LG PQNFG14B0 Manuale del proprietario

LG

CNU

LG

IMPORTANT

• Please read this Installation Manual completely

before installing the product.

• Installation work must be performed in

accordance with the national wiring standards

by authorized personnel only.

• Please retain this Installation Manual for future

reference after reading it thoroughly.

Model: PQNFG14B0

INSTALLATION MANUAL

Visit us at : http://www.lgservice.com

ENGLISH ITALIANO ESPAÑOL FRANÇAIS DEUTSCH

2 CNU

CNU

TABLE OF CONTENTS

■ Cautions for safety .................................................................................................3

■ Part Description ......................................................................................................6

Parts of a CNU..........................................................................................................6

CNU connection........................................................................................................7

■ Wiring Diagram ......................................................................................................8

Multi V SUPER(PLUS) & MPS PRODUCT...............................................................8

Connection................................................................................................................9

■ Network Interface Connection.............................................................................11

Dip Switch Configuration.........................................................................................11

■ CNU setup method................................................................................................12

Connect with the PC...............................................................................................12

Set the PC environment for CNU IP setting............................................................13

CNU Setup Configuration .......................................................................................18

■ CNU Normal operation condition confirmation .................................................19

Hardware operation condition confirmation ............................................................19

LAN communication condition confirmation ...........................................................19

485 Communication condition confirmation............................................................19

Cautions for safety

Installation Manual 3

ENGLISH

You should always request

product installation to our

Service Center or to

installation expert agency.

Use specified parts.

When reinstalling an existing

installed product, request it to

our Service Center or to

installation expert agency.

• Otherwise it may cause

fire hazard, electric shock,

explosion, injury or

damage.

• Or else it may cause fire

hazard, electric shock,

explosion, injury, damage

and trouble failure.

• Otherwise it may cause fire

hazard, electric shock,

explosion, injury or damage.

Don’t keep or use ignitable gas or any other

flammable material in vicinity of the product.

Don’t disassemble, repair and modify the

product at your will.

• Otherwise it may cause fire hazard and

product trouble failure.

• Or else it may cause fire hazard and electric

shock.

Cautions for safety

To prevent injury to the user or other people and property damage, the following instructions must be

followed.

■ Incorrect operation due to ignoring instruction will cause harm or damage. The seriousness is

classified by the following indications.

This symbol indicates the possibility of death or serious injury.

This symbol indicates the possibility of injury or damage to properties only.

■ Meanings of symbols used in this manual are as shown below.

Be sure not to do.

Be sure to follow the instruction.

■ WHEN INSTALLING

SPECIFIED

PA RT S

Benzene

Ether

Thinner

Cautions for safety

4 CNU

Don’t install it where rain falls on. Don’t install it in humid place.

• Otherwise it may cause product failure. • Otherwise it may cause product failure.

Don’t change or extend

electric supply wire at your

will.

Don’t let there exist fire heat

near the product.

Don’t use heat equipment

near the electricity supply

line.

• Or else it may cause fire

hazard and electric shock.

• Otherwise it may cause fire

hazard.

• Or else it may cause fire

hazard and electric shock.

Don’t spill water into interior

of the product.

Don’t put heavy material upon

electricity supply chord.

Don’t put heavy material

upon the product.

• Otherwise it may cause

electric shock and product

failure.

• Or else it may cause fire

hazard and electric shock.

• Or else it may cause

product trouble failure.

Always request to our Service

Center or installation expert agency

in such case as the product has

been submerged under water.

Child or the old and the weak

shall use it under custody of

patron.

Don’t give impact to the

product.

• Or else it may cause fire

hazard and electric shock.

• Otherwise it may cause

safety accident or product

failure.

• If the product is impacted,

it may cause product

trouble failure.

■ WHEN USING

Cautions for safety

Installation Manual 5

ENGLISH

Don’t clean the product with

strong detergent of solvents

but only use soft cloth.

If water has been smeared

on electric charge part, use

it after removing water.

Don’t let metallic products

of necklace, coin, key, watch

etc. touch the battery

terminal.

• Or else it may cause fire

hazard and product

deformation.

• Or else it may cause

product failure.

• Or else it may cause product

failure and injury.

■ WHEN USING

W

a

x

Thinner

Part Description

6 CNU

■ Parts of a CNU

200.0

120.0

7.5

20.0

35.0

55.0

Dimension

CNU CONT BOX

Input voltage : DC9V 2.0A

In/out port : RS232 1ea

RS485 1ea

LAN 1ea

Power supply

DC 9V , 2.0A

Power cord

NOTE : AC input spec.

- 100~250 VAC universal input

- Desktop style or wall plug style

International standard

IEC320 C8 type

LGAP

Part Description

Installation Manual 7

ENGLISH

■ CNU connection

RS-485 Communication Terminal

Connect with PMNFP14A0 (PMNFP14A1) :

BUS_A, B

• Cautions while connecting RS-485

communication line : When connecting the 485

communication line do as the picture below

using the provided core and tie.

Power Connector

DC 9V Adaptor

(supplied)

PQNFG14B0 ----

PMNFP14A0

(PMNFP14A1)

Reset button

• NOTICE

this terminal is for communication stability

so, don’t remove and connect other line

RJ45 Connector :

Connect with HUB OR

Deluxe/PC Central

Controller

L06D: Connection of LAN H/W (LINK LED)

L07D: Connection of LAN H/W LED(DUPLEX)

L08D: 10MEGA BASE Communication LED

(when CNU II is connected with Deluxe central controller)

L09D: 100MEGA BASE Communication LED

(when CNU II is connected with PC central controller)

L10D: COLLISION DETECTOR LED

BUS_A ---- BUS_A

BUS_B ---- BUS_B

Wiring Diagram

8 CNU

ON

L1 2 3 4

KSDO4H

CNU PCB

BUS_A

BUS_B

CNU Connection

DC 9V adaptor connection

PC Central controller

MULTI V OUTDOOR TERMINAL BLOCK

DC 9V

ABEFCD

VCC GND

CN_CENTRAL

Multi-V SUPER

(PLUS) or MPS product

Outdoor main PCB

Please refer to network interface setting method on

the 11 page.

It explains about how to set PI 485(M) dip switch.

■ SUPER(PLUS) & MPS PRODUCT

Wiring Diagram

❈ NOTICE : Use of terminal block in case of Multi V and other models may or may not be needed.

If it is not present, make direct connections.

Wiring Diagram

Installation Manual 9

ENGLISH

■ Connection

Delux

e central contr

oller connection

Cross Cable

Direct Cable

Wiring Diagram

10 CNU

PC central controller connection

Cross Cable

Direct Cable

Use the cross cable if not using the hub.

If willing to use the hub, use the direct

cable to connect with the hub

Network Interface Connection

Installation Manual 11

ENGLISH

■ Dip Switch Configuration

Network Interface Connection

ON

L1 2 3 4

KSDO4H

ON KSDO 4H

ON KSDO4H

Selection air-

conditioner type

Selection

network type

* LGAP : LG Air conditioner Protocol

& MPS MULTI Products Configuration Methods

& MPS

Inverter Product + Without LGAP central controller

Ex) DCC(PQCSW series) or PCC(PQCSS501A0/PQCSS502A0)

1 ON, Al others OFF:

MPS Multi Standard Product + Without LGAP central controller

Ex) DCC(PQCSW series) or PCC(PQCSS501A0/PQCSS502A0)

2 ON, All others OFF:

Multi Standard Product + With LGAP central controller

Ex) PCC(PQCSS513A0)

2 and 4 ON, All others OFF:

Inverter Product + With LGAP central controller

Ex) PCC(PQCSS513A0)

1 and 4 ON, Al others OFF :

& MPS

* Please refer the corresponding Central Controller installation manual if you want to know whether your Central

Controller is compatible with LGAP or not.

12 CNU

CNU setup method

■ Connect with the PC

CNU setup method

❈ NOTICE : The CNU IP is automatically set-up 192.168.1.101 following factory shipment.

Do not set-up the CNU IP if wanting to use the PC Central Control without changing the CNU IP or

Deluxe central controller connection

LAN connection

RS22 connection

Connect Power

DC 9V Adaptor(supplied)

CNU setup method

Installation Manual 13

ENGLISH

■ Set the PC environment for CNU IP setting

1) Check CNU , and connect between PC and CNU by 232 cable.

If your computer doesn't have 232port, Use USB to 232 Port cable.

2) Start up the RS232 Monitoring Program on the PC.

(You can download the RS232 Monitoring Program from LG air conditioner global website.)

3) Follow below procedure.

Install Teraterm

program

Select

serial

Change

port

1.Select language

2.Click Continue

3.Click Continue 4.Installing step of program

5.Finishing step of the installation

Change IP address

And Gateway

Click the

PCB’

s Reset button

Recheck the

Changed DATA

Serial port

Setup to change

baud rate

CNU setup method

14 CNU

Install Teraterm

program

Select

serial

Change

port

Serial port

Setup to change

boud rate

1. Select Serial

2. Reset the Port which is used by 232 cable.

1. Click the starting icon

CNU setup method

Installation Manual 15

ENGLISH

Change

port

Serial port

Setup to change

boud rate

1. Click the Setup button

2. choosing serial port

3. Change boud rate

4. Set 57600

Click the

PCB’s Reset button

CNU setup method

16 CNU

Serial port

Setup to change

boud rate

1. Click the PCB's reset button

1. type the character “C”

Change IP address

And Gateway

Click the

PCB’s Reset button

CNU setup method

Installation Manual 17

ENGLISH

1. type character “2” 2. type IP address 192.168.1.102 , and

Click ENTER key

3. Check the changed IP address

4. If you finish setting, Type “9”

* Follow upper procedure and Change other

setting items properly

Change IP address

And Gateway

Click the

PCB’

s Reset button

Recheck the

Changed DATA

■ Check CNU Setting data

1) MAC : Device Address (Don't change)

2) IP : CNU internet address

3) Gateway : internet Gateway

4) Subnet : Subnet mask (Don't change)

5) Load all info : total information

6) Central Controller Protocol : Select protocol '0' or

'1', refer next page.

7) Daytime Setting

8) Telnet Port : 23 (Don't change)

9) EXIT

CNU setup method

18 CNU

■ CNU Setup Configuration

Press the number which it wants changing

1. MAC address (Don't change)

00.E0.91.0F.XX.XX is an item which is specific value

2. IP : IP set up menu

- Use CNU IP set or change

- Default value in factory is 192.168.1.101

❈ Notice : Incase using private IP, Consult with network manager

3. GATEWAY : network gateway IP set up menu

- Use CNU network gateway IP set or change

- Default value in factory is 192.168.1.1

❈ Notice : Incase using private IP, Consult with network manager

6. Central controller Protocol(1:LGAP,0:OLD) : LGAP selection menu

• select '0' : in using Deluxe central controller or PC central controller without

LGAP(PQCSS501A0/PQCSS502A0)

• select '1' : in using PC central controller with LGAP(PQCSS513A0)

example)

- Central Controller Protocol(LGPA:1, OLD:0) ➔ After input 0, press ENTER

- Central Controller Protocol(LGAP:1, OLD:0) ➔ After input 1, press ENTER

❈ Notice : When the network set goes wrong and does not become the communication

7. Number 1,4,5,7,8 items are not setup Menu.

So, Don't change default value

❈ Notice : After all of settings are finished

You should escape set up mode by typing '9' otherwise, The CNU will not operate normally

CNU Normal operation condition confirmation

Installation Manual 19

ENGLISH

■ Hardware operation condition confirmation

CNU Normal operation condition confirmation

1) Check CNU LED1 is continuously blinking : 485 communication LED

2) Check L06D, L07D LEDs are Lighting : LAN CABLE connection confirmation LED

3) Check L09D,L08D blinking : LAN communication condition confirmation LED

L08D blinking : connected Deluxe central controller(10M BPS)

L09D blinking : connected PC(100M BPS)

❈ Notice : If the LAN cable is are not connected between PC(or DCC) and CNU then the LED6D,7D are not light

■ LAN communication condition confirmation

1) After connecting the LAN CABLE, executing, DOS Command of the PC which is connected

2) PING test : type 'ping' and 'CNU IP' then Enter key

ex) PING 192.168.1.101 (The CNU IP will be different which is real set ,so type real CNU IP)

❈ Notice : The response time will be different to system condition

If ping test is fail(request tine out) then check below condition

- CNU IP is correct?

- PC Network information has same with the CNU IP information

ex) If CNU IP is 192.168.1.101 then the PC network information does to have a same network

information 192.168.1.XXX(except same CNU IP number or 1 )

3) When PING test executes well, LAN communication operates in the normality.

■ 485 Communication condition confirmation

1) Before confirm 485 communication condition, check indoor address setting and 485 G/W operation LED's condition

and power resource condition.

2) Connecting RS232 cable and running RS232 monitoring program

3) In order to appear information in monitoring program window, Setup Com port and Baud rate to 57600.

4) The data will come up and it will be able to confirm a number of indoor

Setup address of indoor appears, 485 communication

operational condition of CNU is normality

ex) number monitoring of connected indoor

❈ Notice : The indoor number searching time could be delayed in in

the condition which searches

When neither information of the indoor information is searched

Check below check points

1) Check Indoor unit address are set correct or not

2) Check the 485 gateway setting (s/w setting, connect

connection..etc.)

3) Check 485 communication line is correct or not BUS_A, BUS_B

Indoor number

Memo

20 CNU

La pagina sta caricando ...

LG PQNFG14B0 Manuale del proprietario

Questo manuale è adatto anche per

LG PQNFG14B0 Manuale del proprietario

in altre lingue

Documenti correlati

Altri documenti