Simplicity 1696211-00 Manuale utente

Tipo
Manuale utente

Questo manuale è adatto anche per

Single Stage Snowthrower
Model No. Description
1695886 Single Stage Snowthrower, 8.00 TP / 22 Inch (55,9 cm)
1696211-00 Single Stage Snowthrower, 8.00 TP / 22 Inch (55,9 cm)
1750858
Revision B
Operator’s Manual
Návod k obsluze
Bedienungsanleitung
Ohjekirja
Manual de l’opérateur
Felhasználói kézikönyv
Manuale per l’operatore
Vartotojo vadovas
Bruksanvisning
Instrukcja obsługi
Руководство по
эксплуатации
Uporabniški priročnik
Handbok
en
de
fr
hu
cs
fi
it
no
sl
sv
lt
pl
ru
Not for Reproduction
2
3
A
4
5
A
C
B
A
BC A
D
E
F
G
6
7
8
A
Not for Reproduction
3
en
A
A
B
B
9 10
A
B
11
12
Not for Reproduction
4
C
B
A
14
D
C
13
E
Not for Reproduction
5
en
Table of Contents
Illustrations .......................................................................................2
Operator Safety ................................................................................6
Features and Controls ...................................................................12
Operation ........................................................................................13
Maintenance ...................................................................................17
Storage ............................................................................................19
Troubleshooting .............................................................................20
Warranty ..........................................................................................21
Speci cations .................................................................................22
General Information
Thank you for purchasing this quality-built MURRAY snowthrower. We’re pleased that you’ve placed your confidence in our brand.
When operated and maintained according to the instructions in this manual, your MURRAY product will provide many years of
dependable service.
This manual contains safety information to make you aware of the hazards and risks associated with snowthrowers and how to
avoid them. This snowthrower is designed and intended only for snow removal and is not intended for any other purpose. It is
important that you read and understand these instructions thoroughly before attempting to start or operate this equipment. Save
these instructions for future reference.
Table of Contents
Product Reference Data
When contacting your authorized dealer for replacement
parts, service, or information you MUST have these
numbers.
Record your model name/number, manufacturer’s
identification numbers, and engine serial numbers in the
space provided for easy access.
PRODUCT REFERENCE
Model Description Name/Number
Unit Serial Number
Dealer Name Date Purchased
ENGINE REFERENCE DATA
Engine Make Engine Model
Engine Type/Spec Engine Code/Serial Number
C
B
A
D
E
F
G
H
I
MODEL NO. xxxxxxx
SERIAL NO. xxxxxxxxxx
20xx
x.x kW
xxxx min
-1
xxx
dB
xxx kg
XXXXXXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXX
A. Manufacturer’s Identification Number
B. Manufacturer’s Serial Number
C. Manufacturer’s Name and Address
D. Maximum Engine Speed in Rotations per Minute
E. Power Rating in Kilowatts
F. Mass of Unit in Kilograms
G. CE Compliance Logo
H. Year of Manufacture
I. Guaranteed Sound Power in Decibels
The Illustrated Parts List for this machine can be downloaded from www.murray.com. Please provide model and serial number when
ordering replacement parts.
Copyright © 2012 Briggs & Stratton Power Products Group, LLC
Milwaukee, WI, All rights reserved.
MURRAY is a trademark of Briggs & Stratton Power Products Group, LLC Milwaukee, WI USA
CE Identi cation Tag
Vibration measurement uncertainty – machine vibration
was recorded using methods and procedures outlined in the
appropriate International Standards in e ect at the time of
manufacturer. The uncertainties due to the measurement
may result in a variance of up to 5% from the published value
shown in the Declaration of Conformity.
Not for Reproduction
6
Operator Safety
On / O Key Switch.
Turn Choke Closed to Start.
Turn Choke Open to Run.
Push Primer 2 Times.
Plug in Extension Cord.
Push Button to Start.
Engage Auger.
Chute Rotation.
Cold Engine.
Hot Engine.
Read the Operator’s Manual for oper-
ating and safety instructions.
Shuto engine and remove key
before performing maintenance and
repair work.
Thrown Objects Hazard.
Fire Hazard.
Amputation Hazard - rotating auger.
Carbon Monoxide Poisoning Hazard.
Keep Safe Distance.
Electric Shock.
Amputation Hazard - rotating
impeller.
Keep Children Away.
Amputation Hazard - rotating
impeller.
Amputation Hazard - do not touch
moving parts.
Hot Surface Hazard.
Hazard Symbols and Meanings Control Symbols on Equipment
Not for Reproduction
7
en
Operator Safety
Safety Alert Symbol and Signal Words
The safety alert symbol and signal word (DANGER, WARN-
ING, CAUTION, or NOTICE) is used to indicate the likelihood and
potential severity of personal injury and/or damage to the product.
In addition, a hazard symbol may be used to represent the type of
hazard.
DANGER indicates a hazard which, if not avoided,
will result in death or serious injury.
WARNING indicates a hazard which, if not avoided,
could result in death or serious injury.
CAUTION indicates a hazard which, if not avoided,
could result in minor or moderate injury.
NOTICE indicates a situation that could result in
damage to the product.
WARNING
Certain components in this product and its related accessories
contain chemicals known to the State of California to cause
cancer, birth defects, or other reproductive harm. Wash hands
after handling.
WARNING
The engine exhaust from this product contains chemicals
known to the State of California to cause cancer, birth defects,
or other reproductive harm.
WARNING
Hand contact with the rotating impeller inside the discharge
chute is the most common cause of injury associated with
snowthrowers.
This snowthrower is capable of amputating hands and
feet, and throwing objects. Read and observe all the safety
instructions in this manual. Failure to do so could result in
death or serious injury.
WARNING
Read, understand, and follow all the instruc-
tions on the snowthrower and in the operator’s
manual before operating this unit.
Failure to observe the safet y instructions in this
manual could result in death or serious injury.
Be thoroughly familiar with the controls and the proper use of
the snowthrower.
Make sure you are properly trained before operating the
snowthrower.
Know how to stop the unit and disengage the controls
quickly.
Never allow anyone to operate the snowthrower without
proper instruction.
Always follow the instructions in the operator’s manual, if the
snowthrower will be stored for an extended period.
Maintain or replace safety and instruction labels as
necessary.
Never attempt to make major repairs on the snowthrower
unless you have been properly trained. Improper servicing
of the snowthrower can result in hazardous operation,
equipment damage, and voiding of the product warranty.
DANGER
Discharge chute contains rotating impel-
ler to throw snow. Never clear or unclog the
discharge chute with your hands. Fingers can
quickly become caught in the impeller. Always
use a clean-out tool.
Failure to observe these safety instructions
will result in traumatic amputation or severe
laceration.
Not for Reproduction
8
Operator Safety
DANGER
Keep hands, feet, and clothing away from
rotating parts. Rotating parts can contact or
entangle hands, feet, hair, clothing, or acces-
sories.
Failure to observe these safety instructions
will result in traumatic amputation or severe
laceration.
Whenever cleaning, repairing, or inspecting the
snowthrower, make sure the engine is OFF, spark plug wire
is disconnected, and all moving parts have stopped.
Do not put hands or feet near or under rotating parts. Keep
clear of the discharge opening at all times.
Never operate the snowthrower without proper guards, and
other safety devices in place and working.
Never leave the snowthrower unattended while engine is
running. Always disengage the auger and traction controls,
stop engine, and remove keys.
Keep all loose clothing away from the front of the
snowthrower and auger. Scarves, mittens, dangling
drawstrings, loose clothes, and pants can quickly become
caught in the rotating device and amputation will occur. Tie
up long hair and remove jewelry.
Run the machine a few minutes after discharging snow to
prevent freeze-up of the collector/impeller.
Disengage power to the collector/impeller when
snowthrower is transported or not in use.
WARNING
Objects can be picked up by auger and thrown
from chute. Never discharge snow toward
bystanders or allow anyone in front of the
snowthrower. Failure to observe these safety
instructions will result in death or serious injury.
Always wear safety glasses or eye shields during operation,
and while performing an adjustment or repair.
Always be aware of the direction the snow is being thrown.
Nearby pedestrians, pets, or property may be harmed by
objects being thrown.
Be aware of your environment while operating the
snowthrower. Don’t run over items such as gravel, doormats,
newspapers, toys, and rocks hidden under snow, as they
can all be thrown from the chute or jam in the auger.
Use extreme caution when operating on or crossing gravel
drives, walks, or roads.
Adjust the collector housing height to clear gravel or crushed
rock surface.
Never operate the snowthrower near glass enclosures,
automobiles, window wells, drop-offs, and the like without
proper adjustment of the discharge chute angle.
Familiarize yourself with the area in which you plan to
operate the snowthrower. Mark off boundaries of walkways
and driveways.
WARNING
Tragic accidents can occur if the operator is
not alert to the presence of children. Children
are often attracted to the unit and the operating
activity. Never assume the children will remain
where you last saw them.
Keep children out of the area during operation. Children are
often attracted to the equipment. Be mindful of all persons
present.
Be alert and turn unit off if children enter the area.
Never allow children to operate the unit.
Use extra care when approaching blind corners, shrubs,
trees, or other objects that may obscure vision. Children may
be present.
WARNING
Engines give o carbon monoxide, an odor-
less, colorless, poison gas. Breathing carbon
monoxide can cause nausea, fainting, or
death.
Start and run engine outdoors.
Do not run the engine in an enclosed area, even if doors or
windows are open.
Not for Reproduction
9
en
Operator Safety
WARNING
Fuel and its vapors are extremely ammable
and explosive. Always handle fuel with extreme
care.
Failure to observe these safety instructions can
cause a re or explosion which will result in
severe burns or death.
WHEN ADDING FUEL
Turn off engine and let cool at least 2 minutes before
removing the fuel cap and adding fuel.
Fill fuel tank outdoors or in a well ventilated area.
Do not overfill the fuel tank. To allow for the expansion of
gasoline, do not fill above the bottom of the fuel tank neck.
Keep fuel away from sparks, open flames, pilot lights, heat,
and other ignition sources.
Check fuel lines, cap, and fittings frequently for cracks or
leaks. Replace if necessary.
Use an approved fuel container.
If fuel spills, wait until it evaporates before starting engine.
WHEN STARTING ENGINE
Ensure that spark plug, muffler, fuel cap, and air cleaner (if
equipped) are in place and secured.
Do not crank the engine with the spark plug removed.
If fuel is spilled, do not attempt to start the engine, but move
the snowthrower away from the area of the spill, and avoid
creating any source of ignition, until the fuel vapors have
dissipated.
Do not over-prime the engine. Follow the engine starting
instructions in this manual.
If the engine floods, set choke (if equipped) to OPEN/RUN
position, move throttle (if equipped) to FAST position and
crank until engine starts.
WHEN OPERATING EQUIPMENT
Do not tip the snowthrower at an angle which causes the fuel
to spill.
Do not choke the carburetor to stop the engine.
Never run the engine with the air cleaner assembly (if
equipped) or the air filter (if equipped) removed.
WHEN CHANGING OIL
If you drain the oil from the top oil fill tube, the fuel tank must
be empty or fuel can leak out and result in a fire or explosion.
WHEN TRANSPORTING EQUIPMENT
Transport with fuel tank EMPTY, or with fuel shut-off valve
OFF.
WHEN STORING GASOLINE OR EQUIPMENT WITH FUEL
IN TANK
Store away from furnaces, stoves, water heaters, or other
appliances that have pilot light or other ignition source
because they can ignite fuel vapors.
WARNING
Safe operation of the snowthrower requires the
proper care and maintenance of the engine.
Disengage all clutches and shift into neutral before starting
the engine may cause personal injury.
Let the engine adjust to outdoor temperatures before starting
to clear snow.
Use a grounded three-wire plug for all snowthrowers
equipped with electric drive motors or electric starting
motors.
WARNING
Starting engine creates sparking.
Sparking can ignite nearby ammable gases.
Explosion and re could result.
If there is natural or LP gas leakage in area, do not start
engine.
Do not use pressurized starting fluids because vapors are
flammable.
WARNING
Running the engine produces heat. Engine
parts, especially mu er, become extremely
hot.
Failure to observe these safety instructions
could result in severe thermal burns on contact.
Never touch a hot engine or muffler. Allow muffler, engine
cylinder, and fins to cool before touching.
Remove debris from muffler area and cylinder area.
Install and maintain in working order a spark arrester before
using equipment on forest-covered, grass-covered, or brush-
covered unimproved land.
It is a violation of California Public Resource Code,
Section 4442, to use or operate the engine on any forest-
covered, brush-covered, or grass-covered land unless the
exhaust system is equipped with a spark arrester, as defined
in Section 4442, maintained in effective working order. Other
states or federal jurisdictions may have similar laws. Contact
the original equipment manufacturer, retailer, or dealer to
obtain a spark arrester designed for the exhaust system
installed on this engine.
Not for Reproduction
10
Operator Safety
WARNING
This snowthrower must be properly maintained
to ensure safe operation and performance.
Failure to observe the safety instructions in this
manual could result in death or serious injury.
When performing any maintenance or repairs on the
snowthrower, shut OFF the engine, disconnect spark plug
wire, and keep the wire away from the plug to prevent
someone from accidently starting the engine.
Check shear bolts and other hardware at frequent intervals
for proper tightness.
Keep nuts and bolts tight and keep snowthrower in good
condition.
Never tamper with safety devices. Check their proper
operation regularly and make necessary repairs if they are
not functioning properly.
Components are subject to wear, damage, and
deterioration. Frequently check components and replace
with recommended parts, when necessary.
Check control operation frequently. Adjust and service as
required.
Use only factory authorized replacement parts, or like, parts
when making repairs.
Always comply with factory specifications on all settings and
adjustments.
Use only factory authorized, or like, attachments and
accessories such as wheel weights, counterweights, or
cabs.
Never attempt to make any adjustments while the engine
is running (except when specifically recommended by the
factory).
WARNING
This snowthrower is only as safe as the opera-
tor. If it is misused, or not properly maintained,
it can be dangerous. Remember you are re-
sponsible for your safety and those around you.
Keep the area of operation clear of all persons, particularly
small children and pets.
Thoroughly inspect the area where the snowthrower will be
used and remove all doormats, sleds, boards, wires, and
other foreign objects.
Do not operate the snowthrower without wearing adequate
winter clothing.
Wear footwear that will improve footing on slippery surfaces.
Use caution to avoid slipping or falling especially when
operating the snowthrower in reverse.
Never operate the snowthrower without good visibility or
light. Always be sure of your footing, and keep a firm hold on
the handles.
Do not clear snow across the face of slopes. Use extreme
caution when changing direction on slopes. Do not attempt
to clear steep slopes.
Do not overload the machine capacity by attempting to clear
snow too quickly.
Never operate the snowthrower at high transport speeds on
slippery surfaces. Look behind the snowthrower and use
care when operating in reverse.
Do not use the snowthrower on surfaces above ground level
such as roofs of residences, garages, porches, or other such
structures or buildings.
Operators should evaluate their ability to operate the
snowthrower safely enough to protect themselves and
others from injury.
The snowthrower is intended to remove snow only. Do not
use the snowthrower for any other purpose.
Do not carry passengers.
After striking a foreign object, shut OFF the engine,
disconnect the cord on electric motors, thoroughly inspect
the snowthrower for any damage, and repair the damage
before restarting and operating the snowthrower.
If the snowthrower vibrates abnormally, shut OFF the
engine. Vibration is generally a warning of trouble. See an
authorized dealer if necessary for repairs.
For models equipped with electric starting motors,
disconnect the power cord after the engine starts.
Not for Reproduction
11
en
Operator Safety
1739967
1
Safety Decals
Before operating your snowthrower, read the safety decals
installed on your snowthrower. The cautions and warnings
are for your safety. To avoid a personal injury or damage
to your snowthrower, understand and follow all the safety
decals.
If any safety decals become worn or damaged and cannot
be read, order replacement decals from your local dealer.
A Part No. 1727207 Chute Danger Decal
B Part No. 1739967 Auger Danger Decal
C Part No. 276925 Engine Warning Decal
A
B
C
Not for Reproduction
12
Features and Controls
Snowthrower Controls and
Operation Decals
(Figure 2)
A — Auger Control
B — De ector Control Lever
C Electric Start Button
D Power Cord Receptacle
E Starting Instructions Decal / Steps 1-3
F Starting Instructions Decal / Step 4 & 5
D
C
HG I
J
K
L
M
B
2
1739977
A
F E
Engine Controls
G Choke Control Knob
H Fuel Tank and Cap
I Oil Fill Cap (Extended Dipstick)
J Primer Button
K ON/OFF or Push/Pull Key (as equipped)
L Starter Cord Handle
M Oil Drain
Not for Reproduction
13
en
Operation
Check / Add Oil
NOTICE: The engine was shipped from the factory without
oil. Before you start the engine, make sure you add oil
according to the instructions in this manual. If you start the
engine without oil, it will be damaged beyond repair and will
not be covered under the warranty.
1. Make sure the unit is level. Use a high quality
detergent oil classified “For Service SG, SH, SJ, SL, or
higher”. Synthetic 5W30 motor oil is acceptable for all
temperatures. DO NOT mix oil with gasoline. See Chart
for oil recommendations.
2. Remove the oil fill cap/dipstick (A, Figure 3) and wipe
with a clean cloth.
3. Insert the cap/dipstick and turn clockwise to tighten.
4. Remove the oil fill cap/dipstick and check the oil.
5. If necessary, add oil until the level reaches the FULL
mark on the oil fill cap/dipstick. Do not overfill.
6. Tighten the cap/dipstick securely.
* Below 40°F (4°C) the use of SAE 30 will result in hard starting.
** Above 80°F (27°C) the use of 10W-30 may cause increased
oil consumption. Check oil level more frequently.
WARNING
The operation of any snowthrower can result in foreign objects being thrown into the eyes, which can result in severe
eye damage. Always wear safety glasses or eye shields before beginning snowthrower operation.
Fuel Recommendations
Fuel must meet these requirements:
Clean, fresh, unleaded gasoline.
A minimum of 87 octane/87 AKI (91 RON).
High altitude use, see below.
Gasoline with up to 10% ethanol (gasohol) or up to
15% MTBE (methyl tertiary butyl ether) is acceptable.
NOTICE: Do not use unapproved gasoline, such as E85.
Do not mix oil in gasoline or modify the engine to run on
alternate fuels. This will damage the engine components
and void the engine warranty.
To protect the fuel system from gum formation, mix a fuel
stabilizer into the fuel. All fuel is not the same. If starting
or performance problems occur, change fuel providers
or change brands. This engine is certified to operate on
gasoline. The emissions control system for this engine is
EM (Engine Modifications).
High Altitude
At altitudes over 5,000 feet (1524 meters), a minimum
85 octane/85 AKI (89 RON) gasoline is acceptable. To
remain emissions compliant, high altitude adjustment is
required. Operation without this adjustment will cause
decreased performance, increased fuel consumption, and
increased emissions. See a Briggs & Stratton Authorized
Dealer for high altitude adjustment information.
Operation of the engine at altitudes below 2,500 feet
(762 meters) with the high altitude kit is not recommended.
Not for Reproduction
14
Operation
If engine floods, set the choke to the OPEN/RUN position
and crank until the engine starts.
Start the engine as follows:
1. Check the oil level. See the Check/Add Oil section.
2. Make sure auger control is disengaged.
3. Insert the ON/OFF key (A, Figure 5) and turn to the ON
position or insert the Push/Pull key, if equipped.
4. Turn the choke knob (B) fully clockwise if engine is cold.
NOTE: Do not use the choke to start a warm engine.
5. Push the primer button (C) two times.
NOTE: Do not use the primer to start a warm engine.
WARNING
Rapid retraction of the starter cord (kickback)
will pull your hand and arm toward the engine
faster than you can let go.
Broken bones, fractures, bruises, or sprains could result.
When starting engine, pull the starter cord slowly until resis-
tance is felt and then pull rapidly to avoid kickback.
6. Rewind Start: Firmly hold the starter cord handle
(D, Figure 5). Pull the starter cord handle slowly until
resistance is felt, then pull rapidly.
NOTE: If the engine does not start after three attempts,
see the Troubleshooting section.
WARNING
If the extension cord is damaged, it must be
replaced by the manufacturer (or its service
agent) or a similarly quali ed person to avoid a
hazard.
7. Electric Start: First connect the extension cord (E,
Figure 6) to the power cord receptacle (F) and then
into a wall receptacle. If additional extension cord is
required, make sure it is three-wire.
8. Electric Start: Depress the starter push button (G).
After you start the engine, first disconnect the extension
cord from the wall receptacle and then from the power
cord receptacle.
IMPORTANT: To extend the life of the starter, use
short starting cycles (five seconds maximum). Wait one
minute between starting cycles.
NOTE: If the engine does not start after three attempts,
see the Troubleshooting section.
Add Fuel
WARNING
Fuel and its vapors are extremely ammable
and explosive.
Fire or explosion can cause severe burns or
death.
When Adding Fuel
Turn engine off and let engine cool at least 2 minutes before
removing the fuel cap.
Fill fuel tank outdoors or in well-ventilated area.
Do not overfill fuel tank. To allow for expansion of the fuel, do
not fill above the bottom of the fuel tank neck.
Keep fuel away from sparks, open flames, pilot lights, heat,
and other ignition sources.
Check fuel lines, tank, cap, and fittings frequently for cracks
or leaks. Replace if necessary.
If fuel spills, wait until it evaporates before starting engine.
1. Clean the fuel cap area of dirt and debris. Remove the
fuel cap (A, Figure 4).
2. Fill the fuel tank with fuel. To allow for expansion of the
fuel, do not fill above the bottom of the fuel tank neck.
3. Reinstall the fuel cap.
Start the Engine
WARNING
The electric starter is equipped with a three-
wire power cord and plug designed to operate
on AC household current. The power cord must
be properly grounded at all times to avoid the
possibility of electric shock.
If your house does not have a three-wire grounded system, do
not use this electric starter. Contact a licensed electrician for
installation of a three-wire grounded system.
WARNING
Always connect the power cord rst to the switch box located
on the equipment and then plug the other end into a grounded
receptacle. After starting, disconnect the power cord from the
grounded receptacle rst.
Be sure that engine oil is at FULL mark on the oil fill cap/
dipstick. The snowthrower engine is equipped with an AC
electric starter and recoil starter. Before starting the engine,
be certain that you have read the following information.
Not for Reproduction
15
en
Operation
Stop the Engine
WARNING
Gasoline and vapors are extremely ammable
and explosive. Fire or explosion can cause
severe burns or death. DO NOT choke the
carburetor to stop the engine.
Before stopping the engine, allow it to idle for a few minutes
to help dry off any moisture.
1. Turn the ON/OFF or Push/Pull key (A, Figure 7) to the
OFF position and remove or pullout the Push/Pull key if
equipped.
2. Keep the ON/OFF or Push/Pull key out of the reach of
children. The engine cannot be started without the ON/
OFF or Push/Pull key.
Operate the Snowthrower
WARNING
Before operating, make sure the area in front
of the snowthrower is clear of bystanders or
obstacles.
DO NOT discharge snow toward a building as hidden
objects could be thrown with sufficient force to cause
damage.
1. Start the engine. See Start the Engine in this section.
2. Adjust the direction and angle of the discharge chute
(A, Figure 8). See Discharge Chute and Deflector in
this section.
3. Fully press and hold the auger control (B) to engage
the auger rotation. Releasing the auger control lever will
disengage the auger.
4. Push the unit into the snow.
NOTE: When clearing wet, heavy, snow, reduced your
speed, maintain full throttle, and clear less than the full
width of the unit.
5. Tip the handle bars (C) forward slightly. This will cause
the snowthrower to pull itself forward.
WARNING
Read Operator’s Manual before operating machine. This ma-
chine can be dangerous if used carelessly.
Never operate the snowthrower without all guards, covers,
and shields in place.
Never direct discharge towards windows or allow bystanders
near machine while engine is running.
Stop the engine whenever leaving the operating position.
Disconnect spark plug before unclogging the impeller
housing or the discharge chute and before making repairs or
adjustments.
When leaving the machine, remove the safety key. To reduce
the risk of fire, keep the machine clean and free from spilled
gas, oil, and debris.
Keep hands, feet, hair, and loose clothing away from any
moving parts on engine and snowthrower.
Temperature of muffler and nearby areas can exceed 150°F
(66°C). Avoid these areas.
DO NOT allow children to operate or be near snowthrower
while it is operating.
WARNING
Engines give o carbon monoxide, an odor-
less, colorless, poison gas. Breathing carbon
monoxide can cause nausea, fainting, or
death.
Start and run engine outdoors.
Do not run the engine in an enclosed area, even if doors or
windows are open.
Stop the Snowthrower
1. Release the auger control (A, Figure 9).
2. Turn the ON/OFF switch (B) to the OFF position and
remove or pull out PUSH/PULL key.
Not for Reproduction
16
Operation
Snowthrower Safety Test
DANGER
The discharge chute contains a rotating auger
to throw snow. Never clear or unclog the dis-
charge chute with your hands.
Fingers can quickly become caught and traumatic amputation
or severe laceration will result. Always use a clean-out tool to
clear or unclog the discharge chute.
DANGER
Hand contact with the rotating auger inside the
discharge chute is the most common cause of
injury associated with snowthrowers.
This snowthrower is capable of amputating hands and feet,
and throwing objects. Read and observe all the safety instruc-
tions in this manual. Failure to do so will result in death or
serious injury.
Test - Auger/Impeller
1. Start unit and engage auger control (A, Figure 9).
2. Release auger control.
3. Auger must stop in 5 seconds or less.
Discharge Chute and De ector
Manual Chute Rotation
Grasp the chute handle (A, Figure 10) on the deflector
and rotate the discharge chute to the left, right or forward
positiin. A tension plate holds the chute in the desired
position.
NOTE: Do not use the chute handle to lift the unit.
Manual Deflector Adjustment
Loosen the deflector wing knob (B, Figure 10) and adjust
the deflector up or down to control the snow discharge
height and distance. Tighten the wing knob securely to hold
the desired deflector adjustment.
Clear a Clogged Discharge Chute
DANGER
Hand contact with the rotating impeller inside
the discharge chute is the most common
cause of injury associated with snowthrowers.
Never clear or unclog discharge chute with
your hands, or while engine is running.
Fingers can quickly become caught and traumatic amputation
or severe laceration can result.
1. SHUT OFF THE ENGINE!
2. Wait 10 seconds to be sure that the impeller blades
have stopped rotating.
3. Use a clean-out tool to remove snow from the auger
housing.
Operating Tips
1. Most efficient snow removal is accomplished when
snow is removed immediately after it falls.
2. For complete snow removal, slightly overlap each swath
previously taken.
3. Snow should be discharged downwind whenever
possible.
4. On gravel or crushed rock surfaces, push down slightly
on the handle bars to avoid ingesting rocks. DO NOT
allow rocks and gravel to be picked up and thrown from
snowthrower.
5. After the snow removal has been completed, allow the
engine to run for a few minutes, to melt accumulated
snow and ice.
6. Clean the snowthrower thoroughly after each use.
7. Before starting snowthrower, always inspect auger for
ice accumulation and/or debris, which could result in
snowthrower damage.
8. Check oil level before every start. Make sure the oil is at
the FULL mark on the oil fill cap/dipstick.
Not for Reproduction
17
en
Snowthrower
After Each Use
Remove accumulated snow and slush from the unit to prevent
freezing of controls.
Every 8 Hours or Daily
Perform impeller safety tests.
Every 25 Hours or Annually
Check snowthrower for loose hardware.
Adjust auger control cable if necessary.
See Dealer Annually to
Ensure rubber auger wear is not a ecting performance.
Engine
First 5 Hours
Change oil.
Every 8 Hours or Daily
Check engine oil level.
Every 50 Hours or Annually
Change engine oil.
Check mu er and mu er guard.
Annually
Replace spark plug.
Check valve clearance. *
* Not required unless problems are noted with engine
performance. See authorized dealer.
Emissions Control Statement
Maintenance, replacement, or repair of the emissions
control devices and systems may be performed by any
non-road engine repair establishment or individual.
However, to obtain “no charge” emissions control service,
the work must be performed by a factory authorized dealer.
Change the Oil
Remove Oil
Used oil is a hazardous waste product and must be
disposed of properly. Do not discard with household waste.
Check with your local authorities, service center, or dealer
for safe disposal / recycling facilities.
1. With engine off but still warm, disconnect the spark plug
wire (A, Figure 11) and keep it away from the spark
plug.
NOTE: To access the spark plug wire, you must first
remove the snow hood from the engine. See Replace
the Spark Plug in this section.
2. Tilt the unit back slightly, then remove the oil drain cap
(B, Figure 12). Drain the oil into an approved receptacle.
3. After the oil has drained, install and tighten the oil drain
cap.
Add Oil
1. Place engine level.
2. Clean the oil fill area of any debris.
3. See Specifications section for oil capacity.
4. Remove the dipstick (C, Figure13) and wipe with clean
cloth.
5. Pour the oil slowly into the engine oil fill (D). DO NOT
overfill. Wait one minute and recheck the oil level.
6. Install and tighten dipstick.
7. Remove the dipstick and check the oil level. It should be
at the top of the full indicator (E) on the dipstick.
8. Install and tighten dipstick.
Maintenance
Not for Reproduction
18
Maintenance
Inspection
1. Start the engine.
2. Engage the auger control. The auger should turn.
3. Release the auger control. The auger should stop within
5 seconds.
If the auger does not turn or stop as indicated above,
perform the adjustment procedure, or take the unit to your
local authorized dealer for repair.
Adjustment
1. Turn off the engine and remove the key. Wait for all
moving parts to stop.
2. Slide the cable cover (A, Figure 14) up to expose the
cable adjustment loops (B) and Z-bend (C).
3. Disengage the cable Z-bend from the cable loops, and
install it in the next highest loop to increase belt tension.
Slide the cable boot back into place.
NOTE: There must be some slack in the cable when the
control is released.
4. Keeping clear of the auger, reinsert the key, start the
engine, and perform the Inspection procedure again. If
the auger does not turn or stop as indicated, take the
unit to your local authorized dealer for repair.
Auger Cable Adjustment
WARNING
Do not over-tighten, as this may lift the lever and cause the
auger drive to be engaged without depressing the auger drive
control.
WARNING
The auger must stop within 5 seconds after releasing the con-
trol. If it does not, see an authorized dealer.
If the auger no longer turns when the control is engaged,
or if the belt slips under load, the auger cable or belt may
have stretched. This can be compensated for by adjusting
the auger cable. If the belt is too worn or broken, see your
authorized dealer for repair.
NOTICE: The auger must not turn unless the auger control
is engaged. The auger must disengage within 5 seconds
after the auger control is released. If it does not, see your
authorized dealer before further use.
Not for Reproduction
19
en
Storage
Remove from Storage
1. Raise the upper handle to the operating position and
tighten the knobs that secure the upper handle.
2. Fill the fuel tank with fresh fuel.
3. Check the spark plug. Make sure the gap is correct. If
the spark plug is worn or damaged, replace.
4. Make sure all fasteners are tight.
5. Make sure all guards, shields, and covers are in place.
Storage
WARNING
Fuel and its vapors are extremely flammable
and explosive.
Fire or explosion can cause severe burns or
death.
When Storing Fuel or Equipment with Fuel in Tank
Store away from furnaces, stoves, water heaters or other
appliances that have pilot lights or ignition sources because
they can ignite fuel vapors.
Fuel System
Fuel can become stale when stored over 30 days. Stale
fuel causes acid and gum deposits to form in the fuel
system or on essential carburetor parts. To keep fuel fresh,
use Briggs & Stratton® Advanced Formula Fuel Treatment
& Stabilizer, available wherever Briggs & Stratton genuine
service parts are sold.
For engines equipped with a FRESH START® fuel cap,
use Briggs & Stratton FRESH START® available in a drip
concentrate cartridge.
There is no need to drain gasoline from the engine if a fuel
stabilizer is added according to instructions. Run the en-
gine for 2 minutes to circulate the stabilizer throughout the
fuel system before storage.
Engine Oil
While the engine is still warm, change the engine oil.
Snowthrower
1. Thoroughly clean the snowthrower.
2. Lubricate all lubrication points (see authorized dealer).
3. Make sure all nuts, bolts, and screws are securely
fastened. Inspect all visible moving parts for damage,
breakage, and wear. Replace if necessary.
4. Touch up all rusted or chipped paint surfaces.
5. Cover the bare metal parts of the auger and impeller
with rust preventative.
6. If possible, store your snowthrower indoors and cover it
to protect from dust and dirt.
7. On models with folding handles, loosen the knobs that
secure the upper handle. Rotate the upper handle
forward.
8. If stored outdoors, place the snowthrower on blocks and
ensure the entire machine is off the ground. Cover the
snowthrower with a heavy tarpaulin.
Not for Reproduction
20
Troubleshooting
PROBLEM LOOK FOR REMEDY
Auger does not stop
within 5 seconds
after control lever is
released.
Auger control cable out of
adjustment
Adjust auger control cable. Refer to “Cable Adjustment” in the
Maintenance section of this manual. If the auger does not stop
within 5 seconds, see authorized dealer for repair.
Discharge chute or
de ector does not work
(remote-manual).
Discharge chute
or deflector needs
lubrication.
See authorized dealer.
Discharge chute or
deflector is frozen .
Put snowthrower in heated garage or let unit run for a few minutes
or clean off any snow and ice from the base of the chute.
Engine does not start. Key is off or not installed. Turn key in to the ON position.
Primer not pressed. Press primer button twice and start.
Frozen engine Put snowthrower in heated garage to unfreeze engine.
Out of fuel. Fill fuel tank.
Choke open - cold
engine.
Turn choke to closed, then press primer and start engine.
Engine flooded. Turn choke to open; crank the engine repeatedly until it starts.
No spark. Connect spark plug wire or replace spark plug.
Water in fuel, or old fuel. Drain tank. (Dispose of fuel at an authorized hazardous waste
facility.) Fill with fresh fuel.
Cord not plugged in or
circuit breaker tripped
(Electric Start models).
Plug in cord or replace defective cord; reset circuit breaker.
Engine starts hard or
runs poorly.
Fuel mixture too rich. Move choke to OPEN position.
Spark plug faulty, fouled,
or gapped incorrectly.
Clean and re-gap spark plug or see authorized dealer.
Fuel cap vent is blocked. Clear vent.
Excessive vibration. Loose parts or damaged
auger.
Stop engine immediately. See authorized dealer.
Scraper bar does not
clean hard surface.
Excessive snow left
behind.
See authorized dealer to determine if replacement scraper bar is
necessary.
Scraper bar worn. See authorized dealer for replacement.
Unit fails to discharge
snow.
Auger drive belt loose or
damaged.
Adjust auger control cable. Refer to “Cable Adjustment” in the
Maintenance section of this manual.
See authorized dealer for belt replacement.
Discharge chute clogged
with snow.
Stop engine immediately. Always use a clean-out tool to clear a
clogged discharge chute, not your hands. Clean discharge chute
and inside of auger housing. Refer to “Warnings” in Operator
Safety section.
Foreign object lodged in
auger.
Stop engine immediately. Always use the clean-out tool to clear a
clogged chute, not your hands. Remove object from auger. Refer
to “Warnings” in Operator Safety section.
Rubber auger is worn or
damaged.
See authorized dealer for replacement.
Not for Reproduction
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180
  • Page 181 181
  • Page 182 182
  • Page 183 183
  • Page 184 184
  • Page 185 185
  • Page 186 186
  • Page 187 187
  • Page 188 188
  • Page 189 189
  • Page 190 190
  • Page 191 191
  • Page 192 192
  • Page 193 193
  • Page 194 194
  • Page 195 195
  • Page 196 196
  • Page 197 197
  • Page 198 198
  • Page 199 199
  • Page 200 200
  • Page 201 201
  • Page 202 202
  • Page 203 203
  • Page 204 204
  • Page 205 205
  • Page 206 206
  • Page 207 207
  • Page 208 208
  • Page 209 209
  • Page 210 210
  • Page 211 211
  • Page 212 212
  • Page 213 213
  • Page 214 214
  • Page 215 215
  • Page 216 216
  • Page 217 217
  • Page 218 218
  • Page 219 219
  • Page 220 220
  • Page 221 221
  • Page 222 222
  • Page 223 223
  • Page 224 224
  • Page 225 225
  • Page 226 226
  • Page 227 227
  • Page 228 228
  • Page 229 229
  • Page 230 230
  • Page 231 231
  • Page 232 232
  • Page 233 233
  • Page 234 234
  • Page 235 235
  • Page 236 236
  • Page 237 237
  • Page 238 238
  • Page 239 239
  • Page 240 240
  • Page 241 241
  • Page 242 242
  • Page 243 243
  • Page 244 244
  • Page 245 245
  • Page 246 246
  • Page 247 247
  • Page 248 248
  • Page 249 249
  • Page 250 250
  • Page 251 251
  • Page 252 252
  • Page 253 253
  • Page 254 254
  • Page 255 255
  • Page 256 256
  • Page 257 257
  • Page 258 258
  • Page 259 259
  • Page 260 260
  • Page 261 261
  • Page 262 262

Simplicity 1696211-00 Manuale utente

Tipo
Manuale utente
Questo manuale è adatto anche per