Lindy 4x4 HDMI Matrix Switch Manuale utente

Categoria
Interruttori video
Tipo
Manuale utente
© LINDY Group SECOND EDITION
HDMI 4x4 Matrix
with Video Wall Scaling
User Manual English
Benutzerhandbuch Deutsch
Manuel Utilisateur Français
Manuale Italiano
No. 38131
www.lindy.com
Tested to Comply with
FCC Standards
For Home and Office Use!
User Manual English
Introduction
Thank you for purchasing the LINDY HDMI Video Wall 4x4 Matrix. The HDMI Video Wall 4x4 Matrix allows
the signals from four different sources to be freely selected and arranged on 4 displays (TV, Monitor or
Projector), in one of three output modes; Video Wall, Matrix and dual.
This flexible feature rich product has been designed to be used in a number of different applications, such
as:
Public Advertisement
Digital Presentation
Broadcasting & Control
Surveillance & Control
Conference & Meeting Room
Package Contents
HDMI Video Wall 4x4 Matrix
IR Remote Control
Multi-Country 12V 3A Power Supply (UK/EU/US/AUS)
Driver CD
This manual
Features
Allows 4 HDMI Inputs to be displayed in 3 different modes across 4 HD displays
Video Wall Mode Display an HDMI source across a 2x2 video wall
Matrix Mode Display any HDMI source on any HDMI display
Dual Mode Display 2 sources on a single HDMI display
Seamless switching between HDMI sources
User definable output scaling
Controlled via On-panel controls, IR Remote, RS-232 and Telnet
Bezel correction to aide screen blending
Adjustable picture contrast, brightness, saturation and hue
Memory function to store 4 user determined configurations
Can be used with LINDY HDMI extenders to reach remote displays
Specification
Input ports: 4 x HDMI Female
Input resolution: 480i 1080p*
Output ports: 4 x HDMI Female
Output resolution: 480p 1080p*
Audio support: LPCM 2CH, 6CH, 8CH, AC3, DTS, Dolby Digital Plus, Dolby TrueHD & DTS-HD
Control Ports: RJ45 (Telnet) & Serial 9 Way Male (RS-232)
Video bandwidth: 225MHz/6.75Gbps
Power consumption: 15W
Weight: 2.2Kg
Dimensions: 436x247x44mm (WxDxH)
*Please Note: For additional information regarding the exact resolution/timing combinations which are supported for input and
output please refer to the Timings section at the end of this manual.
User Manual English
Overview & Operation
Front Panel
1. IR Window
Receives IR commands from the supplied IR Remote
2. Power
Switch the Matrix On/Off
3. Menu
Press to launch the OSD menu
Press to make a menu selection in the OSD
Press along with “-“ to set the Output to 720p@60Hz
Press along with “+” to set the Output to 1024x768@60Hz
4. -/+ Buttons
Use these buttons to move up and down in the OSD
5. Channel Input (1 4) / Channel Output (A D) Selection
In Matrix Mode select an Output by pressing one of the buttons marked A D, then select the Input
to be used by pressing one of the buttons marked 1 4. Repeat this for each Output. Each Output
can independently display any of the Inputs according to your selection.
In Dual Mode there are two groups, Dual A (Outputs A & B) and Dual B (Outputs C & D). To set up
Dual A select Output A then select the first input by pressing one of the buttons marked 1 4. Now
select Output B then select the second input by pressing one of the buttons marked 1 4, without
duplicating your initial selection. Your two input selections will now be shown on Output A and Output
B. For Dual B repeat this for Output C and D as required. Press and hold Output A or B for 3 seconds
to select the audio input for Dual A, or Output C or D to select the audio input for Dual B.
In Video Wall Mode select the input to be displayed across the 4 displays (2x2 configuration) by
selecting Input 1 4. Audio will be available through Output A only.
6. Matrix / Dual / Wall Mode
Press this button to switch between the different modes. When Matrix Mode is selected the button will
stay constantly illuminated, for Dual Mode the button will not illuminate and for Video Wall Mode the
button will blink on/off.
7. Lock
Press this button once to lock the keypad and remote control, press and hold the button again for 3
seconds to release the lock.
8. Save
Once you have configured the Matrix (Mode selection, Input/Output combinations etc.) press the Save
button, the Input 1 4 buttons will then illuminate. Now press one of the Input buttons to save your
configuration. Pressing Input 1 would save the configuration to slot 1, this can then be recalled using
the Recall button (see below) or by pressing Fav.1 on the IR Remote.
9. Recall
Press the Recall button, the Input 1 4 buttons will then illuminate. Now select which saved
configuration you want to recall by pressing Input button 1/2/3/4.
OUTPUT
A
B
C
D
INPUT
1
2
3
4
SAVE
RECALL
LOCK
MATRIX/
DUAL/WALL
MENU
-
+
XGA
720P
1
2
3
4
5
8
9
7
6
User Manual English
Rear Panel
1. HDMI In 1 4
Connect your HDMI sources devices such as PC, Blu-ray etc to these ports
2. HDMI Out A D
Connect your HDMI displays to these ports
3. Control
Connect to an Ethernet network for Telnet control
4. USB Service Only
Reserved for Factory use only
5. RS-232
For connection to a PC/Notebook or Remote Control Processing unit
6. DC 12V
Connect the supplied 12V power supply here
Remote Control
1. Power
Switch the Matrix On/Off
2. Info
Press to display the Matrix’s firmware version
3. Output A D & Input 1 4
Provide the same function as the front panel buttons
4. Matrix/Dual/Wall Mode Selection
Provide the same function as the front panel buttons
5. Lock
Provides the same function as the front panel button
6. Mute
Press to Mute audio playback from the HDMI output port
7. Navigation/Selection Buttons
Press to navigate the OSD and make selections
8. Menu
Press to enter the OSD menu
9. Exit
Press to exit the OSD menu
10. Output Resolution
Press to quickly change the Output resolution
11. Dual Mode Audio
Switch between Left/Right input source audio, for Dual A or Dual B
12. Save
Provides the same function as the front panel button
13. FAV. 1 4
Recalls the settings saved to the corresponding save location
1
2
3
4
5
6
HDMI IN
1
2
3
4
A
B
C
D
HDMI OUT
CONTROL
RS232
DC 12V
USB
SERVICE
ONLY
INFO
POWER
Out A
In 1
Matrix
Out B
In 2
Dual
Out C
In 3
TV Wall
Out D
In 4
Lock
Mute
OK
Exit
Menu
1024x768
Save
FAV.1
720p
1080p
FAV.2
AL
AR
FAV.3
FAV.4
BR
BL
1
2
3
4
5
6
7
8
9
10
11
13
12
User Manual English
By removing the battery cover of the IR Remote you can access a set of dip switches which allow you to
change the default IR address, as may be required if multiple Matrixes’ are used in close proximity or if
there is interference with another IR device. Before changing the dip switch setting from its default of 0,
please change the IR setting on the Matrix first. Enter the OSD and then select Others, now select IR
Address and select the desired address 0 3.
Connection Diagram
Set-Top Box
Blu-Ray Player
HDMI
Cable
HDMI
Cable
HDMI
Cable
HDMI
Cable
HDMI
Cable
HDMI
Cable
RJ45
Cable
9 Way Serial
Cable
PC
TV/Display
TV/Display
TV/Display
TV/Display
Notebook
Notebook
User Manual English
Video Output Modes
Video Wall
Displays a single user definable HDMI source across a 2x2
video wall.
Video Matrix
Display any HDMI source on any HDMI display.
Dual Output
Display 2 HDMI sources on a single HDMI Output. Outputs
are grouped as follows Dual A (Outputs A & B) and Dual B
(Outputs C & D).
RS-232, Telnet & OSD Control
RS-232 & Telnet Control
The Matrix may also be controlled via PC software which can be downloaded from www.lindy.com, or
using Hyper Terminal. The PC software provides a graphical interface for control as shown below:
Simple Control Panel
Full Function Control Panel
User Manual English
RS-232 Protocols
Baud Rate: 115200bps Data Bit: 8 bits
Parity: None
Flow Control: None
Stop Bit: 1
Telnet Setting
Use TCP/IP (Port 23) for Telnet communication.
RS-232 & Telnet Commands
Command
Active
4x4 Matrix Return
ASP000
Aspect Ratio is Full
ASP000
ASP001
Aspect ratio is 4:3 TV
ASP001
ASP002
Aspect Ratio is 16:9 TV
ASP002
ASP003
Aspect Ratio is 16:10 TV
ASP003
ASP004
Aspect Ratio is to Keep Ratio
ASP004
ASP999
Check Aspect Ratio Status
ASP999
AUA001
Dual A Audio channel in Left side
AUA001
AUA002
Dual A Audio channel in Right side
AUA002
AUA999
Check Dual A audio channel status
AUA???
AUB001
Dual B Audio channel in Left side
AUB001
AUB002
Dual B Audio channel in Right side
AUB002
AUB999
Check Dual B audio channel status
AUB???
AUD000
Audio output Off
AUD000
AUD001
Audio output On
AUD001
AUD999
Check audio on/off status
AUD???
AUE000
Audio EDID is LPCM 2CH
AUE000
AUE001
Audio EDID is LPCM 6CH
AUE001
AUE002
Audio EDID is LPCM 8CH
AUE002
AUE003
Audio EDID is BITSTREAM
AUE003
AUE004
Audio EDID is HD
AUE004
AUE999
Check audio EDID setting
AUE???
AUQ001
Quad Audio from Quad 1
AUQ001
AUQ002
Quad Audio from Quad 2
AUQ002
AUQ003
Quad Audio from Quad 3
AUQ003
AUQ004
Quad Audio from Quad 4
AUQ004
AUQ999
Check Quad Audio Setting
AUQ???
BEZ000
Bezel Correction OFF
BEZ000
BEZ001
Bezel Correction ON
BEZ001
BEZ999
Check bezel correction on/off status
BEZ???
BEH???
Horizontal (H) Bezel correction???=000 - Maximum
BEH???
BEH998
Check the current Horizontal(H) Bezel correction Maximum value
BEH???
BEH999
Check the current Horizontal(H) Bezel correction setting value
BEH???
BEV???
Vertical (V) Bezel correction???=000- Maximum
BEV???
BEV998
Check the current Vertical(V) Bezel correction Maximum value
BEV???
User Manual English
Command
Active
4x4 Matrix Return
BEV999
Check the current Vertical(V) Bezel correction setting value
BEV???
BRI???
Setting Brightness
No response
???=000-100 for matrix mode
???=(000-100)+200*(OUT No.-1) for dual/tv wall mode
For example: OUT B set the Brightness value to 57 =(57)+200*(2-1) = 257
BRI99?
Check current Brightness value
BRI???
99?=999 for matrix mode
99?=991-994=OUT1-4 for dual/tv wall mode
CAL???
RECALL FAV. ???=001-004=FAV.1-4
CAL???
CON???
Setting Contrast
No Response
CON999
Command setting same as Brightness(BRI)
CON???
DUL001
Set Dual mode to PoP
DUL001
DUL002
Set Dual mode to PiP
DUL002
DUL003
Check Dual mode status
DUL999
EGW999
RS232 only, check current Ethernet
Gateway Address
aaa.bbb.ccc.ddd
EIP999
RS232 only, check current Ethernet IP
Address
aaa.bbb.ccc.ddd
EMK999
RS232 only, check current Ethernet
Subnet Mask Address
aaa.bbb.ccc.ddd
HLP999
Show Command List
Command List
HPI0xy
HDCP Input setting
x=1~4=IN 1~4, y=o=On, y=1=Off
HPI0xy
HPI99?
Check HDCP INPUT setting ?=1~4
=IN1~4
HPI0xy
HPO0xy
HDCP Output setting
x=1~4=OUT A~D, y=o=Follow Input,
y=1=Follow Output
HPI0xy
HPO99?
Check HDCPOUTPUT setting ?=1~4
=OUT A~D
HPO0xy
HUE???
Setting HUE
No Response
HUE999
Command setting same as Brightness
(BRI)
HUE???
INP???
INPUT selection???=001~004=IN 1~4
INP???
Execute OUT???
INP999
Check current INPUT
INP???
LAB000
Set Input Label Off
LAB000
LAB001
Set Input Label On
LAB001
LAB999
Check current Input Label On/Off
LAB???
LAIxyyyyyyy
Set Input Lable Name
x=1~4=In 1~4, yyyyyyyyyyyy max. 12
Character
LAIxyy…
LAI99?
Check input Lable Character ?=1~4
=IN 1~4
LAIxyy…
LCK000
Un-lock
LCK000
LCK001
Lock
LCK001
LCK999
Check current Lock/Un-lock status
LCK???
MNE001
OSD Menu EXIT
No Response
MND001
OSD Menu DOWN
No Response
MNL001
OSD Menu LEFT (-)
No Response
MNO001
OSD Menu OK
No Response
MNR001
OSD Menu RIGHT (+)
No Response
MNU001
OSD Menu UP
No Response
MNX001
OSD Menu
No Response
User Manual English
Command
Active
4x4 Matrix Return
MOD001
Matrix Mode
MOD001
MOD002
Dual PoP Mode
MOD002
MOD003
TV Wall Mode
MOD003
MOD004
Dual PiP Mode
MOD004
MOD005
Quad Mode
MOD005
MOD999
Check current output mode status
MOD???
OUT???
OUTPUT selection???=001~004=OUT
A~D
OUT???
OUT999
Check current OUTPUT
OUT???
PPO0xy
Dual PiP/Sub Position x=1~2=PiP A~B
y=0=Upper left, 1=Upper right, 2=Lower
right, 3= Lower left
PPO0xy
PPO99?
Check PiP/Sub Postion status
?=1~2=PiP A~B
PPO0xy
PSW001
Dual PiP A(Main) image swap with
Sub
PSW001
PSW002
Dual PiP B(Sub) image swap with Main
PSW002
PSZ0xy
Dual PiP/Sub Size x=1~2=PiP A~B
y=0=Large, 1=Medium, 2=Small, 3= Off
PSZ0xy
PSZ99?
Check PiP/Sub Size status
?=1~2=PiP A~B
PSZ0xy
PWR000
Power Off (Standby)
PWR000
PWR001
Power On
PWR001
PWR999
Check Current Power Status
PWR???
RES???
Output resolution???=001~ ...corresponding
osd menu list
RES???
RES999
Check current output resolution
RES???
RST001
Factory Reset
RST001
RST002
Picture Reset
RST002
SAT???
Setting Saturation
No Response
SAT999
Command setting same as Brightness
(BRI)
SAT???
SAV???
SAVE FAV. ???=001~004=FAV.1~4
SAV???
VER999
Check Firmware Version
VER???
Example:
VER110=V1.1
VR2999
Check Customers Firmware Version
VR2???
On-Screen-Display (OSD) Menu
Main Menu
Sub Menu
Adjustments
Default
PICTURE (1)
ALL
CONTRAST
0 - 100
50
BRIGHTNESS
0 - 100
50
SATURATION
0 - 100
50
HUE
0 - 100
50
DUAL
DUAL AL
DUAL AR
DUAL BL
DUAL BR
TV WALL
OUT A
OUT B
OUT C
User Manual English
Main Menu
Sub Menu
Adjustments
Default
OUT D
D/T
RESET
ALL
RESET ALL
EXIT
OUTPUT RESOLUTION
480p
720p60
576p
720p50
720p60
1080i50 (2)
1080i60 (2)
1080p24
1080p50
1080p60
1024x768
1280x800
1280x1024
1366x768
1440x900
1600x900
1600x1200
1680x1050
1920x1200
EXIT
AUDIO EDID (3)
LPCM 2CH
LPCM 2CH
LPCM 6CH
LPCM 8CH
BIT-STREAM
HD
EXIT
OSD SETTINGS
POSITION
LEFT T
LEFT T
RIGHT T
LEFT B
RIGHT B
H OFFSET
0 - 20
10
V OFFSET
0 - 20
10
TRANSPARENCY
0 - 9
4
OSD SETTINGS
(CONTINUED)
MENU TIMEOUT
5 - 50, OFF (4)
8
INFO.TIMEOUT
5 - 50, OFF
8
INFO.DISPLAY
ON
ON
OFF
BRIEF INFO
ON
OFF
OFF
EXIT
HDCP
INPUT (5)
ACCEPT
ACCEPT
NOT ACCEPT
OUTPUT (6)
FOLLOW INPUT
FOLLOW INPUT
ALWAYS ON
EXIT
BEZEL CORRECTION (7)
CORRECTION
ON
OFF
OFF
User Manual English
Main Menu
Sub Menu
Adjustments
Default
H CORRECTION
0 - by output resolution
0
V CORRECTION
0 - by output resolution
0
EXIT
RECALL / SAVE (8)
RECALL
CANCEL
~ 4
CANCEL
FAV. 1
FAV. 2
FAV. 3
FAV. 4
SAVE
CANCEL
CANCEL
FAV. 1
FAV. 2
FAV. 3
FAV. 4
EXIT
ETHERNET
IP MODE
DHCP
DHCP
STATIC
STATIC SET
IP
IP
MASK
GATE
BYTE1
192
BYTE2
168
BYTE3
5
BYTE4
155
RE-LINK (9)
TIMEOUT (Min.) (10)
5 - 60
10
OFF
EXIT
OTHERS
IR ADDRESS (11)
0 - 3
0
EXIT
FACTORY DEFAULT
YES
NO
NO
EXIT
INFORMATION
(*12)
IN/OUT RESOLUTION
SOURCE HDCP/AUDIO
OUT MODE
FIRMWARE VER
EXIT
EXIT
Notes:
1 Picture
In Matrix mode, all four pictures are adjusted simultaneously.
In Dual/TV Wall mode, each picture can be adjusted individually and supports the last memory feature.
2 Output
In Matrix mode if the Output is set to 1080i@50Hz or 1080i@60Hz Input 4 will be disabled.
3 AUDIO EDID
Embedded input audio EDID contents:
LPCM 2CH = LPCM 2CH
LPCM 6CH = LPCM 2CH/ 6CH
User Manual English
LPCM 8CH = LPCM 2CH/ 6CH/ 8CH
BITSTREAM = LPCM 2CH, AC3, DTS
HD = LPCM 2CH/ 6CH/ 8CH, AC3, DTS, Dolby Digital Plus, DTS-HD
4 TIMEOUT
Setting to OFF means that MENU and INFO will continuously be shown on the screen.
5 HDCP INPUT
ACCEPT: Supports source using HDCP, this is normal source setting.
NOT ACCEPT: Will not accept a source using HDCP.
6 HDCP OUTPUT:
FOLLOW INPUT: If the Input source uses HDCP the Output signal will support HDCP. If the Input
source does not use HDCP the Output signal will not support HDCP. When
in Dual mode, if either of the
Input sources (Left or Right) uses HDCP, the
output will support HDCP.
ALWAYS ON: When using this setting all connected TV/Monitors must support HDCP. Using displays
which do not support HDCP will result in flashing image/no image when HDCP content is used.
7 BEZEL CORRECTION
This setting is only supported in TV Wall mode, after adjustment the system will save the setting until the
next time it is changed.
8 SAVE/RECALL
Used to SAVE/RECALL input/output settings and all other system settings such as bezel correction or
picture adjustment.
9 Ethernet RE-LINK:
After the setting up the system use this setting to re-link/refresh the
network connection.
10 Ethernet TIMEOUT:
Select OFF to end the time out functions of either the Ethernet or Telnet connection.
Timings
Supported Input Timings
Support Timing
480i@59
480p@60
576i@50
576p@50
720p@25,30,50,60,
1080i@50,60
1080p@24,25,30,50,60
640x480@60,72,75,85
720x400@70
800x600@56,60,72,75,85
1024x768@60,70,75,85
1152x864@70,75
1280x720@60cvt
1280x768@60RB,60,75
1280x800@60RB,60,75
1280x1024@60,60cvt,75
1360x768@60
1366x768@60RB,60
1400x1050@60RB,60
1440x900@60RB,60,75
1600x900@60RB
1600x1200@60
1680x1050@60RB,60
1920x1200@60RB
User Manual English
Supported Output Timings
Support Timing
480p60
576p50
720p50
720p60
1080i50 (Matrix Mode Only)
1080i60 (Matrix Mode Only)
1080p24
1080p50
1080p60
1024x768@60
1280x800@60
1280x1024@60
1366x768@60
1440x900@60
1600x900@60RB
1600x1200@60
1680x1050@60
1920x1200@60RB
Benutzerhandbuch Deutsch
Einführung
Dieser HDMI 2x2 Videowand Matrix Umschalter und Scaler erlaubt das freie Umschalten zwischen 4 HDMI
Eingangssignalen und 4 HDMI Ausgangssignalen. Er kann sowohl als Matrix-Umschalter als auch als
Scaler sowie im gemischten Betrieb eingesetzt werden.
Dieser vielseitige und flexible Umschalter ist ideal geeignet für viele Einsatzzwecke wie z.B.:
Öffentliche Videowände (Digital Signage)
Digitale Präsentationen
Video Broadcasting & Monitoring
Video Überwachung
Konferenzraumtechnologie
Lieferumfang
HDMI Video Wall 2x2 Matrix
IR Fernbedienung
Multi-Country Netzteil 100…240VAC / 12V 3A mit Steckeradaptern für Euro, UK, US, AUS
Treiber-CD
Dies Handbuch
Eigenschaften
Schaltet 4 HDMI Eingänge in 3 Modi auf 4 HDMI Ausgänge um
Videowand Modus Skaliert einen HDMI Eingang auf eine 2x2 Videowand
Matrix Modus Schaltet unabhängig zwischen allen 4 Ein- und Ausgängen um
Dual Modus Zeigt 2 HDMI Eingänge auf einem Display an
Unabhängiges Umschalten zwischen den 4 HDMI Eingängen
Skalierung des Ausganges einstellbar durch Anwender
Steuerbar über Gerätetasten, Fernbedienung, RS232 und Telnet
Rahmenkorrekturoption zur Korrektur der Verzerrung durch die Displayrahmen
Einstellbarer Bildkontrast, Helligkeit, Farbsättigung und Farbton
Speichermöglichkeit für 4 Anwendereinstellungen
Unterstützt LINDY HDMI Extender zum Anschluss der Displays / Signalquellen
Spezifikationen
Eingänge: 4 x HDMI Buchse
Unterstützte Eingangsauflösungen: 480i 1080p*
Ausgänge: 4 x HDMI Buchse
Unterstützte Ausgangsauflösungen: 480p 1080p*
Audiounterstützung: LPCM 2CH, 6CH, 8CH, AC3, DTS, Dolby Digital Plus, Dolby TrueHD & DTS-HD
Steuerungseingänge: RJ45 (Telnet), Serielle Sub-D 9 Pol Steckerbuchse (RS232)
Videobandbreite: 225MHz/6.75Gbps
Leistungsaufnahme: ca. 15W
Gewicht: ca. 2.2Kg
Abmessungen: ca. 436x247x44mm (WxDxH)
*Hinweis: Bitte beachten Sie für exakte Angaben die Auflösungs-/Timing-Tabelle am Ende des Handbuches.
Benutzerhandbuch Deutsch
Installation und Betrieb
Vorderseite und Bedienelemente
1. IR Sensorfeld
Der Sensor für die IR Fernbedienung liegt hinter diesem Fenster
2. POWER
EIN/AUS Schalter
3. MENU
Drücken ruft das OSD Menü (Bildschirmmenü) auf
Drücken um im OSD Menü eine Auswahl zu treffen
Gleichzeitiges Drücken mit der -Taste stellt den HDMI Ausgang auf 720p@60Hz ein
Gleichzeitiges Drücken mit der “+“ Taste stellt den HDMI Ausgang auf 1024x768@60Hz ein
4. - / + Tasten
Drücken dieser Tasten um im OSD auf und ab zu navigieren
5. Kanalwahltasten INPUT (1 4) / OUTPUT (A D)
Matrix Modus: Drücken Sie zuerst einen Ausgang Taste A D, und dann den zugehörigen Eingang
Taste 1 4. Widerholen Sie diese Schritte für alle Ausgänge.
Dual Modus: Die Ausgänge A und B sind zur Gruppe Dual A und die Ausgänge C und D zur Gruppe
Dual B zusammen gefasst. Um Dual A zu programmieren drücken Sie Output A und dann einen der
Eingänge 1 - 4.Drücken Sie nun Output B und einen anderen der Eingänge 1 4. Ihre beiden
gewählten Eingänge werden nun auf den Ausgängen A und B gezeigt. Wiederholen Sie diesen Setup
für Dual B mit den Ausgängen C und D. Drücken und halten Sie Output A oder B für etwa 3 Sekunden
und wählen Sie das zugehörige Audiosignal für Dual A oder Dual B aus.
Videowand Modus: Wählen Sie einfach nur den Eingangsport 1 4 aus um dessen Bildsignal auf
die 2x2 Monitorwand zu verteilen. Das Audiosignal wird ausschließlich über OUTPUT A ausgegeben.
6. MATRIX / DUAL / WALL Modus
Drücken Sie diese Taste um zwischen den Modi umzuschalten. Wenn der Matrix Modus gewählt ist
leuchtet die Taste permanent. Im Dual Mode Betrieb ist die Taste dunkel, im Videowand Mode blinkt
die Taste.
7. LOCK
Drücken dieser Taste sperrt die Eingabe aller Tasten sowie die Fernbedienung. Drücken und Halten
für 3 Sekunden entsperrt.
8. SAVE
Wenn Sie eine Einstellung abspeichern wollen drücken Sie die SAVE Taste. Die INPUT Tasten 1 4
leuchten auf, wählen Sie die unter der Sie das Setup speichern wollen.
9. RECALL
Wenn Sie eine gespeicherte Einstellung aufrufen wollen drücken Sie die RECALL Taste. Die INPUT
Tasten 1 4 leuchten auf, drücken Sie die entsprechende Taste.
OUTPUT
A
B
C
D
INPUT
1
2
3
4
SAVE
RECALL
LOCK
MATRIX/
DUAL/WALL
MENU
-
+
XGA
720P
1
2
3
4
5
8
9
7
6
Benutzerhandbuch Deutsch
Rückseite und Anschlüsse
1. HDMI In 1 4
Zum Anschluss der HDMI Signalquellen wie PC, Blu-ray etc
2. HDMI Out A D
Anschlüsse für Ihre HDMI Displays / Projektoren
3. Control
RJ45 Netzwerkanschluss für Telnet Bedienung
4. USB Service Only
Reserviert für Updates etc.
5. RS232
Zur Fernsteuerung über RS232 z.B. von PC/Notebook oder Remote Control Device
6. DC 12V
Netzteilanschluss
IR Fernbedienung
1. Power
Zum EIN/AUS-schalten des Matrix Switch
2. Info
Zeigt die Firmware Version des Switch an
3. Output A D & Input 1 4
Identische Funktion wie Tasten an der Vorderseite
4. MATRIX / DUAL / WALL Modus
Identische Funktion wie Tasten an der Vorderseite
5. Lock
Identische Funktion wie Tasten an der Vorderseite
6. Mute
Schaltet den Ton / die Lautstärke AUS
7. Navigations-/Auswahltasten
Zum Navigieren und Auswählen im OSD
8. Menu
Schaltet das OSD ein
9. Exit
Schaltet das OSD aus
10. Auflösung für Ausgangssignal
Zum schnellen Wechsel der Ausgangsauflösungen
11. Dual Mode Audio
Schaltet zwischen dem Audiosignal für rechte/linke Bildschirmhälfte
um, nur für Dual A oder Dual B
12. Save
Identische Funktion wie Tasten an der Vorderseite
13. FAV. 1 4
Identische Funktion wie RECALL Taste an der Vorderseite
1
2
3
4
5
6
HDMI IN
1
2
3
4
A
B
C
D
HDMI OUT
CONTROL
RS232
DC 12V
USB
SERVICE
ONLY
INFO
POWER
Out A
In 1
Matrix
Out B
In 2
Dual
Out C
In 3
TV Wall
Out D
In 4
Lock
Mute
OK
Exit
Menu
1024x768
Save
FAV.1
720p
1080p
FAV.2
AL
AR
FAV.3
FAV.4
BR
BL
1
2
3
4
7
8
9
10
11
13
12
5
6
Benutzerhandbuch Deutsch
Nach Abnehmen des Batteriefaches an der Fernbedienung finden Sie 4 DIP Switches um die Default IR
Adresse der Fernbedienung umzustellen, z.B. falls Sie mehrere dieser Matrix Switches in einer größeren
Umgebung gemeinsam betreiben wollen oder falls Interferenzen mit anderen Fernbedienungen anderer
Geräte auftreten. Bevor Sie die DIP Switches umstellen ändern Sie die Einstellung im Switch selber: öffnen
Sie das OSD und wählen Sie OTHERS > IR ADDRESS und einen Wert 1 - 3. Stellen Sie anschließend
den DIP Switch in der Fernbedienung um.
Beispielaufbau
Set-Top Box
Blu-Ray Player
HDMI
Kabel
HDMI
Kabel
HDMI
Kabel
HDMI
Kabel
HDMI
Kabel
HDMI
Kabel
RJ45
Kabel
9 Pol serielles
Kabel
PC
TV/Display
TV/Display
TV/Display
TV/Display
Notebook
Notebook
Benutzerhandbuch Deutsch
Video Output Modi
Videowand / Video Wall
Stellt ein Eingangssignal auf einer 2x2 4 Monitorwand dar.
Video Matrix
Schaltet unabhängig 4 Eingänge auf 4 Ausgänge.
Dual Output
Fügt 2 HDMI Eingänge auf einem HDMI Ausgang
zusammen. Die Ausgänge sind gruppiert in Dual A
(Ausgang A & B) und Dual B (Ausgang C & D).
RS-232, Telnet & OSD Fernsteuerung
Der Matrix Switch kann komfortabel via PC Software oder Hyperterminal ferngesteuert werden. Hier
finden Sie die erweiterten Einstellungsmöglichkeiten wie Rahmenkorrektur und Bildeinstellungen
komfortabel bedienbar. Laden Sie die Software von unserer Webseite herunter. Sie stellt folgendes
grafisches Interface zur Verfügung:
Einfaches Control Panel
Erweiterrtes (Advanced) Control Panel
Benutzerhandbuch Deutsch
RS-232 Protokolle
Baud Rate: 115200bps
Data Bit: 8 bits
Parity: None
Flow Control: None
Stop Bit: 1
Telnet Einstellung
Verwenden Sie TCP/IP (Port 23) für Telnet Kommunikation.
RS-232 & Telnet Kommandos
Command
Active
4x4 Matrix Return
ASP000
Aspect Ratio is Full
ASP000
ASP001
Aspect ratio is 4:3 TV
ASP001
ASP002
Aspect Ratio is 16:9 TV
ASP002
ASP003
Aspect Ratio is 16:10 TV
ASP003
ASP004
Aspect Ratio is to Keep Ratio
ASP004
ASP999
Check Aspect Ratio Status
ASP999
AUA001
Dual A Audio channel in Left side
AUA001
AUA002
Dual A Audio channel in Right side
AUA002
AUA999
Check Dual A audio channel status
AUA???
AUB001
Dual B Audio channel in Left side
AUB001
AUB002
Dual B Audio channel in Right side
AUB002
AUB999
Check Dual B audio channel status
AUB???
AUD000
Audio output Off
AUD000
AUD001
Audio output On
AUD001
AUD999
Check audio on/off status
AUD???
AUE000
Audio EDID is LPCM 2CH
AUE000
AUE001
Audio EDID is LPCM 6CH
AUE001
AUE002
Audio EDID is LPCM 8CH
AUE002
AUE003
Audio EDID is BITSTREAM
AUE003
AUE004
Audio EDID is HD
AUE004
AUE999
Check audio EDID setting
AUE???
AUQ001
Quad Audio from Quad 1
AUQ001
AUQ002
Quad Audio from Quad 2
AUQ002
AUQ003
Quad Audio from Quad 3
AUQ003
AUQ004
Quad Audio from Quad 4
AUQ004
AUQ999
Check Quad Audio Setting
AUQ???
BEZ000
Bezel Correction OFF
BEZ000
BEZ001
Bezel Correction ON
BEZ001
BEZ999
Check bezel correction on/off status
BEZ???
BEH???
Horizontal (H) Bezel correction???=000 - Maximum
BEH???
BEH998
Check the current Horizontal(H) Bezel correction Maximum value
BEH???
BEH999
Check the current Horizontal(H) Bezel correction setting value
BEH???
BEV???
Vertical (V) Bezel correction???=000- Maximum
BEV???
BEV998
Check the current Vertical(V) Bezel correction Maximum value
BEV???
Benutzerhandbuch Deutsch
Command
Active
4x4 Matrix Return
BEV999
Check the current Vertical(V) Bezel correction setting value
BEV???
BRI???
Setting Brightness
No response
???=000-100 for matrix mode
???=(000-100)+200*(OUT No.-1) for dual/tv wall mode
For example: OUT B set the Brightness value to 57 =(57)+200*(2-1) = 257
BRI99?
Check current Brightness value
BRI???
99?=999 for matrix mode
99?=991-994=OUT1-4 for dual/tv wall mode
CAL???
RECALL FAV. ???=001-004=FAV.1-4
CAL???
CON???
Setting Contrast
No Response
CON999
Command setting same as Brightness(BRI)
CON???
DUL001
Set Dual mode to PoP
DUL001
DUL002
Set Dual mode to PiP
DUL002
DUL003
Check Dual mode status
DUL999
EGW999
RS232 only, check current Ethernet
Gateway Address
aaa.bbb.ccc.ddd
EIP999
RS232 only, check current Ethernet IP
Address
aaa.bbb.ccc.ddd
EMK999
RS232 only, check current Ethernet
Subnet Mask Address
aaa.bbb.ccc.ddd
HLP999
Show Command List
Command List
HPI0xy
HDCP Input setting
x=1~4=IN 1~4, y=o=On, y=1=Off
HPI0xy
HPI99?
Check HDCP INPUT setting ?=1~4
=IN1~4
HPI0xy
HPO0xy
HDCP Output setting
x=1~4=OUT A~D, y=o=Follow Input,
y=1=Follow Output
HPI0xy
HPO99?
Check HDCPOUTPUT setting ?=1~4
=OUT A~D
HPO0xy
HUE???
Setting HUE
No Response
HUE999
Command setting same as Brightness
(BRI)
HUE???
INP???
INPUT selection???=001~004=IN 1~4
INP???
Execute OUT???
INP999
Check current INPUT
INP???
LAB000
Set Input Label Off
LAB000
LAB001
Set Input Label On
LAB001
LAB999
Check current Input Label On/Off
LAB???
LAIxyyyyyyy
Set Input Lable Name
x=1~4=In 1~4, yyyyyyyyyyyy max. 12
Character
LAIxyy…
LAI99?
Check input Lable Character ?=1~4
=IN 1~4
LAIxyy…
LCK000
Un-lock
LCK000
LCK001
Lock
LCK001
LCK999
Check current Lock/Un-lock status
LCK???
MNE001
OSD Menu EXIT
No Response
MND001
OSD Menu DOWN
No Response
MNL001
OSD Menu LEFT (-)
No Response
MNO001
OSD Menu OK
No Response
MNR001
OSD Menu RIGHT (+)
No Response
MNU001
OSD Menu UP
No Response
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52

Lindy 4x4 HDMI Matrix Switch Manuale utente

Categoria
Interruttori video
Tipo
Manuale utente