Electrolux EWF1090 Manuale utente

Categoria
Lavatrici
Tipo
Manuale utente
VIET
WASHING MACHINE
EWF 1090
INSTRUCTION BOOKLET
147 103 110
GB
TH
ID
im_ewf1090_eu.qxd 05/09/2005 17:11 Pagina 1
The symbols you will see on some paragraphs of this booklet have the following meaning:
The warning triangle and/or the key words (Warning!, Caution!) emphasize information that is particularly
important for your safety or correct functioning of the appliance.
The information marked with this symbol provides additional instructions and practical tips on the use of
the appliance.
Tips and information about economical and ecological use of the machine are marked with this symbol.
Our contribution to the protection of the
environment: we use environmentally
friendly paper.
2
Dear customer,
Please read these operating instructions carefully
and pay particular attention to the safety notes
indicated in the first pages. We recommend that you
keep this instruction booklet for future reference and
pass it on to any future owners.
Sorting the laundry 12
Temperatures 12
Before loading the laundry 12
Maximum loads 12
Laundry weights 12
Removing stains 12
Detergents and additives 13
Quantity of detergents to be used 13
Internationnal wash code symbols 14
Operating sequence 15-17
Washing programmes 18-19
Maintenance 20
Bodywork 20
Door Seal 20
Detergent dispenser drawer 20
Drain pump 20
Water inlet filter 21
Emergency emptying out 21
Frost precautions 21
Something not working? 22-23
Warnings 3
Disposal 4
Tips for environmental protection 4
Technical specifications 4
Installation 5
Unpacking 5
Positioning 5
Water inlet 5
Water drainage 6
Electrical connection 6
Your new washing machine 7
Description of the appliance 7
Detergent dispenser drawer 7
Use 8
Control panel 8
Controls 8-11
Washing hints 12
Contents
Transport damages
When unpacking the appliance, check that it is not
damaged. If in doubt, do not use it and contact
the Service Centre.
im_ewf1090_eu.qxd 05/09/2005 17:11 Pagina 2
ENGLISH
3
Installation
All internal packing must be removed before using
the appliance. Serious damage may be caused to
the machine or adjacent furniture if the protective
transit devices are not removed or are not
completely removed. Refer to the relevant
paragraph in the instruction book.
Any electrical work required to install this
appliance must be carried out by a qualified
electrician.
Any plumbing work required to install this
appliance must be carried out by a qualified
plumber.
After having installed the machine, check that it is
not standing on its electrical supply cable.
If the appliance is placed on a carpeted floor,
ensure that air can circulate freely between the
feet and the floor.
Use
This appliance is designed for domestic use. It
must not be used for purposes other than those
for which it was designed.
Only wash fabrics which are designed to be
machine washed. Follow the instructions on each
garment label.
Do not overload the appliance. Follow the
instructions in the instruction book.
Make sure that all pockets are empty. Objects
such as coins, safety pins, pins and screws can
cause extensive damage.
Do not machine wash garments saturated with
petroleum, methylated spirits, trichlorethylene, etc.
If such fluids have been used to remove stains
prior to washing, wait until they have completely
evaporated from the fabric before placing
garments in the appliance.
Place small items such as socks, belts, etc. in a
cloth bag or pillowcase to prevent them getting
trapped between the drum and the tub.
Warnings
Use only the recommended quantities of fabric
softener. An excessive amount could damage the
laundry.
Leave the porthole door slightly ajar when the
appliance is not in use. This preserves the door
seal and prevents the formation of musty smells.
Always check that water has emptied out before
opening the door. If not, drain the water following
the instructions in the instruction book.
Always unplug the appliance and shut the water
tap after use.
General safety
Repairs to the machine must be carried out only by
qualified personnel. Repairs carried out by
inexperienced persons could cause serious
danger. Contact your local Service Centre.
Never pull the power supply cable to remove the
plug from the socket; always take hold of the plug
itself.
During high temperature wash programmes the
door glass may get hot. Do not touch it!
Child safety
Children are often not aware of how dangerous
electrical appliances can be. When the machine is
working, children should be carefully supervised
and not be allowed to play with the appliance.
The packaging components (e.g. plastic film,
polystyrene) can be dangerous to children - danger
of suffocation! Keep them out of childrens reach.
Keep all detergents in a safe place out of childrens
reach.
When the appliance is to be scrapped, cut off the
electrical supply cable and destroy the plug with
the remaining cable. Disable the door catch in
order to prevent children from becoming trapped
inside while playing.
The following warnings are provided in the interests of overall safety. You must read them carefully
before installing or using the appliance.
im_ewf1090_eu.qxd 05/09/2005 17:11 Pagina 3
4
Disposal
Tips for environmental protection
Packaging materials
The materials marked with the symbol are
recyclable.
>PE<=polyethylene
>PS<=polystyrene
>PP<=polypropylene
This means that they can be recycled by disposing of
them properly in appropriate collection containers.
Machine
Use authorised disposal sites for your old appliance.
Help to keep your country tidy!
To save water, energy and to help protect the
environment, we recommend that you follow these
tips:
Normally soiled laundry may be washed without
prewashing in order to save detergent, water and
time (the environment is protected too!).
The machine works more economically if it is fully
loaded.
With adequate pre-treatment, stains and limited
soiling can be removed; the laundry can then be
washed at a lower temperature.
Measure out detergent according to the water
hardness, the degree of soiling and the quantity of
laundry being washed.
Technical specifications
DIMENSIONS
Height 85 cm
Width 60 cm
Depth 60 cm
MAXIMUM LOAD Cotton 8 kg
Synthetics 3.5 kg
Delicates 3.5 kg
Woollens 2 kg
Handwash 2 kg
Silk 1 kg
SPIN SPEED max 1000 rpm
POWER SUPPLY VOLTAGE/FREQUANCY 220-240V / 50HZ
TOTAL POWER ABSORBED 2200W
MINIMUM FUSE PROTECTION 10A
WATER PRESSURE Minimum 50kPa
Maximum 800kPa
This appliance complies with the following EEC Directives:
73/23/EEC of 19/02/73 relating to low voltage
89/336/EEC of 03/05/89 relating to electromagnetic compatibility.
im_ewf1090_eu.qxd 05/09/2005 17:11 Pagina 4
ENGLISH
5
Unpacking
All transit bolts and packing must be
removed before using the appliance.
You are advised to keep all transit devices so that they
can be refitted if the machine ever has to be transported
again.
1. Using a spanner, unscrew and remove the two
rear bottom screws. Slide out the two plastic pins.
Lay the machine on its back, taking care not to
squash the hoses. This can be avoided by placing
one of the corner packing pieces between the
machine and the floor
2. Remove the polystyrene block(s) from the bottom
of the machine and release the two plastic bags.
3. Very carefully slide out the left polythene bag,
removing it towards the right and then
downwards.
4. Very carefully slide out the right polythene bag,
removing it towards the left and then upwards.
Remove the bottom cover placed into the drum of
your appliance, lay its hook as the arrow A
indicates and push the top of the cover to seal it
closed
Important: You can find more detailed instructions
regarding the bottom cover assembling in its relative
bag.
5. Set the machine upright and remove the
remaining rear screw. Slide out the relevant pin.
6. Plug all the holes with the plugs which you will
find in the envolope containing the instruction
manual.
Positioning
Install the machine on a flat hard floor.
Make sure that air circulation around the machine
is not impeded by carpets, rugs etc. Check that
the machine does not touch the wall or cupboard
units. Carefully level by screwing the adjustable
feet in or out. Never place cardboard, wood or
similar materials under the machine to
compensate for any unevenness in the floor.
Water inlet
Connect the water inlet hose to a tap with 3/4 BSP
thread.
Use the hose supplied with the washing machine.
DO NOT USE OLD HOSES.
The other end of the inlet hose which connects to the
machine can be turned in any direction.
Simply loosen the fitting, rotate the hose and
retighten the fitting, making sure there are
no water leaks.
P1051
Installation
P1128
P0002
P1088
P1129
P0001
P1123
2
3
1
P1126
P1127
P0021
im_ewf1090_eu.qxd 05/09/2005 17:11 Pagina 5
6
The inlet hose must not be lengthened. If it is too
short and you do not wish to move the tap, you will
have to purchase a new, longer hose specially
designed for this type of use.
Water drainage
The end of the drain hose can be positioned in three
ways:
Hooked over the edge of a sink using the plastic
hose guide supplied with the machine. In this
case, make sure the end cannot come unhooked
when the machine is emptying.
This could be done by tying it to the tap with a piece
of string or attaching it to the wall.
In a sink drain pipe branch. This branch must be
above the trap so that the bend is at least 60 cm
above the ground.
Directly into a drain pipe at a height of not less
than 60 cm and not more than 90 cm.
The end of the drain hose must always be
ventilated, i.e. the inside diameter of the drain pipe
must be larger than the outside diameter of the drain
hose.
The drain hose must not be kinked. Run it along the
floor; only the part near the drainage point must be
raised.
For the correct functioning of the machine the
drain hose must remain hooked on the proper
support piece situated on the top part of back
side of the a[ppliance
P0023
P0022
Electrical connection
This machine is designed to operate on a 220-240 V,
single-phase, 50 Hz supply.
Check that your domestic electrical installation can
take the maximum load required (2.2 kW), also
taking into account any other appliances in use.
Connect the machine to an earthed socket.
The manufacturer declines any responsibility
for damage or injury through failure to comply
with the above safety precaution.
Should the appliance power supply cable
need to be replaced, this must be carried out
by our Service Centre.
Important!
When the appliance is installed the power supply
cable must be easily accessible.
im_ewf1090_eu.qxd 05/09/2005 17:11 Pagina 6
ENGLISH
7
1. Detergent dispenser drawer
2. Control panel
3. Door handle
4. Drain pump
5. Adjustable feet
Detergent dispenser drawer
Pre-wash
Main wash
Fabric softener, starch
Your new washing machine
Description of the appliance
12
4
3
5
This new machine, which is fitted with the New Jet System, meets all modern requirements for effective
treatment of laundry with low water, energy and detergent consumption.
The special Handwash programme with its new delicate wash system treats your delicate items with
extreme care.
The special wool programme with its new delicate wash system treats your woollens with extreme care.
The automatic cooling of the washing water from 90° to 60°C before draining will prevent old drain pipes
from being deformed.
The balance control device ensures the machine is stable during the spin.
im_ewf1090_eu.qxd 05/09/2005 17:11 Pagina 7
8
Use
Control panel
1. Detergent Dispenser Drawer
2. Programme selector dial
The programme selector dial is divided into 3sectios:
1. Cotton, Cotton Eco, Daily Cotton (Green section)
2. Jeans, Synthetics, Easy iron, Delicates, Wool,
Silk, Hand Wash, Quick30 (Blue section)
3. Drain, Rinse & Spin, Spin, Delicate Spin
(grey section)
The selector dial can be turned eighter clockwise or
anti-clockwise. Position Daily Cotton corresponds
to an energy saving programme for cotton and to
Off  to reset programme or switching OFF the
machine. At the end of programme, the selector dial
must be turned to position Off  to switch the
machine OFF.
3. Temperature button “Temp.”
Press this button repeatedly to increase or decrease
the temperature, if you want your laundry to be
washed at a temperature different from the one
proposed by the washing machine.
Maximum temperatures are 90°C for cotton, 60°C for
synthetic fabrics, 40°C for delicate fabrics, wool and
fabrics to be hand-washed, 30°C for silk and Quick
30 programme.
4. Spin Speed button “Spin”
Press this button repeatedly to change the spin
speed, if you want your laundry to be spin at a speed
different from the one proposed by the washing
machine and the relevent LED will light up.
Maximum speeds for EWF 1090 are:
for cotton: 1000 rpm
for wool, synthetic and handwashed fabrics 900 rpm.
for delicate, silk fabrics and mini programme: 700 rpm
By pressing the Spin speed button you can also
choose No Spin option.
No Spin option : when you choose this option,
the machine will drain the water of the last rinse, and
eliment the spin phase.To spin the Laundry, select
spin or delicate spin programme.
Select the desired spin speed by pressing this button
and press Start/ Add Clothes button.
123 4 5 6 8 97
im_ewf1090_eu.qxd 05/09/2005 17:11 Pagina 8
ENGLISH
9
5. Options Button
Depending on the programme, different functions can
be combined. These must be selected after choosing
the desired programme and before pressing the Start/
Add Clothes button.
When these buttons are pressed, the corresponding
LED will light up. When they are pressed again, the
corresponding LED goes out.
If an incorrect option is selected, the LED flashes for
about 2 seconds and the message Err is displayed.
Press these buttons to select the following options:
1. Prewash: Select this option if you wish your
laundry to be prewashed before the main wash
(not available for wool, handwash, mini programme
and silk programmes.)
The Prewash ends with a short spin at 650 rpm in
programmes for cotton and synthetic fabrics,
whereas in the programme for delicate fabrics the
water is only drained.
2. Extra Rinse: This option can be selected with all
programmes, except the wool and handwash
programme. The machine will add 2 rinses for
cottons and 1 rinse for synthetics, delicates and silk
programme.This option is recommended for people
who are allergic to detergents, and in areas where
the water is very soft.
3. Easy Iron: Selecting this option the laundry is
gently washed and spun to avoid any creasing
in this way ironing is easier.
4. Time Save: This option can be used for lightly
soiled (not for wool, hand wash, silk and
miniprogramme) in order to obtain a good washing
programme in a short time. The washing time will
be reduced according to the type of fabric and the
selected temperature.
6. Delay start Button
The wash programme can be delayed from 30 min -
60 min - 90 min, 2 hours and then by 1 hour up to a
maximum of 23 hours by means of this button.
Selecting the Delay Start
Select the programme and the required options.
Select the delay start.
Press Start / Add Clothes button: the machine
starts its hourly countdown.
The programme will start after the selected delay has
expired.
Delay Start cannot be used with Drain, Spin or
Delicate spin
.
Cancelling the delayed start
Press Start / Add Clothes button.
Press Start / Add Clothes button until 0 is
displayed.
Press Start / Add Clothes button again.
im_ewf1090_eu.qxd 05/09/2005 17:11 Pagina 9
10
7. Display
The display shows the following information:
Duration of the programme - Delayed start -
Incorrect option selection - Alarm code - End of
programme.
After selecting a programme, the duration is
displayed in hours and minutes ( for example 2.05).
The duration is calculated automatically on the basis of
the maximum recommended load for each type of fabric.
After the programme has started, the time remaining
is updated every minute
The selected delay (23 hours max) set by means of
the relevant button appears on the display for 3
seconds, then the duration of the previously selected
programme is displayed.
The countdown is updated every hour and for the last
2 hours it is updated for each 30 min.
Delayed start
Duration of the selected programme
If an option which is not compatible with the set wash
programme is selected, the message Err is displayed
for 2 seconds.
In the event of operating problems, some alarm
codes can be displayed, for example E20 (see
paragraph Something not working).
When the programme has finished a flashing zero is
displayed.
End of programme
Alarm codes
Incorrect option selection
im_ewf1090_eu.qxd 05/09/2005 17:11 Pagina 10
ENGLISH
11
8. Start/ Add Clothes Button
This button has 2 functions:
Start:
after you have selected the desired programme and
options, press this button to start the washing
machine. The light close to the button will stop
flashing and remain lit.If you have selected a delay
time option, the countdown will begin and will be
shown on the display.
Add Clothes:
When you press this button again, the programme in
progress is interrupted. The light close to the button
will start flashing. To restart the programme, press
the button again. When you press Add Clothes, it
becomes possible to open the door if:
The washing machine is not in the heating phase;
The level of the water is not high;
The drum is not turning.
Important! You must pause the washing machine
before you make any change in the programme in
progress, by pressing START/ Add Clothes button.
9. Programme Phase indicator
Light
By selecting the wash programme, the LED
corresponding to the various phases making up the
programme lights.
After you have started the programme, only the LED
relevant to the phase that is currently being carried
out will remain lit.
At the end of the programme the End LED
illuminates.
The End LED flashes in the event of operating
problems. And the relative alarm code appears on
the display.
E10 = the machine does not fill
E20 = the machine does not empty
E40 = the door has not been closed
To eliminate the problem, see paragraph Something
not working.
im_ewf1090_eu.qxd 05/09/2005 17:11 Pagina 11
Washing hints
Sorting the laundry
Follow the wash code symbols on each garment
label and the manufacturers washing instructions.
Sort the laundry as follows:
whites, coloureds, synthetics, delicates, woollens.
Temperatures
90
o
-95
o
for normally soiled white cottons and linen
(e.g. tea cloths, towels, tablecloths,
sheets...)
50
o
-60
o
for normally soiled, colour fast garments
(e.g. shirts, night dresses, pyjamas....) in
linen, cotton or synthetic fibres and for
lightly soiled white cotton (e.g.
underwear).
O
(cold) for delicate items (e.g. net curtains),
mixed
30
o
-40
o
laundry including synthetic fibres and
woollens bearing the label «pure new
wool, machine washable, non-shrink».
Before loading the laundry
Never wash whites and coloureds together. Whites
may lose their whiteness in the wash.
New coloured items may run in the first wash; they
should therefore be washed separately the first time.
Make sure that no metal objects are left in the
laundry (e.g. hair clips, safety pins, pins).
Button up pillowcases, close zip fasteners, hooks
and poppers. Tie any belts or long tapes.
Remove persistent stains before washing. Rub
particularly soiled areas with a special detergent or
detergent paste.
Treat curtains with special care. Remove hooks or tie
them up in a bag or net.
Maximum loads
Recommended loads are indicated in the
programme charts.
General rules:
Cotton, linen: drum full but not too tightly packed;
Synthetics: drum no more than half full;
Delicate fabrics and woollens: drum no more than
one third full.
Washing a maximum load makes the most efficient
use of water and energy.
For heavily soiled laundry, reduce the load size.
Laundry weights
The following weights are indicative:
bathrobe 1200 g
napkin 100 g
quilt cover 700 g
sheet 500 g
pillow case 200 g
tablecloth 250 g
towels 200 g
tea cloth 100 g
night dress 200 g
ladies briefs 100 g
mans work shirt 600 g
mans shirt 200 g
mans pyjamas 500 g
blouse 100 g
mens underpants 100 g
Removing stains
Stubborn stains may not be removed by just water
and detergent. It is therefore advisable to treat them
prior to washing.
Blood: treat fresh stains with cold water. For dried
stains, soak overnight in water with a special
detergent then rub in the soap and water.
Oil based paint: moisten with benzine stain
remover, lay the garment on a soft cloth and dab the
stain; treat several times.
Dried grease stains: moisten with turpentine, lay
the garment on a soft surface and dab the stain with
the fingertips and a cotton cloth.
Rust: oxalic acid dissolved in hot water or a rust
removing product used cold. Be careful with rust
stains which are not recent since the cellulose
structure will already have been damaged and the
fabric tends to hole.
Mould stains: treat with bleach, rinse well (whites
and fast coloureds only).
Grass: soap lightly and treat with bleach (whites and
fast coloureds only).
Ball point pen and glue: moisten with acetone (*),
lay the garment on a soft cloth and dab the stain.
Lipstick: moisten with acetone as above, then treat
stains with methylated spirits. Remove any residual
marks from white fabrics with bleach.
Red wine: soak in water and detergent, rinse and
treat with acetic or citric acid, then rinse. Treat any
residual marks with bleach.
im_ewf1090_eu.qxd 05/09/2005 17:11 Pagina 12
ENGLISH
!
Ink: depending on the type of ink, moisten the fabric
first with acetone (*), then with acetic acid; treat any
residual marks on white fabrics with bleach and then
rinse thoroughly.
Tar stains: first treat with stain remover, methylated
spirits or benzine, then rub with detergent paste.
(*) do not use acetone on artificial silk.
Detergents and additives
Good washing results also depend on the choice of
detergent and use of the correct quantities to avoid
waste and protect the environment. Although
biodegradable, detergents contain substances
which, in large quantities, can upset the delicate
balance of nature.
The choice of detergent will depend on the type of
fabric (delicates, woollens, cottons, etc.), the colour,
washing temperature and degree of soiling.
All commonly available washing machine detergents
may be used in this appliance:
 powder detergents for all types of fabric,
 powder detergents for delicate fabrics (60°C max)
and woollens,
 liquid detergents, preferably for low temperature
wash programmes (60°C max) for all types of
fabric, or special for woollens only.
The detergent and any additives must be placed in
the appropriate compartments of the dispenser
drawer before starting the wash programme.
If using concentrated powder or liquid detergents, a
programme without prewash must be selected.
The washing machine incorporates a recirculation
system which allows an optimal use of the
concentrated detergent.
Pour liquid detergent into the dispenser drawer
compartment marked just before starting the
programme.
Any fabric softener or starching additives must be
poured into the compartment marked before
starting the wash programme.
Follow the product manufacturers recommendations
on quantities to use and do not exceed the «MAX»
mark in the detergent dispenser drawer.
Quantity of detergent to be used
The type and quantity of detergent will depend on
the type of fabric, load size, degree of soiling and
hardness of the water used.
Water hardness is classified in so-called degreesof
hardness. Information on hardness of the water in
your area can be obtained from the relevant water
supply company, or from your local authority.
Follow the product manufacturers instructions on
quantities to use.
Use less detergent if:
 you are washing a small load,
 the laundry is lightly soiled,
 large amounts of foam form during washing.
im_ewf1090_eu.qxd 05/09/2005 17:11 Pagina 13
International wash code symbols
These symbols appear on fabric labels, in order to help you choose the best way to treat your laundry.
Energetic wash
Delicate wash
Max. wash
temperature
95°C
Max. wash
temperature
60°C
Max. wash
temperature
40°C
Max. wash
temperature
30°C
Hand wash Do not
wash
at all
Bleaching Bleach in cold water Do not bleach
Ironing Hot iron
max 200°C
Warm iron
max 150°C
Lukewarm iron
max 110°C
Do not iron
Dry cleaning Dry cleaning
in all solvents
Dry cleaning in
perchlorethylene,
petrol, pure alcohol,
R 111 & R 113
Dry cleaning
in petrol,
pure alcohol
and R 113
Do not
dry clean
Drying Flat On the line On clothes
hanger
Tumble dry
high
temperature
low
temperature
Do not
tumble dry
95
60
60
40
30
30
14
im_ewf1090_eu.qxd 05/09/2005 17:11 Pagina 14
ENGLISH
#
Operating sequence
Before the first wash we recommend that you pour 2
litres of water into the main wash compartment
of the detergent drawer. Then run a cotton cycle at
60°C, with the machine empty, in order to remove
any manufacturing residue from the drum and tub.
Pour half a measure of detergent into the main wash
compartment and start up the machine.
1. Place the laundry in the drum
Open the door.Place the laundry in the drum, one
item at a time, shaking them out as much as
possible.Close the door.
2. Measure out the detergent
Pull out the dispenser drawer until it stops. Measure
out the amount of detergent recommended by the
manufacturer in a graduated cup and pour it into the
main wash compartment .
If you wish to carry out the prewash or soak phase,
pour detergent into the appropriate compartment
marked .
3. Measure out the additive
If required, pour fabric softener into the compartment
marked , without exceeding the «MAX» mark.
C0065
C0064
P0004
4.Switch the machine ON and OFF
Turn the selector dial to the desired programme to the
switch appliance on.To switch the appliance off turn
it to Off.
5.Select the desired programme
Turn the selector dial to the desired position: the LED
corresponding to the different phases making up the
selected programme illuminate.
The duration of the programme appears in the display.
6.Select the temperature
Press the Temp. button if you wish to select a
temperature value different from the one proposed by
the washing machine. The relevant LED will light up.
im_ewf1090_eu.qxd 05/09/2005 17:11 Pagina 15
$
7. Select the spin speed or No
Spin Option
Press the Spin button repeatedly, in order to select
the desired spin speed or the No Spin option. The
relevant LED will light up.
If you select the No Spin option, the machine will
stop at the end of the programme eliminating the spin
phase.
EWF 1090
8.Select the desired option
Press the relevent button to select the required
options. Depending on the selected programm, only
certain options are avialable and shown during the
selection phase.
Note:Not all the options are compatible between
themselves. The uncompatible option icons will
disappear.
9. Select the Delay Start
Before you start the programme if you wish the
starting to be delayed, press the Delay Start button.
The figures corresponding to the selected delay will
be displayed for about 3 seconds, after which the
duration of the selected programme will appear on
the display.
During this period it is possible to load other laundry:
Press Start/Add clothes button;
load the laundry;
close the door and press Start/Add clothes
button again.
10. Start the Programme
Press the Start/Add clothes button. The relevant
LED will stop flashing. and only the LED relevant
to the phase that is in progress will remain lit.
If you have chosen a delayed start, the washing
machine will begin the countdown.
The display will show the duration of the programme
or the selected delay.
11. How to change a programme
during its cycle
You can alter the programme before it starts.
When the programme has started, you can only reset
it by turning the programme selector dial to «Off»
position and then you can select the new
programme. Start it by pressing the Start/Add
clothes button.
12. How to interupt a programme
during its cycle
Press the Start/Add clothes button to interrupt a
programme which is running, the corresponding LED
starts to flash. Press the same button again to restart
the programme.
im_ewf1090_eu.qxd 05/09/2005 17:11 Pagina 16
ENGLISH
%
13. Cancelling a programme
Turn the selector dial to position «Off» to cancel a
programme which is running. Now you can select a
new programme.
14. How to open the door during
the cycle of a programme
You can open the door, after having set the washing
machine to PAUSE phase, by pressing Start/Add
clothes button provided the following conditions
exist:
1) the washing machine is not in the heating phase
beyond 55°C
2) the level of the water is not high;
3) the drum is not turning.
After approximately 3 minutes, you can open the
door.
Pay attention to the level and temperature of the
water in the washing machine!
15.End of programme
The washing machine stops automatically at the end
of the ptogramme giving an audible signal.
If the No Spin option has been selected, the LED
of the Start/Add clothes button goes off, the LED
and the End LED remain lit to indicate that the spin
phase is eliminated.
To spin the laundry select the spin speed by means of
the relevant button and then press the Start/Add
clothes button. The laundry is spun at the selected
spin speed.
Turn the programme selector dial to position «Off» to
switch the machine off.
Remove the laundry from the washing machine.
Check whether the drum is completely empty, by
rotating it with your hand. The purpose of this is to
prevent any items of laundry from remaining
accidentally in the drum, where they might get
damaged in a subsequent wash (e.g. by shrinking) or
bleed colour into another load of laundry.
We advise you to close the water supply tap and
disconnect the plug from the socket.
Leave the door ajar in order to air the washing
machine.
im_ewf1090_eu.qxd 05/09/2005 17:11 Pagina 17
18
*This programme at 60c is the reference program for the energy label according to EEC directive 92/75
Programme table
Washing Programmes
Cotton
Cotton Eco
Daily Cotton*
Easy Iron
Delicate
Wool
Silk
White and coloured
cotton e.g Sheets,
tablecloths,
household linen
Coloured cotton
e.g. shirts, blouses,
towels and
undergarments
Synthetics and
Delicates
Delicate fabrices,
e.g. acryllics,
Polyester mixture
Delicate fabrices,
Silk to be
handwashed
Main wash
at 40°C-60°C
3 rinses
Long spin
8 kg
4,5 kg
4.5 kg
3.5 kg
3.5 kg
2 kg
1 kg
Main wash
at 40°C-60°C
3 rinses
Long spin
Main wash
at Cold-60°C
3 rinses
Long spin
Main wash
at Cold-60°C
3 rinses
Short spin
Main wash
at Cold-40°C
3 rinses
Short spin
Main wash
at 30°C
3 rinses
Short spin
Clothes labelled
Pure new wool,
non-shrink machine
washable and silk
fabric
Main wash
at Cold-40°C
3 rinses
Short spin
Wash
programmes
Fabrics
Type of Laundry Description
of Programme
Max.
Load
Prewash
Extra Rinse
Easy Iron
No Spin
Prewash
Extra Rinse
Easy Iron
No Spin
Prewash
Extra Rinse
No Spin
Time Save.
No Spin.
Extra Rinse
No Spin.
No Spin
Prewash
Extra Rinse
Easy Iron
No Spin
Time Save
Available options
Economy wash for
whites or fast coloured
cotton or linen fabrics,
normally soiled shirts
Jeans Coloured cotton or
linen fabric, normally
soiled shirts, blouses
8 kg Main wash
at Cold-60°C
3 rinses
Long spin
Prewash
Time Save
Extra Rinse
No Spin
Easy Iron.
Synthetics Synthetics or mixed
fabrice e.g lingerie,
coloured garments
8 kg Main wash
at Cold-40°C
3 rinses
Short spin
Prewash
Time Save
Extra Rinse
No Spin.
im_ewf1090_eu.qxd 05/09/2005 17:11 Pagina 18
ENGLISH
19
Programme table
Special Programmes
Wash
programmes
Fabrics
Type of Laundry Description
of Programme
Availble options Max.
Load
For Draining out
last rinse water in
programmes with
the rinse hold option
Separate rinse cycle
for hand washed
items of cotton
fabrics.
Hand Wash
Quick 30
Drain
Rinse & Spin
Spin
Delicate Spin
Special programme
for hand washing
fabrics.
Special Programme
for extremly delicate
items
Seperate Spin
for Cottons
Seperate spin
for delicate items
Main Wash
at 30°C
3 Rinses
Short Spin
Draning Of Water
3 rinses with liquid
additive if required
long spin at
maximum speed.
2 kg
4.5 kg
8 kg
8 kg
No Spin
Main Wash
at 30°C-40°C
3 Rinses
Short Spin
No Spin
Drain and Spin at
maximum speed
8 kg
Short Spin 3.5 kg
No Spin
Easy Iron
Extra Rinse
im_ewf1090_eu.qxd 05/09/2005 17:11 Pagina 19
20
Maintenance
1. Bodywork
Clean the outside of the machine with soap and
water only. Rinse with clean water and dry with a soft
cloth.
Important: do not use methylated spirits, solvents or
similar products to clean the bodywork.
2. Door seal
Check from time to time the door seal and eliminate
eventual possible objects that could be trapped in
the fold.
3. Detergent dispenser drawer
After a while, detergents and fabric softeners leave
deposits in the drawer.
Clean the drawer from time to time by rinsing it under
a running tap. To remove the drawer from the
machine, press the button in the rear left-hand
corner.
To facilitate cleaning, the top part of the additive
compartments can be removed.
C0119
C0118
P1050
Detergent can also accumulate inside the drawer
recess: clean it with an old toothbrush. Refit the
drawer after cleaning.
4. Drain pump
The pump should be inspected if
the machine does not empty and/or spin
the machine makes an unusual noise during
draining due to objects such as safety pins, coins
etc. blocking the pump.
Proceed as follows:
Disconnect the appliance.
If necessary wait until the water has cooled down.
Open the pump door.
Place a container close to the pump to collect any
spillage.
Release the emergency emptying hose, place it in
the container and remove its cap.
When no more water comes out, unscrew the
pump cover and remove the pump. Always keep a
rag nearby to dry up spillage of water when
removing the pump.
P1115
P1114
P0038
im_ewf1090_eu.qxd 05/09/2005 17:11 Pagina 20
1 / 1

Electrolux EWF1090 Manuale utente

Categoria
Lavatrici
Tipo
Manuale utente