ProLights 7x15W moving LED wash Manuale utente

USER MANUAL

MANUALE UTENTE

DIAMOND7

MOVING HEAD

EN - IT

reproduced in any form or by any means for any commercial use.

In order to improve the quality of products, Music&Lights S.r.l. reserves the right to modify the

characteristics stated in this instruction manual at any time and without prior notice.

All revisions and updates are available in the ‘manuals’ section on site www.musiclights.it

REV. 05-11/18

1

DIAMOND7

Packing content

• DIAMOND7

• Mount bracket

• User manual

TABLE OF CONTENTS

Safety

General instructions

Warnings and installation precautions

1 Introduction

1. 1 Description

1. 2 Technical specications

1. 3 Operating elements and connections

2 Installation

2. 1 Mounting

3 Functions and settings

3. 1 Operation

3. 2 Basic

3. 3 Menu structure

3. 4 Slave Receive mode

3. 5 Operation in automatic mode

3. 6 Scenes Record mode

3. 7 Music mode

3. 8 Sensitivity microphone

3. 9 Linking

3. 10 DMX mode

3. 11 DMX conguration

3. 12 DMX addressing

3. 13 Connection of the DMX line

3. 14 Construction of the DMX termination

3. 15 DMX control

3. 16 Wireless control settings

3. 17 Fixture settings

3. 18 Lamp settings

3. 19 Display settings

3. 20 Fixture information

3. 21 Reset functions

3. 22 Special functions

4 Maintenance

4. 1 Maintenance and cleaning the unit

4. 2 Fuse replacement

4. 3 Trouble shooting

2

3

6

7

8

9

11

12

13

14

15

16

17

22

23

24

27

28

DIAMOND7

2

WARNING! Before carrying out any operations with the unit, carefully read this instruction

manual and keep it with cure for future reference. It contains important information about

the installation, usage and maintenance of the unit.

SAFETY

General instruction

• The products referred to in this manual conform to the European Community Directives and are there-

fore marked with .

• The unit is supplied with hazardous network voltage (230V~). Leave servicing to skilled personnel only.

Never make any modications on the unit not described in this instruction manual, otherwise you will

risk an electric shock.

• Connection must be made to a power supply system tted with ecient earthing (Class I appliance ac-

cording to standard EN 60598-1). It is, moreover, recommended to protect the supply lines of the units

from indirect contact and/or shorting to earth by using appropriately sized residual current devices.

• The connection to the main network of electric distribution must be carried out by a qualied electrical

installer. Check that the main frequency and voltage correspond to those for which the unit is designed

as given on the electrical data label.

• This unit is not for home use, only professional applications.

• Never use the xture under the following conditions:

- in places wet;

- in places subject to vibrations or bumps;

- in places with an ambient temperature of over 45°C.

• Make certain that no inammable liquids, water or metal objects enter the xture.

• Do not dismantle or modify the xture.

• All work must always be carried out by qualied technical personnel. Contact the nearest sales point for

an inspection or contact the manufacturer directly.

• If the unit is to be put out of operation denitively, take it to a local recycling

plant for a disposal which is not harmful to the environment.

Warnings and installation precautions

• If this device will be operated in any way dierent to the one described in this manual, it may suer

damage and the guarantee becomes void. Furthermore, any other operation may lead to dangers like

short circuit, burns, electric shock, etc.

• Before starting any maintenance work or cleaning the projector, cut o power from the main supply.

• Always additionally secure the projector with the safety rope. When carrying out any work, always com-

ply scrupulously with all the regulations (particularly regarding safety) currently in force in the country

in which the xture’s being used.

• For inside use only. Not designed for outside use.

• The minimum distance between the xture and surrounding walls must be more than 50 cm and the

air vents at the housing must not be covered in any case.

• Install the xture in a well ventilated place.

• Keep any inammable material at a safe distance from the xture.

• The maximum temperature that can be reached on the external surface of the tting, in a thermally

steady state, is high. After power o, please cool down over 15 minutes.

• Shields, lenses or ultraviolet screens shall be changed if they have become damaged to such an extent

that their eectiveness is impaired.

• The lamp (LED) shall be changed if it has become damaged or thermally deformed.

• Never look directly at the light beam. Please note that fast changes in lighting, e. g. ashing light, may

trigger epileptic seizures in photosensitive persons or persons with epilepsy.

3

DIAMOND7

- 1 - INTRODUCTION

1.1 DESCRIPTION

DIAMOND7 is the most compact xture of the stunning DIAMOND LED pixel wash family. As a wash light,

the 6-66° zoom, even beam and fantastic colour range create a true workhorse xture. For the next level,

individual control of each LED pixel, tied with the DIAMOND’s clever optical design and its onboard eects

provides ‘eye candy’ eects both to look at and in the air.

Compact, consistent and clever, the DIAMOND7 makes a statement, even when space is an issue.

1.2 TECHNICAL SPECIFICATIONS

LIGHT SOURCE

• Source: 7x15W RGBW Osram Ostar LEDs

• Lux: (6°) 10980 - (66°) 745lux @3m full

• Source life expectancy: >50.000 h

OPTICS

• Zoom: 6-66° motorised linear zoom

• Lens diameter: 126mm

• Lens type: honeycomb gapless plano-convex optics

COLOUR SYSTEM

• Colour mixing: RGBW/FC

• CTC: CTC control through independent DMX channel

• White presets: 2000~10000K

• Colour wheel: virtual colour wheel with presets

DYNAMIC EFFECTS

• Pixel patterns: pre-programmed dynamic and static patterns

• FX generator: adjustable foreground/background colour, index, speed, direction

BODY

• Pan angle: 630°

• Tilt angle: 265°

• Pan/Tilt resolution: 8/16 bit

• Feedback: automatic repositioning after accidental movement

• Body: aluminium structure with hi-resistance polycarbonate cover

• Body colour: black, white nishing available

CONTROL

• Protocols: DMX512, RDM

• DMX channels: 19 / 26 / 50 / 18 / 20channel

• Pixel control: pixel2pixel control

• W-DMX: optional, wireless solution receiver

• RDM: RDM ready for xture remote monitor and settings

• Display: LCD high resolution colour display

• Firmware upgrade: yes, via USB-DMX interface (UPBOX2) not included

• Hibernation: power safe mode when lost DMX

DIAMOND7

4

• Master/Slave: for synchronized operation of more units linked in a chain

ELECTRONICS

• Dimmer: linear 0~100% electronic dimmer

• Strobe / shutter: 1-25 Hz, electronic

• Battery backup: battery backup for user operation without connecting to the main power

• Operating temperature: -10° ~ +45°

• Flicker: icker free operation

ELECTRICAL

• Power supply: 100-240V – 50/60Hz

• Power consumption (at 230V): 125W

• Power consumption (at 120V): 125W

• Output (at 230V): 12 units on a single power line

PHYSICAL

• Cooling: combination of heat pipe cooling system and low noise fan

• Sospension and xing: any position with quick-lock omega brackets

• Signal connection: Amphenol XLR 3p + 5p IN/OUT connectors

• Power connection: Neutrik powerCON IN/OUT connectors

• IP rating: 20

• Dimensions (WxHxD): 278x348x200mm

• Weight: 6.4kg

5

DIAMOND7

Fig.1

Photometric data

Technical drawing

200mm

7,87in

278mm

10,94in

348mm

13.7in

Illuminance at a Distance

6°- 66°

3m

5.0m

7.5m

0m

0.44/3.95m

0.65/6.50m

Lux Center Beam Angle: 6°- 66° Beam Width

9700/745lx

3263/302lx

0.91/9.68m

1494/141lx

DIAMOND7

6

1. MOVING HEAD

2. ROTARY ARM

3. HANDLE

4. LED INDICATOR "WDMX"

5. MICROPHONE

6. CONTROL PANEL with LCD display

and 5 button used to access

the control panel functions and

manage them.

7. DMX OUT ( 3-pole XLR):

1 = ground, 2 = DMX -, 3 = DMX +

8. DMX IN (3-pole XLR):

1 = ground, 2 = DMX -, 3 = DMX +

9. DMX OUT (5-pole XLR):

1 = ground, 2 = DMX-, 3 = DMX+,

4 N/C, 5 N/C

10. DMX IN (5-pole XLR):

1 = ground, 2 = DMX-, 3 = DMX+,

4 N/C, 5 N/C

11. POWER IN (PowerCON IN):

for connection to a socket

(100-240V~/50-60Hz) via the

supplied mains cable.

12. POWER OUT (PowerCON OUT):

power output for connection of

multiple units in series.

13. MAIN FUSE HOLDER: replace a

burnt-out fuse by one of the same

type only.

1.3 OPERATING ELEMENTS AND CONNECTIONS

Fig.2

View A

View B

4

A

B

1

2

3

5 6

7 9 11 12

8 10 13

7

DIAMOND7

- 2 - INSTALLATION

2.1 MOUNTING

The DIAMOND7 may be set up on a solid and even surface. By means of the xing facilities of the base-

plate, the unit can also be mounted upside down to a cross arm. The base plate is shown in g.3. For xing,

stable mounting clips are required. According to the gure, the bolts of the brackets are placed into the

openings provided in the base plate and turned clockwise until they lock (to the stop). Always ensure that

the unit is rmly xed to avoid vibration and slipping while operating. The mounting place must be of

sucient stability and be able to support a weight of 10 times of the unit’s weight. When carrying out any

installation, always comply scrupulously with all the regulations (particularly regarding safety) currently

in force in the country in which the xture’s being used. Always additionally secure the projector with the

safety rope from falling down. For this purpose, fasten the safety rope at a suitable position so that the

maximum fall of the projector will be 20 cm.

Fig.3

CLAMP

SAFETY

CABLE

OMEGA

BRACKETS

DIAMOND7

8

- 3 - FUNCTIONS AND SETTINGS

3.1 OPERATION

Connect the supplied main cable to a socket (100-240V~/50-60Hz). The unit will run built-in program to

reset all motors to their home position. Shortly after that the DIAMOND7 is ready for operation. To switch

o, disconnect the mains plug from the socket. For a more convenient operation it is recommended to

connect the unit to a socket which can be switched on and o via light switch.

3.2 BASIC

The DIAMOND7 has a LCD display and 5 button used to access the control panel functions and manage

them (g.4).

Fig.4 - Functions of the buttons and display icons

CONNECT

LIGHT

INFORMATION

SET

PROGRAM

LEFT RIGHT UP DOWN ENTER BATTERY

Return to the top

level

Commute from

units, tens, hundred

in the menu

Increases the value

displayed or passes

to the previous item

in a menu

Decreases the value

displayed or passes

to the next item in

the menu

Conrms the

displayed value,

or activates the

displayed function,

or enters the

successive menu

Used to activate the

backup battery. It

allows to switching

display interface

without main power

Battery

9

DIAMOND7

3.3 MENU STRUCTURE

MENU

1 Connect

ð

DMX Address

ð

Value (1-512)

Wireless DMX

ð

Value (1-512)

2 Light

ð

Max Temperature

ð

Value (60°-130° C)

Lamp Adjust

ð

Control

ð

Value (000-255)

Pan

ð

Value (000-255)

Pan Fine

ð

Value (000-255)

Tilt

ð

Value (000-255)

Tilt Fine

ð

Value (000-255)

Pan&Tilt Speed

ð

Value (000-255)

Pan&Tilt Fun

ð

Value (000-255)

Shutter Fun

ð

Value (000-255)

Shutter

ð

Value (000-255)

Dimmer

ð

Value (000-255)

Color Function

ð

Value (000-255)

Virtual Color1

ð

Value (000-255)

Virtual Color2

ð

Value (000-255)

Red-All

ð

Value (000-255)

Green-All

ð

Value (000-255)

Blue-All

ð

Value (000-255)

White-All

ð

Value (000-255)

Zoom

ð

Value (000-255)

Pattern

ð

Value (000-255)

Pattern Speed

ð

Value (000-255)

Pattern Byte 1

ð

Value (000-255)

Pattern Byte 2

ð

Value (000-255)

Pattern Byte 3

ð

Value (000-255)

Pattern Byte 4

ð

Value (000-255)

Fade Time

ð

Value (000-255)

Scene Time

ð

Value (000-255)

3 Information

ð

Time Info.

Temperature

Fans Speed

Channel Value

Error Message

DIAMOND7

10

Fixture Model

Software Ver.

4 Set

ð

Reset

ð

All

Pan & Tilt

Others

Movement

ð

Pan Reverse

ð

ON/OFF

Tilt Reverse

ð

ON/OFF

Pan Degree

ð

540/630

Encoders

ð

ON/OFF

Pan/Tilt Mode

ð

Standard/Smooth

UI Set

ð

Mic Sens.

ð

Value (00-99%)

No Signal

ð

Close/Hold/Auto/Music

Temperature C/F

ð

Celsius/Fahrenheit

Fans Mode

ð

Auto Speed/High Speed

Zoom Mode

ð

Mode1 /Mode2

Hibernation

ð

Not Hibernation/Min (01-99)

Backlight

ð

Always On/Min (01-99)

Flip Display

ð

ON/OFF

Display Bright

ð

Value (00-31)

Brand Show

ð

ON/OFF

Key Lock

ð

ON/OFF

Language

ð

EN/FR/SP...

Fixture Set

ð

Theater Mode

ð

ON/OFF

Frequency

ð

600/1200/2000/2400/4000 Hz/25 kHz

Users

ð

User Mode

ð

Standard/Extended1/Extended2/Basic-8bit/...

Edit User

ð

Max Channel/Control/Pan/Pan Fine/Tilt/Tilt Fine...

Calibration

ð

Password

ð

050 (insert to unlock the following settings)

Pan

ð

Value (-128-127)

Tilt

ð

Value (-128-127)

Fixture ID

ð

Name

ð

Fixture ID Name

RDM Mode

Password

ð

050 (insert to unlock the following settings)

PID Code

ð

00001

Wireless Set

ð

DMX On Cable

ð

ON/OFF

Reset Connect

ð

ON/OFF

Reload Default

ð

Basic Reload

ð

ON/OFF

Program Reload

ð

ON/OFF

11

DIAMOND7

3.4 SLAVE RECEIVE MODE

This mode will allow you to link up the units together without a controller. Choose a unit to function as the

Master. The unit must be the rst unit in line; other units will work as slave with the same eect.

A Master unit can send up to 3 dierent data groups to the Slave units, i.e. a Master unit can start 3 dier-

ent Slave units, which run 3 dierent programs. The Master unit sends the 3 program parts in a continuous

loop.

The Slave unit receives data from the Master unit according to the group which the Slave unit was as-

signed to.

For example, if a slave device is set to Receive Part 1, the Master unit Slave unit will send the automated

Chase Part 1; if set to Receive Part 2, the Chase Part 2 Slave units will receive from the Master.

To set the drive as a slave, proceed as follows:

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select the Program icon, then press the ENTER button to

enter the next menu.

• Press the UP/DOWN button to scroll through the menu, and then select Play and press the ENTER

button to enter the next menu.

• Press the UP/DOWN button to scroll through the menu, and select Slave Receive and press ENTER to

conrm.

• Press the UP/DOWN button to select the dierent modes of operation Part 1 Receive/Receive Part 2/Part 3

Receive, and then press the ENTER button to conrm your choice.

• Press the LEFT button repeatedly to exit the menu and save changes.

Password

ð

050 (insert to unlock the following settings)

Private Reload

ð

ON/OFF

All Reload

ð

ON/OFF

5 Program

ð

Play

ð

DMX Receive

Slave Receive

ð

Part 1 Receive/Part 2 Receive/Part 3 Receive

Sequence

ð

Alone/Master

Music

ð

Alone/Master

Select Chase

ð

Chase Part 1

ð

Chase 1 - Chase 8

Chase Part 2

ð

Chase 1 - Chase 8

Chase Part 3

ð

Chase 1 - Chase 8

Edit Chases

ð

Edit Chase 1

ð

Chase Test/ Step 1 - Step 64

Edit Chase 2

ð

Chase Test/ Step 1 - Step 64

Edit Chase ...

ð

Chase Test/ Step 1 - Step 64

Edit Chase 8

ð

Chase Test/ Step 1 - Step 64

Edit Scenes

ð

Edit Scenes 001

ð

Control/.../Fade Time/Scene Time/External Input

Edit Scenes 002

ð

Control/Pan/Pan Fine/Tilt/Tilt Fine...

Edit Scenes ...

ð

Control/Pan/Pan Fine/Tilt/Tilt Fine...

Edit Scenes 250

ð

Control/Pan/Pan Fine/Tilt/Tilt Fine...

Scenes Record

ð

Sc XX - Sc XX

DIAMOND7

12

Select the desired program on the master unit (described in section 3.5).

Use the DMX connectors of the DIAMOND7 and an XLR cable to form a chain of units. Under certain

conditions and lengths you want to make a termination as shown on page 17.

3.5 OPERATIONS IN AUTOMATIC MODE

The unit independently runs through its show. Before you send an automatic program you need to set the

drive as Master/Alone:

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select the Program icon, then press the ENTER button to

enter the next menu.

• Press the UP/DOWN button to scroll through the menu, select Play and press the ENTER button to enter

the next menu.

• Press the UP/DOWN button to scroll through the menu, select Sequence and press ENTER to conrm

your choice.

• Press the UP/DOWN button to select the mode of operation:

- Master, if the unit is connected in series with other units and it acts as the Master;

- Alone, if the unit is not connected to other units.

• Press the ENTER button to conrm your choice.

• Press the LEFT button repeatedly to exit the menu and save changes.

The unit will go into automatic mode by executing the program automatically.

Select Chase

The function Select Chase lets you choose the automatic program to actually run.

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select the Program icon, then press the ENTER button to

enter the next menu.

• Press the UP/DOWN button to scroll through the menu, select Select Chase and press the ENTER button

to enter the next menu.

• Press the UP/DOWN button to scroll through the menu, then select Chase Part 1/Chase Part 2/Chase Part 3

and press ENTER to conrm.

• Press the UP/DOWN button to select Chase1-Chase8, and press the ENTER button to conrm.

• Press the LEFT button repeatedly to exit the menu and save changes.

Edit Chases

The function Edit Chases allows you to create automatic pre-programmed show.

The automatic programs Chase Part1/2/3 are each divided into Chase1-Chase8. Each Chase can be composed

of 1-64 step that can be congured through the following procedure:

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select the Program icon, then press the ENTER button to

enter the next menu.

• Press the UP/DOWN button to scroll through the menu, select Edit Chases and press the ENTER button

to enter the next menu.

• Press the UP/DOWN button to scroll through the menu, select Edit Chase 1 - Edit Chase 8, then press the

ENTER button to conrm.

• Press the UP/DOWN button to select the Step 01 - Step 64, and press ENTER to conrm.

• Press the UP/DOWN button to select the Scene you want to set for the Step chosen, and then press

ENTER to conrm.

• Press the LEFT button repeatedly to exit the menu and save changes.

13

DIAMOND7

Edit Scenes

The function Edit Scenes allows you to create individual scenes to be included in the Chase Step.

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select the Program icon, then press the ENTER button to

enter the next menu.

• Press the UP/DOWN button to scroll through the menu, select Edit Scenes and press the ENTER button

to enter the next menu.

• Press the UP/DOWN button to scroll through the menu, select Edit Scene 001 - Edit Scene 250, then press the

ENTER button to conrm.

• Press the UP/DOWN button to select the desired function you want to edit (Control, Pan, Tilt, etc..), Then

press the ENTER button to conrm.

• Press the UP/DOWN button to change the value of the function, then press the ENTER button to

conrm. Press the LEFT button repeatedly to exit the menu and save changes.

3.6 SCENES RECORD MODE

DIAMOND7 is equipped with a built-in DMX recorder by which you can transmit the programmed scenes

from your DMX-controller to the device. Proceed as follows to store the sequence of scenes in the unit.

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll through the menu, select the Program icon, then press the ENTER

button to enter the next menu.

• Press the UP/DOWN button to scroll through the menu, select Scenes Record and press the ENTER button

to enter the next menu.

• Press the UP/DOWN button to adjust the scene at the beginning and end to be inserted in the auto-

matic program, then press the ENTER button to conrm.

• Press the LEFT button repeatedly to exit the menu and save changes.

When recalling scenes from the controller will automatically be transmitted to the device.

3.7 MUSIC MODE

In music mode, via its integrated microphone, the unit can be controlled by music with a clear rhythm in

the bass range. If the music control should not work optimally, increase the volume or reduce the distance

between the sound source and the light eect unit or alternatively increase the sensitivity of the micro-

phone.

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select the Program icon, then press the ENTER button to

enter the next menu.

• Press the UP/DOWN button to scroll through the menu, select Play and press the ENTER button to enter

the next menu.

• Press the UP/DOWN button to scroll through the menu, select Music and press ENTER to conrm.

• Press the UP/DOWN button to select the mode of operation:

- Master, if the mobile head is connected in series to other units, and it performs the Master function;

- Alone, if the xture is not connected to other units.

• Press the ENTER button to conrm your choice.

• Press the LEFT button repeatedly to exit the menu and save changes.

The unit will go into music mode by executing an automatic program to the rhythm of music.

3.8 SENSITIVITY MICROPHONE

Select this function to set the value of the sensitivity of the microphone for use with a music control:

DIAMOND7

14

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select the Set icon, then press the ENTER button to enter

the next menu.

• Press the UP/DOWN button to scroll through the menu, select UI Set, and press the ENTER button to

enter the next menu.

• Press the UP/DOWN button to scroll through the menu, then select Mic Sens. and press ENTER to conrm.

• Press the UP/DOWN button to adjust the level of sensitivity of the microphone, and then press the

ENTER button to conrm your choice.

• Press the LEFT button repeatedly to exit the menu and save changes.

3.9 LINKING

Several units may be interconnected in order to control all further slave units to the same eect of the

master unit.

1. Connect the DMX OUT of the master unit via 3/5-pole XLR cable to the DMX IN of the rst slave unit.

2. Connect the DMX OUT of the rst slave unit to the DMX IN of the second slave unit, etc. until all units

are connected in a chain.

3.10 DMX MODE

To enter the DMX mode, follow these steps:

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select the Connect icon, then press the ENTER button to

enter the next menu.

• Press the UP/DOWN button to scroll through the menu, select the DMX Address and press the ENTER key.

• Press the arrow keys to select the desired value (001-512).

• Press the ENTER key to conrm the setting.

• Press the LEFT button repeatedly to exit the menu and save changes.

3.11 DMX CONFIGURATION

The DIAMOND7 has 5 DMX channel congurations which can be accessed from the control panel.

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select the Set icon, then press the ENTER button to enter

the next menu.

• Press the UP/DOWN button to scroll through the menu, select Users and press the ENTER button to

enter the next menu.

• Press the UP/DOWN button to scroll through the menu, select User Mode and press ENTER to conrm

your choice.

• Use the UP/DOWN button to select the desired DMX channel conguration (Standard, Extended1,

Extended2, Basic-8bit, Basic-16bit, User), then press the ENTER button to conrm your choice.

• Press the LEFT button repeatedly to exit the menu and save changes.

The tables on page 18 show the mode of operation and their values DMX.

The unit is equipped with 3/5-pole XLR connections.

Edit User

The Edit User, in the same menu, allows you to create a prole of personalized functions. You can change

the parameters of the various functions (Control, Pan, Tilt, etc.). Once you’ve created your custom prole,

you can use it by selecting the USER mode as described above.

15

DIAMOND7

Number of

DMX channels

Start address

(example)

DMX Address

occupied

Next possible start

address for unit No. 1

Next possible start

address for unit No. 2

Next possible start

address for unit No. 3

19 33 33-51 52 71 90

26 33 33-58 59 85 111

50 33 33-82 83 133 183

18 33 33-50 51 69 87

20 33 33-52 53 73 93

3.12 DMX ADDRESSING

For operation via light control unit with DMX512 protocol, is sucient connect the controller to DIA-

MOND7. To able to operate the DIAMOND7 with a light controller, adjust the DMX start address for the

rst a DMX channel. If e. g. address 33 on the controller is provided for controlling the function of the rst

DMX channel, adjust the start address 33 on the DIAMOND7. The other functions of the light eect panel

are then automatically assigned to the following addresses.

An example with the start address 33 is shown below:

Fig.5 - Example 19 DMX channels conguration

DMX Address: 90DMX Address: 52DMX Address: 33 DMX Address: 71

. . . . . . . . . . . .

DMX512 Controller

DIAMOND7

16

Fig.6

Fig.7

3.13 CONNECTION OF THE DMX LINE

DMX connection employs standard XLR connectors. Use shielded pair-twisted cables with 120Ω imped-

ance and low capacity.

The following diagram shows the connection mode:

ATTENTION

The screened parts of the cable (sleeve) must never be connected to the system’s earth, as this would

cause faulty xture and controller operation.

Over long runs can be necessary to insert a DMX level matching amplier.

For those connections the use of balanced microphone cable is not recommended because it cannot

transmit control DMX data reliably.

• Connect the controller DMX input to the DMX output of the rst unit.

• Connect the DMX output to the DMX input of the following unit. Connect again the output to the input

of the following unit until all the units are connected in chain.

• When the signal cable has to run longer distance is recommended to insert a DMX termination on the

last unit.

3.14 CONSTRUCTION OF THE DMX TERMINATION

The termination avoids the risk of DMX 512 signals being reected back along the cable when they reach-

es the end of the line: under certain conditions and with certain cable lengths, this could cause them to

cancel the original signals.

The termination is prepared by soldering a 120Ω 1/4 W resistor between pins 2 and 3 of the 5-pin male XLR

connector, as shown in gure.

DMX - OUTPUT

XLR socket

DMX - INPUT

XLR plug

Pin1 : GND - Shield

Pin2 : - Negative

Pin3 : + Positive

Pin4 : N/C

Pin5 : N/C

Example:

3 pin XLR connector

17

DIAMOND7

3.15 DMX CONTROL

STAND EXT-1 EXT-2 BAS-8 BAS-16

FUNCTION DMX

Value

19 Ch 26 Ch 50Ch 18 Ch 20 Ch

1 1 1 1 1

PAN

0~100% 000 - 255

2 2 2

PAN FINE

0~100% 000 - 255

2 3 3 2 3

TILT

0~100% 000 - 255

4 4 4

TILT FINE

0~100% 000 - 255

3 5 5 3 5

MOVEMENT SPEED

Fast to slow 000 - 255

6 6

MOVEMENT FUNCTION

Normal

Movement with backout

TBD

000 - 015

016 - 031

032 - 255

4 7 7

SHUTTER FUNCTION

Normal Shutter Functions

Pulse-eect Forward

Pulse-eect Reverse

Random strobe

TBD

000 - 015

016 - 031

032 - 047

048 - 063

064 - 255

5 8 8

SHUTTER

Normal Shutter Functions

Close

Strobe Rate (slow to fast)

Open

Pulse-eect Forward

Close

Strobe Rate (slow to fast)

Open

Pulse-eect Reverse

Close

Strobe Rate (slow to fast)

Open

Random Strobe

Close

Strobe Rate (slow to fast)

Open

000 - 031

032 - 223

224 - 255

000 - 031

032 - 223

224 - 255

000 - 031

032 - 223

224 - 255

000 - 031

032 - 223

224 - 255

4 6

SHUTTER

Shutter closed

No function (shutter open)

Strobe eect slow to fast

000 - 031

032 - 063

064 - 095

DIAMOND7

18

STAND EXT-1 EXT-2 BAS-8 BAS-16

FUNCTION DMX

Value

19 Ch 26 Ch 50 Ch 18 Ch 20 Ch

4 6

No function (shutter open)

Pulse-eect in sequences

No function (shutter open)

Random strobe eect slow to fast

No function (shutter open)

096 - 127

128 - 159

160 - 191

192 - 223

224 - 255

6 9 9 5 7

DIMMER

Dimmer (close to open) 000 - 255

7 10 10 6 8

VIRTUAL COLOR FUNCTION

On Function

CTC Function

Forward Spin

Reverse Spin

Continuous

Color Bounce

TBD

000 - 015

016 - 031

032 - 047

048 - 063

064 - 079

080 - 111

112 - 255

8 11 11 7 9

VIRTUAL COLOR 1

CTC Function

Color Temperature Correction 2000K->2700K

White 3200K

White 4200K

White 5600K

White 8000K

Forward Spin

Rainbow Eect (Slow to Fast)

Reverse Spin

Rainbow Eect (Slow to Fast)

Continuous & Color Bounce

Black

Red

Green

Blue

White

Red=0, Green->up, Blue=full, White=0

Red=0, Green=full, Blue->down, White=0

Red->up, Green=full, Blue=0, White=0

Red=full, Green->down, Blue=0, White=0

Red=full, Green=0, Blue->up, White=0

Red->down, Green=0, Blue=full, White=0

000 - 223

224 - 231

232 - 239

240 - 247

248 - 255

000 - 255

000 - 000

001 - 001

002 - 002

003 - 003

004 - 004

005 - 046

047 - 088

089 - 130

131 - 172

173 - 214

215 - 255

9 12 12 8 10

VIRTUAL COLOR 2 (Only on Color Bounce)

Color Bounce

Black

Red

000 - 000

001 - 001

La pagina si sta caricando...

ProLights 7x15W moving LED wash Manuale utente

ProLights 7x15W moving LED wash Manuale utente

in altre lingue

Documenti correlati

Altri documenti