Intermec 3400 Manuale utente

3400, 3440, and 3600

Bar Code Label Printer

P/N 065145-001

User’s Manual

Intermec Technologies Corporation

6001 36th Avenue West

P.O. Box 4280

Everett, WA 98203-9280

U.S. technical and service support: 1-800-755-5505

U.S. media supplies ordering information: 1-800-227-9947

Canadian technical and service support: 1-800-687-7043

Canadian media supplies ordering information: 1-800-267-6936

Outside U.S. and Canada: Contact your local Intermec service supplier.

The information contained herein is proprietary and is provided solely for the purpose of allowing

customers to operate and/or service Intermec manufactured equipment and is not to be released,

reproduced, or used for any other purpose without written permission of Intermec.

Information and specifications in this manual are subject to change without notice.

 1998 by Intermec Technologies Corporation

The word Intermec, the Intermec logo, JANUS, IRL, TRAKKER, Antares, Adara, Duratherm,

EZBuilder, Precision Print, PrintSet, Virtual Wedge, and CrossBar are trademarks of Intermec

Technologies Corporation.

The name Centronics is wholly owned by GENICOM Corporation.

IBM is a registered trademark of International Business Machines Corporation.

Throughout this manual, trademarked names may be used. Rather than put a trademark () symbol

in every occurrence of a trademarked name, we state that we are using the names only in an

editorial fashion, and to the benefit of the trademark owner, with no intention of infringement.

The software contained in the 3400, 3440, and 3600 Printers and the accompanying materials are

copyrighted. Unauthorized copying of the software, including software that has been modified,

merged, or included with other software, or the written materials is expressly forbidden without the

prior written consent of Intermec. All right, title, and interest in all copies of this software are and

shall at all times remain the sole and exclusive property of Intermec. Customers may be held legally

responsible for any copyright infringement that is caused or encouraged by their failure to abide by

these terms.

Contents

iii

Contents

Before You Begin vii

Warranty Information vii

Safety Summary vii

Warnings and Cautions viii

About This Manual ix

Other Intermec Manuals xi

Getting Started

Using This Manual 1-3

Getting to Know Your Printer 1-3

Preparing the Printer for Installation 1-5

Plugging In the Printer 1-5

Opening the Printer 1-6

Loading Media for Fanfold Printing 1-7

Printing the Hardware Configuration Test Label 1-9

What the Hardware Configuration Test Label Tells You 1-10

If a Hardware Configuration Test Label Does Not Print 1-10

Connecting the Printer to Your System 1-10

Connecting Your Printer to a PC 1-11

Connecting the Printer to a PC Serial Port 1-11

Connecting the Printer to a PC Parallel Port 1-12

Connecting Your Printer to a Network 1-12

Connecting the Printer to an AS/400 1-14

Connecting the Printer to a Mainframe 1-14

Cabling in Noisy Electrical Environments 1-14

Configuring the Serial Port for Communications 1-15

Verifying Printer Communications With Your System 1-18

Operating the Printer

Learning How to Operate the Printer 2-3

Understanding the Front Panel 2-3

Understanding the Front Panel LEDs 2-4

Using the Feed/Pause Button 2-5

1

2

3400, 3440, and 3600 Bar Code Label Printer User’s Manual

iv

Loading Media Into the Printer 2-6

Loading Roll Media for Straight-Through Printing 2-6

Loading Media for Self-Strip Printing 2-8

Loading Thermal Transfer Ribbon 2-10

Setting the Media Sensitivity Number 2-12

Setting the MSN for Intermec Media and Ribbon 2-13

Setting the MSN for Other Media and Ribbon 2-14

Communicating With the Printer 2-18

Using the PrintSet Software 2-18

Using Third-Party Software 2-18

Using Intermec Printer Language (IPL) Commands 2-18

Printing a Test Label 2-19

Maintaining the Printer

Inspecting the Printer 3-3

Tools for Cleaning the Printer 3-3

Maintenance Schedule 3-4

Cleaning the Printhead 3-6

Cleaning the Printer Covers 3-7

Cleaning the Drive Roller and Tear Bar 3-8

Cleaning the Media Guides and Media Path 3-9

Cleaning the Label Sensors 3-10

Troubleshooting

Troubleshooting Checklist 4-3

Printer Operation Problems 4-3

Print Quality Problems 4-5

Communication Problems and Preventing Data Loss 4-7

Optimizing Printer Performance

Optimizing and Maintaining Print Quality 5-3

Correcting Uneven Print Quality 5-3

3

4

5

Contents

v

Adjusting the Print Darkness 5-5

Adjusting the Label Mark Sensor 5-6

Using the Printer Memory Efficiently 5-8

How Is the Printer RAM Used? 5-8

Making the Most of Your RAM 5-9

Increasing Throughput 5-10

What Is an Image Band? 5-10

How Does the Image Bands Command Work? 5-10

Optimizing Print Speed and Image Band Setting 5-11

Optimizing Image Bands for Batch Printing 5-11

Using Test and Service Mode

Using Test and Service Mode Procedures 6-3

Printing Test Labels 6-5

Using Data Line Print 6-5

Performing Selective Transfer 6-6

Resetting the Memory on Your Printer 6-7

Setting Configuration Commands in Test and Service Mode 6-8

Setting the Number of Dot Increments 6-9

Adjusting the Label Rest Point 6-11

Setting Emulation Mode 6-13

Using Forms Adjust 6-14

X Forms Adjust 6-15

Y Forms Adjust 6-16

Specifications

Printer Specifications A-3

3400 Specifications A-4

3440 Specifications A-6

3600 Specifications A-8

Printer Options A-10

Memory Expansion and Fonts A-10

Communication Interface A-10

Finishers A-11

Bar Code Symbologies Supported A-13

6

A

3400, 3440, and 3600 Bar Code Label Printer User’s Manual

vi

Character Sets

International Character Sets B-3

Advanced Character Table B-3

Emulation Mode Character Table B-4

IBM Translation Character Table B-4

Code Page 850 Character Table B-5

Extended Character Sets B-6

Communications Reference

Communication Protocols C-3

Intermec Standard Protocol C-3

XON/XOFF Protocol (Software and Hardware Flow Control) C-4

XON/XOFF, No Status Protocol C-5

Polling Mode D C-5

Multi-Drop Protocol C-5

User-Defined Protocol C-6

Host Requirements C-7

Communications Boundaries C-7

Communications Interfaces C-7

RS-232 Serial Interface C-7

RS-422 Serial Interface C-8

RS-485 Serial Interface C-8

Printer Serial Port C-11

Full ASCII Table

Glossary

Index

B

C

D

G

I

HelvC

NugFont

Code39

Before You Begin

vii

Before You Begin

This section introduces you to standard warranty provisions, safety

precautions, warnings and cautions, document formatting conventions, and

sources of additional product information. A documentation roadmap is also

provided to guide you in finding the appropriate information.

Warranty Information

To receive a copy of the standard warranty provision for this product, contact

your local Intermec sales organization. In the U.S. call 1-800-755-5505, and in

Canada call 1-800-688-7043. Otherwise, refer to the Worldwide Sales & Service

list that was shipped with this manual for the address and telephone number of

your Intermec sales organization.

Safety Summary

Your safety is extremely important. Read and follow all warnings and cautions

in this book before handling and operating Intermec equipment. You can be

seriously injured, and equipment and data can be damaged if you do not follow

the safety warnings and cautions.

Do not repair or adjust alone Do not repair or adjust energized equipment alone

under any circumstances. Someone capable of providing first aid must always

be present for your safety.

First aid Always obtain first aid or medical attention immediately after an

injury. Never neglect an injury, no matter how slight it seems.

Resuscitation Begin resuscitation immediately if someone is injured and stops

breathing. Any delay could result in death. To work on or near high voltage,

you should be familiar with approved industrial first aid methods.

Energized equipment Never work on energized equipment unless authorized

by a responsible authority. Energized electrical equipment is dangerous.

Electrical shock from energized equipment can cause death. If you must

perform authorized emergency work on energized equipment, be sure that you

comply strictly with approved safety regulations.

3400, 3440, and 3600 Bar Code Label Printer User’s Manual

HelvC

NugFont

Code39

viii

Warnings and Cautions

The warnings and cautions in this manual use the following format.

Warning

A warning warns you of an operating procedure, practice, condition, or

statement that must be strictly observed to avoid death or serious injury to

the persons working on the equipment.

Avertissement

Un avertissement vous alerte d’une procédure de fonctionnement, d’une

méthode, d’un état ou d’un rapport qui doit être strictement respecté pour

éviter l’occurrence de mort ou de blessures graves aux personnes manupulant

l’équipement.

Caution

A caution alerts you to an operating procedure, practice, condition, or

statement that must be strictly observed to prevent equipment damage or

destruction, or corruption, or loss of data.

Conseil

Une précaution vous avertit d’une procédure de fonctionnement, d’une

méthode, d’un état ou d’un rapport qui doit être strictement respecté pour

empêcher l’endommagement ou la destruction de l’équipement, ou l’altération

ou la perte de données.

HelvC

NugFont

Code39

Before You Begin

ix

About This Manual

Analysts and programmers should use this manual to learn how to operate,

program, and connect the 3400, 3440, or 3600 printer to a network or system.

The first part of this manual tells you how to install, operate, maintain, and

troubleshoot your printer. The last part of the manual covers advanced features

of the 3400, 3440, and 3600 printers. A basic understanding of DOS,

programming, and data communications is necessary.

What You Will Find in This Manual

This table summarizes the information in each chapter of this manual:

For Information On Refer To

Installing the printer Chapter 1, “Getting Started.” Tells you how to plug in the

printer, load fanfold media, configure the serial port, and

print a configuration test label.

Operating the printer Chapter 2, “Operating the Printer.” Explains the printer front

panel, tells you how to load roll media, load ribbon, test for

communications, and download fonts.

Routine maintenance Chapter 3, “Maintaining the Printer.” Shows how to maintain

the printer.

Troubleshooting Chapter 4, “Troubleshooting.” Instructs how to clear error

messages and troubleshoot programming or configuration

problems.

Improving printer

performance

Chapter 5, “Optimizing Printer Performance.” Tells you how

to fine-tune the printer to increase processing time.

Test and Service

features

Chapter 6, “Using Test and Service Mode.” Provides

information on using Test and Service mode to print test

labels, perform Test and Service mode procedures, and

configure DIP switch settings.

Specifications Appendix A.

Character sets Appendix B.

Communications Appendix C.

Full ASCII chart Appendix D.

3400, 3440, and 3600 Bar Code Label Printer User’s Manual

HelvC

NugFont

Code39

x

Terms and Conventions

Listed below are special terms and conventions used throughout the manual.

Refer to the glossary for a complete list of terms found in this manual.

Terms

“Printer” refers to a 3400, 3440, or 3600 bar code label printer.

“Media” is the label stock on which the printer prints labels.

“Host” refers to a personal computer or other computer that communicates

with the printer.

A “symbol” or “bar code symbol” consists of alphanumeric characters encoded

in a bar code format.

Conventions

The following conventions are used throughout this manual for operating

procedures and descriptions of the printer.

• Feed/Pause refers to the Feed/Pause button on the printer front panel.

• Downloaded commands appear in the order that you enter them into the

printer with the following conventions:

Convention Description

< > Angle brackets < > enclose mnemonic representations of ASCII control

characters. For example, <ETX> represents the ASCII “End of Text”

control character.

data

Italic text represents variable data, which you must replace with a real

value. For example,

n

signifies a variable for which you must designate a

constant value.

[

data

] Italic text within brackets represents optional data.

Ctrl Bold text represents a key on your keypad. For example, Tab represents

the Tab key and M represents the letter M key.

Ctrl-Z When two keys are joined with a dash, press them simultaneously. For

example, if you see the command Ctrl-C, press the two keys at the same

time.

E3;F3

Type all characters that appear in the Courier font by pressing an

individual key on the keypad.

HelvC

NugFont

Code39

Before You Begin

xi

Other Intermec Manuals

The following manuals provide additional information about equipment that

works with your bar code label printer. You can order these manuals or find

them on the Intermec web site at www.intermec.com/manuals/manuals.htm.

Manual Intermec Part Number

IPL Programming Reference Manual

066396

9154 Multi-Drop Line Controller System Manual

048517

9161B Installation Manual

049572

9180 Network Controller User’s Manual

054292

Data Communications Reference Manual

044737

RF System User’s Manual

053574

The Bar Code Book

051241

Getting Started

1

HelvC

NugFont

Code39

Getting Started

1-3

1

This chapter introduces the 3400, 3440, and 3600 printer and explains how to get your

new printer running for the first time.

Using This Manual

Use this manual to learn about your Intermec 3400, 3440, or 3600 printer.

Although the three printers are almost identical in form and function, they do

have some small differences.

Throughout this manual you will find these icons beside information that

pertains to a specific printer model.

Icon

Description

Identifies

information that is

unique to the 200

dpi 3400 printer.

Identifies

information that is

unique to the 400

dpi 3440 printer.

Identifies

information that is

unique to the 200

dpi 3600 printer.

Note: The 3440 printer appears in most of the illustrations in this manual.

Getting to Know Your Printer

Features of your printer include:

•

Support for direct thermal and thermal transfer printing applications.

Chapters 1 and 2 explain how to load both types of media.

•

An internal self-strip with integral liner takeup. See Chapter 2, “Operating

the Printer,” for more information.

•

An easy-to-use software application called PrintSet. PrintSet makes

configuring your printer, downloading fonts and graphics, and printing a

test label effortless.

•

Minimal supervision and maintenance.

•

Support for user-supplied fonts. You can easily download and print user-

supplied fonts. See the PrintSet software application or the

IPL Programming

Reference Manual

for more information.

•

Support for TrueType. You can easily download and print TrueType fonts.

See the PrintSet software application or the

IPL Programming Reference

Manual

for more information.

Use the following figures to familiarize yourself with your printer.

3400, 3440, and 3600 Bar Code Label Printer User’s Manual

HelvC

**

1233*

FG 8pt Italic

1-4

Front View

Power/Data

3440

Alert

Feed/Pause

Empty/Pause

Intermec

Media access

door

Feed/Pause

button

Empty/Pause

button

Alert LED

Power/Data

LED

Media

cover

Media

window

3XXXU.002

Back View

1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8

3XXXU.003

O

I

Media

cover

Fanfold media

access slot

AC power cord

receptacle

Serial communications

port

On/Off

switch

Optional I/O

board port

Darkness adjust

control

DIP switches

Media

window

Several options are available for use with your printer. See Appendix A for

complete descriptions of these options.

HelvC

NugFont

Code39

Getting Started

1-5

1

Preparing the Printer for Installation

Before connecting your printer to your data collection system, you need to

•

plug in the printer.

•

open the printer and load media.

•

print a configuration test label.

Plugging In the Printer

The back of your printer contains the AC power receptacle, the serial

communications port, the On/Off switch, and two banks of DIP switches.

To plug in the printer

1. Turn the On/Off switch to the off position.

2. Make sure you set the DIP switches to their factory default settings.

Top Bank

Set switch 1 on (

I

). Set switches 2 through 8 off (O).

Bottom Bank

Set switches 1 through 8 off (O).

For a description of the DIP switch settings, see “Configuring the Serial Port

for Communications” later in this chapter.

O

I

O

I

1 2 3 4 5 6 7 8

O

1 2 3 4 5 6 7 8

I

O

I

1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8

O

I

3XXXU.004

1

2

3

3400, 3440, and 3600 Bar Code Label Printer User’s Manual

HelvC

**

1233*

FG 8pt Italic

1-6

3. Plug the AC power cord into the receptacle at the rear of the printer. Plug

the other end of the power cord into a grounded wall outlet or surge

protector.

4. Turn the On/Off switch to the on position. When you power on the printer,

the Power On LED lights, the Empty/Pause LED flashes, and the platen

roller advances. The yellow Empty/Pause LED then stays on steady

because you have not loaded media yet.

Opening the Printer

You need to open the printer every time you load media or perform

maintenance procedures.

To open the printer

1. Place the fingers of your right hand between the two notches on the lower

edge of the media cover (the media cover release) and pull the bottom of the

media cover away from the base of the printer.

2. Grasp the front of the media cover with your left hand and lift the front of

the media cover upward to release it from the printer frame.

3. Lift the media cover away from the top of the printer.

3XXXU.005

Power/Data

3440

Alert

Feed/Pause

Empty/Pause

IntermecIntermec

1

3

2

HelvC

NugFont

Code39

Getting Started

1-7

1

Loading Media for Fanfold Printing

Use the sample of fanfold media provided in the Media Envelope to complete

the following procedures. In fanfold printing, you place a stack of fanfold

media at the rear of the printer and feed it into the printer through a slot in the

rear cover. Refer to Chapter 2, “Operating the Printer,” for instructions on

loading rolls of media.

To load media for fanfold printing

1. Open the printer.

2. Disengage the printhead by rotating the head lift lever clockwise until it

releases.

3. Move the supply roll retainer by turning it counterclockwise and sliding it

to the outer end of the supply post.

4. Place the fanfold media slightly lower than the slot in the printer back

cover. Line the (box of) fanfold media up with the label path through the

printer. Insert media through the slot at the rear of the printer and thread it

over the supply roll post.

5. To allow easy access to the media path, pull down on the lower media

guide. Make sure that the edge guide is slid all the way to the outer edge of

the edge guide plate.

6. Insert the fanfold media through the printer mechanism as shown in the

illustration on the next page. The front edge of the media should pass over

the tear bar and through the label dispense opening in the media cover. The

fanfold media should pass over the supply roll post.

7. Release the lower media guide and adjust the edge guide to position the

media firmly against the inside wall of the printer.

8. Slide the supply roll retainer up to the edge of the fanfold media and turn

the supply roll retainer clockwise until it locks firmly in place securing the

media against the inside wall of the printer.

9. Engage the printhead by rotating the head lift lever counterclockwise until

it locks.

10. Close the printer by reversing the directions for removing the cover.

3400, 3440, and 3600 Bar Code Label Printer User’s Manual

HelvC

**

1233*

FG 8pt Italic

1-8

Loading Media for Fanfold Printing

3XXXU.006

Media access

slot

Fanfold

media

1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8

O

I

➤

Lower

media guide

Head lift

lever

Supply

roll

post

Edge

guide

Supply

roll

retainer

11. Press Feed/Pause to advance one label through the printer and out the label

opening in the front cover. The printer is now ready to print the

configuration test label. The yellow Empty/Pause LED goes out.

Note: If the yellow Empty/Pause LED does not go out, press Feed/Pause a second time

and then reload the media and try again if the Empty/Pause LED still does not go out.

Note: For your convenience, refer to the label with directions for loading media. This

label is located on the inside of the media cover.

La pagina sta caricando ...

Intermec 3400 Manuale utente

Questo manuale è adatto anche per

Intermec 3400 Manuale utente

in altre lingue

Documenti correlati

Altri documenti