SWITEL DCT7072 Manuale del proprietario
- Categoria
- Smartwatch
- Tipo
- Manuale del proprietario
Questo manuale è adatto anche per
Low−radiation cordless DECT/GAP telephone with
answering machine
Operating Instructions
DCT 707X
1
3
1 Safety Information 4. . . . . . . . . . . . . .
2 Putting the Telephone into Operation 5
3 Operating Elements 7. . . . . . . . . . . . .
4 Introductory Information 9. . . . . . . . . .
5 Menu Structure 10. . . . . . . . . . . . . . . .
6 Telephoning 11. . . . . . . . . . . . . . . . . .
7 Phonebook 13. . . . . . . . . . . . . . . . . . .
8 Call Log 13. . . . . . . . . . . . . . . . . . . . .
9 Answering Machine 14. . . . . . . . . . . . .
10 In Case of Problems 18. . . . . . . . . . . .
11 Technical Properties 19. . . . . . . . . . . .
12 Maintenance / Guarantee 20. . . . . . . .
4
1 Safety Information
Please read this operating instruction manual thoroughly.
Intended use
The telephone is suitable for telephoning within a public telephone
network system. Any other use is considered unintended use.
Unauthorised modification or reconstruction is not permitted.
Under no circumstances open the device or complete any repair
work yourself.
Installation location
Prevent excessive exposure to smoke, dust, vibration, chemicals,
moisture, heat and direct sunlight.
Do not use the handset in potentially explosive areas.
Power adapter plug
Attention: Only use the power adapter plug supplied because
other power supplies could damage the telephone. Ensure ac-
cess to the power adapter plug is not obstructed by furniture or
such.
Batteries
Attention: Never throw batteries into a fire. Only use batteries
of the same type! Pay attention to correct polarity! If the polarity
of the batteries is incorrect, there is a risk of explosion of the char-
ging station.
Power failure
The telephone cannot be used to make calls in the event of a
power failure. Always keep a cord connected telephone which op-
erates without an external power supply available in case of
emergency situations.
Medical equipment
Attention: Never use the telephone in the vicinity of medical
equipment. Effects on such equipment cannot be fully ruled out.
DECT
1
telephones can cause an unpleasant humming sound in
hearing aids.
1
DECT: Digital Enhanced Cordless Telecommunication = Stan-
dard for cordless telephones.
2
5
Disposal
In order to dispose of your device, bring it to a collection
point provided by your local public waste authorities (e.g.
recycling centre). The adjacent symbol indicates that the
device must not be disposed of in normal domestic waste!
According to laws on the disposal of electronic and elec-
trical devices, owners are obliged to dispose of old elec-
tronic and electrical devices in a separate waste con-
tainer.
Batteries must be disposed of at
the point of sale or at the appropri-
ate collection points provided by the
public waste authorities.
Packaging materials must be disposed of according to local re-
gulations.
2 Putting the Telephone into Operation
Safety information
Attention: It is essential to read the Safety Information in Chap-
ter 1 before starting up.
Checking the package contents
The package contains:
Contents
DET 397X
3971 3972
1
3973
1
3974
1
Base station with power
adapter plug
1 1 1 1
Charging station with
power adapter plug
− 1 2 3
Handset 1 2 3 4
Telephone connection ca-
ble
1 1 1 1
Batteries 2 4 6 8
Operating instructions 1 1 1 1
1
Refer to the www.switel.com web site to see if this telephone set
is already available.
6
Connecting the base station
Attention: Position the base station at least 1 m away from other
electronic devices, otherwise there is a risk of mutual distur-
bance.
Connect the base station as illustrated in the diagram. For reasons
of safety, only use the power adapter plug and telephone connec-
tion line supplied.
Mains power outlet
Telephone line socket
Attention: With regard to the base station, use the power adap-
ter plug, model No. GTSA−075030WVY3 bearing the output data:
7,5 V, 300 mA.
Connecting the charging station
1
Connect the charging station as
illustrated in the diagram. For
safety reasons, only use the
power adapter plug supplied.
Attention: With regard to the charging station, use the power
adapter plug, model No. GTSA−075020WVY3 bearing the output
data: 7,5 V, 200 mA.
Inserting the batteries
Insert the batteries in the open bat-
tery compartment. Only use batteries
of the type AAA NiMH 1,2 V.
Pay attention to correct polarity.
Close the battery compartment.
1
Only applies to telephone sets with at least two handsets
Section Package contents" on Page 5.
Mains power outlet
3
7
Charging the batteries
Before the handset is used for the first time, insert it in the base/
charging station for at least 24 hours.
When the handset is inserted in the base/charging station pro-
perly, you will hear an acoustic confirmation signal. The handset
warms up during the charging process. This is normal and does
not represent a risk. Do not charge the handset with charging units
from other manufacturers.
The current battery charge status is indicated in the display:
Full Half empty Low Empty
Setting the display language
Select a language (cf. Menu Structure"):
> Handset > Language >...
3 Operating Elements
The buttons in this operating manual are subsequently depicted
with a uniform contour. Slight deviations in the appearance of the
icons on the buttons compared to those depicted in this manual
are possible.
8
Handset
1 Display
2 Redialling /
Scroll upwards
3 Menu / OK button
4 Open calls log /
Scroll downwards
5 Phonebook /
Cancel process
6 Conference call
7 Internal call
8 R button /
Handset on/off
9 Key lock
10 Handsfree
11 Take call /
End call
12 Delete / Muting
Base station
1 Display
2 Message play / Pause
3 Back / Alert signal
4 Forward / Answer delay
5 Volume −
6 Volume +
7 Delete button /
Remote access code
8 Stop
9 Paging button
10 Answering machine On / Off
11 Charge contacts
1
2
3
4
5
6
8
10
7
11
9
12
1
2
3
4
5
6
7
8
9
10
11
1
Only applies to telephone sets with at least two handsets
Section Package contents" on Page 5.
9
Charging station
1
1 Charge contacts
Low radiation operation (ECO mode)
Default settings = ECO-MODE → OFF
The telephone can be set up so that the radiation power is re-
duced Page 11.
= ECO MODE → ON.
Reductions, with ECO mode activated, in comparison to a stan-
dard DECT cordless telephone:
Both in Call mode as well as in Standby mode, the radiation is re-
duced considerably when ECO mode is activated as compared to
standard, cordless DECT telephones.
If necessary, you can increase the range of the telephone system
by switching ECO MODE off Page 11 (ECO MODE →
OFF).
1
10
4 Introductory Information
Notation used in the operation instruction manual
Notation Description
ë Enter digits or letters
* Press the button depicted briefly
2 sec * Press the button depicted for 2 seconds
SETUP
Represents texts which appear in the
display
Represents icons which appear in the
display
Icons and texts in the handset display
Icon Description
1 Internally assigned call number of the handset
05:08:03 Time display
ext External call
int Internal call
Flashing: New calls have been registered in the calls
log.
The key lock is activated.
MUTE The microphone is switched off (muting).
On: The connection to the base station is good.
Flashing: The connection to the base station is poor.
On: The answering machine is switched on.
Flashing: New messages have been recorded.
4
11
5 Menu Structure
Open the main menu by pressing the button. Use the
y/z buttons to move to and select an option then confirm
it by pressing the ® button.
PLAY MESSAGE
NEW MSG XX
ALL MSG XX
TAM SETTINGS ANS ON/OFF
ANS MODE
MEMO REC
OGM SETTING
DAY SETTING
ANS DELAY
REMOTE CODE
PHONEBOOK ADD ENTRY
MODIFY ENTRY
DELETE ENTRY
SETUP BASE VOLUME
BASE MELODY
DEL HANDSET
PIN CODE
DIAL MODE
RECALL
DEFAULT
ECO MODE
HANDSET BEEP
INT RING VOL
EXT RING VOL
INT MELODY
EXT MELODY
AUTO ANSWER
NAME
LANGUAGE
KEYLOCK?
5
12
DATE − TIME DATE SET
CLOCK SET
ALARM SET
REGISTER SELECT BASE
REG BASE
6 Telephoning
All descriptions in this operating manual assume that the handset
is in Standby mode.
Take a call (off−hook)
End a call (on−hook)
Make an external call , ë or ë,
Redial the number y, y/z,
Dial from calls log z, y/z,
Dial from phone number
memory
´,y/z,
Internal calls
Making an internal call
I, ë e.g. 2.
There must be two or more handsets registered on the base sta-
tion in order to make internal calls.
Forwarding external calls internally / Conference calls
During a call: I, ë e.g. 2.
After the internal party has answered, transfer the call by pressing
the button.
To start a conference call, wait for the party called to answer the
internal call and then press the # button.
If the handset called does not answer, take the external call back
by pressing the I button.
13
Other functions
Function Button sequence
Switch the handset on /off 5 sec ³
Key lock on 3 sec
Key lock off ,
Receiver volume , y/z
Ringing melody volume y/z
while phone is ringing
Muting/Activating micro-
phone in handset
during the call
Locate handset (paging) on the base station
Muting function
After muting the microphone, the caller can no longer hear you.
Displaying the duration of a call
The duration of a call is displayed in hours, minutes and seconds
during the call.
Registering a handset
If your handset is not registered on the base station, icons flash in
the display.
To register the handset, press the button on the base sta-
tion for five seconds and then proceed as follows:
, y/z,
REGISTER
, ®,
y/z,
REG BASE
, ®,
BASE 1 2 3 4
.
To register a handset from a different manufacturer, refer to the
operating manual supplied with the respective handset. The four−
digit PIN for your base station is 0000.
Up to five handsets can be registered on your base station. Ho-
wever, you can only activate your handset on one base station
at a time.
6
7
14
7 Phonebook
Up to 50 phone numbers can be stored in the phonebook.
Each entry can be customised with its own individual ringtone
(10 melodies).
When the memory capacity is completely full, an existing entry must be
overwritten.
Creating phone book entries
, y/z,
PHONEBOOK
, ®, y/z,
ADD ENTRY
, ®,
NAME ?
, ë, ®,
NUMBER ?
,
ë, ®, y/z,
MELODY 1
to
MELODY 10
, ®.
Modifying phonebook entries
, y/z,
PHONEBOOK
, ®, y/z,
MODIFY ENTRY
, ®, y/z, ®, ë, ®, ë,
®, y/z,
MELODY 1
to
MELODY 10
, ®.
8 Call Log
A total of 40 phone numbers are stored in a call log.
The caller number display function is an optional service offered
by telephone network providers. If this service is not offered, the
incoming calls are not displayed. Contact your network provider
for further information.
Displaying numbers in the call log
y, y/z.
Storing an entry in the call log in the phone number memory
y, y/z, several times if necessary ®,
ADD ?
, ®,
NAME ?
ë, ®, confirm number ®,
MELODY 1
to
MELODY 10
, ®.
Deleting phone numbers from the call log
y, y/z, C,
DELETE ?
, ®.
8
15
9 Answering Machine
The answering machine can store up to 59 messages. The maximum re-
cording time is 60 minutes. When the memory capacity for new messages
is exhausted, no further messages are recorded.
Language
The voice output of the answering machine is English.
Operating using the handset
The answering machine is controlled via the buttons on the handset.
To play new messages recorded, proceed as follows:
, , y/z,
NEW MSG 01
, ®
To play all the messages recorded, proceed as follows:
, , y/z,
ALL MSG 03
, ®
To open the answering machine’s main menu, proceed as follows (pay
attention to the audio operating instructions):
, y/z,
TAM SETTINGS
, ®, y/z,
Function Display text
Button sequence
Switch answe-
ring machine
on/off
ANS ON/OFF
ON
OFF
®, y/z, ®
Select outgoing
message
(OGM)
ANS MODE
ANS AND REC
ANS ONLY
®, y/z, ®
Record memo
MEMO REC
®, follow the audio ope-
rating instructions
OGM menu
OGM SETTING
PLAY OGM
RECORD OGM
DELETE OGM
®, y/z, ®
Set weekday
DAY SETTING
SUNDAY
SATURDAY
®, y/z, ®
9
16
Answering de-
lay
ANS DELAY
TS, 2−9
®, y/z, ®
Change the PIN
code (default
setting: 000)
REMOTE CODE
®, ë, ®
Taking a call being recorded
If the answering machine has taken an incoming call, press the but-
ton to take the call personally.
Outgoing message menu
To open the OGM Setting menu, proceed as follows:
, y/z,
TAM SETTINGS
, ®, y/z,
OGM SETTING
, ®, y/z
Outgoing messages (OGM) can be recorded or deleted. After OGM 1 has
been played, the caller can leave a message.
OGM 2 is purely an answer only announcement after which no message
can be left.
Function Display text
Button sequence
Select and play
OGM
PLAY OGM
ANS AND REC
ANS ONLY
®, y/z, ®
Record OGM
RECORD OGM
ANS AND REC
ANS ONLY
®, y/z, ®,
follow the audio operating
instructions.
Delete OGM
DELETE OGM
ANS AND REC
ANS ONLY
®, y/z, ®
10
11
17
Answer delay
You can select from 2 to 9 ringing tones or the TS (Time Saver) setting for
pre−remote access free of charge.
Pre−remote access means: If new messages have been recorded on your
answering machine, your call is taken after 2 rings. If no messages have
been recorded, the call is taken after 6 rings. Place the receiver on−hook
before the 6th ring. This means that no charges ensue.
To open the Answer Delay menu, proceed as follows:
, y/z,
TAM SETTINGS
, ®, y/z,
ANS DELAY
, ®. Press y/z to select the required number of
rings. Confirm by pressing ®.
Remote access
Call your own phone number. Press the button while the outgoing
message is being played. Enter your security code (default setting: 000).
Other functions can now be started. If the answering machine is not
switched on, it takes the call after the 20th ring.
Function Button
Play all the messages 2
Play the new messages 3
Play the previous message 4
Delete messages 5
Play the next message 6
Answering machine on/off 7
OGM menu 8
Change the security code (default setting 000) 9
Play the main menu 1
Operating using the base station
The answering machine provides voice prompts. Please pay attention to
the instructions and information.
18
Switching the answering machine on/off
Switch the answering machine on/off
Setting the volume
You can set the volume of the loudspeaker.
or Set the volume required
Playing/Deleting recorded messages
Playing back messages
The recorded messages are played back in the sequence they were re-
corded. The day and time of recording are announced
before the respective message is played.
| Play new messages
Press and hold | Play all messages
s Stop playback
n Repeat playback of the message
2 x n Play the previous message
m Play the next message
Deleting one message
| Play the message to be deleted
Message is deleted while being played
Deleting all messages
All the messages which have been played can be deleted after confirming
the prompt from the operator guidance.
Delete all the messages
Selecting the answering mode
The answering machine is provided with two pre−recorded outgoing mess-
ages. After OGM 1, answering with recording, has been played the caller
can leave a message. OGM 2, answering without recording, is purely an
answer only announcement after which no message can be left. Both the
outgoing messages can be replaced by ones of your own.
When the answering machine’s memory capacity is full, OGM 2 (answering
without recording) is automatically played.
19
Answering delay
Press and hold m The selection options are announced:
Tollsaver, 2−9
Release m Release the button when the required setting is
played. The selected setting is played.
Recording memos
Memos can only be recorded via the handset.
Playing the weekday and time
s The weekday and time currently set are played.
Activating the message alert indicator
Press and hold n Message alert indicator on
Press and hold n Message alert indicator off
Playing the security code
The security code currently set is played.
10 Troubleshooting
Should problems arise with the telephone, please refer to the fol-
lowing information first. In the case of technical problems, you can
contact our hotline service, Tel. 0900 00 1675 within Switzerland
(Swisscom fees, via landline, at time of going to print: CHF
2.60/min). In the case of claims under the terms of guarantee,
please contact your sales outlet. There is a 2 year period of guar-
antee.
No dialling tone can be heard after actuating the Off−hook
button, the line is not engaged.
− Check the telephone connection at the base station and
the telephone line wall socket.
− Check the power plug connection at the base station and
the 230 V power socket.
− The line is engaged by another handset. Wait until the
connection is terminated.
Display message SEARCHING.
20
− Check the power plug connection at the base station and
the 230 V power socket.
− Reduce the range between handset and base station.
− Register handset.
Base station does not ring.
− Ringing tone is switched off −> Switch it on.
No indicators in the display.
− Handset is switched off −> Switch it on.
− Battery is empty −> Recharge it.
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
SWITEL DCT7072 Manuale del proprietario
- Categoria
- Smartwatch
- Tipo
- Manuale del proprietario
- Questo manuale è adatto anche per
in altre lingue
- English: SWITEL DCT7072 Owner's manual
Documenti correlati
-
SWITEL DCT7271 Manuale del proprietario
-
-
SWITEL DFT9971 Manuale del proprietario
-
-
-
-
-
-
-
SWITEL Vita DCT 5007x Combo Manuale utente