Seagate 240 DDS-4 Manuale utente

Scorpion 240 DDS-4 Autoloader

Part Number 100135972

November 2000

Installation Manual

Section A: English

Section B: Français

Section B: Deutsch

Section D: Español

Section E: Nihongo

Scorpion 240 DDS-4 Autoloader

Installation Manual

Section A: English

Section

B: Fran

ç

ais

Section

C: Deutsch

Section

D: Español

Section

E:

Scorpion 240 DDS-4 Autoloader

Installation Manual

Section A

English

Part Number 100135972

Seagate and the Seagate logo are registered trademarks of Seagate

Technology, LLC. Scorpion 240 and the Scorpion logo are either

trademarks or registered trademarks of Seagate Removable Storage

Solutions LLC. Other product names are registered trademarks or

trademarks of their owners.

Seagate reserves the right to change, without notice, product offerings or

specifications. No part of this publication may be reproduced in any form

without written permission from Seagate Removable Storage Solutions.

Publication Number: 10007066-003, November 13, 2000

Contents

Contents A-3

FCC notice A-5

Introduction A-7

About this user’s guide A-7

About the Scorpion 240 autoloader A-7

Before you begin A-9

Precautions A-9

Unpacking and inspection A-9

Installing the internal autoloader A-10

Configuring the internal autoloader A-10

Mounting the internal autoloader A-15

Connecting the SCSI interface cable A-16

Connecting a power cable A-17

Installing the external autoloader A-18

Configuring the external Scorpion 240 A-18

Connecting the power cord A-20

Operation and maintenance A-21

Starting the autoloader A-21

Using cartridges and magazines A-22

About the front-panel buttons A-26

About the front-panel LEDs A-27

About the front-panel LCD display A-30

Cleaning the tape drive A-34

DDS-4 cartridge information A-37

Preparation for shipping A-38

Configuration for UNIX, Novell, and Windows NT

operating systems A-40

Operating-system configuration dip switches A-40

Configuration for the Windows NT environment A-41

Configuration for Novell environments A-41

Configuration for the DEC UNIX environment A-43

Configuration for the Sun UNIX environment A-45

Configuration for the SGI environment A-47

Configuration for the HP-UX environment A-51

Configuration for the IBM AIX environment A-52

Configuration for SCO UNIX A-53

Configuration for LINUX A-53

Summary of drive specifications A-54

Support services A-56

FCC notice

This equipment generates and uses radio frequency energy and, if not

installed and used in strict accordance with the manufacturer's

instructions, may cause interference to radio and television reception,

which could void the user's authority to operate the equipment. It has been

tested and found to comply with the limits for a Class B digital device

pursuant to Part 15 of FCC Rules, which are designed to provide

reasonable protection against such interference in a residential installation.

However, there is no guarantee that interference will not occur in a

particular installation. If interference does occur, try to correct it by taking

one or more of the following measures:

•

Reorient or relocate the receiving antenna.

•

Increase the separation between the computer and the receiver.

•

Connect the computer into an outlet on a circuit different from that to

which the receiver is connected.

•

Consult the dealer or an experienced radio/television technician for

help.

You may find the following booklet prepared by the Federal

Communications Commission helpful:

How to Identify and Resolve Radio–

TV Interference Problems.

This booklet (Stock No. 004-000-00345-4) is

available from the U.S. Government Printing Office, Washington, DC

20402.

This equipment complies with the limits for Class B digital apparatus in

accordance with Canadian Radio Interference Regulations.

Cet appareil numérique de la classe B est conforme au Règlement sur

brouillage radioélectrique, C. R. C., ch. 1374.

Scorpion 240 Autoloader Installation Manual A-7

Introduction

About this user’s guide

This user’s guide contains information on installing and

operating the Scorpion 240 DDS-4 autoloader.

About the Scorpion 240 autoloader

The Seagate internal Autoloader is a fully integrated,

intelligent, multicartridge tape system that supports the DDS

(Digital Data Storage), DDS-1, DDS-2, DDS-3, and DDS-4

tape formats. It includes a magazine that can accommodate

up to six tape cartridges.

The internal autoloader (STDL42401LW) is designed to be

installed inside a computer, in a 5.25-inch, full-height drive

bay. The external autoloader (STDL62401LW) is a standalone

subsystem that connects to a host system using a 68-pin

shielded SCSI cable.

Note:

The Scorpion 240 will not work in a SCSI-1

environment.

The Scorpion 240 autoloader combines established DDS

technology, high density recording and hardware data-

compression capability, and Seagate's proven computer-

grade DDS tape drive to provide unmatched reliability and

performance.

A-8 Scorpion 240 Autoloader Installation Manual

Drive applications

The Scorpion 240 autoloader is ideal for server and

network/enterprise applications, including:

•

Backup of high-capacity disc drives or disc arrays

•

Automated storage management

•

On-line, unattended data collection

•

Near-line secondary storage for text, graphics or

multimedia data of all types

•

Archival storage.

Scorpion 240 capacity and data-transfer rates

The Scorpion 240 provides the following capacities and

sustained data-transfer rates, depending upon the type and

length of tape media used. These capacities and data-transfer

rates are based on a 2:1 data compression. Uncompressed

capacities are one half these values.

Tape format: DDS DDS-2 DDS-3 DDS-4

Tape length (m)

90 120 125 150

Single-cartridge

capacity (Gbytes)

4.0 8.0 24.0 40.0

Six-cartridge

magazine capacity

(Gbytes)

24.0 48.0 144.0 240.0

Sustained Data-

transfer Rate

(Mbyte/sec)

1.83 1.83 5.5 5.5

Note. 60-meter DDS tape cannot be used with this drive.

Scorpion 240 Autoloader Installation Manual A-9

Before you begin

Precautions

Caution.

Observe the following precautions to avoid

electrostatic damage to the internal autoloader.

•

Do not remove the drive from the antistatic bag until you

are ready to install it.

•

Before you remove the drive from the antistatic bag, touch

a grounded metal surface to discharge any static

electricity buildup from your body.

•

Hold the drive only by its edges and avoid direct contact

with any electronic components.

•

If you need to put down the drive, lay it on top of the

antistatic bag or place it inside the bag.

Unpacking and inspection

Although Seagate autoloaders are inspected and carefully

packaged at the factory, damage may occur during shipping.

Follow these steps for unpacking the autoloader.

1. Inspect the shipping container. Notify your shipper

immediately if you find any damage.

2. Place the shipping container on a flat, clean, stable

surface. Then carefully remove the contents and verify

the packing list. If parts are missing or the equipment is

damaged notify your Seagate representative.

3. Save the drive container and packing materials in case

you ever need to ship the drive.

A-10 Scorpion 240 Autoloader Installation Manual

Installing the internal autoloader

This chapter describes how to configure, mount, and attach

cables to the

internal

Scorpion 240 autoloader.

Configuring the internal autoloader

Before you install the internal version of the Scorpion 240 in

your computer, you may need to configure the drive to work

with your system.

Default settings

The default settings for the internal drive are listed below:

•

The drive is set for SCSI ID 6.

•

Parity checking is enabled.

•

SCSI terminator power is disabled.

•

Data compression is enabled.

•

Power-on self-test diagnostics are enabled.

•

MRS checking is enabled

(the drive will not write to non-MRS tapes).

If these default settings are appropriate for your computer

system, then continue to “Mounting the internal autoloader” on

page A-15.

Changing jumper settings

To change the SCSI ID, parity checking, or termination power,

use the jumpers on the back of the drive, as shown in Figure

1 on the following page.

Note.

Power down the drive before changing jumpers or dip

switches. Changes take effect when the drive restarts.

Scorpion 240 Autoloader Installation Manual A-11

Figure 1. Jumper pins on the back of the Scorpion 240

SCSI ID=0

SCSI ID=1

SCSI ID=2

SCSI ID=3

SCSI ID=4

SCSI ID=5

SCSI ID=6

SCSI ID=7

SCSI ID=8

SCSI ID=9

SCSI ID=10

SCSI ID=11

SCSI ID=12

SCSI ID=13

SCSI ID=14

SCSI ID=15

Parity enable

Term. power

Default jumper settings shown

(SCSI ID 6, parity checking enabled,

and termination power disabled)

Pins: Function:

1-2 SCSI ID bit 0

3-4 SCSI ID bit 1

5-6 SCSI ID bit 2

7-8 SCSI ID bit 3

9-10 Parity checking

11-12 Termination Power

A-12 Scorpion 240 Autoloader Installation Manual

SCSI Address Selection (pins 1 through 8)

Each SCSI device on a SCSI bus must have a unique SCSI

ID. The SCSI controller or host adapter generally uses ID 7.

In some systems, the boot drive uses ID 0 or ID 1.

You can select an appropriate SCSI address used by the

drive by placing the appropriate jumpers on pins pairs 1-2

through 7-8, as shown in Figure 1.

Note: SCSI ID numbers 8 through 15 will only be recognized

if dip switch 9 is “ON.” See page A-14 for details.

Parity checking (pins 9 and 10)

If a jumper is installed on pins 9 and 10, parity checking is

enabled. If no jumper is installed, parity checking is disabled,

but parity is still generated by the drive.

Terminator power (pins 11 and 12)

If a jumper is installed on pins 11 and 12, terminator power is

enabled.

Note: The internal Scorpion 240 does

not

provide SCSI

termination, and therefore should not be installed as

the last device in a SCSI chain. See “SCSI termination”

on page A-16 for more information.

If the terminator power jumper is installed, be careful not to

short the TERMPWR signal to ground. In the event of a short,

terminator power to the bus will be interrupted. After the short

is removed, a fuse in the drive will automatically reset,

restoring terminator power.

Changing dip-switch settings

To change data compression, MRS checking, power-on self-

test diagnostics, operating system settings, Wide/Narrow

SCSI selection, or the drive’s inquiry string, you must use the

dip switches on the underside of the internal drive.

Scorpion 240 Autoloader Installation Manual A-13

Figure 2 shows the location of dip switches on the

underside

of the internal Scorpion 240. Each of these switches is

described in detail on subsequent pages.

Note. Power down the drive before changing jumpers or dip

switches. Changes take effect when the drive restarts.

Figure 2. Dip-switch settings for internal Scorpion 240

Data compression (DC)

SCSI DC control

Media recognition

Self Test

Wide/Narrow SCSI

Inquiry String support

1

2

3

4

5

6

7

8

9

10

O

N

Default settings shown

Operating-system

configuration

switches

Data compression (switches 1 and 2)

If switch 1 is ON (the default setting), hardware data

compression is enabled when the drive is powered on. If

switch 1 is OFF, hardware data compression is disabled at

power-on.

If dip switch 2 is ON (the default setting) then SCSI commands

can be used to enable or disable hardware data compression. To

prevent hardware data compression from being enabled or

disabled by SCSI commands, set dip switch 2 to OFF.

Media-recognition system (switch 3)

The media-recognition system allows the drive to determine

whether a given tape cartridge conforms to the DDS tape

standard. Use of non-DDS media may appear to give

A-14 Scorpion 240 Autoloader Installation Manual

satisfactory results, but the inferior specifications of such

media can cause data-integrity problems.

Switch 3 enables or disables the media-recognition system

(MRS). If switch 3 is ON (the default setting), the drive reads

and writes to MRS media and reads from but does not write to

non-MRS media. If switch 3 is OFF, the drive reads or writes

both MRS and non-MRS media.

Power-on self-test enable/disable (switch 4)

Switch 4 enables or disables execution of power-on self-test

diagnostics when the drive is powered on. If switch 4 is ON

(the default setting), the drive performs a power-on self test. If

switch 4 is OFF, the drive does not perform a power-on self

test.

Operating System configuration (switches 5 through 8)

Switches 5 through 8 are used to configure the drive for use

with UNIX, Novell, and Windows NT operating systems.

These procedures are described starting on page A-40. The

default setting for all four of these switches is ON.

SCSI Wide/Narrow (switch 9)

Switch 9 enables or disables SCSI Wide operation on the

SCSI bus. When switch 9 is ON (the default setting), the drive

is capable of operating in Wide (16-bit) SCSI mode. When

switch 9 is OFF, the drive will only operate as a Narrow (8-bit)

SCSI device.

Note: If switch 9 if set to OFF, the drive can only use SCSI ID

values 0 through 7.

Inquiry String (switch 10)

Switch 10 is used to select the Vendor ID that the drive

returns when queried with a SCSI Inquiry command. When

switch 10 is ON (the default setting), the Vendor ID will be

“SEAGATE DAT.” When switch 10 is OFF the Vendor ID will

be “ARCHIVE Python.” The “ARCHIVE Python” Vendor ID

may be used by independent software vendors to provide

software compatibility with previous Seagate DDS tape drives.

Scorpion 240 Autoloader Installation Manual A-15

Mounting the internal autoloader

The Scorpion 240 must be mounted horizontally in a 5.25-

inch, full-height drive bay. Mount the drive using four M3.0

metric screws on the sides or bottom of the drive, as shown in

Figure 3. Do not use screws longer than 4 mm or you may

damage the drive.

Note.

When mounting the drive, make sure that nothing

blocks the exhaust fan or the ventilation slots on the

bottom and rear of the autoloader.

Figure 3. Locations of mounting holes

MOUNT HOLE

M3 (4 PLACES)

86

± 0.25

1.8

± 0.25

7.0

± 0.3

45.5

± 0.25

203.2

± 0.25

79.5

± 0.25

11.9

± 0.3

82.6

± 0.6

21.8

± 0.3

45.5

± 0.25

M3 (4 PLACES)

MOUNTING HOLE

149.6

± 0.25

203.2

± 0.5

79.5

± 0.25

139.7

± 0.3

146 +1

.5 –0.5

1.8

± 0.25

224.0 max

A-16 Scorpion 240 Autoloader Installation Manual

Connecting the SCSI interface cable

Turn off all power to your computer and drive. Then connect a

68-pin wide internal SCSI cable from your SCSI controller to

the SCSI connector on the back of the autoloader. Make sure

that pin 1 on the SCSI controller and cable is connected to pin

1 on the drive. Figure 4 shows the location of SCSI pin 1 on

the drive’s SCSI connector. Pin 1 on the SCSI cable should

be indicated by a colored stripe.

Scorpion 240 drives can be used with two different types of

SCSI interfaces: Ultra2 SCSI (LVD) or “Wide” (16-bit) single-

ended SCSI. The drive can automatically detect whether it is

connected to an LVD or single-ended wide SCSI bus.

Note: The Scorpion 240 will not operate properly in a SCSI-1

environment.

Figure 4. Interface connectors on internal Scorpion 240

Power connector

pin 4

+5V

pin 3: GND

(+5V return)

pin 2: GND

(+12V return)

pin 1

12V

Ultra2 SCSI 68-pin

high-density connector

pin 34

pin 68

pin 35

pin 1

SCSI Termination

The internal Scorpion 240 does

not

provide SCSI termination.

For this reason, it should not be the last device on a SCSI

chain. Two termination examples are shown in Figure 5 on

the following page. If the drive is the only SCSI device, attach

the drive to the connector which is next to last on the SCSI

Scorpion 240 Autoloader Installation Manual A-17

chain and attach an LVD/single-ended multi-mode terminator

to the last connector in the chain.

Figure 5. Two SCSI termination examples for the internal

Scorpion 240.

SCSI Controller

(termination enabled)

Internal

Tape drive

SCSI device

(

termination

enabled

)

SCSI device

(

termination

disabled

)

SCSI device

(

termination

disabled

)

(no

termination

)

SCSI Terminator

SCSI Controller

(termination enabled)

Internal

Tape drive

(no

termination

)

Connecting a power cable

Attach a 5/12-volt, four-pin power cable to the power

connector on the back of the drive. Figure 4 on the previous

page shows the location of the power connector.

The recommended 4-pin power connector for the internal

drive is an AMP 1-48024-0 housing with AMP 60617-1 pins or

equivalent.

A-18 Scorpion 240 Autoloader Installation Manual

Installing the external autoloader

The external Scorpion 240 is a compact external drive that

connects to the host computer as a turnkey subsystem.

Installing the external drive involves three simple steps:

1. Configuring the drive

2. Connecting the SCSI interface cable

3. Connecting the power cord

Configuring the external Scorpion 240

The following is the default configuration for the external

Scorpion 240:

•

SCSI ID:

6

•

Media Recognition System (MRS) checking:

enabled.

•

Parity checking:

enabled.

•

Data compression:

enabled.

•

Power-on self-test diagnostics:

enabled.

•

Host operating system:

Windows 95/98/NT/2000

•

Termination power:

supplied to the SCSI bus.

Setting the SCSI ID

Make sure that the drive is turned off; then set the SCSI ID for

the drive using the push-button switch on the back of the

external drive. Figure 6 on the following page shows this

switch, as well as the two SCSI interface connectors, on/off

switch, and the power-cord connector.

Note:

The drive must be restarted for any change in SCSI ID

to take effect.

La pagina sta caricando ...

Seagate 240 DDS-4 Manuale utente

Questo manuale è adatto anche per

Seagate 240 DDS-4 Manuale utente

in altre lingue

Documenti correlati

Altri documenti