Metrologic IS4320 ScanGlove Programming Manual

METROLOGIC INSTRUMENTS, INC.

IS4320 ScanGlove

Programming Guide

MLPN 2405

Printed in USA

April 1998

ii

Locations:

USA Corporate Headquarters Europe

Metrologic Instruments, Inc. Metrologic Instruments GmbH

Blackwood, NJ 08012 Munich, Germany

Customer Service: 1-800-ID-METRO Tel: 49-89-89018-0

Tel: 609-228-8100 Fax: 49-89-89019-200

Fax: 609-228-6673

ASIA

South America

Metrologic Asia (PTE) Ltd.

Metrologic Instruments Singapore 417818

CEP 04571-090, São Paulo-SP, Brasil Tel: 65-842-7155

Outside Brazil: Fax: 65-842-7166

Tel: 55-11-5505-6568

Fax: 55-11-5505-1681

In Brazil:

Tel: 55-11-5505-2396

Fax: 55-11-5507-2301

Copyright

®

be reproduced, transmitted, or stored in any form or by any means without prior written

consent, except by reviewer, who may quote brief passages in a review, or provided for

in the Copyright Act of 1976.

Products and brand names mentioned in this document are trademarks of their

respective companies.

iii

Table of Contents

Programming the Scanner ........................................ 1

Enter Program Mode ............................................ 2

Recall Defaults................................................. 2

Laser Activation Range .......................................... 3

Laser Operation ................................................ 4

Same Symbol Re-Scan .......................................... 5

Beeper Tones.................................................. 6

Audible Indicators for Communication Timeouts...................... 7

RS-232 Interface ............................................... 8

RS-232 Parameter - Baud Rate .................................. 8, 9

RS-232 Parameter - Parity ...................................... 10

RS-232 Parameter - Data Bits .................................... 11

RS-232 Parameter - Hardware Handshaking ........................ 12

RS-232 Parameter - Software Handshaking ......................... 13

RS-232 Parameter - Intercharacter Delay ........................... 14

RS-232 Parameter - Scanning Control (DTR Signal) ................. 15

Record Header/Terminator Select.............................. 15-17

RS-232 Parameter - UPC/EAN Identifiers .......................... 18

Light Pen Options ............................................. 19

Code Type Selections ....................................... 20, 21

Minimum Code Length for All Code Types ......................... 22

iv

UPC/EAN Code............................................... 22

UPC-A Options ............................................... 23

UPC-E Options ............................................... 24

Supplemental UPC Options ..................................... 25

Code 39 .................................................. 26, 27

Codabar ..................................................... 27

Interleaved 2 of 5 (ITF) ......................................... 28

Interleaved 2 of 5 (ITF) Symbol Lengths ........................ 29-32

MSI - Plessey Check Digit ................................... 32, 33

Test Modes................................................... 34

Special Features............................................ 35, 36

Reserved Codes ............................................ 37-41

Disclaimer ................................................... 42

Index .................................................... 43, 44

**

1

Programming the Scanner

The IS4320 is shipped from the factory programmed to a set of default

parameters. Defaults are noted in the following pages by double asterisks next

to the bar code labels. Modifications to the default program to match the host

system are made using bar codes contained in this manual.

1. Connect the scanner to the host system or power source. (Refer to the

Installation and User’s Guide.)

2. Scan the ENTER/EXIT PROGRAM MODE bar code. (The unit will

beep three times.)

3. Scan by positioning the output window within two inches of each code.

(When you scan the first menu selection, the laser will stay on until you

scan the ENTER/EXIT PROGRAM MODE code again. If no scanning

occurs for 30 seconds while the scanner is in program mode, the unit

will beep three times and all changes made will be lost. If this occurs,

return to Step 1.)

4. After completing the scanning of the appropriate configuration options,

scan the ENTER/EXIT PROGRAM MODE bar code again. (The new

options will be saved and the scanner is ready for normal operation.)

Enter/Exit

Program Mode

**

R18

R19

DF1

Enter/Exit Program Mode

2

Enter Program Mode

**Ability to Enter Program

When this option is selected, enter

Mode After Any Scan

programming by scanning the

ENTER/EXIT PROGRAM MODE bar

code after power up or during normal

scanning operation.

Enter Program Mode Only

When this option is selected, the scanner

on First Scan

will only enter program mode after power-

up. Scan the ENTER/EXIT PROGRAM

MODE bar code immediately after the

scanner first receives power. This option

prevents the scanner from accidentally

entering program mode during normal

scanning operation.

Recall Defaults

If during programming of the scanner, there is a need to return the scanner to

the original factory settings, scan the RECALL DEFAULTS bar code. Any

settings selected during that session or any previous session will be lost.

Recall Defaults

DF1

RS1

RS3

RS2

RS4

Recall Defaults

3

Laser Activation Range

Short Range Activation

When this option is selected, the IR

Out of the Stand

sensor guarantees to activate when the

scanning window is positioned three

inches from the object.

Short Range Activation

When this option is selected, the IR

In the Stand

sensor guarantees to activate when an

object is presented three inches from

the scanning window.

**Long Range Activation

When this option is selected, the IR

Out of the Stand

sensor guarantees to activate when the

scanning window is positioned eight

inches from the object.

**Long Range Activation

When this option is selected, the IR

In the Stand

sensor guarantees to activate when an

object is presented eight inches from

the scanning window.

**

RS5

RS6

LP8

Enter/Exit Program Mode

4

Laser Operation

**Normal Scan

This option is the default setting. When the laser

activates by the IR sensor, the laser beam will emit

from the output window. It will also display a

constant, horizontal line until it senses a bar code

or until the scanner timeout elapses.

Pulsing Scan

When the laser activates by the IR sensor, the laser

beam will emit from the output window. It will also

display a pulsing, horizontal line until it senses a

bar code or until the scanner timeout elapses.

Custom Scan

This option is available for special applications.

Do not scan the CUSTOM SCAN bar code unless

instructed by a Metrologic representative.

DF1

R30

R31

Recall Defaults

5

Same Symbol Re-Scan

The scanner is programmed with a same symbol

Short Same

timeout. For SHORT SAME SYMBOL RE-SCAN,

Symbol Re-Scan

the time delay is ½ second, while the LONG SAME

SYMBOL RE-SCAN delay is 1 second. These numbers

represent the amount of time that a bar code must be out of

the scan field before it can be scanned again.

** Long Same Symbol Re-Scan

**

BP1

BP2

BP3

BP4

Enter/Exit Program Mode

6

Beeper Tones

Program the scanner to emit a certain tone.

Alternate Tone 1 ................................. Low Tone

Alternate Tone 2 ................................. High Tone

(Default)

Alternate Tone 3 ................................. Medium Tone

No Tone

Alternate Tone 1

**Alternate Tone 2

Alternate Tone 3

No Tone

DF1

OC5

OC6

OC7

OC8

OC9

R50

R51

Recall Defaults

7

Audible Indicators for Communication Timeouts

Two Second Timeout

When this option is selected, the scanner will

timeout if it does not transmit its data to the

host after two seconds during communica-

tion. This is only valid in modes where some

type of hand-shaking is involved.

**No Two Second Timeout

Razz Beep on Timeout

When this option is selected, The scanner

will produ ce an audible razzberry tone

when communications timeout.

** No Tone After Timeout

Three Beep on Timeout

When this option is selected, the scanner will

beep three times when communications time-

out.

** Beep Before Transmit

When this option is selected, the scanner will

beep before each label transmits.

Beep After Transmit

When this option is selected, the scanner will

beep after each label transmits.

**

LP2

BR1

BR2

BR3

BR4

Enter/Exit Program Mode

8

RS-232 Interface

** Enable RS-232 Interface

RS-232 Parameter - Baud Rate

A baud rate is a unit that measures the speed with which information transfers.

The baud rate of the scanner must equal the baud rate of the host device. The

available baud rates range from 150 to 19200.

150 Baud Rate

300 Baud Rate

600 Baud Rate

1200 Baud Rate

DF1

BR5

BR6

BR7

BR8

Recall Defaults

9

2400 Baud Rate

4800 Baud Rate

** 9600 Baud Rate

19200 Baud Rate

**

PA1

PA3

PA2

PA4

Enter/Exit Program Mode

10

RS-232 Parameter - Parity

Parity is an additional digit that makes the number of bits in the ASCII code

odd or even. The scanner’s parity must match the host’s parity.

**Space Parity

Select this option to make the parity bit always 0.

Even Parity

Select this option to make the additional parity bit

either a 0 or 1 to guarantee an even number of bits.

Mark Parity

Select this option to make the parity bit always 1.

Odd Parity

Select this option to make the additional parity bit

either a 0 or 1 to guarantee an odd number of bits.

DF1

D81

D82

Recall Defaults

11

RS-232 Parameter - Data Bits

RS-232 serial communication requires ASCII data to

8 Data Bits

transmit in either 7 or 8 data bits. In addition, one parity

bit will transmit. If necessary, scan the appro-priate bar

code that matches your host device’s requirements.

** 7 Data Bits

**

HH1

HH2

R56

R57

Enter/Exit Program Mode

12

RS-232 Parameter - Hardware Handshaking

To prevent scanned information from being lost during

Enable RTS/CTS

transmission, your host device may require an RTS/

CTS signal. When RTS/CTS (R

eady To Send/Clear To

S

end) enables, the scanner will output an RTS signal

and wait for a CTS signal before any data transmits. The

default setting of RTS/CTS disables. If necessary, scan

the ENABLE RTS/CTS bar code.

** Disable RTS/CTS

** Character RTS/CTS

When this option is selected, the scanner will

activate and deactivate its RTS signal on each

character that it transmits.

Message RTS/CTS

When this option is selected, the scanner will

activate and deactivate its RTS signal on each

message that it transmits. This mode should

normally enable for Sanyo registers.

DF1

SH2

SH1

SH4

SH3

Recall Defaults

13

RS-232 Parameter - Software Handshaking

For control of the data transmission process, use the following parameters

instead of or in addition to the RTS/CTS hardware handshaking option.

ACK/NAK When this option is enabled,the

Enable ACK/NAK

scanner will not scan again unless

after transmission of a bar code it

receives an ACK (ASCII 06H).

The scanner will retransmit the

bar code, if it receives an NAK

(ASCII 15H).

** Disable ACK/NAK

XON/XOFF When this option is enabled, the

Enable XON/XOFF

scanner will stop transmission

whenever it receives an XOFF

(ASCII 13H). Transmission will

resume after it receives an XON

(ASCII 11H).

**DisableXON/XOFF

**

R20

R21

R22

R23

Enter/Exit Program Mode

14

RS-232 Parameter - Intercharacter Delay

The time specified with an intercharacter delay bar code represents the interim

of time between transmission of characters. Some host systems require this

delay when receiving transmissions. If necessary, scan the appropriate bar

code.

** No Intercharacter Delay

1 Millisecond Intercharacter Delay

5 Millisecond Intercharacter Delay

25 Millisecond Intercharacter Delay

DF1

HH3

HH4

R32

TR1

TR2

Recall Defaults

15

RS-232 Parameter - Scanning Control (DTR Signal)

When the DTR (Data Terminal Ready) input is

Enable DTR Input

enabled, the scanner will not transmit unless an

active (+12V) DTR signal is present on the scanner’s

DTR input pin. You can disable the scanner by making

DTR inactive (-12V) at the DTR input pin.

The DTR Scan Disable feature will prevent any

** Disable DTR Input

scanning when the Enable DTR input feature is chosen.

Before enabling the Enable DTR Scan Disable feature,

scan the Enable DTR Input bar code. To turn off this

feature, scan the Recall Defaults bar code.

Enable DTR Scan Disable

Record Header/Terminator Select

CR

When this option is on, the scanner will transmit a C

arriage

R

eturn after each bar code.

CR Off

**CR On

**

TR4

TR3

TR6

TR5

Enter/Exit Program Mode

16

LF

When this option is on, the scanner will transmit a L

ine Feed

after each bar code.

**

LF On

LF Off

STX Prefix

When this option is on, the scanner will transmit a S

tart of

T

eXt (ASCII 02H) before each bar code.

STX Prefix On

** STX Prefix Off

La pagina sta caricando ...

Metrologic IS4320 ScanGlove Programming Manual

Metrologic IS4320 ScanGlove Programming Manual

in altre lingue

Documenti correlati

Altri documenti