la pointe de la sonde dans

le canal auditif qui est légèrement incurvé. Ceci est

important pour s’assurer que la pointe de la sonde soit

orientée directement sur le tympan.

Enfants de moins de 1 an

L’enfant doit être couché la tête tournée d’un côté pour que l’oreille

dans laquelle le relevé sera eectué soit orientée vers le haut. Tirer

doucement sur l’oreille vers l’arrière.

3. Insérer la sonde dans le canal auditif (la sonde doit être susamment insérée

pour assurer un relevé précis de la température), puis appuyer sur le bouton

d’alimentation et de relevé pendant environ 1 seconde, relâcher le bouton, un bip

sonore bref retentit indiquant que le relevé est terminé.

4. Sortir le thermomètre de l’oreille pour lire les résultats du relevé.

5. L’achage rétroéclairé reste à l’écran pendant environ 5 secondes à chaque fois

que le bouton d’alimentation et de relevé est actionné, une fois chaque relevé

terminé, et à chaque fois que le bouton mémoire est actionné pour acher le

Enfants à partir de 1 an

Se tenir derrière et légèrement de côté par rapport à l’enfant/la

personne. Tirer doucement sur l’oreille vers le haut puis vers l’arrière

pour redresser le canal auditif.

20 | F

F | 21

résultat précédent.

6. Le thermomètre s’éteindra automatiquement après une minute d’inactivité.

Remarque :

7. Aﬁn d’assurer une mesure précise, il convient d’attendre au moins 1 minute entre

chaque relevé consécutif.

8. Nettoyer de nouveau la lentille du thermomètre après utilisation. Après le

nettoyage, attendre au moins 10 minutes entre les relevés aﬁn d’assurer la

précision des mesures.

CHANGER L’UNITÉ DE MESURE (°C/°F)

Pour basculer entre °C/°F, s’assurer que l’appareil est en marche. Appuyer simultanément

sur les boutons d’alimentation et de relevé et de mémoire pour basculer entre °C et °F.

FONCTION DE MÉMOIRE

Vous pouvez rappeler jusqu’à 10 mesures en mémoire

à partager avec votre médecin ou un professionnel de

santé compétent.

1. Appuyer sur le bouton mémoire. Le premier relevé

aché correspond à la dernière mesure mémorisée.

2. Maintenir le bouton mémoire enfoncé pour acher

l’avant-dernière mesure mémorisée.

3. Toute nouvelle mesure sera mémorisée et la mémoire la

plus ancienne sera supprimée automatiquement.

Les relevés

Si la mesure de température est inférieure à 38°C

(100.4°F), un visage souriant s’ache à côté

de la mesure.

Si la mesure de température est égale ou

supérieure à 38°C (100.4°F), un visage mécontent

s’ache.

La pagina sta caricando ...

Salter TE-150-EU Manuale del proprietario

Marca: Salter

Modello: TE-150-EU

Categoria: Termometri digitali per il corpo

Tipo: Manuale del proprietario

Questo manuale è adatto anche per

SA TE-150

Scarica il pdf

rapporto

in altre lingue

français: Salter TE-150-EU Le manuel du propriétaire
español: Salter TE-150-EU El manual del propietario
Deutsch: Salter TE-150-EU Bedienungsanleitung

Salter TE-150-EU Manuale del proprietario

Questo manuale è adatto anche per

Salter TE-150-EU Manuale del proprietario

in altre lingue

Documenti correlati

Altri documenti