Intel BLKD945GCLF2 Manuale utente

Intel® Desktop Board D945GCLF2

Product Guide

Order Number: E40804-002

Revision History

Revision Revision History Date

-001 First release of the Intel

®

Desktop Board D945GCLF2

Product Guide

July 2008

-002 Second release of the Intel

®

Desktop Board D945GCLF2

Product Guide

December 2008

If an FCC declaration of conformity marking is present on the board, the following statement applies:

FCC Declaration of Conformity

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

For questions related to the EMC performance of this product, contact:

Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124, 1-800-628-8686

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause harmful interference to

radio communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the interference by

one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment to an outlet on a circuit other than the one to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Any changes or modifications to the equipment not expressly approved by Intel Corporation could void the

user’s authority to operate the equipment.

Tested to comply with FCC standards for home or office use.

Canadian Department of Communications Compliance Statement

This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set

out in the Radio Interference Regulations of the Canadian Department of Communications.

Le présent appareil numerique német pas de bruits radioélectriques dépassant les limites applicables aux

appareils numériques de la classe B prescrites dans le Réglement sur le broullage radioélectrique édicté par

le ministére des Communications du Canada.

Disclaimer

Information in this document is provided in connection with Intel

®

products. No license, express or implied,

by estoppel or

otherwise, to any intellectual property rights is granted by this document. Except as provided

in Intel’s Terms and Conditions of Sale for such products, Intel assumes no liability whatsoever, and Intel

disclaims any express or implied warranty, relating to sale and/or use of Intel products including liability or

warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent,

copyright or other intellectual property right. Intel products are not intended for use in medical, life saving,

or life sustaining applications. Intel may make changes to specifications and product descriptions at any

time, without notice.

Intel Desktop Board D945GCLF2 may contain design defects or errors known as errata which may cause the

product to deviate from published specifications. Current characterized errata are available on request.

Contact your local Intel sales office or your distributor to obtain the latest specifications and before placing

your product order.

This product incorporates copyright protection technology that is protected by U.S. patents and other

intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision*,

and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision.

Reverse engineering or disassembly is prohibited.

Copies of documents which have an ordering number and are referenced in this document, or other Intel

literature, may be obtained from Intel Corporation by going to the World Wide Web site at:

http://www.intel.com/ or by calling 1-800-548-4725.

Intel, the Intel logo, and Intel Atom are trademarks of Intel Corporation in the U. S. and other countries.

* Other names and brands may be claimed as the property of others.

iii

Preface

This Product Guide gives information about board layout, component installation, and

regulatory requirements for Intel

®

Desktop Board D945GCLF2.

Intended Audience

The Product Guide is intended for technically qualified personnel. It is not intended for

general audiences.

Intended Uses

All Intel

®

Desktop Boards are evaluated as Information Technology Equipment (I.T.E.)

for use in personal computers (PC) for installation in homes, offices, schools, computer

rooms, and similar locations. The suitability of this product for other PC or embedded

non-PC applications or other environments, such as medical, industrial, alarm systems,

test equipment, etc. may not be supported without further evaluation by Intel.

Document Organization

The chapters in this Product Guide are arranged as follows:

1 Desktop Board Features: a summary of product features

2 Installing and Replacing Desktop Board Components: instructions on how to install

the Desktop Board and other hardware components

3 Updating the BIOS: a description of how to update the BIOS

A BIOS Error Messages: information about BIOS error messages and beep codes

B Regulatory Compliance: safety and EMC regulations and product certifications

Conventions

The following conventions are used in this manual:

CAUTION

Cautions warn the user about how to prevent damage to hardware or loss of data.

NOTE

Notes call attention to important information.

Intel Desktop Board D945GCLF2 Product Guide

iv

Terminology

The table below gives descriptions to some common terms used in the product guide.

Term Description

GB Gigabyte (1,073,741,824 bytes)

GHz Gigahertz (one billion hertz)

KB Kilobyte (1024 bytes)

MB Megabyte (1,048,576 bytes)

Mbit Megabit (1,048,576 bits)

MHz Megahertz (one million hertz)

v

Contents

1 Desktop Board Features

Desktop Board Components.................................................................................10

Processor..........................................................................................................12

Main Memory.....................................................................................................12

Intel

®

945GC Express Chipset..............................................................................13

S-Video Support ................................................................................................13

Onboard Audio Subsystem ..................................................................................13

Input/Output (I/O) Controller ..............................................................................14

LAN Subsystem .................................................................................................15

LAN Subsystem Software.............................................................................15

LAN Status LEDs.........................................................................................15

Hi-Speed USB 2.0 Support ..................................................................................16

Enhanced IDE Interface ......................................................................................16

Serial ATA.........................................................................................................16

Expandability.....................................................................................................16

BIOS................................................................................................................17

IDE Auto Configuration................................................................................17

PCI Auto Configuration ................................................................................17

Security Passwords.....................................................................................17

Power Management Features ...............................................................................18

ACPI.........................................................................................................18

Hardware Support ......................................................................................18

Power Connectors ...............................................................................18

Fan Headers .......................................................................................18

+5 V Standby Power Indicator LED ........................................................18

LAN Wake Capabilities..........................................................................19

Wake from USB ..................................................................................19

Wake from PS/2 Keyboard/Mouse..........................................................20

PME# Wakeup Support ........................................................................20

Battery.............................................................................................................20

Real-Time Clock.................................................................................................20

2 Installing and Replacing Desktop Board Components

Before You Begin ...............................................................................................21

Installation Precautions.......................................................................................22

Prevent Power Supply Overload ....................................................................22

Observe Safety and Regulatory Requirements.................................................22

Installing the I/O Shield ......................................................................................23

Installing and Removing the Desktop Board ...........................................................24

Installing and Removing Memory..........................................................................25

Installing DIMMs ........................................................................................25

Removing DIMMs........................................................................................27

Connecting the IDE Cable....................................................................................27

Connecting the Serial ATA (SATA) Cable................................................................29

Connecting Internal Headers................................................................................30

Connecting the Front Panel Audio Header.......................................................31

Connecting the S/PDIF Connector .................................................................31

Intel Desktop Board D945GCLF2 Product Guide

vi

Connecting to the Front Panel Header............................................................32

Connecting the Hi-Speed USB 2.0 Headers.....................................................32

Connecting a Chassis Fan....................................................................................33

Connecting Power Supply Cables ..........................................................................34

Setting the BIOS Configuration Jumper .................................................................35

Clearing Passwords.....................................................................................36

Replacing the Battery .........................................................................................37

3 Updating the BIOS

Updating the BIOS with the Intel

®

Express BIOS Update Utility.................................43

Updating the BIOS with the Iflash Memory Update Utility.........................................43

Obtaining the BIOS Update File ....................................................................43

Updating the BIOS with the Iflash Memory Update Utility .................................44

Recovering the BIOS...................................................................................44

A BIOS Error Messages

BIOS Front-panel Power LED Blink Codes ..............................................................45

BIOS Beep Codes...............................................................................................45

BIOS Error Messages..........................................................................................46

B Regulatory Compliance

Safety Standards ...............................................................................................47

Place Battery Marking .................................................................................47

European Union Declaration of Conformity Statement..............................................48

Product Ecology Statements ................................................................................49

Recycling Considerations .............................................................................49

Lead-free 2LI/Pb-free 2LI Board ...................................................................52

Restriction of Hazardous Substances (RoHS) ..................................................53

European Union RoHS..........................................................................53

China RoHS ........................................................................................53

EMC Regulations ................................................................................................55

Ensure Electromagnetic Compatibility (EMC) Compliance..................................56

Product Certifications..........................................................................................57

Board-Level Certification Markings ................................................................57

Chassis and Component Certifications............................................................58

Contents

vii

Figures

1. Intel Desktop Board D945GCLF2 Components...................................................10

2. Back Panel Audio Connectors .........................................................................14

3. LAN Status LEDs ..........................................................................................15

4. Location of the Standby Power Indicator ..........................................................19

5. Installing the I/O Shield ................................................................................23

6. Intel Desktop Board D945GCLF2 Mounting Screw Holes .....................................24

7. Use DDR2 DIMMs .........................................................................................25

8. Installing a DIMM .........................................................................................26

9. Connecting the IDE Cable ..............................................................................28

10. Connecting the Serial ATA Cable .....................................................................29

11. Internal Headers ..........................................................................................30

12. Location of the Chassis Fan Header .................................................................33

13. Connecting a 2 x 10 or 2 x 12 Power Supply Cable ............................................34

14. BIOS Configuration Jumper Block....................................................................35

15. Removing the Battery ...................................................................................41

16. Intel Desktop Board D945GCLF2 China RoHS Material Self Declaration Table.........54

Tables

1. Feature Summary.......................................................................................... 9

2. Intel Desktop Board D945GCLF2 Components...................................................11

3. LAN Status LEDs ..........................................................................................15

4. Front Panel Audio Header Signal Names for HD Audio ........................................31

5. S/PDIF Connector Signal Names .....................................................................31

6. Front Panel Header Signal Names ...................................................................32

7. Hi-Speed USB 2.0 Headers Signal Names.........................................................32

8. Jumper Settings for the BIOS Setup Program Modes..........................................36

9. BIOS Front-panel Power LED Blink Codes.........................................................45

10. BIOS Beep Codes .........................................................................................45

11. BIOS Error Messages ....................................................................................46

12. Safety Standards..........................................................................................47

13. Lead-Free Second Level Interconnect Marks .....................................................52

14. China RoHS Environmentally Friendly Use Period Mark .......................................53

15. EMC Regulations...........................................................................................55

16. Product Certification Markings ........................................................................57

Intel Desktop Board D945GCLF2 Product Guide

viii

9

1 Desktop Board Features

This chapter briefly describes the main features of Intel

®

Desktop Board D945GCLF2.

Table 1 summarizes the features of the Desktop Board.

Table 1. Feature Summary

Form Factor

Mini-ITX (171.45 millimeters [6.75 inches] x 171.45 millimeters

[6.75 inches])

Processor

Dual-Core Intel

®

Atom

™

processor

Main Memory

• One 240-pin SDRAM Dual Inline Memory Module (DIMM) socket

• 533 MHz single channel DDR2 SDRAM interface

• Supports up to 2 GB of system memory

Chipset

Intel

®

945GC Express Chipset consisting of:

• Intel

®

82945GC Express Chipset Graphics and Memory Controller Hub

(GMCH)

• Intel

®

82801GB I/O Controller Hub (ICH7)

Graphics

• Integrated graphics via the

Intel

®

Graphics Media Accelerator 950

(Intel

®

GMA 950)

• Back panel S-Video output via a Chrontel CH7021A SDTV/HDTV Encoder

Audio

• RealTek* ALC662 audio codec

• Support for Intel

®

High Definition Audio

• Support for 6-channel (5.1) audio

• Onboard S/PDIF connector

Expansion

Capabilities

One PCI* bus add-in card connector

Peripheral

Interfaces

• Up to eight USB 2.0 ports

― Four ports routed to the back panel

― Four ports routed to two onboard USB headers

• One IDE interface with ATA-100/66 support (two devices)

• Two Serial ATA (3.0 Gb/s) interfaces

• One VGA connector

• S-Video output

• One parallel port

• One serial port

• PS/2* keyboard and mouse ports

BIOS

• Intel

®

BIOS

• Support for SMBIOS

• Intel

®

Rapid BIOS Boot

• Intel

®

Express BIOS Update

LAN Support

• 10/100/1000 Mb/s (Gigabit) Ethernet LAN Subsystem

Power Management

• Support for Advanced Configuration and Power Interface (ACPI)

• Wake on USB, PCI, PS/2, LAN, and front panel

Supported

Operating Systems

• Microsoft Windows Vista* Home Basic Edition

• Microsoft Windows Vista Home Basic 64-bit edition

• Microsoft Windows* XP Professional

• Microsoft Windows XP Professional x64 Edition

• Microsoft Windows XP Home

For more information about Intel Desktop Board D945GCLF2, including the Technical

Product Specification (TPS), BIOS updates, and device drivers, go to

http://support.intel.com/support/motherboards/desktop/

.

Intel Desktop Board D945GCLF2 Product Guide

10

Desktop Board Components

Figure 1 shows the location of the major components on Intel Desktop Board

D945GCLF2.

Figure 1. Intel Desktop Board D945GCLF2 Components

Desktop Board Features

11

Table 2. Intel Desktop Board D945GCLF2 Components

Label Description

A PCI bus add-in card connector

B Front panel audio header

C Back panel connectors

D 12 V processor core voltage connector (2 x 2)

E Rear fan (3-pin) header

F Processor

G DDR 2 DIMM connector

H Main power connector (2 x 12)

I IDE connector

J Serial ATA connectors (2)

K Front panel header

L Battery

M BIOS configuration jumper

N Hi-speed USB 2.0 header

O S/PDIF connector (3-pin)

Intel Desktop Board D945GCLF2 Product Guide

12

Processor

CAUTION

Failure to use an appropriate power supply and/or not connecting the 12 V (2 x 2)

power connector to the Desktop Board may result in damage to the board, or the

system may not function properly.

Intel Desktop Board D945GCLF2 includes a Dual-Core Intel Atom processor. The

processor is soldered to the Desktop Board and is not customer upgradeable.

Main Memory

NOTE

To be fully compliant with all applicable Intel

®

SDRAM memory specifications, the

board should be populated with DIMMs that support the Serial Presence Detect (SPD)

data structure. If your DIMMs do not support SPD, you will see a notification to this

effect on the screen at power up. The BIOS will attempt to configure the memory

controller for normal operation.

The Desktop Board has one 240-pin Double Data Rate 2 (DDR2) SDRAM Dual Inline

Memory Module (DIMM) connector with gold-plated contacts. It supports:

• 533 MHz unbuffered, non-registered DDR2 DIMMs

• Serial Presence Detect (SPD) memory only

• Non-ECC memory

• Up to 2 GB of memory

For the latest list of tested memory, go to

http://support.intel.com/support/motherboards/desktop/

.

Desktop Board Features

13

Intel

®

945GC Express Chipset

The Intel 945GC Express Chipset consists of the following devices:

• Intel 82945GC Express Chipset Graphics and Memory Controller Hub (GMCH)

• Intel 82801GB I/O Controller Hub (ICH7)

The GMCH component provides interfaces to the processor, memory, and the DMI

interconnect. This component also provides integrated graphics capabilities via the

Intel

®

Graphics Media Accelerator 950 (Intel

®

GMA 950).

The ICH7 is a centralized controller for the board’s I/O paths. For more information

about the Intel 945GC Express Chipset, go to

http://www.intel.com/design/chipsets/express_flyer.htm

.

S-Video Support

The board supports S-Video output via a 7-pin back panel connector that provides

both 4-pin S-Video and a Composite Video signal.

Onboard Audio Subsystem

Intel Desktop Board D945GCLF2 has a 6-channel (5.1) onboard audio subsystem that

includes a Realtek ALC662 audio codec.

The audio subsystem features:

• Intel High Definition Audio interface

• Advanced jack sense, for the back panel connectors, that enables the audio codec

to recognize the device that is connected to an audio port and retask the connector

via the audio driver.

• S/N (signal-to-noise) ratio: 95 dB

• Microphone input supporting:

― Stereo microphone

― Microphone boost

The subsystem includes the following headers and connectors:

• Onboard S/PDIF connector (3-pin)

• Front panel audio header, including functionality for:

― Line out

― Microphone in

• Back panel audio connectors that are configurable through the audio device

drivers:

― Line in/retasking jack

― Line out/retasking jack

― Mic in/retasking jack

Intel Desktop Board D945GCLF2 Product Guide

14

Figure 2 shows the default assignment of the back panel audio connectors.

Item

Description

A Line In

B Line Out

C Mic In

Figure 2. Back Panel Audio Connectors

NOTE

The back panel audio line out connector is designed to power headphones or amplified

speakers only. Poor audio quality occurs if passive (non-amplified) speakers are

connected to this output.

Related Links:

Go to the following locations for more information about:

• Audio drivers and utilities http://support.intel.com/support/motherboards/desktop/

• Installing a front panel audio solution (page 31)

Input/Output (I/O) Controller

The super I/O controller features the following:

• One serial port

• One parallel port with Extended Capabilities Port (ECP) and Enhanced Parallel Port

(EPP) support

• Serial IRQ interface compatible with serialized IRQ support for PCI systems

• PS/2-style mouse and keyboard interfaces

• Intelligent power management, including a programmable wake up event interface

• PCI power management support

Desktop Board Features

15

LAN Subsystem

The LAN, based on the RealTek RTL8111C Ethernet Controller, provides the following

functions:

• 10/100/1000 Mb/s Gigabit Ethernet LAN

• Support for RJ-45 connector with status indicator LEDs

• Programmable transit threshold

• Configurable EEPROM that contains the MAC address

LAN Subsystem Software

For LAN software and drivers, refer to the Intel Desktop D945GCLF2 link on Intel’s

World Wide Web site at http://support.intel.com/support/motherboards/desktop

.

LAN Status LEDs

Two LEDs are built into the RJ-45 LAN connector located on the back panel (see

Figure 3). These LEDs indicate the operating states of the LAN.

Figure 3. LAN Status LEDs

Table 3 describes the LED states when the board is powered up and the LAN

subsystem is operating.

Table 3. LAN Status LEDs

LED LED Color LED State Indicates

Activity (A) Green Blinking LAN activity is occurring.

N/A Off 10 Mbits/s data rate is selected.

Green On (steady state) 100 Mbits/s data rate is selected.

Speed (B)

Yellow On (steady state) 1000 Mbits/s data rate is selected.

Intel Desktop Board D945GCLF2 Product Guide

16

Hi-Speed USB 2.0 Support

NOTE

Computer systems that have an unshielded cable attached to a USB port might not

meet FCC Class B requirements, even if no device or a low-speed USB device is

attached to the cable. Use a shielded cable that meets the requirements for a

full-speed USB device.

The Desktop Board supports up to eight USB 2.0 ports (four ports routed to the back

panel and four ports routed to two onboard USB 2.0 headers). The USB 2.0 ports are

backward compatible with USB 1.1 devices. USB 1.1 devices will function normally at

USB 1.1 speeds.

USB 2.0 support requires both an operating system and drivers that fully support

USB 2.0 transfer rates. Disabling Hi-Speed USB in the BIOS reverts all USB 2.0 ports

to USB 1.1 operation. This may be required to accommodate operating systems that

do not support USB 2.0.

Enhanced IDE Interface

The IDE interface handles the exchange of information between the processor and

peripheral devices such as hard disks and optical drives inside the computer. The

interface supports:

• Up to two IDE devices (such as hard drives)

• ATAPI-style devices (such as CD-ROM or DVD drives)

• Older PIO Mode devices

• Ultra DMA-33/66/100 modes

Serial ATA

The Desktop Board supports two Serial ATA channels (3.0 Gb/s), connecting one

device per channel.

Expandability

The Desktop Board supports one PCI add-in card.

Desktop Board Features

17

BIOS

The BIOS provides the Power-On Self-Test (POST), the BIOS Setup program, the PCI

and IDE auto-configuration utilities, and the video BIOS.

IDE Auto Configuration

If you install an IDE device (such as a hard drive) in your computer, the auto-

configuration utility in the BIOS automatically detects and configures the device for

your computer. You do not need to run the BIOS Setup program after installing an

IDE device. You can override the auto-configuration options by specifying manual

configuration in the BIOS Setup program.

PCI Auto Configuration

If you install a PCI add-in card in your computer, the PCI auto-configuration utility in

the BIOS automatically detects and configures the resources (IRQs, DMA channels,

and I/O space) for that add-in card. You do not need to run the BIOS Setup program

after you install a PCI add-in card.

Security Passwords

The BIOS includes security features that restrict whether the BIOS Setup program can

be accessed and who can boot the computer. A supervisor password and a user

password can be set for the BIOS Setup and for booting the computer, with the

following restrictions:

• The supervisor password gives unrestricted access to view and change all Setup

options. If only the supervisor password is set, pressing <Enter> at the password

prompt of Setup gives the user restricted access to Setup.

• If both the supervisor and user passwords are set, you must enter either the

supervisor password or the user password to access Setup. Setup options are then

available for viewing and changing depending on whether the supervisor or user

password was entered.

• Setting a user password restricts who can boot the computer. The password

prompt is displayed before the computer is booted. If only the supervisor

password is set, the computer boots without asking for a password. If both

passwords are set, you can enter either password to boot the computer.

For instructions on resetting the password, see Clearing Passwords on page 36.

Intel Desktop Board D945GCLF2 Product Guide

18

Power Management Features

Power management is implemented at several levels, including:

• Advanced Configuration and Power Interface (ACPI)

• Hardware support:

― Power connectors

― Fan headers

― +5 V standby power indicator LED

― LAN Wake capabilities

― Wake from USB

― Wake from PS/2 keyboard/mouse

― PME# wakeup support

ACPI

ACPI gives the operating system direct control over the power management and Plug

and Play functions of a computer. The use of ACPI with the Desktop Board requires an

operating system that provides full ACPI support.

Hardware Support

Power Connectors

The Desktop Board has two power connectors. See Figure 13 on page 34 for the

location of the power connectors.

Fan Headers

The Desktop Board has a 3-pin MCH fan header and a 3-pin chassis fan header. See

Figure 12 on page 33 for the location of the chassis fan header.

+5 V Standby Power Indicator LED

CAUTION

If the AC power has been switched off and the standby power indicator is still lit,

disconnect the power cord before installing or removing any devices connected to the

board. Failure to do so could damage the board and any attached devices.

The Desktop Board’s standby power indicator, shown in Figure 4, is lit when there is

standby power to the system. This includes the DIMM socket and the PCI bus

connector, even though the computer appears to be off.

Desktop Board Features

19

Figure 4. Location of the Standby Power Indicator

For more information on standby current requirements for the Desktop Board, refer to

the Technical Product Specification on the Intel Desktop D945GCLF2 web page at

http://support.intel.com/support/motherboards/desktop/

LAN Wake Capabilities

CAUTION

For LAN wake capabilities, the 5 V standby line for the power supply must be capable

of delivering adequate +5 V standby current. Failure to provide adequate standby

current when using this feature can damage the power supply.

LAN wakeup capabilities enable remote wake-up of the computer through a network.

The LAN subsystem monitors network traffic and upon detecting a Magic Packet*

frame, it asserts a wake-up signal that powers up the computer.

Wake from USB

NOTE

Wake from USB requires the use of a USB peripheral that supports wake from USB.

USB bus activity wakes the computer from an ACPI S3 state.

Intel Desktop Board D945GCLF2 Product Guide

20

Wake from PS/2 Keyboard/Mouse

PS/2 keyboard/mouse activity wakes the computer from the ACPI S1, S3, S4, and S5

states.

PME# Wakeup Support

When the PME# signal on the PCI bus is asserted, the computer wakes from the ACPI

S1, S3, S4, and S5 states.

Battery

A battery on the Desktop Board keeps the values in CMOS RAM and the clock current

when the computer is turned off. Go to page 37 for instructions on how to replace the

battery.

Real-Time Clock

The Desktop Board has a time-of-day clock and 100-year calendar. The battery on the

Desktop Board keeps the clock current when the computer is turned off.

La pagina sta caricando ...

Intel BLKD945GCLF2 Manuale utente

Questo manuale è adatto anche per

Intel BLKD945GCLF2 Manuale utente

in altre lingue

Documenti correlati

Altri documenti