Toshiba GC10-QM Manuale utente

TOSHIBA TEC Bar Code Printer

B-SV4D-GS/GC10-QM

External Equipment Interface Specification

First Edition: Jun. 02, 2003

i

TABLE OF CONTENTS

Page

1. SCOPE........................................................................................................................................ 1

2. GENERAL DESCRIPTION......................................................................................................... 1

3. INTERFACE................................................................................................................................ 2

3.1 SERIAL INTERFACE............................................................................................................. 2

3.2 PARALLEL INTERFACE ....................................................................................................... 6

4. KEY OPERATION FUNCTIONS................................................................................................ 8

4.1 SYSTEM MODE (POWER UP WITH KEY PRESSED) ........................................................ 8

4.2 ON-LINE MODE FUNCTIONS .............................................................................................. 9

5. TRANSMISSION SEQUENCE ................................................................................................... 10

5.1 INITIALIZATION .................................................................................................................... 10

5.2 LABEL ISSUE OPERATION.................................................................................................. 12

6. INTERFACE COMMANDS......................................................................................................... 14

6.1 OUTLINE OF COMMANDS................................................................................................... 14

6.2 LIST OF COMMANDS........................................................................................................... 16

6.3 COMMANDS FOR CREATING APPLICATION .................................................................... 17

6.3.1 LABEL SIZE SET COMMAND.......................................................................................... 17

6.3.2 POSITION FINE ADJUST COMMAND............................................................................ 22

6.3.3 PRINT DENSITY FINE ADJUST COMMAND.................................................................. 27

6.3.4 IMAGE BUFFER CLEAR COMMAND.............................................................................. 28

6.3.5 CLEAR AREA COMMAND............................................................................................... 29

6.3.6 LINE FORMAT COMMAND.............................................................................................. 31

6.3.7 BIT MAP FONT FORMAT COMMAND............................................................................ 35

6.3.8 OUTLINE FONT FORMAT COMMAND........................................................................... 49

6.3.9 BAR CODE FORMAT COMMAND................................................................................... 63

6.3.10 BIT MAP FONT DATA COMMAND.................................................................................. 94

6.3.11 OUTLINE FONT DATA COMMAND................................................................................. 97

6.3.12 BAR CODE DATA COMMAND ........................................................................................ 100

6.3.13 ISSUE COMMAND........................................................................................................... 113

6.3.14 FEED COMMAND............................................................................................................ 123

6.3.15 EJECT COMMAND .......................................................................................................... 128

6.3.16 FORWARD/REVERSE FEED COMMAND...................................................................... 129

6.3.17 STORAGE AREA ALLOCATE COMMAND ..................................................................... 131

6.3.18 MEMORY CARD FORMAT COMMAND.......................................................................... 133

6.3.19 2-BYTE WRITABLE CHARACTER CODE RANGE COMMAND..................................... 134

6.3.20 BIT MAP WRITABLE CHARACTER COMMAND ............................................................ 135

ii

Page

6.3.21 GRAPHIC COMMAND ..................................................................................................... 146

6.3.22 SAVE START COMMAND ............................................................................................... 154

6.3.23 SAVE TERMINATE COMMAND ...................................................................................... 156

6.3.24 SAVED DATA CALL COMMAND..................................................................................... 157

6.3.25 RESET COMMAND.......................................................................................................... 158

6.3.26 STATUS REQUEST COMMAND..................................................................................... 159

6.3.27 RECEIVE BUFFER FREE SPACE STATUS REQUEST COMMAND............................. 160

6.3.28 VERSI0N INFORMATION ACQUIRE COMMAND........................................................... 162

6.3.29 MEMORY BOARD INFORMATION ACQUIRE COMMAND............................................ 163

6.3.30 PRINTER INFORMATION STORE COMMAND.............................................................. 165

6.3.31 PRINTER INFORMATION REQUEST COMMAND......................................................... 166

6.4 COMMANDS FOR SYSTEM ADMINISTRATOR.................................................................. 167

6.4.1 PARAMETER SET COMMAND ....................................................................................... 167

6.4.2 FINE ADJUSTMENT VALUE SET COMMAND ............................................................... 170

6.4.3 BATCH RESET COMMAND............................................................................................. 172

7. CONTROL CODE SELECTION................................................................................................. 173

8. ERROR PROCESSING.............................................................................................................. 174

8.1 COMMUNICATION ERRORS............................................................................................... 174

8.2 ERRORS IN ISSUING OR FEEDING.................................................................................... 174

8.3 ERRORS IN WRITABLE CHARACTER AND PC COMMAND SAVE MODES .................... 176

9. STATUS RESPONSE................................................................................................................. 177

9.1 SERIAL INTERFACE............................................................................................................. 177

9.1.1 FUNCTIONS..................................................................................................................... 177

9.1.2 STATUS FORMAT ........................................................................................................... 177

9.1.3 DETAIL STATUS.............................................................................................................. 178

9.2 PARALLEL INTERFACE ....................................................................................................... 179

10. LED INDICATIONS..................................................................................................................... 181

iii

Page

11. CHARACTER CODE TABLE..................................................................................................... 183

11.1 TIMES ROMAN, HELVETICA, LETTER GOTHIC, PRESTIGE ELITE, COURIER............... 183

11.2 PRESENTATION................................................................................................................... 190

11.3 TEC OUTLINE FONT 1......................................................................................................... 194

11.4 TrueType FONT..................................................................................................................... 201

12. BAR CODE TABLE.................................................................................................................... 208

13. DRAWING OF BAR CODE DATA.............................................................................................. 221

14. AUTOMATIC ADDING OF START/STOP CODE...................................................................... 242

- 1 -

1. SCOPE

This specification applies to the external equipment interface for use with the Model B-SV4D general-

purpose thermal label/tag printers.

2. GENERAL DESCRIPTION

The external equipment interface connects a printer to the host computer through a serial interface (RS-

232C), parallel interface (Centronics), or a network for making various settings and printing labels.

This specification describes how to use the external equipment interface.

The model configuration is described below.

B-SV4D

Flash ROM 1 MB

Memory DRAM 2 MB

Interface

Standard RS-232C

Centronics

USB

Option LAN adapter

Full cut Cutter

Partial cut (option)

Strip module Option

- 2 -

3. INTERFACE

3.1 SERIAL INTERFACE

(1) Type : Conforming to RS-232C

(2) Mode of Communication : Full duplex

(3) Transmission Speed : 2400 BPS

4800 BPS

9600 BPS

19200 BPS

38400 BPS

57600 BPS

(4) Synchronization Method : Start-stop synchronization

(5) Start Bit : 1 bit

(6) Stop Bit : 1 bit

2 bits

(7) Data Length : 7 bits

8 bits

(8) Parity : None

Even

Odd

(9) Error Detection : Parity Error Vertical parity error check

Framing Error This error occurs if no stop bit is found in the frame

specified starting with the start bit.

Overrun Error This error occurs if the next data is input before the

data input to the UART from the host is read by the

printer CPU.

(10) Protocol : No-procedure method

(11) Data Input Code : ASCII code

European character set 8 bit code

Graphics 8 bit code

(12) Receive Buffer : 515K bytes

- 3 -

(13) Transmission Control : XON/XOFF (DC1/DC3) Protocol

READY/BUSY (DTR) Protocol

XON/XOFF (DC1/DC3) Protocol + READY/BUSY (DTR)

Protocol

RTS Protocol

XON/XOFF (DC1/DC3) Protocol

When initialized after power on, this printer becomes ready to receive data and sends an

XON code (11H). (Transmission or non-transmission of the XON code is selectable by

means of the parameter setting.)

The printer sends an XOFF code (13H) when the blank positions in the receive buffer

become 1K bytes or less.

The printer sends an XON code (11H) when the blank positions in the receive buffer are 2K

bytes or more.

When there are no blank positions in the receive buffer, the printer discards data received

exceeding the receive buffer capacity, without storing it in the buffer. (After detecting the

XOFF code, the host computer must stop transmission before the printer receive buffer

becomes full.)

The printer sends an XOFF code (13H) when the power is off. (Transmission or non-

transmission of the XOFF code is selectable by means of the parameter setting.)

READY/BUSY (DTR) Protocol

When initialized after power on, this printer becomes ready to receive data and turns the

DTR signal to “High” level (READY).

The printer turns the DTR signal to “Low” level (BUSY) when the blank positions in the

receive buffer are 1K bytes or less.

The printer turns the DTR signal to “High” level (READY) when the blank positions in the

receive buffer are 2K bytes or more.

When there are no blank positions in the receive buffer, the printer discards data received

exceeding the receive buffer capacity, without storing it in the buffer. (After detecting the

BUSY signal, the host computer must stop transmission before the printer receive buffer

becomes full.)

The RTS signal is always “High”.

- 4 -

XON/XOFF (DC1/DC3) Protocol + READY/BUSY (DTR) Protocol

When initialized after power on, this printer becomes ready to receive data and turns the

DTR signal to “High” level (READY). The printer also sends an XON code (11H).

When the blank positions in the receive buffer are 1K bytes or less, the printer turns the

DTR signal to “Low” level (BUSY) and sends an XOFF code (13H).

When the blank positions in the receive buffer are 2K bytes or more, the printer turns the

DTR signal to “High” level (READY) and sends an XON code (11H).

When there are no blank positions in the receive buffer, the printer discards data received

exceeding the receive buffer capacity, without storing it in the buffer. (After detecting the

XOFF code or BUSY signal, the host computer must stop transmission before the printer

receive buffer becomes full.)

The printer sends an XOFF code (13H) when the power is off.

The RTS signal is always “High”.

RTS Protocol

When initialized after the power is turned on, this printer turns the RTS signal to “High”

(READY).

The printer turns the RTS signal to “Low” (BUSY) when the blank positions in the receive

buffer are 1K bytes or less.

The printer turns the RTS signal to “High” (READY) when the blank positions in the receive

buffer are 2K bytes or more.

When there are no blank positions in the receive buffer, the printer discards data received

exceeding the receive buffer capacity, without storing it in the buffer. (After detecting the

BUSY signal, the host computer must stop transmission before the printer receive buffer

becomes full.)

The DTR signal is always “High” (READY).

- 5 -

(14) RS-232 Interface pin configuration

Host Function 9 Pin 25 Pin 9 Pin Printer Function

1 +5V

RxD 2 3 2 TxD

TxD 3 2 3 RxD

DTR 4 20 4 DSR

GND 5 7 5 GND

DSR 6 6 6 RDY

RTS 7 4 7 N/C

CTS 8 5 8 RDY

9 +5V

(15) Connector Pin Assignment and Signal Description

Pin No.

Signal

Name

Function Signal Direction

1 +5V Provide the power of 5V

2 TxD Transmit data Printer →

3 RxD Receive data ← Host

4 DSR Data set ready ← Host

5 GND General Ground

6 RDY Printer ready Printer →

7 N/C Not connected

8 RDY Printer ready Printer →

9 +5V Provide the power of 5V

- 6 -

3.2 PARALLEL INTERFACE

(1) Type : Centronics

(2) Mode : Conforms to IEEE1284 compatible mode

(3) Data Input Method : Parallel 8 bits (DATA1 ~ 8)

(4) Control Signals : ACK, BUSY, SELECT, DATA • STB, FAULT, PE, INIT (Not used),

AUTOFD (Not used), SELECTIN (Not used)

(5) Data Input Code : ASCII code

European character set 8 bit code

Graphics 8 bit code

(6) Receive Buffer : 515K bytes

(7) Connector : Printer

Amp. Japan 552742-1 or equivalent

DDK 57RE-40360-73B or equivalent

Cable

Amp. Japan 552470-1 or equivalent

DDK 57E-30360 or equivalent

- 7 -

(8) Connector Pin Diagram:

Pin No. Signal Name Pin No. Signal Name

1 DATA • STB 19 TWISTED PAIR GND (PIN1)

2 DATA 1 20 TWISTED PAIR GND (PIN2)

3 DATA 2 21 TWISTED PAIR GND (PIN3)

4 DATA 3 22 TWISTED PAIR GND (PIN4)

5 DATA 4 23 TWISTED PAIR GND (PIN5)

6 DATA 5 24 TWISTED PAIR GND (PIN6)

7 DATA 6 25 TWISTED PAIR GND (PIN7)

8 DATA 7 26 TWISTED PAIR GND (PIN8)

9 DATA 8 27 TWISTED PAIR GND (PIN9)

10 ACK 28 TWISTED PAIR GND (PIN10)

11 BUSY 29 TWISTED PAIR GND (PIN11)

12 PE 30 TWISTED PAIR GND (PIN31)

13 SELECT 31 INIT (Not used)

14 AUTOFD (Not used) 32 FAULT

15 NC 33 0V

16 0V 34 NC

17 CHASSIS GND 35 NC

18 +5V 36 SELECTIN (Not used)

18 1

36

19

- 8 -

4. KEY OPERATION FUNCTIONS

4.1 SYSTEM MODE (POWER UP WITH KEY PRESSED)

There are 6 LED light indications with following sequence.

(1) Solid orange indicates the printer has entered into system mode

(2) Green and red alternate

(3) Flashing orange

(4) Green and orange alternate

(5) Orange and red alternate

(6) Solid green

4.1.1 Firmware downloading mode

1) Release FEED key at LED light sequence (2) and push again immediately.

2) Copy the firmware file to printer parallel port by the following command is MS-DOS prompt

mode.

C:\>COPY XXXXXX.NEW /B LPT1:

3) The LED will change to green color and blinking every one-second. When firmware update is

completed, printer will reset automatically.

4.1.2 Auto call cancellation

1) Release FEED key at LED light sequence (3).

2) The printer will cancel Auto Call execution. (Refer to 6.3.24)

4.1.3 Parameter clearance

1) Release FEED key at LED light sequence (4).

2) The printer will restore to manufacturer’s default setting and reset automatically.

4.1.4 Sensor calibration

1) Install a label/tag roll with the sensor located at proper position.

2) Release FEED key at LED light sequence (5).

3) The printer will set the sensor property for the installed media and measures label length.

4.1.5 Self-test / Dump mode

1) Release FEED key at LED light sequence (6).

2) The printer will print self-test then enter the dump mode.

- 9 -

[Self-test printing]

a. Printing program version & check sum

b. Printing various parameters

Parameter Initial value

Print density fine adjustment 0

Print position fine adjustment 0 mm

Amount for finely the cut position 0 mm

Type of character code PC-850

Font of zero 0 (without slash)

Communication speed 9600 bps

Data length 8 bits

Stop bit length 1 bit

Parity NONE

Transmission control 2

Forward feed wait ON

Control code AUTO

Feed key function FEED

Euro code B0 H

X-coordinate adjustment 0 mm

Sensor selection Transmissive

4.2 ONLINE MODE FUNCTIONS

The online mode provides the following functions for issuing labels.

(1) Issuing labels (by external equipment interface commands)

(2) Paper feed (by the [FEED] key)

(3) Error indication

(4) Sensor selection

Transmissive sensor, reflective sensor and non-sensor mode are available.

To select the sensor for the media, turn on power to let printer online mode. Open printer cover,

the LED will be turned off. Press FEED key for over 5 seconds, and then release the button, then

printer will enter sensor selection mode.

In sensor selection mode, if LED is changed to green color and press FEED key again, then

reflective sensor is selected.

If LED is changed to orange color and press FEED key again, then non-sensor is selected.

If LED is changed to red color and press FEED key again, then transmissive sensor is selected.

- 10 -

5. TRANSMISSION SEQUENCE

This section describes the outline of the transmission sequence.

5.1 INITIALIZATION

Writable characters, logo, and PC interface commands must be stored before the label issue

operation.

(1) Storing writable characters and logo

NOTES: (1) The storage of PC commands is only performed if it is required.

(2) When the flash memory board is used, and the Memory board Format Command is not

sent before storing already stored writable characters or logos, memory will be taken up

with every such storing.

(3) When the flash memory board is used, and another operation (storing PC interface

commands or label issue operation) is performed after storing writable characters or

logos, the image buffer will be cleared automatically.

(4) If another storing operation does not take place after storing writable characters or

logos, the printer automatically enters the online mode (label issue operation) after

about 10 seconds. In this case, when the flash memory board is used, the image buffer

will be cleared automatically.

Power ON

<New>

Memory board

Format Command

Bit Map Writable

Character Command

Yes

(Add/change)

[ESC] J1: Formats the flash memory on the

memory board.

Completion of storing

all characters

Storing PC interface commands

Label issue operation

No

Yes

[ESC] XD: Stores writable characters or a

logo on the flash memory board.

No

- 11 -

(2) Storing PC interface commands

NOTES: (1) The storage of PC commands is only performed if it is required.

(2) When the flash memory card is used, and the Memory board Format Command is not

sent before storing already stored PC interface commands, memory will be taken up with

every such storing.

(3) When the flash memory board is used, and another operation (storing writable characters

or logos, label issue operation) is performed after storing PC interface commands, the

image buffer will be cleared automatically.

(4) Select commands to be stored as the occasion demands.

(5) If another storing operation does not take place after storing PC interface commands, the

printer enters the online mode (label issue operation) after about 10 seconds. In this

case, when the flash memory board is used, the image buffer will be cleared

automatically.

Power ON

<New>

Memory board

Format Command

Bit Map Font Data Command

No

Yes

(Add/change)

[ESC] J1: Formats the flash memory board.

Completion of

all storing

Storing writable characters or logos

Label issue operation

No

Yes

[ESC] XO: Declares the start of saving PC interface

commands.

Save Start Command

Label Size Set Command

Position Fine

Adjust Command

Print Density Fine

Adjust Command

Image Buffer Clear Command

Line Format Command

Bit Map Font Format Command

Outline Font Format Command

Bar Code Format Command

Save Terminate Command

[ESC] D: Sets the label size.

[ESC] AX: Adjusts the feed length, cut position, and

back feed length.

[ESC] AY: Adjusts the print density.

[ESC] C: Clears the image buffer.

[ESC] LC: Sets the line format and draws it.

[ESC] PC: Sets the bit map font format.

[ESC] PV: Sets the outline font format.

[ESC] XB: Sets the bar code format.

[ESC] RC: Draws data of the bit map font.

[ESC] XP: Declares the termination of saving PC

interface commands.

- 12 -

5.2 LABEL ISSUE OPERATION

An example of the label issue operation is described below.

(1) Where the Saved Data Call Command is not used:

NOTES: (1) When placing new paper, the Label Size Set Command and Feed Command must

always be sent. When using the same paper after the power is turned off and on, the

Label Size Set Command and Feed Command may be omitted.

(2) After the power is turned off and on, the Bit Map Font Format Command, the Outline

Font Format Command, and the Bar Code Format Command should be sent as

occasion demands because they are not protected in memory.

Power ON

Bit Map Font Data Command

Yes

Position Fine

Ad

j

ust Command

Print Density Fine

Ad

j

ust Command

Image Buffer Clear Command

Line Format Command

Bit Map Font Format Command

Outline Font Format Command

Bar Code Format Command

[ESC] D: Sets the label size.

[ESC] AX: Adjusts the feed length, cut position, and

back feed length.

[ESC] AY: Adjusts the print density.

[ESC] C: Clears the image buffer.

[ESC] LC: Sets the line format and draws it.

[ESC] PC: Sets the bit map font format.

[ESC] PV: Sets the outline font format.

[ESC] XB: Sets the bar code format.

[ESC] RC: Draws bit map font data.

Feed Command

[ESC] T: Feeds one sheet of paper and aligns it

with the first printing position.

Outline Font Data Command

[ESC] RV: Draws outline font data.

Bar Code Data Command

[ESC] RB: Draws bar code data.

Issue Command

[ESC] XS: Issues (prints) the label.

No

Yes

No

Yes

No

Power OFF

Label Size Set Command

Place paper

- 13 -

(2) Where the Saved Data Call Command is used:

NOTES: (1) When placing new paper, the Feed Command must always be sent. When using the

same paper after the power is turned off and on, the Feed Command may be omitted.

(2) If the option for “automatic call at power on” for the Saved Data Call Command has

previously been selected, the Saved Data Call Command may be omitted after the

power is turned off and on.

Power ON

Bit Map Font Data Command

Yes

Place paper

Saved Data Call Command

[ESC] XQ: Calls the label format stored in the flash

memory board.

[ESC] RC: Draws bit map font data.

Feed Command

[ESC] T: Feeds one sheet of paper and aligns it with

the first printing position.

Outline Font Data Command

[ESC] RV: Draws outline font data.

Bar Code Data Command

[ESC] RB: Draws bar code data.

Issue Command

[ESC] XS: Issues (prints) the label.

No

Yes

No

Power OFF

- 14 -

6. INTERFACE COMMANDS

6.1 OUTLINE OF COMMANDS

(1) Format of Interface command

The length from [ESC] to [LF] [NUL] must be as specified by each command.

There are the following three kinds of control codes:

ESC (1BH), LF (0AH), NUL (00H)

{ (7BH), | (7CH), } (7DH)

(2) How to use reference

Function Describes the outline of the function of the command.

Format Shows the format of the command.

The format designation method should conform to the following rules:

Each set of small letters (such as aa, bbbb) indicates a parameter item.

An item enclosed in parentheses may be omitted.

“…” indicates the repetition of an item.

Brackets and parentheses are used only in coding, and must not be transmitted

in practice.

Other symbols must always be inserted at the designated positions before being

transmitted.

Term Explains the term(s) used in the format.

“0 to 999” described in the entry range indicates that up to 3-digit variable-length

entry is allowed. (Entry of “001” or “009” is also possible.) “000 to 999” indicates

that entry must be fixed as 3 digits.

Explanation Explains the command in detail.

Note Supplementary explanation of the command.

Refer to Related commands

Examples Explains the command examples.

The above corresponds to the transfer of the following:

(3) Precautions

ESC Command & Data LF NUL

[

ESC

]

T20C30

[

LF

]

[

NUL

]

1B 54 30 30 43 33 32 0A 00

[ESC]

T 2 0 C 3 0 [LF] [NUL]

The commands and parameters described in this specification must always be used. If an

y

command or parameter other than those covered in this specification is used, the printer

operation will not be guaranteed. The commands must be used in the online mode. If an

y

command is transmitted in system mode, the printer will not operate. However, only the Reset

Command can be used.

- 15 -

NOTES:

1. If a command is not recognized as a command, it is ignored.

e.g.) [ESC] H, [ESC]AA, and so on.

2. If the number of digits of the parameter is specified, when the number of in put digits does not

match the specified number of digits, a command error occurs.

3. When a parameter is set to any character/value other than specified characters/values, a

command error occurs.

e.g.) In the case that a value should be set for parameter, “0001” is acceptable, however, “000A”

results in an error.

In the case that a character should be set for parameter, “A” is acceptable, however, “1” results in

an error.

4. If the value range of the parameter is specified, when any value beyond the range is entered, a

command error occurs. (Except for the D command)

5. When a parameter is missing, which cannot be omitted, a command error occurs.

6. The parameter should be set to either a value or a character, even if the parameter is defined as

“Ignore”.

e.g.) a : Ignore

If it is omitted, a command error occurs, except when the parameter is omissible.

If the number of digits of the parameter is specified, when the number of input digits does not

match the specified number of digits, a command error occurs.

7. When any value/character other than available values/characters for the parameter function is set,

a command error occurs.

e.g.) Parameter “e” for the LC command.

e: Type of line

0: Line

1: Rectangle

If “2” is set to parameter “e”, a command error occurs.

8. About D command

1) Parameter “aaaa”, “bbbb” and “cccc”

When any value lager than maximum value is entered for these three parameters, the entered

value is internally changed to the maximum value.

When any value smaller than minimum value is entered for these tree parameters, the entered

value is internally changed to the minimum value.

2) When “aaaa” is smaller than “cccc”, a command error occurs.

3) When “aaaa – cccc < 2mm”, it is internally changed to “cccc = aaaa – 2mm”.

- 16 -

6.2 LIST OF COMMANDS

(1) Commands related to setting

Label Size Set Command [ESC] D......................................17

(2) Commands related to fine adjustment

Position Fine Adjust Command [ESC] AX....................................22

Print Density Fine Adjust Command [ESC] AY....................................27

(3) Commands related to clear

Image Buffer Clear Command [ESC] C......................................28

Clear Area Command [ESC] XR ...................................29

(4) Commands related to drawing format setting

Line Format Command [ESC] LC....................................31

Bit Map Font Format Command [ESC] PC ...................................35

Outline Font Format Command [ESC] PV....................................49

Bar Code Format Command [ESC] XB....................................63

(5) Commands related to print data

Bit Map Font Data Command [ESC] RC...................................94

Outline Font Data Command [ESC] RV ...................................97

Bar Code Data Command [ESC] RB .................................100

(6) Commands related to issue and feed

Issue Command [ESC] XS..................................113

Feed Command [ESC] T....................................123

Eject Command [ESC] IB...................................128

Forward/Reverse Feed Command (Reserved for future) [ESC] U1, [ESC] U2.................129

(7) Commands related to writable characters

Storage Area Allocate Command [ESC] XF..................................131

Memory Card Format Command [ESC] J1...................................133

2-byte Writable Character Code Range Command [ESC] XE..................................134

Bit Map Writable Character Command [ESC] XD .................................135

(8) Commands related to graphics

Graphic Command [ESC] SG.................................146

(9) Commands related to PC command saving

Memory Card Format Command [ESC] J1...................................133

Save Start Command [ESC] XO.................................154

Save Terminate Command [ESC] XP..................................156

Saved Data Call Command [ESC] XQ.................................157

(10) Commands related to control

Reset Command [ESC] WR ................................158

Batch Reset Command [ESC] Z0..................................172

(11) Commands related to status

Status Request Command [ESC] WS ................................159

Receive Buffer Free Space Status Request Command [ESC] WB ................................160

Version Information Acquire Command [ESC] WV, [ESC] WI ...............162

(12) Commands related to printer information

Information Store Command [ESC] IG...................................165

Information Request Command [ESC] IR.................................. 166

(13) Commands related to parameter setting

Parameter Set Command [ESC] Z2;1...............................167

Fine Adjustment Value Set Command [ESC] Z2;2.............................. 170

La pagina sta caricando ...

Toshiba GC10-QM Manuale utente

Questo manuale è adatto anche per

Toshiba GC10-QM Manuale utente

in altre lingue

Documenti correlati

Altri documenti