Makita MS-3202E Manuale utente

Marca: Makita

Modello: MS-3202E

Categoria: Tagliaerba

Tipo: Manuale utente

Questo manuale è adatto anche per

Brush Cutter

Decespugliatore

Desbrozadora

MS-3202

MS-3202 E

String Trimmer

Tagliabordi

Cortabordes

MS-3212

Important:

Read this instruction manual carefully before putting the Brush Cutter/String Trimmer into operation and strictly observe the safety

regulations!

Preserve instruction manual carefully!

Importante:

Prima di mettere in funzione il decespugliatore/tagliabordi, leggere attentamente il presente manuale; rispettare rigorosamente le norme

di sicurezza!

Conservare il manuale delle istruzioni per l’uso!

Importante:

Leer cuidadosamente este manual de instrucciones antes de poner en marcha la máquina y observar estrictamente las normas de

seguridad.

Conservar este manual de instrucciones con cuidado.

MS-3202

MS-3212

English / Italiano / Spanish

MS-3202 E

ORIGINAL INSTRUCTION MANUAL

MANUALE DI ISTRUZIONI ORIGINALE

MANUAL DE INSTRUCCIONES ORIGINAL

Thank you very much for purchasing the DOLMAR Brush Cutter/String trimmer.

We are pleased to recommend to you the DOLMAR Brush Cutter/String trimmer

which is the result of a long development programme and many years of

knowledge and experience.

Please read this booklet which refers in detail to the various points that will

demonstrate its outstanding performance. This will assist you to obtain the

best possible result from your DOLMAR Brush Cutter/String trimmer.

Table of Contents Page

Symbols...................................................................... 1

Safety instructions ..................................................... 2

Technical data ............................................................ 6

Designation of parts ................................................... 7

Mounting of handle ..................................................... 8

Mounting of protector ................................................. 9

Mounting of cutter blade or nylon cutting head ......... 10

Before start of operation .......................................... 11

Correct handling of machine ..................................... 13

Points in operation and how to stop ......................... 13

Resharpening the cutting tool ................................... 14

Servicing instructions ............................................... 16

Storage ..................................................................... 18

Take Particular care and Attention

Read instruction Manual

Forbidden

No Smoking

No open flame

Protective gloves must be worn

Keep the area of operation clear of all

persons and pets

Wear eye and ear protection

(for String trimmer only)

Wear protective helmet, eye and ear

protection (for Brush Cutter only)

Engine-Manual start

Top permissible tool speed

Emergency stop

ON/START

OFF/STOP

Flying object hazard

Keep distance

Kickback

Do not use metal blades

(for String trimmer only)

Fuel and oil mixture

First Aid

You will note the following symbols when reading the instructions manual.

SYMBOLS

Wear sturdy boots with nonslip soles.

Steel toed safety boots are recommended.

English

SAFETY INSTRUCTIONS

General Instructions

– To ensure correct operation, user has to read this instruction manual to make

himself familiar with the handling of the Brush Cutter/String trimmer. Users

insufficiently informed will risk danger to themselves as well as others due

to improper handling.

–It is recommended only to lend the Brush Cutter/String trimmer to people who

have proven to be experienced with Brush Cutter/String trimmers.

Always hand over the instruction manual.

– First users should ask the dealer for basic instructions to familiarize oneself

with the handling of an engine powered cutter.

– Children and young persons aged under 18 years must not be allowed to

operate the Brush Cutter/String trimmer. Persons over the age of 16 years

may however use the device for the purpose of being trained only whilst

under supervision of a qualified trainer.

– Use Brush Cutter/String trimmers with the utmost care and attention.

– Operate the Brush Cutter/String trimmer only if you are in good physical

condition. Perform all work calmly and carefully. The user has to accept

liability for others.

– Never use the Brush Cutter/String trimmer after consumption of alcohol or

drugs, or if feeling tired or ill.

– National regulation can restrict the use of the machine.

Intended use of the machine

– The Brush Cutter/String trimmer is only intended for cutter grass, weeds,

Bushes, undergrowth it should not be used for any other purpose such as

Edging or hedge cutting as this may cause injury.

Personal protective equipment

– The clothing worn should be functional and appropriate, i.e. it should be

tight-fitting but not cause hindrance. Do not wear either jewelry or clothing

which could become entangled with bushes or shrubs.

– In order to avoid either head-, eye-, hand-or foot injuries as well as to

protect your hearing the following protective equipment and protective

clothing must be used during operation of the Brush Cutter/String trimmer.

– Always wear a helmet where there is a risk of falling objects. The protec-

tive helmet (1) is to be checked at regular intervals for damage and is to be

replaced at the latest after 5 years. Use only approved protective helmets.

– The visor (2) of the helmet (or alternatively goggles) protects the face from

flying debris and stones. During operation of the Brush Cutter/String trimmer

always wear goggles, or a visor to prevent eye injuries.

– Wear adequate noise protection equipment to avoid hearing impairment (ear

muffs (3), ear plugs etc.).

– The work overalls (4) protect against flying stones and debris.

We strongly recommend that the user wears work overalls.

– Special gloves (5) made of thick leather are part of the prescribed equipment

and must always be worn during operation of the Brush Cutter/String

trimmer.

– When using the Brush Cutter/String trimmer, always wear sturdy shoes (6)

with a non-slip sole. This protects against injuries and ensures a good

footing.

Starting up the brush cutter

– Please make sure that there are no children or other people within a working

range of 15 meters (49ft), also pay attention to any animals in the working

vicinity.

– Before use always check that the Brush Cutter/String trimmer is safe for

operation:

Check the security of the cutting tool, the control lever for easy action and

check for proper functioning of the control lever lock.

– Rotation of the cutting tool during idling speed is not allowed. Check with

your dealer for adjustment if in doubt. Check for clean and dry handles and

test the function of the start/stop switch.

Diagrammatic figure

15 meters

Start the Brush Cutter/String trimmer only in accordance with the instructions.

Do not use any other methods for starting the engine!

– Use the Brush Cutter/String trimmer and the tools only for such applications

as specified.

– Only start the Brush Cutter/String trimmer engine, after the entire assembly is

done. Operation of the device is only permitted after all the appropriate

accessories are attached!

– Before starting make sure that the cutting tool has no contact with hard

objects such as branches, stones etc. as the cutting tool will revolve when

starting.

– The engine is to be switched off immediately in case of any engine problems.

– Should the cutting tool hit stones or other hard objects, immediately switch

off the engine and inspect the cutting tool.

– Inspect the cutting tool at short regular intervals for damage (detection of

hairline cracks by means of tapping-noise test).

– Operate the Brush Cutter/String trimmer only with the shoulder strap

attached which is to be suitably adjusted before putting the Brush Cutter/

String trimmer into operation. It is essential to adjust the shoulder strap

according to the user’s size to prevent fatigue occurring during use. Never

hold the cutter with one hand during use.

– During operation always hold the Brush Cutter/String trimmer with both hands.

Always ensure a safe footing.

– Operate the Brush Cutter/String trimmer in such a manner as to avoid

inhalation of the exhaust gases. Never run the engine in enclosed rooms

(risk of gas poisoning). Carbon monoxide is an odorless gas.

– Switch off the engine when resting and when leaving the Brush Cutter/

String trimmer unattended, and place it in a safe location to prevent danger to

others or damage to the machine.

– Never put the hot Brush Cutter/String trimmer onto dry grass or onto any

combustible materials.

– The cutting tool has to be equipped with it’s appropriate guard.

Never run the cutter without this guard!

– All protective installations and guards supplied with the machine must be

used during operation.

– Never operate the engine with faulty exhaust muffler.

– Shut off the engine during transport.

– When transporting the equipment, always attach the cover to the cutting blade.

– Ensure safe position of the Brush Cutter/String trimmer during car transpor-

tation to avoid fuel leakage.

– When transporting the Brush Cutter/String trimmer, ensure that the fuel tank

is completely empty.

–

When unloading the Brush Cutter/String trimmer from the truck, never drop

the Engine to the ground or this may severely damage the fuel tank.

– Except in case of emergency, never drop or cast the Brush Cutter/String

trimmer to the ground or this may severely damage the Brush Cutter/String

trimmer.

– Remember to lift the entire equipment from the ground when moving the

equipment. Dragging the fuel tank is highly dangerous and will cause

damage and leakage of fuel, possibly causing fire.

– If the equipment gets heavy impact or fall, check the condition before

continuing work. Check the fuel system for fuel leakage and the controls and

safety devices for malfunction. If there is any damage or doubt, ask our

authorized service center for the inspection and repair.

Refuelling

– Shut off the engine during refuelling, keep away from open flames and do

not smoke.

– Avoid skin contact with mineral oil products. Do not inhale fuel vapor.

Always wear protective gloves during refuelling. Change and clean

protective clothing at regular intervals.

– Take care not to spill either fuel or oil in order to prevent soil contamination

(environmental protection). Clean the Brush Cutter/String trimmer immediately

after fuel has been spilt.

– Avoid any fuel contact with your clothing. Change your clothing instantly if

fuel has been spilt on it (to prevent clothing catching fire).

– Inspect the fuel cap at regular intervals making sure that it can be securely

fastened and does not leak.

– Carefully tighten the fuel tank cap. Change location to start the engine (at

least 3 meters away from the place of refuelling).

– Never refuel in closed rooms. Fuel vapors accumulate at ground lever (risk

of explosions).

– Only transport and store fuel in approved containers. Make sure the fuel

stored is not accessible to children.

• Resting

• Transport

• Refuelling

• Maintenance

• Tool Replacement

Method of operation

– Only use the Brush cutter/String trimmer in good light and visibility. During the

winter season beware of slippery or wet areas, ice and snow (risk of

slipping). Always ensure a safe footing.

– Never cut above waist height.

– Never stand on a ladder and run the Brush cutter/String trimmer.

– Never climb up into trees to perform cutting operation with the Brush cutter/

String trimmer.

– Never work on unstable surfaces.

– Remove sand, stones, nails etc. found within the working range.

Foreign particles may damage the cutting tool and can cause dangerous

kick-backs.

– Before commencing cutting, the cutting tool must have reached full working

speed.

– If grass or branches get caught between the cutting tool and guard, always

stop the engine before cleaning. Otherwise unintentional blade rotation may

cause serious injury.

– Take a rest to prevent loss of control caused by fatigue. We recommend to

take a 10 to 20-minute rest every hour.

Kickback (blade thrust)

– When operating the brush cutter, uncontrolled kickback may occur.

– This is particularly the case when attempting to cut within a blade segment

between 12 and 2 o’clock.

– Never apply the brush cutter within a segment between 12 and 2 o’clock.

– Never apply this segment of the brush cutter blade to solids, such as

bushes and trees, etc., having a diameter in excess of 3 cm or the brush

cutter will be deflected at great force with the risk of injuries.

Kickback prevention

To avoid kickbacks, observe the fol lowing:

– Operation within a blade segment between 12 and 2 o’clock presents

positive hazards, especially when using metal cutting tools.

– Cutting operations within a blade segment between 11 and 12 o’clock, and

between 2 and 5 o’clock, must only be performed by trained and experi-

enced operators, and then only at their own risk.

Easy cutting with almost no kickback is possible within a blade segment

between 8 and 11 o’clock.

Cutting Tools

Employ only the correct cutting tool for the job in hand.

MS-3202/3202 E with cutter blade (Star Blade (4 teeth), Eddy Blade (8 teeth)),

MS-3212 with Nylon cutting head.

Never use other blades including metal multi-piece pivoting chains and flail

blades. Otherwise serious injury may result.

For cutting thick materials, such as weed, high grass, bushes, shrubs,

underwood, thicket etc. (max. 2 cm dia. thickness). Perform this cutting work

by swinging the brush cutter evenly in half-circles from right to left (similar to

using a scythe).

Maintenance instructions

– Have your equipment serviced by our authorized service center, always

using only genuine replacement parts. Incorrect repair and poor maintenance

can shorten the life of the equipment and increase the risk of accidents.

– The condition of the cutter, in particular of the cutting tool of the protective

devices and also of the shoulder strap must be checked before commencing

work. Particular attention is to be paid to the cutting blades which must be

correctly sharpened.

– Turn off the engine and remove spark plug connector when replacing or

sharpening cutting tools, and also when cleaning the cutter or cutting tool.

Caution:

Kickback

Diagrammatic

flgure

Diagrammatic

flgure

Never straighten or weld damaged cutting tools.

– Operate the Brush cutter/String trimmer with as little noise and contamination

as possible. In particular check the correct setting of the carburetor.

– Clean the Brush cutter/String trimmer at regular intervals and check that all

screws and nuts are well tightened.

– Never service or store the Brush cutter/String trimmer in the vicinity of naked

flames.

– Always store the Brush cutter/String trimmer in locked rooms and with an

emptied fuel tank.

– When cleaning, servicing and storing the equipment, always attach the

cover to the cutting blade.

Observe the relevant accident prevention instructions issued by the relevant trade associations and by the insurance companies.

Do not perform any modifications on the Brush cutter/String trimmer as this will endanger your safety.

The performance of maintenance or repair work by the user is limited to those activities as described in the instruction manual. All other

work is to be done by an Authorized Service Agent. Use only genuine spare parts and accessories released and supplied by DOLMAR.

Use of non-approved accessories and tools means increased risk of accidents.

DOLMAR will not accept any liability for accidents or damage caused by the use of non-approved cutting tools and fixing devices of cutting

tools, or accessories.

First Aid

In case of accident make sure that a first-aid box is available in the vicinity of

the cutting operations. Immediately replace any item taken from the first aid

box.

When asking for help, please give the following information:

– Place of accident

– What happened

– Number of injured persons

– Kind of injuries

– Your name

Vibration

– People with poor circulation who are exposed to excessive vibration may

experience injury to blood vessels or the nervous system. Vibration may

cause the following symptoms to occur in the fingers, hands or wrists:

"Falling asleep" (numbness), tingling, pain, stabbing sensation, alteration of

skin color or of the skin. If any of these symptoms occur, see a physician!

– To reduce the risk of "white finger disease", keep your hands warm during

operation and well maintain the equipment and accessories.

For European countries only

EC Declaration of Conformity

The undersigned, Tamiro Kishima and Rainer Bergfeld, as authorized by Dolmar GmbH, declare that the DOLMAR machine(s):

Designation of Machine: Brush Cutter/String Trimmer

Model No./ Type: MS-3202, MS-3202 E, MS-3212

Specifications: see “TECHNICAL DATA” table

are of series production and

Conforms to the following European Directives:

2000/14/EC, 2006/42/EC

And are manufactured in accordance with the following standards or standardized documents:

EN ISO 11806-1

The technical documentation is on file at:

Dolmar GmbH,

Jenfelder Straße 38, Abteilung FZ, D-22045 Hamburg

The conformity assessment procedure required by Directive 2000/14/EC was in Accordance with annex V.

Measured Sound Power Level: 109.9 dB

Guaranteed Sound Power Level: 113 dB

3. 11. 2009

Tamiro Kishima Rainer Bergfeld

Managing Director Managing Director

TECHNICAL DATA MS-3202, MS-3202 E, MS-3212

MS-3202 MS-3202 E MS-3212

Model

U handle E handle Loop handle

Dimensions : length x width x height (without cutting blade) mm

1800x620x430 1800x600x435 1800x350x250

Mass (without plastic guard and cutting blade) kg

5.5 5.5 5.4

Volume (fuel tank) L

0.8

Engine displacement cm

30.5

Maximum engine performance kw

0.95 at 7000 min

-1

Engine speed at recommended max. spindle speed min

-1

10000

Maximum spindle speed (corresponding) min

-1

6800

Maximum fuel consumption kg/h

Maximum specific fuel consumption g/kwh

Idling speed min

-1

2800

Clutch engagement speed min

-1

3700

Carburetor type

WALBRO WYJ

Ignition system type

Solid state ignition

Spark plug type

NGK BMR7A

Electrode gap mm

0.6 - 0.7

hv eq

m/s

4.6 5.2 5.9

Right handle

(Rear grip)

Uncertainty K m/s

0.5 0.6 0.4

hv eq

m/s

4.4 5.5 8.3

Vibration per

ISO 22867

Left handle

(Front grip)

Uncertainty K m/s

0.8 0.4 0.9

PA eq

dBA

90.6 90.6 95.2

Sound pressure level average to

ISO 22868

Uncertainty K dBA

2.4 2.4 2.3

WA eq

dBA

100.9 100.9 106.9

Sound power level average to

ISO 22868

Uncertainty K dBA

1.4 1.4 2.8

Fuel

Mixed gas

(gasoline: DOLMAR Genuine Two-stroke Engine Oil = 50:1)

Gear ratio

13/19

DESIGNATION OF PARTS

MS-3202

U Handle Type

MS-3212

Loop Handle Type

GB DESIGNATION OF PARTS

1 Fuel Tank

2 Rewind Starter

3 Air Cleaner

4 I-O Switch (on/off)

5 Spark Plug

6 Exhaust Muffler

7 Clutch Case

8 Rear Grip

9 Hanger

10 Handle

11 Control Lever

12 Control Cable

13 Shaft

14 Protector (Cutting tool guard)

15 Gear Case

16 Handle Holder

17 Cutter Blade

18 Nylon Cutting Head

19 Fuel Filler Cap

20 Starter Knob

21 Primmer Pump

22 Choke Lever

23 Exhaust Pipe

(17)

(12)

(13)

(14)

(4)

(11)

(9)

(10)

(16)

(15)

MS-3202 E

E Handle Type

(17)

(12)

(13)

(14)

(4)

(11)

(9)

(10)

(16)

(15)

(18)

(12)

(13)

(14)

(4)

(11)

(10)

(15)

(8)

(9)

CAUTION: Before doing any work on the brush cutter, always switch off the

motor and pull the spark plug connector off the spark plug.

Always wear protective gloves.

CAUTION: Start the brush cutter only after having assembled it completely.

–Loosen the two bolts (1) and insert the main pipe (2) into the case clutch (3).

–Insert it up to the arrow-mark position. (Refer to the sketch on the right.)

If it is difficult to insert, turn the spline (4) a little and re-insert.

–Match the hole (5) of the main pipe (2) with the bolt hole (6) of the case clutch,

and tighten the attached bolts (7).

–Tighten the two bolts (1) uniformly on the right and left by Allen wrench

supplied.

ASSEMBLY OF ENGINE AND SHAFT

Connection of the switch cord

Connect the switch cords to the two cords from the engine by inserting one into

the other.

– Fix the cord connector by clamp.

Clamp

Connectors

How to mount the control cable

– Remove the air cleaner cover.

– Put the control cable (8) into the adjusting cable (9). Shift the swivel (10) and

put the cable into the swivel. At this time, be careful that the round hole in the

swivel is oriented toward the fitting at the inner wire end.

– Release the swivel and make sure that the inner wire fitting is placed in the

hole.

– Mount the air cleaner cover.

MOUNTING OF HANDLE

CAUTION: Before doing any work on the brush cutter, always stop the

engine and pull the spark plug connector off the spark plug.

Always wear protective gloves!

CAUTION: Start the brush cutter only after having assembled it completely.

For machines with U Handle models

–Place the handle-fixing metal so that the handle with the control lever will be

positioned on the right (the right-hand grip side) as viewed from the engine

side, and the other handle on the left side.

– Fit the groove of the handle-fixing material to the handle end. Fix provision-

ally the attached metal by hexagon socket bolt supplied.

– Adjust the handle to an easy-to-operate position, and tighten securely the

four hexagon socket bolts uniformly on the right and left by Allen wrench.

For machines with E Handle models

–Temporarily assemble four M5 x 25 socket head bolts (1) on the handle joint

(2) so that the handle (3) with a control lever will come to your right hand

side.

– Adjust the handle to an easy-to handle position and tighten the socket head

bolts (1) with even pressure applied on all of them.

– Fit the control cable (together with the earth cord) to the handle with two

clips (4) and hanger.

– Avoid any tendency of the control cable to loop at the handle bar.

For machines with Loop Handle

– Fix a barrier to the left side of the machine together with the handle for

operator protection.

– Make sure that the grip/barrier assembly is fitted between the spacer and

the arrow mark.

WARNING: Do not remove or shrink the spacer. The spacer keeps a certain

distance between both hands. Setting the grip/barrier assembly

close to the other grip beyond the length of the spacer may cause

loss of control and serious personal injury.

ADJUSTMENT OF CONTROL CABLE

Make adjustment so that the control cable will be provided with a play of 1 to 2

mm, when the throttle lever is set to low speed by carburetor adjusting bolt.

(the blde or the nylon cutting head must not turn when the engine is on idle)

Control cable

Hanger

Adjusting bolt

to Engine

MS-3202

MS-3202 E

MS-3202/3202 E

MS-3212

Arrow mark

To meet the applicable safety provisions, only the tool/ protector combinations as

indicated in the table must be used.

Be sure to use genuine DOLMAR cutter blades or nylon cutting head.

– The cutter blade must be well polished, free of cracks or breakage. If the cutter blade hits

against a stone during operation, stop the engine and check the blade immediately.

– Polish or replace the cutter blade every three hours of operation.

– If the nylon cutting head hits against a stone during operation, stop the engine and check the

nylon cutting head immediately.

MOUNTING OF PROTECTOR

– Fix the protector (1) to the clamp (3) with two bolts M6 x 30 (2).

– When using the string head, fit the protector (6) into the protector (1), and

tighten them with two nuts (5) and two screws (4).

Star Blade

Eddy Blade

Protector for metal blades

Nylon cutting head

Protector for cord cutter

Rotation

Turn the machine upside down, and you can replace the cutter blade or the

nylon cutting head easily.

– Insert the hex wrench through the hole in the gear case and rotate the

receiver washer (3) until it is locked with the hex wrench.

– Loosen the nut (1) (left-hand thread) with the socket wrench and remove

the nut (1), and clamp washer (2).

With the hex wrench still in place.

– Mount the cutter blade onto the shaft so that the guide of the receiver

washer (3) fits in the arbor hole in the cutter blade. Install the clamp washer

(2) and secure the cutter blade with the nut (1).

[Tightening torque: 13 - 23 N-m]

NOTE: Always wear gloves when handling the cutter blade.

NOTE: The cutter blade-fastening nut (with spring washer) is a consumable

part. If there appears any wear or deformation on the spring washer,

replace the nut.

NOTE: The cutter blade-fastening nut (with spring washer) is a consumable

part. If there appears any wear or deformation on the spring washer,

replace the nut.

– Screw the nylon cutting head onto the shaft.

– Make sure that the blade is the left way up.

MOUNTING OF CUTTER BLADE OR NYLON CUTTER HEAD

Hex wrench

Loosen

Tighten

Hex wrench

Loosen

Tighten

Handling fuel

Utmost care is required when handling fuel. Fuel may contain substances

similar to solvents. Refuel either in a well ventilated room or outdoors. Do not

inhale fuel vapors, avoid any contact of fuel or oil with your skin.

Mineral oil products degrease your skin. If your skin comes in contact with

these substances repeatedly and for an extended period of time, it will desiccate.

Various skin diseases may result. In addition, allergic reactions may occur.

Eyes can be irritated by contact with oil. If oil comes into your eyes,

immediately wash them with clear water. If your eyes are still irritated, see a

doctor immediately.

FUELS/REFUELLING

Note: For preparing the fuel-oil mixture first mix the entire oil quantity with half

of the fuel required, then add the remaining fuel. Thoroughly shake the

mixture before filling it into the brush cutter tank. It is not wise to add

more engine oil than specified to ensure safe operation.

This will only result in a higher production of combustion residues which

will pollute the environment and clog the exhaust channel in the cylinder

as well as the muffler. In addition, the fuel consumption will rise and the

performance will decrease.

Fuel and oil mixture

The engine of the brush cutter is a high-efficiency two-stroke engine. It is run

with a mixture of fuel and two-stroke engine oil. The engine is designed for

unleaded regular fuel with a min. octane value of 91 RON. In case no such fuel

is available, you can use fuel with a higher octane value. This will not affect the

engine, but may cause poor operating behaviour.

A similar situation will arise from the use of leaded fuel. To obtain optimum

engine operation and to protect your health and the environment, only unleaded

fuel should be used!

For lubricating the engine use a two-stroke engine oil (quality grade: TC-3),

which is added to the fuel. The engine has been designed to use specified

two-stroke engine oil at mixture ratio of 50:1 to protect the environment. In

addition, a long service life and a reliable operation with a minimum emission of

exhaust gases is guaranteed. It is absolutely essential to observe a mixture

ratio of 50:1 (specified 2-stroke engine oil), as otherwise reliable function of the

brush cutter cannot be guaranteed.

The correct mixture ratio:

Gasoline : Specified two-stroke engine oil = 50 : 1 or

Gasoline : Other manufacturer’s two-stroke engine oil = 25 : 1

recommended

Observe the Safety Instructions on page 3.

Refuelling

The engine must be switched off.

– Thoroughly clean the area around the fuel filler cap (2), to prevent dirt from

getting into the fuel tank (1).

– Unscrew the fuel filler cap (2) and fill the tank with fuel.

– Tightly screw on the fuel filler cap (2).

– Clean screw fuel filler cap (2) and tank after refueling.

Storage of Fuel

Fuel cannot be stored for an unlimited period of time.

Purchase only the quantity required for a 4 week operating period. Only use

approved fuel storage containers.

CORRECT HANDLING OF MACHINE

Attachment of shoulder strap

– Adjust the strap length so that the cutter blade will be kept parallel with the

ground.

Detachment

– In an emergency, push the notches (1) at both sides, and you can detach

the machine from you.

Be extremely careful to maintain control of the machine at this time. Do not

allow the machine to be deflected toward you or anyone in the work

vicinity.

WARNING: Failure to maintain complete control of the machine at all could

result in serious bodily injury or DEATH.

POINTS IN OPERATION AND HOW TO STOP

Observe the applicable accident prevention regulations.

Starting

Move at least 3m away from the place of refuelling. Place the brush cutter on a clean piece of ground taking care that the cutting tool does

not come into contact with the ground or any other objects.

Cold start

– Push the I-O switch (1) in the direction shown by the arrow.

– First place the machine on the ground.

– Give a gentle push on the primer pump (2) repeatedly (7-10 times) until fuel

comes into the primer pump.

– Move the choke lever (3) to the top position ( ).

(1)

Hanger

(3)

(2)

–In case of emergency, remove the emergency detachment lever (2) by

pulling strongly with a finger. The machine sill detach from body.

Be extremely careful to maintain control of the machine at this time. Do not

allow the machine to be deflected toward you or anyone in the work vicinity.

WARNING: Failure to maintain complete control of the machine at all could

result in serious bodily injury or DEATH.

(2)

Hanger

MS-3212

MS-3202/3202 E

STOPPING

– Release the throttle lever (6) fully, and when the engine rpm has lowered,

push the I-O switch (1) to “O”!position the engine will now stop.

– Be aware that the cutting head may not stop immediately and allow it to slow

down fully.

ADJUSTMENT OF LOW-SPEED ROTATION (IDLING)

The cutter blade or the nylon cutting head should not run when the control lever is fully released. If necessary, adjust the idle rpm using the idle

adjusting screw.

Checking the Idling speed

– Idle speed should be set to 2,600 /min.

If necessary correct it by means of the idle screw (the blade or the nylon

cutting head must not turn when the engine is on idle).

Screwing in the screw (1) will cause an increase in the engine speed,

whereas backing off the screw will reduce the engine speed.

RESHARPENING THE CUTTING TOOL

CAUTION : The cutting tools mentioned below must only be resharpened by an

authorized facility. Manual resharpening will result in imbalances of

the cutting tool causing vibrations and damage to the equipment.

– cutter blade (star blade (4 teeth), eddy blade (8 teeth))

– Run the engine for approximately one minute at a moderate speed before applying full throttle.

Note: – If the starter handle is pulled repeatedly when the choke lever remains at “ ” position, the engine will not start easily due to

excessive fuel intake.

– In case of excessive fuel intake, remove the spark plug and pull the starter handle slowly to remove excess fuel. Also,dry the

electrode section of the spark plug.

Caution during operation:

If the throttle lever is opened fully in a no-load operation, the engine rotation is increased to 10,000 /min or more. Never operate the engine at a

higher speed than required and at an approximate speed of 6,000 - 8,000 /min.

Starting the warm engine

– Same as adove, except without moving the choke lever (choke lever remains in the position “ ”.

An expert resharpening and balancing service is provided by Authorized Service

Agents.

NOTE : To increase the service life of the cutter blade (star blade, eddy blade) it

may be turned over once, until both cutting edges have become blunt.

– Firmly hold the clutch case by your left hand, as illustrated.

– Slowly pull the starter grip until resistance is felt and continue with a smart

pull.

– Do not pull out the starter rope to its full extent and do not allow the starter

handle to be retracted without control, but ensure that it is retracted slowly.

– Repeat the starting operation until initial ignitions are heard.

– When the engine start, return the choke lever to “ ”. Please note that the

choke lever will return to “ ”position automatically when the throttle lever is

operated and the throttle is opened.

Idle speed Full speed

NYLON CUTTING HEAD

The nylon cutting head is a dual string trimmer head capable of both automatic

and bump & feed mechanisms.

The nylon cutting head will automatically feed out the proper length of nylon

cord by the changes in centrifugal force caused by increasing or decreasing

rpms. However, to cut soft grass more efficiently, bump the nylon cutting

head against the ground to feed out extra cord as indicated under operation

section.

Operation

– Increase the nylon cutting head speed to approx. 6,000/min.

Low speed (under 4,800/min) is not suitable, the nylon cord will not feed out

properly at low speed.

– The most effective cutting area is shown by the shaded area.

If the nylon cord does not feed out automatically proceed as follows:

1. Release the throttle lever to run the engine idle and then squeeze the

throttle lever fully. Repeat this procedure until the nylon cord feeds out to

the proper length.

2. If the nylon cord is too short to feed out automatically with the above

procedure, bump the knob of the nylon cutting head against the ground to

feed out the nylon cord.

3. If the nylon cord does not feed out with procedure 2, rewind/replace the

nylon cord by following the procedures described under “Replacing the

nylon cord”.

Replacing the nylon cord

– First, stop the engine.

– Press on the housing latches inward to lift off the cover, then remove the

spool.

– Hook the center of new nylon cord into the notch in the center of the spool,

with one end of the cord extending about 80mm (3-1/8") more than the other.

Then wind both ends firmly around the spool in the direction of the head

rotation (left-hand direction indicated by LH and right-hand direction by RH

on the side of the spool).

– Wind all but about 100mm (3-15/16") of the cords, leaving the ends tempo-

rarily hooked through a notch on the side of the spool.

– Mount the spool in the housing so that the grooves and protrusions on the

spool match up with those in the housing. Keep the side with letters on the

spool visible on the top. Now, unhook the ends of the cord from their

temporary position and feed the cords through the eyelets to come out of the

housing.

Most effective cutting area

Idle speed

Full speed

Knob

Cover

Latches

Press

80mm(3-1/8”)

Spool

For left hand rotation

Spool

100mm(3-15/16”)

Notches

Eyelets

– Align the protrusion on the underside of the cover with the slots of the

eyelets.

Then push cover firmly onto the housing to secure it.

Cover

Protrusion

Slot of eyelet

SERVICING INSTRUCTIONS

CAUTION : Before doing any work on the Brush cutter, always switch off the

motor and pull the plug cap off the spark plug (see “checking the

spark plug”).

Always wear protective gloves.

CAUTION : Never remove the recoil starter for yourself, which may cause an

accident.It should be asked to the Authorized Service Agent.

To ensure a long service life and to avoid any damage to the equipment, the following servicing operations should be performed at regular

intervals.

Daily checkup and maintenance

– Before operation, check the machine for loose screws or missing parts. Pay particular attention to the tightness of the cutter blade or

nylon cutting head.

– Before operation, always check for clogging of the cooling air passage and the cylinder fins.

Clean them if necessary.

– Perform the following work daily after use:

• Clean the Brush cutter externally and inspect for damage.

• Clean the air filter. When working under extremely dusty conditions, clean the filter the severall times a day.

• Check the blade or the nylon cutting head for damage and make sure it is firmly mounted.

• Check that there is sufficient difference between idling and engagement speed to ensure that the cutting tool is at a standstill while the

engine is idling (if necessary, reduce idling speed).

If under idling conditions the tool should still continue to run, consult your nearest Authorized Service Agent.

– Check the functioning of the I-O switch, the lock-off lever, the control lever, and the look button.

Cleaning of air cleaner

– Push the choke lever (1) up (arrow), to prevent dirt particles from entering the

carburetor.

– Unscrew screw (2).

– Remove the air cleaner cover (4).

– Take out the sponge element (3), wash it in lukewarm water and dry it

completely.

– After cleaning, put back the air cleaner cover (4) and fasten it with screw (2).

NOTE: If there is excessive dust or dirt adhering to the air cleaner, clean it every

day. A clogged air cleaner may make it difficult or impossible to start the

engine or increase the engine rotational speed.

0.6mm-0.7mm

(0.024”-0.028”)

Suction head in the fuel tank

– The fuel filler (5) of the suction head is used to filler the fuel required by the

carburetor.

– A periodical visual inspection of the fuel filter is to be conducted. For that

purpose open the tank cap, use a wire hook and pull out the suction head

through the tank opening. Filters found to have hardened, been polluted or

clogged up are to be replaced.

– Insufficient fuel supply can result in the admissible maximum speed being

exceeded. It is therefore important to replace the fuel filter at least quarterly

to ensure satisfactory fuel supply to the carburetor.

Checking the spark plug

– Only use the supplied universal wrench to remove or to install the spark plug.

– The gap between the two electrodes of the spark plug should be 0.6-0.7mm

(0.024”-0.028”). If the gap is too wide or too narrow, adjust it. If the spark

plug is clogged with carton or fouled, clean it thoroubhly or replace it.

CAUTION : Never touch the spark plug connector while the engine is running

(danger of high voltage electric shock).

Supply of grease to gear case

– Supply grease (Shell Alvania 3 or equivalent) to the gear case through the

grease hole every 30 hours. (Genuine DOLMAR grease may be purchased

from your DOLMAR dealer.)

Any maintenance of adjustment work that is not included and described in this manual is only to be performed by Authorized Service Agents.

Cleaning of muffler exhaust port

– Check of muffler exhaust port (6) regularly.

– If it is clogged by carbon deposits, carefully scratch the deposits out with a

suitable tool.

Gear case

Grease hole

STORAGE

Fault location

– When the machine is in storage for a long time, drain fuel from the fuel tank

and carburetor, as follows: Drain all fuel from the fuel tank. Dispose of

properly and in accordance with all local laws.

– Remove the spark plug and a few drops of oil into the spark plug hole.

Then, pull the starter gently, so that oil covers the engine inside and tighten

the spark plug.

– Clear dirt or dust from the cutter blade and outside of engine, wipe them

with a oil-immersed cloth and keep the machine in a place as dry as

possible.

Drain fuel

Humidity

Maintenance schedule

General

Engine assembly, screws and

nuts

Visual inspection for damage and tightness

Check for general condition and security

After each refuelling

Control lever

I-O switch

Functional check

Daily

Air filter

Cooling air duct

Cutting tool

Idling speed

To be cleaned

Check for damage and sharpness

Inspection (cutting tool must not move)

Weekly

Spark plug

Muffler

Inspection, replace if necessary

Check and if necessary clean the opening

Quarterly

Suction head

Fuel tank

To be replaced

To be cleaned

Shuting down procedure

Fuel tank

Carburetor

Empty fuel tank

Operate until engine runs out of fuel

Fault System Observation Cause

Engine not starting or with

difficulty

Ignition system Ignition spark O.K.

Fault in fuel supply or compression system, mechanical

defect

No ignition spark

I-O switch operated, wiring fault or short circuit, spark

plug or connector defective, ignition module faulty

Fuel supply Fuel tank filled

Incorrect choke position, carburetor defective, fuel supply

line bent or blocked, fuel dirty.

Compression

No compression when

pulled over

Cylinder bottom gasket defective, crankshaft seals

damaged, cylinder or piston rings defective or improper

sealing of spark plug

Mechanical fault Starter not engaging Broken starter spring, broken parts inside of the engine

Warm start problems

Tank filled ignition spark

existing

Carburetor contaminated, must be cleaned

Engine starts but dies Fuel supply Tank filled Incorrect idling adjustment, carburetor contaminated

Fuel tank vent defective, fuel supply line interrupted,

cable or I-O switch faulty

Insufficient performance

Several systems

may simultaneously

be affected

Engine idling poor

Air filter contaminated, carburetor contaminated, muffler

clogged, exhaust duct in the cylinder clogged

La pagina sta caricando ...

Makita MS-3202E Manuale utente

Marca: Makita

Modello: MS-3202E

Categoria: Tagliaerba

Tipo: Manuale utente

Questo manuale è adatto anche per

Scarica il pdf

rapporto

in altre lingue

English: Makita MS-3202E User manual
español: Makita MS-3202E Manual de usuario
português: Makita MS-3202E Manual do usuário

Makita MS-3202E Manuale utente

Questo manuale è adatto anche per

Makita MS-3202E Manuale utente

in altre lingue

Documenti correlati

Altri documenti