Allen-Bradley SLC 5/05 Installation Instructions Manual

Publication 1747-IN009C-MU-P - December 2002

Installation Instructions

SLC 5/03™, SLC 5/04™, and SLC 5/05™

Modular Processors

(Catalog Numbers 1747-L531, 1747-L532,

1747-L541, 1747-L542, 1747-L543,

1747-L551, 1747-L552, 1747-L553

1747-L542P, 1747-L543P, 1747-L553P)

To Use Publication

Install your chassis

Installation du châssis

Installation des Chassis

Installazione dello chassis

Instalar el chasis

Instalar o chassi

1746-IN016A-MU-P

Install your power supply

Installation de l’alimentation

Installation des Netzteils

Installazione dell’alimentatore

Instalar la fuente de alimentación eléctrica

Instalar a fonte de energia

1746-IN004B-MU-P

Install your processor

Installation de processeur

Installation des Prozessors

Installazione del processore

Instalar el procesador

Instalar o processador

1747-IN009B-MU-P

English Section.................................... 3

Section en français ........................... 15

Deutscher Abschnitt.......................... 27

Sezione in Italiano............................. 39

Sección en español........................... 51

Seção em português ......................... 63

Allen-Bradley Parts

2

Publication 1747-IN009C-MU-P - December 2002

Installation Instructions

English Section

SLC 5/03™, SLC 5/04™, and SLC 5/05™ Modular

Processors

(Catalog Numbers 1747-L531, 1747-L532,

1747-L541, 1747-L542, 1747-L543,

1747-L551, 1747-L552, 1747-L553,

1747-L542P, 1747-L543P, 1747-L553P)

Inside…........................................................................................ page

Important User Information ................................................................. 4

For More Information........................................................................... 5

Required Tools and Equipment............................................................ 6

Safety Considerations.......................................................................... 6

Installation Procedure.......................................................................... 7

Troubleshooting ................................................................................. 11

Specifications .................................................................................... 11

Battery Handling, Storing, and Transporting (Cat. No. 1747-BA)...... 13

Allen-Bradley Parts

4 SLC 5/03™, SLC 5/04™, and SLC 5/05™ Modular Processors

Publication 1747-IN009C-MU-P - December 2002

Important User Information

Because of the variety of uses for the products described in this publication, those responsible

for the application and use of this control equipment must satisfy themselves that all

necessary steps have been taken to assure that each application and use meets all performance

and safety requirements, including any applicable laws, regulations, codes and standards.

The illustrations, charts, sample programs and layout examples shown in this guide are

intended solely for purposes of example. Since there are many variables and requirements

associated with any particular installation, Allen-Bradley does not assume responsibility or

liability (to include intellectual property liability) for actual use based upon the examples

shown in this publication.

Allen-Bradley publication SGI-1.1, Safety Guidelines for the Application, Installation, and

Maintenance of Solid-State Control (available from your local Allen-Bradley office), describes

some important differences between solid-state equipment and electromechanical devices

that should be taken into consideration when applying products such as those described in

this publication.

Reproduction of the contents of this copyrighted publication, in whole or in part, without

written permission of Allen-Bradley Company, Inc., is prohibited.

Throughout these installation instructions we use notes to make you aware of safety

considerations:

Attention statements help you to:

• identify a hazard

• avoid the hazard

• recognize the consequences

ATTENTION

!

Identifies information about practices or circumstances that can lead

to personal injury or death, property damage or economic loss.

IMPORTANT

Identifies information that is critical for successful application and

understanding of the product.

SLC 5/03™, SLC 5/04™, and SLC 5/05™ Modular Processors 5

Publication 1747-IN009C-MU-P - December 2002

For More Information

If you would like a manual, you can:

• download a free electronic version from the internet:

www.theautomationbookstore.com

• purchase a printed manual by:

– contacting your local distributor or Rockwell Automation representative

– visiting www.theautomationbookstore.com and placing your order

– calling 1.800.963.9548 (USA/Canada)

or 001.330.725.1574 (Outside USA/Canada)

For Refer to this Document Pub. No.

A more detailed description on how to

install and use your modular SLC 500

system.

SLC 500 Modular Hardware

Style User Manual

1747-UM011C

A reference manual that contains status

file data, instruction set, and

troubleshooting information.

SLC 500 Instruction Set

Reference Manual

1747-RM001C

Allen-Bradley Parts

6 SLC 5/03™, SLC 5/04™, and SLC 5/05™ Modular Processors

Publication 1747-IN009C-MU-P - December 2002

Required Tools and Equipment

• medium blade screwdriver

• programming equipment

• 1747-CP3 cable or appropriate network interface

Safety Considerations

For general recommendations concerning installation safety requirements and safety related

work practices, refer to the requirements specific to your region.

• Europe: Reference the standards found in EN 60204 and your national regulations.

• United States: refer to NFPA 70E, Electrical Safety Requirements for Employee Workplaces.

Network Interface SLC 5/03 SLC 5/04 SLC 5/05

1747-PIC X

1747-CP3 X X X

1747-KTX, -PKTX

X

(1)

requires 1784-CP14 cable

X

(3)

requires 1784-CP13 cable

1747-PCMK

X

(2)

requires 1784-PCM4 cable

X

(4)

requires 1784-PCM6 cable

10Base-T EtherNet X

ATTENTION

!

Never install, remove, or wire any module while power is applied.

Also, do not expose processor modules to surfaces or other areas that

may typically hold an electrostatic charge. Electrostatic charges can

alter or destroy memory.

IMPORTANT

See page 13 for information on proper battery handling, storage, and

transporting.

SLC 5/03™, SLC 5/04™, and SLC 5/05™ Modular Processors 7

Publication 1747-IN009C-MU-P - December 2002

Installation Procedure

Install the Processor

Make sure system power is off; then insert the processor into slot 0 of the 1746 chassis.

Apply Power to the Processor

1. Energize the chassis power supply.

2. Check the chassis power supply and processor LEDs. The power LED on the power

supply should be on and the fault LED on the processor should be flashing. See the

figure on page 8 for location of the power supply and processor LEDs.

IMPORTANT

The SLC 500 modular processors must be inserted into the left slot

(slot 0), as shown below. In addition, remove the protective wrap after

installing the processor.

Power Supply

Protective Wrap

Card Guide

Processor Release

Allen-Bradley Parts

8 SLC 5/03™, SLC 5/04™, and SLC 5/05™ Modular Processors

Publication 1747-IN009C-MU-P - December 2002

Load Your Software

Refer to your programming software documentation.

Establish Communication to the Processor

1. Refer to the following table to establish communication between the processor and

your personal computer.

Processor: Procedure:

SLC 5/03 Connect 1747-PIC from the processor to your personal computer serial port or use a

1784-KTX, -PKTX, or -PCMK interface, or a 1747-CP3 cable from channel 0 of the

processor to the personal computer serial port.

SLC 5/04 Connect a 1747-CP3 cable from channel 0 of the processor to the personal computer

serial port or use a 1784-KTX, -PKTX, or -PCMK interface.

SLC 5/05 Connect a 1747-CP3 cable from channel 0 of the processor to the personal computer

serial port. For Ethernet connection, connect channel 1 of the processor and the PC

Ethernet Card to an Ethernet hub using 10Base-T compatible cable.

(1)

Ethernet IP address must first be set via BOOTP or an RS-232 connection.

POWER

RUN

FLT

BATT

FORCE

DH485

RS232

POWER

RUN

FLT

BATT

FORCE

DH+

RS232

POWER

RUN

FLT

BATT

FORCE

ENET

RS232

Power Supply and LED Indicators

Indicates the LED is OFF

Indicates the LED is ON

Indicates the LED is FLASHING

Status of LED does not matter

SLC 5/05

SLC 5/04

SLC 5/03

SLC 5/03™, SLC 5/04™, and SLC 5/05™ Modular Processors 9

Publication 1747-IN009C-MU-P - December 2002

2. Set the communication parameters of the software to match the default parameters of

the processor:

Replacing the Battery

Your SLC processor provides back-up power for RAM through a replaceable lithium battery.

This battery provides back-up for approximately 2 years. The BATT LED on the front of the

processor alerts you when the battery voltage has fallen below a threshold level.

To replace the lithium battery follow these steps:

1. Remove power from the SLC 500 power supply.

2. Remove the processor from the chassis by pressing the retainer clips at both the top

and bottom of the module and slide it out.

Channel 0 Configuration Channel 1 Configuration

SLC 5/03, 5/04, 5/05 SLC 5/03 SLC 5/04 SLC 5/05

DF1 Full-Duplex:

• no handshaking

• 19.2K baud

• CRC Error Check

• duplicate detect on

• no parity

DH-485:

• 19.2K baud

• node address = 1

DH+™:

• 57.6K baud

• node address = 1

Ethernet

• BOOTP

enabled

ATTENTION

!

Do not remove the processor from the SLC 500 chassis until all

power is removed from the SLC 500 power supply

ATTENTION

!

Do not expose the processor to surfaces or other areas that may

typically hold an electrostatic charge. Electrostatic charges can alter or

destroy memory.

Allen-Bradley Parts

10 SLC 5/03™, SLC 5/04™, and SLC 5/05™ Modular Processors

Publication 1747-IN009C-MU-P - December 2002

3. Unplug the battery connector. Refer to the figure on page 10 for battery connector

location.

4. Remove the battery from the retaining clips.

5. Insert a new battery into the battery retaining clips.

6. Plug the battery connector into the socket as shown above.

7. Re-insert the module into the SLC 500 chassis.

8. Restore power to the SLC 500 power supply.

9. Close the processor door.

IMPORTANT

The SLC 5/03, 5/04, and 5/05 processors have a capacitor that

provides at least 30 minutes of battery back-up while the battery is

disconnected. Data in RAM is not lost if the battery is replaced within

30 minutes

IMPORTANT

See page 13 for information on proper battery handling, storage, and

transporting.

White

Red

Battery Connector

Left Side View

Battery

SLC 5/03™, SLC 5/04™, and SLC 5/05™ Modular Processors 11

Publication 1747-IN009C-MU-P - December 2002

Troubleshooting

Before troubleshooting your SLC 500 system, please obtain an SLC 500 Modular Hardware

Style User Manual (1747-UM011) from one of the sources listed on page 5. Refer to the

chapter on Troubleshooting.

In addition to the SLC 500 Modular Hardware Style User Manual, the SLC 500 Instruction

Set Reference Manual (1747-RM001) may also be obtained from the sources listed on page 5.

This manual contains explanations and examples for the entire instruction set as well as for all

status words and bits. It also contains explanations for all possible fault codes found in status

word S:6.

Specifications

Operating Specifications

Specification for

1747-

SLC 5/03 SLC 5/04 SLC 5/05

L531 L532 L541 L542 L543 L551 L552 L553

Memory (words) 8K 16K 16K 32K 64K 16K 32K 64K

Maximum I/O Capacity 4096 discrete inputs / 4096 discrete outputs

Max. Local System 3 chassis / 30 slots

Programming

Instructions

99

Typical Scan Time

(1)

The scan times are typical for a 1K ladder logic program consisting of simple ladder logic and communication servicing.

Actual scan times depend on your program size, instructions used, and the communication protocol.

1 ms/K 0.9 ms/K

Bit Execution (XIC) 0.44 µs 0.37 µs

Programming Software SLC 5/03s and SLC 5/04s: RSLogix 500™, PLC-500 A.I. Series™,

SLC 5/05s: RSLogix 500™

Allen-Bradley Parts

12 SLC 5/03™, SLC 5/04™, and SLC 5/05™ Modular Processors

Publication 1747-IN009C-MU-P - December 2002

Communication

Communication options for the SLC 5/03, 5/04, and 5/05 processors are as follows:

• DH485

• RS-232 protocols

(DF1 Full-Duplex, DF1 Half-Duplex “master/slave”, DF1 Radio Modem, DH-485,

or ASCII)

• Data Highway Plus™

(A 1785-KA5P is required for the SLC 5/03 and SLC 5/05 processors.)

• Ethernet TCP/IP

(A 1761-NET-ENI is required for the SLC 5/03 and SLC 5/04 processors)

• ControlNet (via a 1747-KFC15)

• DeviceNet (via a 1761-NET-DNI)

General Specifications

Description Specification

Power Supply Loading at 5V dc 500 mA for the SLC 5/03 processor

1.0 A for the SLC 5/04 and 5/05 processors

Power Supply Loading at 24V dc 175 mA for the SLC 5/03 processor

0 mA for the SLC 5/04 processor

(1)

SLC 5/04 Processors manufactured prior to April 2002 draw 200 mA at 24V dc. Check your label to verify your processor’s

current draw.

0 mA for the SLC 5/05 processor

Program Scan Hold-up Time after Loss of

Power

20 ms to 3 s (dependent on power supply loading)

Noise Immunity NEMA Standard ICS 2-230

Vibration Displacement: 0.015 inch, peak-to-peak at 5-57 Hz

Acceleration: 2.5Gs at 57-2000 Hz

Shock (operating) 30Gs

Ambient Temperature Rating Operating: 0 to +60°C (+32°F to +140°F)

Storage: 40°C to +85°C (-40°F to +185°F)

Humidity 5 to 95% without condensation

Agency Certification UL listed

CSA approved

Class 1, Groups A, B, C or D, Division 2

CE compliant for all applicable directives

C-Tick marked for all applicable acts

SLC 5/03™, SLC 5/04™, and SLC 5/05™ Modular Processors 13

Publication 1747-IN009C-MU-P - December 2002

Memory Back Up

The following table shows the memory back up options for the SLC 5/03, 5/04, and 5/05

processors. Flash EPROMs (Flash Erasable Programmable Read Only Memory) combine the

versatility of EEPROMs (Electrically-Erasable Programmable Read Only Memory) with the

security of UVPROMs (UV-Erasable PROM).

Battery Handling, Storing, and Transporting (Cat. No. 1747-BA)

Handling

Storing

Store the lithium batteries in a cool, dry environment, typically +20°C to +25°C (+68°F to

+77°F) and 40% to 60% relative humidity.

Transporting

One or Two Batteries - Up to two batteries can be shipped together within the United States

without restriction. Regulations governing shipment to or within other countries may differ.

Three or More Batteries - Procedures for the transportation of three or more batteries

shipped together within the United States are specified by the Department of Transportation

(DOT) in the Code of Federal Regulations, CFR49, “Transportation.” An exemption to these

regulations, DOT - E7052, covers the transport of certain hazardous materials classified as

flammable solids. This exemption authorizes transport of lithium batteries by motor vehicle,

rail freight, cargo vessel, and cargo-only aircraft, providing certain conditions are met.

Transport by passenger aircraft is not permitted.

Memory Back

Up Option

SLC 5/03

(1747-L531,-L532)

SLC 5/04

(1747-L541, -542, -543)

SLC 5/05

(1747-L551, -552, -553)

Flash EPROM 1747-M13

(OS302 Series C or higher)

1747-M13

(OS401 Series C or higher)

1747-M13

(OS501 Series C or higher)

ATTENTION

!

Do not charge the batteries. An explosion could result or the cells

could overheat causing burns. Do not open, puncture, crush, or

otherwise mutilate the batteries. An explosion may result and/or

toxic, corrosive, and flammable liquids would be exposed

Allen-Bradley Parts

14 SLC 5/03™, SLC 5/04™, and SLC 5/05™ Modular Processors

Publication 1747-IN009C-MU-P - December 2002

Shipment of depleted batteries for disposal may be subject to specific regulation of the

countries involved or to regulations endorsed by those countries, such as the IATA Restricted

Articles Regulations of the International Air Transport Association, Geneva, Switzerland.

For disposal, batteries must be packaged and shipped in accordance with transportation

regulations, to a proper disposal site. The U.S. Department of Transportation authorizes

shipment of “Lithium batteries for disposal” by motor vehicle only in regulation 173.1015 of

CFR 49 (effective January 5, 1983). For additional information contact:

U.S. Department of Transportation

Research and Special Programs Administration

400 Seventh Street, S.W.

Washington, D.C. 20590

Although the Environmental Protection Agency at this time has no regulations specific to

lithium batteries, the material contained may be considered toxic, reactive, or corrosive. The

person disposing of the material is responsible for any hazard created in doing so. State and

local regulations may exist regarding the disposal of these materials.

For a lithium battery material safety data sheet, contact the manufacturer:

IMPORTANT

Regulations for transportation of lithium batteries are periodically

revised.

ATTENTION

!

Do not incinerate or dispose of lithium batteries in general trash

collection. Explosion or violent rupture is possible. Batteries should

be collected for disposal in a manner to prevent against short

circuiting, compacting, or destruction of case integrity and hermetic

seal.

Sanyo Energy Corporation

600 Supreme Drive

Bensenville, IL 60106

USA

Tadarand Electronics

2 Seaview Blvd.

Port Washington, NY 11050

USA

or

Publication 1747-IN009C-MU-P - Décembre 2002

Notice d’installation

Section en français

Processeurs modulaires SLC 5/03™,

SLC 5/04™ et SLC 5/05™

(Références 1747-L531 1747-L532,

1747-L541, 1747-L542, 1747-L543,

1747-L551, 1747-L552, 1747-L553,

1747-L542P, 1747-L543P, 1747-L553P)

Contenu….................................................................................... page

Informations importantes destinées à l’utilisateur........................... 16

Complément d’informations .............................................................. 17

Outils et équipement requis .............................................................. 18

Consignes de sécurité........................................................................ 18

Procédure d’installation..................................................................... 19

Dépannage......................................................................................... 23

Caractéristiques................................................................................. 23

Manipulation, stockage et transport des piles (réf. 1747-BA).......... 25

Allen-Bradley Parts

16

Publication 1747-IN009C-MU-P - Décembre 2002

Informations importantes destinées à l’utilisateur

En raison de la diversité des utilisations des produits décrits dans le présent manuel, les

personnes responsables de l’équipement doivent s’assurer que toutes les mesures ont été

prises pour que l’application et l’utilisation des produits soient conformes aux exigences de

performance et de sécurité, ainsi qu’aux lois, règlements, codes et normes en vigueur.

Les illustrations, schémas et exemples de programmes contenus dans ce manuel sont

présentés à titre indicatif seulement. En raison du nombre important de variables et

d’impératifs associés à chaque installation, la société Allen-Bradley ne saurait être tenue pour

responsable ni être redevable (y compris en matière de propriété intellectuelle) des suites

d’utilisation réelle basée sur les exemples et schémas présentés dans ce manuel.

La publication SGI-1.1, « Safety Guidelines for the Application, Installation, and Maintenance of

Solid-State Control » (disponible auprès de votre agence commerciale Allen-Bradley), décrit

certaines différences importantes entre les équipements électroniques et les équipements

électromécaniques qui devront être prises en compte lors de l’application de ces produits

comme indiqué dans la présente publication.

Toute reproduction partielle ou totale du présent manuel sans autorisation écrite de la société

Allen-Bradley est interdite.

Des remarques sont utilisées tout au long de ce manuel pour attirer votre attention sur les

mesures de sécurité à prendre en compte :

Les messages « Attention » vous aident à :

• identifier un danger ;

• éviter un danger ;

• en discerner les conséquences.

ATTENTION

!

Actions ou situations risquant d’entraîner des blessures pouvant être

mortelles, des dégàts matérials ou des pertes financières.

IMPORTANT

Informations particulièrement importantes dans le cadre de l’utilisation

du produit.

17

Publication 1747-IN009C-MU-P - Décembre 2002

Complément d’informations

Pour vous procurer un manuel, vous pouvez :

• le charger gratuitement depuis le site Internet :

www.theautomationbookstore.com

• acheter un manuel imprimé. Pour cela :

– contactez votre distributeur local Rockwell Automation

– allez sur le site www.theautomationbookstore.com puis commandez le

manuel en ligne

– appelez le 001.800.963.9548 (Etats-Unis/Canada)

ou le 001.330.725.1574 (hors Etats-Unis/Canada)

Pour Voir à ce document Référence

Une description détaillée de l’installation et

de l’utilisation de votre système SLC 500

modulaire.

SLC 500 Modular hardware

Style Installation and

Operation Manual

(disponible en anglais

uniquement)

1747-UM011C

Un manuel de référence comportant des

informations sur les données du fichier

d’état, le jeu d’instructions et le dépannage.

SLC 500 Instrument Set

Reference Manual

(disponible en anglais

uniquement)

1747-RM001C

Allen-Bradley Parts

18

Publication 1747-IN009C-MU-P - Décembre 2002

Outils et équipement requis

• un tournevis plat de taille moyenne

• un équipement de programmation

• un câble 1747-CP3 ou une interface réseau appropriée

Consignes de sécurité

Pour connaître les recommandations générales relatives aux impératifs de sécurité

d’installation et de protection des postes de travail, reportez–vous aux normes en vigueur

dans votre région.

• Europe : reportez-vous aux normes EN 60204 et aux réglementations nationales.

• Etats-Unis : reportez-vous au NFPA 70E, « Electrical Safety Requirements for Employee

Workplaces ».

Interface réseau SLC 5/03 SLC 5/04 SLC 5/05

1747-PIC X

1747-CP3 X X X

1747-KTX, -PKTX

X

(1)

(1) câble 1784-CP14 requis

X

(3)

(3) câble 1784-CP13 requis

1747-PCMK

X

(2)

(2) câble 1784-PCM4 requis

X

(4)

(4) câble 1784-PCM6 requis

10Base-T EtherNet X

ATTENTION

!

Ne jamais installer, retirer ou câbler un module sous tension.

N’exposez pas les modules processeurs à des surfaces ou autres zones

généralement chargées en électricité statique. Les charges

électrostatiques peuvent endommager voire détruire la mémoire.

IMPORTANT

Pour plus d’informations sur la manipulation, le stockage et le transport

des piles, reportez-vous à la page 25.

19

Publication 1747-IN009C-MU-P - Décembre 2002

Procédure d’installation

Installation du processeur

Assurez-vous que l’alimentation est hors tension, puis insérez le processeur dans

l’emplacement 0 du châssis 1746.

Mise sous tension du processeur

1. Mettez l’alimentation du châssis sous tension.

2. Surveillez les voyants du processeur et d’alimentation du châssis. Le voyant

d’alimentation doit être allumé et le voyant d’erreur du processeur doit clignoter.

Reportez-vous à la figure page 20 pour connaître l’emplacement des voyants du

processeur et d’alimentation du châssis.

IMPORTANT

Les processeurs modulaires SLC 500™ doivent être insérés dans

l’emplacement de gauche (emplacement 0), comme illustré ci-dessous.

Retirez la bande de protection après avoir installé le processeur.

Alimentation

Bande de protection

Guide-carte

Loquet de

verrouillage du

processeur

Allen-Bradley Parts

20

Publication 1747-IN009C-MU-P - Décembre 2002

Chargement de votre logiciel

Consultez la documentation de votre logiciel de programmation.

Etablissement des communications avec le processeur

1. Reportez-vous au tableau suivant pour établir la communication entre le processeur et

votre ordinateur.

Processeur Procédure

SLC 5/03 Connectez le 1747-PIC du processeur au port série de votre ordinateur ou utilisez une

interface 1784-KTX, -PKTX ou -PCMK, ou un câble 1747-CP3 du canal 0 du processeur au

port série de votre ordinateur.

SLC 5/04 Connectez un câble 1747-CP3 du canal 0 du processeur au port série de votre ordinateur

ou utilisez une interface 1784-KTX, -PKTX ou -PCMK.

SLC 5/05 Connectez un câble 1747-CP3 du canal 0 du processeur au port série de votre ordinateur.

Pour une connexion Ethernet, connectez le canal 1 du processeur et la carte Ethernet PC

à un hub Ethernet à l'aide d'un câble 10Base-T.

(1)

(1) L'adresse IP Ethernet doit d'abord être définie par BOOTP ou une connexion RS-232.

POWER

RUN

FLT

BATT

FORCE

DH485

RS232

POWER

RUN

FLT

BATT

FORCE

DH+

RS232

POWER

RUN

FLT

BATT

FORCE

ENET

RS232

Indique que le voyant est éteint.

Indique que le voyant est allumé.

Indique que le voyant clignote.

L’état du voyant n’a pas d’importance.

SLC 5/03

SLC 5/05

SLC 5/03

Voyants

La pagina sta caricando ...

Allen-Bradley SLC 5/05 Installation Instructions Manual

Questo manuale è adatto anche per

Allen-Bradley SLC 5/05 Installation Instructions Manual

in altre lingue

Documenti correlati

Altri documenti