udiR C UDI021 Remote Control Boat Guida utente

Marca
udiR C
Modello
UDI021 Remote Control Boat
Tipo
Guida utente
Li-Po Battery Disposal & Recycling
Wasted Lithium-Polymer batteries must not be placed with household
trash. Please contact local environmentalor waste agency or the
supplier of your model or your nearest Li-Po battery recycling center.
Our company's products are improving all the time, design and specifications are subject
to change without notice. All the information in this manual has been carefully checked to
ensure accuracy, if any printing errors, our company reserve the final interpretation right.
Important
Notice
This product is suitable for users over 14 years old.
Stay away from the rotating propeller
Read the “important statement and safety guidelines” carefully.
https://udirc.com/disclaimer-and-safety-instructions
Note
UDI021
Suitable for sailing in larger waters
OPERATION GUIDE
Deck
Hull bottom
Outlet
Cabin outer cover
Outer cover lock
Tail rudder
Propeller
Spindle tube
Support bracket
Power Switch
Buckle
Left navigation
Right navigation
Navigation Lights Cover
Navigation Lights
Battery Compartments
Tail rudder Bracket
Rods
Ready before sailing
Preparation the boat
Water press pieces
Head Cover Installation
Align the head cover with the bottom hole of the boat and install it in the right place.
02
Battery Charge
Connect the charging case to the charging input port of the boat battery and then connect the USB
output ports. The green indicator light flashes when charging and the green indicator light will keep
bright fully charged. During the charging, battery should not be placed in the hull when charging
and must be cooled before charging.
USB adapter (Not Include)
Battery power is insufficient in the original plant. It must be charged saturated before it can be used.
②①
Battery
input port Charger for Li battery case
powercharging
Boat battery
Warning: Must be supervised while charging
Please use the included USB charging cable and make sure it is properly connected.
Boat battery installation method
1) Twist to left or right to open the outer cover lock. 2) Open up the cabin cover.
3) According to the mark on the surface of the inner cover, unlock the lock and take out the inner
cover upward.
Cabin Inner
Cover
03
4) Put the Li-po battery into the boat battery holder.
the power line of the battery puts on the side of the
hull, push the battery to the end and stick to it.
6) Cover the inside and outside of the cabin and lock tightly.
5) Properly connected the hull input port
to the output port of the Boat battery.
Battery output port Hull input port
Navigation Lights Installation
1) Press the buckle inward
2) Take out navigation
lights cover
Back of
cabin cover
Press the " " to turn on the power.
Press again to select different lights.
Long press the switch for 2 senconds
to turn off the power.
3) Press the navigation
light into the corresponding
buckle position.
Buckle
position.
When the navigation light in low battery, the lamp will keep flashing.
It indicates the operator to replace the battery.
04
Transmitter Preparation
Steering Wheel
Throttle Trigger
Forward Trim
Backward Trim
Power Indicator
Left Rudder Trim
Right Rudder Trim
Power Switch
If the boat drifts to
the right, press the
left rudder trim on the
transmitter and the boat
will gradually correct
the rudder alignment. It
will start moving straight.
If the boat drifts to
the left, press the
right rudder trim on
the transmitter and
the boat will gradually
correct therudder
alignment. It will start
moving straight.
Left Rudder Trim Right Rudder Trim
If the boat still moves
backwards when the
throttle trigger is in the
middle position, press
forward trim until the
boat stops going
backwards.
Forward trim
If the boat still moves
forward when the
throttle trigger is in the
middle position, press
backward trim until the
boat stops going
forward.
Backward Trim
05
Battery installation of transmitter
Bottom of Transmitter
4×1.5V AA,
Alkaline Batteries
Open the transmitter battery cover. Install batteries. Follow the direction of batteries designated in
the inside of the battery box.
Note Direction.
Battery Cover
Please make sure the transmitter throttle trigger and
Steering wheel to normal.
It is recommended to be familiar with the operation on the surface of the water before long
distance navigation.
Sailing Operation
Frequency Pairing
1) Power on the transmitter, will sound "di", and the indicator light flashes, then to enter frequency
pairing.
2) After the boat battery is installed and powered on, tighten the hatch cover.
3) Put the boat into the water, the transmitter will sound "didi", and the indicator will keep long
bright it means frequency pairing successful.
06
Go forward Go backward
Throttle
trigger
Throttle
trigger
Manipulation method
Go forward Go forward
Throttle trigger Throttle trigger
Turn left Turn right
Steering wheel Steering wheel
Low speed High speed
Pull the throttle trigger
back gently and the car
will move forward slowly.
The throttle trigger is
pulled to the maximum,
and thecar moves
forward quickly.
If the boat capsizes, Push forward
and backward the throttle trigger of
the transmitter and then pull back at
once. The boat will then return to
normal, the capsize reset function will
turn off automatically when the boat in
low battery.
Self-Righting Hull
07
Low Battery Alarm
Out of Range Alarm
The motor lowers the temperature by flowing water. During the voyage, water flows through the
heat pipe around the motor, which has a cooling effect on the motor.
Water cooling system
Boat: When the boat in low battery, the transmitter will beep "di.di.di. ..." constantly to remind the
user to remote back the boat as soon as possible. And the boat speed will slow down to half
and the capsize reset function will turn off automatically when the boat in low battery.
Transmitter: When the transmitter in low battery, the transmitter will beep "di.di.di. ..." to remind
the user to remote back the boat to replace the batteries as soon as possible.
When the boat is running out of the max remote control distance, the transmitter will beep
"didi...didi..." to alarm the user to remote back the boat immediately.
Safety Precautions
1) Turn on the transmitter power first and then turn on the boat power before playing; Turn off the
boat power first and then turn off the transmitter power when finish playing.
2) Make sure the connection is solid between battery and motor etc. The ongoing vibration may
cause bad connection of power terminal.
3) Improper operation may cause impact to the boat and damage the hull or propeller.
4) It is forbidden to sail in the water where people are useful and sail away from salt water and
sundry water.
5) The battery must be take out after playing to keep the cabin dry and clean.
08
Propeller Replacement
Parts Replacement
2) Unscrew steering
gear and fixing screws
and then take out fixing
parts.
Disassembly
Installation
Replace the steering gear with powered on,please noted the propeller turns
unexpectedly.
Replac the steering gear
4) The steering gear
is separated from the
steering gear arm.
Arm of steering gear
Tie rod
When the new steering gear is powered on,the installation should be conducted in
the direction of disassembly sequence.
1) Unscrew tie rod assembly screws.
Turn off the power of boat
2) Steering gear
Steering gear 3) Unscrew the
steering gear arm
screws.
Propeller fastener
Propeller fastener
Anti-slip nuts
Installation:
Install the new propeller and tighten the
anti-skid nut clockwise after the notch
position fits the fastener.
Remove:
Disconnect the power of boat and hold the
propeller fasteners,Unscrew the anti-skid
nut counterclockwise to remove the propeller.
09
Troubleshooting Guide
Problem
The transmitter
indicator light
is off
Solution
The boat tilts
to one side
1) Make sure whether the propeller is damaged or replace a new one.
4) Make sure whether the motor is damaged or replace a new one.
1) Operate according to the “trimmer” as per instructions.
2) Calibrate the steering gear arm.
3) The steering gear is damaged, replace a new one.
Unable to
frequency
The boat is
under-powered
or can not go
forward
1) Replace the transmitter battery.
1) Operate the boat step by step in accordance with the user manual.
2) Make sure signal interference nearby and keep away.
3) The electronic component is damaged for frequent crash.
2) When the battery is low, charger it in time. Or replace it with a new battery.
3) Make sure install the propeller correctly.
2) Please make sure the battery is installed correctly.
4) Please make sure turn on the power.
3) Clean the dirt from metal contacts in battery groove.
Steel rope fasteners Steel rope
Noted: When the propeller is entangled with debris, the stell rope is easy to burst.Please be
sure to avoid debris in the water. The replacement of steel rope must be carried our
with the battery power cut off.
Installation: Replace the new steel rope, the installation step is opposite to the removal step.
Remove: Remove the propeller, unscrew the propeller fastener and steel rope fastener used a hex
wrench and then draw out the steel rope.
Replacement the Steel Rope
10
FCC Note
WARNING
Warning: The product should only be used by adults and children over 14 years.
Adult supervision is required for children under 14 years.
Hinweis: Dieses Produkt ist für die Erwachsene und die Kinder ab 14 Jahren.
Die kinder unter 14 Jahren müssen von Erwachsenen beaufsichtigt werden.
Avertissement: Ce produit est destiné aux adultes et aux enfants de plus de 14 ans.
Les enfants de moins de 14 ans doivent être surveillés par des adultes.
Avvertimento: Questo prodotto è destinato all'uso per i adulti e bambini di età superiore ai 14 anni.
I bambini di età inferiore ai 14 anni devono essere sorvegliati da un adulto.
Advertencia: Este producto es para adultos y niños mayores de 14 años.
Los niños menores de 14 años deben ser supervisados por adultos.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interferencein a residential
installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
Reorient or relocate the receiving a ntenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which thereceiver is connected.
WARNING: Changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.
DANGER!
Only suitable
for age 14+
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired operation.
The equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful
interference unless the modifications are expressly approved in the instruction manual. Modifications not authorized by the
manufacturer may void user’s authorityto operate this device.
The device has been evaluated to meet general RF exposure requirement.
The device can be used in portable exposure condition with out restriction.
FCC Radiation Exposure Statement
FCC Notice
11
Address: Guangfeng Industrial Zone, Guangyi Street, Chenghai District, Shantou City, Guangdong Province, CN
Manufacturer: SHANTOU CITY CHENGHAI UDIRC TOYS CO., LTD
Model: UDI021
MADE IN CHINA
12
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

udiR C UDI021 Remote Control Boat Guida utente

Marca
udiR C
Modello
UDI021 Remote Control Boat
Tipo
Guida utente
Scarica PDF
rapporto

in altre lingue

Documenti correlati

Altri documenti