Husqvarna 533RS Manuale utente

533RS, 543RS, 553RS

EN Operator's manual 2-32

ES Manual de usuario 33-64

PT Manual do utilizador 65-95

IT Manuale dell'operatore 96-126

Contents

Introduction..................................................................... 2

Safety..............................................................................4

Assembly...................................................................... 11

Operation...................................................................... 15

Maintenance................................................................. 22

Troubleshooting............................................................ 27

Transportation and storage...........................................28

Technical data.............................................................. 28

Accessories.................................................................. 29

Declaration of Conformity............................................. 31

Appendix ....................................................................127

Introduction

Product description

This product is a brushcutter with a combustion engine.

Work is constantly in progress to increase your safety

and efficiency during operation. Speak to your servicing

dealer for more information.

Intended use

Use the product with a saw blade, a grass blade or a

trimmer head to cut different types of vegetation. Do

not use the product for other tasks than grass trimming,

grass clearing and forestry clearing. Use a saw blade to

cut fibrous types of wood. Use a grass blade or trimmer

head to cut grass.

Note: National or local regulations can regulate the

use. Comply to given regulations.

Only use the product with accessories that are approved

by the manufacturer. Refer to .

Product overview

11

1

3

2

4

10

12

13

15

16

17

18

19 20

22

23

24

29

30

25

9

8

76

21

5

1

27

14

26

28

13

12

11

27 14

543RS, 553RS

533RS

1. Blade

2. Grease filler cap, bevel gear

3. Bevel gear

4. Cutting attachment guard

5. Shaft

6. Start throttle button

7. Stop switch

8. Throttle control

21756 - 001 - 08.06.2022

9. Throttle lockout

10. Suspension ring

11. Cylinder cover

12. Starter rope handle

13. Fuel tank

14. Choke control

15. Air filter cover

16. Handlebar

17. Clutch cover

18. Locknut

19. Support flange

20. Support cup

21. Handlebar clamp

22. Operator's manual

23. Transport guard

24. Socket wrench

25. Locking pin

26. Harness

27. Air purge bulb

28. Guard extension

29. Trimmer head

30. Screwdriver

Symbols on the product

WARNING: This product can be

dangerous and cause serious injury or

death to the operator or others. Be careful

and use the product correctly.

Read the operator's manual carefully

and make sure that you understand the

instructions before use.

Use a protective helmet in locations where

objects can fall on you. Use approved

hearing protection and approved eye

protection.

Maximum speed of the output shaft.

The product agrees with the applicable

EC directives.

This product conforms to the applicable

UK regulations.

The product can cause objects to eject,

which can cause injury.

50FT

15 m

50FT

15 m

Keep a minimum distance of 15 m / 50 ft.

to persons and animals during operation

of the product.

Risk of blade thrust if the cutting

equipment touches an object that it does

not immediately cut. The product can cut

off body parts. Keep a minimum of 15

m / 50 ft. distance to persons and animals

during operation of the product.

The arrows shows the limit for the handle

position.

Choke.

Air purge bulb.

Hot surface.

Use approved protective gloves.

Use heavy-duty slip-resistant boots.

Noise emissions to the environment

label as per EU and UK directives

and regulations, and New South Wales

legislation "Protection of Environment

Operations (Noise Control) Regulation

2017". The guaranteed sound power level

of the product is specified in

Technical

data on page 28

.

yyyywwxxxx

The rating plate or the laser printing

shows the serial number. yyyy is the

production year and ww is the pro-

duction week.

Note: Other symbols/decals on the product refer to

certification requirements for other commercial areas.

1756 - 001 - 08.06.2022 3

Euro V Emissions

WARNING: Tampering with the engine

voids the EU type-approval of this product.

Product liability

As referred to in the product liability laws, we are not

liable for damages that our product causes if:

• the product is incorrectly repaired.

• the product is repaired with parts that are not

from the manufacturer or not approved by the

manufacturer.

• the product has an accessory that is not from the

manufacturer or not approved by the manufacturer.

• the product is not repaired at an approved service

center or by an approved authority.

Safety

Safety definitions

Warnings, cautions and notes are used to point out

specially important parts of the manual.

WARNING: Used if there is a risk of

injury or death for the operator or bystanders

if the instructions in the manual are not

obeyed.

CAUTION: Used if there is a risk of

damage to the product, other materials or

the adjacent area if the instructions in the

manual are not obeyed.

Note: Used to give more information that is necessary

in a given situation.

General safety instructions

WARNING: Read the warning

instructions that follow before you use the

product.

• Do not do changes to the product without approval

from the manufacturer and always use original

accessories. Not approved modifications and/or

accessories can result in serious injury or the death

of the operator or others.

• The inner side of the muffler contains chemicals that

may be carcinogenic. Do not touch the muffler if it is

damaged.

• This product produces an electromagnetic field

during operation, which can cause interference with

medical implants. This can cause serious injury or

death. Speak to your physician and the medical

implant manufacturer before use.

• Do not touch the spark plug or spark plug cord when

the engine is on. Risk of electrical shock.

• Your warranty may not be approved for damages

caused by accessories or spare parts that are not

approved.

Safety instructions for assembly

WARNING: Read the warning

instructions that follow before you use the

product.

• Remove the spark plug cap from the spark plug

before you assemble the product.

• Use approved protective gloves.

• Make sure that you assemble the cover and shaft

correctly before you start the engine.

• The drive disc and support flange must engage

correctly in the center hole of the cutting attachment.

A cutting attachment that is attached incorrectly can

cause serious injury or death of the operator or

others.

• To operate the product safely and prevent injury

to the operator or other persons, the product must

always be attached correctly to the harness.

Safety instructions for operation

WARNING: Read the warning

instructions that follow before you use the

product.

• You must understand the difference between grass

clearing and grass trimming before use.

• If you encounter a situation where you are uncertain

how to proceed you should ask an expert. Contact

your dealer or your service workshop. Avoid all

usage which you consider to be beyond your

capability.

• Never use a product that is faulty. Carry out the

safety checks, maintenance and service instructions

described in this manual. Some maintenance and

service measures must be carried out by trained and

qualified specialists. See instructions under

Safety

devices on the product on page 6

• All covers, guards and handles must be fitted before

you start the product. Ensure that the spark plug cap

and ignition lead are undamaged to avoid the risk of

electric shock.

• Never use the product if you are fatigued, while

under the influence of alcohol or drugs, medication

41756 - 001 - 08.06.2022

or anything that could affect your vision, alertness,

coordination or judgement.

• Do not use the product in bad weather such

as dense fog, heavy rain, strong wind, intense

cold, etcetera. Working in bad weather is tiring

and often brings added risks, such as icy ground,

unpredictable felling direction, etcetera.

• The only accessories you can operate with this

engine unit are the cutting attachments that we

recommend in the chapter

Accessories 533RS on

page 30

.

• Never allow children to use or be in the vicinity of the

product. As the product is equipped with a spring-

loaded start/stop switch and can be started by low

speed and force on the starter handle, even small

children under some circumstances can produce the

force necessary to start the product. This can mean

a risk of serious personal injury. Therefore remove

the spark plug cap when the product is not under

close supervision.

• Running an engine in a confined or badly ventilated

area can result in death due to asphyxiation or

carbon monoxide poisoning.

• The complete clutch cover and shaft must be fitted

before the product is started, otherwise the clutch

can come loose and cause personal injury.

• Ensure that no people or animals come closer than

15 metres while you work. When several operators

are working in the same area the safety distance

should be at least 15 metres. Otherwise there is

a risk of serious personal injury. Stop the product

immediately if anyone approaches. Never swing the

product around without first checking behind you to

make sure that noone is within the safety zone.

• Ensure that people, animals or other things can

not affect your control of the product or that they

do not come in contact with the cutting attachment

or loose objects that are thrown out by the cutting

attachment. However, do not the product unless you

are able to call for help in the event of an accident.

• Always inspect the working area. Remove all loose

objects such as stones, broken glass, nails, steel

wire, string, etcetera, that could be thrown out or

become wrapped around the cutting attachment.

• Make sure that you can move and stand safely.

Check the area around you for possible obstacles

(roots, rocks, branches, ditches, etcetera) in case

you have to move suddenly. Take great care when

you work on sloping ground.

• Keep a good balance and a firm foothold at all times.

Do not overreach.

• Always hold the product with both hands. Hold the

product on the right side of your body.

• Always use the harness. Make sure that you

attach the harness to the suspension ring.

• Keep the cutting attachment below waist level.

• Switch off the engine before you move to another

area. Fit the transportation guard before you carry or

transport the equipment any distance.

• Never put the product down with the engine running

unless you have it in clear sight.

• Stop the engine and cutting equipment before you

remove material that has wound around the blade

shaft. Neither the operator of the product nor anyone

else may attempt to remove the cut material while

the engine is running or the cutting equipment is

rotating, as this can result in serious injury. The

bevel gear can get hot during use and may remain

so for a while afterwards. You could get burnt if you

touch it.

• Watch out for thrown objects. Always wear

approved eye protection. Never lean over the cutting

attachment guard. Stones, rubbish, etcetera, can be

1756 - 001 - 08.06.2022 5

thrown up into the eyes which can cause blindness

or serious injury.

• Sometimes branches or grass get caught between

the guard and cutting attachment. Always stop the

engine before you clean the product.

• Products that are fitted with saw blades or grass

blades can be thrown violently to the side when

the blade comes into contact with a fired object.

This is called blade thrust. A blade thrust can be

violent enough to cause the product and/or operator

to be propelled in any direction, and possibly lose

control of the product. Blade thrust can occur without

warning if the product snags, stalls or binds. Blade

thrust is more likely to occur in areas where it is

difficult to see the material being cut.

• Avoid to cut with the area of the blade between the

12 o'clock and 3 o'clock positions. Because of the

speed of rotation of the blade, blade thrust can occur

if you attempt to cut thick stems with this area of the

blade.

• Always slow the engine to idle speed after each

working operation. Long periods at full throttle

without any load on the engine can lead to serious

engine damage.

• Listen out for warning signals or shouts when

you wear hearing protection. Always remove your

hearing protection as soon as the engine stops.

• Overexposure to vibration can lead to circulatory

damage or nerve damage in people who have

impaired circulation. Contact your doctor if you

experience symptoms of overexposure to vibration.

These symptoms include numbness, loss of feeling,

tingling, pricking, pain, loss of strength, changes in

skin colour or condition. These symptoms normally

appear in the fingers, hands or wrists.

• Do not use a product with a damaged spark plug

cap.

• Do not use a product with a defective muffler.

• Keep all parts of your body away from the rotating

cutting attachment and hot surfaces.

• Always wear gloves when you handle the grass

blade.

Personal protective equipment

WARNING: Read the warning

instructions that follow before you use the

product.

• Always use approved personal protective equipment

when you use the product. Personal protective

equipment cannot fully prevent injury but it

decreases the degree of injury if an accident does

occur. Let your dealer help you select the right

equipment.

• Use a protective helmet where there is a risk of

falling objects.

• Use approved hearing protection that provides

adequate noise reduction. Long-term exposure to

noise can result in permanent hearing impairment.

• Use approved eye protection. If you use a visor,

you must also use approved protective goggles.

Approved protective goggles must comply with the

ANSI Z87.1 standard in the USA or EN 166 in EU

countries.

• Use a visor for face protection. A visor is not enough

for protection of the eyes.

+

• Use gloves when necessary, for example when you

attach, examine or clean the cutting equipment.

• Use sturdy non-slip boots.

• Use clothing made of a strong fabric. Always use

heavy, long pants and long sleeves. Do not use

loose clothing that can catch on twigs and branches.

Do not wear jewelry, short pants, sandals or go with

bare feet. Put your hair up safely above shoulder

level.

• Keep first aid equipment close at hand.

Safety devices on the product

For information about where to find the safety devices,

see

Product overview on page 2

.

WARNING: Read the warning

instructions that follow before you use the

product.

• Do not use a product with defective safety devices.

Do a check of and do maintenance on the safety

devices regularly. If the safety devices are defective,

speak to your Husqvarna service agent.

• Do not make changes to safety devices. Do not

use the product if protective covers, safety switches

or other protective devices are not attached or are

defective.

• For all service and repair work on the product,

especially for the safety devices, special training is

necessary. If the safety devices fail the checks given

in this operator's manual, you must let a service

agent help you. We guarantee that professional

61756 - 001 - 08.06.2022

repairs and service is available. If your dealer is not

a service agent, speak to them for information about

the nearest service agent.

• Do not use a cutting attachment without an approved

and correctly attached cutting attachment guard.

See .

To do a check of the throttle trigger lockout

1. Make sure that the throttle trigger lockout (A) and

throttle trigger (B) move freely and that the return

spring operates correctly.

A

B

2. Push down the throttle trigger lockout and make

sure that it goes back to its initial position when you

release it.

3. Make sure that the throttle trigger is locked at the

idle position when the throttle trigger lockout is

released.

4. Start the product and apply full throttle.

5. Release the throttle trigger and make sure that the

cutting attachment stops and stays stationary.

WARNING: If the cutting

attachment moves when the throttle

trigger is in the idle position, then the

carburetor idle speed must be adjusted.

Refer to

To adjust the idle speed

(533RS) on page 23

.

To do a check of the stop switch

1. Start the engine.

2. Move the stop switch to the stop position and make

sure that the engine stops.

To do a check of the cutting attachment guard

The cutting attachment guard prevents injuries and

stops objects that eject in the direction of the operator.

1. Stop the engine.

2. Do a visual check for damages, for example cracks.

3. Replace the cutting attachment guard if it is

damaged.

To do a check of the vibration damping system

WARNING: Use of an incorrect cutting

attachment increases the level of vibration.

The vibration damping system decreases vibration in the

handles to a minimum. The vibration damping system

1756 - 001 - 08.06.2022 7

decreases the vibrations between the engine unit and

the shaft unit.

1. Stop the engine.

2. Do a visual check for deformation and damage, for

example cracks.

3. Make sure that the vibration damping units are

attached correctly.

To do a check of the quick-release mechanism

WARNING: Do not use a harness with

a defective quick-release mechanism.

The quick-release mechanism lets the operator remove

the product quickly from the harness if there is an

emergency.

1. Stop the engine.

2. Do a visual check for damage, for example cracks.

3. Release and attach the quick-release mechanism to

make sure that it operates correctly.

To do a check of the muffler

WARNING: Never use a product with a

faulty muffler.

WARNING: Bear in mind that the

exhaust fumes from the engine are hot and

may contain sparks which can start a fire.

Never start the product indoors or near

combustible material!

The muffler keeps noise levels to a minimum and sends

exhaust fumes away from the operator. For mufflers it is

very important that you follow the instructions on how to

check, maintain and service your product.

Regularly check that the muffler is securely attached to

the product.

To attach and remove the locknut

WARNING: Stop the engine, use

protective gloves and be careful around the

sharp edges of the cutting attachment.

A locknut is used to attach some types of cutting

attachments. The locknut has a left thread.

• To attach, tighten the locknut in the opposite

direction to the direction of turning of the cutting

attachment.

• To remove the locknut, loosen the locknut in the

same direction as the cutting attachment rotates.

81756 - 001 - 08.06.2022

• To loosen and tighten the locknut, use a socket

wrench with a long shaft. The arrow in the picture

shows the area where you can operate the socket

wrench.

WARNING: When you loosen and

tighten the locknut, there is a risk of

injury from the blade. You must always

make sure that the blade guard prevents

injury to your hand when you do this.

Note: Make sure that you can not turn the locknut by

hand. Replace the nut if the nylon lining does not have

a resistance of a minimum of 1.5 Nm. The locknut must

be replaced after it has been put on approximately 10

times.

Cutting equipment

Choose and maintain the cutting equipment to:

• Obtain maximum cutting performance.

• Increase life span of the cutting equipment.

• Follow the checking, maintenance and service

instructions for the muffler.

• Always use the recommended guard for the cutting

equipment. See Technical data.

WARNING: Only use cutting

attachments with the guards we

recommend! See the chapter on Technical

data. Refer to the instructions for the cutting

attachment to check the correct way to load

the trimmer line and the correct trimmer line

diameter.

WARNING: A faulty cutting attachment

may increase the risk of accidents.

WARNING: Always stop the engine

before doing any work on the cutting

attachment. This continues to rotate even

after the throttle has been released. Ensure

that the cutting attachment has stopped

completely and disconnect the spark plug

cap before you start to work on it.

Cutting equipment

• Use the blades to cut wood.

• Use the blades and grass knives to cut coarse grass.

• Use the trimmer head to cut grass.

• An incorrectly sharpened or damaged blade

increases the risk of accidents. Keep the teeth of the

blade correctly sharpened. Follow the instructions in

To sharpen grass cutters and grass blades on page

26

and use the recommended file gauge.

• Examine the cutting equipment for damage and

cracks. Replace the cutting equipment if it is

damaged.

• Only use the cutting equipment with the

recommended guards. Refer to

Accessories on page

29

.

Trimmer head

WARNING: Always make sure that

the trimmer line is wound tightly and

equally around the drum to prevent harmful

vibration.

1756 - 001 - 08.06.2022 9

• Only use recommended cutting attachments.

• The length of the trimmer line is important. For a

longer trimmer line, more engine power is necessary

than for a shorter trimmer line of the same diameter.

• Do not move the installation position of the trimmer

guard.

• Make sure that the cutter on the trimmer guard is

not damaged. The cutter cuts the trimmer line to the

correct length.

• Soak the trimmer line for 2 days before use, to

increase its life length.

Grass blades and grass cutters

• Use the product with an approved grass blade. Do

not use a grass blade without proper installation of

all required parts. Make sure that the installation is

done correctly and that the proper parts are used.

Improper installation may cause the blade to fly off

and seriously injure the operator or the bystanders.

• Wear protective gloves when you handle or do

maintenance on the blade.

• Use head protection when you operate a product

with a grass blade.

• Grass blades and grass cutters are used to cut

rough grass.

• A grass blade can cause injury while it continues

to spin after the engine is stopped or the throttle

trigger is released. Make sure that the grass

blade has completely stopped rotating before any

maintenance.

• Stop the engine before you do work on the cutting

attachment. Make sure the cutting attachment fully

stops. Disconnect the lead from the spark plug.

• Only use an approved cutting attachment or a

correctly sharpened blade.

• Keep the teeth of the blade correctly sharpened.

• Do not use a damaged cutting attachment.

• Attach the transport guard to the grass blade when

you transport or store the product.

Blade thrust

• A blade thrust is a sudden movement of the product

to the side, forward or rearward. A blade thrust

occurs when the grass blade hits an object that

cannot be cut. In areas where it is not easy to

see the material being cut the risk of blade thrust

increases.

• When a blade thrust occurs, there is a risk that the

product or the operator moves out of position. A

blade that moves can hit bystanders and there is a

risk of injuries.

• If a blade is bent, has cracks, is broken or damaged,

discard the blade.

• Use a sharp blade. The risk of blade thrust increases

when a blade is not sharp.

Fuel safety

• Do not start the product if there is fuel or engine oil

on the product. Remove the unwanted fuel/oil and

let the product dry. Remove unwanted fuel from the

product.

• If you spill fuel on your clothing, change clothing

immediately.

• Do not get fuel on your body, it can cause injury. If

you get fuel on your body, use a soap and water to

remove the fuel.

• Do not start the engine if you spill oil or fuel on the

product or on your body.

• Do not start the product if the engine has a leak.

Examine the engine for leaks regularly.

• Be careful with fuel. Fuel is flammable and the fumes

are explosive and can cause injuries or death.

• Do not breathe in the fuel fumes, it can cause injury.

Make sure that there is a sufficient airflow.

• Do not smoke near the fuel or the engine.

• Do not put warm objects near the fuel or the engine.

• Do not add the fuel when the engine is on.

• Make sure that the engine is cool before you refuel.

• Before you refuel, open the fuel tank cap slowly and

release the pressure carefully.

• Do not add fuel to the engine in an indoor area. Not

sufficient airflow can cause injury or death because

of asphyxiation or carbon monoxide.

• Tighten the fuel tank cap carefully or a fire can

occur.

• Move the product at a minimum of 3 m (10 ft) from

the position where you filled the tank before a start.

• Do not put too much fuel in the fuel tank.

• Make sure that a leak cannot occur when you move

the product or fuel container.

• Do not put the product or a fuel container where

there is an open flame, spark or pilot light. Make

sure that the storage area does not contain an open

flame.

• Only use approved containers when you move the

fuel or put the fuel into storage.

• Empty the fuel tank before long-term storage. Obey

the local law on where to dispose fuel.

• Clean the product before long-term storage.

• Remove the spark plug cable before you put the

product into storage to make sure that the engine

does not start accidentally.

10 1756 - 001 - 08.06.2022

Safety instructions for maintenance

WARNING: Read the warning

instructions that follow before you use the

product.

• Stop the engine, make sure that the cutting

attachment stops and let the product cool down

before you do the maintenance.

• Disconnect the spark plug cap before you do the

maintenance.

• The exhaust fumes from the engine contain

carbon monoxide, an odorless, poisonous and very

dangerous gas that can cause death. Do not run the

product indoors or in closed spaces.

• The exhaust fumes from the engine are hot and can

contain sparks. Do not run the product indoors or

near flammable material.

• Accessories and changes to the product that are not

approved by the manufacturer, can cause serious

injury or death. Do not change the product. Always

use original accessories.

• If the maintenance is not done correctly and

regularly, there is an increased risk of injury and

damage to the product.

• Only do the maintenance as this operator's manual

recommends. Let an approved Husqvarna service

agent do all other servicing.

• Let an approved Husqvarna service agent do

servicing on the product regularly.

• Replace damaged, worn or broken parts.

Assembly

WARNING: Read the safety chapter

before you assemble the product.

Introduction

WARNING: Before you assemble the

product, you must read and understand the

safety chapter.

WARNING: Remove the spark plug

cable from the spark plug before you

assemble the product.

To install the handlebar

1. Install the handlebar in the handlebar clamp on the

shaft.

2. Install the protective sleeve.

To install blades and trimmer heads

WARNING: Only use the approved

guard for the blades. See

Technical data

on page 28

. A defective guard can cause

injury.

WARNING: If you operate the product

with a grass blade, first install the correct

handlebar, blade guard and harness .

WARNING: If you do not install the the

blades correctly, it can cause injury.

1756 - 001 - 08.06.2022 11

1. Make sure that the lifted section on the drive disc/

support flange engages correctly in the center hole

of the blades.

2. Install the blades.

To attach and remove the guard extension

The guard extension is used on the cutting attachment

guard. Attach the guard extension when you use a

trimmer head or plastic blades. Remove the extension

guard when you use a grass blade.

• Put the guide on the guard extension into the slot

on the cutting attachment guard. Lock the 4 locking

hooks into position.

• Release the locking hooks with a screwdriver to

remove the guard extension.

To install the blade guard

CAUTION: Only use the approved

guard for the blades. Refer to

Technical data

on page 28

.

1. Remove the bracket (H).

2. Attach the adapter (I) and bracket (J) with the 2

screws (K).

3. Attach the blade guard (A) to the adapter with the 4

screws (L).

J K

I

L

A

H

To install the saw blade

WARNING: There is a risk of injury

around the saw blade nut. Make sure that

the blade guard is correctly installed. Always

use protective gloves.

1. Attach the drive disc (B) to the output shaft.

2. Turn the blade shaft until one of the holes in the

drive disc aligns with the hole in the gear housing.

3. Put the locking pin or hex key (C) in the hole to lock

the shaft.

4. Install the saw blade (D) and the support flange (F)

to the output shaft.

5. Install the saw blade nut (G).

Note: The saw blade nut has a left hand thread.

6. Turn the socket wrench counterclockwise to tighten

the locknut. Make sure that the torque of the locknut

is 35-50 Nm (3.5-5 kpm). Hold the shaft of the socket

wrench as near the blade guard as possible.

GF

D

B

C

12 1756 - 001 - 08.06.2022

a) Make sure that you operate the socket wrench in

the identified area when you loosen or tighten the

saw blade nut.

To install the cutting attachment guard and the

grass blade (533RS)

1. Put the cutting attachment guard (A) onto the shaft

and tighten the bolt (B) to attach it.

A

B

2. Turn the output shaft to align 1 of the holes in

the drive disc (C) with the related hole in the gear

housing.

H

G

F

E

C

D

3. Put the locking pin (D) in the hole to lock the shaft.

4. Put the grass blade (E), the support cup (F) and the

support flange (G) on the output shaft.

5. Make sure that the drive disc and support flange

engages correctly in the center hole of the grass

blade.

6. Attach the nut (H).

7. Tighten the nut to the support flange with the socket

wrench. Hold the shaft of the socket wrench near the

blade guard. Tighten in the opposite direction to how

the cutting attachment rotates. Tighten it to a torque

of 35-50 Nm.

1756 - 001 - 08.06.2022 13

To install the cutting attachment guard and the

grass blade (543RS, 553RS)

1. Put the cutting attachment guard (A) onto the shaft

and tighten the bolt (B) to attach it.

B

A

2. Turn the output shaft to align 1 of the holes in

the drive disc (C) with the related hole in the gear

housing.

H

G

F

C

D

E

3. Put the locking pin (D) in the hole to lock the shaft.

4. Put the grass blade (E), the support flange (F) and

the support cup (G) on the output shaft.

5. Make sure that the drive disc and support flange

engages correctly in the center hole of the grass

blade.

6. Install the nut (H).

7. Tighten the nut to the support flange with the socket

wrench. Hold the shaft of the socket wrench near the

blade guard. Tighten in the opposite direction to how

the cutting attachment rotates. Tighten it to a torque

of 35-50 Nm.

To install the trimmer guard and the trimmer

head

Note: Make sure to use the correct trimmer guard for

the correct trimmer head.

1. Attach the trimmer guard (A) on the 2 hooks on the

plate holder (B).

2. Install the trimmer guard on the shaft and tighten it

with the bolt (C). Use the locking pin or a hex key (D)

to tighten the bolt.

A

E

G

BC

A

B

C

D

F

Note: Put the locking pin or a hex key in the

groove in the bolt head.

3. Put the drive disc (E) and the support flange (F) on

the output shaft.

4. Turn the output shaft until one of the holes in the

drive disc aligns with the hole in the gear housing.

5. Put the locking pin or a hex key in the hole to lock

the shaft.

14 1756 - 001 - 08.06.2022

6. Put a trimmer head or plastic blades on the output

shaft. Turn the trimmer head or plastic blades

counterclockwise to install.

7. To remove, follow the instructions in the opposite

sequence.

To install the transport guard

1. Install the blade in the transport guard (A).

2. Put the two fasteners (B) into the slots (C) to attach

the transport guard.

B

A

C

To adjust the harness

WARNING: The product must always

be correctly attached to the harness. Do not

use a defective harness.

1. Put on the harness.

2. Connect the product to the harness.

3. Adjust the harness for the best work position.

4. Adjust the side straps to make the product weigh

equally on your shoulders.

5. Adjust the harness until the cutting attachment is

parallel to the ground.

6. Let the cutting attachment lightly touch the ground.

Adjust the harness clamp to balance the product

correctly.

Note: If you use a grass blade, it must balance

approximately 10 cm /4 in above the ground.

Operation

WARNING: Read and understand the

safety chapter before you operate the

product.

Introduction

WARNING: Before you operate the

product, you must read and understand the

safety chapter.

Fuel

To use fuel

CAUTION: This product has a two-

cycle engine. Use a mixture of gasoline

and two-cycle engine oil. Make sure to use

the correct quantity of oil in the mixture.

Incorrect ratio of gasoline and oil can cause

damage to the engine.

Husqvarna alkylate fuel

We recommend you to use Husqvarna alkylate fuel for

best performance. The fuel contains less dangerous

material compared to regular fuel, which decreases

dangerous exhaust fumes. The fuel gives a low quantity

of dangerous remainings when it is combusted, which

keeps the components of the engine more clean. This

extends the life of the engine. Husqvarna alkylate fuel is

not available in all markets.

Gasoline

CAUTION: Do not use gasoline with an

octane number less than 90 RON (87 AKI).

This can cause damage to the product.

CAUTION: Do not use gasoline with

more than 10% ethanol concentration (E10).

This can cause damage to the product.

1756 - 001 - 08.06.2022 15

CAUTION: Do not use leaded gasoline.

This can cause damage to the product.

• Always use new unleaded gasoline with a minimum

octane number of 90 RON (87 AKI) and with less

than 10% ethanol concentration (E10).

• Use gasoline with a higher octane number if you

frequently use the product at continuously high

engine speed.

• Always use a good quality unleaded gasoline/oil

mixture.

Two-stroke oil

• For best results and performance use Husqvarna

two-stroke oil.

• If Husqvarna two-stroke oil is not available, use a

two-stroke oil of good quality for air-cooled engines.

Speak to your servicing dealer to select the correct

oil.

CAUTION: Do not use two-stroke

oil for water-cooled outboard engines,

also referred to as outboard oil. Do not

use oil for four-stroke engines.

To mix gasoline and two-stroke oil

CAUTION: There is a risk that small

errors influence the ratio of the mixture

drastically when you mix small quantities of

fuel. Carefully measure the quantity of oil

to be mixed to make sure that you get the

correct mixture.

1. Fill half the quantity of the gasoline to be used.

2. Add the full quantity of oil and mix (shake) the fuel

mixture.

3. Add the remaining quantity of gasoline.

4. Carefully mix (shake) the fuel mixture and fill the fuel

tank of the product.

5. Empty and clean the fuel tank if you do not use the

product for some time.

Note: Do not mix fuel for more than 1 month at a time

and always mix gasoline and oil in a clean container

intended for fuel.

To add fuel

WARNING: Do not smoke or put hot

objects near fuel. Before you add fuel, stop

the engine and let it cool for minutes.

WARNING: When you add fuel, open

the fuel tank cap slowly to release unwanted

pressure.

WARNING: After you add fuel, tighten

the fuel tank cap carefully. Move the

machine away from the refuelling area and

the power before you start the engine.

• Always use a fuel container with an anti-spill valve.

• Make sure that the area near the fuel tank cap

is clean. Contamination in the tank can cause

operating problems.

• Shake the fuel container before you add the fuel

mixture to the fuel tank.

To start and stop

Before you operate the product

• Examine the work area to make sure that you know

the type of terrain, the slope of the ground and if

there are obstacles such as stones, branches and

ditches.

• Do an overhaul inspection of the product.

• Do the safety inspections, maintenance and

servicing that are given in this manual.

• Make sure that all covers, guards, handles and the

cutting equipment are correctly attached and not

damaged.

• Make sure that there are no cracks at the bottom of

the grass blade teeth or by the center hole of the

blade. Replace the blade if it is damaged.

16 1756 - 001 - 08.06.2022

• Examine the support flange for cracks. Replace the

support flange if it is damaged.

• Make sure that the locknut can not be removed by

hand. If you can remove it by hand, it does not

lock the cutting attachment sufficiently and you must

replace it.

• Examine the blade guard for damages or cracks.

Replace the blade guard if it has been hit or if it has

cracks.

• Examine the trimmer head and cutting attachment

guard for damages or cracks. Replace the trimmer

head and cutting attachment guard if they have been

hit or if they have cracks.

To start the product (533RS)

1. Move the stop switch to the start position.

2. Push the air purge bulb until fuel starts to fill the air

purge bulb.

3. Move the choke control to the choke position.

4. Hold the product to the ground.

5. Pull the starter rope handle slowly with your right

hand until you feel resistance.

WARNING: Do not wind the starter

rope around your hand.

CAUTION: Do not pull the starter

rope to full extension and do not let go of

the starter rope handle. This can cause

damage to the product.

6. Pull the starter rope handle quickly and with force

until the engine starts.

7. Set the choke control to the operation position.

1756 - 001 - 08.06.2022 17

WARNING: Keep body parts away

from the spark plug cap. Risk of burn

injuries. Do not use the product with

a damaged spark plug cap. Risk of

electrical shock.

To start the product (543RS, 553RS)

1. Move the stop switch to the start position.

2. Push the air purge bulb until fuel starts to fill the air

purge bulb.

3. Move the choke control to the choke position.

4. Hold the product to the ground.

5. Pull the starter rope handle slowly with your right

hand until you feel resistance.

WARNING: Do not wind the starter

rope around your hand.

CAUTION: Do not pull the starter

rope to full extension and do not let go of

the starter rope handle. This can cause

damage to the product.

6. Pull the starter rope handle quickly and with force

until the engine starts.

7. Set the choke control to the operation position.

WARNING: Keep body parts away

from the spark plug cap. Risk of burn

injuries. Do not use the product with

a damaged spark plug cap. Risk of

electrical shock.

To start with a throttle handle with a start

throttle lock

1. Push the throttle lockout and the throttle trigger to

set the throttle to the start position. Then push the

start throttle button (A).

2. Release the throttle lockout and the throttle trigger,

followed by the start throttle button. The throttle

function is now activated.

3. To return the engine to idle speed, push the throttle

lockout and throttle trigger again.

A

To stop the engine

1. Push the throttle trigger to the idle position.

2. Move the stop switch to the stop position.

18 1756 - 001 - 08.06.2022

To operate the grass trimmer

CAUTION: Make sure that you slow the

engine to idle speed after each operation. A

long period at full throttle without a load on

the engine can cause damage to the engine.

Note: Clean the cover of the trimmer head when

you attach a new trimmer line to prevent vibrations.

Examine other parts of the trimmer head and clean if

it is necessary.

General work instructions

WARNING: Be careful when you cut a

tree that is in tension. It can spring back to

its normal position before or after the cut and

hit you or the product, and cause injury.

• Clear an open space at one end of the work area,

and start the work from there.

• Move in a regular pattern across the work area.

• Move the product fully to the left and right, to clear a

width of 4–5 m (13-16 ft) on each turn.

• Clear a length of 75 m (250 ft) before you turn and

go back. Move the fuel can along with you as you

continue.

• Move in a direction where you do not go across

ditches and obstacles more than necessary.

• Move in a direction where the wind makes the cut

vegetation fall in the cleared area.

• Move along slopes, not up and down.

Blade thrust

A blade thrust is when the product moves to the side

quickly and with force. A blade thrust occurs when the

grass blade or saw blade hits or catches on an object

that cannot be cut. A blade thrust can eject the product

or operator in all directions. There is a risk of injury to

the operator and bystanders.

The risk increases in areas where it is not easy to see

the material that is cut.

Do not cut with the area of the blade that is shown in

black. The speed and movement of the blade can cause

blade thrust. The risk increases with the thickness of the

branch that is cut.

Forestry clearing with a saw blade

To fell a tree to the left

To fell to the left, push the bottom of the tree to the right.

1. Apply full throttle.

2. Put the saw blade against the tree as given in the

picture.

3. Tilt the saw blade and push it with force diagonally

down to the right. At the same time, push the tree

with the blade guard.

To fell a tree to the right

To fell to the right, push the bottom of the tree to the left.

1. Apply full throttle.

2. Put the saw blade against the tree as given in the

picture.

1756 - 001 - 08.06.2022 19

3. Tilt the saw blade and push it with force diagonally

up and to the right. At the same time, push the tree

with the blade guard.

To fell a tree forward

To fell forward, push the bottom of the tree rearward.

1. Apply full throttle.

2. Put the saw blade against the tree as given in the

picture.

3. Pull the saw blade forward with a fast movement.

To fell large trees

Large trees must be cut from 2 sides.

1. Examine in which direction the tree will fall.

2. Apply full throttle.

3. Do the first cut on the side of the tree to which it will

fall.

4. Cut through the tree from the other side.

CAUTION: If the saw blade becomes

blocked, do not pull the product with a

sudden movement. That can cause damage

to the saw blade, bevel gear, shaft or

handlebar. Release the handles, hold the

shaft with 2 hands and carefully pull the

product.

Note: Use more cutting pressure fo fell small trees.

Use less cutting pressure to fell large trees.

Brush cutting with a saw blade

To fell to the left, push the bottom of the tree to the right.

• Cut down thin trees and brush.

• Move the product from side to side.

• Cut many trees in one movement.

• For groups of thin trees:

a) Cut the outer trees high up.

b) Cut the outer trees to the correct height.

c) Cut from the center. If you cannot get access to

the center, cut the outer trees high up and let

them fall. This decreases the risk that the saw

blade becomes blocked.

To clear grass with a grass blade

1. Keep your feet apart during operation of the product.

Make sure feet are tightly against the ground.

20 1756 - 001 - 08.06.2022

La pagina sta caricando ...

Husqvarna 533RS Manuale utente

Husqvarna 533RS Manuale utente

in altre lingue

Documenti correlati

Altri documenti