Logan FRAMER'S EDGE PROFESSIONAL Serie Manuale del proprietario

Marca: Logan

Modello: FRAMER'S EDGE PROFESSIONAL Serie

Tipo: Manuale del proprietario

FRAMER'S EDGE

MAT CUTTER MODELS 650, 655 & 660

www.logangraphic.com

Purchase Date

ID Number (on bottom of board)

Date (on bottom of board)

INSTRUCTION AND OPERATION MANUAL

Professional mat cutting system with laminate board

surface, production stops, 9" & 27" squaring arms, plus

dual straight and bevel cutting heads

PROFESSIONAL SERIES

For best results use only

authentic Logan blades

Logan Graphic Products, Inc.

1100 Brown Street

Wauconda, IL 60084

Phone (847) 526-5515 Fax (847) 526-5155

Toll Free (800) 331-6232

L618N3 6/05

Email - [email protected]

Model 650 Framer’s Edge - 40" mat cutter

Model 655 Framer’s Edge - 48" mat cutter

Model 660 Framer’s Edge - 60" mat cutter

Logan Graphic Products Inc., 1100 Brown Street, Wauconda, IL 60084 Toll Free 1 800 331 6232 www.logangraphic.com

FRAMER'S EDGE

MAT CUTTER MODELS 650, 655 & 660

The Logan Framer’s Edge Mat

Cutter has been designed

specifically with the framer in

mind. All the materials are heavy-

duty to withstand the rigors of

professional mat cutting and to

provide the accuracy framers

demand.

Features which Logan introduced

to the industry years ago like the

squaring arm, mat guide, the

movable production stop and the

high-tech aluminum cutting bar

have all been re-designed for

reduced fatigue, simple blade

change and precise adjustment of

the blade to maintain straight cuts

with no overcuts. In addition, the

cutting head contains a new

gauge which eliminates overcuts.

We are confident that the quality,

accuracy and dependability of the

Framer’s Edge will be everything

you expect in a professional mat

cutter.

This instructional manual is

written to acquaint you thoroughly

with this product. Referred to at

the outset, it will answer many

questions that may arise during

use. You will find that the time

taken will be well worth it and you

will be cutting top quality mats in

no time.

NOTE*

This instruction manual covers

the set-up and operation

instructions for the following

Framer’s Edge models:

#650 40” mat cutter

#655 48” mat cutter

#660 60” mat cutter

INTRODUCTION: TABLE OF CONTENTS:

Warranty

Logan Graphic Products, Inc. (“Logan”) warrants the 650/655/660 Framer’s Edge to be free from defects in parts and

workmanship for a period of two years from the date of original purchase. Logan warrants that it will either repair

or replace, in its sole discretion, any necessary replacement parts found to be defective. Should the product need to

be returned to Logan for repair or replacement parts, authorization for any return must come from Logan. Costs of

returning the product to Logan, including insurances, shall be borne by the purchaser. Logan shall not be liable for

any damages or losses, incidental or consequential, direct or indirect, arising from the use of this product. This

warranty extends only to the original purchaser and is not assignable or transferable. This warranty is in lieu of all

other warranties, expressed or implied.

Getting to know your Framer’s Edge Mat Cutter and identification of machine components

Set-up and Orientation

A. Unpacking 4

B. Work surface and orientation 4

C. Installing the mat guide channels 4

D. Attaching the squaring arms 4

E. Installing the mat guide 5

F. Blade installation-bevel cutter 5

G. Blade installation-straight cutter 5

H. Attaching the movable stop 6

I. Use a backing sheet 6

How to Cut a Mat

A. Straight cutting a mat board to size 7

B. Cutting a beveled opening using marked lines 8

C. Cutting a beveled opening using production stops 9

Adjustments & Maintenance

A. Blade depth adjustment-bevel cutter 10

B. Blade depth adjustment to cut 8-ply matboard 10

C. Blade tip adjustment 10

D. Overcut adjustment screws 11

E. Blade depth adjustment-straight cutter 11

F. Re-square the squaring arm 12

G. Re-parallel the mat guide 13

H. Bearing removal & replacement 13/14

Creative Matting Guide

A. Double Mat 15

B. Offset Corner Mat 15

C. Inlay Mat 15

Parts List and Exploded View Drawings

A. Cutting board 16

B. Cutting head 17

Trouble Shooting 18

Logan Graphic Products Inc., 1100 Brown Street, Wauconda, IL 60084 Toll Free 1 800 331 6232 www.logangraphic.com

FRAMER'S EDGE

MAT CUTTER MODELS 650, 655 & 660

1. Squaring Arm

Right angle back stop necessary to hold material square to Cutting Bar.

2. Cutting Bar

Heavy-duty extruded Cutting Bar with teflon coating and polished

surface.

3. Cutting Board

3/4” thick laminate surface Cutting Board.

4.Top Support Arm

Heavy-duty hinged aluminum arm provides support for Cutting Bar and

Handle Bar.

5. Handle Bar

Square shaped handle used to raise Cutting Bar to vertical position.

6. Bottom Production Stop

Production Stop tightens to the Cutting Bar Rod and stops the cutting

head at the location determined by the scale setting.

7. Bottom Support Arm

Heavy-duty hinged aluminum arm provides support for Cutting Bar and

Handle Bar.

8. Cutting Bar Scale

With dual inch/metric scale recessed into cutting bar to be used

together with the bottom production stop.

9. Squaring Arm Stop

Aluminum stop that slides onto either end of the Squaring A rm and

tightens into position.

10. Mat Guide

Movable, parallel guide bar used to set border width of the mat being

cut.

11. Cutting Head

Mounting block that glides on cutting bar and contains both bevel and

straight cutting blade holders.

12. Bevel Cutter Holder

45 Degree Bevel Blade Holder.

13. Straight Cut Blade Holder

90 Degree straight cut blade holder with lock-down pin.

14. Movable Production Stop

Movable stop which connects to cutting head. Allows fast production

cutting of mat board.

15. 8-Ply Setting

Adjustment screw used to set bevel cutting head to cut 8-ply thickness

matboard. Only the #268 blade will cut effectively at this setting.

16. Indicator Plate

Metal outrigger with green and red dot used to accurately start and

stop on marked lines resulting in minimal overcuts.

17. Blade Holding Screw

Easy grip blade screw for tightening blade on both straight and bevel

blade holders.

18. Bevel Cutter Blade Depth Adjustment

For adjusting the depth of the blade on the bevel side of the cutting

head.

19. Straight Cutter Blade Depth Adjustment

For adjusting the depth of the blade on the straight side of the cutting

head.

20. Lock-Down Pin

Pin for locking Straight Cutting Blade Holder in a down position so that

no downward pressure is needed when straight cutting.

21. Bottom Overcut Adjustment

For adjusting overcut at the bottom of the mat.

22.Top Overcut Adjustment

For adjusting overcut at the top of the mat.

23. Blades (Fig. 1, pg. 5)

#269 double bevel blade used for cutting standard thickness matboard.

#268 single bevel blade used for cutting 8-ply double thick matboard.

Logan Graphic Products Inc., 1100 Brown Street, Wauconda, IL 60084 Toll Free 1 800 331 6232 www.logangraphic.com

FRAMER'S EDGE

MAT CUTTER MODELS 650, 655 & 660

6. 7.

10.

11.

13.

17.

21.

19.

20.

22.

18.

IDENTIFICATION OF MACHINE COMPONENTS

Logan Graphic Products Inc., 1100 Brown Street, Wauconda, IL 60084 Toll Free 1 800 331 6232 www.logangraphic.com

FRAMER'S EDGE

MAT CUTTER MODELS 650, 655 & 660

SET-UP AND ORIENTATION

A. Unpacking

Remove the corrugated cardboard fillers and lift your Framer’s Edge Mat

Cutter out of the shipping box. SAVE THE BOX. Remove the parts bag and

check the contents: Fig 1

a. Squaring Arm Stop (1)

b. 27" Squaring Arm (1)

c. Production Stop (1)

d. Logan Screwdriver (1)

e. Five pack of Logan 269 blades (2)

f. Channel screws (4)

g. Mat guide channels (2)

h. Movable stop (1)

i. Mat Guide (1)

j. Five pack of Logan #268 blades (1)

k. 9" Squaring Arm (1)

B.Work Surface and Orientation

The work surface must be flat and smooth. Any dips or warps in a table top

can cause the base board of the mat cutter to also warp. Never lean the mat

cutter against a wall when not in use. Always store flat.The procedure

detailed in the following instructions refer to the right and left side and the

top and bottom of the mat cutter as shown. Fig 2

C. Installing Mat Guide Channels

Putting the rounded end in towards the center of the board press each Mat

Guide channel into the base board lining up the holes in the channels with

the holes in the board. Stand the base board up on its edge and insert the

four channel screws from the underside of the board and tighten. Fig 3

D. Attaching the Squaring Arm

There are two squaring arms provided to choose from. The 27" arm is used for

straight cutting. The 9" arm is an option if straight cutting is unnecessary or

saving space is required. The screws for attaching the Squaring Arm and the

small metal tool for aligning it can be found screwed into the board slot. Use

the alignment tool to line up the slot in the board with the slot in the

Squaring Arm before tightening the screws. Fig 4

#269

#268

Fig 1

Fig 4

Fig 3

Fig 2 Top

Right

Left

Bottom

Logan Graphic Products Inc., 1100 Brown Street, Wauconda, IL 60084 Toll Free 1 800 331 6232 www.logangraphic.com

FRAMER'S EDGE

MAT CUTTER MODELS 650, 655 & 660

F. Blade Installation-Bevel Cutter

There are two blades to choose from:

#268 is used for cutting 8-ply or double thick matboard.

#269 is used for cutting standard thickness matboard.

Using the handle bar, lift the cutting bar to the full upright position. Loosen blade

holding screw and insert blade into blade holder as far as it will go. Tighten the

blade holding screw.

To use #268 blade, refer to page 10 for instructions. Machine is preset to #269

blade setting.

NOTE: The hole in the blade is not designed to line up with the screw.

G. Blade Installation-Straight Cutter

With the handle bar in the down position, pull out on the lock down pin and rotate

the blade holder as far back as it will go. Loosen the blade holding screw and slide

one 269 blade into the blade holder as far back as it will go. Re-tighten the blade

holding screw. Rotate the blade holder back to the neutral position. Fig 7

E. Installing Mat Guide

To install the Mat Guide, loosen the knobs three full turns. Do not completelty

remove knobs. With the raised edge of the Mat Guide facing the Cutting Bar, align

the Mat Guide slides with the channels and drop the Mat Guide into place. Tighten

the knobs to set the Mat Guide at any increment. Fig 5

NOTE: If you experience any trouble dropping the Mat guide into the channels,

loosen the knobs one more additional turn and try again.

Fig 5

Fig 6

Fig 7

Logan Graphic Products Inc., 1100 Brown Street, Wauconda, IL 60084 Toll Free 1 800 331 6232 www.logangraphic.com

FRAMER'S EDGE

MAT CUTTER MODELS 650, 655 & 660

I. Use a Backing Sheet

For best results ALWAYS use a Backing Sheet when bevel cutting. A Backing Sheet is a

scrap piece of mat board which is at least as long as the mat you are cutting and at

least 4” wide. Your first Backing Sheet is included. The Backing Sheet will need to be

changed periodically. Helpful Hint: Move the Backing Sheet slightly after each cut to

avoid cutting into previous scores that may cause the blade to flare out causing a curve

in your cut. Fig 9

H. Attach the Movable Stop Arm

Slide the Movable Stop Arm onto scale bar with the leg toward board bottom and

tighten in position. Fig 8

Fig 8

Fig 9

FRAMER'S EDGE

MAT CUTTER MODELS 650, 655 & 660

Logan Graphic Products Inc., 1100 Brown Street, Wauconda, IL 60084 Toll Free 1 800 331 6232 www.logangraphic.com

A. Straight Cutting a Board to Size Using 27" Squaring Arm

1. Remove the mat guide, backing sheet, the squaring arm stop and the production

stop. Attach the squaring arm stop onto the far right end of the squaring arm and

slide inward until the left side of the stop is along the increment needed to

downsize your mat board to. Fig 1

2. Lift the cutting bar and slide the mat board along the squaring arm until it makes

contact with the squaring arm stop. Fig 2

3. Slide the cutting head past the far end of the mat board and rotate the straight

cut blade holder down until the lock down pin snaps over the top of the cutting

head locking the blade holder into cutting position. Fig 3

4. Holding the blade holder as shown in Fig 4, pull the cutting head directly

towards yourself until the mat board is completely cut.

5. IMPORTANT After finishing the cut make sure you pull the lock-down pin out to

allow the blade holder to go back to the neutral position. Fig 5

Helpful Hints:

1. After the lock down pin has locked the blade holder into cutting position, it is not

necessary to apply any downward pressure on the blade holder. The lock down

pin is holding the blade holder at the proper depth and extra pressure causes it

to cut deeper than needed.

2. Do not put any pressure down on the handle bar when cutting. This can cause

the cutting head to lift off of the mat board and not cut all the way through the

material.

NOTE: Your Framer’s Edge mat cutter has been pre-set to straight cut standard

thickness mat board. To cut thicker material you must make a blade depth

adjustment. See page 10 & 11.

Fig 1

Fig 2

Fig 3 Fig 4 Fig 5

Logan Graphic Products Inc., 1100 Brown Street, Wauconda, IL 60084 Toll Free 1 800 331 6232 www.logangraphic.com

FRAMER'S EDGE

MAT CUTTER MODELS 650, 655 & 660

Fig 1

B. Cutting a Beveled Opening Using Marked Lines

1. Always use a backing sheet when bevel cutting.

2. To release mat guide loosen the black knobs two turns. Slide the mat guide in

the angled slots until the front edge of the mat guide is along the increment of

the mat guide scale of the border width you wish to cut. Fig 1

3. Lift the handle bar and place a backing sheet on the cutting board. Then place

your pre-sized mat board color side down against the squaring arm and to the

left against the mat guide.

4. Lower the handle bar. With a pencil draw a line on the back of the mat board

using the left side of the cutting bar as a guide. Do this for the

remaining three sides of the mat. Fig 2

5. Slide the cutting head into position so that the edge of the metal near the

green dot on the indicator plate is directly over the marked line. Fig 3

6. Rotate the bevel blade holder down completely to seat the blade into the mat.

TIP: Hold the cutting head firmly enough to not allow it to “creep forward”

when first inserting the blade which will produce an overcut. Fig 4

Maintaining downward pressure, pull the cutting head towards yourself until

edge of the metal near the red dot on the indicator plate is directly over the

bottom marked line. Fig 5

7. Rotate the bevel blade holder up to the neutral position and lift the handle bar

to an upright position.

8. Turn the mat 1/4 turn to the right and make sure that the mat is down against

the squaring arm and against the mat guide on the left.

9. Continue steps 5 through 8 until all four sides are cut.

TIP: Do not push down on the handle bar when cutting, this will flex the

cutting bar upwards and prevent the blade from cutting through the mat

board.

Fig 2

Fig 3 Fig 4 Fig 5

Start on green dot. Stop on red dot.

Rotate blade holder.

FRAMER'S EDGE

MAT CUTTER MODELS 650, 655 & 660

Logan Graphic Products Inc., 1100 Brown Street, Wauconda, IL 60084 Toll Free 1 800 331 6232 www.logangraphic.com

C. Cutting a Beveled Opening Using Production Stops

1. Always use a backing sheet when bevel cutting.

2. To release mat guide loosen the black knobs two turns. Slide the mat guide in the angled

slots until the front edge of the mat guide is along the increment of the mat guide scale

of the border width you wish to cut. Fig 1

3. Lift the handle bar and place a backing sheet on the cutting board. Then place your pre-

sized mat board color side down against the squaring arm and to the left against the mat

guide and lower the handle bar.

4. Attach and slide the bottom production stop up to the increment on the scale of the

border size you wish to cut. Fig 2

5. Slide the top edge of the movable stop up to the increment on the scale of the border

size you wish to cut. Fig 3

6. Slide the cutting head into position in front of the top edge of the mat board. As the

movable stop approaches the edge of the mat board, press down on the stop foot with

your left index finger until it gently makes contact with the top edge of the mat. Fig 4

7. Holding the stop foot in place with your finger, rotate the blade holder down to enter the

blade into the mat. TIP: Hold the cutting head firmly enough to not allow it to “creep

forward” when first inserting the blade which will produce an overcut.

8. Release the stop foot with your finger so that it raises above the edge of the mat board

and pull the cutting head towards yourself until it makes gentle contact with the bottom

production stop. Fig 5

9. Turn the mat 1/4 turn to the right and make sure that the mat is down against the

squaring arm and against the mat guide on the left.

10. Continue steps 6 through 9 until all four sides are cut.

TIP: Do not push down on the handle bar when cutting, this will flex the cutting

bar upwards and prevent the blade from cutting through the mat board.

Fig 1

Fig 2

Fig 3

Fig 4

Fig 5

Logan Graphic Products Inc., 1100 Brown Street, Wauconda, IL 60084 Toll Free 1 800 331 6232 www.logangraphic.com

FRAMER'S EDGE

MAT CUTTER MODELS 650, 655 & 660

A. Blade Depth Adjustment - Bevel Cutter

NOTE: The depth setting of your Framer’s Edge is pre-set to cut U.S. Standard thickness

mat board. (.055” or 2.2mm)

To adjust the blade depth on the bevel cut, use the screwdriver provided and turn the

screwdriver in the slotted screw on the cutting head as shown. To decrease depth of the

bevel blade, turn the screw clockwise into the cutting head. To increase the depth of the

bevel blade, turn the screw counter-clockwise out of the cutting head. Fig 1

It is always ideal to have just enough blade depth to slice through the mat you are

cutting and score slightly into the backing sheet. Extra blade depth can allow the blade

to flex resulting in hooks or curves in the cut. Extra blade depth can also cause the

blade to start its cut sooner and stop its cut later than needed resulting in overcuts.

B. Blade Depth Adjustment to Cut 8-Ply Matboard

1. First remove the blade from the bevel blade holder.

2. Using the screwdriver supplied, tighten the small screw on the bevel blade holder

marked "8-ply setting".(Fig A)

3. Insert Logan 268 8-Ply Blade. Notice the blade has a bevel on only one edge. Be

careful to insert blade so bevel shows. Re-tighten the blade holding screw.

Note: #268 blade can only be used on one corner, bevel edge showing. It will not

operate properly installed with the opposite edge showing.

Fig 1

Fig A

Straight Depth

Adjustment Screw

Bevel Edge Depth

Adjustment Screw

C. Blade Tip Adjustment

If curves in your bevel cut become a problem, it may warrant an adjustment to the blade

tip. At the end of the bevel blade holder nearest the tip of the blade you will find a

small blade tip adjustment screw. When adjusted this screw will put more pressure

against the blade tip causing it to ride closer to the cutting bar. (Fig 2)

Do not turn this screw until you inspect the position of the blade tip in relation

to the edge of the cutting bar.

Ideally, the blade tip should just glide against the edge of the bar when activated. Raise

the handle bar and inspect this relationship by pivoting the blade holder down and

watching the blade tip as it passes by the edge of the cutting bar. If the blade tip is just

touching it, do not adjust the screw. If there is too much or too little contact between

the blade tip and the cutting bar then adjust the screw accordingly. Make only slight 1/4

turns on the screw and do test cuts to ensure accuracy.

Fig 2

FRAMER'S EDGE

MAT CUTTER MODELS 650, 655 & 660

Logan Graphic Products Inc., 1100 Brown Street, Wauconda, IL 60084 Toll Free 1 800 331 6232 www.logangraphic.com

E. Blade Depth Adjustment Straight Cutter

1. Micro Adjustment Screw

Located on top of cutting head, use screw driver provided to turn screw (Fig 1, page

10). By adjusting this screw you will effect the depth at which the straight cut

blade holder locks into when the lock down pin automatically engages. To decrease

depth of the straight blade, turn the screw clockwise into the cutting head. To

increase the depth of the straight blade, turn the screw counter-clockwise out of

the cutting head.

NOTE: Any depth beyond maximum setting will require you to use the depth setting

screws located on the straight cut blade holder.

2. 3/16" or 3/8" Depth Screws

Located on the side of the straight cut head, use screwdriver provided to turn

screw (Fig. 5). Remove blade and tighten desired screw. DO NOT OVER-TIGHTEN.

Replace blade and tighten knob.

Standard setting = both screws loosened.

3/16" setting = bottom 3/16" screw , 3/8" screw loose.

3/8" setting = bottom 3/8" screw , 3/16" screw loose.

Fig 5

Fig 3

D. Overcut Screw Adjustments

NOTE: These adjustments are only for when the production stops are being used.

1. Bottom Overcut Adjustment

If over or under cuts appears at the BOTTOM of the cut when using the production

stops even after a blade depth adjustment, use the Logan screwdriver provided to

make slight adjustments on the overcut adjustment screw on the back of the cutting

head. This screw will fine tune the BOTTOM over/under cut only when using the

production stop. Fig. 3

2.Top Overcut Adjustment

To adjust, loosen knob to allow leg to slide. Slide leg away from cutting head to

decrease overcut or toward cutting head to increase overcut.

Tighten knob to lock leg into position. Fig. 4

Fig 4

Logan Graphic Products Inc., 1100 Brown Street, Wauconda, IL 60084 Toll Free 1 800 331 6232 www.logangraphic.com

FRAMER'S EDGE

MAT CUTTER MODELS 650, 655 & 660

F. Re-Square the Squaring Arm

TOOLS NEEDED: Screwdriver, Carpenter’s Square.

ATTENTION: It is common for 32” x 40:” sheets of mat board to be un-square

when bought. Take this into account before making any adjustments to the

Squaring Arm.

Before making any adjustments to the squaring arm, make sure that the machine is truly

out of square, not the matboard, by using the squareness test.

SQUARENESS TEST

1. Place the carpenter’s square against the right hand side of the cutting bar and down

against the squaring arm. Look to see if there are any gaps between the carpenter’s

square and the squaring arm. If so, the squaring arm needs to be adjusted. Fig 6

TO RE-SQUARE

1. By looking at where the gap is, you can determine which way the squaring arm

needs to go in order to be square again.

2. Remove the squaring arm and locate the three screws inside of the slot.

3. Adjust only two screws A&B, DO NOT ADJUST C. To adjust you must turn screws A

& B in equal but opposite directions. To move the far right end of the squaring arm

towards the top end of the machine, turn adjustment screw B outward (counter-

clockwise) about a quarter turn and adjustment screw A inward (clockwise) a

quarter turn. Fig 7

4. Re-install the squaring arm and check for square. Make additional adjustments until

square.

Fig 6

Place square here

Fig 7

FRAMER'S EDGE

MAT CUTTER MODELS 650, 655 & 660

Logan Graphic Products Inc., 1100 Brown Street, Wauconda, IL 60084 Toll Free 1 800 331 6232 www.logangraphic.com

G. Re-Parallel The Mat Guide

TOOLS NEEDED: Phillips Screwdriver, Ruler.

To re-parallel the Mat Guide, first determine that the Mat Guide is out of parallel by

doing a parallel test.

Parallel Test:

1. Lock the Mat Guide at the 2” mark on the scale. Fig. 8

2. Place a scrap piece of matboard under the Cutting Bar and up against the Mat

Guide at the top end of the machine.

3. Using a pencil, draw a line across the matboard.

4. Slide the mat all the way down to the bottom where you are standing keeping the

mat against the mat guide but not against the Squaring Arm.

5. Draw another line across the matboard.

6. The piece of matboard should now appear to only have one single line across it. If

the two lines drawn do not line up with each other, the Mat Guide needs to be re-

paralleled.

To Re-parallel:

1. Release the Mat Guide screws.

2. Use a Phillips head screwdriver to loosen the screws on either side of the black

knobs one turn each. There are four screws total to be loosened this way.

3. Place a metal ruler or suitable straight edge between the Mat Guide and the

Cutting Bar. Fig. 9

4. Slide the Mat Guide against the straight edge and the Guide Rail. Make sure both

the Mat Guide and the Guide Rail are making solid contact on both sides of the

straight edge.

5. Re-tighten the Black Knobs first.

6. Then re-tighten the four screws. Do another parallel test to ensure that the Mat

Guide is now parallel.

H. Bearing Removal & Replacement

Additional Requirements: 600 Grit Silicon Carbide Paper (supplied)

If you have tried to eliminate all other causes of hooks and curves and they still exist,

check the cutting head for wobble on the cutting bar. If significant wobble occurs, it

may be time for a bearing replacement. Keep in mind that bearings last around three

years with regular use.

The Framer’s Edge cutting head is designed to ride on Delrin bearings installed

between the cutting head and cutting bar. The Delrin absorbs the wear so that costly

replacement and constant oiling of metal parts is not necessary. Logan provides these

bearings free for the lifetime of your machine. They will be sent to you free of charge

upon request. If you feel you cannot replace the bearing yourself, you can arrange for

our service department to do it.

NOTE: You must call to get a Return Authorization Number before sending your

machine in for bearing replacement.

For Service Assistance Phone 1-800-331-6232

Straight Edge

2”

Fig 8

Fig 9

Logan Graphic Products Inc., 1100 Brown Street, Wauconda, IL 60084 Toll Free 1 800 331 6232 www.logangraphic.com

FRAMER'S EDGE

MAT CUTTER MODELS 650, 655 & 660

Bearing Removal & Replacement

To Install New Bearings

If the Cutting Head has sufficient wobble and the cut is hooking, the Delrin

bearings need replacement.

To Remove Old Bearings:

1. Remove the blades.

2. Loosen screws A & B from bottom support arms. Fig 10

3. Slide Cutting Bar as far into the hole in the TOP support arm as possible

and lift it out and away from the BOTTOM support arm.

4. Slide Cutting Head off bar.

5. Use a screwdriver to remove four bearing screws and the indicator plate

screw. Fig 11

6. Remove old bearings and indicator plate.

To install new bearings:

New bearings are molded slightly oversize and require fitting to the existing

cutting bar.

1. Replace the new bearings. BE SURE THE “FLATS” MOLDED INTO THE

BEARINGS FACE TOWARD THE CENTER OF THE CUTTING HEAD. Fig 11

2. Now place a piece of 600 grit silicon carbide paper (supplied) on a flat,

even surface and gently sand away a small amount of the exposed

bearing surface.

3. After removing some of the bearing surface, try the Cutting Head on the

Cutting Bar. It should fit tightly.

NOTE: THIS IS A TRIAL AND ERROR METHOD OF BEARING REPLACEMENT.

DO NOT OVER-SAND THE BEARINGS.

4. At this point, check the relationship of the blade tip to the edge of the

Cutting Bar. If the blade hits the Cutting Bar before it reaches the end of

the bar, then more bearing surface has to be removed from the STRAIGHT

SIDE of the bearings. Fig 12 On the contrary, if the blade DOES NOT hit

the edge of the Cutting Bar, then more bearing surface must be removed

from the BEVEL SIDE of the bearings so that ultimately the blade will

JUST hit the edge of the bar as the blade enters the matboard.

Fig 10

Fig 11

Indicator Plate

Indicator

Plate Screw

Remove

Bearing

Screws

Remove

Bearing

Screws

Too Far Correct Too Close

Fig 12

FRAMER'S EDGE

MAT CUTTER MODELS 650, 655 & 660

Logan Graphic Products Inc., 1100 Brown Street, Wauconda, IL 60084 Toll Free 1 800 331 6232 www.logangraphic.com

DOUBLE RECTANGLE MAT

(Example: 8” x 10” with 31/2”x 5

1/2” opening)

Step 1 Set the Mat Guide to 2” and cut an opening in the mat from the BACK.

Step 2 Keeping the fallout piece in place, run double sided tape around the back

of the window border. Do not put tape on cut line. Also put a small

swatch of tape in the center of the fallout.

Step 3 Straight cut a second piece of matboard of desired color to an outside

dimension 71/2” x 91/2”.

Step 4 Affix the second mat FACE DOWN to the taped back of the first mat being

sure it is centered reasonably well.

Step 5 Set the Mat Guide to 21/4” and cut the second opening. The double fallout

will drop from the window and the mat will be finished and perfectly

aligned. NOTE: Triple mats can be achieved by repeating the above

procedures again.

OFF-SET CORNER MAT

(Example: 8” x 10” with 7” x 5” opening)

Step 1 Set the mat guide at 2” and draw all four lines.

Step 2 Reset the Mat Guide at 11/2” and draw another set of lines.

Step 3 Leaving the Mat Guide at 11/2”, place the mat in the cutter, put on the

Bevel Cutting Head and line up the silver indicator line with the bottom

pencil line closest to center of the mat. Cut until the silver indicator lines

up with he top pencil line closest to the center of the mat. Using the

same procedure, cut all four sides. IMPORTANT: At this point the

fallout will not drop from the window.

Step 4 Remove the mat and reset the Mat Guide to 2”. Reinsert the mat.

Step 5 Line up the silver indicator line on the Bevel Cutting Head with the drawn

pencil line furthest from the center of the mat. Cut until the silver indicator

line lines up with the line at the top of the mat furthest from the center of

the mat. Using the same procedure, cut all four sides. NOTE: Be careful to

hold the fallout piece in place as you turn the mat for the last cut.

Double Mat

Off-Set Corner Mat

Inlay Mat

INLAY MAT

(Example: 8” x 10” with 7” x 5” opening)

Step 1 Set the Mat Guide at 2” and cut as per regular instructions.

Step 2 Reset the Mat Guide at 11/2”. Keeping the fallout in place, cut the mat

again as per regular instructions. You may keep the fallout piece in place

by taping it on the back.

Step 3 Discard the outer border piece and fallout. Retain the inside border cutout.

Step 4 Leaving the Mat Guide in place at 11/2”, cut a second mat of a different

color as per regular procedures. IMPORTANT: The second mat must

be of the exact same outside dimension as the first mat.

Step 5 Remove the fallout piece from the second mat and place the inside border

cutout from the first mat in the window opening from the second mat.

The two pieces should fit together like a puzzle creating a flush surface

across the front of the mat. Put tape on back to hold it in place.

Detailed instructions on how to cut more creative style mats.

Logan Graphic Products Inc., 1100 Brown Street, Wauconda, IL 60084 Toll Free 1 800 331 6232 www.logangraphic.com

FRAMER'S EDGE

MAT CUTTER MODELS 650, 655 & 660

104-N cutting bar

106-7 squaring arm 27"

106-9 squaring arm 9"

107-2N1 squaring arm scale

109-N stop screw

112 mat guide knobs

112-F stop screw

113 support arm

116 shoulder bolt

118-N hinge block

120-N1 cutting bar stop

124-N board foot

134 squaring arm stop

135 handle bar

153-2 mat guide

203-N screw

211 handle bar screw

216 set screw

221 end cap

222 bumper

602-N mat guide slide

603-N mat guide wedge

604 mat guide screw

608-N1 cutting board

610-M mat guide scale

616 squaring arm screw

730-N cutting bar scale

1004 mat guide channel

1025-N mat guide channel screws

PART # DESCRIPTION PART # DESCRIPTION PART # DESCRIPTION

104-N

106-7

730-N

113

116 216

118-N

116

120-N1

134 112-F

602-N

603-N

112

1025-N

604

153-2

1004

211

124-N

135

221

610-M

107-2N1

109-N

113

see page 17 for

cutting head

schematic

222

203-N

608-N1

616

PARTS LIST - Base Board

Logan Graphic Products Inc., 1100 Brown Street, Wauconda, IL 60084 Toll Free 1 800 331 6232 www.logangraphic.com

FRAMER'S EDGE

MAT CUTTER MODELS 650, 655 & 660

PART # DESCRIPTION PART # DESCRIPTION

PART # DESCRIPTION

PARTS LIST - Cutting Head

L101-650 cutting head base 1

L102-A bevel blade holder 1

L102-B straight blade holder 1

L103-A bevel blade cover 1

L103-B straight blade cover 1

L108 shim 1

L111-N scale bar 1

L114-A2 shoulder screw 2

L115 Delrin bearing 2

L117-N movable stop arm 1

L139 gauge screw 1

L143-N indicator gauge 1

L146-N movable stop leg 1

L147-N lock-down pin 1

L202/204 post 1

L206-N blade tip screw 2

L207-N bearing screw 4

L208-N cover screw 1

L112-F stop screw 1

L220-N blade screw 2

L241-N scale bar screw 1

L242 e-ring 1

L273 blade cover screw 2

L430-A straight cut blade depth screw 3

L613 bevel return spring 1

L614 straight return spring 1

L730-N movable stop scale 1

L865-N bevel blade depth screw 1

L254-N overcut set screw 1

L101-650 N

L220-N

L1273

L208-N

L147-N

L220-N

L865-N

L112-F

L444-250

L146-N

730-N

L241-N

L430-A

L111-N

L117-N

L206-N

L273

L206-N

L273

L114-A2

L108

L102-B

L614

L202/204

L103-A

L114-A2

L108

L102-A

L613

L143-N

L207-N

L115

L207-N

L242

L103-B

L139

L254-N

Logan Graphic Products Inc., 1100 Brown Street, Wauconda, IL 60084 Toll Free 1 800 331 6232 www.logangraphic.com

FRAMER'S EDGE

MAT CUTTER MODELS 650, 655 & 660

Problem

Ragged bevel cuts

Over-Cut at the start of the

cut

Over-Cut at the end of the

cut

Cutting through at ends of

mat but not in middle

TROUBLE SHOOTING

Possible Reasons

■Cutting without a backing sheet.

■Backing sheet is worn out.

■Dull or chipped blades.

■Cutting head crawling forward as you

insert the blade.

■Production stop set incorrectly.

■Blade depth set too deep.

■Production stop set incorrectly.

■Adjustment needed to overcut

adjustment screw.

■Pushing down on handle bar while

cutting.

■Backing sheet not proper length.

■Machine not on level surface.

■Inconsistent pressure being applied to

blade holder during cut.

Hook in the corner of the

bevel cut

Curve in the bevel cut

Cutting head hard to pull

when cutting

■Blade depth set too deep.

■Cutting without a backing sheet.

■Backing sheet is worn out.

■Pushing down on handle bar while

cutting.

■Blade depth set too deep.

■Cutting without a backing sheet.

■Backing sheet is worn out.

■Pushing down on handle bar while

cutting.

■Worn bearings.

■Machine not on level surface.

■Blade depth set too deep.

■Did not remove backing sheet while

straight cutting.

■Not pulling from center of the cutting

head.

■Blade is dull.

More great Logan products…

#708 Extension Table

Laminate surface board

extension that mounts on

to #650, #655 or #660

mat cutters. Allows

border sizes up to 17”

using parallel mat guide.

Logan Surface V-Groover Offers a way to cut surface

V-Grooves quickly and accurately with zero overcuts.

Push-Pull action cuts V-Grooves right on the surface

of the matboard eliminating any need for trimming or

taping. Works entirely with stops.

Logan V-Groover - Model #705

Replacement Blades - Model #1258

Freestyle Cutter - Model 1100

Push or pull style cutter with ergonomic shape and

fixed blade. Great for freestyle mat cutting. Use right

or left handed. Available in two colors: Red and

Silver. Three extra blades included.

Foamboard Cutter -

Model 1500

Push style fixed blade

cutter can be used against

any suitable straight edge.

Reversible, it cuts 90° or

45° bevel with an

adjustable blade to a

foamboard thickness of

1/8” (3mm), 3/16” (5mm)

and 3/8” (10mm). Includes

three extra blades.

3-Step Oval and Circle Mat Cutter is easy to use, fast

and portable. Cuts ovals or circles on the surface of

the matboard using a patented 3-step mechanism for

gradual increase of blade depth.

Converts from oval to circle cutter with a turn of a

knob. Ovals from 3 1/4” x 4 3/4” to 20” x 23”. Circles

from 4 1/2” to 20”.

Uses common blade. Logan - Model 324, Dexter or X-

Acto equivalent.

3-Step Oval & Circle Mat Cutter - Model 201.

Replacement blades - Model 324.

Problem Possible Reasons

Logan Graphic Products Inc., 1100 Brown Street, Wauconda, IL 60084 Toll Free 1 800 331 6232 www.logangraphic.com

FRAMER'S EDGE

MAT CUTTER MODELS 650, 655 & 660

For more creative ideas in matting,

pick up a copy of Logan’s

“How To Cut Mats” Video by

Vivian C. Kistler, CPF. - Model 237.

Add personality to your mats

with the Logan Mat

Decoration Kit - Model 526

Includes decorative supplies &

instructions.

Complete and detailed directions featuring

Logan's picture framing tools system.

Learn inside secrets from professional

framers for creating your own custom

framed art.

Home Picture Framing - Model F245

Also available are 3 different books on matting and

framing by Vivian C. Kistler, CPF.

Basic Mat Cutting - Model 238-M.

Mat Decoration Book- Model 240-M.

Do It Yourself Picture Framing- Model 241-M.

See your local Logan Dealer for availability. Call at 800/331-6232 for

a dealer near you, or please check our 'where to buy' section on

Logan's website www.logangraphic.com

Also available from Logan…

La pagina si sta caricando...

Logan FRAMER'S EDGE PROFESSIONAL Serie Manuale del proprietario

Marca: Logan

Modello: FRAMER'S EDGE PROFESSIONAL Serie

Tipo: Manuale del proprietario

Scarica PDF

rapporto

in altre lingue

English: Logan FRAMER'S EDGE PROFESSIONAL Serie Owner's manual
français: Logan FRAMER'S EDGE PROFESSIONAL Serie Le manuel du propriétaire
español: Logan FRAMER'S EDGE PROFESSIONAL Serie El manual del propietario
português: Logan FRAMER'S EDGE PROFESSIONAL Serie Manual do proprietário

Logan FRAMER'S EDGE PROFESSIONAL Serie Manuale del proprietario

Logan FRAMER'S EDGE PROFESSIONAL Serie Manuale del proprietario

in altre lingue

Documenti correlati

Altri documenti