Intel BLKD945GCLF2 Manuale utente

Categoria
Schede madri
Tipo
Manuale utente
Intel® Desktop Board D945GCLF2
Product Guide
Order Number: E40804-002
Revision History
Revision Revision History Date
-001 First release of the Intel
®
Desktop Board D945GCLF2
Product Guide
July 2008
-002 Second release of the Intel
®
Desktop Board D945GCLF2
Product Guide
December 2008
If an FCC declaration of conformity marking is present on the board, the following statement applies:
FCC Declaration of Conformity
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
For questions related to the EMC performance of this product, contact:
Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124, 1-800-628-8686
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment to an outlet on a circuit other than the one to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications to the equipment not expressly approved by Intel Corporation could void the
user’s authority to operate the equipment.
Tested to comply with FCC standards for home or office use.
Canadian Department of Communications Compliance Statement
This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set
out in the Radio Interference Regulations of the Canadian Department of Communications.
Le présent appareil numerique német pas de bruits radioélectriques dépassant les limites applicables aux
appareils numériques de la classe B prescrites dans le Réglement sur le broullage radioélectrique édicté par
le ministére des Communications du Canada.
Disclaimer
Information in this document is provided in connection with Intel
®
products. No license, express or implied,
by estoppel or
otherwise, to any intellectual property rights is granted by this document. Except as provided
in Intel’s Terms and Conditions of Sale for such products, Intel assumes no liability whatsoever, and Intel
disclaims any express or implied warranty, relating to sale and/or use of Intel products including liability or
warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent,
copyright or other intellectual property right. Intel products are not intended for use in medical, life saving,
or life sustaining applications. Intel may make changes to specifications and product descriptions at any
time, without notice.
Intel Desktop Board D945GCLF2 may contain design defects or errors known as errata which may cause the
product to deviate from published specifications. Current characterized errata are available on request.
Contact your local Intel sales office or your distributor to obtain the latest specifications and before placing
your product order.
This product incorporates copyright protection technology that is protected by U.S. patents and other
intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision*,
and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision.
Reverse engineering or disassembly is prohibited.
Copies of documents which have an ordering number and are referenced in this document, or other Intel
literature, may be obtained from Intel Corporation by going to the World Wide Web site at:
http://www.intel.com/ or by calling 1-800-548-4725.
Intel, the Intel logo, and Intel Atom are trademarks of Intel Corporation in the U. S. and other countries.
* Other names and brands may be claimed as the property of others.
Copyright © 2008, Intel Corporation. All rights reserved.
iii
Preface
This Product Guide gives information about board layout, component installation, and
regulatory requirements for Intel
®
Desktop Board D945GCLF2.
Intended Audience
The Product Guide is intended for technically qualified personnel. It is not intended for
general audiences.
Intended Uses
All Intel
®
Desktop Boards are evaluated as Information Technology Equipment (I.T.E.)
for use in personal computers (PC) for installation in homes, offices, schools, computer
rooms, and similar locations. The suitability of this product for other PC or embedded
non-PC applications or other environments, such as medical, industrial, alarm systems,
test equipment, etc. may not be supported without further evaluation by Intel.
Document Organization
The chapters in this Product Guide are arranged as follows:
1 Desktop Board Features: a summary of product features
2 Installing and Replacing Desktop Board Components: instructions on how to install
the Desktop Board and other hardware components
3 Updating the BIOS: a description of how to update the BIOS
A BIOS Error Messages: information about BIOS error messages and beep codes
B Regulatory Compliance: safety and EMC regulations and product certifications
Conventions
The following conventions are used in this manual:
CAUTION
Cautions warn the user about how to prevent damage to hardware or loss of data.
NOTE
Notes call attention to important information.
Intel Desktop Board D945GCLF2 Product Guide
iv
Terminology
The table below gives descriptions to some common terms used in the product guide.
Term Description
GB Gigabyte (1,073,741,824 bytes)
GHz Gigahertz (one billion hertz)
KB Kilobyte (1024 bytes)
MB Megabyte (1,048,576 bytes)
Mbit Megabit (1,048,576 bits)
MHz Megahertz (one million hertz)
v
Contents
1 Desktop Board Features
Desktop Board Components.................................................................................10
Processor..........................................................................................................12
Main Memory.....................................................................................................12
Intel
®
945GC Express Chipset..............................................................................13
S-Video Support ................................................................................................13
Onboard Audio Subsystem ..................................................................................13
Input/Output (I/O) Controller ..............................................................................14
LAN Subsystem .................................................................................................15
LAN Subsystem Software.............................................................................15
LAN Status LEDs.........................................................................................15
Hi-Speed USB 2.0 Support ..................................................................................16
Enhanced IDE Interface ......................................................................................16
Serial ATA.........................................................................................................16
Expandability.....................................................................................................16
BIOS................................................................................................................17
IDE Auto Configuration................................................................................17
PCI Auto Configuration ................................................................................17
Security Passwords.....................................................................................17
Power Management Features ...............................................................................18
ACPI.........................................................................................................18
Hardware Support ......................................................................................18
Power Connectors ...............................................................................18
Fan Headers .......................................................................................18
+5 V Standby Power Indicator LED ........................................................18
LAN Wake Capabilities..........................................................................19
Wake from USB ..................................................................................19
Wake from PS/2 Keyboard/Mouse..........................................................20
PME# Wakeup Support ........................................................................20
Battery.............................................................................................................20
Real-Time Clock.................................................................................................20
2 Installing and Replacing Desktop Board Components
Before You Begin ...............................................................................................21
Installation Precautions.......................................................................................22
Prevent Power Supply Overload ....................................................................22
Observe Safety and Regulatory Requirements.................................................22
Installing the I/O Shield ......................................................................................23
Installing and Removing the Desktop Board ...........................................................24
Installing and Removing Memory..........................................................................25
Installing DIMMs ........................................................................................25
Removing DIMMs........................................................................................27
Connecting the IDE Cable....................................................................................27
Connecting the Serial ATA (SATA) Cable................................................................29
Connecting Internal Headers................................................................................30
Connecting the Front Panel Audio Header.......................................................31
Connecting the S/PDIF Connector .................................................................31
Intel Desktop Board D945GCLF2 Product Guide
vi
Connecting to the Front Panel Header............................................................32
Connecting the Hi-Speed USB 2.0 Headers.....................................................32
Connecting a Chassis Fan....................................................................................33
Connecting Power Supply Cables ..........................................................................34
Setting the BIOS Configuration Jumper .................................................................35
Clearing Passwords.....................................................................................36
Replacing the Battery .........................................................................................37
3 Updating the BIOS
Updating the BIOS with the Intel
®
Express BIOS Update Utility.................................43
Updating the BIOS with the Iflash Memory Update Utility.........................................43
Obtaining the BIOS Update File ....................................................................43
Updating the BIOS with the Iflash Memory Update Utility .................................44
Recovering the BIOS...................................................................................44
A BIOS Error Messages
BIOS Front-panel Power LED Blink Codes ..............................................................45
BIOS Beep Codes...............................................................................................45
BIOS Error Messages..........................................................................................46
B Regulatory Compliance
Safety Standards ...............................................................................................47
Place Battery Marking .................................................................................47
European Union Declaration of Conformity Statement..............................................48
Product Ecology Statements ................................................................................49
Recycling Considerations .............................................................................49
Lead-free 2LI/Pb-free 2LI Board ...................................................................52
Restriction of Hazardous Substances (RoHS) ..................................................53
European Union RoHS..........................................................................53
China RoHS ........................................................................................53
EMC Regulations ................................................................................................55
Ensure Electromagnetic Compatibility (EMC) Compliance..................................56
Product Certifications..........................................................................................57
Board-Level Certification Markings ................................................................57
Chassis and Component Certifications............................................................58
Contents
vii
Figures
1. Intel Desktop Board D945GCLF2 Components...................................................10
2. Back Panel Audio Connectors .........................................................................14
3. LAN Status LEDs ..........................................................................................15
4. Location of the Standby Power Indicator ..........................................................19
5. Installing the I/O Shield ................................................................................23
6. Intel Desktop Board D945GCLF2 Mounting Screw Holes .....................................24
7. Use DDR2 DIMMs .........................................................................................25
8. Installing a DIMM .........................................................................................26
9. Connecting the IDE Cable ..............................................................................28
10. Connecting the Serial ATA Cable .....................................................................29
11. Internal Headers ..........................................................................................30
12. Location of the Chassis Fan Header .................................................................33
13. Connecting a 2 x 10 or 2 x 12 Power Supply Cable ............................................34
14. BIOS Configuration Jumper Block....................................................................35
15. Removing the Battery ...................................................................................41
16. Intel Desktop Board D945GCLF2 China RoHS Material Self Declaration Table.........54
Tables
1. Feature Summary.......................................................................................... 9
2. Intel Desktop Board D945GCLF2 Components...................................................11
3. LAN Status LEDs ..........................................................................................15
4. Front Panel Audio Header Signal Names for HD Audio ........................................31
5. S/PDIF Connector Signal Names .....................................................................31
6. Front Panel Header Signal Names ...................................................................32
7. Hi-Speed USB 2.0 Headers Signal Names.........................................................32
8. Jumper Settings for the BIOS Setup Program Modes..........................................36
9. BIOS Front-panel Power LED Blink Codes.........................................................45
10. BIOS Beep Codes .........................................................................................45
11. BIOS Error Messages ....................................................................................46
12. Safety Standards..........................................................................................47
13. Lead-Free Second Level Interconnect Marks .....................................................52
14. China RoHS Environmentally Friendly Use Period Mark .......................................53
15. EMC Regulations...........................................................................................55
16. Product Certification Markings ........................................................................57
Intel Desktop Board D945GCLF2 Product Guide
viii
9
1 Desktop Board Features
This chapter briefly describes the main features of Intel
®
Desktop Board D945GCLF2.
Table 1 summarizes the features of the Desktop Board.
Table 1. Feature Summary
Form Factor
Mini-ITX (171.45 millimeters [6.75 inches] x 171.45 millimeters
[6.75 inches])
Processor
Dual-Core Intel
®
Atom
processor
Main Memory
One 240-pin SDRAM Dual Inline Memory Module (DIMM) socket
533 MHz single channel DDR2 SDRAM interface
Supports up to 2 GB of system memory
Chipset
Intel
®
945GC Express Chipset consisting of:
Intel
®
82945GC Express Chipset Graphics and Memory Controller Hub
(GMCH)
Intel
®
82801GB I/O Controller Hub (ICH7)
Graphics
Integrated graphics via the
Intel
®
Graphics Media Accelerator 950
(Intel
®
GMA 950)
Back panel S-Video output via a Chrontel CH7021A SDTV/HDTV Encoder
Audio
RealTek* ALC662 audio codec
Support for Intel
®
High Definition Audio
Support for 6-channel (5.1) audio
Onboard S/PDIF connector
Expansion
Capabilities
One PCI* bus add-in card connector
Peripheral
Interfaces
Up to eight USB 2.0 ports
Four ports routed to the back panel
Four ports routed to two onboard USB headers
One IDE interface with ATA-100/66 support (two devices)
Two Serial ATA (3.0 Gb/s) interfaces
One VGA connector
S-Video output
One parallel port
One serial port
PS/2* keyboard and mouse ports
BIOS
Intel
®
BIOS
Support for SMBIOS
Intel
®
Rapid BIOS Boot
Intel
®
Express BIOS Update
LAN Support
10/100/1000 Mb/s (Gigabit) Ethernet LAN Subsystem
Power Management
Support for Advanced Configuration and Power Interface (ACPI)
Wake on USB, PCI, PS/2, LAN, and front panel
Supported
Operating Systems
Microsoft Windows Vista* Home Basic Edition
Microsoft Windows Vista Home Basic 64-bit edition
Microsoft Windows* XP Professional
Microsoft Windows XP Professional x64 Edition
Microsoft Windows XP Home
For more information about Intel Desktop Board D945GCLF2, including the Technical
Product Specification (TPS), BIOS updates, and device drivers, go to
http://support.intel.com/support/motherboards/desktop/
.
Intel Desktop Board D945GCLF2 Product Guide
10
Desktop Board Components
Figure 1 shows the location of the major components on Intel Desktop Board
D945GCLF2.
Figure 1. Intel Desktop Board D945GCLF2 Components
Desktop Board Features
11
Table 2. Intel Desktop Board D945GCLF2 Components
Label Description
A PCI bus add-in card connector
B Front panel audio header
C Back panel connectors
D 12 V processor core voltage connector (2 x 2)
E Rear fan (3-pin) header
F Processor
G DDR 2 DIMM connector
H Main power connector (2 x 12)
I IDE connector
J Serial ATA connectors (2)
K Front panel header
L Battery
M BIOS configuration jumper
N Hi-speed USB 2.0 header
O S/PDIF connector (3-pin)
Intel Desktop Board D945GCLF2 Product Guide
12
Processor
CAUTION
Failure to use an appropriate power supply and/or not connecting the 12 V (2 x 2)
power connector to the Desktop Board may result in damage to the board, or the
system may not function properly.
Intel Desktop Board D945GCLF2 includes a Dual-Core Intel Atom processor. The
processor is soldered to the Desktop Board and is not customer upgradeable.
Main Memory
NOTE
To be fully compliant with all applicable Intel
®
SDRAM memory specifications, the
board should be populated with DIMMs that support the Serial Presence Detect (SPD)
data structure. If your DIMMs do not support SPD, you will see a notification to this
effect on the screen at power up. The BIOS will attempt to configure the memory
controller for normal operation.
The Desktop Board has one 240-pin Double Data Rate 2 (DDR2) SDRAM Dual Inline
Memory Module (DIMM) connector with gold-plated contacts. It supports:
533 MHz unbuffered, non-registered DDR2 DIMMs
Serial Presence Detect (SPD) memory only
Non-ECC memory
Up to 2 GB of memory
For the latest list of tested memory, go to
http://support.intel.com/support/motherboards/desktop/
.
Desktop Board Features
13
Intel
®
945GC Express Chipset
The Intel 945GC Express Chipset consists of the following devices:
Intel 82945GC Express Chipset Graphics and Memory Controller Hub (GMCH)
Intel 82801GB I/O Controller Hub (ICH7)
The GMCH component provides interfaces to the processor, memory, and the DMI
interconnect. This component also provides integrated graphics capabilities via the
Intel
®
Graphics Media Accelerator 950 (Intel
®
GMA 950).
The ICH7 is a centralized controller for the board’s I/O paths. For more information
about the Intel 945GC Express Chipset, go to
http://www.intel.com/design/chipsets/express_flyer.htm
.
S-Video Support
The board supports S-Video output via a 7-pin back panel connector that provides
both 4-pin S-Video and a Composite Video signal.
Onboard Audio Subsystem
Intel Desktop Board D945GCLF2 has a 6-channel (5.1) onboard audio subsystem that
includes a Realtek ALC662 audio codec.
The audio subsystem features:
Intel High Definition Audio interface
Advanced jack sense, for the back panel connectors, that enables the audio codec
to recognize the device that is connected to an audio port and retask the connector
via the audio driver.
S/N (signal-to-noise) ratio: 95 dB
Microphone input supporting:
Stereo microphone
Microphone boost
The subsystem includes the following headers and connectors:
Onboard S/PDIF connector (3-pin)
Front panel audio header, including functionality for:
Line out
Microphone in
Back panel audio connectors that are configurable through the audio device
drivers:
Line in/retasking jack
Line out/retasking jack
Mic in/retasking jack
Intel Desktop Board D945GCLF2 Product Guide
14
Figure 2 shows the default assignment of the back panel audio connectors.
Item
Description
A Line In
B Line Out
C Mic In
Figure 2. Back Panel Audio Connectors
NOTE
The back panel audio line out connector is designed to power headphones or amplified
speakers only. Poor audio quality occurs if passive (non-amplified) speakers are
connected to this output.
Related Links:
Go to the following locations for more information about:
Audio drivers and utilities http://support.intel.com/support/motherboards/desktop/
Installing a front panel audio solution (page 31)
Input/Output (I/O) Controller
The super I/O controller features the following:
One serial port
One parallel port with Extended Capabilities Port (ECP) and Enhanced Parallel Port
(EPP) support
Serial IRQ interface compatible with serialized IRQ support for PCI systems
PS/2-style mouse and keyboard interfaces
Intelligent power management, including a programmable wake up event interface
PCI power management support
Desktop Board Features
15
LAN Subsystem
The LAN, based on the RealTek RTL8111C Ethernet Controller, provides the following
functions:
10/100/1000 Mb/s Gigabit Ethernet LAN
Support for RJ-45 connector with status indicator LEDs
Programmable transit threshold
Configurable EEPROM that contains the MAC address
LAN Subsystem Software
For LAN software and drivers, refer to the Intel Desktop D945GCLF2 link on Intel’s
World Wide Web site at http://support.intel.com/support/motherboards/desktop
.
LAN Status LEDs
Two LEDs are built into the RJ-45 LAN connector located on the back panel (see
Figure 3). These LEDs indicate the operating states of the LAN.
Figure 3. LAN Status LEDs
Table 3 describes the LED states when the board is powered up and the LAN
subsystem is operating.
Table 3. LAN Status LEDs
LED LED Color LED State Indicates
Activity (A) Green Blinking LAN activity is occurring.
N/A Off 10 Mbits/s data rate is selected.
Green On (steady state) 100 Mbits/s data rate is selected.
Speed (B)
Yellow On (steady state) 1000 Mbits/s data rate is selected.
Intel Desktop Board D945GCLF2 Product Guide
16
Hi-Speed USB 2.0 Support
NOTE
Computer systems that have an unshielded cable attached to a USB port might not
meet FCC Class B requirements, even if no device or a low-speed USB device is
attached to the cable. Use a shielded cable that meets the requirements for a
full-speed USB device.
The Desktop Board supports up to eight USB 2.0 ports (four ports routed to the back
panel and four ports routed to two onboard USB 2.0 headers). The USB 2.0 ports are
backward compatible with USB 1.1 devices. USB 1.1 devices will function normally at
USB 1.1 speeds.
USB 2.0 support requires both an operating system and drivers that fully support
USB 2.0 transfer rates. Disabling Hi-Speed USB in the BIOS reverts all USB 2.0 ports
to USB 1.1 operation. This may be required to accommodate operating systems that
do not support USB 2.0.
Enhanced IDE Interface
The IDE interface handles the exchange of information between the processor and
peripheral devices such as hard disks and optical drives inside the computer. The
interface supports:
Up to two IDE devices (such as hard drives)
ATAPI-style devices (such as CD-ROM or DVD drives)
Older PIO Mode devices
Ultra DMA-33/66/100 modes
Serial ATA
The Desktop Board supports two Serial ATA channels (3.0 Gb/s), connecting one
device per channel.
Expandability
The Desktop Board supports one PCI add-in card.
Desktop Board Features
17
BIOS
The BIOS provides the Power-On Self-Test (POST), the BIOS Setup program, the PCI
and IDE auto-configuration utilities, and the video BIOS.
IDE Auto Configuration
If you install an IDE device (such as a hard drive) in your computer, the auto-
configuration utility in the BIOS automatically detects and configures the device for
your computer. You do not need to run the BIOS Setup program after installing an
IDE device. You can override the auto-configuration options by specifying manual
configuration in the BIOS Setup program.
PCI Auto Configuration
If you install a PCI add-in card in your computer, the PCI auto-configuration utility in
the BIOS automatically detects and configures the resources (IRQs, DMA channels,
and I/O space) for that add-in card. You do not need to run the BIOS Setup program
after you install a PCI add-in card.
Security Passwords
The BIOS includes security features that restrict whether the BIOS Setup program can
be accessed and who can boot the computer. A supervisor password and a user
password can be set for the BIOS Setup and for booting the computer, with the
following restrictions:
The supervisor password gives unrestricted access to view and change all Setup
options. If only the supervisor password is set, pressing <Enter> at the password
prompt of Setup gives the user restricted access to Setup.
If both the supervisor and user passwords are set, you must enter either the
supervisor password or the user password to access Setup. Setup options are then
available for viewing and changing depending on whether the supervisor or user
password was entered.
Setting a user password restricts who can boot the computer. The password
prompt is displayed before the computer is booted. If only the supervisor
password is set, the computer boots without asking for a password. If both
passwords are set, you can enter either password to boot the computer.
For instructions on resetting the password, see Clearing Passwords on page 36.
Intel Desktop Board D945GCLF2 Product Guide
18
Power Management Features
Power management is implemented at several levels, including:
Advanced Configuration and Power Interface (ACPI)
Hardware support:
Power connectors
Fan headers
+5 V standby power indicator LED
LAN Wake capabilities
Wake from USB
Wake from PS/2 keyboard/mouse
PME# wakeup support
ACPI
ACPI gives the operating system direct control over the power management and Plug
and Play functions of a computer. The use of ACPI with the Desktop Board requires an
operating system that provides full ACPI support.
Hardware Support
Power Connectors
The Desktop Board has two power connectors. See Figure 13 on page 34 for the
location of the power connectors.
Fan Headers
The Desktop Board has a 3-pin MCH fan header and a 3-pin chassis fan header. See
Figure 12 on page 33 for the location of the chassis fan header.
+5 V Standby Power Indicator LED
CAUTION
If the AC power has been switched off and the standby power indicator is still lit,
disconnect the power cord before installing or removing any devices connected to the
board. Failure to do so could damage the board and any attached devices.
The Desktop Board’s standby power indicator, shown in Figure 4, is lit when there is
standby power to the system. This includes the DIMM socket and the PCI bus
connector, even though the computer appears to be off.
Desktop Board Features
19
Figure 4. Location of the Standby Power Indicator
For more information on standby current requirements for the Desktop Board, refer to
the Technical Product Specification on the Intel Desktop D945GCLF2 web page at
http://support.intel.com/support/motherboards/desktop/
LAN Wake Capabilities
CAUTION
For LAN wake capabilities, the 5 V standby line for the power supply must be capable
of delivering adequate +5 V standby current. Failure to provide adequate standby
current when using this feature can damage the power supply.
LAN wakeup capabilities enable remote wake-up of the computer through a network.
The LAN subsystem monitors network traffic and upon detecting a Magic Packet*
frame, it asserts a wake-up signal that powers up the computer.
Wake from USB
NOTE
Wake from USB requires the use of a USB peripheral that supports wake from USB.
USB bus activity wakes the computer from an ACPI S3 state.
Intel Desktop Board D945GCLF2 Product Guide
20
Wake from PS/2 Keyboard/Mouse
PS/2 keyboard/mouse activity wakes the computer from the ACPI S1, S3, S4, and S5
states.
PME# Wakeup Support
When the PME# signal on the PCI bus is asserted, the computer wakes from the ACPI
S1, S3, S4, and S5 states.
Battery
A battery on the Desktop Board keeps the values in CMOS RAM and the clock current
when the computer is turned off. Go to page 37 for instructions on how to replace the
battery.
Real-Time Clock
The Desktop Board has a time-of-day clock and 100-year calendar. The battery on the
Desktop Board keeps the clock current when the computer is turned off.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58

Intel BLKD945GCLF2 Manuale utente

Categoria
Schede madri
Tipo
Manuale utente

in altre lingue