Planet UL9200N Manuale utente

Categoria
Router
Tipo
Manuale utente

Questo manuale è adatto anche per

I
I
Copyright
Copyright 2017 by PLANET Technology Corp. All rights reserved. No part of this publication may be
reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or
computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical,
manual or otherwise, without the prior written permission of PLANET.
PLANET makes no representations or warranties, either expressed or implied, with respect to the
contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular
purpose. Any software described in this manual is sold or licensed "as is". Should the programs
prove defective following their purchase, the buyer (and not this company, its distributor, or its dealer)
assumes the entire cost of all necessary servicing, repair, and any incidental or consequential
damages resulting from any defect in the software. Further, this company reserves the right to revise
this publication and to make changes from time to time in the contents hereof without obligation to
notify any person of such revision or changes.
All brand and product names mentioned in this manual are trademarks and/or registered trademarks of
their respective holders.
FCC Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution:
Any changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment. This transmitter must not be co-located or operating
in conjunction with any other antenna or transmitter. To assure continued compliance, for example, use
only shielded interface cables when connecting to computer or peripheral devices.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference
(2) This device must accept any interference received, including interference that may cause undesired
operation.
II
This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with a minimum distance of 21cm between the
radiator and your body.
CE Compliance Statement
This device meets the RED directive 2014/53/EU of EU requirements on the limitation of exposure of
the general public to electromagnetic fields by way of health protection.
The device complies with RF
specifications in that the distance between the device and your body should not be less than 20 cm.
Safety
This equipment is designed with the utmost care for the safety of those who install and use it. However,
special attention must be paid to the dangers of electric shock and static electricity when working with
electrical equipment. All guidelines must be followed at all times to ensure the safe use of the
equipment.
WEEE regulation
To avoid the potential effects on the environment and human health as a result of the presence of
hazardous substances in electrical and electronic equipment, end users of electrical and
electronic equipment should understand the meaning of the crossed-out wheeled bin
symbol. Do not dispose of WEEE as unsorted municipal waste; WEEE should be collected
separately.
Revision
User Manual of PLANET 2.4GHz 300Mbps 802.11n Outdoor Wireless AP/CPE
Model: WAP-200N/WBS-200N
Rev: 1.0 (August, 2017)
Part No. EM-WAP-200N_WBS-200N_v1.0
III
CONTENTS
Chapter 1. Product Introduction ........................................................................................................... 7
1.1 Package Contents ............................................................................................................... 7
1.2 Product Description ............................................................................................................ 8
1.3 Product Features ............................................................................................................... 10
1.4 Product Specifications ..................................................................................................... 11
Chapter 2. Hardware Installation ........................................................................................................ 14
2.1 Hardware Description ....................................................................................................... 14
2.1.1 The Bottom Panel ................................................................................................... 16
Chapter 3. Connecting to the AP ........................................................................................................ 18
3.1 Preparation before Installation ........................................................................................ 18
3.1.1 Professional Installation Required .......................................................................... 18
3.1.2 Safety Precautions .................................................................................................. 18
3.2 Installation Precautions .................................................................................................... 18
3.3 Installing the AP ................................................................................................................ 20
Chapter 4. Quick Installation Guide ................................................................................................... 22
4.1 Manual Network Setup -- TCP/IP Configuration ............................................................. 22
4.1.1 Configuring the IP Address Manually ..................................................................... 22
4.2 Starting Setup in the Web UI ............................................................................................ 25
Chapter 5. Configuring the AP ............................................................................................................ 27
5.1 Operation Mode ................................................................................................................. 27
5.1.1 Access Point (AP) ................................................................................................... 29
5.1.2 Client Bridge (CB) ................................................................................................... 30
5.1.3 WDS Access Point (WDS AP) ................................................................................ 31
5.1.4 WDS Station (WDS STA) ........................................................................................ 32
5.1.5 WDS Bridge (WDS PtP/WDS PtMP) ...................................................................... 33
5.1.6 Client Router (CR/WISP) ........................................................................................ 39
5.1.7 Repeater ................................................................................................................. 45
5.2 Status.................................................................................................................................. 49
5.2.1 Main ........................................................................................................................ 49
5.2.2 Save/Reload ........................................................................................................... 51
5.2.3 Wireless Client List ................................................................................................. 52
5.2.4 WDS Link List ......................................................................................................... 53
5.2.5 DHCP Client Table .................................................................................................. 53
5.2.6 Connection Status ................................................................................................... 54
5.2.7 System Log ............................................................................................................. 55
5.3 System ................................................................................................................................ 56
5.3.1 IP Settings ............................................................................................................... 56
IV
5.3.2 Spanning Tree Settings (STP) ................................................................................ 57
5.4 Router (WISP Mode Only) ................................................................................................. 58
5.4.1 DHCP Server Settings ............................................................................................ 58
5.4.2 WAN Settings .......................................................................................................... 59
5.4.2.1. DHCP ............................................................................................................................. 60
5.4.2.2. Static IP .......................................................................................................................... 61
5.4.2.3. PPPoE ........................................................................................................................... 63
5.4.2.4. PPTP ............................................................................................................................. 64
5.4.3 VPN Pass Through ................................................................................................. 65
5.4.4 Port Forwarding ...................................................................................................... 66
5.4.5 DMZ Settings .......................................................................................................... 67
5.5 Wireless .............................................................................................................................. 68
5.5.1 Wireless Network .................................................................................................... 68
5.5.2 WDS Link Settings .................................................................................................. 71
5.5.3 Security Settings ..................................................................................................... 73
5.5.4 Wireless MAC Filter ................................................................................................ 83
5.5.5 Wireless Advanced Settings ................................................................................... 84
5.6 Management ...................................................................................................................... 85
5.6.1 Administration (Password Settings) ........................................................................ 85
5.6.2 Management VLAN ................................................................................................ 86
5.6.3 SNMP Settings ....................................................................................................... 87
5.6.4 Backup/Restore Settings ........................................................................................ 88
5.6.5 Auto Reboot Settings .............................................................................................. 89
5.6.6 Firmware Upgrade .................................................................................................. 89
5.6.7 Time Settings .......................................................................................................... 91
5.6.8 Wi-Fi Schedule ....................................................................................................... 92
5.6.9 CLI Settings ............................................................................................................ 93
5.6.10 Log .......................................................................................................................... 93
5.6.11 Diagnostics ............................................................................................................. 94
5.6.12 Logout ..................................................................................................................... 95
Appendix A: Troubleshooting ............................................................................................................ 96
Appendix B: Use Planet Smart Discovery to find AP ...................................................................... 98
Appendix C: FAQ ................................................................................................................................. 99
Q1: How to set up the AP Client Connection ........................................................................... 99
Q2: How to set up the WDS Connection ................................................................................ 108
V
FIGURES
FIGURE 2-1 THREE-WAY VIEW (WAP-200N) ........................................................................................................ 14
FIGURE 2-2 THREE-WAY VIEW (WBS-200N) ........................................................................................................ 14
FIGURE 2-3 REAR PANEL (WAP-200N) ................................................................................................................ 15
FIGURE 2-4 REAR PANEL (WBS-200N) ................................................................................................................ 15
FIGURE 2-5 BOTTOM PANEL (WAP-200N/WBS-200N) ........................................................................................ 17
FIGURE 2-6 POE WARNING LABEL ....................................................................................................................... 17
FIGURE 3-1 POE AND LAN PORT CONNECTION ..................................................................................................... 20
FIGURE 3-2 FINISH INSTALLATION AND CONNECT TO ANTENNAS (WAP-200N ONLY) ........................................... 20
FIGURE 3-3 POLE MOUNTING ............................................................................................................................... 21
FIGURE 3-4 WALL MOUNTING .............................................................................................................................. 21
FIGURE 4-1 TCP/IP SETTING ................................................................................................................................ 23
FIGURE 4-2 WINDOWS START MENU .................................................................................................................... 24
FIGURE 4-3 SUCCESSFUL RESULT OF PING COMMAND .......................................................................................... 24
FIGURE 4-4 FAILED RESULT OF PING COMMAND ................................................................................................... 25
FIGURE 4-5 LOGIN BY DEFAULT IP ADDRESS ......................................................................................................... 25
FIGURE 4-6 LOGIN WINDOW ................................................................................................................................ 25
FIGURE 4-7 WEB UI SCREENSHOT ........................................................................................................................ 26
FIGURE 5-1 OPERATION MODE ALL ................................................................................................................... 28
FIGURE 5-2 OPERATION MODE AP ..................................................................................................................... 29
FIGURE 5-3 OPERATION MODE CLIENT BRIDGE ................................................................................................. 30
FIGURE 5-4 OPERATION MODE WDS AP ........................................................................................................... 31
FIGURE 5-5 OPERATION MODE WDS STATION ................................................................................................... 32
FIGURE 5-6 OPERATION MODE WDS BRIDGE .................................................................................................... 33
FIGURE 5-7 OPERATION MODE CLIENT ROUTER (WISP) ................................................................................... 39
FIGURE 5-8 OPERATION MODE REPEATER ......................................................................................................... 45
FIGURE 5-9 SYSTEM MENU - RESET ..................................................................................................................... 49
FIGURE 5-10 SYSTEM MENU LANGUAGE OPTION .............................................................................................. 49
FIGURE 5-11 MAIN STATUS ................................................................................................................................... 50
FIGURE 5-12 SAVE/RELOAD ................................................................................................................................. 51
FIGURE 5-13 SAVE/RELOAD - DEFAULT ................................................................................................................ 52
FIGURE 5-14 WIRELESS CLIENT LIST ................................................................................................................... 52
FIGURE 5-15 KICK THE CLIENT ............................................................................................................................. 52
FIGURE 5-16 WDS LINK STATUS .......................................................................................................................... 53
FIGURE 5-17 DHCP CLIENT LIST ......................................................................................................................... 53
FIGURE 5-18 CONNECTION STATUS ...................................................................................................................... 54
FIGURE 5-19 SYSTEM LOG ................................................................................................................................... 55
FIGURE 5-20 LAN IP SETTINGS ............................................................................................................................ 56
FIGURE 5-21 SPANNING TREE SETTINGS ............................................................................................................... 57
FIGURE 5-22 DHCP SERVER SETTINGS ................................................................................................................ 58
FIGURE 5-23 WAN SETTINGS ALL ..................................................................................................................... 59
FIGURE 5-24 WAN SETTINGS DHCP ................................................................................................................. 61
FIGURE 5-25 WAN SETTINGS STATIC IP ............................................................................................................ 62
VI
FIGURE 5-26 WAN SETTINGS PPPOE ................................................................................................................ 63
FIGURE 5-27 WAN SETTINGS PPTP .................................................................................................................. 64
FIGURE 5-28 VPN PASS THROUGH ....................................................................................................................... 65
FIGURE 5-29 PORT FORWARDING .......................................................................................................................... 66
FIGURE 5-30 PORT FORWARDING .......................................................................................................................... 67
FIGURE 5-31 DMZ ............................................................................................................................................... 68
FIGURE 5-32 WIRELESS NETWORK AP/WDS AP MODE .................................................................................... 69
FIGURE 5-33 WIRELESS NETWORK SSID PROFILE............................................................................................. 69
FIGURE 5-34 WIRELESS NETWORK CB/WDS STA/CR/REPEATER MODE ......................................................... 71
FIGURE 5-35 WDS LINK SETTINGS WDS BRIDGE MODE .................................................................................. 72
FIGURE 5-36 SECURITY SETTINGS AP/WDS AP MODE ..................................................................................... 73
FIGURE 5-37 SECURITY SETTINGS CB/WDS STA/CR/REPEATER MODE ........................................................... 73
FIGURE 5-38 SECURITY SETTINGS WDS BRIDGE MODE .................................................................................... 74
FIGURE 5-39 SECURITY SETTINGS WEP ............................................................................................................ 75
FIGURE 5-40 SECURITY SETTINGS WPA-PSK .................................................................................................... 76
FIGURE 5-41 SECURITY SETTINGS WPA2-PSK .................................................................................................. 77
FIGURE 5-42 SECURITY SETTINGS WPA-PSK MIXED ........................................................................................ 77
FIGURE 5-43 SECURITY SETTINGS WPA (WPA ENTERPRISE) ............................................................................. 78
FIGURE 5-44 SECURITY SETTINGS WPA2 (WPA2 ENTERPRISE) ........................................................................ 79
FIGURE 5-45 SECURITY SETTINGS WPA MIXED (WPA MIXED ENTERPRISE) ..................................................... 81
FIGURE 5-46 WIRELESS MAC FILTER .................................................................................................................. 83
FIGURE 5-47 WIRELESS ADVANCED SETTINGS ..................................................................................................... 84
FIGURE 5-48 ADMINISTRATION (PASSWORD SETTINGS) ........................................................................................ 86
FIGURE 5-49 MANAGEMENT VLAN ..................................................................................................................... 86
FIGURE 5-50 SNMP SETTINGS ............................................................................................................................. 87
FIGURE 5-51 BACKUP/RESTORE SETTINGS ........................................................................................................... 88
FIGURE 5-52 AUTO REBOOT SETTINGS ................................................................................................................. 89
FIGURE 5-53 FIRMWARE UPGRADE ....................................................................................................................... 89
FIGURE 5-54 TIME SETTINGS ................................................................................................................................ 91
FIGURE 5-55 WI-FI SCHEDULE ............................................................................................................................. 92
FIGURE 5-56 CLI SETTINGS .................................................................................................................................. 93
FIGURE 5-57 LOG ................................................................................................................................................. 93
FIGURE 5-58 DIAGNOSTICS................................................................................................................................... 94
FIGURE 5-59 LOGOUT ........................................................................................................................................... 95
User Manual of WAP-200N/WBS-200N
-7-
Chapter 1. Product Introduction
1.1 Package Contents
Thank you for choosing PLANET WAP-200N/WBS-200N series. Before installing the AP/CPE, please verify the
contents inside the package box.
WBS-200N / WAP-200N Quick Installation Guide Mounting Strap x 2
Screw Set x 1 PoE Injector & Power Cord Antenna x 2 (WAP-200N only)
If there is any item missing or damaged, please contact the seller
immediately.
User Manual of WAP-200N/WBS-200N
-8-
1.2 Product Description
Cost-effective Wireless Solution with Superior Performance
PLANET WAP-200N/WBS-200N 300Mbps 802.11n Outdoor Wireless AP/CPE offers a better range and
excellent throughput. Via the WAP-200N's RP-SMA antenna connectors and the WBS-200N's embedded 8dBi
dual-polarity directional antenna, it is easy to build different point to multi-point applications with good diversity
coverage and better noise immunity effect, thus heightening the performance and stability of a long-distance
connectivity.
Designed for Various Requirements
The WAP-200N/WBS-200N is dedicatedly designed for WISP solution that provides CPE users with Internet
access via the WISP provider in rural areas. Besides, it caters to various wireless communication connectivities
(AP, Client, WDS, Repeater and WISP), thus meeting users’ application requirements.
User Manual of WAP-200N/WBS-200N
-9-
Multiple SSIDs with VLAN Tagging
Multiple SSIDs can broadcast up to four wireless networks with different names. For management purposes, the
IEEE 802.1Q VLAN supported allows multiple VLAN tags to be mapped to multiple SSIDs to distinguish the
wireless access. This makes it possible for the WAP-200N/WBS-200N to work with managed Ethernet switches
to have VLANs assigned for a different access level and authority.
Flexible and Reliable Outdoor Characteristics
The WAP-200N/WBS-200N is definitely suitable for wireless IP surveillance to enable to have wide deployments
between buildings and to act as the backbone of public service. Additionally, its self-healing capability keeps
connection alive all the time. With the IP55-rated outdoor UV-resistant enclosure, the WAP-200N/WBS-200N
can perform normally under rigorous weather conditions, meaning it can be installed in any harsh, outdoor
environments. With the proprietary Power over Ethernet (PoE) design, the WAP-200N/WBS-200N can be
easily installed in the areas where power outlets are not available.
Advanced Security and Rigorous Authentication
The WAP-200N/WBS-200N supports 152-bit WEP, WPA/WPA2, WPA-PSK and WPA2-PSK wireless encryptions,
the advanced WPA2-AES mechanism and 802.1X RADIUS authentication, which can effectively prevent
eavesdropping by unauthorized users or bandwidth occupied by unauthenticated wireless access. Furthermore,
any users are granted or denied access to the wireless LAN network based on the ACL (Access Control List)
that the administrator pre-established.
Easy Deployment and Management
With user-friendly Web UI and comprehensive management features including client limit control and wireless
traffic shaping, the WAP-200N/WBS-200N is easy to limit the client access and inbound/outbound bandwidth
control, even for users who have no experience in setting up a wireless network. Furthermore, with the Planet
Smart Discovery Utility, SNMP and diagnostics tools, the WAP-200N/WBS-200N is convenient to be managed
remotely.
User Manual of WAP-200N/WBS-200N
-10-
1.3 Product Features
Industrial Compliant Wireless LAN
Compliant with the IEEE 802.11b/g/n wireless technology
2T2R architecture with data rate of up to 300Mbps
Equipped with two 10/100Mbps RJ45 ports, with auto MDI/MDI-X supported
Fixed Network Broadband Router
Supported WAN connection types in WISP mode: DHCP, Static IP, PPPoE, PPTP
Supports Port Forwarding and DMZ for various networking applications
Supports DHCP server in WISP mode
RF Interface Characteristics
Built-in 5dBi detachable antennas with RP-SMA connectors (WAP-200N)
Built-in 8dBi dual-polarization antenna (WBS-200N)
High output power with multiply-adjustable transmit power control
Outdoor Environmental Characteristics
IP55 rating
Passive Power over Ethernet design
Operating temperature: -20~70°C
Multiple Operation Modes and Wireless Features
Multiple operation modes: AP, Client Bridge, Client Router (WISP), WDS, Repeater
WMM (Wi-Fi multimedia) provides higher priority to multimedia transmitting over wireless
Wireless Traffic Shaping to control the upload/download bandwidth
Wi-Fi scheduler allows to be enabled or disabled based on predefined schedule
Secure Network Connection
Full encryption supported: 64-/128-/152-bit WEP, WPA/WPA2, WPA-PSK/WPA2-PSK and 802.1X
RADIUS authentication
Supports 802.1Q VLAN pass-through over WDS and SSID-to-VLAN mapping
Supports up to 50 entries of MAC address filtering
Easy Installation and Management
IPv4/IPv6 dual-stack management networks
Multilingual Web User Interface: English, Spanish, French, German, Portuguese, Russian, and
Simplified Chinese
CLI command and SNMP-based management interface
Self-healing mechanism through system auto reboot setting
System status monitoring through remote Syslog Server and Device Discovery
Diagnostic tools include Ping, Traceroute, Speed
Planet Smart Discovery Utility allows administrator to discover and locate each AP
User Manual of WAP-200N/WBS-200N
-11-
1.4 Product Specifications
Product
WAP-200N
WBS-200N
2.4GHz 300Mbps 802.11n Outdoor Wireless AP/CPE
Hardware Features
Standard Support
IEEE802.11b/g/n
IEEE 802.3
IEEE 802.3u
IEEE 802.3x
Memory
64 Mbytes DDR SDRAM
16 Mbytes Flash
PoE
Passive PoE
Interface
Wireless IEEE 802.11b/g/n, 2T2R
PoE LAN (LAN 1): 1 x 10/100BASE-TX, auto-MDI/MDIX, 24V passive PoE In
LAN 2: 1 x 10/100BASE-TX, auto-MDI/MDIX
Button
Reset button
LED
PWR, LAN, WLAN, Signal Strength
Dimensions (W x D x H)
100 x 29 x 186mm (without antennas)
100 x 29 x 380mm (with antennas)
100 x 29 x 186mm
Weight
300g (without antennas)
332g (with antennas)
300g
Power Consumption
Maximum 7.2W
Power Requirements
LAN1
24V DC, 0.6A (Passive PoE)
Pin 4, 5 V DC+
Pin 7, 8 V DC-
Mounting Type
Mast, wall mount
Wireless Interface Specifications
Antenna
Built-in 5dBi detachable
omnidirectional antennas with RP-
SMA
connectors
HPBW Horizontal: 360 degrees
HPBW Vertical: 30 degrees
Built-
in 8dBi directional antenna with dual
polarization
[Port1]
HPBW Horizontal: 78 degrees
HPBW Vertical: 45 degrees
[Port2]
HPBW Horizontal: 54 degrees
HPBW Vertical: 59 degrees
Data Rate
IEEE 802.11b: 1, 2, 5.5, 11Mbps
IEEE 802.11g: up to 54Mbps
IEEE 802.11n (20MHz): up to 150Mbps
IEEE 802.11n (40MHz): up to 300Mbps
User Manual of WAP-200N/WBS-200N
-12-
Media Access Control
CSMA/CA
Modulation
Transmission/Emission type: OFDM
Data Modulation type: OFDM with BPSK, QPSK, 16-QAM, 64-QAM
Frequency Band
2.412GHz ~ 2.472GHz
Operating Channel
United States -- FCC: 2.414~2.462GHz (11 channels)
Europe -- ETSI: 2.412~2.472GHz (13 channels)
RF Output Power (dBm)
FCC: IEEE 802.11b/g/n: up to 26 ± 2dBm
ETSI: IEEE 802.11b/g/n: < 20dBm (EIRP)
Receiver Sensitivity
(dBm)
IEEE 802.11b:
-95/ -93dBm (1~2/ 5.5~11Mbps)
IEEE 802.11g:
-95/ -93/ -92/ -80/ -77/ -75dBm (6/ 9~18/ 24/ 36/ 48/ 54Mbps)
IEEE 802.11n:
MCS0/ MCS8: -95dBm
MCS1/ MCS9: -93dBm
MCS2/ MCS10: -92dBm
MCS3/ MCS11: -90dBm
MCS4/ MCS12: -86dBm
MCS5/ MCS13: -83dBm
MCS6/ MCS14: -76dBm
MCS7/ MCS15: -73dBm
Environment & Certification
Operating Temperature
-20~70 degrees C
Operating Humidity
10~90% (non-condensing)
IP Level
IP55
Regulatory
CE, FCC, RoHS
Software Features
LAN
Static IP
Dynamic IP
DHCP server in WISP mode
Supports 802.1d STP (Spanning Tree)
WAN Connection Type
(WISP Mode only)
Static IP
Dynamic IP
PPPoE
PPTP
Wireless Modes
Access Point
Client Bridge
WDS (AP/Bridge/Station)
Client Router (WISP)/Client AP Router (WISP+AP)
Repeater
User Manual of WAP-200N/WBS-200N
-13-
Firewall
Offers DoS protection to guard user's content network against DoS attacks
Built-in DMZ and Port Forwarding
VPN Pass-through:
PPTP Pass-through
L2TP Pass-through
IPSec Pass-through
Channel Width
20MHz/40MHz
Encryption Type
64-/128-/152-bit WEP, WPA, WPA-PSK, WPA2, WPA2-PSK, 802.1X
Wireless Security
Enable/Disable SSID Broadcast
Wireless MAC address filtering up to 50 entries
VAP Separation, Station Separation
Max. Wireless Clients
Max. 64 (Suggested 32, depending on usage)
Max. SSIDs
Up to 4
Max. WDS Peers
Up to 4
Wireless QoS
Supports Wi-Fi Multimedia (WMM)
Supports Wireless Traffic Shaping per Radio
Wireless Advanced
Control
Auto Channel Selection
Auto Transmit Power by Regular Domains
Client Limit Control
Distance Control (Auto Ack Timeout)
Wi-Fi Schedule
Status Monitoring
Connection Status
Device Discovery, PLANET Smart Discovery
Wireless Client List/WDS Link List
DHCP Client Table
System Log supports remote syslog server
Signal Strength LEDs in Client Bridge and WDS Station modes
VLAN
VLAN pass-through over WDS
SSID-to-VLAN mapping
Management VLAN (VID: 1~4094)
Self-healing
Supports auto reboot settings
NTP
Network Time Management
Management
Web-based UI, CLI (Command Line Interface) supported
Configuration backup and restore
SNMP v1/v2c/v3 support, MIB I/II, Private MIB
Diagnostic Tools
Built-in Ping, Trace Route, Speed Test Tools
User Manual of WAP-200N/WBS-200N
-14-
Chapter 2. Hardware Installation
2.1 Hardware Description
Dimensions (W x D x H): 100 x 29 x 186mm (without antennas)/100 x 29 x 380mm (with 5dBi antennas)
Figure 2-1 Three-way View (WAP-200N)
Figure 2-2 Three-way View (WBS-200N)
User Manual of WAP-200N/WBS-200N
-15-
Rear PanelLED
Figure 2-3 Rear Panel (WAP-200N)
Figure 2-4 Rear Panel (WBS-200N)
User Manual of WAP-200N/WBS-200N
-16-
LED Definition
LED State Meaning
Power
On The device is powered on
Off The device is powered off
LAN Ports
On Port linked
Blinking Data is transmitting or receiving data
Off No link
WLAN
On The wireless radio is on
Blinking Data is transmitting or receiving over wireless
Off The wireless radio is off
Signal Strength
(Client Bridge/WDS
Station/Client Router
mode only)
Green LED on
Signal is good
Orange LED on
Signal is normal
Red LED on
Signal is poor
Table 2-1 The LED indication
2.1.1 The Bottom Panel
The Bottom panel provides the physical connectors connected to the power adapter and any other network
device. Figure 2-5 shows the bottom panel of the WAP-200N/WBS-200N.
User Manual of WAP-200N/WBS-200N
-17-
Bottom Panel
Figure 2-5 Bottom Panel (WAP-200N/WBS-200N)
PoE Warning Label
Figure 2-6 PoE Warning Label
Hardware Interface Definition
Object Description
Antenna Connectors
(WAP-200N only)
2 RP-SMA (Female) antenna connectors
Passive PoE LAN Port
10/100Mbps RJ45 port, auto MDI/MDI-X
Passive PoE/PD supported, 24V DC In
Pin assignment:
Pins 4, 5 (+)
Pins 7, 8 (-)
NOTE: Please use the 24V DC Passive PoE only (included)
LAN Port
10/100Mbps RJ45 port, auto MDI/MDI-X
Reset Button
Press and hold the Reset button on the device for over 10 seconds
to return to the factory default setting.
Table 2-2 Hardware Interface Definition
User Manual of WAP-200N/WBS-200N
-18-
Chapter 3. Connecting to the AP
3.1 Preparation before Installation
3.1.1 Professional Installation Required
Please seek assistance from a professional installer who is well trained in the RF installation and knowledgeable
in the local regulations.
3.1.2 Safety Precautions
1. To keep you safe and install the hardware properly, please read and follow these safety precautions.
2. If you are installing the WBS-200N or WAP-200N for the first time, for your safety as well as others’,
please seek assistance from a professional installer who has received safety training on the hazards
involved.
3. Keep safety as well as performance in mind when selecting your installation site, especially where there
are electric power and phone lines.
4. When installing the WBS-200N or WAP-200N, please note the following things:
Do not use a metal ladder;
Do not work on a wet or windy day;
Wear shoes with rubber soles and heels, rubber gloves, long sleeved shirt or jacket.
5. When the system is operational, avoid standing directly in front of it. Strong RF fields are present when the
transmitter is on.
3.2 Installation Precautions
Users MUST use a proper and well-installed surge arrestor and grounding kit with WBS-200N or
WAP-200N; otherwise, a random lightning could easily cause fatal damage to the WBS-200N or
WAP-200N. EMD (Lightning) DAMAGE IS NOT COVERED UNDER WARRANTY.
Users MUST use the “Power Cord and PoE Injector” shipped in the box with the WBS-200N or
WAP-200N. Use of other options will cause damage to the WBS-200N or WAP-200N.
User Manual of WAP-200N/WBS-200N
-19-
OUTDOOR INSTALLATION WARNING
IMPORTANT SAFETY PRECAUTIONS:
LIVES MAY BE AT RISK! Carefully observe these instructions and any special instructions that are included with the
equipment you are installing.
CONTACTING POWER LINES CAN BE LETHAL. Make sure no power
lines are anywhere where possible contact can be made. Antennas, masts,
towers, guy wires or cables may lean or fall and contact these lines. People
may be injured or killed if they are touching or holding any part of equipment
when it contacts electric lines. Make sure that equipment or personnel do
not come in contact directly or indirectly with power lines.
The horizontal distance from a tower, mast or antenna to the nearest power
line should be at least twice the total length of the mast/antenna
combination. This will ensure that the mast will not contact power if it falls either during installation or later.
TO AVOID FALLING, USE SAFE PROCEDURES WHEN WORKING AT HEIGHTS ABOVE GROUND.
Select equipment locations that will allow safe, simple equipment installation.
Don’t work alone. A friend or co-worker can save your life if an accident happens.
Use approved non-conducting lasers and other safety equipment. Make sure all equipment is in good repair.
If a tower or mast begins falling, don’t attempt to catch it. Stand back and let it fall.
If anything such as a wire or mast does come in contact with a power line, DON’T TOUCH IT OR ATTEMPT TO
MOVE IT. Instead, save your life by calling the power company.
Don’t attempt to erect antennas or towers on windy days.
MAKE SURE ALL TOWERS AND MASTS ARE SECURELY GROUNDED, AND ELECTRICAL CABLES CONNECTED TO
ANTENNAS HAVE LIGHTNING ARRESTORS. This will help prevent fire damage or human injury in case of lightning, static
build-up, or short circuit within equipment connected to the antenna.
The base of the antenna mast or tower must be connected directly to the building protective ground or to one or more
approved grounding rods, using 1 OAWG ground wire and corrosion-resistant connectors.
Refer to the National Electrical Code for grounding details.
IF A PERSON COMES IN CONTACT WITH ELECTRICAL POWER, AND CANNOT MOVE:
DON’T TOUCH THAT PERSON, OR YOU MAY BE ELECTROCUTED.
Use a non-conductive dry board, stick or rope to push or drag them so they no longer are in contact with electrical
power.
Once they are no longer contacting electrical power, administer CPR if you are certified, and make sure that emergency
medical aid has been requested.
!
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118

Planet UL9200N Manuale utente

Categoria
Router
Tipo
Manuale utente
Questo manuale è adatto anche per

in altre lingue