ProLights DIAMOND19TW Manuale utente

Categoria
Stroboscopi
Tipo
Manuale utente
DIAMOND19TW
LED MOVING HEAD
EN - IT
USER MANUAL
MANUALE UTENTE
All rights reserved by Music & Lights S.r.l. No part of this instruction manual may be
reproduced in any form or by any means for any commercial use.
In order to improve the quality of products, Music&Lights S.r.l. reserves the right to modify the
characteristics stated in this instruction manual at any time and without prior notice.
All revisions and updates are available in the ‘manuals section on site www.musiclights.it
REV. 03-11/18
1
DIAMOND19TW
TABLE OF CONTENTS
Safety
General instructions
Warnings and installation precautions
1 Introduction
1. 1 Description
1. 2 Technical specications
1. 3 Operating elements and connections
2 Installation
2. 1 Mounting
3 Functions and settings
3. 1 Operation
3. 2 Basic
3. 3 Menu structure
3. 4 Slave Receive mode
3. 5 Operation in automatic mode
3. 6 Scenes Record mode
3. 7 Music mode
3. 8 Sensitivity microphone
3. 9 Linking
3. 10 DMX mode
3. 11 DMX conguration
3. 12 DMX addressing
3. 13 Connection of the DMX line
3. 14 Construction of the DMX termination
3. 15 DMX control
3. 16 Wireless control settings
3. 17 Fixture settings
3. 18 Lamp settings
3. 19 Display settings
3. 20 Fixture information
3. 21 Reset functions
3. 22 Special functions
4 Maintenance
4. 1 Maintenance and cleaning the unit
4. 2 Fuse replacement
4. 3 Trouble shooting
2
2
3
3
5
6
7
7
8
10
11
12
12
13
13
13
13
14
15
15
16
19
19
19
20
20
21
21
24
24
25
DIAMOND19TW
Mount bracket
Power supply cable and signal cable
Safety rope
User manual
Packing content
DIAMOND19TW
2
WARNING! Before carrying out any operations with the unit, carefully read this instruction
manual and keep it with cure for future reference. It contains important information about
the installation, usage and maintenance of the unit.
SAFETY
General instruction
The products referred to in this manual conform to the European Community Directives and are there-
fore marked with .
The unit is supplied with hazardous network voltage (230V~). Leave servicing to skilled personnel only.
Never make any modications on the unit not described in this instruction manual, otherwise you will
risk an electric shock.
Connection must be made to a power supply system tted with ecient earthing (Class I appliance ac-
cording to standard EN 60598-1). It is, moreover, recommended to protect the supply lines of the units
from indirect contact and/or shorting to earth by using appropriately sized residual current devices.
The connection to the main network of electric distribution must be carried out by a qualied electrical
installer. Check that the main frequency and voltage correspond to those for which the unit is designed
as given on the electrical data label.
This unit is not for home use, only professional applications.
Never use the xture under the following conditions:
- in places wet;
- in places subject to vibrations or bumps;
- in places with an ambient temperature of over 45°C.
Make certain that no inammable liquids, water or metal objects enter the xture.
Do not dismantle or modify the xture.
All work must always be carried out by qualied technical personnel. Contact the nearest sales point for
an inspection or contact the manufacturer directly.
If the unit is to be put out of operation denitively, take it to a local recycling
plant for a disposal which is not harmful to the environment.
Warnings and installation precautions
If this device will be operated in any way dierent to the one described in this manual, it may suer
damage and the guarantee becomes void. Furthermore, any other operation may lead to dangers like
short circuit, burns, electric shock, etc.
Before starting any maintenance work or cleaning the projector, cut o power from the main supply.
Always additionally secure the projector with the safety rope. When carrying out any work, always com-
ply scrupulously with all the regulations (particularly regarding safety) currently in force in the country
in which the xture’s being used.
For inside use only. Not designed for outside use.
The minimum distance between the xture and surrounding walls must be more than 50 cm and the
air vents at the housing must not be covered in any case.
Install the xture in a well ventilated place.
Keep any inammable material at a safe distance from the xture.
The maximum temperature that can be reached on the external surface of the tting, in a thermally
steady state, is high. After power o, please cool down over 15 minutes.
Shields, lenses or ultraviolet screens shall be changed if they have become damaged to such an extent
that their eectiveness is impaired.
The lamp (LED) shall be changed if it has become damaged or thermally deformed.
Never look directly at the light beam. Please note that fast changes in lighting, e. g. ashing light, may
trigger epileptic seizures in photosensitive persons or persons with epilepsy.
3
DIAMOND19TW
- 1 - INTRODUCTION
1.1 DESCRIPTION
DIAMOND19TW is a tunable white version of the stunning DIAMOND19 delivering a consistent 2600K-
8000K output. The 6-66° zoom, even beam and precise colour calibration create a true workhorse xture
for an exhibition, corporate or broadcast environment.
1.2 TECHNICAL SPECIFICATIONS
LIGHT SOURCE
Source: 19x15W warm white + cold white Osram Ostar LED
CT: 2600~8000K
CRI: 70-90
Luminous ux: 9000lm
Lux: (6°) 11805 - (66°) 1239lux @5m
Source life expectancy: >50.000 h
OPTICS
Zoom: 6-66° motorised linear zoom
Lens type: honeycomb gapless plano-convex optics
COLOUR SYSTEM
Colour mixing: tunable white
CTC: CTC control through independent DMX channel
White presets: 2600~8000K
Colour wheel: built-in white presets
BODY
Pan angle: 630°
Tilt angle: 265°
Pan/Tilt resolution: bit 8/16 bit
Feedback: automatic repositioning after accidental movement
Body: aluminium structure with hi-resistance polycarbonate cover
Body colour: black
CONTROL
Protocols: DMX512, RDM
DMX channels: 12/13/14/20channel
W-DMX: included, wireless solution receiver
RDM: RDM ready for xture remote monitor and settings
Display: LCD high resolution colour display
Firmware upgrade: yes, via USB-DMX interface (UPBOX2) not included
Hibernation: power safe mode when lost DMX
Master/Slave: for synchronized operation of more units linked in a chain
ELECTRONICS
Dimmer: linear 0~100% electronic dimmer
Strobe / shutter: 1-25 Hz, electronic
Battery backup: battery backup for user operation without connecting to the main power
DIAMOND19TW
4
Operating temperature: -10° ~ +45°
Flicker: icker free operation
ELECTRICAL
Power supply: 100-240V – 50/60Hz
Power consumption (at 230V): 316W
Output (at 230V): 6 units on a single power line
PHYSICAL
Cooling: combination of heat pipe cooling system and low noise fan
Sospension and xing: any position with quick-lock omega brackets
Signal connection: Amphenol XLR 3p IN/OUT connectors
Power connection: Neutrik powerCON IN/OUT connectors
IP rating: 20
Dimensions (WxHxD): 338x449x235mm
Weight: 11kg
Fig.1
Photometric dataTechnical drawing
Illuminance at a Distance
6°- 66°
3m
5.0m
7.5m
0m
0.54/4.04m
0.54/4.04m
Lux Center Beam Angle: 6°- 66° Beam Width
WW12500/1137lx
CW20560/1890lx
0.75/6.59m
0.75/6.59m
WW4445/467lx
CW7360/772lx
1.01/9.78m
1.01/9.78m
WW2005/218lx
CW3359/348lx
449
338
235
5
DIAMOND19TW
1. MOVING HEAD
2. ROTARY ARM
3. HANDLE
4. LED INDICATOR "WDMX"
5. MICROPHONE
6. CONTROL PANEL with LCD display
and 5 button used to access
the control panel functions and
manage them.
7. DMX OUT ( 3-pole XLR):
1 = ground, 2 = DMX -, 3 = DMX +
8. DMX IN (3-pole XLR):
1 = ground, 2 = DMX -, 3 = DMX +
9. DMX OUT (5-pole XLR):
1 = ground, 2 = DMX-, 3 = DMX+,
4 N/C, 5 N/C
10. DMX IN (5-pole XLR):
1 = ground, 2 = DMX-, 3 = DMX+,
4 N/C, 5 N/C
11. POWER IN (PowerCON IN):
for connection to a socket
(100-240V~/50-60Hz) via the
supplied mains cable.
12. POWER OUT (PowerCON OUT):
power output for connection of
multiple units in series.
13. MAIN FUSE HOLDER: replace a
burnt-out fuse by one of the same
type only.
1.3 OPERATING ELEMENTS AND CONNECTIONS
Fig.2
View A
View B
4
A
B
1
2
3
5 6
7 9 11
8 10 1312
DIAMOND19TW
6
- 2 - INSTALLATION
2.1 MOUNTING
The DIAMOND19TW may be set up on a solid and even surface. By means of the xing facilities of the
baseplate, the unit can also be mounted upside down to a cross arm. The base plate is shown in g.3. For
xing, stable mounting clips are required. According to the gure, the bolts of the brackets are placed into
the openings provided in the base plate and turned clockwise until they lock (to the stop). Always ensure
that the unit is rmly xed to avoid vibration and slipping while operating. The mounting place must be of
sucient stability and be able to support a weight of 10 times of the units weight. When carrying out any
installation, always comply scrupulously with all the regulations (particularly regarding safety) currently
in force in the country in which the xture’s being used. Always additionally secure the projector with the
safety rope from falling down. For this purpose, fasten the safety rope at a suitable position so that the
maximum fall of the projector will be 20 cm.
Fig.3
CLAMP
SAFETY
CABLE
OMEGA
BRACKETS
7
DIAMOND19TW
- 3 - FUNCTIONS AND SETTINGS
3.1 OPERATION
Connect the supplied main cable to a socket (100-240V~/50-60Hz). The unit will run built-in program to
reset all motors to their home position. Shortly after that the DIAMOND19TW is ready for operation. To
switch o, disconnect the mains plug from the socket. For a more convenient operation it is recommend-
ed to connect the unit to a socket which can be switched on and o via light switch.
3.2 BASIC
The DIAMOND19TW has a LCD display and 5 button used to access the control panel functions and man-
age them (g.4).
Fig.4 - Functions of the buttons and display icons
LEFT RIGHT UP DOWN ENTER BATTERY
Return to the top
level
Commute from
units, tens, hundred
in the menu
Increases the value
displayed or passes
to the previous item
in a menu
Decreases the value
displayed or passes
to the next item in
the menu
Conrms the
displayed value,
or activates the
displayed function,
or enters the
successive menu
Used to activate the
backup battery. It
allows to switching
display interface
without main power
CONNECT
LIGHT
INFORMATION
SET
PROGRAM
Battery
DIAMOND19TW
8
3.3 MENU STRUCTURE
MENU
1 Connect
ð
DMX Address
ð
Value (1-512)
Wireless DMX
ð
Value (1-512)
2 Light
ð
Max Temperature
ð
Value (60°-130° C)
Lamp Adjust
ð
Control
ð
Value (000-255)
Pan
ð
Value (000-255)
Pan Fine
ð
Value (000-255)
Tilt
ð
Value (000-255)
Tilt Fine
ð
Value (000-255)
Pan&Tilt Speed
ð
Value (000-255)
Pan&Tilt Fun
ð
Value (000-255)
Shutter Fun
ð
Value (000-255)
Shutter
ð
Value (000-255)
Dimmer
ð
Value (000-255)
Color Function
ð
Value (000-255)
Virtual Color1
ð
Value (000-255)
Virtual Color2
ð
Value (000-255)
Warm White All
ð
Value (000-255)
Cool White All
ð
Value (000-255)
Zoom
ð
Value (000-255)
Foreground
ð
Value (000-255)
Background
ð
Value (000-255)
Pattern
ð
Value (000-255)
Pattern Speed
ð
Value (000-255)
Pattern Byte 1
ð
Value (000-255)
Pattern Byte 2
ð
Value (000-255)
Pattern Byte 3
ð
Value (000-255)
Pattern Byte 4
ð
Value (000-255)
Pattern Byte 5
ð
Value (000-255)
3 Information
ð
Time Info.
Temperature
Fans Speed
Channel Value
Error Message
Fixture Model
Software Ver.
9
DIAMOND19TW
4 Set
ð
Reset
ð
All
Pan & Tilt
Others
Movement
ð
Pan Reverse
ð
ON/OFF
Tilt Reverse
ð
ON/OFF
Pan Degree
ð
540/630
Encoders
ð
ON/OFF
Pan/Tilt Mode
ð
Standard/Smooth
UI Set
ð
Mic Sens.
ð
Value (00-99%)
No Signal
ð
Close/Hold/Auto/Music
Temperature C/F
ð
Celsius/Fahrenheit
Fans Mode
ð
Auto Speed/High Speed
Zoom Mode
ð
Mode1 /Mode2
Hibernation
ð
Not Hibernation/Min (01-99)
Backlight
ð
Always On/Min (01-99)
Flip Display
ð
ON/OFF
Display Bright
ð
Value (00-31)
Brand Show
ð
ON/OFF
Key Lock
ð
ON/OFF
Language
ð
EN/FR/SP...
Fixture Set
ð
Theater Mode
ð
ON/OFF
Frequency
ð
600/1200/2000/2400/4000 Hz/25 kHz
Users
ð
User Mode
ð
Standard/Extended/Basic-8bit/Basic-16bit
Edit User
ð
Max Channel/Control/Pan/Pan Fine/Tilt/Tilt Fine...
Calibration
ð
Password
ð
050 (insert to unlock the following settings)
Pan
ð
Value (-128-127)
Tilt
ð
Value (-128-127)
Red-All
ð
Value (XXX)
Green-All
ð
Value (XXX)
Blue-All
ð
Value (XXX)
Fixture ID
ð
Name
ð
Fixture ID Name
RDM Mode
Password
ð
050 (insert to unlock the following settings)
PID Code
ð
00001
Wireless Set
ð
DMX On Cable
ð
ON/OFF
Reset Connect
ð
ON/OFF
Reload Default
ð
Basic Reload
ð
ON/OFF
DIAMOND19TW
10
3.4 SLAVE RECEIVE MODE
This mode will allow you to link up the units together without a controller. Choose a unit to function as the
Master. The unit must be the rst unit in line; other units will work as slave with the same eect.
A Master unit can send up to 3 dierent data groups to the Slave units, i.e. a Master unit can start 3 dier-
ent Slave units, which run 3 dierent programs. The Master unit sends the 3 program parts in a continuous
loop.
The Slave unit receives data from the Master unit according to the group which the Slave unit was as-
signed to.
For example, if a slave device is set to Receive Part 1, the Master unit Slave unit will send the automated
Chase Part 1; if set to Receive Part 2, the Chase Part 2 Slave units will receive from the Master.
To set the drive as a slave, proceed as follows:
Press the ENTER button to access the main menu.
Press the UP/DOWN button to scroll the menu, select the Program icon, then press the ENTER button to
enter the next menu.
Press the UP/DOWN button to scroll through the menu, and then select Play and press the ENTER
button to enter the next menu.
Press the UP/DOWN button to scroll through the menu, and select Slave Receive and press ENTER to
conrm.
Press the UP/DOWN button to select the dierent modes of operation Part 1 Receive/Receive Part 2/Part 3
Receive, and then press the ENTER button to conrm your choice.
Press the LEFT button repeatedly to exit the menu and save changes.
Program Reload
ð
ON/OFF
Password
ð
050 (insert to unlock the following settings)
Private Reload
ð
ON/OFF
All Reload
ð
ON/OFF
5 Program
ð
Play
ð
DMX Receive
Slave Receive
ð
Part 1 Receive/Part 2 Receive/Part 3 Receive
Sequence
ð
Alone/Master
Music
ð
Alone/Master
Select Chase
ð
Chase Part 1
ð
Chase 1 - Chase 8
Chase Part 2
ð
Chase 1 - Chase 8
Chase Part 3
ð
Chase 1 - Chase 8
Edit Chases
ð
Edit Chase 1
ð
Chase Test/ Step 1 - Step 64
Edit Chase 2
ð
Chase Test/ Step 1 - Step 64
Edit Chase ...
ð
Chase Test/ Step 1 - Step 64
Edit Chase 8
ð
Chase Test/ Step 1 - Step 64
Edit Scenes
ð
Edit Scenes 001
ð
Control/.../Fade Time/Scene Time/External Input
Edit Scenes 002
ð
Control/Pan/Pan Fine/Tilt/Tilt Fine...
Edit Scenes ...
ð
Control/Pan/Pan Fine/Tilt/Tilt Fine...
Edit Scenes 250
ð
Control/Pan/Pan Fine/Tilt/Tilt Fine...
Scenes Record
ð
Sc XX - Sc XX
11
DIAMOND19TW
Select the desired program on the master unit (described in section 3.5).
Use the DMX connectors of the DIAMOND19TW and an XLR cable to form a chain of units. Under certain
conditions and lengths you want to make a termination as shown on page 16.
3.5 OPERATIONS IN AUTOMATIC MODE
The unit independently runs through its show. Before you send an automatic program you need to set the
drive as Master/Alone:
Press the ENTER button to access the main menu.
Press the UP/DOWN button to scroll the menu, select the Program icon, then press the ENTER button to
enter the next menu.
Press the UP/DOWN button to scroll through the menu, select Play and press the ENTER button to enter
the next menu.
Press the UP/DOWN button to scroll through the menu, select Sequence and press ENTER to conrm
your choice.
Press the UP/DOWN button to select the mode of operation:
- Master, if the unit is connected in series with other units and it acts as the Master;
- Alone, if the unit is not connected to other units.
Press the ENTER button to conrm your choice.
Press the LEFT button repeatedly to exit the menu and save changes.
The unit will go into automatic mode by executing the program automatically.
Select Chase
The function Select Chase lets you choose the automatic program to actually run.
Press the ENTER button to access the main menu.
Press the UP/DOWN button to scroll the menu, select the Program icon, then press the ENTER button to
enter the next menu.
Press the UP/DOWN button to scroll through the menu, select Select Chase and press the ENTER button
to enter the next menu.
Press the UP/DOWN button to scroll through the menu, then select Chase Part 1/Chase Part 2/Chase Part 3
and press ENTER to conrm.
Press the UP/DOWN button to select Chase1-Chase8, and press the ENTER button to conrm.
Press the LEFT button repeatedly to exit the menu and save changes.
Edit Chases
The function Edit Chases allows you to create automatic pre-programmed show.
The automatic programs Chase Part1/2/3 are each divided into Chase1-Chase8. Each Chase can be composed
of 1-64 step that can be congured through the following procedure:
Press the ENTER button to access the main menu.
Press the UP/DOWN button to scroll the menu, select the Program icon, then press the ENTER button to
enter the next menu.
Press the UP/DOWN button to scroll through the menu, select Edit Chases and press the ENTER button
to enter the next menu.
Press the UP/DOWN button to scroll through the menu, select Edit Chase 1 - Edit Chase 8, then press the
ENTER button to conrm.
Press the UP/DOWN button to select the Step 01 - Step 64, and press ENTER to conrm.
Press the UP/DOWN button to select the Scene you want to set for the Step chosen, and then press
ENTER to conrm.
Press the LEFT button repeatedly to exit the menu and save changes.
DIAMOND19TW
12
Edit Scenes
The function Edit Scenes allows you to create individual scenes to be included in the Chase Step.
Press the ENTER button to access the main menu.
Press the UP/DOWN button to scroll the menu, select the Program icon, then press the ENTER button to
enter the next menu.
Press the UP/DOWN button to scroll through the menu, select Edit Scenes and press the ENTER button
to enter the next menu.
Press the UP/DOWN button to scroll through the menu, select Edit Scene 001 - Edit Scene 250, then press the
ENTER button to conrm.
Press the UP/DOWN button to select the desired function you want to edit (Control, Pan, Tilt, etc..), Then
press the ENTER button to conrm.
Press the UP/DOWN button to change the value of the function, then press the ENTER button to
conrm.
Press the LEFT button repeatedly to exit the menu and save changes.
3.6 SCENES RECORD MODE
DIAMOND19TW is equipped with a built-in DMX recorder by which you can transmit the programmed
scenes from your DMX-controller to the device. Proceed as follows to store the sequence of scenes in the
unit.
Press the ENTER button to access the main menu.
Press the UP/DOWN button to scroll through the menu, select the Program icon, then press the ENTER
button to enter the next menu.
Press the UP/DOWN button to scroll through the menu, select Scenes Record and press the ENTER button
to enter the next menu.
Press the UP/DOWN button to adjust the scene at the beginning and end to be inserted in the auto-
matic program, then press the ENTER button to conrm.
Press the LEFT button repeatedly to exit the menu and save changes.
When recalling scenes from the controller will automatically be transmitted to the device.
3.7 MUSIC MODE
In music mode, via its integrated microphone, the unit can be controlled by music with a clear rhythm in
the bass range. If the music control should not work optimally, increase the volume or reduce the distance
between the sound source and the light eect unit or alternatively increase the sensitivity of the micro-
phone.
Press the ENTER button to access the main menu.
Press the UP/DOWN button to scroll the menu, select the Program icon, then press the ENTER button to
enter the next menu.
Press the UP/DOWN button to scroll through the menu, select Play and press the ENTER button to enter
the next menu.
Press the UP/DOWN button to scroll through the menu, select Music and press ENTER to conrm.
Press the UP/DOWN button to select the mode of operation:
- Master, if the mobile head is connected in series to other units, and it performs the Master function;
- Alone, if the xture is not connected to other units.
Press the ENTER button to conrm your choice.
Press the LEFT button repeatedly to exit the menu and save changes.
The unit will go into music mode by executing an automatic program to the rhythm of music.
13
DIAMOND19TW
3.8 SENSITIVITY MICROPHONE
Select this function to set the value of the sensitivity of the microphone for use with a music control:
Press the ENTER button to access the main menu.
Press the UP/DOWN button to scroll the menu, select the Set icon, then press the ENTER button to enter
the next menu.
Press the UP/DOWN button to scroll through the menu, select UI Set, and press the ENTER button to
enter the next menu.
Press the UP/DOWN button to scroll through the menu, then select Mic Sens. and press ENTER to conrm.
Press the UP/DOWN button to adjust the level of sensitivity of the microphone, and then press the
ENTER button to conrm your choice.
Press the LEFT button repeatedly to exit the menu and save changes.
3.9 LINKING
Several units may be interconnected in order to control all further slave units to the same eect of the
master unit.
1. Connect the DMX OUT of the master unit via 3/5-pole XLR cable to the DMX IN of the rst slave unit.
2. Connect the DMX OUT of the rst slave unit to the DMX IN of the second slave unit, etc. until all units
are connected in a chain.
3.10 DMX MODE
To enter the DMX mode, follow these steps:
Press the ENTER button to access the main menu.
Press the UP/DOWN button to scroll the menu, select the Connect icon, then press the ENTER button to
enter the next menu.
Press the UP/DOWN button to scroll through the menu, select the DMX Address and press the ENTER key.
Press the arrow keys to select the desired value (001-512). Press the ENTER key to conrm the setting.
Press the LEFT button repeatedly to exit the menu and save changes.
3.11 DMX CONFIGURATION
The DIAMOND19TW has 5 DMX channel congurations which can be accessed from the control panel.
Press the ENTER button to access the main menu.
Press the UP/DOWN button to scroll the menu, select the Set icon, then press the ENTER button to enter
the next menu.
Press the UP/DOWN button to scroll through the menu, select Users and press the ENTER button to
enter the next menu.
Press the UP/DOWN button to scroll through the menu, select User Mode and press ENTER to conrm
your choice.
Use the UP/DOWN button to select the desired DMX channel conguration (Standard, Extended1, Basic-
8bit, Basic-16bit, User), then press the ENTER button to conrm your choice.
Press the LEFT button repeatedly to exit the menu and save changes.
The tables on page 17 show the mode of operation and their values DMX.
The unit is equipped with 3/5-pole XLR connections.
Edit User
The Edit User, in the same menu, allows you to create a prole of personalized functions. You can change
the parameters of the various functions (Control, Pan, Tilt, etc.). Once you’ve created your custom prole,
you can use it by selecting the USER mode as described above.
DIAMOND19TW
14
3.12 DMX ADDRESSING
For operation via light control unit with DMX512 protocol, is sucient connect the controller to DIA-
MOND19TW. To able to operate the DIAMOND19TW with a light controller, adjust the DMX start address
for the rst a DMX channel. If e. g. address 33 on the controller is provided for controlling the function of
the rst DMX channel, adjust the start address 33 on the DIAMOND19TW. The other functions of the light
eect panel are then automatically assigned to the following addresses.
An example with the start address 33 is shown below:
Number of
DMX channels
Start address
(example)
DMX Address
occupied
Next possible start
address for unit No. 1
Next possible start
address for unit No. 2
Next possible start
address for unit No. 3
12 33 33-44 45 57 69
13 33 33-45 46 59 72
14 33 33-46 47 61 75
20 33 33-52 53 73 93
Fig.5 - Example 15 DMX channels conguration
DMX Address: 78DMX Address: 48DMX Address: 33 DMX Address: 63
. . . . . . . . . . . .
DMX512 Controller
15
DIAMOND19TW
Fig.6
Fig.7
3.13 CONNECTION OF THE DMX LINE
DMX connection employs standard XLR connectors. Use shielded pair-twisted cables with 120Ω imped-
ance and low capacity.
The following diagram shows the connection mode:
ATTENTION
The screened parts of the cable (sleeve) must never be connected to the system’s earth, as this would
cause faulty xture and controller operation.
Over long runs can be necessary to insert a DMX level matching amplier.
For those connections the use of balanced microphone cable is not recommended because it cannot
transmit control DMX data reliably.
Connect the controller DMX input to the DMX output of the rst unit.
Connect the DMX output to the DMX input of the following unit. Connect again the output to the input
of the following unit until all the units are connected in chain.
When the signal cable has to run longer distance is recommended to insert a DMX termination on the
last unit.
3.14 CONSTRUCTION OF THE DMX TERMINATION
The termination avoids the risk of DMX 512 signals being reected back along the cable when they reach-
es the end of the line: under certain conditions and with certain cable lengths, this could cause them to
cancel the original signals.
The termination is prepared by soldering a 120Ω 1/4 W resistor between pins 2 and 3 of the 5-pin male XLR
connector, as shown in gure.
DMX - OUTPUT
XLR socket
DMX - INPUT
XLR plug
Pin1 : GND - Shield
Pin2 : - Negative
Pin3 : + Positive
Pin4 : N/C
Pin5 : N/C
Example:
3 pin XLR connector
DIAMOND19TW
16
3.15 DMX CONTROL
STAND EXT-1 BAS-8 BAS-16
FUNCTION DMX
Value
13 Ch 20 Ch 12 Ch 14 Ch
1 1 1 1
PAN
0~100% 000 - 255
2 2
PAN FINE
0~100% 000 - 255
2 3 2 3
TILT
0~100% 000 - 255
4 4
TILT FINE
0~100% 000 - 255
3 5 3 5
MOVEMENT SPEED
Fastest to slowest 000 - 255
6
MOVEMENT FUNCTION
Normal
Movement with backout
TBD
000 - 015
016 - 031
032 - 255
4 7
SHUTTER FUNCTION
Normal Shutter Functions
Pulse-eect Forward
Pulse-eect Reverse
Random strobe
TBD
000 - 015
016 - 031
032 - 047
048 - 063
064 - 255
5 8
SHUTTER
Normal Shutter Functions
Close
Strobe Rate (slow to fast)
Open
Pulse-eect Forward
Close
Strobe Rate (slow to fast)
Open
Pulse-eect Reverse
Close
Strobe Rate (slow to fast)
Open
Random Strobe
Close
Strobe Rate (slow to fast)
Open
000 - 031
032 - 223
224 - 255
000 - 031
032 - 223
224 - 255
000 - 031
032 - 223
224 - 255
000 - 031
032 - 223
224 - 255
4 6
SHUTTER
Shutter closed
No function (shutter open)
Strobe eect slow to fast
000 - 031
032 - 063
064 - 095
17
DIAMOND19TW
STAND EXT-1 BAS-8 BAS-16
FUNCTION DMX
Value
13 Ch 20 Ch 12 Ch 14 Ch
4 6
No function (shutter open)
Pulse-eect in sequences
No function (shutter open)
Random strobe eect slow to fast
No function (shutter open)
096 - 127
128 - 159
160 - 191
192 - 223
224 - 255
6 9 5 7
DIMMER
Dimmer (close to open) 000 - 255
7 10 6 8
VIRTUAL COLOR FUNCTION
On Function
CTC Function
Forward Spin
Reverse Spin
Continuous
Color Bounce
TBD
000 - 015
016 - 031
032 - 047
048 - 063
064 - 079
080 - 111
112 - 255
8 11 7 9
VIRTUAL COLOR 1
CTC Function
Color Temperature Correction 2800K->6300K
White 2800K
White 3200K
White 3800K
White 4200K
White 4600K
White 5000K
White 5600K
White 6300K
Forward Spin
Rainbow Eect (Slow to Fast)
Reverse Spin
Rainbow Eect (Slow to Fast)
Continuous & Color Bounce
Black
Warm White
Cool White
Warm White->Cool White->Warm White
000 - 223
224 - 227
228 - 231
232 - 235
236 - 239
240 - 243
244 - 247
248 - 251
252 - 255
000 - 255
000 - 255
000 - 000
001 - 002
003 - 004
005 - 255
9 12 8 10
VIRTUAL COLOR 2 (Only on Color Bounce)
Color Bounce
Black
Warm White
000 - 000
001 - 002
DIAMOND19TW
18
Fig.8 - LEDs numbering
12
3 4
5
6
8
9
10
13
14
15
1718
19
11
12
7
16
STAND EXT-1 BAS-8 BAS-16
FUNCTION DMX
Value
13 Ch 20 Ch 12 Ch 14 Ch
9 12 8 10
Cool White
Warm White->Cool White
003 - 004
005 - 255
10 13 9 11
WARM WHITE-ALL
WarmWhite 0 -> 100% 000 - 255
11 14 10 12
COOL WHITE-ALL
Cool White 0 -> 100% 000 - 255
12 15 11 13
ZOOM
Big angle -> Small angle 000 - 255
16
WARM WHITE-1
WarmWhite 0 -> 100% 000 - 255
17
COOL WHITE-1
Cool White 0 -> 100% 000 - 255
18
WARM WHITE-2
WarmWhite 0 -> 100% 000 - 255
19
COOL WHITE-2
Cool White 0 -> 100% 000 - 255
13 20 12 14
CONTROL
Normal
Reset All
Pan&Tilt Reset
TBD
Other Reset
Display O
Display On
TBD
TBD
Hibernation
TBD
000 - 007
008 - 015
016 - 023
024 - 047
048 - 055
056 - 063
064 - 071
072 - 079
080 - 087
088 -095
096 - 255
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56

ProLights DIAMOND19TW Manuale utente

Categoria
Stroboscopi
Tipo
Manuale utente

in altre lingue