Pioneer PRS-D400 Manuale utente

Categoria
Amplificatori audio per auto
Tipo
Manuale utente

Questo manuale è adatto anche per

ENGLISH
ESPAÑOL
DEUTSCH
FRANÇAIS
ITALIANO
NEDERLANDS
êìëëäàâ
BRIDGEABLE FOUR-CHANNEL POWER AMPLIFIER
AMPLIFICATEUR DE PUISSANCE PONTABLE A
QUATRE VOIES
Owner’s Manual
PRS-D400
Mode d’emploi
1
Before Using This Product ...................... 1
Product registration ............................................ 1
In case of trouble .............................................. 2
CAUTION.......................................................... 2
CAUTION.......................................................... 2
WARNING ........................................................ 2
Setting the Unit .......................................... 3
Terminal Cover ..................................................3
Cut Off Frequency Control .............................. 3
Input Switch ...................................................... 3
BFC (Beat Frequency Control) Switch ............ 3
LPF (Low-Pass Filter)/HPF (High-Pass Filter)
Select Switch .................................................. 4
Input Select Switch ............................................ 4
Power Indicator ................................................ 4
Gain Control ...................................................... 4
Connecting the Unit .................................. 5
Connection Diagram ........................................ 6
Connecting the Power Terminal ........................ 7
Connecting the Speaker Output Terminals ...... 8
Using the Speaker Input .................................... 8
Connecting the Speakers and Input Wires ........ 9
Installation ................................................ 11
Example of installation on the floor mat
or on the chassis ...................................... 12
Replacing the terminal cover .......................... 12
Specifications .......................................... 13
Thank you for purchasing this PIONEER
product. Before attempting operation, be
sure to read this manual.
Private households in the 25 member
states of the EU, in Switzerland and
Norway may return their used electronic
products free of charge to designated col-
lection facilities or to a retailer (if you pur-
chase a similar new one).
For countries not mentioned above, please
contact your local authorities for the cor-
rect method of disposal.
By doing so you will ensure that your dis-
posed product undergoes the necessary
treatment, recovery and recycling and thus
prevent potential negative effects on the
environment and human health.
Product registration
Visit us at the following site:
Register your product. We will keep the
details of your purchase on file to help you
refer to this information in the event of an
insurance claim such as loss or theft.
If you want to dispose this
product, do not mix it with
general household waste. There
is a separate collection system
for used electronic products in
accordance with legislation that
requires proper treatment,
recovery and recycling.
Contents Before Using This Product
ENGLISH
ESPAÑOL
DEUTSCH
FRANÇAIS
ITALIANO
NEDERLANDS
êìëëäàâ
2
In case of trouble
When the unit does not operate properly,
contact your dealer or the nearest autho-
rized PIONEER Service Station.
CAUTION
Never replace the fuse with one of greater
value or rating than the original fuse. Use
of an improper fuse could result in over-
heating and smoke and could cause dam-
age to the product and injury including
burns.
CAUTION
Do NOT install or use your Pioneer ampli-
fier by wiring speakers rated at 4 Ohm (or
lower) in parallel to achieve a 2 Ohm (or
lower) bridged mode (Diagram B).
Amplifier damage, smoke, and overheat-
ing could result from improper bridging.
The amplifier surface could also become
hot to the touch and minor burns could
result.
To properly install or use a bridged mode
for a two-channel amplifier and achieve a
4 load, wire two 8 speakers in paral-
lel with Left + and Right – (Diagram A) or
use a single 4 speaker. For a four-chan-
nel amplifier, follow the speaker output
connection diagram for bridging as shown
on the back of your amplifier, and wire
two 8 speakers in parallel to achieve a 4
load or use a single 4 speaker per
channel.
If you have any questions or concerns,
please contact your local authorized
Pioneer dealer or call Pioneer customer
service.
WARNING
Always use the special red battery and ground
wire [RD-223], which is sold separately. Connect
the battery wire directly to the car battery positive
terminal (+) and the ground wire to the car body.
Do not touch the amplifier with wet hands.
Otherwise you may get an electric shock. Also,
do not touch the amplifier when it is wet.
For traffic safety and to maintain safe driving
conditions, keep the volume low enough so that
you can still hear normal traffic sound.
Check the connections of the power supply and
speakers if the fuse of the separately sold battery
wire or the amplifier fuse blows. Detect the cause
and solve the problem, then replace the fuse with
another one of the same size and rating.
To prevent malfunction of the amplifier and
speakers, the protective circuit will cut the power
supply to the amplifier (sound will stop) when an
abnormal condition occurs. In such a case, switch
the power to the system OFF and check the
connection of the power supply and speakers.
Detect the cause and solve the problem.
Contact the dealer if you cannot detect the cause.
To prevent an electric shock or short-circuit
during connection and installation, be sure to
disconnect the negative (–) terminal of the battery
beforehand.
Confirm that no parts are behind the panel when
drilling a hole for installation of the amplifier. Be
sure to protect all cables and important equipment
such as fuel lines, brake lines and the electrical
wiring from damage.
DO NOT allow amplifier to come into contact
with liquids due to, for example, the location
where the amplifier is installed. Electrical shock
could result. Also, amplifier and speaker damage,
smoke, and overheating could result from contact
with liquids. In addition, the amplifier surface
and the surface of any attached speakers could
become hot to the touch and minor burns could
result.
Diagram A - Proper
8
Ohm
Speaker
+
-
8
Ohm
Speaker
Pioneer
Amplifier
4 Ohm Bridged Mode
+
L+ R-
-
Diagram B - Improper
4
Ohm
Speaker
+
-
4
Ohm
Speaker
Pioneer
Amplifier
2 Ohm Bridged Mode
+
L+ R-
-
In case of trouble
When the unit does not operate properly,
contact your dealer or the nearest autho-
rized PIONEER Service Station.
CAUTION
Never replace the fuse with one of greater
value or rating than the original fuse. Use
of an improper fuse could result in over-
heating and smoke and could cause dam-
age to the product and injury including
burns.
CAUTION
Do NOT install or use your Pioneer ampli-
fier by wiring speakers rated at 4 Ohm (or
lower) in parallel to achieve a 2 Ohm (or
lower) bridged mode (Diagram B).
Amplifier damage, smoke, and overheat-
ing could result from improper bridging.
The amplifier surface could also become
hot to the touch and minor burns could
result.
To properly install or use a bridged mode
for a two-channel amplifier and achieve a
4 load, wire two 8 speakers in paral-
lel with Left + and Right – (Diagram A) or
use a single 4 speaker. For a four-chan-
nel amplifier, follow the speaker output
connection diagram for bridging as shown
on the back of your amplifier, and wire
two 8 speakers in parallel to achieve a 4
load or use a single 4 speaker per
channel.
If you have any questions or concerns,
please contact your local authorized
Pioneer dealer or call Pioneer customer
service.
WARNING
Always use the special red battery and ground
wire [RD-223], which is sold separately. Connect
the battery wire directly to the car battery positive
terminal (+) and the ground wire to the car body.
Do not touch the amplifier with wet hands.
Otherwise you may get an electric shock. Also,
do not touch the amplifier when it is wet.
For traffic safety and to maintain safe driving
conditions, keep the volume low enough so that
you can still hear normal traffic sound.
Check the connections of the power supply and
speakers if the fuse of the separately sold battery
wire or the amplifier fuse blows. Detect the cause
and solve the problem, then replace the fuse with
another one of the same size and rating.
To prevent malfunction of the amplifier and
speakers, the protective circuit will cut the power
supply to the amplifier (sound will stop) when an
abnormal condition occurs. In such a case, switch
the power to the system OFF and check the
connection of the power supply and speakers.
Detect the cause and solve the problem.
Contact the dealer if you cannot detect the cause.
To prevent an electric shock or short-circuit
during connection and installation, be sure to
disconnect the negative (–) terminal of the battery
beforehand.
Confirm that no parts are behind the panel when
drilling a hole for installation of the amplifier. Be
sure to protect all cables and important equipment
such as fuel lines, brake lines and the electrical
wiring from damage.
DO NOT allow amplifier to come into contact
with liquids due to, for example, the location
where the amplifier is installed. Electrical shock
could result. Also, amplifier and speaker damage,
smoke, and overheating could result from contact
with liquids. In addition, the amplifier surface
and the surface of any attached speakers could
become hot to the touch and minor burns could
result.
Diagram A - Proper
8
Ohm
Speaker
+
-
8
Ohm
Speaker
Pioneer
Amplifier
4 Ohm Bridged Mode
+
L+ R-
-
Diagram B - Improper
4
Ohm
Speaker
+
-
4
Ohm
Speaker
Pioneer
Amplifier
2 Ohm Bridged Mode
+
L+ R-
-
3
Setting the Unit
Cut Off Frequency Control
If the LPF/HPF select switch is set to
LPF or HPF, you can select a cut off
frequency from 40 Hz to 120 Hz.
BFC (Beat Frequency Control)
Switch
BFC switch is on the bottom of the unit.
If you hear a beat while listening to an
MW/LW broadcast with your car stereo,
change the BFC switch using a small
standard tip screwdriver.
Terminal Cover
Before setting up the unit, unfasten the
screws with a 4 mm hexagonal wrench
(not supplied) and remove the terminal
cover.
Input Switch
It is possible to input from a car stereo
external output (subwoofer output) or a
car stereo speaker output. When using
an external output (subwoofer output),
slide the switch to the left. For connec-
tion instructions, see the “Connection
Diagram” section. When using a speak-
er output, slide the switch to the right. In
this case, it is necessary to use the sup-
plied speaker input wire with RCA pin
cord. For details, see the “Using the
Speaker Input” section.
ENGLISH
ESPAÑOL
DEUTSCH
FRANÇAIS
ITALIANO
NEDERLANDS
êìëëäàâ
4
Gain Control
Adjusting the gain controls A and B will help match the output of the car stereo to the
Pioneer amplifier. Normally, set the gain controls to the NORMAL position. If the output is
low, even when the volume of the car stereo is turned up, turn these controls clockwise. If
there is distortion when the volume of the car stereo is turned up, turn these controls
counter-clockwise.
If you only use one input plug, set the gain controls for speaker outputs A and B to the same position.
When using with an RCA equipped car stereo (standard output of 500 mV), set to the NORMAL
position. When using with an RCA equipped Pioneer car stereo with max. output of 4 V or more,
adjust level to match the car stereo output level.
Power Indicator
The power indicator lights when the
power is switched on.
Input Select Switch
For two-channel input, slide this switch
to the left. For four-channel input, slide
this switch to the right.
LPF (Low-Pass Filter)/HPF (High-Pass Filter) Select Switch
Set the LPF/HPF select switch as follows according to the type of speaker that is connected
to the speaker output connector and the car stereo system:
LPF/HPF Select Audio frequency range Speaker Remarks
Switch to be output Type
LPF (Left) * — 40 Hz to 120 Hz Subwoofer Connect a subwoofer.
OFF (Center) Full range Full range
HPF (Right) * 40 Hz to 120 Hz — Full range Use if you want to cut the
very low frequency range*
because it is not necessary
for the speakers you are
using.
* See the “Cut Off Frequency Control” section.
5
Connecting the Unit
CAUTION
Disconnect the negative (–) terminal of the bat-
tery to avoid the risk of short-circuit and damage
to the unit.
Secure the wiring with cable clamps or adhesive
tape. To protect the wiring, wrap adhesive tape
around it where they lie against metal parts.
Do not route wires where they will get hot, for
example where the heater will blow over them. If
the insulation heats up, it may become damaged,
resulting in a short-circuit through the vehicle
body.
Make sure that wires will not interfere with mov-
ing parts of the vehicle, such as the gearshift,
handbrake or seat sliding mechanism.
Do not shorten any wires. Otherwise the protec-
tion circuit may fail to work when it should.
Never feed power to other equipment by cutting
the insulation of the power supply wire to tap
from the wire. The current capacity of the wire
will be exceeded, causing overheating.
Never replace the fuse with one of greater value
or rating than the original fuse. Use of an improp-
er fuse could result in overheating and smoke and
could cause damage to the product and injury
including burns.
Speaker Channel Speaker Type Power
Four-channel
Subwoofer Nominal input: Min. 75 W
Other than subwoofer Max. input: Min. 150 W
Two-channel
Subwoofer Nominal input: Min. 300 W
Other than subwoofer Max. input: Min. 600 W
Three-channel Subwoofer Nominal input: Min. 75 W
Speaker output A Other than subwoofer Max. input: Min. 150 W
Three-channel Subwoofer Nominal input: Min. 300 W
Speaker output B Other than subwoofer Max. input: Min. 600 W
CAUTION:
To prevent damage and/or injury
Do not ground the speaker wire directly or con-
nect a negative (–) lead wire for several speakers.
This unit is for vehicles with a 12-volt battery and
negative grounding. Before installing it in a recre-
ational vehicle, truck or bus, check the battery
voltage.
If the car stereo is kept on for a long time while
the engine is at rest or idling, the battery may go
dead. Turn the car stereo off when the engine is at
rest or idling.
If the system remote control wire of the amplifier
is connected to the power terminal through the
ignition switch (12 V DC), the amplifier will
always be on when the ignition is on— regardless
of whether the car stereo is on or off. Because of
this, the battery could go dead if the engine is at
rest or idling.
Speakers to be connected to the amplifier should
conform with the standards listed below. If they
do not conform, they may catch fire, emit smoke
or become damaged. The speaker impedance
must be 2 to 8 ohms. But in case of two-channel
and other bridge connections, the speaker
impedance must be 4 to 8 ohms.
Install and route the separately sold battery wire
as far away as possible from the speaker wires.
Install and route the separately sold battery wire,
ground wire, speaker wires and the amplifier as
far away as possible from the antenna, antenna
cable and tuner.
Cords for this product and those for other prod-
ucts may be different colors even if they have the
same function. When connecting this product to
another product, refer to the supplied Installation
manuals of both products and connect cords that
have the same function.
ENGLISH
ESPAÑOL
DEUTSCH
FRANÇAIS
ITALIANO
NEDERLANDS
êìëëäàâ
6
Connection Diagram
This diagram shows connections using external output (subwoofer output). Slide the input switch to the left.
When you connect with speaker output, connections defers from the diagram. For details, see the “Using
the Speaker Input” section. In either case, you need to set the input switch. For details, see the “Setting the
Unit” section.
Grommet
RCA input
Special red battery wire [RD-223] (sold separately)
After making all other connections at the amplifier,
connect the battery wire terminal of the amplifier to
the positive (+) terminal of the battery.
Ground wire (Black) [RD-223] (sold separately)
Connect to metal body or chassis.
Amplifier with
RCA input jacks
Car stereo with
RCA output jacks
System remote control wire (sold separately)
Connect the male terminal of this wire to the system remote control
terminal of the car stereo (SYSTEM REMOTE CONTROL). The female
terminal can be connected to the auto-antenna relay control terminal. If the
car stereo does not have a system remote control terminal, connect the
male terminal to the power terminal through the ignition switch.
Fuse (30 A)
Fuse (30 A)
Connecting wire with
RCA pin plugs (sold
separately).
Speaker output terminal
See the “Connecting the
Speakers and Input
Wires” section for
speaker connection
instructions.
Fuse (30 A) × 2
External Output
If only one input plug is used, do
not connect anything to RCA
input jack B.
RCA input jack B
RCA output jack
RCA input jack A
7
Connecting the Unit
Connecting the Power Terminal
Always use the special red battery and ground
wire [RD-223], which is sold separately. Connect
the battery wire directly to the car battery positive
terminal (+) and the ground wire to the car body.
1. Pass the battery wire from the
engine compartment to the interior
of the vehicle.
After making all other connections to the
amplifier, connect the battery wire terminal
of the amplifier to the positive (+) terminal of
the battery.
2. Twist the battery wire, ground wire
and system remote control wire.
3. Attach lugs to wire ends. Lugs not
supplied.
Use pliers, etc., to crimp lugs to wires.
4. Connect the wires to the terminal.
Fix the wires securely with the terminal
screws.
WARNING
Failure to securely fasten the battery wire to the ter-
minal using the terminal screws could cause the ter-
minal area to overheat and could result in damage
and injury including minor burns.
Engine
compart-
ment
Interior of
the vehicle
Drill a 14 mm
hole into the
vehicle body.
Insert the O-ring rubber
grommet into the vehicle
body.
Positive terminal
GND terminal
Power terminal
Battery wire
System remote
control terminal
System remote
control wire
Ground wire
Twist
Battery wire
Ground wire
Lug
Lug
Fuse (30 A)
Fuse (30 A)
ENGLISH
ESPAÑOL
DEUTSCH
FRANÇAIS
ITALIANO
NEDERLANDS
êìëëäàâ
Connecting the Speaker Output
Terminals
1. Expose the end of the speaker wires
using nippers or a cutter by about
10 mm and twist.
2. Attach lugs to speaker wire ends.
Lugs not supplied.
Use pliers, etc., to crimp lugs to wires.
3. Connect the speaker wires to the
speaker output terminals.
Fix the speaker wires securely with the termi-
nal screws.
Using the Speaker Input
Connect the car stereo speaker output
wires to the amplifier using the supplied
speaker input wire with RCA pin cord.
Slide the input switch to the right.
For four-channel input, connect two speaker
input wires with RCA pin cord to RCA input
jack A and B. Be sure to slide the input select
switch to the right.
For two-channel input, connect the speaker
input wire with RCA pin cord to RCA input
jack A. Do not connect anything to RCA
input jack B. Be sure to slide the input select
switch to the left.
7 Connections when using the speaker
input
As a result of connecting the car stereo speaker
output wire to the amplifier, the power of the
amplifier is turned on automatically when the car
stereo is turned on. It is not necessary to connect
the system remote control wire in this case.
Note:
Connect the system remote control wire when the
power of the amplifier is not to be turned on
when the car stereo is turned on.
10 mm
Twist
Speaker wire
Lug
Speaker
output
terminal
Terminal screw
Speaker wire
Speaker output
Speaker input
wire with RCA
pin cord
To RCA input
jack of this unit.
Car stereo
White: Black: Black: Red:
Left + Left Right Right +
8
Connecting the Speakers and Input Wires
The speaker output mode can be four-channel, three-channel (stereo + mono)
or two-channel (stereo, mono). Connect the speaker leads to suit the mode
according to the figures shown below.
Four-channel
Three-channel
+
+
+
+
+
+
+
9
Connecting the Unit
RCA input jack A
(Right)
Speaker out A
(Left)
RCA input jack B
Connecting wires
with RCA plugs
(sold separately)
From car stereo (RCA output)
If only one input plug is used, such as
when the car stereo has only one output
(RCA output), connect the plug to RCA
input jack A, but do not connect a plug to
RCA input jack B.
(Left)
Speaker out B
(Right)
RCA input jack A
(Right)
Speaker out A
(Left)
RCA input jack B
Connecting wires
with RCA plugs
(sold separately)
From car stereo (RCA output)
If only one input plug is used, such as
when the car stereo has only one output
(RCA output), connect the plug to RCA
input jack A, but do not connect a plug to
RCA input jack B.
Speaker out B
(Mono)
Input select switch is on the top of the unit. For two-
channel input, slide this switch to the left. For four-
channel input, slide this switch to the right.
Input select switch is on the top of the unit. For two-
channel input, slide this switch to the left. For four-
channel input, slide this switch to the right.
ENGLISH
ESPAÑOL
DEUTSCH
FRANÇAIS
ITALIANO
NEDERLANDS
êìëëäàâ
10
Two-channel (Stereo)
Two-channel (Mono)
+
+
+
+
RCA input jack A
In the case of two-channel mode
connect RCA plugs to the RCA
input jack A.
Speaker (Left)
Speaker (Right)
Connecting wire with
RCA plugs
(sold separately)
From car stereo (RCA output)
Speaker (Mono)
Speaker (Mono)
Connecting wire with
RCA plugs
(sold separately)
From car stereo (RCA output)
Input select switch is on
the top of the unit. Slide
this switch to the left.
RCA input jack A
In the case of two-channel mode
connect RCA plugs to the RCA
input jack A.
Input select switch is on
the top of the unit. Slide
this switch to the left.
11
Installation
CAUTION
Do not install in:
Places where it could injure the driver or pas-
sengers if the vehicle stops suddenly.
Places where it may interfere with the driver,
such as on the floor in front of the driver’s
seat.
Make sure that wires are not caught in the sliding
mechanism of the seats, resulting in a short-cir-
cuit.
Confirm that no parts are behind the panel when
drilling a hole for installation of the amplifier.
Protect all cables and important equipment such
as fuel lines, brake lines and electrical wiring
from damage.
Install tapping screws in such a way that the
screw tip does not touch any wire. This is impor-
tant to prevent wires from being cut by vibration
of the car, which can result in fire.
DO NOT allow amplifier to come into contact
with liquids due to, for example, the location
where the amplifier is installed. Electrical shock
could result. Also, amplifier and speaker damage,
smoke, and overheating could result from contact
with liquids. In addition, the amplifier surface and
the surface of any attached speakers could
become hot to the touch and minor burns could
result.
To ensure proper installation, use the supplied
parts in the manner specified. If any parts other
than the supplied ones are used, they may damage
internal parts of the amplifier, or they may
become loose causing the amplifier to shut down.
Never replace the fuse with one of greater value
or rating than the original fuse. Use of an improp-
er fuse could result in overheating and smoke and
could cause damage to the product and injury
including burns.
CAUTION:
To prevent malfunction and/or injury
To ensure proper heat dissipation of the amplifier,
be sure of the following during installation.
Allow adequate space above the amplifier for
proper ventilation.
Do not cover the amplifier with a floor mat or
carpet.
DO NOT allow amplifier to come into contact
with liquids due to, for example, the location
where the amplifier is installed. Electrical shock
could result. Also, amplifier and speaker damage,
smoke, and overheating could result from contact
with liquids. In addition, the amplifier surface and
the surface of any attached speakers could
become hot to the touch and minor burns could
result.
Do not install the amplifier on unstable places
such as the spare tire board.
The best location for installation differs with the
car model and installation location. Secure the
amplifier at a sufficiently rigid location.
Make temporary connections first and check that
the amplifier and the system operate properly.
After installing the amplifier, confirm that the
spare tire, jack and tools can be easily removed.
ENGLISH
ESPAÑOL
DEUTSCH
FRANÇAIS
ITALIANO
NEDERLANDS
êìëëäàâ
Example of installation on the
floor mat or on the chassis
1. Place the amplifier where it is to be
installed. Insert the supplied tap-
ping screws (4 × 18 mm) into the
screw holes. Push on the screws
with a screwdriver so they make
marks where the installation holes
are to be located.
2. Drill 2.5 mm diameter holes at the
point marked, and install the ampli-
fier, either on the carpet or directly
to the chassis.
Replacing the terminal cover
1. Align the unit and terminal cover,
and insert the screw.
2. Tighten the screw with a 4 mm
hexagonal wrench (not supplied).
Tapping-screws
(4 × 18 mm)
Floor mat
or chassis
Drill a 2.5 mm diameter hole
Screw
Terminal Cover
1212
13
Specifications
Power source ........................................................................................................ 14.4 V DC (10.8 V to 15.1 V allowable)
Grounding system .......................................................................................................................................... Negative type
Current consumption .................................................................................................... 27.7 A (at continuous power, 4 )
Average current drawn* ...................................................................................................... 10.4 A (4 for four channels)
20.2 A (4 for two channels)
20.2 A (2 for four channels)
Fuse ........................................................................................................................................................................ 30 A × 2
Dimensions ...................................................................................................................... 304 (W) × 56 (H) × 202 (D) mm
Weight .................................................................................................................... 3.0 kg (Leads for wiring not included)
Maximum power output .............................................................................................. 150 W × 4 (4 ) / 600 W × 2 (4 )
Continuous power output ............................................................ 75 W × 4 (at 14.4 V, 4 , 20 Hz to 20 kHz 1.0% THD)
300 W × 2 (at 14.4 V, 4 , 1 kHz 1.0% THD)
150 W × 4 (at 14.4 V, 2 , 1 kHz 1.0% THD)
Load impedance ........................................................................................................................ 4 (2 to 8 allowable)
(Bridge connection: 4 to 8 allowable)
Frequency response .......................................................................................................... 10 Hz to 40 kHz (+0 dB, –3 dB)
Signal-to-noise ratio .................................................................................................................... 100 dB (IEC-A network)
Distortion ........................................................................................................................................ 0.005 % (10 W, 1 kHz)
Separation ...................................................................................................................................................... 70 dB (1 kHz)
Low pass filter ............................................................................................................ Cut off frequency: 40 Hz to 120 Hz
Cut off slope: –12 dB/oct
High pass filter ............................................................................................................ Cut off frequency: 40 Hz to 120 Hz
Cut off slope: –12 dB/oct
Gain control .................................................................................................................................... RCA: 400 mV to 6.5 V
Speaker: 1.6 V to 26 V
Maximum input level / impedance ...................................................................................................... RCA: 6.5 V / 22 k
Speaker: 26 V / 90 k
Note:
Specifications and the design are subject to possible modification without notice
due to improvements.
*Average current drawn
The average current drawn is nearly the maximum current drawn by this unit
when an audio signal is input. Use this value when working out total current
drawn by multiple power amplifiers.
14
ENGLISH
ESPAÑOL
DEUTSCH
FRANÇAIS
ITALIANO
NEDERLANDS
êìëëäàâ
1
Antes de usar este producto .................... 1
Registro del producto ........................................ 1
En caso de desperfectos .................................... 2
PRECAUCION ................................................ 2
PRECAUCION ................................................ 2
ADVERTENCIA .............................................. 2
Ajuste de esta unidad .............................. 3
Cubierta de terminales ...................................... 3
Control de frecuencia de corte .......................... 3
Interruptor de entrada ........................................ 3
Interruptor BFC (Control de la frecuencia de
batido) ........................................................ 3
Interruptor de selección LPF (Filtro de paso
bajo)/HPF (Filtro de paso alto) .................. 4
Interruptor de selección de entrada .................. 4
Indicador de alimentación ................................ 4
Control de ganancia .......................................... 4
Conexión de la unidad .............................. 5
Diagrama de conexión ...................................... 6
Conexión del terminal de alimentación ............ 7
Conexión del terminal de salida de altavoz ...... 8
Uso de la entrada de altavoz .............................. 8
Conexión de los altavoces y cables
de entrada .................................................. 9
Instalación ................................................ 11
Ejemplo de instalación en la alfombra del
piso o en el chasis .................................... 12
Recolocación de la cubierta de terminales ........12
Especificaciones .................................... 13
Muchas gracias por la adquisición de este
producto PIONEER. Antes de tratar de
operarlo, lea atentamente este manual.
Las viviendas privadas en los 25 estados
miembros de la UE, en Suiza y Noruega
pueden devolver gratuitamente sus
productos electrónicos usados en las
instalaciones de recolección previstas o
bien en las instalaciones de minoristas (si
adquieren un producto similar nuevo).
En el caso de los países que no se han
mencionado en el párrafo anterior,
póngase en contacto con sus autoridades
locales a fin de conocer el método de
eliminación correcto.
Al actuar siguiendo estas instrucciones, se
asegurará de que el producto de desecho se
somete a los procesos de tratamiento,
recuperación y reciclaje necesarios, con lo
que se previenen los efectos negativos
potenciales para el entorno y la salud
humana.
Registro del producto
Visítenos en el siguiente sitio:
Registre su producto. Conservaremos los
datos de su compra archivados para que
pueda consultar esta información en caso
de que deba efectuar un reclamo a la
compañía de seguros por pérdida o robo.
Si desea deshacerse de este
producto, no lo mezcle con
los residuos generales de su
hogar. De conformidad con la
legislación vigente, existe un
sistema de recogida distinto
para los productos
electrónicos que requieren un
procedimiento adecuado de
tratamiento, recuperación y
reciclado.
Contenido Antes de usar este producto
ENGLISH
ESPAÑOL
DEUTSCH
FRANÇAIS
ITALIANO
NEDERLANDS
êìëëäàâ
2
En caso de desperfectos
Si esta unidad no funciona correctamente,
póngase en contacto con su distribuidor o
con el Centro de Servicio PIONEER
autorizado más cercano.
PRECAUCION
No reemplace nunca el fusible por uno con
un valor de régimen mayor que el fusible
original. El uso de un fusible inadecuado
podría causar el sobrecalantamiento o
humo, así como podría causar daños al
producto y lesiones, incluyendo
quemaduras.
PRECAUCION
NO instale o use el amplificador Pioneer
mediante la conexión de los cables de las
bocinas de 4 ohmios nominales (o menos) en
paralelo para lograr un modo en puente de 2
ohmios (o menos) (Diagrama B).
Realizar un puente incorrecto podría resultar en
un sobrecalentamiento y daño del amplificador,
así como en un desprendimiento de humo del
mismo. La superficie del amplificador podría
también ponerse caliente al tacto y resultar en
quemaduras ligeras.
Para instalar o usar adecuadamente el modo de
puente para un amplificador de dos canales y
lograr una carga de 4 , conecte los cables de
dos bocinas de 8 en paralelo con Izquierdo +
y Derecho – (Diagrama A), o use una sola
bocina de 4 . Para un amplificador de cuatro
canales, siga el diagrama de la conexión de
salida de la bocina para crear un puente como se
muestra en la parte posterior del amplificador, y
conecte los cables de dos bocinas de 8 en
paralelo para lograr una carga de 4 o use una
sola bocina de 4 por canal.
Si tiene preguntas o dudas, comuníquese con el
distribuidor Pioneer autorizado en su localidad
o llame al Servicio al Cliente de Pioneer.
ADVERTENCIA
Siempre utilice el cable de batería rojo especial y
el cable de tierra [RD-223], vendidos separada-
mente. Conecte el cable de batería directamente
al terminal positivo de la batería del vehículo (+)
y el cable de tierra a la carrocería del vehículo.
No toque en el amplificador con las manos
mojadas. Caso contrario, usted puede llevar un
choque eléctrico. Igualmente, no toque en el
amplificador cuando esté mojado.
Para seguridad del tráfico y para mantener condi-
ciones de conducción seguras, mantenga el volu-
men suficientemente bajo de manera que aun se
pueda escuchar el sonido del tráfico normal.
Verifique las conexiones del suministro de
energía y altavoces para ver si el fusible del cable
de batería vendido separadamente o el fusible del
amplificador se queman. Detecte la causa y solu-
cione el problema, y reemplace el fusible con un
otro del mismo tamaño y régimen.
Para evitar mal funcionamiento del amplificador
y altavoces, el circuito de protección cortará la
alimentación al amplificador (el sonido se
detendrá) cuando se produzca una situación anor-
mal. En tal caso, apague el sistema y verifique la
conexión de la alimentación y altavoces. Detecte
la causa y resuelva el problema.
Contacte a su distribuidor si no puede detectar la
causa.
Para evitar choques eléctricos o cortocircuitors
durante la conexión e instalación, asegúrese de
desconectar el terminal negativo (–) de la batería
antes de proceder.
Confirme que ninguna parte quede detrás del
panel, cuando perfore un orificio para la insta-
lación del amplificador. Asegúrese de proteger
todos los cables y equipos importantes, tales
como líneas de combustibles, líneas de frenos y el
cableado eléctrico.
NO permita que el amplificador entre en contacto
con líquidos debido a, por ejemplo, la locali-
zación donde el amplificador esté instalado. Esto
podría causar una sacudida eléctrica. El contacto
con líquidos también podría causar daños y
sobrecalentamiento al amplificador e altavoces.
Además, la superficie del amplificador y la super-
ficie de cualquier altavoz instalado también
podrían ponerse muy calientes al tacto, pudiendo
causar pequeñas quemaduras.
Diagrama A - Correcto
A
ltavoz
de
8 ohmios
A
ltavoz
de
8 ohmios
+ -
Amplificador
Pioneer
Modo de conexión en
puente de 4 ohmios
A
ltavoz
de
4 ohmios
A
ltavoz
de
4 ohmios
Amplificador
Pioneer
Modo de conexión en
puente de 2 ohmios
+
L+ R-
-
Diagrama B - Incorrecto
+ -
+
L+ R-
-
3
Ajuste de esta unidad
Control de frecuencia de corte
Si se ajusta el interruptor de selección
LPF/HPF a LPF o HPF, se puede
seleccionar una frecuencia de corte de
40 Hz a 120 Hz.
Cubierta de terminales
Antes de montar la unidad, desapriete
los tornillos con una llave hexagonal de
4 mm (no suministrada) y quite la
cubierta de terminales.
Interruptor de entrada
Es posible introducir desde la salida exterior
de un equipo estéreo de automóvil (salida de
altavoz de graves secundario) o desde la
salida de altavoz de un equipo estéreo de
automóvil. Cuando utilice una salida
exterior (salida de altavoz de graves
secundario), deslice el interruptor hacia la
izquierda. Para las instrucciones de
instalación, consulte la sección “Diagrama
de conexión”. Cuando utilice una salida de
altavoz, deslice el interruptor hacia la
derecha. En este caso, es necesario utilizar
el hilo de entrada de altavoz suministrado
con el cable con conector RCA. Para los
detalles, consulte la sección “Uso de la
entrada de altavoz”.
Interruptor BFC (Control de la
frecuencia de batido)
El interruptor BFC se encuentra en
la parte inferior de la unidad. Si se
oye un batido durante la escucha de
una transmisión MW/LW con el
equipo estéreo de automóvil, cambie
el interruptor BFC utilizando un
destornillador pequeño.
ENGLISH
ESPAÑOL
DEUTSCH
FRANÇAIS
ITALIANO
NEDERLANDS
êìëëäàâ
4
Control de ganancia
El ajuste de los controles de ganancia A y B le ayuda a igualar la salida del equipo estéreo
para automóvil al amplificador Pioneer. Normalmente, ajuste los controles de ganancia a la
posición NORMAL. Si la potencia de salida está baja aún cuando se aumenta el volumen del
equipo estéreo del automóvil, gire esos controles a la derecha. Si se produce distorsión
cuando se aumenta el volumen del equipo estéreo de automóvil, gire los controles a la
izquierda.
Si se usa solamente un enchufe de entrada, ajuste los controles de ganancia para las salidas de altavoz
A y B a la misma posición.
Cuando se usa un estéreo de automóvil equipado con RCA (salida estándar de 500 mV), ajuste a la
posición NORMAL. Cuando use con un estéreo de automóvil Pioneer equipado con RCA con una
salida máxima de 4 V o más, ajuste el nivel para adecuarse al nivel de salida del estéreo del
automóvil.
Indicador de alimentación
El indicador de alimentación se ilumina
cuando la unidad se encuentra activada.
Interruptor de selección de
entrada
Para la entrada de dos canales, deslice
este interruptor hacia la izquierda. Para
la entrada de cuatro canales, deslice este
interruptor hacia la derecha.
Interruptor de selección LPF (Filtro de paso bajo)/HPF (Filtro de paso
alto)
Ajuste el interruptor de selección LPF/HPF de la manera siguiente, de acuerdo al tipo de
altavoz que se encuentra conectado al conector de salida de altavoz y al sistema estéreo de
automóvil:
Interruptor de Gama de frecuencia Tipo de Observaciones
selección LPF/HPF de audio a ser generada altavoz
LPF (izquierda) * — 40 Hz a 120 Hz Altavoz de graves Conecte a un altavoz
secundario de graves secundario.
OFF (central) Gama completa Gama completa
HPF (derecha) * 40 Hz a 120 Hz — Gama completa Utilice si desea cortar la
gama de frecuencia*
muy baja debido a que
no es necesaria para el
altavoz que está usando.
* Consulte a “Control de frecuencia de corte”.
5
Conexión de la unidad
PRECAUCION
Quite el terminal negativo (–) de la batería para
evitar riesgo de cortocircuitos y daño a la unidad.
Asegure el alambrado con abrazaderas de cable o
cinta adhesiva. Para proteger el alambrado,
envuelva cinta adhesiva alrededor de ellos en
donde contacta con partes metálicas.
No tienda cables por donde puedan calentarse,
por ejemplo donde el calentador sople sobre ellos.
Si la aislación se calienta, podría resultar dañada,
resultando en cortocircuito a través de la carro-
cería del vehículo.
Asegúrese que los alambres no interfieran con
partes móviles del vehículo como la palanca de
cambios, el freno de mano o el mecanismo de
deslizamiento de los asientos.
No corte ningún cable. De otra manera, el circuito
de protección podría no funcionar cuando
debiera.
Nunca alimente otro equipo cortando la aislación
del cable de alimentación y conectándolo al
cable. La capacidad de corriente del cable será
excedida, causando sobrecalentamiento.
No reemplace nunca el fusible por uno con un
valor de régimen mayor que el fusible original. El
uso de un fusible inadecuado podría causar el
sobrecalantamiento o humo, así como podría
causar daños al producto y lesiones, incluyendo
quemaduras.
Canal de altavoces
Tipo de altavoz Alimentación
Cuatro canales
Altavoz de graves secundario Entrada nominal: 75 W mín.
Diferente a un altavoz de graves secundario Entrada máxima: 150 W mín.
Dos canales
Altavoz de graves secundario Entrada nominal: 300 W mín.
Diferente a un altavoz de graves secundario Entrada máxima: 600 W mín.
Salida de altavoz A Altavoz de graves secundario Entrada nominal: 75 W mín.
de tres canales Diferente a un altavoz de graves secundario Entrada máxima: 150 W mín.
Salida de altavoz B Altavoz de graves secundario Entrada nominal: 300 W mín.
de tres canales Diferente a un altavoz de graves secundario Entrada máxima: 600 W mín.
PRECAUCION:
Para evitar daños y/o lesiones
No conecte a tierra (masa) el cable del altavoz
directamente ni conecte un cable negativo (–) a
varios altavoces.
Esta unidad es para vehículos con una batería de
12 voltios y terminal negativo a tierra. Antes de
instalar en un vehículo de recreación, camión u
ómnibus, verifique el voltaje de la batería.
Si el sistema estereofónico del coche está funcio-
nando por un largo período de tiempo mientras el
motor permanece inactivo o en marcha al ralentí,
la batería puede agotarse. Apague el estéreo de
automóvil cuando el motor se encuentre funcio-
nando en marcha al ralenté o permanece in acti-
vo.
Si el cable del control remoto de sistema del
amplificador se conecta al terminal de ali-
mentación a través del interruptor de encendido
(12 V de CC), el amplificador estará siempre acti-
vado cuando el encendido está activado, sin con-
siderar de si el estéreo de automóvil se encuentra
activado o desactivado. Debido a esto, la batería
puede agotarse si deja el motor funcionando en
marcha al ralentí o permanece inactivo.
Los altavoces a ser conectados al amplificador
deben estar conforme con las normas listadas
debajo. Si no cumplen con las normas, pueden
combustionar, emitir humos o dañarse. El
impedimiento altavoz debe estar de 2 a 8 ohms,
pero en caso de que dos canales y otros puentes
contecten, el impedimiento de altavoz debe ester
de 4 a 8 ohms.
Instale y coloque el cable de batería vendido sep-
aradamente lo más alejado posible de los cables
de los altavoces. Instale y coloque el cable de
batería y cable de tierra vendidos separadamente,
los cables de los altavoces, y el amplificador lo
más alejados posible de la antena, cable de antena
y sintonizador.
Los cables para esta unidad y aquéllas para las
unidades pueden ser de colores diferentes aun si
tienen la misma función. Cuando se conecta esta
unidad a otra, refiérase a los manuales de insta-
lación de ambas unidades y conecte los cables
que tienen la misma función.
1 / 1

Pioneer PRS-D400 Manuale utente

Categoria
Amplificatori audio per auto
Tipo
Manuale utente
Questo manuale è adatto anche per