Welch Allyn LumiView Operating Instructions Manual

Tipo
Operating Instructions Manual
WelcljAllyrr
LumiView@
Portable Binocular Microscope
Microscope binoculaire portatif
Microscopio binocular
portzitil
Tragbares Binokular-Mikroskop
Operating Instructions
.......................
1
Instructions de fonctionnement
.....
.18
Instruccioness
de
operacicin
............
.35
Gebrauchsanweisung
.......................... .
lstruzioni per il funzionamento
.........50
.63
Thank
you
for purchasing the Welch Allyn
LumNieti
Portable
Binocular Microscope or Flat Surface Magnifier. To ensure
accurate and reliable performance of your new instrument, please
follow the operating and maintenance instructions found
in
this
manual.
U.S.
and
International
Patents
Pending.
IMPORTANT: The material outlined in this manual should be reviewed and understood
prior to operation of the equipment.
Nous vous remercions d’avoir fait I’acquisition du microscope
binoculaire portatif
ou
la
loupe
à
surface plate
LumiVieti
de
Welch Allyn. Suivez les directives contenues
dans
ce manuel pour
assurer le fonctionnement précis et fiable de votre nouvel
instrument pendant de nombreuses années.
Brevets
U.S. et
internationaux
en
instance.
IMPORTANT
:
Avant d’utiliser I’équipement, bien lire les instructions
données
dans
ce
manual.
Agradecemos su compra del Microscopio binocular portátil o
Lupa de superficie plana
LumiVieti
de Welch Allyn. Para asegurar
un rendimiento preciso y confiable de su nuevo instrumento, siga
las instrucciones de operación y mantenimiento que se
encuentran en este manual.
Patentes
de
los
EE.UU.
e
internacionales pendientes.
IMPORTANTE: El material descrito en este manual debe ser revisado y entendido
antes de operar el equipo.
Wir bedanken
uns
für
den
Kauf des tragbaren
LumiVieHP
Binokular-Mikroskops bzw. der Flachlupe von Welch Allyn. Dieses
Geriit wird stets zuverlässig und störungsfrei arbeiten, wenn es
entsprechend
den
Empfehlungen
in
diesem Handbuch verwendet
und gepflegt wird.
U.S.-Patente und
international
Patente
angemeldet.
WICHTIG:
Der
Anwender sollte vor Benutzung des Geräts mit
den
Informationen
in
diesem Handbuch gründlich vertraut sein.
Grazíe per aver acquistato
il
microscopio binoculare portatile
Lumiview@
o la lente di ingrandimento a superficie piatta
della
Welch Allyn. Per garantire che
il
vostro nuovo strumento offra
prestazioni accurate e attendibili, si prega di seguire le istruzioni
per
il
funzionamento e la manutenzione contenute
in
questo
manuale.
Brevetti statunitensi
e
internationali pendenti.
IMPORTANTE:
il
materiale evidenziato
in
questo manuale deve essere esaminato
e compreso prima di far funzionare I’apparecchiatura.
1
Symbols
a
I
CAUTION: Indicates a potentially hazardous
.
situation which, if not avoided, may result in
minor injury or property damage. It also alerts
against unsafe practices.
NOTE:
Provides
supplemental information to the text and
indicates a potentially hazardous situation, which, if not avoided,
may result in property damage. Additionally, it highlights
important information on the use of this equipment.
Standards Compliance
0
0
Double Insulation
Internally Powered
Listed Product Underwriters Laboratories,
Standard UL544
Listed Product Canadian Standards Association,
Standard CAN/CSA C22.2 No. 125
Listed Product ETL Laboratories
Listed Standards
UL544,
CAN/CSA C22.2
No. 125, IEC 601-1, IEC 601-1-2
Contents
CEApproval
................................................................................
Symbols
......................................................................................
Standards Compliance
..............................................................
Instrument Function
..................................................................
Portable Binocular Microscope
............................................
Flat Surface Magnifier
..........................................................
Descriptionof
Controls..
............................................................
Adjustments
................................................................................
Headband Model
..................................................................
Band Adjustments
........................................................
OpticalSectionHorizontal Adjustment
........................
OpticalSectionVerticalAdjustment..
............................
Spectacle Model
..................................................................
Optical Section Vertical Adjustment
..............................
Adjusting for
UserRefractive
Error
......................................
Lens Template
-
SpectacleModel
..............................
Setting the Interpupillaryy
Distance
......................................
Flat Surface Magnifier..........................................................
Connecting to the Power Source
..............................................
Portable
Power
Source
........................................................
DirectPlug-In
Power Source................................................
Accessories
................................................................................
PneumaticSpeculum
Holder................................................
Lamp Replacement
....................................................................
Cleaning
......................................................................................
Maintenance
................................................................................
Specifications..
............................................................................
Approvals
....................................................................................
Product and Accessory Ordering
Information
........................
Instruments
..........................................................................
Power Sources
......................................................................
Accessories
..........................................................................
Power Sources(Portableand
Direct Plug-In)..........................
Portable
................................................................................
Features
........................................................................
Specifications................................................................
Connecting Instrument to Portable Power Source
......
Recharging the
Portable Power Source......................
Accessing
SpareLamp
................................................
BatteryReplacement..
..................................................
DirectPlug-In Transformer..
..................................................
Service and Warranty Information
............................................
Service
..................................................................................
Technical Service Department
..............................................
Warranty
................................................................................
Troubleshooting
Guide..............................................................
4
2
3
3
5
5
5
6
7
7
7
7
7
8
8
8
8
9
9
10
10
10
11
11
11
12
12
12
12
13
13
13
13
14
14
14
14
15
15
15
16
16
17
17
17
17
18
Instrument Function
This device offers binocular (both eyes) viewing, providing a
three-
dimensional stereoscopic view. This stereoscopic view is then
magnified and illuminated to provide excellent tissue rendition.
Portable Binocular Microscope
When the binoculars are engaged, the visual pathways are displaced
medially to allow for binocular vision in narrow cavities. Two diopters
(1.5x) magnification improves vision.
When the binoculars are rotated upwards, the scope becomes a
convenient basic headlight.
Flat Surface Magnifier
l
The three diopter
(2.5x)
flat surface magnifier is available
in either the headband model or the spectacle model. The
magnifier can be flipped up for convenient headlight use.
a
I
CAUTION: DO NOT look directly into the light.
.
This device contains a High Intensity Lamp. It is
not to be used for illumination or examination of
any portion of the eye, Posterior or Anterior.
5
Description of Controls
Front
View
Back View
3
1
1. lnterpupillary distance (IPD) controls
2. Lamp
3. Instrument vertical height adjustment
1
I
5
/*\
4. Binocular flip-up axis 8. Comfort pads
5. Pivot mechanism
9. Cable clips
6. Height adjustment screw
10. Optical assembly
7. Headband circumference
adjustment knob
Fiat Surface Magnifier
12
11
-
11. Magnifier lens
12. Lens holder
13. Vertical adjustment screw
6
Adjustments
Ratchet Style Headband
Instructions
l
Position the main body of the headband on the head so that the
band fits comfortably on the forehead and low on the back of the
head. Use the circumference adjustment knob to adjust the size.
Optics Assembly
l
The optics assembly can be
adjusted to the desired position
by manipulating the links in the
pivot mechanism. The Optics
Assembly should be positioned
as close to the eyes as possible
so that the eyes can gaze directly
through the Optics Assembly.
(Set optics per instructions
provided with your
LumiView.)
l
With the lamp illuminated,
check the adjustment by
confirming that the light beam
is centered in the visual field.
If the light is high or low, refer
to the detailed adjustment
instructions provided with your
LumiView@.
Circumference
adjustment knob
1
Optical Section
7
Spectacle Model
Optical Section Vertical Adjustment
l
Loosen screw that attaches
optical section spectacles.
l
Reposition optical section to
insure proper alignment with
user’s eyes.
Screw
l
Tighten screw to maintain
optical section location.
Adjusting for User Refractive Error
(Spectacle Models Only)
The optimal working distance from the object is 15” (38.1 cm)
-
17” (43.2 cm). If this model is used without corrective lenses and
user is myopic or hyperopic, then the user will need to work
closer or farther from object, depending on refractive error.
To compensate for this, the spectacle models can be fitted with
corrective lenses by an
eyecare
practitioner of your choice. Please
bring the following information to assist your
eyecare
practitioner
in fitting your prescription lenses.
Lens Template
-
Spectacle Model
Front Sizes
Eye
A
B
51 51
43
1
,
A
I
ED
D.B.L
57.4 18
Setting the lnterpupillaty Distance
The lnterpupillary Distance (IPD) Controls move the oculars and are
located on the bottom of the optical section. These oculars move
independently of one another.
l
To set IPD properly, observe an object at approximately
15 inches (38 cm).
l
Close the left eye and adjust the IPD control under the right eye
until the viewed image is centered.
l
Now close the right eye, keeping the left eye open, and adjust the
IPD control for the left eye until that image is centered.
l
Open both eyes and the object should be clear
and centered.
lnterpupillary Distance Controls
Flat Surface Magnifier Model
l
Loosen screw that attaches the lamp section to the adjustment arm.
l
Reposition the lamp section up or down to desired location and
tighten screw.
l
Place instrument on head. Adjust the flat surface magnifier by
moving the lens holder up or down and the magnifier in or out.
Magnifier
Lens holder
Adjustment screw
9
Connecting to the Power Source
NOTE: The instrument power cord must be plugged into either a
Welch
Allyn
Portable Power Source No. 75250 or a Welch
Allyn
Direct
Plug-In Power
Source
No. 75210.
a
I
CAUTION: The lamp housing becomes hot when the
.
lamp is on for more than 5 minutes and can cause
a burn if it contacts the skin. Allow at least 10 min-
utes for cooling between the uses of the illuminator.
Portable Power Source
l
Plug
instrument power cord
into the power cord connector
port on top of the power source.
l
Push in until firmly in place.
l
Gently screw the external
connector sleeve clockwise
to secure (optional).
l
Attach the Portable Power
Source by using the belt clip.
l
The instrument is now ready for use.
Direct Plug-In Power Source
l
Plug Power cord from the
Binocular microscope into the
Direct Plug-In Power cord.
l
Push in until firmly in place.
l
Gently screw the external
connector sleeve clock-wise to secure (optional).
l
Plug direct power source into a nearby receptacle.
l
The instrument is now ready for use.
To instrument
10
Accessories
Pneumatic Speculum Holder
l
A pneumatic speculum holder with a
4x’s magnification lens can be used
to aid in examination of the ear.
Lamp Replacement
A
I
I
CAUTION: Lamps may become very HOT. Be
sure to allow lamps to cool before changing.
l
To change the lamp, flip the binocular assembly into its up position.
Remove the reflector assembly by placing the thumb on the
notch located on the bottom of the reflector housing and pushing
the reflector assembly. (Step 1)
Remove lamp and insert a new Welch
Allyn
lamp No. 08500 into
the back of the reflector. (Step 2)
Replace reflector housing into instrument and push until it snaps
into place.
NOTE: Reflector assembly air vents should be positioned top
and bottom.
Binocular assembly
Reflector
assembly
Step 1
Step 2
11
Cleaning
All glass surfaces, portable binocular microscope lenses, ocular or
eyepiece covers and lamp reflective covers can be cleaned with a
soft cloth moistened with alcohol.
The exterior surfaces of the portable binocular microscope and
power sources can be wiped clean with a soft cloth moistened
with alcohol.
NOTE: Avoid using harsh cleansing fluids or excessively
moistened cloths on any portion of the instrument.
Maintenance
Lamp replacement and cleaning may be performed by the user on
an as needed basis. Additional servicing should be performed by
returning the instrument to an authorized Welch
Allyn
Technical
Service Department or distributor. See “Service and Warranty
Information” section.
Specifications
In
terpupillary
Distance
49 mm to 74 mm
Light Source
3.60v,
Halogen
Headband Adjustment Range
Small, Medium and Large
Weight (No.
20500S)
80
g
Transport and Storage
-20°C to
40
o
C
95% RH maximum
Approvals
UL 544,
CAN/CSA
C22.2 No.125
IEC 601-1, IEC 601-l -2, CE
Product and Accessory Ordering Information
Product No.
Description
Instruments
No.
20500S
Spectacle
LumiView
with Portable Power Source
No. 20510S
Spectacle LumiView with Direct Plug-In
No. 20500H
Headband LumiView with Portable Power Source
No. 20510H
Headband LumiView with Direct Plug Power
No. 205308
No. 20530H
No.
20520S
Spectacle LumiView w/o Power source
Headband LumiView w/o Power source
Spectacle
Flat Surface Magnifier w/ Portable Power Headband
No. 20520H
1
Flat Surface Magnifier w/Portable Power Spectacle
No. 205408
1
Flat Surface Magnifier w/o Power Source
No. 20540H
1
Headband Flat Surface Magnifier
w/o
Power Source
I
Power Sources
No. 75260
No. 75265
No. 74180
Portable Power Source w/ charger
International Portable Power Source w/Charger
(specify country and voltage)
Charger
only for No. 75260
No. 74185
No. 75210
No. 75215
International Charger only for No. 75265
(specify country and voltage)
Direct Plug-In Power Source
International Direct Plug-In Power Source
(specify country and voltage)
Note: The power
source
options listed above operate with all
instrument configurations.
I
1
Accessories
I
No. 08500
Replacement lamp for device (all models)
No. 205007-501
Replacement Reflector Assembly
No. 72250
Replacement battery for portable battery pack
No. 21502
lnsufflation bulb system for LumiView models
No. 21505
Pneumatic Speculum Holder with specula for
LumiView models
No. 22002
Poly Speculum 2mm
No. 22003
Poly Speculum 3mm
No. 22004
Poly Speculum 4mm
No. 22005
Poly Speculum 5mm
No. 22009
Polv
Speculum
9mm
1
No. 05374
I
Hard case
Note:
Only
accessories
and
power
sources
indicated in this manual
are
to
be used with the
Portable
Binocular Microscope and Flat Surface Magnifier.
13
Portable Power Source
(Welch Allyn Model No. 75260)
This power source is designed for use in
both the office and the hospital and is
ideal for carrying to satellite offices. Power
On time is 90 minutes after a full charge of
10 hours.
Power Sources (Portable and Direct Plug-In)
Features:
2
1
1. On/Off Switch
2. Instrument Connector
3. Charging Transformer Port
Specifications:
Battery
Type
Voltage/Capacity
Charger
4.
Charging Indicator
5.
Belt Clip
6.
Spare Lamp Receptacle
Welch Allyn
#72250
(nickel-cadmium)
3.6
VDC/1.8
Ahr
Welch Allyn
#74180
(for international orders, specify country)
14
Connecting Instrument to Portable Power Source:
l
Plug instrument power
Portable Power
Source
cord into the power cord
connector port on top of the
power source.
l
Push in until firmly in place.
l
Gently screw the external
connector sleeve clockwise
to secure (optional).
Recharging the Portable Power Source:
l
Turn portable power source off.
l
Disconnect instrument from
power source.
On/Off
l
Plug charging transformer into
portable power source.
l
Plug charging transformer into
wall socket. LED light indicates
unit is charging.
l
Disconnect charging
transformer from power source
when fully charged, after
10-12 hours.
Accessing Spare Lamp
l
Lift the spare lamp out of
its receptacle and use.
15
Battery Replacement
l
Be sure power is off.
l
Remove both screws from back of power source with Phillips
head screwdriver.
l
Grasp the belt clip, gently pull back and down on the housing.
(Steps 2 and 3)
l
Lift battery out and unplug from unit.
l
Replace with new battery and reverse above steps.
Step 1
Step 3
Step 2
Step 4
NOTE: Power source housing
screws
must be securely tightened
in order to properly ho/d electrical components in place.
Direct Plug-In Transformer
l
Plug Power cord from the binocular otoscope into the Direct
Plug-In Power cord.
l
Push in until firmly in place.
l
Gently screw the external connector sleeve clockwise to
secure (optional).
l
The instrument is now ready for use.
l
Plug direct power source into a nearby receptacle.
e
To instrument
16
Service and Warranty Information
Service
For customers in North America, please return instruments requiring
service to a Welch Allyn Technical Service Department listed below or
to an authorized Welch Allyn distributor.
Technical
Service
Department
Welch Allyn, Inc.
4341 State Street Road
Skaneateles Falls, NY
13153-0200
U.S.A.
Telephone: 800-535-6663 (in U.S.A. only) or (315) 685-4560
Fax: 315-685-4653
For customers outside of North America, return your unit to a
local, authorized Welch Allyn distributor or to your nearest Welch
Allyn service center.
Warranty
Welch Allyn, Inc. warrants the Portable Binocular Microscope and
Flat Surface Magnifier to be free of original defects in material and
workmanship and to perform in accordance with manufacturer’s
specifications for a period of one year from the date of purchase.
If this instrument or any component thereof is found to be defective
or at variance with the manufacturer’s specifications during the
warranty period, Welch Allyn will repair or replace the instrument
or component(s) at no cost to the purchaser.
This warranty only applies to instruments purchased new from Welch
Allyn or its authorized distributors or representatives. The purchaser
must return the instrument directly to Welch Allyn or an authorized
distributor or representative and bear the costs of shipping.
This warranty does not cover breakage or failure due to tampering,
misuse, neglect, accidents, modification or shipping, and is void if
the instrument is not used in accordance with manufacturer’s
recommendations or if repaired or serviced by other than Welch Allyn
or a Welch Allyn authorized representative.
No other express or implied warranty is given.
17
Problem Solution
Illumination spot is too high
Make sure you are 14” to 16”
and is out of field of view.
from patient or object under
inspection. If you are too close,
the illumination spot will be
too high.
Make sure optical section is
aligned with user’s eyes. Sug-
gest looking into the instrument
when on user. The user’s eyes
should be centered vertically on
the center mirrors.
&
A. optical section
too high on user
-/-
B.
optical section
too low on user
d;i%
(
,T,
d
C. optical section
centered
cor-
‘-I
rectly
on user
To correct A and B, simply
loosen screw on back of optical
section and adjust optical
section up or down until image
is centered.
User encounters glare off of
the pneumatic insufflation
system.
Clean the glass section with
alcohol swab or clean cotton
cloth.
Rotate pneumatic assembly
until glare dissipates.
Troubleshooting Guide
18
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84

Welch Allyn LumiView Operating Instructions Manual

Tipo
Operating Instructions Manual

in altre lingue