SGM IDEA SPOT 250 Manuale utente

USER’S MANUAL REL. 1.01

SGM TECHNOLOGY FOR LIGHTING SPA

VIA PIO LA TORRE, 1 _ 61010 TAVULLIA (PU), ITALY

TEL. +39 0721 476477 _ FAX +39 0721 476170

www.sgm.it _ [email protected]

GB

I

D

F

E

P

WIT070

MOVING HEADS

IDEA SPOT 250

Vi ringraziamo per aver acquistato un prodotto SGM.

Per ottenere i migliori risultati dal suo utilizzo, vi preghiamo di leggere attentamente questo manuale di istruzioni.

Al suo interno troverete le informazioni tecniche e le specifiche d’uso del prodotto. Nelle pagine in appendice tro-

verete inoltre schemi e diagrammi destinati all’assistenza tecnica.

Nell’ottica di qualità SGM, è possibile che l’Azienda apporti migliorie ai suoi prodotti, per cui consigliamo di alle-

gare il manuale al prodotto stesso e di trascrivere il numero di serie nell’ultima pagina della copertina: utilizzando

il presente manuale con un apparecchio fabbricato prima o dopo la sua stampa, potrebbero esserci discrepanze

fra l’apparecchio e quanto riportato nel manuale stesso.

Thank you for buying an SGM product.

To obtain the best results, please carefully read this instruction manual in which you will find technical information

and specifications for use of the product, as well as diagrams for technical service in the appendix.

In light of SGM quality, the company may make improvements to its products. Therefore, we recommend that the

manual be attached to the product and the serial number copied onto the back cover: using this manual with

equipment manufactured before or after its printing, might show discrepancies between the equipment and the

information listed in the manual.

Wir danken Ihnen für den Kauf eines Produkts von SGM.

Zur Erzielung der besten Resultate bei der Benutzung bitten wir Sie, die vorliegende Bedienungsanleitung aufmerk-

sam zu lesen. Darin finden Sie die technischen Informationen sowie die Anweisungen für die Benutzung des

Produkts. Im Anhang befinden sich auBerdem die Schaltpläne undv Diagramme für den Kundendienst.

SGM behält sich das Recht vor, Verbesserungen an den Produkten vorzunehmen und deshalb empfehlen wir, die

Bedienungsanleitung dem Produkt stets beizulegen und die Seriennummer auf der letzten Seite des Umschlags

einzutragen. Bei der Verwendung dieses Handbuches mit einem Gerät, das vor oder nach der Drucklegung produ-

ziert wurde, können sich Abweichungen zwischen Gerät und dem Inhalt des Handbuches ergeben.

Nous vous remercions d’avoir acheté un produit SGM.

Pour optimiser son utilisation, nous vous prions de bien vouloir lire attentivement cette notice où vous trouverez

les informations techniques et les caractéristiques d’utilisation du produit. En outre, vous trouverez également,

dans les pages en appendice, les schémas et les diagrammes concernant l’assistance technique.

Le concept de qualité SGM, lui permet d’améliorer continuellement ses produits et c’est pourquoi nous vous con-

seillons de joindre la notice au produit et d’inscrire le numéro de sèrie sur la page de couverture. En effet, si on

l’utilise avec un appareil fabriqué avant ou après son impression, il peut y avoir des différences entre l’appareil et

ce qui figure dans la notice.

Les estamos sumamente agradecidos por haber elegido un producto SGM.

Para obtener los mejores resultados, les rogamos leer detenidamente el presente manual de instrucciones. El

mismo contiene las informaciones técnicas y las indicaciones de uso del producto. Las páginas anexas contienen

además los esquemas y diagramas necesarios para la asistencia técnica.

Para mantener la calidad SGM, es posible que la Empresa aporte mejoras sus productos, por ello les aconsejamos

conservar el manual junto con el aparato correspondiente y escribir su número de serie en la última página del

manual; si en cambio se utiliza el presente manual con un aparato frabicado antes o después de su impresión, es

probable que existan discrepancias entre el aparato y las indicaciones del mismo.

GB SGM Technology for Lighting

Idea Spot 250 WIT070 V1.0-01NR

1

Table of Contents

INTRODUCTION:.............................................................................................................. 2

Features ..................................................................................................................................... 2

SAFETY INSTRUCTIONS .................................................................................................... 3

GENERAL GUIDELINES ..................................................................................................... 4

INSTALLATION INSTRUCTIONS .......................................................................................... 4

a) Installing or replacing the lamp ................................................................................................. 4

b) Mounting the device................................................................................................................. 6

Installation method via clamp ....................................................................................................... 7

DMX-512 control connection.......................................................................................................... 8

Control Board.............................................................................................................................. 9

Main functions........................................................................................................................... 11

INSTRUCTIONS ON USE: ................................................................................................ 19

ERROR CODES: ............................................................................................................. 22

CLEANING AND MAINTENANCE........................................................................................ 23

TECHNICAL SPECIFICATIONS .......................................................................................... 23

SGM Technology for Lighting GB

WIT070 V1.0-01NR Idea Spot 250

2

KEEP THIS MANUAL FOR FUTURE NEEDS

For your own safety, please read this user manual carefully before installing the device.

CAUTION !

Keep this device away from rain and moisture!

Unplug mains lead before opening the housing

EVERY PERSON INVOLVED WITH THE INSTALLATION, OPERATION AND MAINTENANCE OF THIS DEVICE

HAS TO:

- BE QUALIFIED,

- FOLLOW CAREFULLY THE INSTRUCTIONS OF THIS MANUAL.

INTRODUCTION:

Thank you for having chosen this professional moving head.

You will see you have acquired a powerful and versatile device.

Unpack the device. Inside the box you should find:



the fixture device,



a power cable,



an XLR connection cable,



a pair of Quick-lock omega holders,



a safety cable,



this manual.

Please check carefully that there is no damage caused by transportation. Should there be any, consult your

dealer and don’t install this device.

Features

 Lamp: Philips MSD250/2

 Control signal : standard DMX-512, 14 channels (16 bit) or 12 channels ( 8 bit)

 Stand alone operation with Master/Slave function, sound activated via built in microphone.

 Pan and tilt movement :

- 8 bit and 16 bit resolution for smooth and precise motion

- pan : 630° (optional : 540°) rotation , tilt : 265° rotation

- speed of pan/tilt movement adjustable

- scan position memory, auto reposition after unexpected movement

 Focus: electronic focus

 Strobe/shutter : high speed dual-blade shutter, 0-13Hz or random strobe

 Dimmer : mechanical adjust 0%~100%

 Colours:1 color wheel with 8 dichroic mirrors plus white, rainbow effect

 Gobos: 2 gobo wheels

 Rotation gobo wheel: 6 rotating gobos plus open, rotating speed adjustable, and gobo indexing

 Fix gobo wheel: 7 fix gobos plus open, both 2 gobo wheels have different speed gobo shake and rainbow effect

 Prism: 3- face speed adjustable prism rotates in two directions with 16 prism macro effect

 Auto-program: 8 pre-built programs can be selected

 Display: Can be changed 180° reverse to fit for different installation position.

 Local and remote reset and lamp on/off.

 Editable program: Edit and save the program to inside EEPROM via the control board or external controller,

up to 48 scenes can be saved and then can be run in Stand Alone or sound activated.

GB SGM Technology for Lighting

Idea Spot 250 WIT070 V1.0-01NR

3

SAFETY INSTRUCTIONS

CAUTION

Be careful with your operations. With a dangerous voltage you can Suffer

a dangerous electric shock when touching wires!

This device has left the factory in perfect condition. In order to maintain this condition and to ensure a safe

operation, it is absolutely necessary for the user to follow the safety instructions and warning notes written

in this user manual.

IMPORTANT

Damages caused by the disgregard of this user manual are not subject to warrenty.

The dealer will not accept liability for any resulting defects or problems.

If the device has been exposed to temperature changes due to environmental changes, do not switch it on

immediately. The arising condensation could damage the device. Leave the device switched off until it has

reached room temperature.

This device falls under protection-class I. Therefore it is essential that the device be earthed.

The electric connection must carry out by qualified person.

The device shall only be used with rate voltage and frequency.

Make sure that the available voltage is not higher than stated at the end of this manual.

Make sure the power cord is never crimped or damaged by sharp edges. If this would be the case,

replacement of the cable must be done by an authorized dealer.

Always disconnect from the mains, when the device is not in use or before cleaning it. Only handle the

power cord by the plug. Never pull out the plug by tugging the power cord.

During initial start-up some smoke or smell may arise. This is a normal process and does not necessarily

mean that the device is defective, it should decrease gradually.

CAUTION

Never touch device during operation!

The housing may heat up.

Never look directly into the light source,

as sensitive persons may suffer an epileptic shock.

Please be aware that damages caused by manual modifications to the device are not subject to warranty.

Keep away from children and non-professionals.

SGM Technology for Lighting GB

WIT070 V1.0-01NR Idea Spot 250

4

GENERAL GUIDELINES

This device is a lighting effect for professional use on stages, in discotheques, theatres, etc.

This fixture is only allowed to be operated with the max alternating current which stated in the technical

specifications in the last page of this manual, the device was designed for indoor use only.

Lighting effects are not designed for permanent operation. Consistent operation breaks may ensure that

the device will serve you for a long time without defects. Do not shake the device.

Avoid brute force when installing or operating the device.

The device shall only be used complete with its protective shield.

While choosing the installation-spot, please make sure that the device is not exposed to extreme heat,

moisture or dust. The minimum distance between light-output from the projector and the illuminated

surface must be more than 0,5 meter.

Always fix the fixture with an appropriate safety cable if you use the quick lock cam in hanging up the

fixture, please make sure the 4 quick lock fasteners turned in the quick lock holes correctly.

Operate the device only after having familiarized with its functions. Do not permit operation by persons not

qualified for operating the device. Most damages are the result of unprofessional operation.

Please use the original packaging if the device is to be transported.

For safety reasons, please be aware that all modifications on the device are forbidden.

If this device will be operated in any way different to the one described in this manual, the product may

suffer damages and the guarantee becomes void. Furthermore, any other operation may lead to

short-circuit, burns, electric shock, lamp explosion, crash, etc.

INSTALLATION INSTRUCTIONS

a) Installing or replacing the lamp

CAUTION

Only install the lamp with the device unplugged from the

mains

.

The lamp has to be replaced when it is damaged or deformed.

Before replacing the lamp let the lamp cool down, because during operation, the lamp can

reach very high temperature.

During the installation of the lamps do not touch the glass bulbs bare handed. Always use a cloth to handle

the lamps during insertion and removal.

Do not install lamps with a higher wattage. They generate higher temperatures than which the device was

designed for.

GB SGM Technology for Lighting

Idea Spot 250 WIT070 V1.0-01NR

5

For the installation, you need one Philips MSD 250/2:

Procedures:

1 2

3

4

1

.

Unscrew the 2 screws (A, B) on the bottom of the housing, holding the plate where the lamp is

underneath.

2

.

Gently pull the socket holder using the knob in the middle.

3

.

Carefully insert the lamp into the socket. Please remember there is only one way to insert the lamp.

Gently slide the lamp and its lamp holder back into place and fasten the 2 screws.

4

.

On the access plate there are 3 small screws marked 1,2 and 3.which are used to adjust the lamp

holder in the lamp housing. You can adjust the 3 screws to fine-turn the position of the lamp to get the

maximum light output as shown below.

A

B

Please remember the lamp is not a hot-restrike type, you must wait for approximately 10 minutes after

having turned off the lamp before you can turn it back on again.

CAUTION

Do not operate this device with open cover

SGM Technology for Lighting GB

WIT070 V1.0-01NR Idea Spot 250

6

b) Mounting the device

CAUTION

Pleas consider the EN 60598-2-17 and the other respective

national norms during the installation. The installation must

only be carried out by a qualified person.

The installation of the effect has to be built and constructed in a way that it can hold 10 times the weight

for 1 hour without any harming deformation.

The installation must always be secured with a secondary safety attachment, e.g. an appropriate safety

cable.

Never stand directly below the device when mounting, removing or servicing the fixture.

The operator has to make sure the safety relating and machine technical installations are approved by an

expert before taking the device into operation for the first time.

These installations have to be approved by a skilled person once a year.

CAUTION

Before taking into operation for the first time, the

installation has to be approved by an expert.

Cautions:

The effect should be installed outside areas where persons may reach it, walk by or be seated.

CAUTION

When installing the device, make sure there in no highly

inflamm able material within a distance of min. 0,5m

Overhead mounting requires extensive experience, including amongst others calculating

working load limits, installation material being used, and periodic safety inspection of all

installation material and the device. If you lack these qualifications, do not attempt the

installation yourself. Improper installation can result in bodily injury.

CAUTION

The electric connection must only be carried out by a

qualified electrician.

Before mounting make sure that the installation area can hold a minimum point load of 10 times the

device’s weight.

Connect the fixture to the mains with the power plug.

GB SGM Technology for Lighting

Idea Spot 250 WIT070 V1.0-01NR

7

Installation method via clamp

Please refer to the picture below:

Screw one clamp each via a M12 screw and nut onto the Omega holders.

Insert the quick-lock fasteners of the first Omega holder into the respective holes on the bottom of the

device. Tighten the quick-lock fasteners fully clockwise. Install the second Omega holder.

Pull the safety-rope through the holes on the bottom of the base and over the trussing system or a safe

fixation spot. Insert the end in the carabine and tighten the safety screw.

SGM Technology for Lighting GB

WIT070 V1.0-01NR Idea Spot 250

8

DMX-512 control connection

The product has a DMX 512 input fitted with standard 5-pin XLR connectors. Screened cables in

compliance with EIA RS-485 specifications and the following characteristics must be used for connections:

- 2 conductors plus screen

- 120 Ohm impedance

- low capacitance

- max. transmission rate 250kBaud.

Cable connections:

see illustration, taking care with the screen, which must be connected to

Pin 1

DMX-512 connection with DMX terminator

For installations where the DMX cable has to run a long distance or is in an electrically noisy environment,

such as in a discotheque, it is recommended to use a DMX terminator. This helps in preventing corruption

of the digital control signal by electrical noise. The DMX terminator is simply an XLR plug with a 120 Ω

resistor connected between pins 2 and 3,which is then plugged into the output XLR socket of the last

fixture in the chain. Please see illustrations below.

CONTROLLER

Projector 3

Starting address 29

Projector 2

Starting address 15

Projector 1

Starting address 1

GB SGM Technology for Lighting

Idea Spot 250 WIT070 V1.0-01NR

9

Projector DMX starting address selection

All fixtures should be given a DMX starting address when using a DMX signal, so that the correct fixture

responds to the correct control signals. This digital starting address is the channel number from which the

fixture starts to ‘’listen’’ to the digital control information sent out from the DMX controller. The allocation

of this starting address is achieved by setting the correct number on the display located on the base of the

device.

You can set the same starting address for all fixtures or a group of fixtures , or make different address for

each fixture individually.

If you set the same address, all the units will start to ‘’listen’’ to the same control signal from the same

channel number. In other words, changing the settings of one channel will affect all the fixtures

simultaneously.

If you set a different address, each unit will start to ‘’listen’’ to the channel number you have set, based on

the quantity of control channels of the unit. That means changing the settings of one channel will affect

only the selected fixture.

In the case of the product, which is a 14 channel fixture, you should set the starting address of the first unit

to 1, the second unit to 15 (14 + 1), the third to 29 (15 + 14), and so on.

Note:

The modes of DMX 512 data and lamp are shown via the display:

.

Lamp on

DMX OK

NO DMX

Lamp off

1. After switching on, the device will automatically detect whether DMX 512 data is received or not. If the

data is received, the display will show "A.001" with the actually set address. If there is no data received

at the DMX-input, the display will flash "A001" with the actually set address.

This situation can occur if:

- the 5 PIN XLR plug (cable with DMX signal from controller) is not connected with the input of the device.

- the controller is switched off or defective, if the cable or connector is defective or the signal wires are

swap in the input connector.

It’s necessary to insert the XLR termination plug (with 120 Ohm) in the last lighting in the link in order to

ensure proper transmission on the DMX data link.

2. If the lamp is on, the display will show "A00.1" with the actually set address. If the lamp is off, the

display will show "A001" with the actually set address.

Control Board

The Control Board offers several features: you can simply set the starting address, switch on and off the

lamp, run the pre-programmed program or make a reset.

The main menu is accessed by pressing the Mode/esc-button until the display starts flashing. Browse

through the menu by pressing the Up-button or Down-button. Press the Enter-button in order to select

the desired menu. You can change the selection by pressing the Up-button or Down-button. Confirm

every selection by pressing the Enter-button. You can leave every mode by pressing the

Mode/esc-button . The functions provided are described in the following sections.

SGM Technology for Lighting GB

WIT070 V1.0-01NR Idea Spot 250

10

Default settings shaded.

Note:

By default setting, the lamp is not ignited with power on. Lamp can be turned on via DMX controller.

Main

menu

Sub.

menu

Extension Display Function

VALU A001~AXXX (AXXX) DMX address setting

SLAV ON/OFF (SLAV) Slave setting

ADDR

EBOC ON/OFF

Change DMX address via

external controller

ALON (AU-A) Automatic Run in Stand Alone

AUTO

MAST (AU-M) Automatic Run as Master

ALON (SO-A)

Sound-controlled Run in Stand

Alone

RUN

SOUN

MAST (SO-M)

Sound-controlled Run as

Master

VALU D–XX D-00 (DXXX)

Display the DMX 512 value of

each channel

RDIS ON/OFF Reverse display

0

MODE

DISP

CLDI ON/OFF Shut off LED display

OPEN ON/OFF Lamp on/off

LAAU ON/OFF

Lamp automated on with

power

ONLI ON/OFF Lamp on/off via controller

1

LAMP

DELA D–XX D-05 Delay lamp on

RPAN ON/OFF Pan Reverse

RTIL ON/OFF Tilt Reverse

16BI ON/OFF Switch 16 bit/8 bit

DEGR 630/540 Pan degree select

DIMM Slow/Fast Dimmer speed

MIC M-XX Mic sensitivity

AUTO Clos/Hold/Auto/Audi No DMX Status

FANS HIGH/AUTO Fan’s mode select

SPEE SP-1/SP-2 Movement Mode Select

REST Reset

LODA ON/OFF Restore factory settings

2

SET

VER V-1.0~V-9.9 Software version

LADJ ON/OFF Lamp adjustment

TEST T–01~T–30 Test function of each channel

CODE CXXX Fixture code *code is “C050”

3

ADJU

WHEL

CH01~CH30 XXXX(-128~127) Motor Calibration

MATI 0000~9999(hours) Fixture running time

LATI 0000~9999(hours) Lamp running time

CLMT ON/OFF Clear fixture time

4

TIME

CLLT ON/OFF Clear lamp time

STEP S–01 ~S–48 Steps of Program Run

REC. RE.XX Auto Save Scene

C–01~C–30

0 1 XX(00~FFH)

3 0 XX(00~FFH)

Edit the channels of each

scene

TIME T XXX(001~999) Time for each scene

5

EDIT

SC01

~ SC48

CNIN ON/OFF Edit program via controller

GB SGM Technology for Lighting

Idea Spot 250 WIT070 V1.0-01NR

11

Main functions

- Main menu 0

1. Press [MODE/ESC] to enter the main menu "MODE" (display flashing)

2. Press [ENTER] and select "ADDR",’’RUN’’ or "DISP" by pressing [UP] or [DOWN] button.

3. Press [ENTER] for selecting the desired sub menu.

- DMX address setting, Slave setting

- DMX address setting

With this function, you can adjust the desired DMX-address via the Control Board.

1. Select ‘’VALU’’ by pressing [UP] or [DOWN] button.

2. Press [ENTER], the display shows “AXXX” ,“XXX” stands for the DMX address from 001 to 511.

3. Adjust the DMX address by pressing [UP] or [DOWN] button.

4. Press [ENTER] to confirm or pressing [MODE/ESC] to return to main menu.

- Slave setting

With this function, you can define the device as slave.

1. Select ‘’SLAV’’ by pressing [UP] or [DOWN] button.

2. Press [ENTER], the display shows ‘’ON’’ or ‘’OFF’’.

3. Press [UP] to select ‘’ON’’ if you wish to enable this function or press [DOWN] to select ‘’OFF’’ if you

don’t.

4. Press [ENTER] to confirm or press [MODE/ESC] to return to main menu.

-DMX address setting via controller

With this function, you can adjust the desired DMX-address via an external controller.

This function can only be activated when the DMX-value of all other channels is set to "0" on the

controller.

 Select “EBOC” by pressing [UP] or [DOWN].

 Press [ENTER], the display shows “ON” or “OFF”.

 Press [UP] to select “ON” if you wish to enable this function or [DOWN] to select “OFF” if you don’t.

 Press [MODE/ESC] to confirm.

 Press [ENTER] in order to return to the main menu.

 On the controller, set the DMX-value of channel 1 to "7".

 Set the DMX-value of channel 2 to "7"or "8". When set to "7" you can adjust the starting address

between 1 and 255. When set to "8" you can adjust the starting address between 256 and 511.

 Set the DMX-value of channel 3 to the desired starting address. If you want to set the starting address

to 57, set channel 1 to "7", channel 2 to "7" and channel 3 to "57". If you want to set the starting

address to 420, set channel 1 to "7", channel 2 to "8" and channel 3 to "164" (256+164=420).

 Wait for approx. 20 seconds and the unit will carry out a reset. After that, the new starting address is

set.

SGM Technology for Lighting GB

WIT070 V1.0-01NR Idea Spot 250

12

- Program Run, Master setting

With the function "RUN", you can run the internal program. You can set the number of steps under Step.

You can edit the individual scenes under Edit. You can run the individual scenes either automatically

(AUTO), i.e. with the adjusted Step-Time or sound-controlled (SOUN). The selection "ALON" means Stand

Alone-mode and "MAST" that the device is defined as master.

1. Select "AUTO" or "SOUN" by pressing [UP] or [DOWN] button.

2. Press [ENTER] for selecting the desired extension menu.

3. Select "ALON" or "MAST" by pressing [UP] or [DOWN] button.

4. Press [ENTER] to confirm or Press [MODE/ESC] to return to the main menu.

- Display the DMX-value, Reverse display, Shut off LED display

- Display the DMX 512 value of each channel

With this function you can display the DMX 512 value of each channel.

1. Select "VALU" by pressing [UP] or [DOWN] button.

2. Press [ENTER] to confirm; the display shows “D-00”. In this setting, the DMX-adjustment of every

channel will be displayed.

3. The display shows "D-XX, “XX” stands for the DMX-value of the selected channel, press [UP] or

[DOWN] button in order to select the desired channel. If you select “D-14” the display will only show

the DMX-value of the 14th channel.

4. Press [ENTER] to confirm or Press [MODE/ESC] to return to the main menu.

- Reverse display

With this function you can rotate the display by 180°.

1. Select "RDIS" by pressing [UP] or [DOWN] button.

2. Press [ENTER], the display shows ‘’ON’’ or ‘’OFF’’.

3. Press [UP] to select ‘’ON’’ if you wish to enable this function,or press [DOWN] button to ‘’OFF’’ if

you don’t; the display will rotate by 180

o

.

4. Press [ENTER] to confirm or Press [MODE/ESC] to return to the main menu.

- Shut off LED display

With this function you can shut off the LED display after 2 minutes.

1. Select "CLDI" by pressing [UP] or [DOWN] button.

2. Press [ENTER], the display shows ‘’ON’’ or ‘’OFF’’.

3. Press [UP] to select ‘’ON’’ if you wish to enable this function or press [DOWN] button to ‘’OFF’’ if you

don’t.

4. Press [ENTER] to confirm or Press [MODE/ESC] to return to the main menu.

GB SGM Technology for Lighting

Idea Spot 250 WIT070 V1.0-01NR

13

- Main menu 1

1. Press [MODE/ESC] to enter the main menu (display flashing).

2. Press [UP] or [DOWN] button to select ‘’LAMP’’.

- Lamp on/off

With this function you can switch the lamp on or off via the Control Board.

1. Select ‘’OPEN’’ by pressing [UP] or [DOWN] button.

2. Press [ENTER], the display shows ‘’ON’’ or ‘’OFF’’.

3. Press [UP] to select ‘’ON’’ if you wish to enable this function or press [DOWN] button to ‘’OFF’’ if you

don’t.

4. Press [ENTER] to confirm or Press [MODE/ESC] to return to the main menu.

- Lamp automated on with power.

With this function you can set the lamp be ignited or not when the fixture is power on.

1. Select ‘’LAAU’’ by pressing [UP] or [DOWN] button.

2. Press [ENTER], the display shows ‘’ON’’ or ‘’OFF’’.

3. Press [UP] to select ‘’ON’’ if you wish to enable this function or press [DOWN] button to ‘’OFF’’ if

you don’t.

4. Press [ENTER] to confirm or Press [MODE/ESC] to return to the main menu.

- Lamp on/off via external controller

With this function you can switch the lamp on or off via an external controller.

1. Select ‘’ONLI’’ by pressing [UP] or [DOWN] button.

2. Press [ENTER], the display shows ‘’ON’’ or ‘’OFF’’.

3. Press [UP] to select ‘’ON’’ if you wish to enable this function or press [DOWN] button to ‘’OFF’’ if

you don’t.

4. Press [ENTER] to confirm or Press [MODE/ESC] to return to the main menu.

- Delay lamp on

With this function you can delay the lamp ignition.

1. Select ‘’DELA’’ by pressing [UP] or [DOWN] button.

2. Press [ENTER], the display shows “D-XX”,”XX” stands for the version number, e.g. “D-15” (default

setting is 15 minutes for lamp delay time)

3. Press [UP] or [DOWN] to set the desired value for lamp delay time.

4. Press [ENTER] to confirm or Press [MODE/ESC] to return to the main menu.

- Main menu 2

1. Press [MODE/ESC] to enter the main menu (display flashing).

2. Press [UP] or [DOWN] button. to select ‘’SET’’.

SGM Technology for Lighting GB

WIT070 V1.0-01NR Idea Spot 250

14

- Pan Reverse

With this function you can reverse the Pan-movement.

1. Select ‘’RPAN’’ by pressing [UP] or [DOWN] button.

2. Press [ENTER], the display shows ‘’ON’’ or ‘’OFF’’.

3. Press [UP] to select ‘’ON’’ if you wish to enable this function or press [DOWN] button to ‘’OFF’’ if you

don’t.

4. Press [ENTER] to confirm or Press [MODE/ESC] to return to the main menu.

- Tilt Reverse

With this function you can reverse the Tilt-movement.

1. Select ‘’RTIL’’ by pressing [UP] or [DOWN] button.

2. Press [ENTER], the display shows ‘’ON’’ or ‘’OFF’’.

3. Press [UP] to select ‘’ON’’ if you wish to enable this function or press [DOWN] button to ‘’OFF’’ if you

don’t.

4. Press [ENTER] to confirm or Press [MODE/ESC] to return to the main menu.

- Switch 16 bit/8 bit

With this function you can switch the device from 16 bit to 8 bit resolution.

1. Select ‘’16BI’’ by pressing [UP] or [DOWN] button.

2. Press [ENTER], the display shows ‘’ON’’ or ‘’OFF’’.

3. Press [UP] to select ‘’ON’’ if you wish to enable this function or press ‘’DOWN’’ button to ‘’OFF’’ if

you don’t.

4. Press [ENTER] to confirm or Press [MODE/ESC] to return to the main menu.

- Pan degree select

With this function you can select pan angle 630

0

or 540

0.

1. Select “DEGR” by pressing [UP] or [DOWN] button.

2. Press [ENTER], the display shows “630” or “540”.

3. Press [UP] or [DOWN] button to select “630” or “540”, the default is 630.

4. Press [ENTER] to confirm or Press [MODE/ESC] to return to the main menu.

- Dimmer speed select

With this function you can select dimmer speed “slow” and “fast”.

1. Select “DIMM” by pressing [UP] or [DOWN] button.

2. Press [ENTER], the display shows “SLOW” or “FAST”.

3. Press [UP] or [DOWN] button to select “SLOW” or “FAST”.

4. Press [ENTER] to confirm or Press [MODE/ESC] to return to the main menu.

-Mic sensitivity

With this function you can adjust the sensitivity of the microphone.

1. Select ‘’MIC’’ by pressing [UP] or [DOWN] button.

2. Press [ENTER], the display shows ‘’M-XX’’, ‘’XX’’ stands for the number from 0 to 99.

3. Press [ENTER] to confirm or Press [MODE/ESC] to return to the main menu.

-Automatic Run by no DMX

With this function you can automatic run the device by no DMX.

1. Select ‘’AUTO’’ by pressing [UP] or [DOWN] button.

2. Press [ENTER], the display shows “CLOS”, “HOLD”, “AUTO” or “AUDI”.

3. Press [UP] or [DOWN] button to select “CLOS”, “HOLD”, “AUTO” or “AUDI”, the default is “HOLD”.

4. Press [ENTER] to confirm or Press [MODE/ESC] to return to the main menu.

- Fan’s mode select

With this function you can select the Fan’s mode.

1. Select “FANS” by pressing [UP] or [DOWN] button.

2. Press [ENTER], the display shows “HIGH” or “AUTO”.

3. Select “HIGH” or “AUTO” by pressing [UP] or [DOWN] button.

4. Press [ENTER] to confirm or Press [MODE/ESC] to return to the main menu.

GB SGM Technology for Lighting

Idea Spot 250 WIT070 V1.0-01NR

15

- Movement mode select

With this function you can select the movement mode.

1. Select “SPEE” by pressing [UP] or [DOWN] button.

2. Press [ENTER], the display shows “SP-1” or “SP-2”.

3. Select “SP-1” or “SP-2” by pressing [UP] or [DOWN] button.

4. Press [ENTER] to confirm or Press [MODE/ESC] to return to the main menu.

- Reset

With this function you can Reset the device via the Control Board.

1. Select ‘’REST’’by pressing [UP] or [DOWN] button.

2. Press [ENTER] to confirm or Press [MODE/ESC] to return to the main menu.

- Restore factory settings

With this function you can restore the factory settings of the device. All settings will be set back to the

default values (shaded). Any edited scenes will be lost.

1. Select ‘’LODA’’ by pressing [UP] or [DOWN] button.

2. Press [ENTER], the display shows ‘’ON’’ or ‘’OFF’’.

3. Press [UP] to select ‘’ON’’ if you wish to enable this function or press [DOWN] button to ‘’OFF’’ if you

don’t.

4. Press [ENTER] to confirm or Press [MODE/ESC] to return to the main menu.

- Software version

With this function you can display the software version of the device.

1. Select ‘’VER’’ by pressing [UP] or [DOWN] button.

2. Press [ENTER], the display will show ”V-XX”, "XX" stands for the version number, e.g. “V-1.0”,

“V-2.6”.

3. Press [MODE/ESC] to return to the main menu.

- Main menu 3

1. Press [MODE/ESC] to enter the main menu (display flashing).

2. Press [UP] or [DOWN] button to select ‘’ADJU’’.

- Lamp adjustment

With this function you can adjust the lamp via the Control Board. The shutter opens and the lamp can be

adjusted. In this mode, the device will not react to any control signal.

1. Select ‘’LADJ’’ by pressing [UP] or [DOWN] button.

2. Press [ENTER], the display shows ‘’ON’’ or ‘’OFF’’.

3. Press [UP] to select ‘’ON’’ if you wish to enable this function or press [DOWN] button to select ‘OFF’

if you don’t.

4. Press [ENTER] to confirm or Press [MODE/ESC] to return to the main menu.

- Test function of each channel

With this function you can test each channel on its (correct) function.

1. Select ‘’TEST’’ by pressing [UP] button.

2. Press [ENTER], the display shows ‘’T-XX’’, “X” stands for the channel number.

3. The current channel will be tested.

4. Select the desired channel by pressing [UP] or [DOWN] button.

5. Press [ENTER] to confirm or Press [MODE/ESC] to return to the main menu.

SGM Technology for Lighting GB

WIT070 V1.0-01NR Idea Spot 250

16

- Fixture code and motor fix

1. Select “WHEL” by pressing [UP] or [DOWN] button.

2. Press [ENTER], the display shows “CODE” or “CH01-CH30”.

3. Select “CODE” or “CH01-CH30” by pressing [UP] or [DOWN] button.

4. Press [ENTER] to confirm or Press [MODE/ESC] to return to the main menu.

- Main menu 4

1. Press [MODE/ESC] to enter the main menu (display flashing).

2. Press [UP] or [DOWN] button to select ‘’TIME’’.

- Fixture running time

With this function you can display the running time of the device.

1. Select ‘’MATI’’ by pressing [UP] or [DOWN] button.

2. Press [ENTER], the display shows ‘’XXXX’’, “X” stands for the number of hours.

3. Press [ENTER] to confirm or Press [MODE/ESC] to return to the main menu.

- Lamp running time

With this function you can display the running time of the lamp.

1. Select ‘’LATI’’ by pressing [UP] button.

2. Press [ENTER], the display shows ‘’XXXX’’, “X” stands for the number of hours.

3. Press [MODE/ESC] to return to the main menu.

- Clear fixture time

With this function you can clear the running time of the device.

1. Select ‘’CLMT’’ by pressing [UP] or [DOWN] button.

2. Press [ENTER], the display shows ‘’ON’’ or ‘’OFF’’.

3. Press [UP] to select ‘’ON’’ if you wish to enable this function or press [DOWN] button to ‘’OFF’’ if you

don’t.

4. Press [ENTER] to confirm or Press [MODE/ESC] to return to the main menu.

- Clear lamp time

With this function you can clear the running time of the lamp. Please clear the lamp time every time you

replace the lamp.

1. Select ‘’CLLT’’ by pressing [UP] or [DOWN] button.

2. Press [ENTER], the display shows ‘’ON’’ or ‘’OFF’’.

3. Press [UP] to select ‘’ON’’ if you wish to enable this function or press [DOWN] button to ‘’OFF’’ if you

don’t.

4. Press [ENTER] to confirm or Press [MODE/ESC] to return to the main menu.

GB SGM Technology for Lighting

Idea Spot 250 WIT070 V1.0-01NR

17

- Main menu 5

1. Press [MODE/ESC] to enter the main menu (display flashing).

2. Press [UP] or [DOWN] button to select ‘’EDIT’’.

- Define the number of steps in Run

With this function you can define the number of steps in the

Program Run.

1. Select ‘’STEP’’ by pressing [UP] or [DOWN] button.

2. Press [ENTER], the display shows ‘’S-XX’’, “X” stands

for the total amount of steps you want to save, so you

can call up to 48 scenes in ‘’RUN’’. For example if the

“XX” is 05, it means that ‘’RUN’’ will run the first 5

scenes you saved in ‘’EDIT’’.

3. Press [ENTER] to confirm or Press [MODE/ESC] to

return to the main menu.

-Auto Save

With this function you can automatic save the number of

steps in the Program Run.

1. Select “REC” by pressing [UP] or [DOWN] button.

2. Press [ENTER], the display shows “RE.XX”, “XX”

stands for the number from 1 to 400.

3. Press [ENTER] to confirm or Press [MODE/ESC] to

return to the main menu.

SGM Technology for Lighting GB

WIT070 V1.0-01NR Idea Spot 250

18

- Editing the channels of the individual scenes

With this function you can edit the program to be called up in Run.

a) Editing via the Control Board

1. Select ‘’SC01’’ by pressing [UP] or [DOWN] button.

2. Press [ENTER], the display shows ‘’SCXX’’, ‘’X’’ stands for the scene no. to be edited.

3. Change the scene no. by pressing [UP] or [DOWN] button.

4. Press [ENTER], the display shows ‘’C-X’’, ‘’X’’ stands for the channel no. Such as ‘’C-01’’, it means

you are editing channel 1 of the selected scene.

5. Select the channel no. you would like to edit by pressing [UP] or [DOWN] button.

6. Press [ENTER] to enter editing for the selected channel, the fixture reacts to your settings. The

display shows the DMX value of the edited channel. Such as ‘’11XX’’, it stands for in the channel 11 of

the editing scene, the DMX value is XX , XX is a hexadecimal number value ‘’01-FF’’.

7. Adjust the desired DMX value by pressing [UP] or [DOWN] button.

8. Press [ENTER] in order to edit other channels of this scene.

9. Repeat steps 5-9 until you finish setting all the DMX values for all channels of this scene.

10. Once all the channels completed, the display will flash ‘’TIME’’

11. Press [ENTER] to edit the time needed, the display shows “TXXX” , “XXX” stands for the time needed

to run the current scene, value “001-999”. E.g., “002” means you need 0.4ms (002*0.2ms) to run the

current scene.

12. Adjust the desired time by pressing [UP] or [DOWN] button.

13. Press [ENTER] to save the settings for the scene you are editing, the display will change to the next

scene automatically.

14. Repeat step 3-14 to edit and other scenes, you can edit and save a maximum of 48 scenes.

15. Press [MODE/ESC] to exit. The number of steps can be defined under ‘STEP’ and the scenes can be

called up under ‘’RUN’’

b)

Editing via the external controller

Call up the first scene in your controller now.

1. Select ‘’SC01’’ by pressing [UP] or [DOWN] button.

2. Press [ENTER], the display shows ‘’SC01’’.

3. Press [ENTER], the display shows ‘’C-01’’.

4. Select "CNIN" by pressing [UP] or [DOWN] button.

5. Press [ENTER], the display shows "OFF".

6. Press [UP] or [DOWN] button .the display shows "ON".

7. Press [ENTER], the display shows "SC02". You successfully downloaded the first scene.

8. Adjust the Step-time as described above under point 12.

9. Call up the second scene in your controller now.

10. Repeat steps 5-11 until all desired scenes are downloaded.

11. Press [MODE/ESC] to exit. The number of steps can be defined under ’STEP’ and the scenes can be

called up under ‘’RUN’’

La pagina sta caricando ...

SGM IDEA SPOT 250 Manuale utente

SGM IDEA SPOT 250 Manuale utente

in altre lingue

Documenti correlati

Altri documenti