Datalogic C-BOX 410 Guida d'installazione

C-BOX 400/410

Installation Manual

C-BOX 400/410

INSTALLATION MANUAL

DATALOGIC S.p.A.

Via Candini 2

40012 - Lippo di Calderara di Reno

Bologna - Italy

C-BOX 400/410

Ed.: 03/2006

Datalogic S.p.A. reserves the right to make modifications and improvements without prior notification.

Datalogic shall not be liable for technical or editorial errors or omissions contained herein, nor for incidental or

consequential damages resulting from the use of this material.

Product names mentioned herein are for identification purposes only and may be trademarks and or

registered trademarks of their respective companies.

821001010 (Rev 01)

CONTENTS

GUIDE TO INSTALLATION ........................................................................ iv

GENERAL VIEW .......................................................................................... v

SAFETY PRECAUTIONS............................................................................ ix

Power Supply................................................................................................ix

Safety Notes .................................................................................................ix

WEEE Compliance ....................................................................................... x

1 GENERAL FEATURES ................................................................................ 1

1.1 Description.................................................................................................... 1

1.1.1 DeviceNet ..................................................................................................... 2

2 INSTALLATION............................................................................................ 3

2.1 Package Contents......................................................................................... 3

2.2 Opening the Device ...................................................................................... 4

2.3 Mechanical Installation.................................................................................. 5

2.4 Electrical Connections and Setup ................................................................. 7

2.4.1 Power Supply................................................................................................ 8

2.4.2 System Wiring............................................................................................. 10

2.4.3 Scanner Chassis Grounding Jumper Settings ............................................ 12

2.4.4 OM4000 Jumper Settings ........................................................................... 12

2.5 DeviceNet Connections and Setup ............................................................. 13

2.5.1 DeviceNet Node Address (MAC ID) and Baud Rate Selection ................... 13

2.5.2 DeviceNet Connector (M12 Male External Sealed Micro Connector) ......... 13

2.5.3 Connection to a DeviceNet Network ........................................................... 14

2.5.4 C-BOX 4X0 Configuration for DeviceNet Slave Node................................. 15

2.6 Configuration Switch and 9-Pin Internal Connector ............................................ 16

2.7 Barcode Scanner Requirements................................................................. 18

2.8 Operating Modes ........................................................................................ 18

2.8.1 GET/TEST/SEND Functions....................................................................... 19

2.8.2 LED Indicators ............................................................................................ 21

2.9 Special Notes for Matrix Reader Setup....................................................... 23

2.9.1 Preparing C-Box 4x0 for Matrix Reader Communication ............................ 23

2.9.2 Matrix Reader Configuration Using VisiSet™ ............................................. 24

2.9.3 Completing C-Box 4x0 Configuration for Matrix-1000™ Readers............... 25

3 TECHNICAL FEATURES........................................................................... 26

iii

GUIDE TO INSTALLATION

The following can be used as a checklist to verify all of the steps necessary for

complete installation of the C-BOX 4X0.

1) Read all information in the section "Safety Precautions" at the beginning of this

manual.

2) Correctly position and mount the C-BOX 4X0 within the reach of the barcode

scanner cable, according to the information in paragraph 2.3.

3) Provide correct system cabling according to the signals necessary for your

application and DeviceNet settings (see all sub-paragraphs under 2.4).

The installation is now complete.

iv

GENERAL VIEW

C-BOX 400

2

3

4

5

1

Figure A

25-pin scanner connector

Compression Connectors

Shield Nut

1

2

3

DeviceNet Connector

4

Cover screws (4)

5

v

C-BOX 410

2

1

Figure B

LCD display

Keypad

1

2

vi

C-BOX 400/410

1

2

5

3

4

7

8

9

6

Figure C - Cover Inside

LCD contrast trimmer

1

2

Power on (PWR) LED

3

Transmission (TX) LED

4

Module status (MS) LEDs

5

Network status (NS) LEDs

6

7

8

Configuration switch

Node address selectors

Baud rate selector

9

Warning (WL) LED

vii

C-BOX 400/410

8

654

3

2

1

7

9

10

Figure E - Bottom Inside

Power on switch

1

2

Scanner chassis grounding selector

3

Spring clamp terminal blocks

5

4

GET button

TEST button

6

SEND button

7

8

9

A

uxiliary port connector

OM4000 jumpers

Warning LED

10

Power polarity error LED

viii

SAFETY PRECAUTIONS

POWER SUPPLY

ATTENTION: READ THIS INFORMATION BEFORE INSTALLING THE PRODUCT

- This product is intended to be installed by Qualified Personnel only.

The C-BOX 4X0 is intended to be supplied either by a UL Listed NEC Class 2 power

source, or a UL Listed ITE Limited Power Source (LPS), rated 10-30 V dc, minimum

0.5 A.

See par. 2.4.1 for correct power supply connections.

SAFETY NOTES

Observe the general rules for DeviceNet components when planning the C-BOX

installation.

Observe the guidelines in the DeviceNet specifications. DeviceNet is a trademark of

Open DeviceNet Vendor Association, Inc. (ODVA). Please refer to ODVA

(www.odva.org) for further details.

Please observe the following to avoid risk to personnel and damage to equipment

and to ensure that the C-BOX 4X0 functions correctly:

Safety Regulations Observe the guidelines in the VDE 0100 regulations for

handling electrical components,

Observe the applicable safety and accident prevention

regulations.

The C-BOX must only be installed or uninstalled by

qualified technical personnel with appropriate electro-

technical qualifications.

Bus Cable Bus wiring should only take place using DeviceNet cable.

The high data transfer rates can only be guaranteed with

the correct cable type.

Cable Lengths Refer to the manual for the DeviceNet master and to the

ODVA documentation for information on maximum cable

lengths for DeviceNet.

ix

Terminating Resistors Two 121 Ohm, 1% Metal Film, ¼ Watt terminating

resistors should be installed at each side of the DeviceNet

trunk line (not at the end of a drop line or in a node). If the

bus is incorrectly terminated, this can lead to errors in data

transfer or bus failure. Please refer to ODVA

documentation for further details.

Bus Connectors It is recommended to use only commercially available

DeviceNet connectors for connecting the bus.

When connecting up the C-BOX 4X0, it is recommended to observe the guidelines in

the VDE 0100 regulations for handling electrical equipment.

WEEE COMPLIANCE

x

GENERAL FEATURES

1

1 GENERAL FEATURES

1.1 DESCRIPTION

The C-BOX 4X0 is a connection box which converts RS232 communications to

DeviceNet. It is available in two models:

C-BOX 400, without display,

C-BOX 410, with a LCD display.

It operates as a DeviceNet “Group 2 Only Slave” using the predefined Master/Slave

connection set. The Polled, Bit Strobe and Change of State (COS) protocol types are

available.

It can be used as an accessory of the Datalogic scanners to perform the following

functions:

• Connect an RS232 scanner/reader to a DeviceNet network.

• Facilitate the connection of the scanner signals using a spring clamp connector.

• Get the scanner configuration and store it in memory. *

• Force the scanner to the Test operating mode. *

• Send the configuration stored in memory to the scanner. *

• In the C-BOX 410, visualize the data packet sent by the scanner on the LCD.

The C-BOX 400 / C-BOX 410 mechanical dimensions are 167 x 115 x 61 mm (6.57 x

4.53 x 2.40 in.). The C-BOX 400 weighs about 470 g (16.50 oz); the C-BOX 410

weighs about 530 g (18.70 oz).

Electrical connection is provided through spring clamp terminal blocks inside the

C-BOX 4X0.

The scanner is connected to the C-BOX 4X0 through a 25-pin connector placed on

the left side of the housing.

A 9-pin connector placed inside the C-BOX 4X0 facilitates connection between an

external PC and the auxiliary serial interface of the scanner.

The external M12 male connector is used to connect the C-BOX 4X0 to a DeviceNet

network.

* Function not compatible with Matrix-2000™ or Matrix-1000™.

1

C-BOX 400/410

1

A dedicated shield nut offers the possibility to further increase the C-BOX 4X0 noise

immunity by simply connecting the ground. The fixing screw type is 4-40 UNC, 1/8

inch.

1.1.1 DeviceNet

DeviceNet is a low level network that provides connections between simple industrial

devices (sensors, actuators) and higher level devices (controllers), and eliminates

expensive hardwiring.

It allows the transport of control oriented information associated with low level

devices and the transport of other information which is indirectly related to the system

being controlled, such as configuration parameters.

DeviceNet is a standard open network allowing the interchangeability of simple

devices while making interconnectivity of more complex devices.

The DeviceNet communication link is based on a broadcast oriented communication

protocol: the Controller Area Network (CAN) for Media Access Control and Physical

Signaling.

CAN defines the syntax or form of the data movement.

DeviceNet is a trademark of Open DeviceNet Vendor Association, Inc. (ODVA).

Please refer to ODVA (www.odva.org) for further details.

2

INSTALLATION

2

2 INSTALLATION

2.1 PACKAGE CONTENTS

Verify that the C-BOX 4X0 and all the parts supplied with the equipment are present

and intact when opening the packaging; the list of parts includes:

1) C-BOX 4X0

2) Installation manual

3) C-BOX 4X0 configuration CD-ROM

4) 2 mounting screws

3

1

2

4

Figure 1 - C-BOX 4X0 Package Contents

3

C-BOX 400/410

2

2.2 OPENING THE DEVICE

To install the C-BOX 4X0 or during normal maintenance, it is necessary to open it by

unscrewing the four cover screws:

CAUTION

The C-BOX 4X0 must be disconnected from the power supply

during this operation.

C-BOX 4X0

Figure 2 - Opening the C-BOX 4X0

It is possible to perform the following operations:

• Proceed with the cable connections (see paragraph 2.4.2).

• Set the DeviceNet Node Address (MAC ID) selection on the rotary switches.

• Set the DeviceNet Baud Rate on the specific rotary switch.

• Mount the C-BOX 4X0 to a wall or panel.

4

INSTALLATION

2

2.3 MECHANICAL INSTALLATION

The diagram below gives the overall dimensions of the C-BOX 4X0 and may be used

for its installation.

Figure 3 - Overall Dimensions

5

C-BOX 400/410

2

C-BOX 4X0 can be installed to operate in different positions. The two screw holes

inside the housing of the C-BOX 4X0 are for mechanical fixture (Figure 4).

To mount the C-BOX 4X0:

1) Open the C-BOX 4X0 by unscrewing the 4 cover screws. If necessary, using the

two mounting holes inside the device as a pattern, mark the panel with an

appropriate object and then drill two holes in the panel.

2) Align the C-BOX 4X0 and insert two screws and screw them into the panel until

tight (see Figure 4).

Figure 4 - Mounting C-BOX 4X0

6

INSTALLATION

2

2.4 ELECTRICAL CONNECTIONS AND SETUP

The following figure shows the typical layout.

P

G

E

GR

D

NORE

DER

D

DeviceNet

MASTER

C-BOX 4X0

SCANNER

System

Cables

Figure 5 – System Layout

NOTE

Matrix readers are not compatible with the WinHost configuration

program. For Matrix reader setup first read par. 2.9 for details.

A PC can be connected to the C-BOX 4X0 (and consequently to the scanner

auxiliary interface) through the internal 9-pin connector. This allows monitoring of the

data transmitted by the scanner or configuration through the WinHost utility (see the

scanner Installation Manual for more details). The scanner auxiliary interface signals

are also available on the internal spring clamp connectors.

After making system cabling and switch settings (see sub-paragraphs under 2.4),

connect the scanner to the 25-pin connector on the left side of the C-BOX 4X0

housing.

Switch ON the C-BOX 4X0 power switch (see Figure 6).

By default, after power on, an automatic connection procedure takes place between

the C-BOX 4X0 and the scanner. During this phase, requiring a few seconds, the

warning LED is turned ON. Once the procedure had been completed successfully,

the warning LED is turned OFF.

7

C-BOX 400/410

2

NOTE

Autoconnection is not compatible with Matrix readers and must be

disabled in the C-BOX 4x0 configuration. See par. 2.9 for details.

To disable this automatic connection procedure, refer to WinHost Help Online.

After system functioning has been verified, close the C-BOX 4X0 using the 4 cover

screws making sure the rubber seal is fitted correctly between the parts of the

housing.

2.4.1 Power Supply

Power is supplied to the C-BOX 4X0 through the pins provided on the spring clamp

connector.

The power switch (see Figure 6) switches the power supply ON or OFF for both the

C-BOX 4X0 and the connected scanner.

ON

OFF

S1

Figure 6 - Power Switch ON/OFF Positions

C-BOX

1

2

VS

GND

USER INTERFACE

GND

V+ (10 - 30 Vdc)

Figure 7 - Power Supply Connections

The power supply must be between 10 and 30 Vdc only.

8

La pagina sta caricando ...

Datalogic C-BOX 410 Guida d'installazione

Questo manuale è adatto anche per

Datalogic C-BOX 410 Guida d'installazione

in altre lingue

Documenti correlati

Altri documenti