Intel Life Jacket II Manuale utente

Intel

®

Astor II Server Chassis

Subassembly Product Guide

A Guide for Technically Qualified Assemblers of Intel

®

Identified Subassemblies/Products

Order Number: 722623-001

If an FCC declaration of conformity marking is present on the board, the following statement applies:

FCC Declaration of Conformity

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)

this device may not cause harmful interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

For questions related to the EMC performance of this product, contact:

Intel Corporation

5200 N.E. Elam Young Parkway

Hillsboro, OR 97124

1-800-628-8686

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause harmful interference to

radio communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the interference by

one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and the receiver.

Connect the equipment to an outlet on a circuit other than the one to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

Canadian Department of Communications Compliance Statement:

This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set

out in the Radio Interference Regulations of the Canadian Department of Communications.

Le présent appareil numerique német pas de bruits radioélectriques dépassant les limites applicables aux

appareils numériques de la classe B prescrites dans le Réglement sur le broullage radioélectrique édicté par

le ministére des Communications du Canada.

Disclaimer

Information in this document is provided in connection with Intel products. No license, express or implied, by

estoppel or otherwise, to any intellectual property rights is granted by this document. Except as provided in

Intel's Terms and Conditions of Sale for such products, Intel assumes no liability whatsoever, and Intel

disclaims any express or implied warranty, relating to sale and/or use of Intel products including liability or

warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright

or other intellectual property right. Intel products are not designed, intended or authorized for use in any

medical, life saving, or life sustaining applications or for any other application in which the failure of the Intel

product could create a situation where personal injury or death may occur. Intel may make changes to

specifications and product descriptions at any time, without notice.

The Astor II Chassis may contain design defects or errors known as errata which may cause the product to

deviate from published specifications. Current characterized errata are available on request. Copies of

documents which have an ordering number and are referenced in this document, or other Intel literature, may

be obtained from:

Intel Corporation

P.O. Box 5937

Denver, CO 80217-9808

or call in North America 1-800-548-4725, Europe 44-0-1793-431-155, France 44-0-1793-421-777,

Germany 44-0-1793-421-333, other Countries 708-296-9333.

†

Third party brands and names are property of their respective owners.

Copyright Intel Corporation 1998.

iii

Contents

1 System Description

Kit Contents.......................................................................................................................... 7

Feature Summary ................................................................................................................ 7

Chassis Front Controls and Indicators......................................................................... 8

Chassis Back I/O Ports and Features.......................................................................... 9

Chassis Side View......................................................................................................10

Peripherals..........................................................................................................................11

External Bay for 5.25-inch Removable Media Devices ...............................................11

Internal Bay for 3.5-inch IDE Hard Drives...................................................................11

Hot-swap Bay.............................................................................................................11

Power Supply......................................................................................................................12

Checking the Power Cord...........................................................................................12

System Cooling...................................................................................................................12

System Security..................................................................................................................13

Mechanical Locks.......................................................................................................13

Monitoring...................................................................................................................13

2 Working Inside the System

Tools and Supplies Needed ................................................................................................15

Safety: Before You Remove the Side Cover.......................................................................15

Warnings and Cautions.......................................................................................................15

Removing the Side Cover....................................................................................................16

Installing Chassis Feet........................................................................................................17

Removing the Hot-swap Bay...............................................................................................18

Removing the IDE Drive Bay...............................................................................................19

Installing Server Board Clips and Bumpers.........................................................................21

I/O Shield............................................................................................................................22

Installing the Server Board..................................................................................................22

Installing a Chassis Intrusion Switch ...................................................................................24

Removing the Front Cover ..................................................................................................25

Installing the Diskette Drive.................................................................................................26

Removing the Diskette Drive...............................................................................................26

Hard Drives.........................................................................................................................27

Drive Cabling Considerations .....................................................................................27

Installing a Hard Drive into the IDE Drive Bay.............................................................27

Removing a Hard Drive from the IDE Drive Bay.........................................................28

Installing the IDE drive bay.........................................................................................29

Installing a 5.25-inch Peripheral Device......................................................................30

Removing a 5.25-inch Peripheral Device....................................................................32

Installing the Front Cover....................................................................................................33

Installing the Hot-swap Bay.................................................................................................33

Installing an Add-in Board ...................................................................................................33

Removing an Add-in Board .................................................................................................34

iv Intel Astor II Server Chassis Subassembly Product Guide

Installing the Side Cover......................................................................................................35

Hot-swap Bay......................................................................................................................36

SCSI Hard Disk Drives ...............................................................................................36

Mounting a SCSI SCA2 Hard Disk Drive in a Plastic Carrier.......................................36

Installing a SCSI SCA2 Hard Disk Drive in the Hot-swap Bay ....................................37

Hot-swapping a SCSI SCA2 Hard Disk Drive .............................................................38

Fans ...................................................................................................................................39

Removing the Front Fan.............................................................................................39

Installing the Front Fan...............................................................................................40

Removing a Hot-swap Bay Fan..................................................................................41

Installing a Hot-swap Bay Fan....................................................................................41

Hot-swap Backplane ...........................................................................................................42

Removing the SCSI Backplane...................................................................................42

Installing the SCSI Backplane.....................................................................................43

Front Panel Board...............................................................................................................44

Removing the Front Panel Board................................................................................44

Installing the Front Panel Board..................................................................................44

3 Technical Reference

Power Supply Specifications...............................................................................................45

Input Voltages.............................................................................................................45

Output Voltages..........................................................................................................45

Environmental Specifications ..............................................................................................46

SCSI Hot-swap Backplane Connectors...............................................................................47

Ultra2/LVD SCSI 16-Bit Connector.............................................................................47

Ultra2/LVD SCA2 SCSI 16-Bit Connectors.................................................................48

Power Connectors......................................................................................................49

Backplane Fan Connector ..........................................................................................49

Front Panel Cable Connector .....................................................................................50

4 Regulatory Information

Regulatory Compliance.......................................................................................................51

Safety Compliance......................................................................................................51

EMC Compliance........................................................................................................52

Regulatory Compliance Markings...............................................................................53

Electromagnetic Compatibility Notice (USA)........................................................................53

FCC Declaration of Conformity...................................................................................54

Electromagnetic Compatibility Notices (International)..........................................................54

Installation Safety Instructions....................................................................................55

Use Only for Intended Applications.............................................................................56

A Equipment Log and Worksheets

Equipment Log....................................................................................................................57

Current Usage.....................................................................................................................59

Calculating Power Usage............................................................................................59

Contents v

B Warnings

WARNING: English (US)....................................................................................................62

AVERTISSEMENT: Français..............................................................................................64

WARNUNG: Deutsch.........................................................................................................66

AVVERTENZA: Italiano......................................................................................................68

ADVERTENCIAS: Español.................................................................................................70

C Warranty

Limited Warranty for Intel

®

Server Chassis Subassembly Products....................................73

Extent of Limited Warranty..................................................................................................73

Warranty Limitations and Exclusions...................................................................................74

Limitations of Liability..................................................................................................74

How to Obtain Warranty Service.........................................................................................75

Telephone Support.....................................................................................................75

Returning a Defective Product....................................................................................76

Figures

1. Front Controls and Indicators ...................................................................................... 8

2. Back I/O Ports and Features ....................................................................................... 9

3. Chassis Side View......................................................................................................10

4. System Security .........................................................................................................13

5. Removing the Side Cover...........................................................................................17

6. Removing the Hot-swap Bay......................................................................................18

7. Disconnect Cables and Remove Screws....................................................................19

8. IDE Hard Drive Bay....................................................................................................20

9. Rubber Bumper and Standoff Clip Placement ............................................................21

10. Installing the I/O Shield (typical shield shown)............................................................22

11. Installing the Server Board (typical board shown).......................................................23

12. Installing a Chassis Intrusion Switch...........................................................................24

13. Removing the Front Cover..........................................................................................25

14. Installing the Diskette Drive........................................................................................26

15. IDE Cable Dimensions................................................................................................27

16. IDE Hard Drive...........................................................................................................28

17. Disconnect Cables and Remove Screws....................................................................29

18. Remove Filler Panels and EMI Shields.......................................................................30

19. Snap-in Plastic Slide Rails..........................................................................................31

20. Installing a Removable Media Device.........................................................................32

21. Installing an Add-in Board...........................................................................................34

22. Hard Disk Drive and Plastic Carrier............................................................................37

23. Installing a Hard Disk Drive ........................................................................................38

24. Removing the Fan Bracket.........................................................................................39

25. Installing the Front Fan...............................................................................................40

26. Removing the Hot-swap Bay Fan Bracket..................................................................41

27. Removing the Plastic Shroud .....................................................................................42

28. Removing the SCSI Backplane...................................................................................43

29. Removing the Front Panel Board................................................................................44

vi Intel Astor II Server Chassis Subassembly Product Guide

Tables

1. Feature Summary........................................................................................................ 7

2. Fan Cable Connector Pinout ......................................................................................39

3. Power Supply Output Voltages...................................................................................45

4. Environmental Specifications......................................................................................46

5. Wide/Fast SCSI 16-Bit Connector Pinout ...................................................................47

6. Wide/Fast SCA2 SCSI 16-Bit Connector Pinout.........................................................48

7. Power Connector Pinout.............................................................................................49

8. Backplane Fan Connector Pinout...............................................................................49

9. Front Panel Connector Pinout ....................................................................................50

10. Power Usage Worksheet 1.........................................................................................59

11. Power Usage Worksheet 2.........................................................................................60

7

1 System Description

Kit Contents

The Astor II chassis subassembly kit includes this Product Guide, a power cord, an I/O shield EMI

gasket, two chassis feet, and three hardware bags:

Server board installation bag: includes three rubber bumpers, 13 standoff clips, and 13

retention screws.

Chassis intrusion switch bag: includes one intrusion switch/cable assembly, one mounting

screw, and three wire tie clips.

Internal/external peripheral mounting bag: includes four 5.25-inch external drive rails and

mounting screws without washers (2 screws/rail x 4 + 2 for diskette = 10 total); mounting

screws with washers for SCA2 hard drive caddies (4 screws/drive x 5 + 1 spare = 21 total);

mounting screws with washers for chassis feet (2 screw/foot x 2 = 4 total); and gold colored

mounting screws for IDE drives (4 screws/drive x 2 = 8 total).

Feature Summary

Table 1. Feature Summary

Feature Description

Drive Bays One 3.5-inch diskette drive bay, accessible from front.

Two 5.25-inch wide bays that are externally accessible, designed to hold half-

height standard removable media devices; the bays can be converted into a

single full-height bay.

Hot-swap bay for 3.5-inch hard disk drives: space for up to five 1-inch high,

SCA2 hard drives.

Two 3.5-inch wide bays that are not externally accessible, designed to hold

half-height IDE drives.

Expansion slot covers Up to seven expansion slots can be used; every slot that does not have an

add-in board installed must have a slot cover installed.

Power supply 300 watt power factor correction (PFC) power supply, integrated cooling fan.

Detachable AC power cord.

Cooling Three system fans inside the chassis and one power supply fan provide

cooling and airflow.

8 Intel Astor II Server Chassis Subassembly Product Guide

Chassis Front Controls and Indicators

OM07034

A

B

J

I

G

H

K

C

D

E

F

Figure 1. Front Controls and Indicators

A. Empty 5.25-inch drive bay

B. CD-ROM drive*

C. Power LED

D. Hard disk access LED

E. Network LED

F. Fan fault LED

G. Power button

H. Reset button

I. Hot-swap drive failure LEDs

J. Hot-swap drive bay

K. Diskette drive*

* Items shown may not be included in the chassis.

System Description 9

Chassis Back I/O Ports and Features

OM07038

F G

H

I

J

E

A

B

C

D

Figure 2. Back I/O Ports and Features

A. Mouse and keyboard connectors*

B. Serial port A, COM1*

C. VGA monitor connector*

D. Network connector port*

E. Parallel port*

F. Power supply fan

G. AC input power connector

H. Side cover grip handle

I. Loop for padlock (padlock not supplied, see page 13

for padlock size)

J. Seven slot covers

* Typical baseboard I/O connectors shown.

10 Intel Astor II Server Chassis Subassembly Product Guide

Chassis Side View

OM07563

J

I

H

D

B

C

E

A

G F

L

K

Figure 3. Chassis Side View

A. CD-ROM drive*

B. 5.25-inch external bays

C. 3.5-inch diskette drive*

D. Hot-swap drive bay

E. Fan housing

F. Card guide

G. Hot-swap fan shroud with two fans

H. Add-in board expansion slot covers

I. Security lock

J. Server board

K. Power supply

L. 3.5-inch IDE drive bay

* Items shown may not be included in the chassis.

System Description 11

Peripherals

External Bay for 5.25-inch Removable Media Devices

The chassis has a bay for two 5.25-inch half-height peripherals that is accessible from the front of

the system. This bay is intended to provide space for CD-ROM, tape backup or other removable

devices.

You can convert the 5.25-inch bays to a single full-height bay. We recommend that you do not use

this bay for hard disk drives, because they generate EMI, ESD susceptibility increases, and the

drive will not be adequately cooled.

Internal Bay for 3.5-inch IDE Hard Drives

The chassis has a 3.5-inch bay for two half-height or 1-inch high IDE hard drives. The bay is not

externally accessible.

Hot-swap Bay

A hot-swap bay is provided for five SCSI SCA2 hard drives that are 3.5 inches wide and 1 inch

high. The bay is designed for drives that consume up to 17 watts of power each. Drives must be

specified to run at a maximum ambient temperature of 50 C.

The system was designed to allow the user to install a Redundant Array of Independent Disks

(RAID). A software implementation with onboard SCSI or an add-in RAID controller card can be

used to set up RAID applications.

SCSI Hot-swap Backplane

The hot-swap backplane provides the following:

Five Single Connector Assembly (SCA2) connectors for SCA2-compatible SCSI drives

Power control for each drive, including automatic slot-power-down upon removing a drive

Signal for a fault indicator on the front panel for each drive

Internal IMB (Intelligent Management Bus)

Two +12 V connectors for a fan with tachometer

Local IMB-based temperature sensor

The SCSI hot-swap backplane provides control signals and power for five Ultra2/LVD 3.5-inch,

1-inch high, SCA2 SCSI hard disk drives. The backplane receives control signals from the SCSI

controller on the server board through a cable connected to the wide SCSI connector on the

backplane. The backplane is powered through cables connected to the two power connectors.

The drives get their control signals and power from the SCA2 connectors on the backplane.

The fault indicators on the front panel indicate failure status for each drive in the bay. These

indicators get their signals through a cable connected to the front panel connector on the

backplane.

12 Intel Astor II Server Chassis Subassembly Product Guide

The temperature sensor on the backplane provides temperature information to the BMC (baseboard

management controller) on the server board through chassis service messages.

The backplane power control will power down a drive when a failure is detected and reported to

the SCSI bus. When a new drive is inserted, the power control waits a short time for the drive to

become fully seated and then applies power to the drive.

Power Supply

The 300 watt PFC (power factor correction) universal type power supply is designed to minimize

EMI. The supply operates within the following voltage ranges and is rated as follows:

100-120 V at 50/60 Hertz (Hz); 4.6 A maximum

200-240 V at 50/60 Hz; 2.3 A maximum

The DC output voltages of the power supply are +5 V, +12 V, +3.3 V, -5 V, -12 V, and

+5 V standby. Power to the server board is provided through the power cable to the 24-pin main

power connector.

Checking the Power Cord

WARNING

Do not attempt to modify or use a supplied AC power cord if it is not the

exact type required.

If a power cord supplied with the system is not compatible with the AC wall outlet in your region,

get one that meets the following criteria:

The cord must be rated for the available AC voltage and have a current rating that is at least

125% of the current rating of the system.

The connector that plugs into the wall outlet must be a grounding-type male plug designed

for use in your region. It must have certification marks showing certification by an agency

acceptable in your region.

The connector that plugs into the AC receptacle on the system power supply must be an IEC

320, sheet C13, type female connector.

In Europe, the cord must be less than 4.5 meters (14.76 feet) long, and it must be flexible

<HAR> (harmonized) or VDE certified cordage to comply with the system's safety

certifications.

System Cooling

The chassis includes four tachometer fans for cooling and airflow. One of these is the integrated

fan in the power supply.

✏

NOTE

The chassis side cover must be on the system for proper cooling.

System Description 13

System Security

To help prevent unauthorized entry or use of the system, the chassis includes a chassis intrusion

switch that can be monitored by Server Management software and two padlock loops.

Mechanical Locks

A padlock loop on the rear of the system side cover can be used to prevent access to the

microprocessors, memory, and add-in cards. A variety of lock sizes can be accommodated by the

.300 diameter loop.

A padlock loop on the hard drive bay EMI door provides security for the hot swap hard drives.

The allotted space accommodates a MasterLock

†

model 120-D or equivalent lock. Dimensions:

.815” H x .830” W x .430” D. Pall diameter .145”

Monitoring

Install the chassis intrusion switch. When the side cover is removed, the switch transmits a signal

to the BMC on the server board. Server management software can be programmed to respond to

an intrusion by powering down or by locking the keyboard, for example.

OM07044

Figure 4. System Security

14 Intel Astor II Server Chassis Subassembly Product Guide

15

2 Working Inside the System

Tools and Supplies Needed

Phillips (cross head) screwdriver (#2 bit)

Antistatic wrist strap (recommended)

Needle-nosed pliers

Safety: Before You Remove the Side Cover

Before removing the system side cover for any reason, observe these safety guidelines.

1. Turn off all peripheral devices connected to the system.

2. Turn off the system by pressing the power button on the front of the system. Then unplug the

AC power cord from the system or wall outlet.

3. Label and disconnect all peripheral cables and all telecommunication lines connected to I/O

connectors or ports on the back of the system.

4. Provide some electrostatic discharge (ESD) protection by wearing an antistatic wrist strap

attached to chassis ground of the system—any unpainted metal surface—when handling

components.

Warnings and Cautions

These warnings and cautions apply whenever you remove the side cover of the system to access

components inside the system. Only a technically qualified person should integrate and configure

the system.

WARNINGS

The power button (a convex button) on the front panel DOES NOT turn

off the system AC power. To remove power from system, you must

unplug the AC power cord from the wall outlet or the system.

Hazardous electrical conditions may be present on power, telephone,

and communication cables. Turn off the system and disconnect the

power cords, telecommunications systems, networks, and modems

attached to the system before opening it. Otherwise, personal injury or

equipment damage can result.

Hazardous voltage, current, and energy levels are present inside the

power supply. There are no user-serviceable parts inside it; servicing

should be done by technically qualified personnel.

16 Intel Astor II Server Chassis Subassembly Product Guide

CAUTIONS

ESD can damage disk drives, boards, and other parts. Perform all

procedures in this chapter only at an ESD workstation. If one is not

available, provide some ESD protection by wearing an antistatic wrist strap

attached to chassis ground any unpainted metal surface on your system

when handling parts.

Always handle boards carefully. They can be extremely sensitive to ESD.

Hold boards only by their edges. Do not touch the connector contacts. After

removing a board from its protective wrapper or from the system, place the

board component side up on a grounded, static free surface. If you place the

server board on a conductive surface, the battery leads may short out. If

they do, this will result in a loss of CMOS data and will drain the battery.

Use a conductive foam pad if available but not the board wrapper. Do not

slide board over any surface.

For proper cooling and airflow, always install the chassis side cover before

turning on the system. Operating it without the cover in place can damage

system parts.

Removing the Side Cover

You need to remove the chassis side cover, and in some cases the front cover, to gain access to

components inside the system.

1. Observe the safety and ESD precautions at the beginning of this chapter.

2. Turn off all peripheral devices connected to the system.

3. Turn off the system by pressing the power button on the front panel, AND unplugging the AC

power cord.

4. Label and disconnect all peripheral cables attached to the I/O panel on the back of the system.

5. Remove and save the three screws from the side cover; you will need them later to reattach the

cover.

6. Place the fingertips of your left hand under the built in handle on the back of the cover.

7. Using an even pull, slide the cover backward, about an inch, until it stops.

8. Using your left hand, pull the back end of the cover toward you to disengage its bottom row of

tabs from the notches in the chassis.

9. Using both hands, lift the cover upward to disengage the top row of tabs from the notches in

the top edge of the chassis. Set the cover aside.

Working Inside the System 17

OM06410

A

C

B

Figure 5. Removing the Side Cover

A. Built in handle

B. Metal loop (for padlock)

C. Retaining screws (3)

Installing Chassis Feet

1. Each chassis foot has two sets of holes. The larger holes fit over alignment features in the

chassis to assist positioning the feet.

2. Align the smaller holes with the corresponding screw holes on the chassis bottom, and attach

each foot with two screws (silver screws with washers are provided).

18 Intel Astor II Server Chassis Subassembly Product Guide

Removing the Hot-swap Bay

✏

NOTE

The hot-swap bay may be heavy if it is full of drives. It is not necessary to

remove the drives from the bay before removing the bay from the chassis.

However, we recommend you remove any drives in the bay before removing

the bay to minimize the risk of personal injury or property damage.

1. Remove the side cover. You do not need to remove the plastic front cover.

2. Remove the three screws holding the bay chassis.

3. Disconnect the power and data cables from the SCSI backplane.

4. Pivot the bay until it comes out of the chassis.

OM07043

A

Figure 6. Removing the Hot-swap Bay

A. Pivot point

Working Inside the System 19

Removing the IDE Drive Bay

1. Observe the safety and ESD precautions at the beginning of this chapter.

2. Remove the side cover.

3. Disconnect the power and signal cables from any drives in the bay.

4. Remove and save the two screws at the top of the bay.

OM07560

A

B

C

Figure 7. Disconnect Cables and Remove Screws

A. Power cable

B. Data cable

C. Screws

5. Remove and save the screw in the flange at the bottom of the drive bay (see Figure 8, A).

6. Push the drive bay up and pull it out of the chassis. Do not swing it on its hinges, as the flange

may get caught in the fans mounted on the hot-swap bay.

20 Intel Astor II Server Chassis Subassembly Product Guide

OM07561

A

Figure 8. IDE Hard Drive Bay

A. Screw

La pagina sta caricando ...

Intel Life Jacket II Manuale utente

Questo manuale è adatto anche per

Intel Life Jacket II Manuale utente

in altre lingue

Documenti correlati

Altri documenti