LG OCF100 Manuale utente

www.lg.com

OWNER’S MANUAL

CANVAS SPEAKER

Please read this manual carefully before operating your set and retain it

for future reference.

P/NO : MFL67980402 (1310-REV00)

Printed in Korea

OCF100

2

ENG

ENGLISH

TABLE OF CONTENTS

3 SAFETY INSTRUCTIONS

5 BEFORE INSTALLATION

6 UNPACKING

7 INSTALLATION

7 Attaching the Guide Spacer on the TV

8 Attaching Set Protection Cushion

8 Checking the Spots for Fixing Screws on the Wall Using VESA Guide Sheet

9 Fixing Anchors and Screws

9 Installing the Wall Mounting Supporter

10 Assembling the Wall Mounting Supporter and the Canvas Speaker

11 Adjusting the Level of the Product

12 Organizing the Power Cord

13 Fixing the Safety Clip (Bottom)

13 Connecting the Optical Cable

14 Combined Appearance of the Canvas Speaker and TV

14 PRODUCT SPECIFICATIONS

WARNING

y

If you ignore the warning message, you may be seriously injured or there is a possibility of accident

or death.

CAUTION

y

If you ignore the caution message, you may be slightly injured or the product may be damaged.

3

ENGENGLISH

SAFETY INSTRUCTIONS

- Make sure the professional installer read this manual before installation.

- After the installation, the professional installer should pass this user manual to the customer and ask the

customer to read the manual carefully and keep it in a safe place.

After reading the user manual, keep the manual in a readily accessible location so the users can refer to

it in the future as required.

WARNING

The product should be installed by a

professional installer designated by the

retailer.

Having the product installed by a non-specialized

installer is very dangerous and can cause a personal

injury.

Do not install the product where the weight

cannot be supported.

If the location where the product is installed is not stable

and sturdy enough, it may fall causing personal injuries.

Contact a professional installer designated by

the retailer to move or replace the product, if

needed.

Installation requires special techniques and moving or

installing the product on your own can cause serious

safety issues.

After installing the product, do not hang on it

or apply severe impact to the product.

The product may fall causing personal injuries.

When installing the wall mount-type product,

never hang the power cable or signal cable on

the rear side of the TV.

The cord can be damaged, resulting in a re, an electric

shock or damage to the product.

4

ENG

ENGLISH

SAFETY INSTRUCTIONS

CAUTION

Install the product according to the directions

in this user manual.

Failure to follow the directions in the user manual

may cause a serious personal injury or damage to the

product due to the improper installation.

At least two people must work together when

installing the product or adjusting the height

of the product after the installation.

Working alone may cause the product to fall, resulting in

personal injury or damage to the product.

Check the type of wall material before the

installation and use the provided anchors and

screws if the conditions comply.

If you do not use the designated anchors or screws, they

may not be able to withstand the weight of the product

and cause a safety issue.

When drilling holes in the wall, always use a

drill bit and drill in designated diameter.

If you make a hole to install the product without following

the instructions, the product may not be installed stably,

resulting in a safety issue.

Do not wipe the product with a wet towel

and make sure you do not use any heater

or humidier under the location where the

product is installed.

If water ows into the product or moisture and heat are

applied to the product, it may cause a re, an electric

shock or product malfunction.

Do not install the product in any place other

than the vertical wall, for example, near a

sprinkler or sensor, in a place where may be

affected by vibration or shock, or near any

high voltage power cable or power source.

Unplug the power cord from the power outlet

before installing the product.

If you install the product with the power cord plugged, it

may cause an electric shock or a re.

Do not install the product with bare hands.

Always wear proper work gloves.

Otherwise, this may result in personal injuries.

When you do use other cables than the

provided one to connect the product, the

wall or the connector of the product may be

damaged due to the friction with the wall.

Make sure to use the cable gender provided

with the product.

5

ENGENGLISH

BEFORE INSTALLATION

y

Use this product only for installing the TV on the wall.

y

Be cautious when installing/using the wall mounting product in order to prevent the damage to the

product and avoid safety accidents.

y

If you have not fully read and understood the installation manual, do not install the product and contact

an authorised service centre.

If you have not fully understood after the inquiry, have a specialized installer install the product for you.

y

Even if you are not a specialized installer but have experience in mechanical or construction eld, it is

advantageous for you to fully understand this manual and install the product.

y

This product is designed to be mounted to walls with standard space between the studs. LG Electronics

is not responsible for any issues occurred by installing the product on the walls where the standard

space is not applicable.

y

Install the wall mounting screws to the wall so that they can be installed at the centre of the both ends of

the studs.

It is recommended to use the stud nder, a separate device.

y

When installing the bracket on a concrete wall or on any other walls capable of holding the strength

specied in the manual, you may remove the brackets for xing to the wall of studs with standard space

and follow the instructions for attaching the bracket to make the installation easier.

y

Install the product only on a vertical wall.

Do not install the bracket on a wall inclined at an angle, exceeding the standard range, or on the ceiling.

LG Electronics is not liable for any issues occurred due to the installation of the product on a slanted

wall or on the ceiling.

y

Check the accessories provided with the product before installing. LG Electronics is not liable for any

damage to or loss of the accessories after the package has been opened.

y

Keep the provided accessories out of reach of babies or children as it may cause safety issues,

including suffocation, from swallowing the parts.

y

Make sure that screws are installed securely on the wall.

Applying excessive force to screws may damage the wall, impair the performance or reduce the strength

of the product, or cause it to become damaged.

y

Be careful not to install a TV that exceeds the weight restrictions and not to apply external force.

y

Be careful when using the tools during installation to prevent accidents or damage.

Philips screwdriver (manual or electric) / 8 mm spanner / drill / Ф 8 mm drill bit for concrete wall Ф 4 mm drill

bit for wood or steel / level / stud nder / slotted screwdriver

6

ENG

ENGLISH

UNPACKING

VESA Guide Sheet

Installation Guide Tape

4 EA

User Manual Optical Cable

Guide Spacer (Bottom)

2 EA

Guide Spacer (Top)

2 EA

Guide Spacer (Top)

Fixing Screw

2 EA, M6 X 26

Guide Spacer (Bottom)

Fixing screw

2 EA, M4 X 20

Safety Clip (Top)

2 EA

Safety Clip (Bottom)

2 EA

Safety Clip (Top/

Bottom) Fixing screw

4 EA, M4 x 12

Set Protection

Cushion (Upper)

2 EA

(thickness: 11 mm)

Set Protection

Cushion (Bottom)

2 EA

(thickness: 1.5 mm)

Wall Mounting Anchor

8 EA

Wall Mounting Screw

8 EA

Rubber

2EA

(thickness: 12 mm)

7

ENGENGLISH

INSTALLATION

Attach the rubber here.

CAUTION

How to use the Rubber

y

It is recommanded to install the bracket on a concreate wall.

y

The product should be installed by a professional installer

designated by the retailer.

INSTALLATION

1

Attaching the Guide Spacer on the TV

y

If the screws cannot be fully tightened when xing the guide spacer with them, check the xing depth of

the screws again and refer to the technical service manual.

Guide Spacer (Top) Fixing Screw

Guide Spacer (Bottom) Fixing screw

Guide Spacer (Top)

Guide Spacer (Bottom)

< Procedures >

1 If any screws are installed into the mounting holes, please remove the screws.

2 Fix the guide spacers and the guide spacer xing screws in the order shown in the gure.

- Place the product facing down on a table. To prevent scratches on the screen, place the product on

a cushion or a soft clothes on a flat surface.

- Tighten the screw until the set, guide spacers and screws are joined together securely and stop

tightening.

- Use a Phillips driver (manual or electric) to tighten the screws.

8

ENG

ENGLISH

INSTALLATION

2

Attaching Set Protection Cushion

y

Attach the set protection cushion to mitigate the impact between the TV and the Canvas Speaker in

case of bumping against each other when adjusting the angle.

y

Attach the protection cushion to the four corners of the back of the set as shown in the gure.

Set Protection Cushion (Upper)

2 EA (thickness: 11 mm)

Set Protection Cushion (Bottom)

2 EA (thickness: 1.5 mm)

3

Checking the Spots for Fixing Screws on the Wall Using

VESA Guide Sheet

1430 mm

840 mm

(VESA guide sheet size)

865 mm

(Actual product size)

1 Check the VESA standard for the TV.

2 Mark the wall mounting location on the wall using the VESA guide sheet provided as an accessory.

3 Remove the VESA guide sheet after checking the spots for xing screws on the wall.

* Please note that the VESA guide sheet is shorter than actual product by 12.4 mm on the top and bottom

sides respectively, when installing the product.

9

ENGENGLISH

INSTALLATION

4

Fixing Anchors and Screws

< Please follow the directions below >

y

Check the material of the wall and thickness of nishing material.

y

You can use the anchors and screws provided with the TV set for the wall made with concrete,

lightweight concrete, soft eldstone, hard eldstone, brick or cellular block.

y

Do not mount on the wall made with plaster board or medium density breboard (MDF). Otherwise, you

must x the anchor screws to the retaining wall (concrete) inside the nishing material. If there is no

retaining wall, you must install a separate hanger rst to x the anchors and screws.

y

When installing the product on the wall that is not specied in this manual, make sure that each xing

point withstands an pullout load of 70 kgf (686 N) and a shearing load of 100 kgf (980 N) or more.

Wall mounting screw

Anchor

1 2

5

3

4

y

Use the Ø 8 mm drill bit for concrete wall and hammer (Impact) drill.

1 Use a Ø 8 mm drill bit to make a hole with a depth of 80-100 mm on the anchor position.

2 Clean the drilled holes.

3 Insert the provided anchor in the hole. (Use a hammer when inserting the anchor.)

4 Place the angle adjusting part to face upward. Place the angle adjusting part to face upward.

5 Align the wall mounting screws with the holes to tighten the screws. Tighten the screw using a

recommended torque of 45 kgf/cm - 60 kgf/cm or more.

5

Installing the Wall Mounting Supporter

y

Tighten the four wall mounting screws.

y

If the screws cannot be xed in the

designated location, move the bracket to

the left or right to x the screws.

y

Fix the wall mounting supporter using the

wall mounting screws as shown in the

gure.

y

Tighten the screws until the wall, the wall

mounting supporter and the screws are

joined together securely using a (manual

or electric) Phillips screwdriver or 8 mm

spanner.

Wall Mounting Screw

10

ENG

ENGLISH

INSTALLATION

6

Assembling the Wall Mounting Supporter and the

Canvas Speaker

< Two or more people are needed to lift and install the product >

Installation Guide Tape

1 Place the Canvas Speaker on the wall mounting attached to the wall in the direction of the arrow.

- Attach the guide tape for wall mounting above the left and right holes of the wall mounting and the left

and right VESA of the Canvas Speaker .

- Attach the guide tape for wall mounting side by side as shown in the figure and then install the

product. When the installation is complete, remove the guide tape for wall mounting.

- Check if the product is securely fixed by pulling ou the top of the Canvas Speaker

- If the product is not levelled after the installation, adjust the level by moving the Canvas Speaker left

and right.

Wall Mounting Screw

2 Install the wall mounting bracket using wall mounting screws.

11

ENGENGLISH

INSTALLATION

Safety Clip (Top) Fixing screw

Safety Clip (Top)

Assemble Safety Clip

between the Wall Mounting

Bracket and the Product

3 Hang the TV assembled with the guide spacers on the wall mounting bracket attached to the wall by

aligning it with the grooves of the bracket in the direction of the arrow. Attach the lower part rst, and

then attach the uppepart by slightly lifting up the set.

4 Insert the safety pin, which is provided in order to prevent the product desorption, in the direction of the

arrow while adjusting the position, and then completely x the safety clip with xing screw for safety clip.

If the safety pin is not xed as shown in the gure, the product may fall.

- Check if the product is securely fixed by pulling ou the bottom of the TV.

When using cables or accessories that are not provided as accessories for this product, make sure to

keep a certain distance from the wall so that excessive force is not applied on cables or accessories.

- Pushing the product with excessive force may cause damage to the product.

7

Adjusting the Level of the Product

y

If the product is not levelled after the installation, adjust the level using this screw.

(The product goes up or down, depending on the rotation direction of the screw.)

12

ENG

ENGLISH

INSTALLATION

8

Organizing the Power Cord

y

Pull the Canvas speaker forward.

y

Draw out the power cord through the square hole below the Canvas speaker to organize it.

< Back > < Front >

TV Power cord

Square hole

below the

Canvas Speaker

< Side >

13

ENGENGLISH

INSTALLATION

9

Fixing the Safety Clip (Bottom)

y

Be sure to x the safety clip (bottom) after organizing the power cord.

y

Fix the safety clip (bottom) using the safety clip xing screw in the wall mounting brackets square hole

as shown in the gure.

y

Fix the clip to make it symmetrical bilaterally.

y

Pull out the lower part of the canvas speaker to check if the product is securely xed.

Safety Clip Fixing screw

Combined Appearance of the wall

mounting brackets and canvas

speaker, Safety Clip

Safety Clip (Bottom)

10

Connecting the Optical Cable

< Front > < Side >

Optical Cable

CAUTION

y

Leave a 10 cm (minimum) space from the wall for proper

ventilation.

y

Do not place the TV near or on sources of heat, as this may

result in fire or other damage.

10 cm

Canvas Speaker

14

ENG

ENGLISH

INSTALLATION / PRODUCT SPECIFICATIONS

11

Combined Appearance of the Canvas Speaker and TV

Canvas Speaker

TV

PRODUCT SPECIFICATIONS

[ Unit : mm ]

° ~ °± °

145

° ~ °± °

145

TX\° ~ RX\°G ± Y°

145

14

Maximum Minimum

TX\° ~ RX\°G± Y°

145

14

TX\° ~ RX\°G± Y°

TX\° ~ RX\°G ± Y°

145

14

< Wall Mounting Bracket >

15

ENGENGLISH

PRODUCT SPECIFICATIONS

< Canvas Speaker >

< Wall Mounting Supporter >

Model Name Canvas Speaker

Wall Mounting

Bracket

Wall Mounting

Supporter

Width (mm) 1430 450 500

Height (mm) 865 500 64

Depth (mm)

64 40 9

Weight (kg)

17.7 5.7 0.6

Wall Mounting VESA

Specifications

-

210 (Top)

/ 364 (Bottom) * 450

-

Max.UL Load

Capacity(kg)

- 50 50

Audio Output 100 W - -

Power

AC 100V~240V 50~60Hz

(SMPS ADPATER)

- -

Input SPDIF input - -

Front, woofer Impedance: 8 Ω - -

www.lg.com

BENUTZERHANDBUCH

BILDSCHIRM-LAUTSPRECHER

Lesen Sie dieses Handbuch aufmerksam durch, bevor Sie Ihr Gerät

zum ersten Mal verwenden und bewahren Sie es zur späteren

Verwendung auf.

2

ENG

DEUTSCH

INHALTSVERZEICHNIS

3 SICHERHEITSVORKEHRUNGEN

5 VOR DER INSTALLATION ZU BEACHTEN

6 ZUBEHÖRTEILE

7 INSTALLATION

7 Anbringen des Abstandhalters am TV-Gerät

8 Anbringen des Polsterbandes

8 Überprüfen geeigneter Stellen zur Befestigung der Schrauben an der Wand unter Verwendung der

VESA - Schablone

9 Befestigung der Dübel und Schrauben

9 Montage der Wandhalterungsträger

10 Anbringen der Wandhalterungsträger und des Bildschirm-Lautsprechers

11 Ausrichten des Produkts

12 Ordnen des Netzkabels

13 Befestigen des Sicherheitsclips (unten)

13 Anschließen des Glasfaserkabels

14 Gemeinsame Darstellung des Bildschirm-Lautsprechers und des TV-Geräts

14 PRODUKTSPEZIFIKATIONEN

WARNUNG

y

Bei Nichtbeachtung drohen schwere Verletzungen, Unfälle und Tod.

VORSICHT

y

Bei Nichtbeachtung drohen leichte Verletzungen oder eine Beschädigung des Produkts.

3

ENGDEUTSCH

SICHERHEITSVORKEHRUNGEN

- Dieses Handbuch muss vor der Installation vom zuständigen Techniker gelesen werden.

- Nach der Installation sollte das Handbuch an den Kunden übergeben werden. Dieser sollte es sorgfältig

lesen und sicher aufbewahren.

Das Handbuch sollte nach dem Lesen für den weiteren Gebrauch an einem leicht zugänglichen Ort

aufbewahrt werden.

WARNUNG

Das Produkt sollte ausschließlich von einem

professionellen Techniker installiert werden,

der Ihnen von einem Händler zugewiesen

wurde.

Bei der Installation durch jede andere Person

besteht höchste Gefahr, und es kann zu

Körperverletzungen kommen.

Installieren Sie das Produkt nicht an einem mit

unzureichender Tragfähigkeit.

Wenn das Produkt an einem Ort installiert wird, der

nicht ausreichend stabil und fest ist, kann es u.U.

herunterfallen und Körperverletzungen verursachen.

Wenden Sie sich an einen vom Händler

empfohlenen Techniker, wenn Sie das Produkt

umpositionieren oder entfernen wollen.

Die Installation bedarf spezieller Vorgehensweisen.

Eigenständiges Umpositionieren oder Installieren kann

daher zu schwerwiegenden Sicherheitsproblemen

führen.

Setzen Sie das Produkt nach der Installation

keinerlei Zug- oder Druckbelastung aus.

Anderenfalls kann es passieren, dass es herunterfällt

und Verletzungen verursacht.

Hängen Sie bei Produkten, die an der

Wand montiert werden, nie das Netz- oder

Signalkabel auf die Rückseite des Fernsehers.

Anderenfalls kann es passieren, dass die Kabel

beschädigt werden, und Brand, Stromschläge oder

Produktbeschädigungen verursachen.

4

ENG

DEUTSCH

SICHERHEITSVORKEHRUNGEN

VORSICHT

Installieren Sie das Produkt gemäß den

Beschreibungen im Benutzerhandbuch.

Wenn Sie sich nicht an die Beschreibungen im

Benutzerhandbuch halten, kann es aufgrund

einer fehlerhaften Installation zu schweren

Körperverletzungen oder Beschädigungen des Produkts

kommen.

Zur Installation oder Höhenanpassung des

Produkts sind mindestens zwei Personen

erforderlich.

Anderenfalls kann es zu Körperverletzungen oder

Beschädigungen des Produkts kommen.

Überprüfen Sie vor der Installation die

Beschaffenheit der Wand, und verwenden Sie

zur Installation nur die beiliegenden Dübel und

Schrauben.

Andere als die vorgesehenen Dübel und Schrauben

halten u.U. dem Gewicht des Produkts nicht stand, was

zu Sicherheitsproblemen führen kann.

Verwenden Sie zum Bohren der Löcher stets

eine Bohrmaschine und einen Bohrer mit

passendem Durchmesser.

Wenn Sie sich beim Bohren der Löcher nicht an

die folgenden Beschreibungen halten, ist das

Produkt u.U. nicht stabil befestigt, und es kann zu

Sicherheitsproblemen kommen.

Wischen Sie das Produkt nie mit einem nassen

Tuch ab, und halten Sie es von Heizungen oder

Luftbefeuchtern fern.

Bei Kontakt mit Nässe, Feuchtigkeit oder Hitze

besteht die Gefahr von Brand, Stromschlägen oder

Fehlfunktionen.

Installieren Sie das Produkt nur an einer

senkrechten Wand und nie beispielsweise

in der Nähe eines Sprinklers oder Sensors,

an einem Ort, an dem es Erschütterungen

oder Schlägen ausgesetzt sein könnte bzw.

in der Nähe von Hochspannungskabeln oder

Stromquellen.

Ziehen Sie vor der Installation das Netzkabel

aus der Steckdose.

Wenn das Produkt bei eingestecktem Netzkabel

installiert wird, besteht Stromschlag- oder Brandgefahr.

Installieren Sie das Produkt nie mit bloßen

Händen. Tragen Sie stets geeignete

Arbeitshandschuhe.

Anderenfalls kann es zu Körperverletzungen kommen.

Wenn Sie zum Anschließen des Produkts

andere als die beiliegenden Kabel verwenden,

kann die Wand oder der Anschluss des

Produkts durch Reibung beschädigt werden.

Verwenden Sie ausschließlich die beiliegenden

Kabelkomponenten.

La pagina sta caricando ...

LG OCF100 Manuale utente

LG OCF100 Manuale utente

in altre lingue

Documenti correlati

Altri documenti