Apex Digital Domus 2 Istruzioni per l'uso

Marca: Apex Digital

Modello: Domus 2

Tipo: Istruzioni per l'uso

1 2 3 4 476006-0000 V1.0

Alternating Pressure Redistribution System

Operation Manual

IMPORTANT SAFEGUARDS

READ ALL INSTRUCTIONS BEFORE USING

DANGER - To reduce the risk of electrocution:

1. Always unplug this product immediately after using.

2. Do not use while bathing.

3. Do not place or store this product where it can fall or be pulled into a tub or sink.

4. Do not place in or drop into water or other liquid.

5. Do not reach for a product that has fallen into water. Unplug immediately.

WARNING - To reduce the risk of burns, electrocution, fire or injury to persons:

1. Evaluate patients for entrapment risk according to protocol and monitor patients appropriately.

2. This system is not for use with patients who have a spinal cord injury.

3. Close supervision is necessary when this product is used on or near children. Electrical

burns or choking accident may result from a child swallowing a small part detached from the

device.

4. Use this product only for its intended use as described in this manual. Do not use other

mattress not recommended by the manufacturer.

5. Never operate this product if it has a damaged cord or plug, if it is not working properly, if it

has been dropped or damaged, or dropped into water. Return the product to your supplier or

Apex Medical Corp. for examination and repair.

6. Keep the cord away from heated surfaces.

7. Never block any air openings of this product or place it on soft surfaces, such as a bed or

couch, where openings may be blocked. Keep the air opening free of lint, hair, and other

similar particles.

8. Never drop or insert any object into any opening or hose.

9. Do not modify this equipment without authorization of the manufacturer.

10. Mattress covers have passed skin sensitization and skin irritation test. However, if you

suspect that you may have had or are having an allergic reaction, please consult a physician

immediately.

11. Do not leave long lengths of tubing around the top of your bed. It could lead to strangulation.

CAUTION –

If there is a possibility of electro-magnetic interference with mobile phones, please increase the

distance (3.3m) between devices or turn off the mobile phone.

NOTE, CAUTION AND WARNING STATEMENTS:

NOTE - Indicate some tips.

CAUTION - Indicate correct operating or maintenance procedures in order to prevent

damage to or destruction of the equipment or other property

WARNING - Calls attention to a potential danger that requires correct procedures or

practices in order to prevent personal injury.

1. INTRODUCTION

This manual should be used for initial set up of the system and for reference purposes.

1.1 General Information

The system is a high quality and affordable mattress system suitable for treatment

and prevention of pressure ulcers.

The system has been tested and successfully approved to the following standards:

EMC Warning Statement

This equipment has been tested and found to comply with the limits for medical devices to the EN

60601-1-2:2007. These limits are designed to provide reasonable protection against harmful

interference in a typical medical installation. This equipment generates uses and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions, may cause

harmful interference to other devices in the vicinity. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful

interference to other devices, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the following measures:

 Reorient or relocate the receiving device.

 Increase the separation between the equipment.

 Connect the equipment into an outlet on a circuit different from that to which the other

device(s) are connected.

 Consult the manufacturer or field service technician for help.

1.2 Intended Use

This product is intended:

 to help and reduce the incidence of pressure ulcers while optimizing patient comfort.

 for long term home care of patients suffering from pressure ulcers.

 for pain management as prescribed by a physician.

The product can only be operated by personnel who are qualified to perform general nursing

procedures and have received adequate training in knowledge of prevention and treatment of

pressure ulcers.

NOTE: This equipment is not suitable for use in the presence of flammable anesthetic

mixture with air or with pure oxygen or nitrous oxide.

1.3 Warranty-

The Company warrants the pump at the time of its original purchase and for the subsequence time

of period of one year.

The company warrants the bubble pad at the time of its original purchase and for the subsequence

time of period of six months.

The warranty does not cover the followings:

1. The series number label of pump or pads is turn off or cannot be recognized.

2. Damage to the pump or bubble pad resulting from misconnections with other devices.

3. Damage to the device resulting from accidents.

SYMBOL DEFINITION

2. PRODUCT DESCRIPTION

2.1 Pump Unit

2.2 Front panel

1. Pressure Adjust Knob

Pressure adjust knob controls the air pressure output. Please

consult the physician for a suitable setting.

2. Main Power Switch

To turn the pump unit on/off.

3. INSTALLATION

Unpack the box and check the package contents for completeness. If there are any damages,

please immediately contact your supplier or Apex Medical Corp

3.1 Pump & Mattress Installation

1. Place the DOMUS 2 on top of a foam or mattress bed. Secure the

mattress firmly by fixing the straps to the bed frame if available.

NOTE: DOMUS 2 is an overlay system, so there must be a foam or

mattress underneath when using.

2. Hang the pump onto the footboard and adjust hangers so the pump is

secured in an upright position; or place the pump on a flat surface.

3. Connect air hose connectors from air mattress to the pump unit.

NOTE: Check and ensure the air hoses are not kinked or tucked

under mattress.

4. Plug the power cord into electrical outlet.

NOTE: 1. Make sure the pump unit is suitable for the local power

voltage. 2. The plug is also served to disconnect the device. Do not

position the equipment so that it is difficult to disconnect the device.

CAUTION: The pump should only be used with mattress recommended by the manufacturer. Do

not use it for any other purpose.

5. Turn the main power switch found from the right side of the pump to ON position.

Several installation tips are listed below:

After installation, the extra length of the power cord, if any, should be neatly arranged to avoid any

tripping accidents. The EQUIPMENT should be firmly placed at position where users/doctors can

access easily.

4. OPERATION

NOTE: Always read the operating instruction before use.

4.1 General operation

1. Switch on the main power switch on right side of the pump.

2. Adjust the pressure setting based upon patient comfort level by turning the pressure

adjustment knob clockwise to increase firmness.

NOTE: Every time the mattress is set up for use, it is recommended that the pressure first

to be set to the max. The user / career can then adjust air mattress weight levels to the

desired softness after set up has been completed

4.2 Emergency operation

When there is a need to perform emergency CPR on the patient, pull the quick release CPR

tag located at the head-end of the mattress on the right hand side if available. The quick

connector found from the pump unit can also be disconnected to hasten deflation. Be sure to

reconnect the quick connector to the pump unit once restore the power supply.

5. CLEANING

It is important to follow the cleaning procedures before using the equipment on human bodies;

otherwise, patients and/or doctors may have the possibility of getting infection.

CAUTION- Do not immerse or soak pump unit.

Wipe the pump unit with a damp cloth and a mild detergent. If other detergent is used, choose one

that will have no chemical effects on the surface of the plastic case of the pump unit.

Wipe down the mattress with warm water containing a mild detergent. The cover may also be

cleaned by using sodium hypochlorite diluted in water. All parts should be air dried thoroughly

before use.

CAUTION - Do not use phenolic based product for cleaning.

CAUTION - After cleaning, dry the mattress without direct exposure sunlight.

6. STORAGE

1. Lay the bubble pad or mattress on a flat surface and upside down.

2. Roll-up the mattress from the head end towards the foot end.

3. Foot-end strap can then be stretched around the rolled pad/ mattress to prevent

unrolling.

NOTE : Do not fold, crease or stack the mattresses.

7. MAINTENANCE

1. Check main power cord and do not plug it if there is an abrasion or excessive wear.

2. Check mattress cover for signs of wear or damage. Ensure mattress cover and tubes

are stubbed together correctly.

3. Check the airflow from the air hose. The airflow should alternate between each

connector every half-cycle time.

4. Check the air hoses if there is kink or breaks. For replacement, please contact Apex

Medical Corp. or your suppliers.

8. EXPECTED SERVICE LIFE

The products are intended to offer safe and reliable operation when used or installed according to

the instructions provided by Apex Medical. Apex Medical recommends that the system be

inspected and serviced by authorized technicians if there are any signs of wear or concerns with

device function. Otherwise, service and inspection of the devices generally should not be required.

9. TROUBLESHOOTING

NOTE : If the pressure level is consistently low, check for any leakage (tubes or air hoses). If

necessary, replace any damaged tubes or hoses or contact your local qualified dealer

for repair.

10. TECHNICAL SPECIFICATION

Item Specification

Model Domus 2 (9P-047580)

Power Supply (Note: See rating

label on the product)

AC230V 50Hz, 0.05A

Fuse Rating T1AL, 250V

Dimension (L x W x H) 25 x 12.5 x 8.5 cm / 9.8" x 4.9” x 3.3 “

Cycle Time 9.6 mins.

Weight 1.4 Kg / 3.08 lb

Atmospheric

Pressure

700 hPa to 1013.25 hPa

Temp.

Operation: 10°C to 40°C (50°F to 104°F)

Storage: -15°C to 50°C (5°F to 122°F)

Shipping: -15°C to 70°C (5°F to 158°F)

Environment

Humidity

Operation: 10% to 90% non-condensing

Storage: 10% to 90% non-condensing

Shipping: 10 % to 90% non-condensing

Classification Class II, Type BF, IP21

Mattress Specification

Model 4” Mattress

Dimension (L x W x H)

190x80x10.2(cm)/

74.8”x31.5” x 4”

Weight 4.3 kg/9.48 lb

Pressure Range (mmHg) 30- 80

NOTE: Please follow national requirements to dispose the unit properly.

Appendix A: EMC Information

Guidance and Manufacturer’s Declaration- Electromagnetic Emissions:

This device is intended for use in the electromagnetic environment specified below. The user of this device should

make sure it is used in such an environment.

Emissions Test Compliance Electromagnetic Environment-Guidance

RF emissions

CISPR 11

Group 1

RF emissions

CISPR 11

Class B

The device uses RF energy only for its internal function.

Therefore, its RF emissions are very low and are not likely to

cause any interference in nearby electronic equipment

Harmonic emissions

IEC61000-3-2

Class A

Voltage fluctuations / Flicker

emissions

IEC61000-3-3

Complies

The device is suitable for use in all establishments, including

domestic establishments and those directly connected to the

public low-voltage power supply network.

Guidance and Manufacturer’s Declaration- Electromagnetic Immunity:

This device is intended for use in the electromagnetic environment specified below. The user of this device should

make sure it is used in such an environment.

Immunity Test IEC60601 test level Compliance

Electromagnetic

Environment-Guidance

Electrostatic

Discharge (ESD)

IEC61000-4-2

±6kV contact

±8kV air

±6kV contact

±8kV air

Floors should be wood, concrete or

ceramic tile. If floors are covered with

synthetic material, the relative

humidity should be at least 30 %.

Electrical fast

transient/ burst

IEC61000-4-4

±2kV for power supply line

±1kV for input/out line

±2kV for power supply

line

±1kV for input/out line

Mains power quality should be that of

atypical commercial or hospital

environment

Surge

IEC61000-4-5

± 1 kV line(s) to

line(s)

± 2 kV line(s) to earth

± 1 kV line(s) to

line(s)

Mains power quality should be that of

atypical commercial or hospital

environment.

Voltage dips, short

interruptions and

voltage variations on

power supply input

lines

IEC61000-4-11

<5 % U

(>95 % dip in

)for 0,5 cycle

40 % U

(60 % dip in U

)for

5 cycles

70 % U

(30 % dip in U

)for

25 cycles

<5 % U

(>95 % dip in

)for 5 sec

<5 % U

(>95 % dip in U

)

for 0,5 cycle

40 % U

(60 % dip in U

)

for 5 cycles

70 % U

(30 % dip in U

)

for 25 cycles

<5 % U

(>95 % dip in U

)

for 5 sec

Mains power quality should be that of

atypical commercial or hospital

environment. If the user of this device

requires continued operation during

power mains interruptions, it is

recommended that the device be

powered from an uninterruptible power

supply or a battery.

Power frequency

(50/60Hz)

magnetic field

IEC61000-4-8

3 A/m 3 A/m

Power frequency magnetic fields

should be at levels characteristic of

atypical location in a typical

commercial or hospital environment.

NOTE: U

is the A.C. mains voltage prior to the application of the test level

Guidance and Manufacturer’s Declaration - Electromagnetic Immunity:

This device is intended for use in the electromagnetic environment specified below. The user of this device should

make sure it is used in such an environment.

Immunity Test IEC60601 test level

Compliance Electromagnetic Environment-Guidance

Conducted RF

IEC 61000-4-6

Radiated RF

IEC 61000-4-3

3 Vrms 150 kHz to

80 MHz outside ISM

bands

3 V/m 80 MHz to 2.5

GHz

3 Vrms

3 V/m

Portable and mobile RF communications equipment should

be used no closer to any part of this device, including

cables, than there commended separation distance

calculated from the equation applicable to the frequency of

the transmitter.

Recommended separation distance

Pd 2.1=

150kHz to 80MHz

Pd 2.1=

150kHz to 80MHz

Pd 3.2=

80 MHz to 2.5G MHz

Where P is the maximum output power rating of the

transmitter in watts (W) according to the transmitter

manufacturer and d is the recommended separation

distance in meters (m).

Field strengths from fixed RF transmitters, as determined by

an electromagnetic site survey

, should be less than the

compliance level in each frequency range

Interference may occur in the vicinity of equipment marked

with the following symbol:

NOTE 1: At 80 MHz and 800 MHz, the higher frequency range applies.

NOTE 2: These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and

reflection from structures, objects and people.

The ISM (industrial, scientific and medical) bands between 150 kHz and 80 MHz are 6,765 MHz to 6,795 MHz;13,553

MHz to 13,567 MHz; 26,957 MHz to 27,283 MHz; and 40,66 MHz to 40,70 MHz.

The compliance levels in the ISM frequency bands between 150 kHz and 80 MHz and in the frequency range 80 MHz

to 2.5 GHz are intended to decrease the likelihood that mobile/portable communications equipment could cause

interference if it is inadvertently brought into patient areas. For this reason, an additional factor of 10/3 is used in

calculating the recommended separation distance for transmitters in these frequency ranges.

Field strengths from fixed transmitters, such as base stations for radio (cellular/cordless) telephones and land /

mobile

radios, amateur radio, AM and FM radio broadcast and TV broadcast cannot be predicted theoretically with accuracy.

To assess the electromagnetic environment due to fixed RF transmitters, an electromagnetic site survey should be

considered. If the measured field strength in the location in which the device is used exceeds the applicable RF

compliance level above, the device should be observed to verify normal operation. If abnormal performance is

observed, additional measures may be necessary, such as reorienting or relocating the device.

Over the frequency range 150 kHz to 80 MHz, field strengths should be less than 3 V/m.

Recommended separation distances between portable and mobile RF communications equipment and this

device:

This device is intended for use in an electromagnetic environment in which radiated RF disturbances are controlled.

The customer or the user of this device can help prevent electromagnetic interference by maintaining a minimum

distance between portable and mobile RF communications equipment (transmitters) and this device as recommended

below, according to the maximum output power of the communications equipment

Separation distance according to frequency of transmitter m

Rated maximum output

power of transmitter

150 kHz to 80 MHz

Pd 2.1=

80 MHz to 800 MHz

Pd 2.1=

800 MHz to 2,5 GHz

Pd 3.2=

0.01 0.12 0.12 0.23

0.1 0.38 0.38 0.73

1 1.2 1.2 2.3

10 3.8 3.8 7.3

100 12 12 23

For transmitters

rated at a maximum output power not listed above, the recommended separation distance d in meters

(m) can be estimated using the equation applicable to the frequency of the transmitter, where P is the maximum output

power rating of the transmitter in watts (W) according to the transmitter manufacturer.

Note 1: At 80 MHz and 800 MHz, the separation distance for the higher frequency range applies.

Note 2: These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption a

reflection from structures, objects, and people.

APEX MEDICAL S.L. APEX MEDICAL CORP. Manufacturing Facility:

Elcano 9, 6

planta No.9, Min Sheng St., Tu-Cheng, Apex Medical (Kunshan) Corp.

48008 Bilbao. Vizcaya. Spain New Taipei City, 23679, Taiwan No. 1368, Zi Zhu Rd. Kunshan

www.apexbrand.com

JiangSu Sheng, China

Manufacturer.

Dry clean, Any Solvent

Except Trichloroethylene

Authorized representative in the European

community.

Do Not Iron

Attention, should read the instructions.

Tumble Dry, Normal, Low

Heat

Catalogue Number

Do Not Tumble Dry

Class II Equipment.

Do Not Bleach

"BF" symbol, indicate this product is according

to the degree of protecting against electric

shock for type BF equipment.

Do Not Dry Clean

Protected against solid foreign objects of 12.5

mm and greater. Protection against vertically

falling water drops

Machine wash, regular /

normal, 60 degrees C

(140degrees F)

Refer to instruction manual/ booklet/NOTE on

ME EQUIPMENT "Follow instructions for use

Temperature Limitation

Waste Electrical & Electronic Equipment (WEEE): This product should be handed over to

an applicable collection point for the recycling of electrical and electronic equipment. For

more detailed information about the recycling of this product, please contact your local city

office, household waste disposal service or the retail store where you purchased this

product.

Problem Solution

Power is not ON ‧

‧‧

‧

Check if the plug is connected to mains.

Patient is bottoming out

‧

‧‧

‧

Pressure setting might be inadequate for the patient, adjust comfort range 1 to 2

levels higher and wait for a few minutes for best comfort.

Mattress form is loose

‧

‧‧

‧

Check if all the snap buttons or straps of mattress are all securely fastened.

‧

‧‧

‧

Check if the mattress is fixed to the bed frame by straps.

No air produced from some

air outlets of the air tube

connector

‧

‧‧

‧

This is normal since there is alternating mode. Air outlets take turns to produce air

during their cycle time.

EN 60601

EN 60601-1-2

EN 55011 Class B

EN 61000-3-2 Class A

EN 61000-3-3

Front

1. Power Switch

2. Front Panel

Rear

3. Air Hose Port

4. Hanger

5. Power Cord

5 6 7 8 476006-0000 V1.0

1. INTRODUCCIÓN

Este manual debe ser utilizado para una instalación inicial y como

referencia posterior.

2. DESCRIPCIÓN DEL PRODUCTO

2.1 COMPRESOR

Frontal

1. Interruptor

2. Panel frontal

Parte trasera

3. Salida de aire

4. Colgadores

5. Cable eléctrico

2.2 Panel frontal

1. Regulador de presión

Controla la salida de presión de aire. Si

gira en sentido de las manillas del reloj,

la presión incrementará. Por otro lado, si

gira en sentido contrario a las manillas

del reloj, la presión reducirá.

2. Interruptor principal

Para encender/ apagar el compresor.

3. INSTALACIÓN

Desembale el equipo para comprobar cualquier daño que haya

podido ocurrir durante el envío. En caso de daños, contacte

inmediatamente con el punto de venta donde adquirió el equipo.

1. Coloque el DOMUS 2 en la parte superior de una espuma o

colchón de la cama. Sujete el colchón

a la cama mediante las tiras de nylon

si las tuviera

NOTA: DOMUS 2 es un superposiciones,

por lo que debe ser una espuma o debajo del

colchón cuando se utiliza.

2. Colgar el compresor de la barandilla o del piecero de la cama y

ajustar los colgadores para que quede fijado en posición

vertical, o posicionarlo en una superficie plana.

3. Conecte la salida/entrada de aire del colchón al compresor.

NOTA: Asegúrese de que los tubos

de aire no han quedado escondidos o

doblados bajo el colchón

Conecte el cable eléctrico a la corriente

NOTA: 1. Asegúrese que el

compresor es apropiado para el voltaje

eléctrico local. 2. El enchufe también puede

servir como para desconectar el aparato

PRECAUCIÓN: La bomba solamente se puede aplicar al

colchón recomendado por el fabricante. No la utilice pata ninguna

otra finalidad. (Parte aplicada: colchón de aire).

4. Encienda el interruptor que está situado al lado derecho del

compresor.

Varios Consejos de instalación:

Después de la instalación, los restos de cable que puedan quedar al aire

deberán de ser correctamente recogidos con el fin de evitar un posible

tropiezo. El equipo debe estar situado en un lugar con total accesibilidad

para los usuarios o médicos.

4. FUNCIONAMIENTO

NOTA: Lea las instrucciones de funcionamiento antes de su uso.

4.1 FUNCIONAMIENTO GENERAL

1. Encienda el interruptor principal que se encuentra en un lateral

del compresor.

2. El compresor empieza a expulsar aire hacia el colchón. Gire el

regulador en sentido de las agujas del reloj para aumentar la

presión (Firmeza) en el colchón.

NOTA: Cada vez que se quiera inflar el colchón es recomendable

mantener el regulador de presión al máximo para un

llenado más rápido. Una vez hinchado el colchón, el

usuario podrá regular la firmeza o presión

4.2 CPR

En caso de emergencia y de que exista parada respiratoria, extraer

inmediatamente la válvula CPR del colchón. Las válvulas CPR están

situadas en la parte superior derecha del colchón. Para un vaciado

más rápido, también se pueden desconectar los tubos de aire

conectados al compresor, pero solamente aquellos modelos que

están equipados con “Quick connectors”.

5. LIMPIEZA

Es importante seguir el procedimiento de limpieza antes de usar el

equipo en cuerpos humanos, de lo contrario los pacientes y/o

médicos pueden tener la posibilidad de contraer infecciones.

Pase un trapo húmedo con detergente suave por el compresor y

manténgalo alejado del polvo. Si utiliza otro detergente, elija uno que

no provoque efectos químicos en la superficie de la carcasa de

plástico del compresor.

ADVERTENCIA: No sumerja en líquido ni moje el compresor.

Pase un trapo húmedo con agua templada (no exceda de 65ºC) y

detergente suave por el colchón. La cubierta también puede ser lavada

con Hipoclorito sódico diluido en agua. Todas las partes deben ser

secadas al aire minuciosamente antes de su uso.

ADVERTENCIA :No utilizar productos basados en alcohol /

componentes fenólicos.

ADVERTENCIA :Dejar que el colchón se seque al aire después de

su limpieza. Pero no exponerlo prolongadamente al sol directo.

6. ALMACENAJE

Para colchones de celdas:

1. Para almacenar el colchón, extiéndalo a lo largo y boca abajo.

2. Enrollar desde el cabezal hacia el otro extremo del colchón.

3. Una vez enrollado, envolver el colchón con la cinta que se

encuentra en la parte final para evitar que se desenrolle.

4. Doble el colchón como el método original.

7. MANTENIMIENTO

1. Asegúrese de que el cable y enchufe se encuentren en buen

estado.

2. Compruebe el estado de la cubierta. Asegúrese que la cubierta

junto con los tubos están almacenados correctamente.

3. Compruebe el flujo de aire de los tubos. El flujo de aire debe

alternar entre los dos conectores en caso de que esté en modo

función alternante.

4. Asegúrese que las salidas de aire no está rotas o dañadas.

Para su sustitución contactar con el punto de venta donde

adquirió el sistema.

1. INTRODUÇÃO

Este manual deve ser utilizado para a montagem inicial e para futuras

referências.

2. DESCRIÇÃO DO PRODUTO

2.1 COMPRESOR

Frente

1. Interruptor

2. Painel frontal

Trás

3. Abraçadeiras de montagem

4. Entrada da mangueira do ar

5. Cabo de alimentação eléctrica

2.2 PAINEL FRONTAL

1. Manípulo de ajuste de pressão

O Manípulo de ajuste de pressão controla

apressão do ar que sai. Quando rodada

nosentido dos ponteiros do relógio, a saída

de ar aumenta. Por outro lado, quando

rodada no sentido inverso a pressão

diminuirá. Por favor contacte o seu

fisioterapeuta para optar por uma pressão

adequada.

2. Interruptor Eléctrico Principal

Para ligar/desligar a unidade da bomba

3. INSTALAÇÃO

Abra a caixa para verificar se ocorreu algum dano durante o transporte.

Se sim, por favor contacte o nosso revendedor imediatamente.

1. Coloque a DOMUS 2 no topo de uma

espuma ou de colchão da cama. Proteja o

colchão firme, fixando as correias para a

estrutura da cama, se disponível.

ATENÇÃO- DOMUS 2 é uma sobreposição,

portanto, deve haver uma espuma ou por baixo

do colchão quando se usa.

2. Pendure a bomba na armação da cama

(junto à parte dos pés) e ajuste as

abraçadeiras de montagem ou coloque a

bomba numa superfície plana.

3. Conecte a mangueira do ar do colchão à

unidade da bomba.

ATENÇÃO- Verifique e certifique-se se

as mangueiras não estã dobradas ou presas

debaixo do colchão.

4. Ligue o cabo de alimentação a uma

tomada.

5. Depois coloque o Interruptor Eléctrico rincipal na posição ON

(ligado).

ATENÇÃO- 1.Certifique-se que a unidade da bomba é

adequada para a voltagem da rede local. 2.A ficha pode também ser

usada para desligar o dispositivo.

CUIDADO- A bomba apenas pode ser usada juntamente com o

colchão recomendado pelo fabricante. Não a use para qualquer

outro fim. (Item ao qual se aplica: colchão de ar)

Em baixo, apresentam-se algumas dicas de instalação:

Depois da instalação, o que sobra do cabo de alimentação eléctrica, se

sobrar, deve ser cuidadosamente arrumado para evitar acidentes. O

EQUIPAMENTO deve ser colocado firmemente num ponto de fácil acesso

para utilizadores / médicos.

4. UTILIZAÇÃO

ATENÇÃO

:Leia sempre as instruções de uso antes da utilização.

4.1 Utilização Geral

1. Ligue o interruptor eléctrico principal.

2. A unidade da bomba começa a fornecer ar ao colchão

ATENÇÃO

:Sempre que o colchão for insuflado pela primeira vez,

recomendamos que o manípulo de controlo de pressão seja ajustado

para “Firme” para que se verifique em enchimento mais rápido. Depois de

cheio o utilizador poderá ajustar o colchão de ar para a rigidez desejada.

4.2 NIDADE DE REANIMAÇÃO

Quando ocorrer uma emergência que exija a utilização da UNIDADE DE

REANIMAÇÃO no paciente, puxe rapidamente as válvulas da UNIDADE

DE REANIMAÇÃO para libertar ar do colchão. As válvulas da UNIDADE

DE REANIMAÇÃO estão localizadas na parte da cabeça do colchão, do

lado direito. A mangueira do ar da unidade da bomba pode ainda ser

retirada para permitir um esvaziamento mais rápido

5. LIMPEZA

É importante respeitar os procedimentos de limpeza antes de utilizar a

máquina em humanos. Caso contrário, existe o risco dos pacientes e/ou

médicos apanharem infecções.

Limpe a unidade da bomba com um pano húmido e detergente suave e

mantenha-a livre de pó. Se utilizar outro tipo de detergente, certifique-se

que este não vai ter nenhum efeito químico na caixa plástica da unidade

da bomba.

CUIDADO: Não emergir ou ensopar a unidade da bomba.

Limpe o colchão utilizando água morna com detergente suave. A

cobertura também pode ser limpa usando hipo cloreto de sódio diluído em

água. Todas as partes devem secar completamente ao ar antes de

utilizar.

CUIDADO: Não utilizar produtos corrosivos na limpeza.

CUIDADO: Secar o colchão em áreas sem sol directo depois da

limpeza.

6. ARMAZENAGEM

1. Para arrumar, deite o colchão esticado e de pernas para o ar.

2. Enrole da parte da cabeça em direcção à parte dos pés.

3. A fivela que existe na parte dos pés poderá então ser fixada em

torno do colchão enrolado para que este não se desenrole.

4. No caso do colchão de ar, enrole tal como descrito.

7. MANUTENÇÃO

1. Verifique se o cabo e a ficha eléctrica não sofrem de desgaste

ou utilização excessiva.

2. Verifique a existência de sinais de desgaste ou danos na

cobertura do colchão. Certifique-se que a cobertura do colchão

e as tubagens estão correctamente encaixados juntos.

3. Verifique a circulação de ar na mangueira do ar. O fluxo de ar

deve alternar entre cada conector a cada meio ciclo de tempo.

4. Verifique se existem quebras ou dobras nas mangueiras do ar.

Para as substituir, por favor contacte os nossos revendedores

locais.

Portu

ês

Espa

9 10 11 12 476006-0000 V1.0

1. INTRODUCTION

Ce manuel doit être utilisé pour une installation initiale et comme

référence postérieure.

2. DESCRIPTION DU PRODUIT

2.1 COMPRESSEUR

PARTIE AVANT

1. INTERRUPTEUR

2. PANNEAU FRONTAL

2.2 PARTIE ARRIÈRE

3. SALIDA DE AIRE

4. CROCHETS

5. CABLE ELECTRIQUE

2.2 panneau AVANT

1. Régulateur de pression

Il contrôle la sortie de pression de l'air.

Si vous le tournez dans le sens des

aiguilles d'une montre, la pression

augmentera. Si vous le tournez dans

l'autre sens, la pression diminuera. La

gamme de confort 1-8 offre différents

soutiens de poids, principalement en

fonction du type de matelas.

2. Interruptor principal

Pour allumer/éteindre le compresseur.

3. INSTALLATION

Déballez l'appareil afin de vérifier tout dommage éventuellement

occasionné pendant l'envoi. En cas de dommages, contactez

immédiatement le point de vente qui vous a vendu l'appareil.

1. Placez cer le DOMUS 2 au sommet d'une

mousse ou matelas. Fixez le matelas au lit à

l'aide des sangles en nylon, le cas échéant.

NOTE - DOMUS 2 est un surmatelas, il doit y

avoir une mousse ou un matelas en dessous lors de

l'utilisation.

2. Accrochez le compresseur à la tête ou au pied

du lit, ou positionnez-le sur une surface plane

3. Branchez la sortie/entrée d'air du matelas au

compresseur.

NOTE - Vérifiez que les tuyaux d'air ne sont

pas cachés ou pliés sous le matelas.

4. Branchez le câble d'alimentation au courant Electrique.

NOTE - 1. Vérifiez que le compresseur peut bien être utilisé sur la

tension électrique locale. 2.La prise peut aussi également servir

d'interrupteur.

5. Allumez l’interrupteur situé sur le côté droit du compresseur.

ATTENTION - Le compresseur peut uniquement être utilisé avec le

matelas d'air recommandé par le fabricant. Ne pas l'utilisez à d'autres fins

Plusieurs conseils d'installation:

Après installation, les autres câbles à l'air libre doivent être correctement

repliés afin d'éviter tout risque de chute. L'appareil doit être situé dans un

endroit facilement accessible pour les utilisateurs ou médecins.

4. FONCTIONNEMENT

NOTE : lisez attentivement les instructions de fonctionnement

avant d'utiliser l'appareil.

4.1 FONCTIONNEMENT GÉNÉRAL

1. Allumez l'interrupteur principal se trouvant à droite du

compresseur.

2. Le compresseur commence à expulser de l'air vers le matelas.

Tournez le régulateur dans le sens des aiguilles d'une montre

afin d'augmenter la pression (fermeté) du matelas

NOTE: Chaque fois que vous souhaitez gonfler le matelas, il est

recommandé de positionner le régulateur de pression au maximum pour

un gonflage plus rapide. Une fois le matelas gonflé, l'utilisateur pourra

régler sa fermeté ou sa pression.

4.2 CPR

En cas d'urgence et d'arrêt respiratoire, retirez immédiatement la valve

CPR du matelas. Les valves CPR sont situées sur la partie supérieure

gauche du matelas (uniquement disponibles sur les matelas à cellules

d'air supérieures à 6,35cm). Pour un dégonflage plus rapide, vous pouvez

débrancher les tubes d'air reliés au compresseur, mais uniquement sur

les modèles équipés de « quick connectors ».

5. NETTOYAGE

Il est important d'appliquer la procédure de nettoyage avant d'utiliser

l'appareil sur les corps humain. Dans le cas contraire, les patients

et/ou médecins pourraient contracter des infections.

Passez un chiffon humide avec un détergent doux sur le compresseur et

tenez-le à l'écart de la poussière. Si vous utilisez un autre détergent,

choisissez-en un sans effets chimiques sur la surface de la carcasse en

plastique du compresseur.

AVERTISSEMENT : Ne pas plonger le compresseur dans un

liquide ni le mouiller.

Passez un chiffon humide imprégné d’eau tiède et de détergent doux sur

le matelas. La couverture peut également être lavée avec de

l’hypochlorite de sodium dilué dans de l’eau. Tous les éléments doivent

être soigneusement séchés à l’air libre avant d’utiliser l’appareil.

AVERTISSEMENT : Ne pas utiliser de produits à base d'alcool /

composants phénoliques.

AVERTISSEMENT : Laissez le matelas sécher à l'air libre après

nettoyage mais ne l'exposez pas directement au soleil pendant une trop

longue durée.

6. RANGEMENT

1. Pour les matelas de cellules :

2. Pour ranger le matelas, étendez-le en long et la tête en bas.

3. Enroulez-le de la tête vers l’autre extrémité du matelas avec la

valve CPR ouverte.

4. Une fois roulé, enveloppez le matelas à l’aide du ruban fixé au

bout, afin d’empêcher qu’il ne se déroule.

5. En cas de « bubble pad », pliez le matelas tel que vous l’avez

reçu.

7. ENTRETIEN

1. Vérifiez que le câble et la prise se trouvent en bon état.

2. Vérifiez l'état du couvercle. Vérifiez que le couvercle et les

tuyaux sont bien correctement rangés.

3. Vérifiez le débit d'air des tuyaux. Le débit d'air doit passer d'un

connecteur à l'autre si celui-ci est en mode de fonctionnement

alterné.

Vérifiez que les sorties d’air ne sont ni cassées ni endommagées. Pour

procéder à leur remplacement, contactez le point de vente où vous avez

acheté l’appareil.

1. EINFÜHRUNG

Dieses Handbuch sollte bei der Erstinstallation und als spätere Referenz

verwendet werden.

2. BESCHREIBUNG Des Produkts

2.1 KOMPRESSOR

VORDERSEITE:

1. Schalter

2. Frontplatte

RÜCKSEITE:

3. Luftauslass

4. Bügel

5. Stromkabel

2.2 Schutzabdeckung

1. Druckregler.

Er regelt den Druckluftauslass. Wenn Sie ihn

im Uhrzeigersinn drehen, erhöht sich der

Druck. Wenn Sie ihn entgegen dem

Uhrzeigersinn drehen, verringert sich der

Druck. Bitte fragen Sie Ihren Arzt nach der

geeigneten Einstellung

2. Hauptschalter

Zum Ein-/ Ausschalten des Kompressors. Es

leuchtet eine grüne Lampe auf

3. INSTALLATIÓN

Packen Sie das Produkt aus und prüfen Sie die Komponenten auf

mögliche Schäden, die während des Transports entstanden sein könnten.

Sollten Sie jegliche Schäden bemerken, wenden Sie sich bitte umgehend

an Ihren Händler

1. Legen Sie die Matratze auf das Bett. Bitte

achten Sie auf das Fußende des Bettes

WICHTIG:

DOMUS 2 ist ein

Matratzenauflagesysteme, so muss es einen

Schaum oder eine Matratze unter bei der

Verwendung.

2. Hängen Sie den Kompressor am Geländer

oder am Fußteil des Bettes ein, oder legen

Sie ihn auf eine ebene Fläche

3. Verbinden Sie den Luftaus-/einlass der

Matratze mit dem Kompressor.

WICHTIG : Versichern Sie sich, dass die

Luftschläuche nicht unter der Matratze verborgen

oder geknickt sind.

4. Verbinden Sie das Stromkabel mit dem Stromanschluss

WICHTIG : 1. Versichern Sie sich, dass der Kompressor für die

Stromspannung vor Ort geeignet ist.

2. Der Stecker kann ebenfalls zum Ausschalten dienen

ACHTUNG : Der Kompressor darf nur mit der vom Hersteller

empfohlenen Matratze verwendet werden. Verwenden Sie ihn zu keinem

anderen Zweck

5. Schalten Sie den Schalter ein, der rechts vom Kompressor liegt.

Verschiedene Tipps zur Installation:

Nach der Installation müssen die restlichen Teile des Kabels, die noch

offen liegen könnten, ordentlich aufgewickelt werden, um zu vermeiden,

dass man darüber stolpert. Das Gerät muss stabil und an einem für den

Nutzer oder den Arzt leicht zugänglichen Ort aufgestellt werden.

4. FUNKTIONSWEISE

WICHTIG - Lesen Sie die Hinweise zur Funktionsweise vor dem

Gebrauch durch.

4.1 Allgemeine Funktionsweise

1. Schalten Sie den Hauptschalter ein.

2. Der Kompressor beginnt Luft in die Matratze zu pumpen

WICHTIG: Immer wenn Sie die Matratze aufpumpen möchten, ist

es empfehlenswert, den Druckregler auf den Höchststand einzustellen,

um ein schnelleres Aufpumpen zu erreichen. Sobald die Matratze

aufgepumpt ist, kann der Benutzer die Festigkeit oder den Druck

derselben regeln.

4.2 CPR

Im Notfall, und falls ein Atemstillstand eintritt, öffnen Sie unverzüglich das

CPR-Ventil der Matratze. Die CPR-Ventile befinden sich an der linken

unteren Seite der Matratze. (Nur verfügbar bei Matratzen mit Luftzellen

über 6,35 cm). Für eine schnellere Entleerung können auch am

Kompressor angeschlossenen Luftschläuche abgetrennt werden, doch

nur bei Modellen, die mit “quick connectors” (Steckverbindungen)

ausgestattet sind.

5. REINIGUNG

Es ist wichtig, die Reinigungsprozedur zu befolgen, bevor das Gerät am

menschlichen Körper angewandt wird, da der Patient und/oder der Ärzt

sich sonst anstecken könnten.

Wischen Sie den Kompressor mit einem feuchten Tuch mit einem milden

Reinigungsmittel ab und halten Sie ihn frei von Staub. Wenn Sie ein

anderes Reinigungsmittel verwenden, wählen Sie eines, das keine

chemischen Auswirkungen auf die Oberfläche des Plastikgehäuses des

Kompressors hat.

ACHTUNG - Tauchen Sie den Kompressor nicht in Flüssigkeit und

schützen Sie ihn vor Feuchtigkeit.

Wischen Sie die Matratze mit einem feuchten Tuch mit lauwarmem

Wasser und einem milden Reinigungsmittel ab. Der Überzug kann

ebenfalls gewaschen werden, nämlich mit in Wasser aufgelöstem

Natriumhypochlorit. Alle Teile müssen vor ihrer Verwendung vollständig

an der Luft trocknen.

ACHTUNG- Verwenden Sie keine Produkte, die auf Alkohol /

Phenolkomponenten basieren.

ACHTUNG- Lassen Sie die Matratze nach der Reinigung an der

Luft trocknen, ohne sie jedoch zu lange direktem

Sonnenlicht auszusetzen.

6. LAGERUNG

Für Matratze mit Luftzellen:

1. Um die Matratze zu lagern, breiten Sie sie der Länge nach und

mit der Oberseite nach unten aus.

2. Rollen Sie sie vom Kopfteil bis zum anderen Ende der Matratze

mit geöffnetem CPR-Ventil ein.

3. Umwickeln Sie die Matratze nach dem Einrollen mit dem, der

sich am unteren Ende befindet, um ein Entrollen zu vermeiden.

4. Falten Sie das Kissen in der ursprünglichen Methode.

7. INSTANDHALTUNG

1. Allgemein: Versichern Sie sich, dass sich das Kabel und der

Stecker in gutem Zustand befinden.

2. Überprüfen Sie den Zustand des Überzugs. Versichern Sie sich,

dass der Überzug zusammen mit den Schläuchen korrekt

gelagert ist.

3. Überprüfen Sie den Luftstrom der Steckverbindungen. Im

Modus "alternierende Funktion" muss der Luftstrom zwischen

den beiden Verbindungen alternieren.

4. Versichern Sie sich, dass die Luftauslässe nicht defekt oder

beschädigt sind. Um sie auszutauschen, wenden Sie sich bitte

an den Fachhändler, bei dem Sie das System erworben haben.

Fran

ais

Deutsch

13 14 15 16 476006-0000 V1.0

1. INTRODUZIONE

Questo manuale deve essere usato per l'installazione iniziale e quale

riferimento successivo.

2. DESCRIZIONE DEL PRODOTTO

2.1 COMPRESSORE

Parte frontale

1. Interruttore

2. Pannello frontale

Parte posteriore

3. Uscita dell'aria

4. Ganci

5. Cavo elettrico

2.2 Pannello frontale

1. Regolatore di pressione

Serve a controllare l'uscita di pressione

dell'aria. Se si gira in senso orario,

aumenta la pressione. Se invece si gira

in senso antiorario, diminuisce la

pressione.

2. Interruttore principale

Per accendere/ spegnere il compressore.

3. INSTALLAZIONE

Disimballare il dispositivo per verificare che non abbia subito alcun

danno durante la spedizione. Se si riscontra qualche danno,

contattare immediatamente il rivenditore.

Sistemare il materassino d'aria sul letto.

Fissare il materassino al letto con le cinghie

di nylon, se presenti.

NOTA: DOMUS 2 est un surmatelas, il doit y

avoir une mousse ou un matelas en dessous lors

de l'utilisation.

Sluit de luchtslangen van de luchtmatras aan

op de pompeenheid. Appendere il

compressore alla sponda o ai piedi del letto,

oppure posizionarlo su una superficie

livellata.

Collegare l'uscita/entrata dell'aria del

materassino al compressore.

NOTA: accertarsi che i tubi dell'aria non

siano rimasti nascosti o piegati sotto il materassino.

Collegare la spina alla presa di corrente.

NOTA: 1. Verificare che il voltaggio dell'impianto elettrico sia adatto

per il compressore. 2. Anche la presa può servire da interruttore per

disinserire l'apparecchio.

ATTENZIONE: la pompa può essere applicata solo al materassino

consigliato dal produttore. Non usarla per alcun altro scopo. (Elemento

applicato: materassino d'aria).

Accendere l'interruttore situato sul lato destro del compressore.

Alcuni consigli per l'installazione:

Dopo l'installazione, arrotolare il cavo eventualmente rimasto libero per

evitare di inciampare. Il dispositivo deve essere sistemato in un sito

completamente accessibile all’utente o ai medici.

4. FUNZIONAMENTO

NOTA: prima dell'uso, leggere attentamente le istruzioni.

4.1 FUNZIONAMENTO GENERALE

1. Accendere l'interruttore principale che si trova su un lato del

compressore.

2. Il compressore comincia a spingere l'aria verso il materassino.

Girare il regolatore in senso orario per aumentare la pressione

(compattezza) nel materassino.

NOTA: per gonfiare il materassino è consigliabile mantenere il

regolatore di pressione al massimo per un gonfiaggio più veloce. Una

volta gonfiato il materassino, l'utente può regolarne la compattezza.

4.2 CPR

In caso d'emergenza e di arresto respiratorio, estrarre

immediatamente la valvola CPR dal materassino. Le valvole CPR

sono situate nella parte superiore a destra del materassino. Per

sgonfiarlo più velocemente, si possono anche disinserire i tubi

dell'aria collegati al compressore, ma solo nei modelli attrezzati con

“quick connectors”.

5. PULIZIA

Prima dell'uso del dispositivo, è importante seguire la procedura di

pulizia, altrimenti il paziente e/o i medici potrebbero correre il rischio

di contrarre infezioni.

Passare sul compressore un panno inumidito con un detersivo

delicato e mantenere l'apparecchio lontano dalla polvere. Scegliere

sempre un detergente che non contenga agenti chimici in grado di

intaccare la superficie di plastica dell'involucro del compressore.

AVVERTENZA: non bagnare il compressore né immergerlo in

alcun tipo di liquido.

Passare sul materassino un panno inumidito in acqua tiepida (a non

più di 65ºC) e con un detergente delicato. Il rivestimento si può

lavare con ipoclorito di sodio diluito in acqua. Lasciare asciugare

accuratamente all'aria tutte le parti prima dell'uso.

AVVERTENZA: non usare prodotti a base di alcol / componenti

fenolici.

AVVERTENZA: lasciare asciugare il materassino all'aria dopo la

pulizia, ma non esporlo direttamente ai raggi del sole per un

periodo di tempo prolungato.

6. STOCCAGGIO

Per materassini a celle:

1. Per stoccare il materasso, stenderlo nel senso della lunghezza

e capovolto.

2. Cominciare ad arrotolare il materassino dalla testa verso i piedi.

3. Una volta arrotolato, avvolgere il materasso con la cinghia che

si trova sulla parte finale per evitare che si apra.

4. Piegare il materassino come da nuovo.

7. MANUTENZIONE

1. Accertarsi che il cavo e la spina siano in buono stato.

2. Verificare lo stato del rivestimento. Accertarsi che il rivestimento

e i tubi siano stati stoccati correttamente.

3. Verificare il flusso dell'aria nei tubi. Il flusso dell'aria deve

alternare tra i due connettori se la modalità di funzionamento è

alternato.

4. Accertarsi che le uscite dell'aria non siano rotte o danneggiate.

Per la sostituzione, rivolgersi al rivenditore del dispositivo.

1. INLEIDING

Deze handleiding moet worden gebruikt voor de eerste instelling van

het systeem en ter referentie.

2. PRODUCTBESCHRIJVING

2.1 POMPEENHEID

Vooraanzicht

1. Stroomschakelaar

2. Voorpaneel

Achterzijde

3. Aansluiting voor luchtslang

4. Hanger

5. Stroomkabel

2.2 Voorpaneel

1. Drukregelknop

Druk op de regelknop om de uitgaande

druk te regelen. Raadpleeg uw arts

betreffende de geschikte instelling

Hoofdschakelaar

Om de pompeenheid aan en uit

te schakelen

3. INSTALLATIE

Pak het apparaat uit en controleer of alles volledig is. Neem bij

beschadiging direct contact op met uw verdeler of met Apex Medical

Corp.

1. Plaats de DOMUS 2 bovenop een

schuim of matras bed. Maak de matras

stevig vast door de iemen aan het

bedframe te bevestigen als dat

mogelijk is.

OPGELET: DOMUS 2 is een

matrasoplegsystemen en een schuim

of matras moet onder bij het gebruik.

2. Hang de pomp aan het voeteneinde

en regel de hangers dusdanig dat de

pomp rechtop hangt, of plaats de

pomp op een plat oppervlak.

3. Sluit de luchtslangen van de

luchtmatras aan op de pompeenheid.

OPGELET: Controleer of de luchtslangen niet verdraaid of

gekneld zitten onder de matras.

4. Steek de stekker in een stopcontract.

OPGELET: 1. Controleer of de pompeenheid geschikt is

voor het plaatselijke spanningsnet.

WAARSCHUWING:

De pomp mag alleen worden gebruikt

met de matras die door de fabrikant wordt aangeraden. Gebruik

ze niet voor enig ander doel.

5. Draai de stroomschakelaar aan de rechterkant van de pomp op

de stand ON (aan).

Hieronder vindt u enkele installatietips:

Na de installatie moet de eventuele overtollige kabellengte netjes

opgeborgen worden zodat niemand erover kan vallen. Het APPARAAT

moet correct worden aangebracht op een plaats waar de

gebruikers/artsen er gemakkelijk bij kunnen.

4. WERKING

OPGELET: Lees de gebruiksaanwijzing aandachtig door voor het

gebruik.

4.1 ALGEMENE WERKING

1. Zet de stroomschakelaar aan de zijkant van de pomp aan.

2. Regel de druk volgens het comfortniveau van de patiënt door de

knop voor de drukregeling near rechts te draaien voor meer

stevigheid.

OPGELET: Telkens wanneer u de matras wilt oppompen voor

ebruik, is het raadzaam de matras eerst tot de maximumstand op

e pompen. De gebruiker / verpleger kan het drukniveau in de

atras vervolgens naar wens regelen.

4.2 Noodwerking operation

A ls er een nood-CRP op een patiënt moet worden uitgevoerd, trek

de snelkoppeling van de CPR-tag aan het hoofdeinde van de matras

aan de rechterkant dan snel los als die aanwezig is. De

snelkoppelaar van de pompeenheid kan ook worden afgekoppeld om

het aflaten van de lucht te bespoedigen. Sluit de snelkoppelaar terug

aan op de pompeenheid als de stroomvoorziening hersteld is.

5. REINIGING

Het is belangrijk om de reinigingsprocedures te volgen voordat u het

apparaat gebruikt voor patiënten, anders kunnen de patiënten en/of

dokters mogelijk geïnfecteerd geraken.

OPGELET:

De pomp niet onderdompelen in vloeistoffen.

Wrijf de pompeenheid schoon met een doek die in lauw water met

een zacht detergent werd gedrenkt (temperatuur mag niet hoger zijn

dan 65 ℃ ), of met in water opgelost reinigingsmiddel product

gevolgd door een goedgekeurd ontsmettingsmiddel. Na de reiniging

moeten alle delen aan de lucht drogen voor het gebruik.

OPGELET: Gebruik voor de reiniging geen producten op

fenolbasis.

OPGELET: Laat de matras na de reiniging aan de lucht drogen,

zonder ze te lang aan rechtstreeks zonlicht bloot te

stellen.

Vermijd stof en vermijd stoffige omgevingen. De hoes mag gereinigd

worden met in water verdund natriumhypochloriet. Alle bestanddelen

moeten aan de lucht worden gedroogd voor hun gebruik.

6. BEWARING

1. Leg het bubble pad of de matras op een vlak oppervlak

onderste boven.

2. Rol de matras op van het hoofdeinde naar het voeteneinde toe

op.

3. De riem van het voeteinde kan rond de opgerolde pad/matras

worden geslagen om te vermijden dat de matras terug afrolt.

NOTA : de matras niet vouwen, kreukelen of stapelen.

7. ONDERHOUD

1. Controleer het stroomsnoer en de stroomstekker op

beschadiging of overdreven slijtage.

2. Controleer de matrashoes op tekenen van slijtage of

beschadiging. Controleer of de matrashoes en de slangen

correct opgeborgen zitten.

3. Controleer de luchtstroom uit de luchtslang. De luchtstroom

moet iedere halve cyclustijd tussen iedere aansluiting

alterneren.

4. Controleer of de luchtslangen niet geknikt zitten of gebarsten

gebroken zijn. Voor meer informatie kunt u de lokale

vertegenwoordiger of Apex Medical Corp. contacteren.

Italiano

Nederlandse

Apex Digital Domus 2 Istruzioni per l'uso

Marca: Apex Digital

Modello: Domus 2

Tipo: Istruzioni per l'uso

Scarica il pdf

rapporto

in altre lingue

English: Apex Digital Domus 2 Operating instructions
français: Apex Digital Domus 2 Mode d'emploi
español: Apex Digital Domus 2 Instrucciones de operación
Deutsch: Apex Digital Domus 2 Bedienungsanleitung
Nederlands: Apex Digital Domus 2 Handleiding
português: Apex Digital Domus 2 Instruções de operação

Apex Digital Domus 2 Istruzioni per l'uso

Apex Digital Domus 2 Istruzioni per l'uso

in altre lingue

Documenti correlati

Altri documenti