Pioneer PRS-D410 Manuale utente

ENGLISH

ESPAÑOL

DEUTSCH

FRANÇAIS

ITALIANO

NEDERLANDS

êìëëäàâ

BRIDGEABLE FOUR-CHANNEL POWER AMPLIFIER

AMPLIFICATEUR DE PUISSANCE PONTABLE A

QUATRE VOIES

Owner’s Manual

PRS-D400

Mode d’emploi

1
Before Using This Product  ...................... 1
Product registration ............................................ 1
In case of trouble  .............................................. 2
CAUTION.......................................................... 2
CAUTION.......................................................... 2
WARNING ........................................................ 2
Setting the Unit  .......................................... 3
Terminal Cover  ..................................................3
Cut Off Frequency Control  .............................. 3
Input Switch  ...................................................... 3
BFC (Beat Frequency Control) Switch  ............ 3
LPF (Low-Pass Filter)/HPF (High-Pass Filter)
Select Switch .................................................. 4
Input Select Switch ............................................ 4
Power Indicator  ................................................ 4
Gain Control ...................................................... 4
Connecting the Unit  .................................. 5
Connection Diagram  ........................................ 6
Connecting the Power Terminal ........................ 7
Connecting the Speaker Output Terminals  ...... 8
Using the Speaker Input  .................................... 8
Connecting the Speakers and Input Wires  ........ 9
Installation ................................................ 11
Example of installation on the floor mat 
or on the chassis  ...................................... 12
Replacing the terminal cover  .......................... 12
Specifications .......................................... 13
Thank you for purchasing this PIONEER
product. Before attempting operation, be
sure to read this manual.
Private households in the 25 member
states of the EU, in Switzerland and
Norway may return their used electronic
products free of charge to designated col-
lection facilities or to a retailer (if you pur-
chase a similar new one).
For countries not mentioned above, please
contact your local authorities for the cor-
rect method of disposal.
By doing so you will ensure that your dis-
posed product undergoes the necessary
treatment, recovery and recycling and thus
prevent potential negative effects on the
environment and human health.
Product registration
Visit us at the following site:
Register your product. We will keep the
details of your purchase on file to help you
refer to this information in the event of an
insurance claim such as loss or theft.
If you want to dispose this
product, do not mix it with
general household waste. There
is a separate collection system
for used electronic products in
accordance with legislation that
requires proper treatment,
recovery and recycling.
Contents Before Using This Product

ENGLISH

ESPAÑOL

DEUTSCH

FRANÇAIS

ITALIANO

NEDERLANDS

êìëëäàâ

2

In case of trouble

When the unit does not operate properly,

contact your dealer or the nearest autho-

rized PIONEER Service Station.

CAUTION

Never replace the fuse with one of greater

value or rating than the original fuse. Use

of an improper fuse could result in over-

heating and smoke and could cause dam-

age to the product and injury including

burns.

CAUTION

Do NOT install or use your Pioneer ampli-

fier by wiring speakers rated at 4 Ohm (or

lower) in parallel to achieve a 2 Ohm (or

lower) bridged mode (Diagram B).

Amplifier damage, smoke, and overheat-

ing could result from improper bridging.

The amplifier surface could also become

hot to the touch and minor burns could

result.

To properly install or use a bridged mode

for a two-channel amplifier and achieve a

4 Ω load, wire two 8 Ω speakers in paral-

lel with Left + and Right – (Diagram A) or

use a single 4 Ω speaker. For a four-chan-

nel amplifier, follow the speaker output

connection diagram for bridging as shown

on the back of your amplifier, and wire

two 8 Ω speakers in parallel to achieve a 4

Ω load or use a single 4 Ω speaker per

channel.

If you have any questions or concerns,

please contact your local authorized

Pioneer dealer or call Pioneer customer

service.

WARNING

• Always use the special red battery and ground

wire [RD-223], which is sold separately. Connect

the battery wire directly to the car battery positive

terminal (+) and the ground wire to the car body.

• Do not touch the amplifier with wet hands.

Otherwise you may get an electric shock. Also,

do not touch the amplifier when it is wet.

• For traffic safety and to maintain safe driving

conditions, keep the volume low enough so that

you can still hear normal traffic sound.

• Check the connections of the power supply and

speakers if the fuse of the separately sold battery

wire or the amplifier fuse blows. Detect the cause

and solve the problem, then replace the fuse with

another one of the same size and rating.

• To prevent malfunction of the amplifier and

speakers, the protective circuit will cut the power

supply to the amplifier (sound will stop) when an

abnormal condition occurs. In such a case, switch

the power to the system OFF and check the

connection of the power supply and speakers.

Detect the cause and solve the problem.

• Contact the dealer if you cannot detect the cause.

• To prevent an electric shock or short-circuit

during connection and installation, be sure to

disconnect the negative (–) terminal of the battery

beforehand.

• Confirm that no parts are behind the panel when

drilling a hole for installation of the amplifier. Be

sure to protect all cables and important equipment

such as fuel lines, brake lines and the electrical

wiring from damage.

• DO NOT allow amplifier to come into contact

with liquids due to, for example, the location

where the amplifier is installed. Electrical shock

could result. Also, amplifier and speaker damage,

smoke, and overheating could result from contact

with liquids. In addition, the amplifier surface

and the surface of any attached speakers could

become hot to the touch and minor burns could

result.

Diagram A - Proper

8

Ohm

Speaker

+

-

8

Ohm

Speaker

Pioneer

Amplifier

4 Ohm Bridged Mode

+

L+ R-

-

Diagram B - Improper

4

Ohm

Speaker

+

-

4

Ohm

Speaker

Pioneer

Amplifier

2 Ohm Bridged Mode

+

L+ R-

-

In case of trouble

When the unit does not operate properly,

contact your dealer or the nearest autho-

rized PIONEER Service Station.

CAUTION

Never replace the fuse with one of greater

value or rating than the original fuse. Use

of an improper fuse could result in over-

heating and smoke and could cause dam-

age to the product and injury including

burns.

CAUTION

Do NOT install or use your Pioneer ampli-

fier by wiring speakers rated at 4 Ohm (or

lower) in parallel to achieve a 2 Ohm (or

lower) bridged mode (Diagram B).

Amplifier damage, smoke, and overheat-

ing could result from improper bridging.

The amplifier surface could also become

hot to the touch and minor burns could

result.

To properly install or use a bridged mode

for a two-channel amplifier and achieve a

4 Ω load, wire two 8 Ω speakers in paral-

lel with Left + and Right – (Diagram A) or

use a single 4 Ω speaker. For a four-chan-

nel amplifier, follow the speaker output

connection diagram for bridging as shown

on the back of your amplifier, and wire

two 8 Ω speakers in parallel to achieve a 4

Ω load or use a single 4 Ω speaker per

channel.

If you have any questions or concerns,

please contact your local authorized

Pioneer dealer or call Pioneer customer

service.

WARNING

• Always use the special red battery and ground

wire [RD-223], which is sold separately. Connect

the battery wire directly to the car battery positive

terminal (+) and the ground wire to the car body.

• Do not touch the amplifier with wet hands.

Otherwise you may get an electric shock. Also,

do not touch the amplifier when it is wet.

• For traffic safety and to maintain safe driving

conditions, keep the volume low enough so that

you can still hear normal traffic sound.

• Check the connections of the power supply and

speakers if the fuse of the separately sold battery

wire or the amplifier fuse blows. Detect the cause

and solve the problem, then replace the fuse with

another one of the same size and rating.

• To prevent malfunction of the amplifier and

speakers, the protective circuit will cut the power

supply to the amplifier (sound will stop) when an

abnormal condition occurs. In such a case, switch

the power to the system OFF and check the

connection of the power supply and speakers.

Detect the cause and solve the problem.

• Contact the dealer if you cannot detect the cause.

• To prevent an electric shock or short-circuit

during connection and installation, be sure to

disconnect the negative (–) terminal of the battery

beforehand.

• Confirm that no parts are behind the panel when

drilling a hole for installation of the amplifier. Be

sure to protect all cables and important equipment

such as fuel lines, brake lines and the electrical

wiring from damage.

• DO NOT allow amplifier to come into contact

with liquids due to, for example, the location

where the amplifier is installed. Electrical shock

could result. Also, amplifier and speaker damage,

smoke, and overheating could result from contact

with liquids. In addition, the amplifier surface

and the surface of any attached speakers could

become hot to the touch and minor burns could

result.

Diagram A - Proper

8

Ohm

Speaker

+

-

8

Ohm

Speaker

Pioneer

Amplifier

4 Ohm Bridged Mode

+

L+ R-

-

Diagram B - Improper

4

Ohm

Speaker

+

-

4

Ohm

Speaker

Pioneer

Amplifier

2 Ohm Bridged Mode

+

L+ R-

-

3

Setting the Unit

Cut Off Frequency Control

If the LPF/HPF select switch is set to

LPF or HPF, you can select a cut off

frequency from 40 Hz to 120 Hz.

BFC (Beat Frequency Control)

Switch

BFC switch is on the bottom of the unit.

If you hear a beat while listening to an

MW/LW broadcast with your car stereo,

change the BFC switch using a small

standard tip screwdriver.

Terminal Cover

Before setting up the unit, unfasten the

screws with a 4 mm hexagonal wrench

(not supplied) and remove the terminal

cover.

Input Switch

It is possible to input from a car stereo

external output (subwoofer output) or a

car stereo speaker output. When using

an external output (subwoofer output),

slide the switch to the left. For connec-

tion instructions, see the “Connection

Diagram” section. When using a speak-

er output, slide the switch to the right. In

this case, it is necessary to use the sup-

plied speaker input wire with RCA pin

cord. For details, see the “Using the

Speaker Input” section.

ENGLISH

ESPAÑOL

DEUTSCH

FRANÇAIS

ITALIANO

NEDERLANDS

êìëëäàâ

4

Gain Control

Adjusting the gain controls A and B will help match the output of the car stereo to the

Pioneer amplifier. Normally, set the gain controls to the NORMAL position. If the output is

low, even when the volume of the car stereo is turned up, turn these controls clockwise. If

there is distortion when the volume of the car stereo is turned up, turn these controls

counter-clockwise.

• If you only use one input plug, set the gain controls for speaker outputs A and B to the same position.

• When using with an RCA equipped car stereo (standard output of 500 mV), set to the NORMAL

position. When using with an RCA equipped Pioneer car stereo with max. output of 4 V or more,

adjust level to match the car stereo output level.

Power Indicator

The power indicator lights when the

power is switched on.

Input Select Switch

For two-channel input, slide this switch

to the left. For four-channel input, slide

this switch to the right.

LPF (Low-Pass Filter)/HPF (High-Pass Filter) Select Switch

Set the LPF/HPF select switch as follows according to the type of speaker that is connected

to the speaker output connector and the car stereo system:

LPF/HPF Select Audio frequency range Speaker Remarks

Switch to be output Type

LPF (Left) * — 40 Hz to 120 Hz Subwoofer Connect a subwoofer.

OFF (Center) Full range Full range

HPF (Right) * 40 Hz to 120 Hz — Full range Use if you want to cut the

very low frequency range*

because it is not necessary

for the speakers you are

using.

* See the “Cut Off Frequency Control” section.

5

Connecting the Unit

CAUTION

• Disconnect the negative (–) terminal of the bat-

tery to avoid the risk of short-circuit and damage

to the unit.

• Secure the wiring with cable clamps or adhesive

tape. To protect the wiring, wrap adhesive tape

around it where they lie against metal parts.

• Do not route wires where they will get hot, for

example where the heater will blow over them. If

the insulation heats up, it may become damaged,

resulting in a short-circuit through the vehicle

body.

• Make sure that wires will not interfere with mov-

ing parts of the vehicle, such as the gearshift,

handbrake or seat sliding mechanism.

• Do not shorten any wires. Otherwise the protec-

tion circuit may fail to work when it should.

• Never feed power to other equipment by cutting

the insulation of the power supply wire to tap

from the wire. The current capacity of the wire

will be exceeded, causing overheating.

• Never replace the fuse with one of greater value

or rating than the original fuse. Use of an improp-

er fuse could result in overheating and smoke and

could cause damage to the product and injury

including burns.

Speaker Channel Speaker Type Power

Four-channel

Subwoofer Nominal input: Min. 75 W

Other than subwoofer Max. input: Min. 150 W

Two-channel

Subwoofer Nominal input: Min. 300 W

Other than subwoofer Max. input: Min. 600 W

Three-channel Subwoofer Nominal input: Min. 75 W

Speaker output A Other than subwoofer Max. input: Min. 150 W

Three-channel Subwoofer Nominal input: Min. 300 W

Speaker output B Other than subwoofer Max. input: Min. 600 W

CAUTION:

To prevent damage and/or injury

• Do not ground the speaker wire directly or con-

nect a negative (–) lead wire for several speakers.

• This unit is for vehicles with a 12-volt battery and

negative grounding. Before installing it in a recre-

ational vehicle, truck or bus, check the battery

voltage.

• If the car stereo is kept on for a long time while

the engine is at rest or idling, the battery may go

dead. Turn the car stereo off when the engine is at

rest or idling.

• If the system remote control wire of the amplifier

is connected to the power terminal through the

ignition switch (12 V DC), the amplifier will

always be on when the ignition is on— regardless

of whether the car stereo is on or off. Because of

this, the battery could go dead if the engine is at

rest or idling.

• Speakers to be connected to the amplifier should

conform with the standards listed below. If they

do not conform, they may catch fire, emit smoke

or become damaged. The speaker impedance

must be 2 to 8 ohms. But in case of two-channel

and other bridge connections, the speaker

impedance must be 4 to 8 ohms.

• Install and route the separately sold battery wire

as far away as possible from the speaker wires.

Install and route the separately sold battery wire,

ground wire, speaker wires and the amplifier as

far away as possible from the antenna, antenna

cable and tuner.

• Cords for this product and those for other prod-

ucts may be different colors even if they have the

same function. When connecting this product to

another product, refer to the supplied Installation

manuals of both products and connect cords that

have the same function.

ENGLISH

ESPAÑOL

DEUTSCH

FRANÇAIS

ITALIANO

NEDERLANDS

êìëëäàâ

6

Connection Diagram

• This diagram shows connections using external output (subwoofer output). Slide the input switch to the left.

• When you connect with speaker output, connections defers from the diagram. For details, see the “Using

the Speaker Input” section. In either case, you need to set the input switch. For details, see the “Setting the

Unit” section.

Grommet

RCA input

Special red battery wire [RD-223] (sold separately)

After making all other connections at the amplifier,

connect the battery wire terminal of the amplifier to

the positive (+) terminal of the battery.

Ground wire (Black) [RD-223] (sold separately)

Connect to metal body or chassis.

Amplifier with

RCA input jacks

Car stereo with

RCA output jacks

System remote control wire (sold separately)

Connect the male terminal of this wire to the system remote control

terminal of the car stereo (SYSTEM REMOTE CONTROL). The female

terminal can be connected to the auto-antenna relay control terminal. If the

car stereo does not have a system remote control terminal, connect the

male terminal to the power terminal through the ignition switch.

Fuse (30 A)

Connecting wire with

RCA pin plugs (sold

separately).

Speaker output terminal

See the “Connecting the

Speakers and Input

Wires” section for

speaker connection

instructions.

Fuse (30 A) × 2

External Output

If only one input plug is used, do

not connect anything to RCA

input jack B.

RCA input jack B

RCA output jack

RCA input jack A

7

Connecting the Unit

Connecting the Power Terminal

• Always use the special red battery and ground

wire [RD-223], which is sold separately. Connect

the battery wire directly to the car battery positive

terminal (+) and the ground wire to the car body.

1. Pass the battery wire from the

engine compartment to the interior

of the vehicle.

• After making all other connections to the

amplifier, connect the battery wire terminal

of the amplifier to the positive (+) terminal of

the battery.

2. Twist the battery wire, ground wire

and system remote control wire.

3. Attach lugs to wire ends. Lugs not

supplied.

• Use pliers, etc., to crimp lugs to wires.

4. Connect the wires to the terminal.

• Fix the wires securely with the terminal

screws.

WARNING

Failure to securely fasten the battery wire to the ter-

minal using the terminal screws could cause the ter-

minal area to overheat and could result in damage

and injury including minor burns.

Engine

compart-

ment

Interior of

the vehicle

Drill a 14 mm

hole into the

vehicle body.

Insert the O-ring rubber

grommet into the vehicle

body.

Positive terminal

GND terminal

Power terminal

Battery wire

System remote

control terminal

System remote

control wire

Ground wire

Twist

Battery wire

Ground wire

Lug

Fuse (30 A)

ENGLISH

ESPAÑOL

DEUTSCH

FRANÇAIS

ITALIANO

NEDERLANDS

êìëëäàâ

Connecting the Speaker Output

Terminals

1. Expose the end of the speaker wires

using nippers or a cutter by about

10 mm and twist.

2. Attach lugs to speaker wire ends.

Lugs not supplied.

• Use pliers, etc., to crimp lugs to wires.

3. Connect the speaker wires to the

speaker output terminals.

• Fix the speaker wires securely with the termi-

nal screws.

Using the Speaker Input

Connect the car stereo speaker output

wires to the amplifier using the supplied

speaker input wire with RCA pin cord.

• Slide the input switch to the right.

• For four-channel input, connect two speaker

input wires with RCA pin cord to RCA input

jack A and B. Be sure to slide the input select

switch to the right.

• For two-channel input, connect the speaker

input wire with RCA pin cord to RCA input

jack A. Do not connect anything to RCA

input jack B. Be sure to slide the input select

switch to the left.

7 Connections when using the speaker

input

• As a result of connecting the car stereo speaker

output wire to the amplifier, the power of the

amplifier is turned on automatically when the car

stereo is turned on. It is not necessary to connect

the system remote control wire in this case.

Note:

• Connect the system remote control wire when the

power of the amplifier is not to be turned on

when the car stereo is turned on.

10 mm

Twist

Speaker wire

Lug

Speaker

output

terminal

Terminal screw

Speaker wire

Speaker output

Speaker input

wire with RCA

pin cord

To RCA input

jack of this unit.

Car stereo

White: Black: Black: Red:

Left + Left ≠ Right ≠ Right +

8

Connecting the Speakers and Input Wires

The speaker output mode can be four-channel, three-channel (stereo + mono)

or two-channel (stereo, mono). Connect the speaker leads to suit the mode

according to the figures shown below.

Four-channel

Three-channel

≠

+

≠

+

≠

+

≠

+

9

Connecting the Unit

RCA input jack A

(Right)

Speaker out A

(Left)

RCA input jack B

Connecting wires

with RCA plugs

(sold separately)

From car stereo (RCA output)

If only one input plug is used, such as

when the car stereo has only one output

(RCA output), connect the plug to RCA

input jack A, but do not connect a plug to

RCA input jack B.

(Left)

Speaker out B

(Right)

RCA input jack A

(Right)

Speaker out A

(Left)

RCA input jack B

Connecting wires

with RCA plugs

(sold separately)

From car stereo (RCA output)

If only one input plug is used, such as

when the car stereo has only one output

(RCA output), connect the plug to RCA

input jack A, but do not connect a plug to

RCA input jack B.

Speaker out B

(Mono)

Input select switch is on the top of the unit. For two-

channel input, slide this switch to the left. For four-

channel input, slide this switch to the right.

Input select switch is on the top of the unit. For two-

channel input, slide this switch to the left. For four-

channel input, slide this switch to the right.

ENGLISH

ESPAÑOL

DEUTSCH

FRANÇAIS

ITALIANO

NEDERLANDS

êìëëäàâ

10

Two-channel (Stereo)

Two-channel (Mono)

≠

+

≠

+

≠

+

≠

+

RCA input jack A

In the case of two-channel mode

connect RCA plugs to the RCA

input jack A.

Speaker (Left)

Speaker (Right)

Connecting wire with

RCA plugs

(sold separately)

From car stereo (RCA output)

Speaker (Mono)

Connecting wire with

RCA plugs

(sold separately)

From car stereo (RCA output)

Input select switch is on

the top of the unit. Slide

this switch to the left.

RCA input jack A

In the case of two-channel mode

connect RCA plugs to the RCA

input jack A.

Input select switch is on

the top of the unit. Slide

this switch to the left.

11

Installation

CAUTION

• Do not install in:

—Places where it could injure the driver or pas-

sengers if the vehicle stops suddenly.

—Places where it may interfere with the driver,

such as on the floor in front of the driver’s

seat.

• Make sure that wires are not caught in the sliding

mechanism of the seats, resulting in a short-cir-

cuit.

• Confirm that no parts are behind the panel when

drilling a hole for installation of the amplifier.

Protect all cables and important equipment such

as fuel lines, brake lines and electrical wiring

from damage.

• Install tapping screws in such a way that the

screw tip does not touch any wire. This is impor-

tant to prevent wires from being cut by vibration

of the car, which can result in fire.

• DO NOT allow amplifier to come into contact

with liquids due to, for example, the location

where the amplifier is installed. Electrical shock

could result. Also, amplifier and speaker damage,

smoke, and overheating could result from contact

with liquids. In addition, the amplifier surface and

the surface of any attached speakers could

become hot to the touch and minor burns could

result.

• To ensure proper installation, use the supplied

parts in the manner specified. If any parts other

than the supplied ones are used, they may damage

internal parts of the amplifier, or they may

become loose causing the amplifier to shut down.

• Never replace the fuse with one of greater value

or rating than the original fuse. Use of an improp-

er fuse could result in overheating and smoke and

could cause damage to the product and injury

including burns.

CAUTION:

To prevent malfunction and/or injury

• To ensure proper heat dissipation of the amplifier,

be sure of the following during installation.

—Allow adequate space above the amplifier for

proper ventilation.

—Do not cover the amplifier with a floor mat or

carpet.

• DO NOT allow amplifier to come into contact

with liquids due to, for example, the location

where the amplifier is installed. Electrical shock

could result. Also, amplifier and speaker damage,

smoke, and overheating could result from contact

with liquids. In addition, the amplifier surface and

the surface of any attached speakers could

become hot to the touch and minor burns could

result.

• Do not install the amplifier on unstable places

such as the spare tire board.

• The best location for installation differs with the

car model and installation location. Secure the

amplifier at a sufficiently rigid location.

• Make temporary connections first and check that

the amplifier and the system operate properly.

• After installing the amplifier, confirm that the

spare tire, jack and tools can be easily removed.

ENGLISH

ESPAÑOL

DEUTSCH

FRANÇAIS

ITALIANO

NEDERLANDS

êìëëäàâ

Example of installation on the

floor mat or on the chassis

1. Place the amplifier where it is to be

installed. Insert the supplied tap-

ping screws (4 × 18 mm) into the

screw holes. Push on the screws

with a screwdriver so they make

marks where the installation holes

are to be located.

2. Drill 2.5 mm diameter holes at the

point marked, and install the ampli-

fier, either on the carpet or directly

to the chassis.

Replacing the terminal cover

1. Align the unit and terminal cover,

and insert the screw.

2. Tighten the screw with a 4 mm

hexagonal wrench (not supplied).

Tapping-screws

(4 × 18 mm)

Floor mat

or chassis

Drill a 2.5 mm diameter hole

Screw

Terminal Cover

1212

13

Specifications

Power source ........................................................................................................ 14.4 V DC (10.8 V to 15.1 V allowable)

Grounding system .......................................................................................................................................... Negative type

Current consumption .................................................................................................... 27.7 A (at continuous power, 4 Ω)

Average current drawn* ...................................................................................................... 10.4 A (4 Ω for four channels)

20.2 A (4 Ω for two channels)

20.2 A (2 Ω for four channels)

Fuse ........................................................................................................................................................................ 30 A × 2

Dimensions ...................................................................................................................... 304 (W) × 56 (H) × 202 (D) mm

Weight .................................................................................................................... 3.0 kg (Leads for wiring not included)

Maximum power output .............................................................................................. 150 W × 4 (4 Ω) / 600 W × 2 (4 Ω)

Continuous power output ............................................................ 75 W × 4 (at 14.4 V, 4 Ω, 20 Hz to 20 kHz 1.0% THD)

300 W × 2 (at 14.4 V, 4 Ω, 1 kHz 1.0% THD)

150 W × 4 (at 14.4 V, 2 Ω, 1 kHz 1.0% THD)

Load impedance ........................................................................................................................ 4 Ω (2 Ω to 8 Ω allowable)

(Bridge connection: 4 Ω to 8 Ω allowable)

Frequency response .......................................................................................................... 10 Hz to 40 kHz (+0 dB, –3 dB)

Signal-to-noise ratio .................................................................................................................... 100 dB (IEC-A network)

Distortion ........................................................................................................................................ 0.005 % (10 W, 1 kHz)

Separation ...................................................................................................................................................... 70 dB (1 kHz)

Low pass filter ............................................................................................................ Cut off frequency: 40 Hz to 120 Hz

Cut off slope: –12 dB/oct

High pass filter ............................................................................................................ Cut off frequency: 40 Hz to 120 Hz

Cut off slope: –12 dB/oct

Gain control .................................................................................................................................... RCA: 400 mV to 6.5 V

Speaker: 1.6 V to 26 V

Maximum input level / impedance ...................................................................................................... RCA: 6.5 V / 22 kΩ

Speaker: 26 V / 90 kΩ

Note:

• Specifications and the design are subject to possible modification without notice

due to improvements.

*Average current drawn

• The average current drawn is nearly the maximum current drawn by this unit

when an audio signal is input. Use this value when working out total current

drawn by multiple power amplifiers.

14

ENGLISH

ESPAÑOL

DEUTSCH

FRANÇAIS

ITALIANO

NEDERLANDS

êìëëäàâ

1
Antes de usar este producto .................... 1
Registro del producto ........................................ 1
En caso de desperfectos  .................................... 2
PRECAUCION ................................................ 2
PRECAUCION ................................................ 2
ADVERTENCIA .............................................. 2
Ajuste de esta unidad  .............................. 3
Cubierta de terminales  ...................................... 3
Control de frecuencia de corte  .......................... 3
Interruptor de entrada ........................................ 3
Interruptor BFC (Control de la frecuencia de 
batido) ........................................................ 3
Interruptor de selección LPF (Filtro de paso 
bajo)/HPF (Filtro de paso alto)  .................. 4
Interruptor de selección de entrada  .................. 4
Indicador de alimentación  ................................ 4
Control de ganancia  .......................................... 4
Conexión de la unidad .............................. 5
Diagrama de conexión  ...................................... 6
Conexión del terminal de alimentación  ............ 7
Conexión del terminal de salida de altavoz  ...... 8
Uso de la entrada de altavoz .............................. 8
Conexión de los altavoces y cables 
de entrada  .................................................. 9
Instalación ................................................ 11
Ejemplo de instalación en la alfombra del 
piso o en el chasis  .................................... 12
Recolocación de la cubierta de terminales ........12
Especificaciones .................................... 13
Muchas gracias por la adquisición de este
producto PIONEER. Antes de tratar de
operarlo, lea atentamente este manual.
Las viviendas privadas en los 25 estados
miembros de la UE, en Suiza y Noruega
pueden devolver gratuitamente sus
productos electrónicos usados en las
instalaciones de recolección previstas o
bien en las instalaciones de minoristas (si
adquieren un producto similar nuevo).
En el caso de los países que no se han
mencionado en el párrafo anterior,
póngase en contacto con sus autoridades
locales a fin de conocer el método de
eliminación correcto.
Al actuar siguiendo estas instrucciones, se
asegurará de que el producto de desecho se
somete a los procesos de tratamiento,
recuperación y reciclaje necesarios, con lo
que se previenen los efectos negativos
potenciales para el entorno y la salud
humana.
Registro del producto
Visítenos en el siguiente sitio:
Registre su producto. Conservaremos los
datos de su compra archivados para que
pueda consultar esta información en caso
de que deba efectuar un reclamo a la 
compañía de seguros por pérdida o robo.
Si desea deshacerse de este
producto, no lo mezcle con
los residuos generales de su
hogar. De conformidad con la
legislación vigente, existe un
sistema de recogida distinto
para los productos
electrónicos que requieren un
procedimiento adecuado de
tratamiento, recuperación y
reciclado.
Contenido Antes de usar este producto

ENGLISH

ESPAÑOL

DEUTSCH

FRANÇAIS

ITALIANO

NEDERLANDS

êìëëäàâ

2

En caso de desperfectos

Si esta unidad no funciona correctamente,

póngase en contacto con su distribuidor o

con el Centro de Servicio PIONEER

autorizado más cercano.

PRECAUCION

No reemplace nunca el fusible por uno con

un valor de régimen mayor que el fusible

original. El uso de un fusible inadecuado

podría causar el sobrecalantamiento o

humo, así como podría causar daños al

producto y lesiones, incluyendo

quemaduras.

PRECAUCION

NO instale o use el amplificador Pioneer

mediante la conexión de los cables de las

bocinas de 4 ohmios nominales (o menos) en

paralelo para lograr un modo en puente de 2

ohmios (o menos) (Diagrama B).

Realizar un puente incorrecto podría resultar en

un sobrecalentamiento y daño del amplificador,

así como en un desprendimiento de humo del

mismo. La superficie del amplificador podría

también ponerse caliente al tacto y resultar en

quemaduras ligeras.

Para instalar o usar adecuadamente el modo de

puente para un amplificador de dos canales y

lograr una carga de 4 Ω, conecte los cables de

dos bocinas de 8 Ω en paralelo con Izquierdo +

y Derecho – (Diagrama A), o use una sola

bocina de 4 Ω. Para un amplificador de cuatro

canales, siga el diagrama de la conexión de

salida de la bocina para crear un puente como se

muestra en la parte posterior del amplificador, y

conecte los cables de dos bocinas de 8 Ω en

paralelo para lograr una carga de 4 Ω o use una

sola bocina de 4 Ω por canal.

Si tiene preguntas o dudas, comuníquese con el

distribuidor Pioneer autorizado en su localidad

o llame al Servicio al Cliente de Pioneer.

ADVERTENCIA

• Siempre utilice el cable de batería rojo especial y

el cable de tierra [RD-223], vendidos separada-

mente. Conecte el cable de batería directamente

al terminal positivo de la batería del vehículo (+)

y el cable de tierra a la carrocería del vehículo.

• No toque en el amplificador con las manos

mojadas. Caso contrario, usted puede llevar un

choque eléctrico. Igualmente, no toque en el

amplificador cuando esté mojado.

• Para seguridad del tráfico y para mantener condi-

ciones de conducción seguras, mantenga el volu-

men suficientemente bajo de manera que aun se

pueda escuchar el sonido del tráfico normal.

• Verifique las conexiones del suministro de

energía y altavoces para ver si el fusible del cable

de batería vendido separadamente o el fusible del

amplificador se queman. Detecte la causa y solu-

cione el problema, y reemplace el fusible con un

otro del mismo tamaño y régimen.

• Para evitar mal funcionamiento del amplificador

y altavoces, el circuito de protección cortará la

alimentación al amplificador (el sonido se

detendrá) cuando se produzca una situación anor-

mal. En tal caso, apague el sistema y verifique la

conexión de la alimentación y altavoces. Detecte

la causa y resuelva el problema.

• Contacte a su distribuidor si no puede detectar la

causa.

• Para evitar choques eléctricos o cortocircuitors

durante la conexión e instalación, asegúrese de

desconectar el terminal negativo (–) de la batería

antes de proceder.

• Confirme que ninguna parte quede detrás del

panel, cuando perfore un orificio para la insta-

lación del amplificador. Asegúrese de proteger

todos los cables y equipos importantes, tales

como líneas de combustibles, líneas de frenos y el

cableado eléctrico.

• NO permita que el amplificador entre en contacto

con líquidos debido a, por ejemplo, la locali-

zación donde el amplificador esté instalado. Esto

podría causar una sacudida eléctrica. El contacto

con líquidos también podría causar daños y

sobrecalentamiento al amplificador e altavoces.

Además, la superficie del amplificador y la super-

ficie de cualquier altavoz instalado también

podrían ponerse muy calientes al tacto, pudiendo

causar pequeñas quemaduras.

Diagrama A - Correcto

A

ltavoz

de

8 ohmios

A

ltavoz

de

8 ohmios

+ -

Amplificador

Pioneer

Modo de conexión en

puente de 4 ohmios

A

ltavoz

de

4 ohmios

A

ltavoz

de

4 ohmios

Amplificador

Pioneer

Modo de conexión en

puente de 2 ohmios

+

L+ R-

-

Diagrama B - Incorrecto

+ -

+

L+ R-

-

3

Ajuste de esta unidad

Control de frecuencia de corte

Si se ajusta el interruptor de selección

LPF/HPF a LPF o HPF, se puede

seleccionar una frecuencia de corte de

40 Hz a 120 Hz.

Cubierta de terminales

Antes de montar la unidad, desapriete

los tornillos con una llave hexagonal de

4 mm (no suministrada) y quite la

cubierta de terminales.

Interruptor de entrada

Es posible introducir desde la salida exterior

de un equipo estéreo de automóvil (salida de

altavoz de graves secundario) o desde la

salida de altavoz de un equipo estéreo de

automóvil. Cuando utilice una salida

exterior (salida de altavoz de graves

secundario), deslice el interruptor hacia la

izquierda. Para las instrucciones de

instalación, consulte la sección “Diagrama

de conexión”. Cuando utilice una salida de

altavoz, deslice el interruptor hacia la

derecha. En este caso, es necesario utilizar

el hilo de entrada de altavoz suministrado

con el cable con conector RCA. Para los

detalles, consulte la sección “Uso de la

entrada de altavoz”.

Interruptor BFC (Control de la

frecuencia de batido)

El interruptor BFC se encuentra en

la parte inferior de la unidad. Si se

oye un batido durante la escucha de

una transmisión MW/LW con el

equipo estéreo de automóvil, cambie

el interruptor BFC utilizando un

destornillador pequeño.

ENGLISH

ESPAÑOL

DEUTSCH

FRANÇAIS

ITALIANO

NEDERLANDS

êìëëäàâ

4

Control de ganancia

El ajuste de los controles de ganancia A y B le ayuda a igualar la salida del equipo estéreo

para automóvil al amplificador Pioneer. Normalmente, ajuste los controles de ganancia a la

posición NORMAL. Si la potencia de salida está baja aún cuando se aumenta el volumen del

equipo estéreo del automóvil, gire esos controles a la derecha. Si se produce distorsión

cuando se aumenta el volumen del equipo estéreo de automóvil, gire los controles a la

izquierda.

• Si se usa solamente un enchufe de entrada, ajuste los controles de ganancia para las salidas de altavoz

A y B a la misma posición.

• Cuando se usa un estéreo de automóvil equipado con RCA (salida estándar de 500 mV), ajuste a la

posición NORMAL. Cuando use con un estéreo de automóvil Pioneer equipado con RCA con una

salida máxima de 4 V o más, ajuste el nivel para adecuarse al nivel de salida del estéreo del

automóvil.

Indicador de alimentación

El indicador de alimentación se ilumina

cuando la unidad se encuentra activada.

Interruptor de selección de

entrada

Para la entrada de dos canales, deslice

este interruptor hacia la izquierda. Para

la entrada de cuatro canales, deslice este

interruptor hacia la derecha.

Interruptor de selección LPF (Filtro de paso bajo)/HPF (Filtro de paso

alto)

Ajuste el interruptor de selección LPF/HPF de la manera siguiente, de acuerdo al tipo de

altavoz que se encuentra conectado al conector de salida de altavoz y al sistema estéreo de

automóvil:

Interruptor de Gama de frecuencia Tipo de Observaciones

selección LPF/HPF de audio a ser generada altavoz

LPF (izquierda) * — 40 Hz a 120 Hz Altavoz de graves Conecte a un altavoz

secundario de graves secundario.

OFF (central) Gama completa Gama completa

HPF (derecha) * 40 Hz a 120 Hz — Gama completa Utilice si desea cortar la

gama de frecuencia*

muy baja debido a que

no es necesaria para el

altavoz que está usando.

* Consulte a “Control de frecuencia de corte”.

5

Conexión de la unidad

PRECAUCION

• Quite el terminal negativo (–) de la batería para

evitar riesgo de cortocircuitos y daño a la unidad.

• Asegure el alambrado con abrazaderas de cable o

cinta adhesiva. Para proteger el alambrado,

envuelva cinta adhesiva alrededor de ellos en

donde contacta con partes metálicas.

• No tienda cables por donde puedan calentarse,

por ejemplo donde el calentador sople sobre ellos.

Si la aislación se calienta, podría resultar dañada,

resultando en cortocircuito a través de la carro-

cería del vehículo.

• Asegúrese que los alambres no interfieran con

partes móviles del vehículo como la palanca de

cambios, el freno de mano o el mecanismo de

deslizamiento de los asientos.

• No corte ningún cable. De otra manera, el circuito

de protección podría no funcionar cuando

debiera.

• Nunca alimente otro equipo cortando la aislación

del cable de alimentación y conectándolo al

cable. La capacidad de corriente del cable será

excedida, causando sobrecalentamiento.

• No reemplace nunca el fusible por uno con un

valor de régimen mayor que el fusible original. El

uso de un fusible inadecuado podría causar el

sobrecalantamiento o humo, así como podría

causar daños al producto y lesiones, incluyendo

quemaduras.

Canal de altavoces

Tipo de altavoz Alimentación

Cuatro canales

Altavoz de graves secundario Entrada nominal: 75 W mín.

Diferente a un altavoz de graves secundario Entrada máxima: 150 W mín.

Dos canales

Altavoz de graves secundario Entrada nominal: 300 W mín.

Diferente a un altavoz de graves secundario Entrada máxima: 600 W mín.

Salida de altavoz A Altavoz de graves secundario Entrada nominal: 75 W mín.

de tres canales Diferente a un altavoz de graves secundario Entrada máxima: 150 W mín.

Salida de altavoz B Altavoz de graves secundario Entrada nominal: 300 W mín.

de tres canales Diferente a un altavoz de graves secundario Entrada máxima: 600 W mín.

PRECAUCION:

Para evitar daños y/o lesiones

• No conecte a tierra (masa) el cable del altavoz

directamente ni conecte un cable negativo (–) a

varios altavoces.

• Esta unidad es para vehículos con una batería de

12 voltios y terminal negativo a tierra. Antes de

instalar en un vehículo de recreación, camión u

ómnibus, verifique el voltaje de la batería.

• Si el sistema estereofónico del coche está funcio-

nando por un largo período de tiempo mientras el

motor permanece inactivo o en marcha al ralentí,

la batería puede agotarse. Apague el estéreo de

automóvil cuando el motor se encuentre funcio-

nando en marcha al ralenté o permanece in acti-

vo.

• Si el cable del control remoto de sistema del

amplificador se conecta al terminal de ali-

mentación a través del interruptor de encendido

(12 V de CC), el amplificador estará siempre acti-

vado cuando el encendido está activado, sin con-

siderar de si el estéreo de automóvil se encuentra

activado o desactivado. Debido a esto, la batería

puede agotarse si deja el motor funcionando en

marcha al ralentí o permanece inactivo.

• Los altavoces a ser conectados al amplificador

deben estar conforme con las normas listadas

debajo. Si no cumplen con las normas, pueden

combustionar, emitir humos o dañarse. El

impedimiento altavoz debe estar de 2 a 8 ohms,

pero en caso de que dos canales y otros puentes

contecten, el impedimiento de altavoz debe ester

de 4 a 8 ohms.

• Instale y coloque el cable de batería vendido sep-

aradamente lo más alejado posible de los cables

de los altavoces. Instale y coloque el cable de

batería y cable de tierra vendidos separadamente,

los cables de los altavoces, y el amplificador lo

más alejados posible de la antena, cable de antena

y sintonizador.

• Los cables para esta unidad y aquéllas para las

unidades pueden ser de colores diferentes aun si

tienen la misma función. Cuando se conecta esta

unidad a otra, refiérase a los manuales de insta-

lación de ambas unidades y conecte los cables

que tienen la misma función.

La pagina sta caricando ...

Pioneer PRS-D410 Manuale utente

Questo manuale è adatto anche per

Pioneer PRS-D410 Manuale utente

in altre lingue

Documenti correlati

Altri documenti