INSTALLATION GUIDE
HID® BEEKS001 Install Guide PLT-05252, Rev. A.1
© 2020 HID Global Corporation/ASSA ABLOY AB. All rights reserved. This document may not be reproduced, disseminated or republished in any form without the prior written permission of HID Global Corporation. HID GLOBAL, HID, the HID Brick logo, the Chain Design, BluFi, Bluzone, and BEEKs are trademarks or registered
trademarks of HID Global, ASSA ABLOY AB, or its aliate(s) in the US and other countries and may not be used without permission. All other trademarks, service marks, and product or service names are trademarks or registered trademarks of their respective owner. 2020-09-16-hid-beeks001-installation-guide-in-en
hidglobal.com An ASSA ABLOY Group brand
Overview
System components
Terminology Sensor locations
Best practices
Pre-requisites
Specifications
The BEEKs™ Install Guide covers the basics of the BLE beacon
setup and provisioning of equipment with Bluzone Cloud
account and project. This install guide is intended for install
technicians.
BEEKs™ Bluetooth Low-Energy (BLE) beacons are among
the most advanced beacons in the industry. Being fully Apple
iBeacon and Google Eddystone compatible, BEEKs beacons
may be used for any standard beacon application that
provides location based promotional or way-finding services
to smartphone users. BEEKs beacons are available in multiple
form factors and sensor configurations.
When combined with HID Global’s end-to- end IoT ecosystem,
that includes BluFi™ BLE to WiFi gateways and the Bluzone™
cloud services, BEEKs can be centrally managed remotely
through the cloud to transfer new messages, firmware
updates and battery status checks. Their unique design allows
BEEKs to broadcast reliably even in densely populated WiFi
environments.
The BLE radio enables the Beacon to transmit condition
monitoring, proximity messaging, way finding and asset
location. Bluzone allows you to control the transmitting
capabilities of the Beacon. The Beacon provides the ability to
transmit in iBeacon, Eddystone or sBeacon format.
The BEEKs Beacons link to ID64 with a QR code printed/
labeled on the outer casing.
Maximum of 15 – 20 beacons per BluFi for best results
Maximum 20 – 30 meters from beacon to BluFi for best results
(distance will decrease for increased interference/ blockages)
Recommended epoxy glue for mounting: Loctite AA 330,
Devcon 5-minute (for BEEKS001-CM)
Network troubleshooting
2.4 GHz WiFi only
HTTPS port 443 must be open
DHCP required
1 Mbps upload speed required
Captive WiFi portals not compatible
Compatible certificate formats: .pem, .der
BluFi MAC address whitelisting may be required on some networks
Set up Bluzone account
Download Bluzone mobile app
Additional installation guides are available and can be found at :
https://hid.gl/HID-BluFi-installation
ITEM DESCRIPTION
1 BluFi™ model BluFi-AC00 – Bluetooth to WiFi Gateway.
2 Bluzone – Cloud Fleet Management and Condition
Monitoring dashboard.
3BEEKs™ model BEEKS001–XX Bluetooth Low Energy Beacons.
ITEM DESCRIPTION
1 Bluzone – Secure cloud-based SaaS to centrally manage
BEEKs via BluFi gateways. Additionally, monitor, store
and analyze performance data collected from deployed
BEEKs fleet.
2 BluFi Gateway – Receives data from BEEKs over
Bluetooth and sends to Bluzone Cloud.
3 BEEKs CM – Sends vibration and temperature data to
BluFi.
4 Asset – Equipment to be monitored or tracked
T
R
A
X
Z
Y
T
A
R
Orientation
A = Axial
R = Radial
T = Tangential
Vertical motor mount
Horizontal motor mount
13
2
BLE Beacons model number BEEKS001
Dierent Configurations based on environments and use case
BEEKS001-
CM
BEEKS001-
Industrial
BEEKS001-
Lite
BEEKS001-
Plus
BEEKS001-CM Condition monitoring for industrial
applications, sends vibration
(accelerometer) and temperature
data. Enclosure is sealed with epoxy
to preserve mechanical frequency
response. Epoxy-mount.
BEEKS001-Industrial Status/ process monitoring, sends
basic motion and temperature data.
VHB tape-mount.
BEEKS001-Lite Asset location and way-finding. VHB
tape-mount.
BEEKS001-Plus Asset location and way-finding with
longer battery life. VHB tape-mount.
Operating temperature -13°F to +185°F (-25°C to +85°C)
Storage temperature -22°F to +185°F (-30°C to +85°C)
Specifications
Standard Protocol Bluetooth Low Energy 4.2
Frequency range 2400-2483.5 MHz
No of channels 40
Modulation GFSK
Mode of operation Half duplex
RF output power +5dBm (<10mW)
Antenna PCB, 0 dbi omnidirectional
1
4
3
WiFi
WiFi
Bluetooth
Bluetooth
2
Beacons should be mounted to a clean, flat, rigid surface of the
asset to be monitored.
For Condition Monitoring Applications with BEEKS001-CM, the
beacon should be oriented such that its three axes are parallel to
the three axes of the asset, close to the source of vibration.
Name BEEKS001-
CM
BEEKS001-
Industrial
BEEKS001-
Lite
BEEKS001-
Plus
Length x width 2.36 in × 0.83
x 0.98 in
(60 × 21 x 25
mm)
2.36 in × 0.83
x 0.98 in
(60 × 21 x 25
mm)
2.36 in × 0.83
x 0.98 in
(60 × 21 x 25
mm)
2.41 x 1.46 in
(61.3 x 37.2
mm)
Weight 1.37 oz (39 g) 1.0 oz (28 g) 1.0 oz (28 g) 2.7 oz (76 g)
Housing material Polycarbonate and ABS
Data rates 1Mbit/s
Battery type 3.6V / 2600mAh – Primary Lithium
3.6V / 2600 mAh
(3ea)
3.6V / 7200
mAh
Battery duration Up to 3 yrs Up to 5 yrs Up to 8 yrs
HID® BEEKS001 Install Guide PLT-05252, Rev. A.1 INSTALLATION GUIDE
hidglobal.com An ASSA ABLOY Group brand
1Initial setup For more detailed information, visit https://hid.gl/HID-BEEKs-installation
1. Account setup
1. Visit bluzone.io and register a new account.
Verify your email by clicking on the link
emailed to you.
2. Project setup
1. Use the dropdown menu in the top right
portion of the screen to create a new
project.
2. Go to Settings and send a Product
Activation request for your use case e.g.
RTLS, Status Monitoring or Advanced
Condition Monitoring, depending on the
SaaS model you have purchased. Your
product features will be activated within
24 hours.
Assign the beacon a name that coincides with
the asset on which it is installed. It is also good
practice to use a label-maker to place a label
on the beacon that matches this name.
3. Bluzone mobile app setup
1. Download the Bluzone mobile app from
Google Play or the iOS App Store.
2. Login to your account with Bluzone
credentials.
4. BluFi provisioning
1. Plug BluFi into power source for initial
setup.
2. In Bluzone app, tap Provision > BluFi
3. Hold mobile device close to BluFi and select
device with highest signal strength (swipe
down to refresh list).
4. Follow each step within Bluzone app as
instructed to define location and picture of
the installation place (optional).
5. When prompted for Template, create a
new Template with your WiFi SSID and
password.
5. BEEK provisioning
1. Place BEEK close to BluFi (don’t install on
assets yet).
2. For each beacon, hold mobile phone close
to BEEK and select device with highest
signal strength (swipe down to refresh list).
Continue the steps for each BEEK.
3. When prompted for a Template, select the
template corresponding to your use case
e.g. “Default Beacon Template - Condition
Monitoring AI” for Advanced Condition
Monitoring with BEEKS001-CM.
HID® BEEKS001 Install Guide PLT-05252, Rev. A.1 INSTALLATION GUIDE
hidglobal.com An ASSA ABLOY Group brand
2BEEKs and BluFi installation
1. BluFi installation
1. BluFi should be installed within 100ft (30m) of monitored
assets (shorter distances required for environments with
obstructions).
3. Surface preparation
1. Ensure the asset installation surface is clean and free
of oil, dirt, rust, and paint chips and the beacon is not
covered by metal to ensure good radio transmission.
2. Beacons should be mounted to a clean, flat, rigid surface
of the asset to be monitored. For vibration monitoring
with BEEKS001-CM, the mounting should be close to the
source of vibration. The beacon should be oriented such
that its three axes are parallel to the three axes of the
asset.
4. Policy creation
Now you are ready to use the beacon for your use case.
Start creating policies as decribed in our on-line manual
hid.gl/On-line-manual
4. BEEKs installation
1. Standard beacons may simply be mounted by using the
integrated peel-o sticker.
2. BEEKS001-CM requires special mounting with Epoxy
glue to ensure proper pick-up of the vibration data of the
underlying asset. We recommend Devcon 5-minute or
Loctite AA 330
3. Apply line of epoxy to bottom of beacon.
4. Place beacon and press firmly.
5. Wait five minutes and confirm beacon is secure.
2. BEEKs location
1. Place beacons near the desired assets (don’t install yet).
2. In Bluzone console, go to BluFi > {BluFi Name} >
Statistics and scroll down to the Scan Map.
3. Verify that each beacon sees at least one BluFi. (-75 dBm
or higher is desired). Move BluFi’s if necessary.
For more detailed information, visit https://hid.gl/HID-BEEKs-installation
AC BluFi Option
T
R
A
X
Z
Y
T
A
R
Orientation
A = Axial
R = Radial
T = Tangential
Vertical motor mount
Horizontal motor mount
HID® BEEKS001 Install Guide PLT-05252, Rev. A.1 INSTALLATION GUIDE
hidglobal.com An ASSA ABLOY Group brand
3Regulation Information For more detailed information, visit https://hid.gl/HID-BEEKs-installation
Czech
Společnost HID Global tímto
prohlašuje, že toto radiové zařízení,
číslo modelu BEEKS001, odpovídá
požadavkům směrnice 2014/53/EU.
Úplný text EU Prohlášení o shodě je
k dispozici na následující internetové
adrese: www.hidglobal/certications
Tento výrobek používá následující
frekvence:
-frekvenční pásmo 2,4 GHz, přičemž
výstupní RF výkon je nižší než +5dBm
EIRP
Greek
∆ια του παρόντος, η HID Global
δηλώνει ότι ο παρών ραδιοεξοπλισμός
με αριθμό Mοντέλου BEEKS001
βρίσκεται σε συμμόρφωση με την
Oδηγία 2014/53/EΕ. Το πλήρες κείμενο
της δήλωσης συμμόρφωσης για την
Ευρωπαϊκή Ένωση είναι διαθέσιμο
στην ακόλουθη διαδικτυακή διεύθυνση:
www.hidglobal/certications
Το παρόν προϊόν λειτουργεί στις
ακόλουθες συχνότητες:
•Ζώνη των 2,4 GHz με ισχύ εξόδου
ραδιοσυχνοτήτων (RF) μικρότερη από
+5dBm
e.i.r.p. (ισοδύναμη ισοτροπικά
ακτινοβολούμενη ισχύς)
Dutch
Hierbij verklaart HID Global
dat deze radioapparatuur
modelnummer BEEKS001
in overeenstemming is met
Richtlijn 2014/53/EU. De
volledige tekst van de Europese
conformiteitsverklaring is te vinden
op de website: www.hidglobal/
certifications
Dit product werkt op de volgende
frequenties:
•2,4 GHz-band met een RF-
uitgangsvermogen van minder dan
+5 dBm e.i.r.p.
Danish
HID Global erklærer hermed, at
dette radioudstyr modelnummer
BEEKS001 er i overensstemmelse
med direktiv 2014/53/
EU. Den fulde tekst i EU-
overensstemmelseser- klæringen
kan læses her: www.hidglobal/
certifications
Dette produkt fungerer ved
følgende frekvenser:
•2,4 GHz-bånd med en RF-
udgangseekt på mindre end
+5dBm e.i.r.p.
Estonian
Käesolevaga kinnitab HID Global,
et see raadioseadmestik
mudelinumbriga BEEKS001 on
vastavuses direktiiviga 2014/53/EL.
Kogu EL-i vastavusdeklaratsiooni
tekst on saadaval järgmisel
internetiaadressil: www.hidglobal/
certifications
See toode töötab järgmistel
sagedustel.
•2,4 GHz ribalaiusel
raadiosagedusliku
väljundvõimsusega vähem kui +5
dBm e.i.r.p.
Maltese
Hawnhekk, HID Global tiddikjara
li dan it-Tagħmir tar-Radju bin-
numru tal-mudell BEEKS001
huwa konformi mad-Direttiva
2014/53/UE. It-test sħiħ tad-
dikjarazzjoni ta’ konformità tal- UE
hu disponibbli f’dan l- indirizz
fuq l-Internet: www.hidglobal/
certifications
Dan il-prodott jopera fil- frekwenzi
li eġjjin:
•2.4 GHz band b’RF output power
ta’ inqas minn +5 d Bm e.i.r.p.
German
Hiermit erklärt HID Global, dass
dieses Funkgerätmodell Nr.
BEEKS001 der Richtlinie
2014/53/EU entspricht. Der
vollständige Text der EU-
Konformitätserklärung steht unter
der folgenden Internetadresse zur
Verfügung:
www.hidglobal/certifications
Dieses Produkt arbeitet mit den
folgenden Frequenzen:
•2,4-GHz-Band mit einer HF-
Ausgangsleistung von weniger als
+5dBm EIRP
Finnish
HID Global vakuuttaa täten, että
tämä radiolaite, mallinumero
BEEKS001, vastaa direktiiviä
2014/53/EU. EU-
vaatimustenmukaisuus-
vakuutuksen koko teksti on
saatavissa seuraavasta Internet-
osoitteesta: www.hidglobal/
certiifcations
Tämä tuote toimii seuraavilla
taajuuksilla:
•2,4 GHz:n kaista, RF- lähtöteho
alle +5 dBm EIRP
Swedish
Härmed intygar HID Global
att denna radioutrustning
modell nummer BEEKS001
överensstämmer med direktiv
2014/53/EU. Den fullständiga
texten med intyg om
överensstämmelse för EU finns
på följande internetadress: www.
hidglobal/certifications
Den här produkten fungerar på
följande frekvenser:
•2,4 GHz-band med en RF-uteekt
på mindre än +5dBm e.i.r.p.
French
Par la présente, HID Global déclare
que cet équipement radio Modèle
BEEKS001 est conforme à la
directive 2014/53/UE. Le texte
intégral de la déclaration de
conformité de l’UE est disponible
sur le site Internet: www.hidglobal/
certifications
Ce produit fonctionne aux
fréquences suivantes:
•dans la bande de
2,4 GHz avec une puissance de
sortie RF inférieure à +5dBm PIRE
Italian
Con il presente documento, HID
Global dichiara che la presente
apparecchiatura radio modello
BEEKS001 è conforme alla direttiva
2014/53/UE. Il testo completo della
dichiarazione UE di conformità
è disponibile su Internet al
seguente indirizzo: www.hidglobal/
certifications
Questo prodotto funziona alle
seguenti frequenze:
•Banda a 2,4 GHz con potenza di
uscita RF inferiore a +5 dBm EIRP
Polish
Firma HID Global deklaruje
niniejszym, że to urządzenie
radiowe, model numer BEEKS001,
spełnia wymogi określone w
Dyrektywie 2014/53/UE. Pełny
tekst deklaracji zgodnocśi UE jest
dostpęny pod
nastpęujcąym adresem
internetowym: www.hidglobal/
certifications
Ten produkt działa na
nastpęujcąych czsętotliwocśiach:
•w paśmie 2,4 GHz z
równoważną mocą wyjściową RF
wypromieniowaną izotropowo
(EIRP) mniejszą niż +5dBm.
SRD Model: BEEKS001
RF Specifications
Standard Protocol: BLE 4.2
Frequency Band: 2400-2483.5 MHz
No of RF channels: 40
RF output power:+5dBm
Modulation: GFSK
ITU emissions code:1M03F1D
Antenna: PCB, 0 dBi
Communication Regulation
The following is a list that applies:
US FCC – United States Compliance
FCC ID: SL6-BEEKS001
This device complies with part 15 of the FCC
Rules. Operation is subject to the following
two conditions: (1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation.
IMPORTANT: Changes or modifications to this
product not authorized by HID, could void the
FCC Certification and negate your authority to
operate this product.
Note: This equipment has been tested and
found to comply with the limits for a class B
digital device, pursuant to part 15 of the FCC
rules.
Canada ISED – Canadian Compliance
24824-BEEKS001
This device complies with Industry Canada
license- exempt RSS standard(s). Operation is
subject to the following two conditions: (1) this
device may not cause interference, and (2) this
device must accept any interference, including
interference that may cause undesired
operation of the device.
Le présent appareil est conforme aux CNR
d’Industrie Canada applicables aux appareils
radio exempts de licence. L’exploitation est
autorisée aux deux conditions suivantes : (1)
l’appareil ne doit pas produire de brouillage,
et (2) l’appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage
est susceptible d’en compromettre le
fonctionnement.
ENACOM-Argentina Compliance
CNC ID: C-24005
This product conforms to Argentina Radio
Requirements.
Este producto cumple con los requisitos de
Argentina relative a la radioelectricidad
Australia/ New Zealand Compliance
This product conforms to Australia and New
Zealand Radio Requirements.
European Union Compliance
Conformite Européenne (European
Community)
Hereby, HID Global declares that this Radio
Equipment SRD Model number BEEKS001 is in
compliance with Directive 2014/53/EU.
The full text of the EU declaration of
conformity is available at the following
internet address: www.hidglobal/certifications
This product operates at the following
frequencies:
2.4 GHz band with an RF output power of
less than +5dBm e.i.r.p
HID® BEEKS001 Install Guide PLT-05252, Rev. A.1 INSTALLATION GUIDE
hidglobal.com An ASSA ABLOY Group brand
4Regulation Information For more detailed information, visit https://hid.gl/HID-BEEKs-installation
Croatian
Ovime tvrtka HID Global izjavljuje da je
ova radijska oprema model BEEKS001
u skladu s Direktivom 2014/53/EU.
Cjelokupan tekst europske izjave o
sukladnosti dostupan je na sljedećoj
internetskoj stranici: www.hidglobal/
certications
Ovaj proizvod radi pri sljedećim
frekvencijama:
•pri frekvenciji od 2,4 GHz s izlaznom
RF snagom manjom od +5dBm e.i.r.p
Lithuanian
Šiuo „“ deklaruoja, kad šis radijo
įrangos modeHID Global lis, kurio
numeris BEEKS001, atitinka Direktyvą
2014/53/EB. Visą ES atitikties
deklaracijos tekstą galite rasti šiuo
interneto adresu: www.hidglobal/
certications
Šis gaminys veikia tokiais dažniais:
•2,4 GHz dažnio diapazonas, RD
išvesties galia yra mažesnė nei +5
dBm EIRP.
Slovenian
Družba HID Global izjavlja, da je ta
radijska oprema, številka modela
BEEKS001, v skladu z Direktivo
2014/53/EU. Celotno besedilo
izjave EU o skladnosti je na voljo na
naslednjem spletnem naslovu: www.
hidglobal/certications
Ta izdelek deluje pri naslednjih
frekvencah:
•2,4 GHz z izhodno
močjo RF manj kot +5dBm
e.i.m.o. (EIRP)
Hungarian
A HID Global ezúton nyilatkozza,
hogy ez az BEEKS001 típusszámú
rádióberendezés megfelel a 2014/53/
EU irányelvnek. Az EU megfelelőségi
nyilatkozat teljes szövege elérhető
a következő internetes címen: www.
hidglobal/certications
A termék a következő frekvenciákon
üzemel:
•2,4 GHz-es sáv, mely esetében RF
kimeneti teljesítménye kevesebb, mint
+5 dBm EIRP
Latvian
Ar šo uzņēmums HID Global apliecina,
ka šī radioiekārta, modeļa numurs
BEEKS001, atbilst Direktīvas 2014/53/
ES prasībām. Pilnu ES atbilstības
deklarācijas tekstu var skatīt vietnē
www.hidglobal/certications
Šis izstrādājums darbojas ar šādām
frekvencēm:
•2,4 GHz josla; radiofrekvences
izvades jauda ir mazāka par +5 dBm
(ekvivalentā izotropiski izstarotā jauda).
Slovak
Spoločnosť HID Global týmto
vyhlasuje, že toto rádiové zariadenie,
model BEEKS001, je v súlade so
smernicou 2014/53/EÚ. Úplné znenie
vyhlásenia o zhode so smernicami
EÚ je k dispozícii na stránke: www.
hidglobal/certications
Toto zariadenie pracuje pri
nasledujúcich frekvenciách:
•2,4 GHz pásmo s RF výstupným
výkonom nižším ako +5dBm EIRP
Romanian
Prin prezenta, HID Global declară că
acest echipament radio număr model
BEEKS001 ste în conformitate cu
Directiva 2014/53/UE. Textul complet al
declarației de conformitate UE poate
gsăit la urmtăoarea adresăde internet:
www.hidglobal/certications
Acest produs funcționeazăla
urmtăoarele frecvențe:
•în banda 2,4 GHz cu o putere de ieșire
RF de mai puțin de +5dBm E.I.R.P.
Portuguese
Por este meio, a HID Global declara
que este modelo de equipamento de
rádio, número BEEKS001, está em
conformidade com a Diretiva 2014/53/
UE. O texto completo da declaração de
conformidade da UE está disponível no
seguinte endereço da Internet: www.
hidglobal/certications
Este produto opera nas frequências
seguintes:
•2,4 GHz com uma potência de saída
de RF inferior a +5dBm e.i.r.p.
Spanish
Por la presente, HID Global declara
que este equipo de radio, modelo
número BEEKS001 cumple la Directiva
2014/53/EU. El texto completo de la
Declaración de Conformidad CE está
disponible en la siguiente dirección de
internet: www.hid global/certications
Este producto opera en las siguientes
frecuencias:
•Banda de frecuencia de 2,4 GHz con
una potencia de salida de RF (PIRE)
de menos de +5dBm.
Anatel – Brazil Compliance
06515-19-12446
Este produto está homologado pela ANATEL, de acordo com os procedimentos regulamentados
pela Resolução 242/2000, e atende aos requisitos técnicos aplicados. Para maiores informações,
consulte o site da ANATEL - www.anatel.gov.br
This product is homologated at ANATEL according to procedure regulated by Resolution
242/2000, and it complies with the applicable technical requirements. For more information,
consult ANATEL website - www.anatel.gov.br
IFETEL – Mexico Compliance
IFT:RCPBLBE19-1936
China- SRRC Compliance
CMIIT- XXYYZZZZ (in process)
Japan- Placeholder
Russia Compliance
Этот передатчик должен быть установлен и эксплуатироваться таким образом, чтобы расстояние
между излучателем и вашим телом составляло не менее 20 см. Его также нельзя располагать рядом
с любой другой антенной или передатчиком или эксплуатировать совместно с такой антенной или
передатчиком.
Pегуляция
(FSS) Д-ИВРД-6322
-
1
-
2
-
3
-
4
-
5
in altre lingue
- English: HID BEEKS001 Installation guide
- eesti: HID BEEKS001 paigaldusjuhend
- română: HID BEEKS001 Ghid de instalare
Documenti correlati
Altri documenti
-
Axis A1001 Manuale utente
-
Harman Kardon CITATION RECEIVER Manuale utente
-
ZyXEL WAP6906 Manuale utente
-
-
-
Yamaha Video Sound Collaboration System for Huddle Rooms [CS-700] Manuale utente
-
Elo 22-inch Guida utente
-
Harman Kardon Citation 100 Manuale del proprietario
-
Watchguard AP420 Guida Rapida