Juniper SRX100 Manuale utente

Categoria
Networking
Tipo
Manuale utente
SRX100 Services Gateway
Hardware Guide
Juniper Networks, Inc.
1194 North Mathilda Avenue
Sunnyvale, California 94089
USA
408-745-2000
www.juniper.net
Published: 2009-08-19
This product includes the Envoy SNMP Engine, developed by Epilogue Technology, an Integrated Systems Company. Copyright © 1986-1997, Epilogue
Technology Corporation. All rights reserved. This program and its documentation were developed at private expense, and no part of them is in the public
domain.
This product includes memory allocation software developed by Mark Moraes, copyright © 1988, 1989, 1993, University of Toronto.
This product includes FreeBSD software developed by the University of California, Berkeley, and its contributors. All of the documentation and software
included in the 4.4BSD and 4.4BSD-Lite Releases is copyrighted by the Regents of the University of California. Copyright © 1979, 1980, 1983, 1986, 1988,
1989, 1991, 1992, 1993, 1994. The Regents of the University of California. All rights reserved.
GateD software copyright © 1995, the Regents of the University. All rights reserved. Gate Daemon was originated and developed through release 3.0 by
Cornell University and its collaborators. Gated is based on Kirtons EGP, UC Berkeleys routing daemon (routed), and DCNs HELLO routing protocol.
Development of Gated has been supported in part by the National Science Foundation. Portions of the GateD software copyright © 1988, Regents of the
University of California. All rights reserved. Portions of the GateD software copyright © 1991, D. L. S. Associates.
This product includes software developed by Maker Communications, Inc., copyright © 1996, 1997, Maker Communications, Inc.
Juniper Networks, the Juniper Networks logo, JUNOS, NetScreen, ScreenOS, and Steel-Belted Radius are registered trademarks of Juniper Networks, Inc. in
the United States and other countries. JUNOSe is a trademark of Juniper Networks, Inc. All other trademarks, service marks, registered trademarks, or
registered service marks are the property of their respective owners.
Juniper Networks assumes no responsibility for any inaccuracies in this document. Juniper Networks reserves the right to change, modify, transfer, or
otherwise revise this publication without notice.
Products made or sold by Juniper Networks or components thereof might be covered by one or more of the following patents that are owned by or licensed
to Juniper Networks: U.S. Patent Nos. 5,473,599, 5,905,725, 5,909,440, 6,192,051, 6,333,650, 6,359,479, 6,406,312, 6,429,706, 6,459,579, 6,493,347,
6,538,518, 6,538,899, 6,552,918, 6,567,902, 6,578,186, and 6,590,785.
SRX100 Services Gateway Hardware Guide
Copyright © 2009, Juniper Networks, Inc.
All rights reserved. Printed in USA.
Revision History
August 2009Revision 01
The information in this document is current as of the date listed in the revision history.
SOFTWARE LICENSE
The terms and conditions for using this software are described in the software license contained in the acknowledgment to your purchase order or, to the
extent applicable, to any reseller agreement or end-user purchase agreement executed between you and Juniper Networks. By using this software, you
indicate that you understand and agree to be bound by those terms and conditions.
Generally speaking, the software license restricts the manner in which you are permitted to use the software and may contain prohibitions against certain
uses. The software license may state conditions under which the license is automatically terminated. You should consult the license for further details.
For complete product documentation, please see the Juniper Networks Web site at www.juniper.net/techpubs.
ii
END USER LICENSE AGREEMENT
READ THIS END USER LICENSE AGREEMENT (AGREEMENT) BEFORE DOWNLOADING, INSTALLING, OR USING THE SOFTWARE. BY DOWNLOADING,
INSTALLING, OR USING THE SOFTWARE OR OTHERWISE EXPRESSING YOUR AGREEMENT TO THE TERMS CONTAINED HEREIN, YOU (AS CUSTOMER
OR IF YOU ARE NOT THE CUSTOMER, AS A REPRESENTATIVE/AGENT AUTHORIZED TO BIND THE CUSTOMER) CONSENT TO BE BOUND BY THIS
AGREEMENT. IF YOU DO NOT OR CANNOT AGREE TO THE TERMS CONTAINED HEREIN, THEN (A) DO NOT DOWNLOAD, INSTALL, OR USE THE SOFTWARE,
AND (B) YOU MAY CONTACT JUNIPER NETWORKS REGARDING LICENSE TERMS.
1. The Parties. The parties to this Agreement are (i) Juniper Networks, Inc. (if the Customers principal office is located in the Americas) or Juniper Networks
(Cayman) Limited (if the Customers principal office is located outside the Americas) (such applicable entity being referred to herein as Juniper), and (ii)
the person or organization that originally purchased from Juniper or an authorized Juniper reseller the applicable license(s) for use of the Software (Customer)
(collectively, the Parties).
2. The Software. In this Agreement, Software means the program modules and features of the Juniper or Juniper-supplied software, for which Customer
has paid the applicable license or support fees to Juniper or an authorized Juniper reseller, or which was embedded by Juniper in equipment which Customer
purchased from Juniper or an authorized Juniper reseller. Software also includes updates, upgrades and new releases of such software. Embedded
Software means Software which Juniper has embedded in or loaded onto the Juniper equipment and any updates, upgrades, additions or replacements
which are subsequently embedded in or loaded onto the equipment.
3. License Grant. Subject to payment of the applicable fees and the limitations and restrictions set forth herein, Juniper grants to Customer a non-exclusive
and non-transferable license, without right to sublicense, to use the Software, in executable form only, subject to the following use restrictions:
a. Customer shall use Embedded Software solely as embedded in, and for execution on, Juniper equipment originally purchased by Customer from Juniper
or an authorized Juniper reseller.
b. Customer shall use the Software on a single hardware chassis having a single processing unit, or as many chassis or processing units for which Customer
has paid the applicable license fees; provided, however, with respect to the Steel-Belted Radius or Odyssey Access Client software only, Customer shall use
such Software on a single computer containing a single physical random access memory space and containing any number of processors. Use of the
Steel-Belted Radius or IMS AAA software on multiple computers or virtual machines (e.g., Solaris zones) requires multiple licenses, regardless of whether
such computers or virtualizations are physically contained on a single chassis.
c. Product purchase documents, paper or electronic user documentation, and/or the particular licenses purchased by Customer may specify limits to
Customers use of the Software. Such limits may restrict use to a maximum number of seats, registered endpoints, concurrent users, sessions, calls,
connections, subscribers, clusters, nodes, realms, devices, links, ports or transactions, or require the purchase of separate licenses to use particular features,
functionalities, services, applications, operations, or capabilities, or provide throughput, performance, configuration, bandwidth, interface, processing,
temporal, or geographical limits. In addition, such limits may restrict the use of the Software to managing certain kinds of networks or require the Software
to be used only in conjunction with other specific Software. Customers use of the Software shall be subject to all such limitations and purchase of all applicable
licenses.
d. For any trial copy of the Software, Customers right to use the Software expires 30 days after download, installation or use of the Software. Customer
may operate the Software after the 30-day trial period only if Customer pays for a license to do so. Customer may not extend or create an additional trial
period by re-installing the Software after the 30-day trial period.
e. The Global Enterprise Edition of the Steel-Belted Radius software may be used by Customer only to manage access to Customers enterprise network.
Specifically, service provider customers are expressly prohibited from using the Global Enterprise Edition of the Steel-Belted Radius software to support any
commercial network access services.
The foregoing license is not transferable or assignable by Customer. No license is granted herein to any user who did not originally purchase the applicable
license(s) for the Software from Juniper or an authorized Juniper reseller.
4. Use Prohibitions. Notwithstanding the foregoing, the license provided herein does not permit the Customer to, and Customer agrees not to and shall
not: (a) modify, unbundle, reverse engineer, or create derivative works based on the Software; (b) make unauthorized copies of the Software (except as
necessary for backup purposes); (c) rent, sell, transfer, or grant any rights in and to any copy of the Software, in any form, to any third party; (d) remove
any proprietary notices, labels, or marks on or in any copy of the Software or any product in which the Software is embedded; (e) distribute any copy of
the Software to any third party, including as may be embedded in Juniper equipment sold in the secondhand market; (f) use any locked or key-restricted
feature, function, service, application, operation, or capability without first purchasing the applicable license(s) and obtaining a valid key from Juniper, even
if such feature, function, service, application, operation, or capability is enabled without a key; (g) distribute any key for the Software provided by Juniper
to any third party; (h) use the Software in any manner that extends or is broader than the uses purchased by Customer from Juniper or an authorized Juniper
reseller; (i) use Embedded Software on non-Juniper equipment; (j) use Embedded Software (or make it available for use) on Juniper equipment that the
Customer did not originally purchase from Juniper or an authorized Juniper reseller; (k) disclose the results of testing or benchmarking of the Software to
any third party without the prior written consent of Juniper; or (l) use the Software in any manner other than as expressly provided herein.
5. Audit. Customer shall maintain accurate records as necessary to verify compliance with this Agreement. Upon request by Juniper, Customer shall furnish
such records to Juniper and certify its compliance with this Agreement.
iii
6. Confidentiality. The Parties agree that aspects of the Software and associated documentation are the confidential property of Juniper. As such, Customer
shall exercise all reasonable commercial efforts to maintain the Software and associated documentation in confidence, which at a minimum includes
restricting access to the Software to Customer employees and contractors having a need to use the Software for Customers internal business purposes.
7. Ownership. Juniper and Junipers licensors, respectively, retain ownership of all right, title, and interest (including copyright) in and to the Software,
associated documentation, and all copies of the Software. Nothing in this Agreement constitutes a transfer or conveyance of any right, title, or interest in
the Software or associated documentation, or a sale of the Software, associated documentation, or copies of the Software.
8. Warranty, Limitation of Liability, Disclaimer of Warranty. The warranty applicable to the Software shall be as set forth in the warranty statement that
accompanies the Software (the Warranty Statement). Nothing in this Agreement shall give rise to any obligation to support the Software. Support services
may be purchased separately. Any such support shall be governed by a separate, written support services agreement. TO THE MAXIMUM EXTENT PERMITTED
BY LAW, JUNIPER SHALL NOT BE LIABLE FOR ANY LOST PROFITS, LOSS OF DATA, OR COSTS OR PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES,
OR FOR ANY SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES ARISING OUT OF THIS AGREEMENT, THE SOFTWARE, OR ANY JUNIPER OR
JUNIPER-SUPPLIED SOFTWARE. IN NO EVENT SHALL JUNIPER BE LIABLE FOR DAMAGES ARISING FROM UNAUTHORIZED OR IMPROPER USE OF ANY
JUNIPER OR JUNIPER-SUPPLIED SOFTWARE. EXCEPT AS EXPRESSLY PROVIDED IN THE WARRANTY STATEMENT TO THE EXTENT PERMITTED BY LAW,
JUNIPER DISCLAIMS ANY AND ALL WARRANTIES IN AND TO THE SOFTWARE (WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE), INCLUDING
ANY IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NONINFRINGEMENT. IN NO EVENT DOES JUNIPER
WARRANT THAT THE SOFTWARE, OR ANY EQUIPMENT OR NETWORK RUNNING THE SOFTWARE, WILL OPERATE WITHOUT ERROR OR INTERRUPTION,
OR WILL BE FREE OF VULNERABILITY TO INTRUSION OR ATTACK. In no event shall Junipers or its suppliers or licensors liability to Customer, whether
in contract, tort (including negligence), breach of warranty, or otherwise, exceed the price paid by Customer for the Software that gave rise to the claim, or
if the Software is embedded in another Juniper product, the price paid by Customer for such other product. Customer acknowledges and agrees that Juniper
has set its prices and entered into this Agreement in reliance upon the disclaimers of warranty and the limitations of liability set forth herein, that the same
reflect an allocation of risk between the Parties (including the risk that a contract remedy may fail of its essential purpose and cause consequential loss),
and that the same form an essential basis of the bargain between the Parties.
9. Termination. Any breach of this Agreement or failure by Customer to pay any applicable fees due shall result in automatic termination of the license
granted herein. Upon such termination, Customer shall destroy or return to Juniper all copies of the Software and related documentation in Customers
possession or control.
10. Taxes. All license fees payable under this agreement are exclusive of tax. Customer shall be responsible for paying Taxes arising from the purchase of
the license, or importation or use of the Software. If applicable, valid exemption documentation for each taxing jurisdiction shall be provided to Juniper prior
to invoicing, and Customer shall promptly notify Juniper if their exemption is revoked or modified. All payments made by Customer shall be net of any
applicable withholding tax. Customer will provide reasonable assistance to Juniper in connection with such withholding taxes by promptly: providing Juniper
with valid tax receipts and other required documentation showing Customers payment of any withholding taxes; completing appropriate applications that
would reduce the amount of withholding tax to be paid; and notifying and assisting Juniper in any audit or tax proceeding related to transactions hereunder.
Customer shall comply with all applicable tax laws and regulations, and Customer will promptly pay or reimburse Juniper for all costs and damages related
to any liability incurred by Juniper as a result of Customers non-compliance or delay with its responsibilities herein. Customers obligations under this
Section shall survive termination or expiration of this Agreement.
11. Export. Customer agrees to comply with all applicable export laws and restrictions and regulations of any United States and any applicable foreign
agency or authority, and not to export or re-export the Software or any direct product thereof in violation of any such restrictions, laws or regulations, or
without all necessary approvals. Customer shall be liable for any such violations. The version of the Software supplied to Customer may contain encryption
or other capabilities restricting Customers ability to export the Software without an export license.
12. Commercial Computer Software. The Software is commercial computer software and is provided with restricted rights. Use, duplication, or disclosure
by the United States government is subject to restrictions set forth in this Agreement and as provided in DFARS 227.7201 through 227.7202-4, FAR 12.212,
FAR 27.405(b)(2), FAR 52.227-19, or FAR 52.227-14(ALT III) as applicable.
13. Interface Information. To the extent required by applicable law, and at Customer's written request, Juniper shall provide Customer with the interface
information needed to achieve interoperability between the Software and another independently created program, on payment of applicable fee, if any.
Customer shall observe strict obligations of confidentiality with respect to such information and shall use such information in compliance with any applicable
terms and conditions upon which Juniper makes such information available.
14. Third Party Software. Any licensor of Juniper whose software is embedded in the Software and any supplier of Juniper whose products or technology
are embedded in (or services are accessed by) the Software shall be a third party beneficiary with respect to this Agreement, and such licensor or vendor
shall have the right to enforce this Agreement in its own name as if it were Juniper. In addition, certain third party software may be provided with the
Software and is subject to the accompanying license(s), if any, of its respective owner(s). To the extent portions of the Software are distributed under and
subject to open source licenses obligating Juniper to make the source code for such portions publicly available (such as the GNU General Public License
(GPL) or the GNU Library General Public License (LGPL)), Juniper will make such source code portions (including Juniper modifications, as appropriate)
available upon request for a period of up to three years from the date of distribution. Such request can be made in writing to Juniper Networks, Inc., 1194
N. Mathilda Ave., Sunnyvale, CA 94089, ATTN: General Counsel. You may obtain a copy of the GPL at http://www.gnu.org/licenses/gpl.html, and
a copy of the LGPL at http://www.gnu.org/licenses/lgpl.html.
15. Miscellaneous. This Agreement shall be governed by the laws of the State of California without reference to its conflicts of laws principles. The provisions
of the U.N. Convention for the International Sale of Goods shall not apply to this Agreement. For any disputes arising under this Agreement, the Parties
hereby consent to the personal and exclusive jurisdiction of, and venue in, the state and federal courts within Santa Clara County, California. This Agreement
constitutes the entire and sole agreement between Juniper and the Customer with respect to the Software, and supersedes all prior and contemporaneous
iv
agreements relating to the Software, whether oral or written (including any inconsistent terms contained in a purchase order), except that the terms of a
separate written agreement executed by an authorized Juniper representative and Customer shall govern to the extent such terms are inconsistent or conflict
with terms contained herein. No modification to this Agreement nor any waiver of any rights hereunder shall be effective unless expressly assented to in
writing by the party to be charged. If any portion of this Agreement is held invalid, the Parties agree that such invalidity shall not affect the validity of the
remainder of this Agreement. This Agreement and associated documentation has been written in the English language, and the Parties agree that the English
version will govern. (For Canada: Les parties aux présentés confirment leur volonté que cette convention de même que tous les documents y compris tout
avis qui s'y rattaché, soient redigés en langue anglaise. (Translation: The parties confirm that this Agreement and all related documentation is and will be
in the English language)).
v
vi
Table of Contents
About This Guide xiii
Objectives .....................................................................................................xiii
Audience ......................................................................................................xiii
Documentation Conventions ........................................................................xiii
SRX Series Documentation and Release Notes ..............................................xv
Obtaining Documentation .............................................................................xv
Documentation Feedback .............................................................................xvi
Requesting Technical Support .......................................................................xvi
Part 1 SRX100 Services Gateway Overview
Chapter 1 Introduction to the SRX100 Services Gateway 3
SRX100 Services Gateway Description ............................................................3
About the SRX100 Services Gateway ........................................................3
Accessing the SRX100 Services Gateway ..................................................3
SRX100 Services Gateway Features and Functions ..........................................4
Chapter 2 SRX100 Services Gateway Hardware Components and
Specifications 5
SRX100 Services Gateway Specifications .........................................................5
SRX100 Services Gateway Front Panel and Back Panel Views .........................6
SRX100 Services Gateway Front Panel .....................................................6
SRX100 Services Gateway Back Panel ......................................................7
SRX100 Services Gateway Built-In Interfaces ..................................................8
SRX100 Services Gateway LEDs ....................................................................10
SRX100 Services Gateway Front Panel LEDs ...........................................10
SRX100 Services Gateway Ethernet Port LEDs ........................................12
SRX100 Services Gateway Boot Devices ........................................................13
SRX100 Services Gateway Power Supply .......................................................13
Table of Contents vii
Part 2 Setting Up the SRX100 Services Gateway
Chapter 3 Preparing the Site for SRX100 Services Gateway Installation 17
Site Preparation Checklist for the SRX100 Services Gateway .........................17
General Site Guidelines for Installing the SRX100 Services Gateway ..............19
SRX100 Services Gateway Cabinet Requirements .........................................20
SRX100 Services Gateway Rack Requirements ..............................................21
Clearance Requirements for Airflow and Hardware Maintenance of the
SRX100 Services Gateway ......................................................................22
SRX100 Services Gateway Electrical and Power Requirements .....................23
Chapter 4 Installation Overview for the SRX100 Services Gateway 25
Installation Overview for the SRX100 Services Gateway ................................26
Chapter 5 Required Tools and Parts for Installing and Maintaining the SRX100
Services Gateway 29
Required Tools and Parts for Installing and Maintaining the SRX100 Services
Gateway ..................................................................................................29
Chapter 6 Unpacking the SRX100 Services Gateway 31
Unpacking the SRX100 Services Gateway .....................................................31
Verifying Parts Received with the SRX100 Services Gateway ........................32
Chapter 7 Preparing the SRX100 Services Gateway for Installation 35
Preparing the SRX100 Services Gateway for Rack-Mount Installation ............35
Preparing the SRX100 Services Gateway for Desk-Mount Installation ............36
Preparing the SRX100 Services Gateway for Wall-Mount Installation ............37
Chapter 8 Installing the SRX100 Services Gateway 39
SRX100 Services Gateway Safety Requirements, Warnings, and
Guidelines ...............................................................................................39
Installing the SRX100 Services Gateway ........................................................39
Installing the SRX100 Services Gateway in a Rack ..................................40
Installing the SRX100 Services Gateway on a Desk .................................42
Installing the SRX100 Services Gateway on a Wall ..................................43
viii Table of Contents
SRX100 Services Gateway Hardware Guide
Chapter 9 Connecting, Grounding, and Powering On the SRX100 Services
Gateway 45
Connecting the SRX100 Services Gateway to the Power Supply ....................45
Connecting and Organizing Interface Cables to the SRX100 Services
Gateway ..................................................................................................46
Grounding the SRX100 Services Gateway ......................................................47
Powering On and Powering Off the SRX100 Services Gateway .....................48
Powering On the SRX100 Services Gateway ...........................................48
Powering Off the SRX100 Services Gateway ...........................................49
Chapter 10 SRX100 Services Gateway Memory Upgrade 51
Upgrading the SRX100 Services Gateway Low Memory Version to a High
Memory Version .....................................................................................51
Chapter 11 SRX100 Services Gateway Autoinstallation 53
SRX100 Services Gateway Autoinstallation Overview ....................................53
Chapter 12 Establishing Basic Connectivity for the SRX100 Services
Gateway 55
SRX100 Services Gateway Basic Connectivity ...............................................55
SRX100 Services Gateway Basic Connectivity Overview .........................55
SRX100 Services Gateway Basic Connectivity Settings ............................56
Built-In Ethernet Ports for the SRX100 Services Gateway ........................58
Management Access for the SRX100 Services Gateway ..........................59
Connecting to an SRX100 Services Gateway .................................................60
Connecting an SRX100 Services Gateway to the J-Web Interface ............60
Connecting an SRX100 Services Gateway to the CLI Locally ...................62
Connecting an SRX100 Services Gateway to the CLI Remotely ...............64
Connecting the Modem at the SRX100 Services Gateway End ................64
Connecting the Modem to the Console Port on the SRX100 Services
Gateway ...........................................................................................65
Connecting to the CLI at the User End for the SRX100 Services
Gateway ...........................................................................................66
Configuring Basic Connectivity Settings on the SRX100 Services
Gateway ..................................................................................................67
Configuring Basic Settings for the SRX100 Services Gateway with J-Web
Quick Configuration .........................................................................67
Configuring Basic Settings for the SRX100 Services Gateway with a
Configuration Editor .........................................................................70
Displaying Basic Connectivity Configurations for the SRX100 Services
Gateway ...........................................................................................73
SRX100 Services Gateway Secure Web Access Overview ........................74
Table of Contents ix
Table of Contents
Part 3 SRX100 Services Gateway Hardware Maintenance,
Replacement, and Monitoring Procedures
Chapter 13 Maintaining the SRX100 Services Gateway Hardware
Components 77
Maintaining the SRX100 Services Gateway Hardware Components ..............77
Chapter 14 Monitoring the SRX100 Services Gateway 79
Monitoring the Hardware Components on the SRX100 Services Gateway .....79
Monitoring the SRX100 Services Gateway Chassis Using the CLI ............79
Monitoring the SRX100 Services Gateway Components Using LEDs .......81
Monitoring the SRX100 Services Gateway Using Chassis Alarm
Conditions ........................................................................................83
Monitoring the SRX100 Services Gateway Power System .......................84
Resetting the Configuration File When the SRX100 Services Gateway Is
Inaccessible ............................................................................................85
Using the Reset Config Button on the SRX100 Services Gateway ............85
Changing the Reset Config Button Behavior on the SRX100 Services
Gateway ...........................................................................................86
Juniper Networks Technical Assistance Center ..............................................86
Juniper Networks Technical Assistance Center ........................................87
Part 4 Appendixes
Appendix A Safety and Regulatory Compliance Information 91
SRX100 Services Gateway Definition of Safety Warning Levels .....................91
SRX100 Services Gateway General Safety Guidelines and Warnings ..............93
SRX100 Services Gateway Fire Safety Requirements .....................................96
SRX100 Services Gateway Installation Safety Guidelines and Warnings ........97
SRX100 Services Gateway Laser and LED Safety Guidelines and
Warnings ..............................................................................................101
Laser and LED Safety Guidelines and Warnings ....................................102
General Laser Safety Guidelines ......................................................102
Class 1 Laser Product Warning .......................................................102
Class 1 LED Product Warning .........................................................102
Laser Beam Warning ......................................................................103
Radiation from Open Port Apertures Warning ................................104
SRX100 Services Gateway Maintenance and Operational Safety Guidelines
and Warnings .......................................................................................105
Safety Guidelines and Warnings ............................................................105
Battery Handling Warning ..............................................................105
Jewelry Removal Warning ..............................................................106
Lightning Activity Warning .............................................................107
x Table of Contents
SRX100 Services Gateway Hardware Guide
Operating Temperature Warning ....................................................107
Product Disposal Warning ..............................................................109
SRX100 Services Gateway Electrical Safety Guidelines and Warnings .........109
Electrical Safety Guidelines and Warnings ............................................110
In Case of Electrical Accident .........................................................110
General Electrical Safety Guidelines and Warnings .........................110
SRX100 Services Gateway Agency Approvals ..............................................111
SRX100 Services Gateway Compliance Statements for EMC
Requirements .......................................................................................112
SRX100 Services Gateway Compliance Statements for Environmental
Requirements .......................................................................................113
Appendix B SRX100 Services Gateway Power Guidelines, Requirements, and
Specifications 115
SRX100 Services Gateway Site Electrical Wiring Guidelines .........................115
SRX100 Services Gateway Power Specifications and Requirements ............116
Appendix C SRX100 Services Gateway Interface Cable Specifications and
Connector Pinouts 119
Interface Cable and Wire Specifications for the SRX100 Services
Gateway ................................................................................................119
RJ-45 Connector Pinouts for the SRX100 Services Gateway Ethernet Port ....120
RJ-45 Connector Pinouts for the SRX100 Services Gateway Console Port ....120
Appendix D Contacting Customer Support and Returning the SRX100 Services
Gateway Hardware 123
Return Procedure for the SRX100 Services Gateway ...................................123
Locating the SRX100 Services Gateway Component Serial Number and
Agency Labels .......................................................................................124
Contacting Customer Support to Obtain a Return Materials
Authorization ........................................................................................125
Information You Might Need to Supply to Juniper Networks Technical
Assistance Center ...........................................................................125
Contacting Customer Support ...............................................................126
Packing the SRX100 Services Gateway and Components for
Shipment ........................................................................................126
Part 5 Index
Index ...........................................................................................................131
Table of Contents xi
Table of Contents
xii Table of Contents
SRX100 Services Gateway Hardware Guide
About This Guide
This topic includes the following sections:
Objectives on page xiii
Audience on page xiii
Documentation Conventions on page xiii
SRX Series Documentation and Release Notes on page xv
Obtaining Documentation on page xv
Documentation Feedback on page xvi
Requesting Technical Support on page xvi
Objectives
This guide describes hardware components and installation, basic configuration, and
basic troubleshooting procedures for the Juniper Networks SRX100 Services Gateway.
It explains how to prepare your site for the services gateway installation, unpack and
install the hardware, power on the services gateway, perform initial software
configuration, and perform routine maintenance. After completing the installation
and basic configuration procedures covered in this guide, see the JUNOS Software
configuration guides for information about further JUNOS Software configuration.
Audience
This guide is designed for network administrators who are installing and maintaining
a Juniper Networks SRX100 Services Gateway or preparing a site for device
installation. To use this guide, you need a broad understanding of networks in general
and the Internet in particular, networking principles, and network configuration. Any
detailed discussion of these concepts is beyond the scope of this guide.
Documentation Conventions
Table 1 on page xiv defines the notice icons used in this guide.
Objectives xiii
Table 1: Notice Icons
DescriptionMeaningIcon
Indicates important features or instructions.Informational note
Indicates a situation that might result in loss of data or hardware damage.Caution
Alerts you to the risk of personal injury or death.Warning
Alerts you to the risk of personal injury from a laser.Laser warning
Table 2 on page xiv defines the text and syntax conventions used in this guide.
Table 2: Text and Syntax Conventions
ExamplesDescriptionConvention
To enter configuration mode, type the
configure command:
user@host> configure
Represents text that you type.
Bold text like this
user@host> show chassis alarms
No alarms currently active
Represents output that appears on the
terminal screen.
Fixed-width text like this
A policy term is a named structure
that defines match conditions and
actions.
JUNOS System Basics Configuration
Guide
RFC 1997, BGP Communities
Attribute
Introduces important new terms.
Identifies book names.
Identifies RFC and Internet draft
titles.
Italic text like this
Configure the machines domain name:
[edit]
root@# set system domain-name
domain-name
Represents variables (options for which
you substitute a value) in commands or
configuration statements.
Italic text like this
To configure a stub area, include
the stub statement at the [edit
protocols ospf area area-id]
hierarchy level.
The console port is labeled
CONSOLE.
Represents names of configuration
statements, commands, files, and
directories; IP addresses; configuration
hierarchy levels; or labels on routing
platform components.
Plain text like this
stub <default-metric metric>;
Enclose optional keywords or variables.< > (angle brackets)
xiv Documentation Conventions
SRX100 Services Gateway Hardware Guide
Table 2: Text and Syntax Conventions (continued)
ExamplesDescriptionConvention
broadcast | multicast
(string1 | string2 | string3)
Indicates a choice between the mutually
exclusive keywords or variables on either
side of the symbol. The set of choices is
often enclosed in parentheses for clarity.
| (pipe symbol)
rsvp { # Required for dynamic MPLS only
Indicates a comment specified on the
same line as the configuration statement
to which it applies.
# (pound sign)
community name members [
community-ids ]
Enclose a variable for which you can
substitute one or more values.
[ ] (square brackets)
[edit]
routing-options {
static {
route default {
nexthop address;
retain;
}
}
}
Identify a level in the configuration
hierarchy.
Indention and braces ( { } )
Identifies a leaf statement at a
configuration hierarchy level.
; (semicolon)
J-Web GUI Conventions
In the Logical Interfaces box, select
All Interfaces.
To cancel the configuration, click
Cancel.
Represents J-Web graphical user
interface (GUI) items you click or select.
Bold text like this
In the configuration editor hierarchy,
select Protocols>Ospf.
Separates levels in a hierarchy of J-Web
selections.
> (bold right angle bracket)
SRX Series Documentation and Release Notes
For a list of related SRX Series documentation, see
http://www.juniper.net/techpubs/hardware/srx-series-main.html.
If the information in the latest SRX Series Release Notes differs from the information
in the documentation, follow the SRX Series Release Notes.
Obtaining Documentation
To obtain the most current version of all Juniper Networks technical documentation,
see the products documentation page on the Juniper Networks website at
http://www.juniper.net/techpubs.
To order printed copies of this guide and other Juniper Networks technical documents,
or to order a documentation CD, which contains this guide, contact your sales
representative.
SRX Series Documentation and Release Notes xv
About This Guide
Copies of the Management Information Bases (MIBs) available in a software release
are included on the documentation CDs and at http://www.juniper.net.
Documentation Feedback
We encourage you to provide feedback, comments, and suggestions so that we can
improve the documentation. You can send your comments to
[email protected], or fill out the documentation feedback form at
http://www.juniper.net/techpubs/docbug/docbugreport.html. If you are using e-mail, be sure
to include the following information with your comments:
Document name
Document part number
Page number
Software release version (not required for Network Operations Guides [NOGs])
Requesting Technical Support
Technical product support is available through the Juniper Networks Technical
Assistance Center (JTAC). If you are a customer with an active J-Care or JNASC support
contract, or are covered under warranty, and need postsales technical support, you
can access our tools and resources online or open a case with JTAC.
JTAC policiesFor a complete understanding of our JTAC procedures and policies,
review the JTAC User Guide, located at
http://www.juniper.net/customers/support/downloads/710059.pdf.
Product warrantiesFor product warranty information, visit
http://www.juniper.net/support/warranty/.
JTAC Hours of OperationThe JTAC centers have resources available 24 hours
a day, 7 days a week, 365 days a year.
Self-Help Online Tools and Resources
For quick and easy problem resolution, Juniper Networks has designed an online
self-service portal called the Customer Support Center (CSC) that provides you with
the following features:
Find CSC offerings: http://www.juniper.net/customers/support/
Search for known bugs: http://www2.juniper.net/kb/
Find product documentation: http://www.juniper.net/techpubs/
Find solutions and answer questions using our Knowledge Base:
http://kb.juniper.net/
Download the latest versions of software and review release notes:
http://www.juniper.net/customers/csc/software/
Search technical bulletins for relevant hardware and software notifications:
https://www.juniper.net/alerts/
xvi Documentation Feedback
SRX100 Services Gateway Hardware Guide
Join and participate in the Juniper Networks Community Forum:
http://www.juniper.net/company/communities/
Open a case online in the CSC Case Manager: http://www.juniper.net/cm/
To verify service entitlement by product serial number, use our Serial Number
Entitlement (SNE) tool located at https://tools.juniper.net/SerialNumberEntitlementSearch/.
Opening a Case with JTAC
You can open a case with JTAC on the Web or by telephone.
Use the Case Manager tool in the CSC at http://www.juniper.net/cm/.
Call 1-888-314-JTAC (1-888-314-5822 toll-free in the USA, Canada, and Mexico).
For international or direct-dial options in countries without toll-free numbers, visit
us at http://www.juniper.net/support/requesting-support.html.
Requesting Technical Support xvii
About This Guide
xviii Requesting Technical Support
SRX100 Services Gateway Hardware Guide
Part 1
SRX100 Services Gateway Overview
Introduction to the SRX100 Services Gateway on page 3
SRX100 Services Gateway Hardware Components and Specifications on page 5
SRX100 Services Gateway Overview 1
2 SRX100 Services Gateway Overview
SRX100 Services Gateway Hardware Guide
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154

Juniper SRX100 Manuale utente

Categoria
Networking
Tipo
Manuale utente

in altre lingue