SGM IDEA SPOT 700 Manuale utente

Marca: SGM

Modello: IDEA SPOT 700

Categoria: Macchina per la riduzione del rumore

Tipo: Manuale utente

00.1 .LE

R LAUN

AMS’

RES

M O VING HEADS

IDEA SPOT 700

Vi ringraziamo per aver acquistato un prodotto SGM.

Per ottenere i migliori risultati dal suo utilizzo, vi preghiamo di leggere attentamente questo manuale di istruzioni.

Al suo interno troverete le informazioni tecniche e le specifiche d’uso del prodotto. Nelle pagine in appendice tro-

verete inoltre schemi e diagrammi destinati all’assistenza tecnica.

Nell’ottica di qualità SGM, è possibile che l’Azienda apporti migliorie ai suoi prodotti, per cui consigliamo di alle-

gare il manuale al prodotto stesso e di trascrivere il numero di serie nell’ultima pagina della copertina: utilizzando

il presente manuale con un apparecchio fabbricato prima o dopo la sua stampa, potrebbero esserci discrepanze

fra l’apparecchio e quanto riportato nel manuale stesso.

Thank you for buying an SGM product.

To obtain the best results, please carefully read this instruction manual in which you will find technical information

and specifications for use of the product, as well as diagrams for technical service in the appendix.

In light of SGM quality, the company may make improvements to its products. Therefore, we recommend that the

manual be attached to the product and the serial number copied onto the back cover: using this manual with

equipment manufactured before or after its printing, might show discrepancies between the equipment and the

information listed in the manual.

Wir danken Ihnen für den Kauf eines Produkts von SGM.

Zur Erzielung der besten Resultate bei der Benutzung bitten wir Sie, die vorliegende Bedienungsanleitung aufmerk-

sam zu lesen. Darin finden Sie die technischen Informationen sowie die Anweisungen für die Benutzung des

Produkts. Im Anhang befinden sich auBerdem die Schaltpläne undv Diagramme für den Kundendienst.

SGM behält sich das Recht vor, Verbesserungen an den Produkten vorzunehmen und deshalb empfehlen wir, die

Bedienungsanleitung dem Produkt stets beizulegen und die Seriennummer auf der letzten Seite des Umschlags

einzutragen. Bei der Verwendung dieses Handbuches mit einem Gerät, das vor oder nach der Drucklegung produ-

ziert wurde, können sich Abweichungen zwischen Gerät und dem Inhalt des Handbuches ergeben.

Nous vous remercions d’avoir acheté un produit SGM.

Pour optimiser son utilisation, nous vous prions de bien vouloir lire attentivement cette notice où vous trouverez

les informations techniques et les caractéristiques d’utilisation du produit. En outre, vous trouverez également,

dans les pages en appendice, les schémas et les diagrammes concernant l’assistance technique.

Le concept de qualité SGM, lui permet d’améliorer continuellement ses produits et c’est pourquoi nous vous con-

seillons de joindre la notice au produit et d’inscrire le numéro de sèrie sur la page de couverture. En effet, si on

l’utilise avec un appareil fabriqué avant ou après son impression, il peut y avoir des différences entre l’appareil et

ce qui figure dans la notice.

Les estamos sumamente agradecidos por haber elegido un producto SGM.

Para obtener los mejores resultados, les rogamos leer detenidamente el presente manual de instrucciones. El

mismo contiene las informaciones técnicas y las indicaciones de uso del producto. Las páginas anexas contienen

además los esquemas y diagramas necesarios para la asistencia técnica.

Para mantener la calidad SGM, es posible que la Empresa aporte mejoras sus productos, por ello les aconsejamos

conservar el manual junto con el aparato correspondiente y escribir su número de serie en la última página del

manual; si en cambio se utiliza el presente manual con un aparato frabicado antes o después de su impresión, es

probable que existan discrepancias entre el aparato y las indicaciones del mismo.

GB SGM

Idea Spot 700 XM473-V1.0-NR

１

Table of Contents

INTRODUCTION: ....................................................................................................................... ２

Features: ........................................................................................................................... ２

OVERVIEW................................................................................................................................３

GENERAL GUIDELINES ............................................................................................................... ５

INSTALLATION INSTRUCTIONS.................................................................................................... ５

Installing or replacing the lamp ............................................................................................. ５

Mounting the device ............................................................................................................ ７

Installation method via clamp ...............................................................................................８

DMX-512 control connection .................................................................................................８

Control Board .................................................................................................................. １１

FUNCTION MODE .................................................................................................................... １３

DMX Address Setting ........................................................................................................ １３

Display the DMX 512 value of each channel ......................................................................... １３

Slave Setting ................................................................................................................... １３

Auto Program .................................................................................................................. １３

Music control ................................................................................................................... １３

INFORMATION........................................................................................................................ １３

Time information.............................................................................................................. １３

Current Time ................................................................................................................... １３

Software version .............................................................................................................. １４

LAMP CONTROL ...................................................................................................................... １４

PERSONALITY......................................................................................................................... １５

RESET-FUNCTIONS ................................................................................................................. １６

EFFECT ADJUST...................................................................................................................... １６

USERS MODE SET................................................................................................................... １６

EDIT PROGRAM ...................................................................................................................... １６

INSTRUCTIONS ON USE: ......................................................................................................... １９

ERROR MESSAGE.................................................................................................................... ２４

CLEANING AND MAINTENANCE................................................................................................. ２５

TECHNICAL SPECIFICATIONS ................................................................................................... ２５

SGM GB

XM473-V1.0-NR Idea Spot 700

２

KEEP THIS MANUAL FOR FUTURE NEEDS

Thank you for your patronage. We are confident that our excellent products and service can satisfy you.

For your own safety, please read this user manual carefully before installing the device.

CAUTION !

Keep this device away from rain and moisture!

Unplug mains lead before opening the housing

Every person involved with the installation, operation and maintenance of this device has to:

-be qualified

-follow carefully the instructions of this manual

INTRODUCTION:

Thank you for having chosen this professional moving head.

You will see you have acquired a powerful and versatile device.

Unpack the device. Inside the box you should find: the fixture device, an XLR connection cable, a safety

rope, two omega clamps and this manual. Please check carefully that there is no damage caused by

transportation. Should there be any, consult your dealer and don’t install this device.

Features:

 Lamp: Philips MSR GOLD 700 SA/2 DE

 3 Control channel modes: 24 / 22 / 34 channels

 Stand alone operation with master/slave function, can be sound activated

 Pan/tilt movement: - 8 bit and 16 bit resolution

- For smooth and precise resolution

- Pan: 540°/630° optional, Tilt: 265°movement

- High speed of pan/tilt movement, speed of pan/tilt movement is adjustable

- Scan position memory, auto reposition after unexpected movement

 Motorized color wheel with 8 interchangeable dichroic filters and open, rainbow-effect with adjustable

speed in both directions

 CMY color mixture to get indefinite color effects

 30 CMY and color wheel MACROS and Random CMY

 Two rotation gobo wheel with 6 interchangeable rotating gobos plus open each, both 2 gobo wheels

have different speed of gobo shaking and rainbow effect, and gobo indexing

 ”Slot in & out” gobo/color wheel system

 Animation flame effect

 Prism : 3 –facet speed adjustable prism rotates in two directions with 16 prism macros effect

 Strobe effect with 1-13 flashes per second or random strobe via shutter

 Motorized focus

 Zoom: 15°~30° linear zoom

 Dimmer: 0%~100% full range dimming

 Iris from 5%~100% with pulse iris effect.

 Stepless frost, 0%~100% linear change frost

 Bule LCD display

 Preset program: 7 built in programs can be called up via DMX controller

 Editable program: Edit and save the program to inside EEPROM via the control board or external

controller, up to 250 scenes can be saved and then can be run in Stand Alone or sound activated

 Number of scenes in Program Run can be changed individually

GB SGM

Idea Spot 700 XM473-V1.0-NR

３

OVERVIEW

1. Objective-lens

2. LCD-Display

3. Mode/Esc-button

4. Up-button

5. Down-button

6. Enter-button

7. Microphone

8. Wireless DMX antenna

9. Wireless indicator

10. Lamp system

11. Yoke

12. Carrying handle

13. DMX output socket

14. DMX input socket

15. Fuse

16. Power supply

SGM GB

XM473-V1.0-NR Idea Spot 700

４

SAFETY INSTRUCTIONS

CAUTION

Be careful with your operations. With a dangerous voltage you can Suffer a

dangerous electric shock when touching wires!

This device has left the factory in perfect condition. In order to maintain this condition and to ensure a safe

operation, it is absolutely necessary for the user to follow the safety instructions and warning notes written

in this user manual.

IMPORTANT

Damages caused by the disgregard of this user manual are not subject to warrenty.

The dealer will not accept liability for any resulting defects or problems.

If the device has been exposed to temperature changes due to environmental changes, do not switch it on

immediately. The arising condensation could damage the device. Leave the device switched off until it has

reached room temperature.

This device falls under protection-class I. Therefore it is essential that the device be earthed.

The electric connection must carry out by qualified person.

The device shall only be used with rate voltage and frequency.

Make sure that the available voltage is not higher than stated at the end of this manual.

Make sure the power cord is never crimped or damaged by sharp edges. If this would be the case,

replacement of the cable must be done by an authorized dealer.

Always disconnect from the mains, when the device is not in use or before cleaning it. Only handle the

power cord by the plug. Never pull out the plug by tugging the power cord.

During initial start-up some smoke or smell may arise. This is a normal process and does not necessarily

mean that the device is defective, it should decrease gradually.

Please don't project the beam onto combustible substances.

Fixtures cannot be installed on combustible substances, keep more than 50cm distance with wall for

smooth air flow, so there should be no shelter for fans and ventilation for heat radiation.

If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the

manufacturer or his service agent or a similar qualified person in order to avoid a hazard.

CAUTION

Never touch device during operation!

The housing may heat up.

Never look directly into the light source,

as sensitive persons may suffer an epileptic shock.

Please be aware that damages caused by manual modifications to the device are not subject to warranty.

Keep away from children and non-professionals.

GB SGM

Idea Spot 700 XM473-V1.0-NR

５

GENERAL GUIDELINES

This device is a lighting effect for professional use on stages, in discotheques, theatres, etc.

This fixture is only allowed to be operated with the max alternating current which stated in the technical

specifications in the last page of this manual, the device was designed for indoor use only.

Lighting effects are not designed for permanent operation. Consistent operation breaks may ensure that

the device will serve you for a long time without defects. Do not shake the device.

Avoid brute force when installing or operating the device.

The device shall only be used complete with its protective shield.

While choosing the installation-spot, please make sure that the device is not exposed to extreme heat,

moisture or dust. The minimum distance between light-output from the projector and the illuminated

surface must be more than 0.5 meter, Lighting can not be installed where there is combustible.

Always fix the fixture with an appropriate safety cable if you use the quick lock cam in hanging up the

fixture, please make sure the 4 quick lock fasteners turned in the quick lock holes correctly.

If you use the quick lock cam in hanging up the fixture, please make sure the 4 quick lock fasteners turned

in the quick lock holes correctly.

Operate the device only after having familiarized with its functions. Do not permit operation by persons not

qualified for operating the device. Most damages are the result of unprofessional operation.

Please use the original packaging if the device is to be transported.

For safety reasons, please be aware that all modifications on the device are forbidden.

If this device will be operated in any way different to the one described in this manual, the product may

suffer damages and the guarantee becomes void. Furthermore, any other operation may lead to

short-circuit, burns, electric shock, lamp explosion, crash, etc.

INSTALLATION INSTRUCTIONS

Installing or replacing the lamp

CAUTION

Only install the lamp with the device unplugged from the mains.

The lamp has to be replaced when it is damaged or deformed.

Before replacing the lamp let the lamp cool down, because during operation, the lamp can reach very high

temperature.

During the installation of halogen lamps do not touch the glass bulbs bare handed. Always use a cloth to

handle the lamps during insertion and removal.

Do not install lamps with a higher wattage. They generate higher temperatures than which the device was

designed for.

SGM GB

XM473-V1.0-NR Idea Spot 700

６

For the installation, you need one Philips MSR GOLD 700 SA/2 DE

Procedure:

Unscrew the 4 screws A, B, C and D on the bottom of the housing, holding the plate where the lamp is

underneath.

Gently pull the socket holder using the knob in the middle.

Carefully insert the lamp into the socket. Please remember there is only one way to insert the lamp.

Gently slide the lamp and its lamp holder back into place and fasten the 4 screws.

On the access plate there are 3 small screws marked 1, 2 and 3.which are used to adjust the lamp

holder in the lamp housing. You can adjust the 3 screws to fine-turn the position of the lamp to get the

maximum light output as shown below.

Please remember the lamp is not a hot-restrike type, you must wait for approximately 15 minutes after

having turned off the lamp before you can turn it back on again.

CAUTION

Do not operate this device with open cover.

GB SGM

Idea Spot 700 XM473-V1.0-NR

７

Mounting the device

CAUTION

Pleas consider the EN 60598-2-17 and the other respective national norms

during the installation. The installation must only be carried out by a

qualified person.

The applicable temperature for the lignting is between -25°C to 45°C. Do not use the lighting under or

above the temperature.

The installation of the effect has to be built and constructed in a way that it can hold 10 times the weight

for 1 hour without any harming deformation.

The installation must always be secured with a secondary safety attachment, e.g. an appropriate safety

rope.

Never stand directly below the device when mounting, removing or servicing the fixture.

The operator has to make sure the safety relating and machine technical installations are approved by an

expert before taking the device into operation for the first time.

These installations have to be approved by a skilled person once a year.

The lighting should be put in a relatively broad space. Ensure there is no barrier in the range of 50cm²

around the lighting.

CAUTION

Before

taking into operation for the first time, the installation has to be

approved by an expert.

Cautions:

The effect should be installed outside areas where persons may reach it, walk by or be seated.

CAUTION

When installing the device, make sure there in no highly inflammable

material within a distance of min. 0,5m

Overhead mounting requires extensive experience, including amongst others calculating working load

limits, installation material being used, and periodic safety inspection of all installation material and the

device. If you lack these qualifications, do not attempt the installation yourself. Improper installation can

result in bodily injury.

CAUTION

The electric connection must only be carried out by a qualified electrician.

Before mounting make sure that the installation area can hold a minimum point load of 10 times the

device’s weight.

Connect the fixture to the mains with the power plug

SGM GB

XM473-V1.0-NR Idea Spot 700

８

Installation method via clamp

Please refer to the picture below:

Screw one clamp each via a M12 screw and nut onto the Omega holders.

Insert the quick-lock fasteners of the first Omega holder into the respective holes on the bottom of the

device. Tighten the quick-lock fasteners fully clockwise. Install the second Omega holder.

Pull the safety-rope through the holes on the bottom of the base and over the trussing system or a safe

fixation spot. Insert the end in the carabine and tighten the safety screw.

DMX-512 control connection

Connect the provided XLR cable to the female 5-pin XLR output of your controller and the other side to the

male 5-pin XLR input of the moving head. You can chain multiple

Moving head together through serial linking. The cable needed should be two core, screened cable with XLR

input and output connectors. Please refer to the diagram below.

GB SGM

Idea Spot 700 XM473-V1.0-NR

９

Starting address 49 Starting address 25 Starting address 1

DMX-512 connection with DMX terminator

For installations where the DMX cable has to run a long distance or is in an electrically noisy environment,

such as in a discotheque, it is recommended to use a DMX terminator. This helps in preventing corruption

of the digital control signal by electrical noise. The DMX terminator is simply an XLR plug with a 120 Ω

resistor connected between pins 2 and 3,which is then plugged into the output XLR socket of the last fixture

in the chain. Please see illustrations below.

Projector DMX starting address selection

All fixtures should be given a DMX starting address when using a DMX signal, so that the correct fixture

responds to the correct control signals. This digital starting address is the channel number from which the

fixture starts to “listen” to the digital control information sent out from the DMX controller. The allocation

of this starting address is achieved by setting the correct number on the display located on the base of the

device.

You can set the same starting address for all fixtures or a group of fixtures, or make different address for

each fixture individually.

If you set the same address, all the units will start to “listen” to the same control signal from the same

channel number. In other words, changing the settings of one channel will affect all the fixtures

simultaneously.

If you set a different address, each unit will start to “listen” to the channel number you have set, based on

the quantity of control channels of the unit. That means changing the settings of one channel will affect

only the selected fixture.

In the case of the moving head, which is 24 channels fixture, you should set the starting address of the first

unit to 1, the second unit to 25(24 + 1), the third unit to 49 (25+ 24), and so on.

SGM GB

XM473-V1.0-NR Idea Spot 700

１０

Operting instructions of the internal DMX wireless system

1. Equipments:

DMX 512 controller, wireless transmitter, and the fixtures with wireless receiver.

2. Message from the LED indicator:

1. Rapid flashing red/Green: logging in to a transmitter

2. Slow flashing Red/Green: Logged on a transmitter and the DMX line is idle (No DMX is connected

to transmitter).

3. Solid Green: Logged on to a transmitter and receiving DMX data.

4. Solid Red: Not logged on to a transmitter (free)

3. DMX in the menu of the fixture:

On a fixture installed with wireless system, in order to switch between wireless control system and

traditional DMX control (with cable), a new menu WDMX is added to the display board.

ON: (Activate WDMX)

1. When the fixture is on power，and the WDMX is activated to ON status, but did not connect to the

controller and did not log in to the transmitter, the fixture will search for the DMX signal source. If

the fixture is connected to the DMX controller it can be controlled by DMX controller; if it is log in

to the wireless transmitter, it can be controlled by the Transmitter

2. When the fixture is power off, and the WDMX is in ON status, if the fixture is connected to DMX

controller. After the fixture is power on, it can be controlled only by the DMX controller which

connected. The fixture can log in the wireless transmitter, and receive only radio signal from

transmitter, but not DMX from the transmitter.

OFF: (De-activate WDMX)

In this status, wireless system is not activated, so the fixture can not log in the transmitter.

REST: (reset WDMX memory);

Can remove the fixture from the connection with the transmitter, the fixture become free and ready

to log in any transmitter.

OUT:（Act & Data Out）

4. Setup the wireless system:

1. Connect the transmitter with the DMX controller

2. To make the fixture installed with wireless receiver log in to the transmitter

a) Initially, the indicator on the receiver fixture should be in Solid red

b) Press and hold the configuration button on transmitter for less than 3 seconds the red/green

LEDs on the transmitter and the receiver fixture will flash rapidly for about 5~ 10 seconds while

the system goes through its setup procedure.

c) Once the receiver fixture is logged in to the transmitter (T1), the fixture with wireless receiver

will keep the memory, even if restart the power, this unit will log in the transmitter (T1)

automatically.

3. Use the DMX 512 to control the fixture

5. Remove the receivers from transmitter (T1) and to log in to another transmitter (T2)

Case 1: Remove a receiver:

a) On the control board of the fixture, enter menu to activated the function of REST;

b) The LED for wireless on the fixture should turn to Solid red; the receiver can log out from the

transmitter (T1);

c) press the configuration button on transmitter(T2) for less than 3 second, then the fixture will start

to connect with the transmitter(T2)

Case 2: Remove all receivers from a transmitter (T1) to log in to T2;

a) Press and hold the configuration button on the T1 as least 5 seconds, can clear the connection with

all the fixtures.

b) All the red/green LEDs on the receiver fixtures will turn to Solid red to indicate that the receivers

are unassigned and removed from the transmitter ( T1);

c) Press and hold the configuration button on the T2 less then less than 3 second , the fixtures will

connect with the T2

PS:

1. Please log the receivers out from the transmitter after every job, so that the receivers are in free un

assigned state and ready to be assigned to a transmitter.

2. Do not connect the fixture which is under the communication of wireless system to the DMX controller,

otherwise it will cause interference from the DMX controller.

GB SGM

Idea Spot 700 XM473-V1.0-NR

１１

Control Board

The Control Board offers several features: you can simply set the starting address, switch on and off the

lamp, run the pre-programmed program or make a reset.

The main menu is accessed by pressing the Mode/esc-button until the display starts flashing. Browse

through the menu by pressing the Up-button or Down-button. Press the Enter-button in order to select

the desired menu. You can change the selection by pressing the Up-button or Down-button. Confirm every

selection by pressing the Enter-button. You can leave every mode by pressing the Mode/esc-button. The

functions provided are described in the following sections.

To access the display menu via the internal battery, press the UP or DOWN button. The display

will automatically switch off about 10 seconds after the last actuation of the buttons.

Default settings shaded

Function

Mode

Set Dmx Address

Value Display

Set To Slave

Auto Program

Music Control

A001~AXXX

PAN……

Slave1,Slave2,Slave3

Master / Alone

DMX address setting

DMX value display

Slave setting

Auto program

Music control

Time Information Current Time

Total Life Hours

Last Run Hours

Lamp Hours

Lamp Off Time

Timer Password

Clear Last Run

L-Timer Password

Clear Lamp Time

XXXX(Hours)

XXXX(Minute)

Password=XXX

ON/OFF

Password=XXX

ON/OFF

Power on running time

Fixture running time

Fixture Last times clear

Lamp running time

Lamp off time

Timer Password 038

Clear Fixture Last time

Lamp Password Code=”038”

Clear lamp time

Temperature Info Head Temperature XXX°C/°F Temperature in the head

Information

Software Version Ver1.0…… Software version of each IC

Lamp Control

Lamp On or Off

Automatic La-On

Lamp On Via DMX

Lamp Off Via DMX

Lamp On at Temp.

Lamp Off at Temp.

ON/OFF

20~79°C,45°C /68~174°F 113°F

80~139°C, 130°C /176~282°F, 266°F

Lamp on/off

Lamp on/off when Power on

Lamp on via DMX

Lamp off via DMX

Lamp restart at temp.

Lamp off at temp.

Status Settings Address via DMX

No DMX Status

Pan Reverse

Tilt Reverse

Pan Degree

Feedback

Movement Speed

Mic Sensitivity

Hibernation

ON/OFF

Close/Hold/Auto/Music

ON/OFF

630/540

ON/OFF

Speed 1~ 4

0~99%

0FF/1~99M，15M

Add. via DMX

Auto run if no DMX

Pan Reverse movement

Tilt Reverse movement

Pan Degree Select

Movement Feedback switch

Movement Mode Select

Sensitivity of Mic.

Stand by mode

Service Setting Service Password

Fan Voltage

Gobo Speed

Password=XXX

High/Low

Quick/Slow

Service Code“=050”

Fan Voltage Select

Gobo Change Speed

Fans Control Auto Fans Speed

High Fans Speed

Low Fans Speed

Fans Speed Mode Select

Personality

Display Setting

Shutoff Time

02~59m 05m

Display shutoff time

SGM GB

XM473-V1.0-NR Idea Spot 700

１２

Key Lock ON/OFF Key Lock

Temperature C/F

Celsius

Fahrenheit

Temperature switch

between °C/°F

Initial Effect PAN…… PAN =XXX Initial effect position

Wireless DMX

De-Act WDMX

Activate WDMX

Act & Data Out

Rest WDMX Mem

De-activate WDMX

Activate WDMX

Act & Data Out

Reset Wireless DMX Mem

Reset Default ON/OFF Restore factory set.

Reset Function

Reset All

Reset Pan&Tilt

Reset Colors

Reset Gobos

Reset Shutter

Reset Others

Reset all motors

Reset Pan/Tilt

Reset color wheel

Reset gobos

Reset shutter and/or

dimmer

Reset other motors

Test Channel PAN …… Test function

Manual Control PAN

PAN =XXX

Fine adjustment of the lamp

Effect Adjust

Calibrate Values --Password--

Color wheel

Password=XXX

Color wheel=XXX

Calbrate and adjust the

effects to standard/right

position Password “050”

User Mode

Standard Mode

Basic Mode

Extended Mode

User Mode A

User Mode B

User Mode C

User’s mode to change

channel numbers

Users Mode Set

Edit User Mode Max Channel

PAN

Max Channel = XX

PAN = CH01

Preset User modes

Select Programs Auto Pro Part 1

Auto Pro Part 2

Auto Pro Part 3

Program 1 ~ 10 Program 1

Program 1 ~ 10 Program 2

Program 1 ~ 10 Program 3

Select programs to be run

Edit Program Program 1

Program 10

Program Test

Step 01=SCxxx

Step 64=SCxxx

(“STEP XX”)

Testing program

Program in loop

Save and exit

Edit Scenes Edit Scene 001

~ Edit Scene

250

Pan,Tilt,……

--Secne Time--

Input By Outside

Pan=xxx……

TIME=xx.xs

Save and automatically

return

manual scenes edit

Edit Program

Rec. Controller XX~XX Automat. scenes rec

GB SGM

Idea Spot 700 XM473-V1.0-NR

１３

FUNCTION MODE

DMX Address Setting

With this function, you can adjust the desired DMX-address via the Control Board.

 Select “Set DMX address” via the encoder.

 Press the encoder, adjust the DMX address by turning the encoder.

 Press the encoder to confirm.

 Press the Mode/Esc-button in order return to the main menu.

Display the DMX 512 value of each channel

With this function you can display the DMX 512 value of each channel. The display automatically shows the

channel with a value changing.

Slave Setting

With this function, you can define the device as slave.

Auto Program

With this function, you can run the internal program. You can select the desired program under “Select

program”. You can set the number of steps under “Edit program”. You can edit the individual scenes

under “Edit scenes”. With this function, you can run the individual scenes either automatically, i.e. with

the adjusted Step-Time.

Music control

With this function, you can run the internal program sound-controlled.

INFORMATION

Time information

Current Time

With this function, you can display the temporary running time of the device from the last power on. The

display shows “XXXX”, “XXXX” stands for the number of hours. The counter is resetted after turning the

device off.

Total Life Hours

With this function, you can display the running time of the device. The display shows “XXXX”, “XXXX”

stands for the number of hours.

Last Run Hours

With this function, you can display last the running time of the lamp. The display shows “XXXX”, “XXXX”

stands for the number of hours.

Lamp Hours

With this function, you can display the running time of the lamp. The display shows “XXXX”, “XXXX” stands

for the number of hours.

Lamp Off Time

With this function, you can display the temporary running time of the lamp from the last lamp on. The

display

Shows “XXXX”, “XXXX” stands for the number of hours. The counter is resetted after turning the lamp off.

Time Password

With this function, you can display the timer password. The time password is 038.

Clear Last Run

With this function, you can clear last run time of the fixture. The display shows “ON” or “OFF”, Press “Enter”

to confirm.

L-Time Password

With this function, you can display the timer password. The time password is 038.

SGM GB

XM473-V1.0-NR Idea Spot 700

１４

Clear LampTime

With this function you can clear the running time of the lamp. Please clear the lamp time every time you

replace the lamp.

 Select “Clear lamp time” by turning the encoder.

 Press the encoder, the display shows “ON” or “OFF”.

 Press the encoder to confirm.

 Press the Mode/Esc-button in order to return to the main menu.

Temp. Info.

Head Temp

With this function you can display the temperature on the display board of the base (near CMY-filter) in

Celsius.

Software version

With this function, you can display the software version of the device.

 Select “Software version” by turning the encoder.

 Press the encoder, the display shows “V-X.X”, “X.X” stands for the version number, e.g. “V-1.0”

 Turn the encoder in order to read the version of every individual IC.

 Press the Mode/Esc-button in order to return to the main menu.

LAMP CONTROL

When the real temperature around the lamp is higher than the preset value, the lamp will be shut down in

5 minutes automatically.

When the LCD display shows “Off”, it means the lamp must be turned on again manually;

When the LCD display shows “Hot”, it means the actual temperature around the lamp is still higher than the

preset value, so even the lamp can not be striked even the menu Lamp is turned to ON, as the lamp switch

is compelled to turned off.

When the temperature unit after the temperature value come to lowercase letter “c” or “f”, it means menu

Lamp is turned to ON, but the lamp is not full dimming up.

When the temperature unit after the temperature value come to capital letter “C” or “F”, it menu Lamp is

turned to ON, and the lamp is full intensity.

Lamp on/off

With this function you can switch the lamp on or off via the Control Board.

 Select "Lamp on/off" by turning the encoder.

 Press the encoder, the display shows “ON” or “OFF”.

 Turn the encoder to select “ON” if you wish to strike the lamp or “OFF” in order to switch it off.

 Press the encoder to confirm.

 Press the Mode/Esc-button in order to return to the main menu.

Remark: The menu Lamp On/Off is the software command only, the lamp can be striked successfully only

when the menu Lamp is set to ON and the actual temperature is lower than the limited value.

Lamp on/off when power on

With this function you can select if the lamp will be switched on when switching the power on. Select “ON”

by turning the encoder if you wish to enable this function or “OFF” if you don’t.

Lamp on via external controller

With this function you can select if you can switch the lamp on via an external controller (DMX-channel of

internal programs, value 64-79). Select “ON” by turning the encoder if you wish to enable this function or

“OFF” if you don’t.

Lamp off via external controller

With this function you can select if you can switch the lamp off via an external controller (DMX-channel of

internal programs, value 224-239). Select “ON” by turning the encoder if you wish to enable this function

or “OFF” if you don’t.

Lamp on at temp.

With this function you can set the inside temperature from which the projector will restrike the lamp after

automatic lamp shut off.

Lamp off at temp.

With this function you can set the inside temperature at which the projector will automatically switch the

lamp off. Turn the encoder to select the maximum inside temperature between 60° C and 159° C. Inside

temperatures below 90° C are not critical. 90° C and more should lead to the lamp being switched off.

GB SGM

Idea Spot 700 XM473-V1.0-NR

１５

Please note that the outside temperature should not exceed 45° C.

When the temperature around the lamp is higher than the preset value continuously up to 5

minutes, the lamp will be shut off automatically.

If the lamp be shut off automatically due to over heat, it can not be striked again automatically,

it must be turned on again by manually.

PERSONALITY

Status Settings

Address Via DMX

With this function, you can adjust the desired DMX-address via an external controller.

 Select “Address via DMX” by turning the encoder.

 Press the encoder, the display shows “ON” or “OFF”.

 Turn the encoder to select “ON” if you wish to enable this function or “OFF” if you don’t.

 Press the encoder to confirm.

 Press the Mode/Esc-button in order to return to the main menu.

 On the controller, set the DMX-value of channel 1 to "7".

 Set the DMX-value of channel 2 to "7"or "8". When set to "7" you can adjust the starting address

between 1 and 255. When set to "8" you can adjust the starting address between 256 and 511.

 Set the DMX-value of channel 3 to the desired starting address. If you want to set the starting address

to 57, set channel 1 to "7", channel 2 to "7" and channel 3 to "57". If you want to set the starting

address to 420,set channel 1 to "7", channel 2 to "8" and channel 3 to "164" (256+164=420).

 Wait for approx. 20 seconds and the unit will carry out a reset. After that, the new starting address is

set.

Hold If No DMX

With this function, when the drive is not DMX signal, it runs automatism, close, hold and music, the default

is hold.

Pan Reverse

With this function you can reverse the Pan-movement.

Tilt Reverse

With this function you can reverse the Tilt-movement.

Pan Degree

With this function, you can select pan degree for 630 or 540.

Feedback

With this function, you can feedback switch of pan movement or tilt movement.

Movement Speed

With this function, you can select scan mode from 1 to 4.

Mic Sensitivity

With this function, the default is 70%, you can select the desired microphone sensitivity from 0 % to 99 %.

Hibernation

Stand by mode - 0FF/1~99M，15M

Service Setting

Service Password

With this function, you can set the service password.

Fan Voltage

With this function, you can select fan voltage for high or low, the default is High.

Attention: The model is not recommended when ambient temperature is higher than 15 Celsius

degree.

Gobo speed

With this function, you can select GOBO speed for quick or slow, the default is Quick.

Fans Control

With this function, you can set the speed of the running fans. The selections have Auto、high and low.

SGM GB

XM473-V1.0-NR Idea Spot 700

１６

Display Setting

Shut off time

With this function you can shut off the LCD display after 2 to 59 minutes. Turn the encoder in order to select

the desired shut off time.

Key Lock

Key Lock -- ON/OFF

Temperature C/F

With this function, Display the temperature for Celsius or Fahrenheit.

Initial Effect

With this function, Display initial effect position.

Wireless DMX

From factory, this projector is prepared for wireless data transmission (W-DMX). If you wish to de-activate

W-DMX control, you can select the function “De-activate WDMX” by turning the encoder. With the function

“rest”, you can log out the projector from the wireless sender.

Reset Default

With this function, you can select restore factory set for ON or OFF, the default is OFF.

RESET-FUNCTIONS

With this function you can reset the device via the Control Board. You can select the different reset

functions by turning the encoder.

EFFECT ADJUST

Test function of each channel

With this function you can test each channel on its (correct) function.

Lamp adjustment

With this function, you can adjust the lamp more easily. All effects will be canceled, the shutter opens and

the dimmer intensity will be set to 100 %. With the individual functions, you can focus the light on a flat

surface (wall) and erform the fine lamp adjustment.

Calibrate values

With this function, you can calibrate and adjust the effect wheels to their correct positions. The password

of calibrate values is 050.

USERS MODE SET

In this menu, user can select different channels list by different sequence:

For example, after the user enter this manual, if select Auto Program = CH 22, means in this User’s mode,

the “Dimmer” is in Channel 16.

User mode

With this function, you can create user defined channel orders.

Preset User mode

With this function, you can adjust the rest user defined channel order.

EDIT PROGRAM

Select program

With this function, you can select the program for the Program Run.

Edit program

With this function, you can edit the internal programs.

Edit scenes

With this function, you can edit the scenes of the internal programs.

Auto scenes rec.

The moving head features an integrated DMX-recorder by which you can transmit the programmed scenes

from your DMX-controller to the moving head. Adjust the desired scene numbers via the encoder (from –

GB SGM

Idea Spot 700 XM473-V1.0-NR

１７

to). When you call up the scenes at your controller, they will automatically be transmitted to the moving

head.

Excursion:

A Master unit can send up to 3 different data groups to the Slave units, i.e. a Master unit can start 3

different Slave units, which run 3 different programs. The Master unit sends the 3 program parts in a

continuous loop.

The Slave unit receives data from the Master unit according to the group which the Slave unit was assigned

to. If e.g. a Slave unit is set to “Slave 1” in the menu “Set to Slave”, the Master unit sends “Auto Program

Part 1” to the Slave unit. If set to “Slave 2”, the Slave unit receives “Auto Program Part 2”.

To start a Auto Program please proceed as follows:

1. Slave-Setting

 Select “Function Mode” by turning the encoder.

 Press the Enter button to confirm.

 Select “Set to slave” by turning the encoder.

 Press the Enter button to confirm.

 Turn the encoder to select “Slave 1”, “Slave 2” or “Slave 3”.

 Press the Enter button to confirm.

 Press the Mode/Esc button in order to return to the main menu.

2. Automatic Program Run

 Select “Function Mode” by turning the encoder.

 Press the Enter button to confirm.

 Select “Auto Program” by turning the encoder.

 Press the Enter button to confirm.

 Turn the encoder to select “Master” or “Alone”. The selection "Alone" means Stand Alone-mode and

"Master" that the device is defined as master.

 Press the Enter button to confirm.

 Press the Mode/Esc button in order to return to the main menu.

3. Program selection for Auto Pro Part

 Select “Edit program” by turning the encoder.

 Press the Enter button to confirm.

 Select “Select programs” by turning the encoder.

 Press the Enter button to confirm.

 Turn the encoder to select “Auto Pro Part 1”, “Auto Pro Part 2” or “Auto Pro Part 3”, and thus select

which Slave program is to be sent. Selection “Part 1” means, that the Slave unit runs the same program

as the master units.

 Press the Enter button to confirm.

 Press the Mode/Esc button in order to return to the main menu.

4. Program selection for Edit Program

 Select “Edit program” by turning the encoder.

 Press the Enter button to confirm.

 Select “Edit program” by turning the encoder.

 Press the Enter button to confirm.

 Turn the encoder to select the desired program. With this function you can edit specific scenes into a

specific program.

 Press the Enter button to confirm.

 Press the Mode/Esc button in order to return to the main menu.

SGM GB

XM473-V1.0-NR Idea Spot 700

１８

5. Automatic Scene Recording

 Select “Edit program” by turning the encoder.

 Press the Enter button to confirm.

 Select “Edit scenes” by turning the encoder.

 Turn the encoder to select the desired scene numbers. You can program a maximum number of 250

scenes.

 Press the Enter button to confirm.

 Press the Mode/Esc button in order to return to the main menu.

Example:

Program 2 includes scenes: 10, 11, 12, 13

Program 4 includes scenes: 8, 9, 10

Program 6 includes scenes: 12, 13, 14, 15, 16

Auto Pro Part 1 is Program 2;

Auto Pro Part 2 is Program 3;

Auto Pro Part 3 is Program 6

The 3 Slave groups run the Auto Program in certain time segments, as shown in the following picture:

La pagina sta caricando ...

SGM IDEA SPOT 700 Manuale utente

Marca: SGM

Modello: IDEA SPOT 700

Categoria: Macchina per la riduzione del rumore

Tipo: Manuale utente

Scarica il pdf

rapporto

in altre lingue

English: SGM IDEA SPOT 700 User manual

SGM IDEA SPOT 700 Manuale utente

SGM IDEA SPOT 700 Manuale utente

in altre lingue

Documenti correlati

Altri documenti