Planet UL9200N Manuale utente

I

Copyright

reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or

computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical,

manual or otherwise, without the prior written permission of PLANET.

PLANET makes no representations or warranties, either expressed or implied, with respect to the

contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular

purpose. Any software described in this manual is sold or licensed "as is". Should the programs

prove defective following their purchase, the buyer (and not this company, its distributor, or its dealer)

assumes the entire cost of all necessary servicing, repair, and any incidental or consequential

damages resulting from any defect in the software. Further, this company reserves the right to revise

this publication and to make changes from time to time in the contents hereof without obligation to

notify any person of such revision or changes.

All brand and product names mentioned in this manual are trademarks and/or registered trademarks of

their respective holders.

FCC Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance

with the instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by turning the equipment

off and on, the user is encouraged to try to correct the interference by one or more of the following

measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

- Consult the dealer or an experienced radio/TV technician for help.

FCC Caution:

Any changes or modifications not expressly approved by the party responsible for compliance could

void the user’s authority to operate the equipment. This transmitter must not be co-located or operating

in conjunction with any other antenna or transmitter. To assure continued compliance, for example, use

only shielded interface cables when connecting to computer or peripheral devices.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference

(2) This device must accept any interference received, including interference that may cause undesired

operation.

II

This transmitter must not be co-located or operating in conjunction with any other antenna or

transmitter.

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.

This equipment should be installed and operated with a minimum distance of 21cm between the

radiator and your body.

CE Compliance Statement

This device meets the RED directive 2014/53/EU of EU requirements on the limitation of exposure of

the general public to electromagnetic fields by way of health protection.

The device complies with RF

specifications in that the distance between the device and your body should not be less than 20 cm.

Safety

This equipment is designed with the utmost care for the safety of those who install and use it. However,

special attention must be paid to the dangers of electric shock and static electricity when working with

electrical equipment. All guidelines must be followed at all times to ensure the safe use of the

equipment.

WEEE regulation

To avoid the potential effects on the environment and human health as a result of the presence of

hazardous substances in electrical and electronic equipment, end users of electrical and

electronic equipment should understand the meaning of the crossed-out wheeled bin

symbol. Do not dispose of WEEE as unsorted municipal waste; WEEE should be collected

separately.

Revision

User Manual of PLANET 2.4GHz 300Mbps 802.11n Outdoor Wireless AP/CPE

Model: WAP-200N/WBS-200N

Rev: 1.0 (August, 2017)

Part No. EM-WAP-200N_WBS-200N_v1.0

III

CONTENTS

Chapter 1. Product Introduction ........................................................................................................... 7

1.1 Package Contents ............................................................................................................... 7

1.2 Product Description ............................................................................................................ 8

1.3 Product Features ............................................................................................................... 10

1.4 Product Specifications ..................................................................................................... 11

Chapter 2. Hardware Installation ........................................................................................................ 14

2.1 Hardware Description ....................................................................................................... 14

2.1.1 The Bottom Panel ................................................................................................... 16

Chapter 3. Connecting to the AP ........................................................................................................ 18

3.1 Preparation before Installation ........................................................................................ 18

3.1.1 Professional Installation Required .......................................................................... 18

3.1.2 Safety Precautions .................................................................................................. 18

3.2 Installation Precautions .................................................................................................... 18

3.3 Installing the AP ................................................................................................................ 20

Chapter 4. Quick Installation Guide ................................................................................................... 22

4.1 Manual Network Setup -- TCP/IP Configuration ............................................................. 22

4.1.1 Configuring the IP Address Manually ..................................................................... 22

4.2 Starting Setup in the Web UI ............................................................................................ 25

Chapter 5. Configuring the AP ............................................................................................................ 27

5.1 Operation Mode ................................................................................................................. 27

5.1.1 Access Point (AP) ................................................................................................... 29

5.1.2 Client Bridge (CB) ................................................................................................... 30

5.1.3 WDS Access Point (WDS AP) ................................................................................ 31

5.1.4 WDS Station (WDS STA) ........................................................................................ 32

5.1.5 WDS Bridge (WDS PtP/WDS PtMP) ...................................................................... 33

5.1.6 Client Router (CR/WISP) ........................................................................................ 39

5.1.7 Repeater ................................................................................................................. 45

5.2 Status.................................................................................................................................. 49

5.2.1 Main ........................................................................................................................ 49

5.2.2 Save/Reload ........................................................................................................... 51

5.2.3 Wireless Client List ................................................................................................. 52

5.2.4 WDS Link List ......................................................................................................... 53

5.2.5 DHCP Client Table .................................................................................................. 53

5.2.6 Connection Status ................................................................................................... 54

5.2.7 System Log ............................................................................................................. 55

5.3 System ................................................................................................................................ 56

5.3.1 IP Settings ............................................................................................................... 56

IV

5.3.2 Spanning Tree Settings (STP) ................................................................................ 57

5.4 Router (WISP Mode Only) ................................................................................................. 58

5.4.1 DHCP Server Settings ............................................................................................ 58

5.4.2 WAN Settings .......................................................................................................... 59

5.4.2.1. DHCP ............................................................................................................................. 60

5.4.2.2. Static IP .......................................................................................................................... 61

5.4.2.3. PPPoE ........................................................................................................................... 63

5.4.2.4. PPTP ............................................................................................................................. 64

5.4.3 VPN Pass Through ................................................................................................. 65

5.4.4 Port Forwarding ...................................................................................................... 66

5.4.5 DMZ Settings .......................................................................................................... 67

5.5 Wireless .............................................................................................................................. 68

5.5.1 Wireless Network .................................................................................................... 68

5.5.2 WDS Link Settings .................................................................................................. 71

5.5.3 Security Settings ..................................................................................................... 73

5.5.4 Wireless MAC Filter ................................................................................................ 83

5.5.5 Wireless Advanced Settings ................................................................................... 84

5.6 Management ...................................................................................................................... 85

5.6.1 Administration (Password Settings) ........................................................................ 85

5.6.2 Management VLAN ................................................................................................ 86

5.6.3 SNMP Settings ....................................................................................................... 87

5.6.4 Backup/Restore Settings ........................................................................................ 88

5.6.5 Auto Reboot Settings .............................................................................................. 89

5.6.6 Firmware Upgrade .................................................................................................. 89

5.6.7 Time Settings .......................................................................................................... 91

5.6.8 Wi-Fi Schedule ....................................................................................................... 92

5.6.9 CLI Settings ............................................................................................................ 93

5.6.10 Log .......................................................................................................................... 93

5.6.11 Diagnostics ............................................................................................................. 94

5.6.12 Logout ..................................................................................................................... 95

Appendix A: Troubleshooting ............................................................................................................ 96

Appendix B: Use Planet Smart Discovery to find AP ...................................................................... 98

Appendix C: FAQ ................................................................................................................................. 99

Q1: How to set up the AP Client Connection ........................................................................... 99

Q2: How to set up the WDS Connection ................................................................................ 108

V

FIGURES

FIGURE 2-1 THREE-WAY VIEW (WAP-200N) ........................................................................................................ 14

FIGURE 2-2 THREE-WAY VIEW (WBS-200N) ........................................................................................................ 14

FIGURE 2-3 REAR PANEL (WAP-200N) ................................................................................................................ 15

FIGURE 2-4 REAR PANEL (WBS-200N) ................................................................................................................ 15

FIGURE 2-5 BOTTOM PANEL (WAP-200N/WBS-200N) ........................................................................................ 17

FIGURE 2-6 POE WARNING LABEL ....................................................................................................................... 17

FIGURE 3-1 POE AND LAN PORT CONNECTION ..................................................................................................... 20

FIGURE 3-2 FINISH INSTALLATION AND CONNECT TO ANTENNAS (WAP-200N ONLY) ........................................... 20

FIGURE 3-3 POLE MOUNTING ............................................................................................................................... 21

FIGURE 3-4 WALL MOUNTING .............................................................................................................................. 21

FIGURE 4-1 TCP/IP SETTING ................................................................................................................................ 23

FIGURE 4-2 WINDOWS START MENU .................................................................................................................... 24

FIGURE 4-3 SUCCESSFUL RESULT OF PING COMMAND .......................................................................................... 24

FIGURE 4-4 FAILED RESULT OF PING COMMAND ................................................................................................... 25

FIGURE 4-5 LOGIN BY DEFAULT IP ADDRESS ......................................................................................................... 25

FIGURE 4-6 LOGIN WINDOW ................................................................................................................................ 25

FIGURE 4-7 WEB UI SCREENSHOT ........................................................................................................................ 26

FIGURE 5-1 OPERATION MODE – ALL ................................................................................................................... 28

FIGURE 5-2 OPERATION MODE – AP ..................................................................................................................... 29

FIGURE 5-3 OPERATION MODE – CLIENT BRIDGE ................................................................................................. 30

FIGURE 5-4 OPERATION MODE – WDS AP ........................................................................................................... 31

FIGURE 5-5 OPERATION MODE – WDS STATION ................................................................................................... 32

FIGURE 5-6 OPERATION MODE – WDS BRIDGE .................................................................................................... 33

FIGURE 5-7 OPERATION MODE – CLIENT ROUTER (WISP) ................................................................................... 39

FIGURE 5-8 OPERATION MODE – REPEATER ......................................................................................................... 45

FIGURE 5-9 SYSTEM MENU - RESET ..................................................................................................................... 49

FIGURE 5-10 SYSTEM MENU – LANGUAGE OPTION .............................................................................................. 49

FIGURE 5-11 MAIN STATUS ................................................................................................................................... 50

FIGURE 5-12 SAVE/RELOAD ................................................................................................................................. 51

FIGURE 5-13 SAVE/RELOAD - DEFAULT ................................................................................................................ 52

FIGURE 5-14 WIRELESS CLIENT LIST ................................................................................................................... 52

FIGURE 5-15 KICK THE CLIENT ............................................................................................................................. 52

FIGURE 5-16 WDS LINK STATUS .......................................................................................................................... 53

FIGURE 5-17 DHCP CLIENT LIST ......................................................................................................................... 53

FIGURE 5-18 CONNECTION STATUS ...................................................................................................................... 54

FIGURE 5-19 SYSTEM LOG ................................................................................................................................... 55

FIGURE 5-20 LAN IP SETTINGS ............................................................................................................................ 56

FIGURE 5-21 SPANNING TREE SETTINGS ............................................................................................................... 57

FIGURE 5-22 DHCP SERVER SETTINGS ................................................................................................................ 58

FIGURE 5-23 WAN SETTINGS – ALL ..................................................................................................................... 59

FIGURE 5-24 WAN SETTINGS – DHCP ................................................................................................................. 61

FIGURE 5-25 WAN SETTINGS – STATIC IP ............................................................................................................ 62

VI

FIGURE 5-26 WAN SETTINGS – PPPOE ................................................................................................................ 63

FIGURE 5-27 WAN SETTINGS – PPTP .................................................................................................................. 64

FIGURE 5-28 VPN PASS THROUGH ....................................................................................................................... 65

FIGURE 5-29 PORT FORWARDING .......................................................................................................................... 66

FIGURE 5-30 PORT FORWARDING .......................................................................................................................... 67

FIGURE 5-31 DMZ ............................................................................................................................................... 68

FIGURE 5-32 WIRELESS NETWORK – AP/WDS AP MODE .................................................................................... 69

FIGURE 5-33 WIRELESS NETWORK – SSID PROFILE............................................................................................. 69

FIGURE 5-34 WIRELESS NETWORK – CB/WDS STA/CR/REPEATER MODE ......................................................... 71

FIGURE 5-35 WDS LINK SETTINGS – WDS BRIDGE MODE .................................................................................. 72

FIGURE 5-36 SECURITY SETTINGS – AP/WDS AP MODE ..................................................................................... 73

FIGURE 5-37 SECURITY SETTINGS – CB/WDS STA/CR/REPEATER MODE ........................................................... 73

FIGURE 5-38 SECURITY SETTINGS – WDS BRIDGE MODE .................................................................................... 74

FIGURE 5-39 SECURITY SETTINGS – WEP ............................................................................................................ 75

FIGURE 5-40 SECURITY SETTINGS – WPA-PSK .................................................................................................... 76

FIGURE 5-41 SECURITY SETTINGS – WPA2-PSK .................................................................................................. 77

FIGURE 5-42 SECURITY SETTINGS – WPA-PSK MIXED ........................................................................................ 77

FIGURE 5-43 SECURITY SETTINGS – WPA (WPA ENTERPRISE) ............................................................................. 78

FIGURE 5-44 SECURITY SETTINGS – WPA2 (WPA2 ENTERPRISE) ........................................................................ 79

FIGURE 5-45 SECURITY SETTINGS – WPA MIXED (WPA MIXED ENTERPRISE) ..................................................... 81

FIGURE 5-46 WIRELESS MAC FILTER .................................................................................................................. 83

FIGURE 5-47 WIRELESS ADVANCED SETTINGS ..................................................................................................... 84

FIGURE 5-48 ADMINISTRATION (PASSWORD SETTINGS) ........................................................................................ 86

FIGURE 5-49 MANAGEMENT VLAN ..................................................................................................................... 86

FIGURE 5-50 SNMP SETTINGS ............................................................................................................................. 87

FIGURE 5-51 BACKUP/RESTORE SETTINGS ........................................................................................................... 88

FIGURE 5-52 AUTO REBOOT SETTINGS ................................................................................................................. 89

FIGURE 5-53 FIRMWARE UPGRADE ....................................................................................................................... 89

FIGURE 5-54 TIME SETTINGS ................................................................................................................................ 91

FIGURE 5-55 WI-FI SCHEDULE ............................................................................................................................. 92

FIGURE 5-56 CLI SETTINGS .................................................................................................................................. 93

FIGURE 5-57 LOG ................................................................................................................................................. 93

FIGURE 5-58 DIAGNOSTICS................................................................................................................................... 94

FIGURE 5-59 LOGOUT ........................................................................................................................................... 95

User Manual of WAP-200N/WBS-200N

-7-

Chapter 1. Product Introduction

1.1 Package Contents

Thank you for choosing PLANET WAP-200N/WBS-200N series. Before installing the AP/CPE, please verify the

contents inside the package box.

WBS-200N / WAP-200N Quick Installation Guide Mounting Strap x 2

Screw Set x 1 PoE Injector & Power Cord Antenna x 2 (WAP-200N only)

If there is any item missing or damaged, please contact the seller

immediately.

User Manual of WAP-200N/WBS-200N

-8-

1.2 Product Description

Cost-effective Wireless Solution with Superior Performance

PLANET WAP-200N/WBS-200N 300Mbps 802.11n Outdoor Wireless AP/CPE offers a better range and

excellent throughput. Via the WAP-200N's RP-SMA antenna connectors and the WBS-200N's embedded 8dBi

dual-polarity directional antenna, it is easy to build different point to multi-point applications with good diversity

coverage and better noise immunity effect, thus heightening the performance and stability of a long-distance

connectivity.

Designed for Various Requirements

The WAP-200N/WBS-200N is dedicatedly designed for WISP solution that provides CPE users with Internet

access via the WISP provider in rural areas. Besides, it caters to various wireless communication connectivities

(AP, Client, WDS, Repeater and WISP), thus meeting users’ application requirements.

User Manual of WAP-200N/WBS-200N

-9-

Multiple SSIDs with VLAN Tagging

Multiple SSIDs can broadcast up to four wireless networks with different names. For management purposes, the

IEEE 802.1Q VLAN supported allows multiple VLAN tags to be mapped to multiple SSIDs to distinguish the

wireless access. This makes it possible for the WAP-200N/WBS-200N to work with managed Ethernet switches

to have VLANs assigned for a different access level and authority.

Flexible and Reliable Outdoor Characteristics

The WAP-200N/WBS-200N is definitely suitable for wireless IP surveillance to enable to have wide deployments

between buildings and to act as the backbone of public service. Additionally, its self-healing capability keeps

connection alive all the time. With the IP55-rated outdoor UV-resistant enclosure, the WAP-200N/WBS-200N

can perform normally under rigorous weather conditions, meaning it can be installed in any harsh, outdoor

environments. With the proprietary Power over Ethernet (PoE) design, the WAP-200N/WBS-200N can be

easily installed in the areas where power outlets are not available.

Advanced Security and Rigorous Authentication

The WAP-200N/WBS-200N supports 152-bit WEP, WPA/WPA2, WPA-PSK and WPA2-PSK wireless encryptions,

the advanced WPA2-AES mechanism and 802.1X RADIUS authentication, which can effectively prevent

eavesdropping by unauthorized users or bandwidth occupied by unauthenticated wireless access. Furthermore,

any users are granted or denied access to the wireless LAN network based on the ACL (Access Control List)

that the administrator pre-established.

Easy Deployment and Management

With user-friendly Web UI and comprehensive management features including client limit control and wireless

traffic shaping, the WAP-200N/WBS-200N is easy to limit the client access and inbound/outbound bandwidth

control, even for users who have no experience in setting up a wireless network. Furthermore, with the Planet

Smart Discovery Utility, SNMP and diagnostics tools, the WAP-200N/WBS-200N is convenient to be managed

remotely.

User Manual of WAP-200N/WBS-200N

-10-

1.3 Product Features

 Industrial Compliant Wireless LAN

 Compliant with the IEEE 802.11b/g/n wireless technology

 2T2R architecture with data rate of up to 300Mbps

 Equipped with two 10/100Mbps RJ45 ports, with auto MDI/MDI-X supported

 Fixed Network Broadband Router

 Supported WAN connection types in WISP mode: DHCP, Static IP, PPPoE, PPTP

 Supports Port Forwarding and DMZ for various networking applications

 Supports DHCP server in WISP mode

 RF Interface Characteristics

 Built-in 5dBi detachable antennas with RP-SMA connectors (WAP-200N)

 Built-in 8dBi dual-polarization antenna (WBS-200N)

 High output power with multiply-adjustable transmit power control

 Outdoor Environmental Characteristics

 IP55 rating

 Passive Power over Ethernet design

 Operating temperature: -20~70°C

 Multiple Operation Modes and Wireless Features

 Multiple operation modes: AP, Client Bridge, Client Router (WISP), WDS, Repeater

 WMM (Wi-Fi multimedia) provides higher priority to multimedia transmitting over wireless

 Wireless Traffic Shaping to control the upload/download bandwidth

 Wi-Fi scheduler allows to be enabled or disabled based on predefined schedule

 Secure Network Connection

 Full encryption supported: 64-/128-/152-bit WEP, WPA/WPA2, WPA-PSK/WPA2-PSK and 802.1X

RADIUS authentication

 Supports 802.1Q VLAN pass-through over WDS and SSID-to-VLAN mapping

 Supports up to 50 entries of MAC address filtering

 Easy Installation and Management

 IPv4/IPv6 dual-stack management networks

 Multilingual Web User Interface: English, Spanish, French, German, Portuguese, Russian, and

Simplified Chinese

 CLI command and SNMP-based management interface

 Self-healing mechanism through system auto reboot setting

 System status monitoring through remote Syslog Server and Device Discovery

 Diagnostic tools include Ping, Traceroute, Speed

 Planet Smart Discovery Utility allows administrator to discover and locate each AP

User Manual of WAP-200N/WBS-200N

-11-

1.4 Product Specifications

Product

WAP-200N

WBS-200N

2.4GHz 300Mbps 802.11n Outdoor Wireless AP/CPE

Hardware Features

Standard Support

IEEE802.11b/g/n

IEEE 802.3

IEEE 802.3u

IEEE 802.3x

Memory

64 Mbytes DDR SDRAM

16 Mbytes Flash

PoE

Passive PoE

Interface

Wireless IEEE 802.11b/g/n, 2T2R

PoE LAN (LAN 1): 1 x 10/100BASE-TX, auto-MDI/MDIX, 24V passive PoE In

LAN 2: 1 x 10/100BASE-TX, auto-MDI/MDIX

Button

Reset button

LED

PWR, LAN, WLAN, Signal Strength

Dimensions (W x D x H)

100 x 29 x 186mm (without antennas)

100 x 29 x 380mm (with antennas)

100 x 29 x 186mm

Weight

300g (without antennas)

332g (with antennas)

300g

Power Consumption

Maximum 7.2W

Power Requirements

LAN1

 24V DC, 0.6A (Passive PoE)

 Pin 4, 5 V DC+

 Pin 7, 8 V DC-

Mounting Type

Mast, wall mount

Wireless Interface Specifications

Antenna

Built-in 5dBi detachable

omnidirectional antennas with RP-

SMA

connectors

HPBW Horizontal: 360 degrees

HPBW Vertical: 30 degrees

Built-

in 8dBi directional antenna with dual

polarization

[Port1]

HPBW Horizontal: 78 degrees

HPBW Vertical: 45 degrees

[Port2]

HPBW Horizontal: 54 degrees

HPBW Vertical: 59 degrees

Data Rate

IEEE 802.11b: 1, 2, 5.5, 11Mbps

IEEE 802.11g: up to 54Mbps

IEEE 802.11n (20MHz): up to 150Mbps

IEEE 802.11n (40MHz): up to 300Mbps

User Manual of WAP-200N/WBS-200N

-12-

Media Access Control

CSMA/CA

Modulation

Transmission/Emission type: OFDM

Data Modulation type: OFDM with BPSK, QPSK, 16-QAM, 64-QAM

Frequency Band

2.412GHz ~ 2.472GHz

Operating Channel

United States -- FCC: 2.414~2.462GHz (11 channels)

Europe -- ETSI: 2.412~2.472GHz (13 channels)

RF Output Power (dBm)

FCC: IEEE 802.11b/g/n: up to 26 ± 2dBm

ETSI: IEEE 802.11b/g/n: < 20dBm (EIRP)

Receiver Sensitivity

(dBm)

IEEE 802.11b:

-95/ -93dBm (1~2/ 5.5~11Mbps)

IEEE 802.11g:

-95/ -93/ -92/ -80/ -77/ -75dBm (6/ 9~18/ 24/ 36/ 48/ 54Mbps)

IEEE 802.11n:

MCS0/ MCS8: -95dBm

MCS1/ MCS9: -93dBm

MCS2/ MCS10: -92dBm

MCS3/ MCS11: -90dBm

MCS4/ MCS12: -86dBm

MCS5/ MCS13: -83dBm

MCS6/ MCS14: -76dBm

MCS7/ MCS15: -73dBm

Environment & Certification

Operating Temperature

-20~70 degrees C

Operating Humidity

10~90% (non-condensing)

IP Level

IP55

Regulatory

CE, FCC, RoHS

Software Features

LAN

 Static IP

 Dynamic IP

 DHCP server in WISP mode

Supports 802.1d STP (Spanning Tree)

WAN Connection Type

(WISP Mode only)

 Static IP

 Dynamic IP

 PPPoE

 PPTP

Wireless Modes

 Access Point

 Client Bridge

 WDS (AP/Bridge/Station)

 Client Router (WISP)/Client AP Router (WISP+AP)

 Repeater

User Manual of WAP-200N/WBS-200N

-13-

Firewall

Offers DoS protection to guard user's content network against DoS attacks

Built-in DMZ and Port Forwarding

VPN Pass-through:

 PPTP Pass-through

 L2TP Pass-through

 IPSec Pass-through

Channel Width

20MHz/40MHz

Encryption Type

64-/128-/152-bit WEP, WPA, WPA-PSK, WPA2, WPA2-PSK, 802.1X

Wireless Security

Enable/Disable SSID Broadcast

Wireless MAC address filtering up to 50 entries

VAP Separation, Station Separation

Max. Wireless Clients

Max. 64 (Suggested 32, depending on usage)

Max. SSIDs

Up to 4

Max. WDS Peers

Up to 4

Wireless QoS

Supports Wi-Fi Multimedia (WMM)

Supports Wireless Traffic Shaping per Radio

Wireless Advanced

Control

Auto Channel Selection

Auto Transmit Power by Regular Domains

Client Limit Control

Distance Control (Auto Ack Timeout)

Wi-Fi Schedule

Status Monitoring

Connection Status

Device Discovery, PLANET Smart Discovery

Wireless Client List/WDS Link List

DHCP Client Table

System Log supports remote syslog server

Signal Strength LEDs in Client Bridge and WDS Station modes

VLAN

VLAN pass-through over WDS

SSID-to-VLAN mapping

Management VLAN (VID: 1~4094)

Self-healing

Supports auto reboot settings

NTP

Network Time Management

Management

Web-based UI, CLI (Command Line Interface) supported

Configuration backup and restore

SNMP v1/v2c/v3 support, MIB I/II, Private MIB

Diagnostic Tools

Built-in Ping, Trace Route, Speed Test Tools

User Manual of WAP-200N/WBS-200N

-14-

Chapter 2. Hardware Installation

2.1 Hardware Description

 Dimensions (W x D x H): 100 x 29 x 186mm (without antennas)/100 x 29 x 380mm (with 5dBi antennas)

Figure 2-1 Three-way View (WAP-200N)

Figure 2-2 Three-way View (WBS-200N)

User Manual of WAP-200N/WBS-200N

-15-

Rear Panel – LED

Figure 2-3 Rear Panel (WAP-200N)

Figure 2-4 Rear Panel (WBS-200N)

User Manual of WAP-200N/WBS-200N

-16-

LED Definition

LED State Meaning

Power

On The device is powered on

Off The device is powered off

LAN Ports

On Port linked

Blinking Data is transmitting or receiving data

Off No link

WLAN

On The wireless radio is on

Blinking Data is transmitting or receiving over wireless

Off The wireless radio is off

Signal Strength

(Client Bridge/WDS

Station/Client Router

mode only)

Green LED on

Signal is good

Orange LED on

Signal is normal

Red LED on

Signal is poor

Table 2-1 The LED indication

2.1.1 The Bottom Panel

The Bottom panel provides the physical connectors connected to the power adapter and any other network

device. Figure 2-5 shows the bottom panel of the WAP-200N/WBS-200N.

User Manual of WAP-200N/WBS-200N

-17-

Bottom Panel

Figure 2-5 Bottom Panel (WAP-200N/WBS-200N)

PoE Warning Label

Figure 2-6 PoE Warning Label

Hardware Interface Definition

Object Description

Antenna Connectors

(WAP-200N only)

2 RP-SMA (Female) antenna connectors

Passive PoE LAN Port

10/100Mbps RJ45 port, auto MDI/MDI-X

Passive PoE/PD supported, 24V DC In

Pin assignment:

Pins 4, 5 (+)

Pins 7, 8 (-)

NOTE: Please use the 24V DC Passive PoE only (included)

LAN Port

10/100Mbps RJ45 port, auto MDI/MDI-X

Reset Button

Press and hold the Reset button on the device for over 10 seconds

to return to the factory default setting.

Table 2-2 Hardware Interface Definition

User Manual of WAP-200N/WBS-200N

-18-

Chapter 3. Connecting to the AP

3.1 Preparation before Installation

3.1.1 Professional Installation Required

Please seek assistance from a professional installer who is well trained in the RF installation and knowledgeable

in the local regulations.

3.1.2 Safety Precautions

1. To keep you safe and install the hardware properly, please read and follow these safety precautions.

2. If you are installing the WBS-200N or WAP-200N for the first time, for your safety as well as others’,

please seek assistance from a professional installer who has received safety training on the hazards

involved.

3. Keep safety as well as performance in mind when selecting your installation site, especially where there

are electric power and phone lines.

4. When installing the WBS-200N or WAP-200N, please note the following things:

♦ Do not use a metal ladder;

♦ Do not work on a wet or windy day;

♦ Wear shoes with rubber soles and heels, rubber gloves, long sleeved shirt or jacket.

5. When the system is operational, avoid standing directly in front of it. Strong RF fields are present when the

transmitter is on.

3.2 Installation Precautions

 Users MUST use a proper and well-installed surge arrestor and grounding kit with WBS-200N or

WAP-200N; otherwise, a random lightning could easily cause fatal damage to the WBS-200N or

WAP-200N. EMD (Lightning) DAMAGE IS NOT COVERED UNDER WARRANTY.

 Users MUST use the “Power Cord and PoE Injector” shipped in the box with the WBS-200N or

WAP-200N. Use of other options will cause damage to the WBS-200N or WAP-200N.

User Manual of WAP-200N/WBS-200N

-19-

OUTDOOR INSTALLATION WARNING

IMPORTANT SAFETY PRECAUTIONS:

LIVES MAY BE AT RISK! Carefully observe these instructions and any special instructions that are included with the

equipment you are installing.

CONTACTING POWER LINES CAN BE LETHAL. Make sure no power

lines are anywhere where possible contact can be made. Antennas, masts,

towers, guy wires or cables may lean or fall and contact these lines. People

may be injured or killed if they are touching or holding any part of equipment

when it contacts electric lines. Make sure that equipment or personnel do

not come in contact directly or indirectly with power lines.

The horizontal distance from a tower, mast or antenna to the nearest power

line should be at least twice the total length of the mast/antenna

combination. This will ensure that the mast will not contact power if it falls either during installation or later.

TO AVOID FALLING, USE SAFE PROCEDURES WHEN WORKING AT HEIGHTS ABOVE GROUND.

 Select equipment locations that will allow safe, simple equipment installation.

 Don’t work alone. A friend or co-worker can save your life if an accident happens.

 Use approved non-conducting lasers and other safety equipment. Make sure all equipment is in good repair.

 If a tower or mast begins falling, don’t attempt to catch it. Stand back and let it fall.

 If anything such as a wire or mast does come in contact with a power line, DON’T TOUCH IT OR ATTEMPT TO

MOVE IT. Instead, save your life by calling the power company.

 Don’t attempt to erect antennas or towers on windy days.

MAKE SURE ALL TOWERS AND MASTS ARE SECURELY GROUNDED, AND ELECTRICAL CABLES CONNECTED TO

ANTENNAS HAVE LIGHTNING ARRESTORS. This will help prevent fire damage or human injury in case of lightning, static

build-up, or short circuit within equipment connected to the antenna.

 The base of the antenna mast or tower must be connected directly to the building protective ground or to one or more

approved grounding rods, using 1 OAWG ground wire and corrosion-resistant connectors.

 Refer to the National Electrical Code for grounding details.

IF A PERSON COMES IN CONTACT WITH ELECTRICAL POWER, AND CANNOT MOVE:

 DON’T TOUCH THAT PERSON, OR YOU MAY BE ELECTROCUTED.

 Use a non-conductive dry board, stick or rope to push or drag them so they no longer are in contact with electrical

power.

Once they are no longer contacting electrical power, administer CPR if you are certified, and make sure that emergency

medical aid has been requested.

!

La pagina si sta caricando...

Planet UL9200N Manuale utente

Questo manuale è adatto anche per

Planet UL9200N Manuale utente

in altre lingue

Documenti correlati

Altri documenti