Transcend 3 miniCPAP Guida utente



Quick Guide



Transcend 3 miniCPAP Quick Guide Page 2

Table of Contents

ENGLISH

.....................................3

FRANÇAIS

...................................

17

DEUTSCH

....................................

31

ITALIANO

....................................

46

ESPAÑOL

....................................

59

NEDERLANDS

....................................

73

Transcend 3 miniCPAP Quick Guide Page 3

Introduction

Thank you for choosing Transcend, the leading innovator in portable CPAP therapy. The

Transcend 3 miniCPAP provides positive airway pressure to users in the range of 4 to

20 cmH2O as prescribed by the clinician. The Transcend 3 miniCPAP product family

includes the Transcend 3 miniCPAP and the Transcend 3 miniCPAP Auto. Buttons and LED

lights facilitate control and provide operational feedback. A DC power jack and a USB port

are also incorporated into the Transcend 3 miniCPAP.

NOTE: For more detailed descriptions, warnings, cautions and troubleshooting

procedures refer to the Transcend 3 miniCPAP User Manual that is available for

download at www.MyTranscend.com/support or by calling Somnetics customer

service at 877-621-9626 or [email protected] to request a copy.

Warnings

 Do not allow water to enter this device. Transcend 3 miniCPAP should not be

exposed to environmental conditions where the system may get wet.

 This device is not intended for life support.

 The Transcend 3 miniCPAP must be set up and adjusted by a trained provider

before being used for therapy ramp and pressure.

 The air temperature produced by this device can be as much as 10ºF higher than

the temperature of the room. Exercise caution if the room temperature is warmer

than 90ºF (32ºC).

 Do not block or otherwise obstruct the exhalation ports of the mask. Follow the

manufacturer’s instructions included with your mask.

 This equipment is not suitable for use with oxygen or in the presence of a

flammable anesthetic mixture with air or oxygen, or with nitrous oxide. Sources of

oxygen must be located more than 1 meter from the equipment to avoid the risk of

fire and burns.

 The Transcend 3 miniCPAP is only to be used with the supplied or recommended

accessories. Use of accessories not recommended may result in increased

electromagnetic emissions or decreased electromagnetic immunity of the PAP

system and may be potentially unsafe.

 The Transcend 3 miniCPAP is not defibrillation proof.

 Do not attempt to sterilize Transcend 3 miniCPAP.

 If the device is to be used by multiple patients a main flow bacteria filter should be

installed in-line between the device and the breathing circuit tubing to prevent

contamination.

 The device should be used only with masks and connectors recommended by

Somnetics or a health care professional. A mask should not be used unless the

device is turned on and is properly delivering ramp or therapy pressure. The

exhalation port(s) associated with the mask should never be blocked. Explanation

of the Warning: The device is intended to be used with masks or connectors

specifically designed to have exhalation ports to allow continuous flow of air out of

Transcend 3 miniCPAP Quick Guide Page 4

the mask. When the device is in operation, air flow from the device flushes exhaled

air out through the mask exhalation port. When the device is not operating,

however, fresh air will not be provided through the mask and exhaled air may be

rebreathed.

 Failure to use a mask or accessory that minimizes rebreathing of carbon dioxide or

permits spontaneous breathing can cause asphyxiation.

 Do not position the equipment in bed. Covering breathing tubes with a blanket or

heating them can affect the quality of therapy or injure the user.

 To prevent disconnection of the tubing during use, only tubes in compliance with

ISO 5367 or ISO 80601-2-74 should be used.

 Strangulation hazard from power cord and air tube. These can become wrapped

around a neck and STRANGLE. Keep power cord and air tube more than 3 feet from

a baby’s crib and out of baby’s reach. Keep cord and tube out of children’s reach.

 Small parts are unlikely to be expelled from the Transcend 3 miniCPAP enclosure,

but in case of severe damage internal components may fragment and create a

swallowing or choking hazard if they get out of the enclosure.

Cautions

 Federal law (United States) restricts this device to sale by, or on the order of, a

physician.

 Power the Transcend 3 miniCPAP only with the Somnetics-supplied power supplies,

mobile power adapter, or batteries.

 Discontinue use of the Transcend 3 miniCPAP and contact your physician if

respiratory or skin irritations occur.

 Do not introduce objects into the Transcend 3 miniCPAP air inlet or air outlet.

 Inspect the power supply for signs of wear or damage before each use. Replace the

power cord if necessary.

 Somnetics recommends replacing the air delivery tubing (hose) after every three

months of use.

 To protect the environment, some parts and accessories of the Transcend 3

miniCPAP, including optional batteries, must be disposed of in accordance with local

regulations.

 The equipment must not be covered or positioned in such a way that adversely

affects the performance of the equipment, as it may also create a safety issue.

Examples of this would include:

 The equipment must not be positioned in a bed.

 The equipment should not be placed anywhere other than on a firm,

flat surface.

 Do not position in a location where pets or children can access

equipment.

 Do not position near an open window or other location where dust, or

pests (insects) can affect equipment safety and/or performance.

 Do not position next to a curtain that blocks the flow of cooling

air, thereby causing the equipment to overheat.

 Do not block the air intake port, thereby interfering with therapy.

Transcend 3 miniCPAP Quick Guide Page 5

DBP

Device contains DBP (a phthalate). Significant exposure to DBP may

interfere with the normal development of the male reproductive tract.

Testing has demonstrated that DBP exposure levels are well below

established limits. Women who are pregnant or nursing may wish to

discuss the benefits and risks of this device with a physician.

Components of the Transcend 3 miniCPAP

Begin by unpacking all items from the Transcend 3 miniCPAP Auto travel bag and

inspecting them to ensure they were not damaged during shipment. Report any missing

or damaged items to the home healthcare provider that sold the Transcend 3 miniCPAP

Auto to you.

Included with Transcend 3 miniCPAP

 Transcend Travel bag

 Air Supply Tube (Compatible with standard 22 mm connector)

 Transcend 3 miniCPAP Auto or Transcend 3 miniCPAP

 Transcend 3 miniCPAP Quick Guide

 Changeable plug pack

 Multi-plug universal power supply (PSA2)

 USB Cable

Transcend 3 miniCPAP Quick Guide Page 6

Accessories (Sold Separately)

 Transcend Mobile Power Adapter

 Transcend P4 Battery

 Transcend P8 Battery

 Transcend Portable Solar Battery Charger (to be used as an alternative charging

source for Transcend P4 and P8 batteries)

 Bluetooth Module

 Patient Mask

Assembling the Transcend 3 miniCPAP Device

1. Attach the air supply tube to the air outlet on the Transcend 3 miniCPAP device.

2. Connect the mask to the opposite end of the air supply tube.

3. Plug the power supply barrel connector into the Transcend 3 miniCPAP power jack

on the rear of the device.

4. Connect power supply to a wall outlet.

Using the Multi-Plug Universal Power Supply

(PSA2)

The Multi-plug Universal Power Supply (PSA2) and Changeable Plug Pack containing three

(3) exchangeable plugs are contained with each Transcend 3 miniCPAP. The changeable

plug packs are suitable for use in most countries around the world.

1. Determine which plug is required to power the device based upon the outlet

style.

2. If the correct plug is not already attached to the Power Supply remove the

attached plug by depressing the button on the detachable plug and turning the

plug in a counterclockwise motion until it releases from the power supply.

3. Attach the desired plug by lining up the protruding tabs on the back of the plug

with the gaps on the Power Supply and gently pushing the plug into the slot.

Turn the plug clockwise until it clicks into place. You should hear an audible

click.

Transcend 3 miniCPAP Quick Guide Page 7

4. Insert the barrel connector of power supply into power jack on the back of the

Transcend 3 miniCPAP device.

5. Insert the other end of the power supply into an AC line power outlet.

6. The Transcend 3 miniCPAP power-up LED flash sequence should initiate. Once

the power-up LED flash sequence is complete the LED lights will turn off. This

sequence indicates that power is being supplied to the Transcend 3 miniCPAP

and that it has successfully entered Standby Mode.

NOTE: Use only the Somnetics-supplied Universal Power Supplies. Do not use a

power converter or voltage transformer with the PSA2 Universal Power Supply.

NOTE: Make certain that the plug attachment is fully secured to the Power

Supply before inserting the power supply into the wall outlet.

Transcend 3 miniCPAP Device

The Transcend 3 miniCPAP comes ready to generate and regulate continuous positive

airway pressure therapy for delivery to the interface (mask). An external power source

connects to the Transcend 3 miniCPAP to supply power to the device.

Control Panel

The Transcend 3 miniCPAP control panel has two pushbuttons used to activate the blower

and reactivate the pressure ramp feature. There are also two LED lights, including a green

LED for indicating normal operational modes and a yellow LED that indicates fault

conditions.

Reattach: Insert

plug and turn

Remove

Plug

Remove:

Depress button

and turn

Transcend 3 miniCPAP Quick Guide Page 8

Power Connection Jack and USB Port

Power Jack

The power jack accepts the barrel plug of the output cable from a DC power source to

operate the Transcend 3 miniCPAP.

A variety of power sources may be used to power the Transcend 3 miniCPAP. An AC to DC

converting power supply is provided with your device and should be used when powering

the device by line (wall outlet) power.

An optional mobile power adapter connects to a DC power outlet, such as that found in an

Automobile, truck, RV, boat, or similar vehicle.

Optional Transcend battery packs are also available to power the Transcend 3 miniCPAP.

USB port

A mini-AB USB port is provided for direct data exchange between the Transcend 3

miniCPAP and a computer via a USB data cable. This interface allows the clinician to

configure the Transcend 3 miniCPAP for prescription pressure, ramp settings and Auto

settings and provides access to therapy compliance information that can be viewed by the

user and emailed to the clinician.

Power button

Green LED

Yellow LED

Ramp button

Transcend 3 miniCPAP Quick Guide Page 9

NOTE: It may be necessary to unplug the cables and reconnect to ensure a good

connection.

Using the Transcend 3 miniCPAP

The control panel of the Transcend 3 miniCPAP has two pushbuttons that activate the

blower and reactivate the pressure ramp feature. There are also two LED lights, including

a green LED for indicating normal operational modes and a yellow LED for indicating fault

conditions. The Transcend 3 miniCPAP operational status is displayed by LED illumination

states.

When a power source is connected to the device the Transcend 3 miniCPAP power-up LED

flash sequence should initiate. Once the power-up LED flash sequence is complete the

LED lights will turn off. This sequence indicates that power is being supplied to the

Transcend 3 miniCPAP and that it has successfully entered Standby Mode. During therapy

delivery, the LED lights remain off to avoid disturbing the patient and/or bed partner.

NOTE: If the Transcend 3 miniCPAP loses power while delivering therapy, it will

resume delivering therapy as soon as power is restored. The device will repeat

the power-up LED flash sequence prior to the blower restarting.

Standard User Modes

Normal operation consists of four modes:

Off When the device is not connected to a power source the device is off. Control

panel LEDs are both off.

USB port

Power jack

Transcend 3 miniCPAP Quick Guide Page 10

StandbyWhen power is applied to the device it completes the power-up LED sequence and

enters Standby Mode. Standby Mode is also initiated by pressing the power button

when the device is in On Mode or if the mask is removed while in On Mode. As

long as power is supplied to the device it will remain in Standby Mode until On or

Drying Mode is initiated.

On When in On Mode the blower is working and regulated device therapy pressure is

being generated. The LED lights remain off. On Mode is initiated by pressing the

power button when the device is in Standby Mode and the mask is worn by the

patient.

Drying To initiate Drying Mode depress the Ramp button and press the Power button

simultaneously. When in Drying Mode the blower runs at a low speed for 30

minutes. During Drying Mode the LED lights remain off and blower pressure is not

regulated to provide therapy.

Starting Therapy

 Connect the Transcend 3 miniCPAP to a power source and allow it to enter Standby

Mode.

 Be sure your user interface is fit firmly in place before initiating therapy.

 To initiate therapy, press the Power button. Pressing the Power button when

Transcend 3 miniCPAP is in Standby Mode will initiate On Mode. Air flow will begin

as the blower delivers or ramps to prescribed therapy pressure.

Using the Ramp Function

The Ramp feature lets users acclimate to air flow by starting at a lower pressure and

gradually increasing to the prescribed pressure setting as the user falls asleep. The

software section of this manual displays how to modify ramp settings on your device.

To accelerate the rate of the pressure increase during Ramp, hold the Ramp button down

until the device reaches a comfortable therapy pressure. When the Ramp button is

released the device will continue in Ramp Mode until it reaches the prescribed therapy

pressure.

 Be sure the Transcend 3 miniCPAP is in On Mode. If not, press the power button.

o If Ramp is configured, it will begin automatically.

 Adjust your mask to eliminate mask leaks.

 To reactivate Ramp after reaching the prescribed therapy pressure, press the Ramp

button. The pressure will drop to the Ramp starting pressure and will gradually

increase over a preset length of time until reaching the prescribed therapy pressure

NOTE: Momentarily pressing the Ramp Button during ramped pressure delivery

will not affect the pressure delivered. To end Ramp early, hold down the Ramp

button until the pressure reaches the prescribed level. If Ramp is no longer

desired, disable it via software.

Transcend 3 miniCPAP Quick Guide Page 11

NOTE: In the event of power loss during ramp, the Transcend 3 miniCPAP will

resume ramp from the last delivered pressure as soon as power is restored.

Using the EZEX Function

The EZEX function is a special feature that decreases therapy pressure on exhalation. This

feature is designed to provide additional comfort to the patient by reducing the amount of

resistance they experience as they exhale.

There are four EZEX settings: OFF, 1, 2 or 3; progressively increasing the amount of

pressure relief from none to maximum. The software section of the user manual displays

how to modify EZEX settings.

NOTE: To download the Transcend 3 miniCPAP user manual visit

https://MyTranscend.com/customer-care/user-guides or call Somnetics

customer service at 877-621-9626 to request a copy.

Ending Therapy

To end the delivery of therapy while the blower is on, press the Power button to

deactivate the blower and return the device to Standby Mode. It is recommended the user

initiate the Drying Mode function after each therapy session to dry the device interior.

Drying Mode

At the end of each therapy session it is recommended the user initiates the Drying Mode.

To initiate Drying Mode depress the Ramp button and press the Power button

simultaneously. When in Drying Mode the blower runs at a low speed for 30 minutes.

During Drying Mode the LED lights remain off and blower pressure is not regulated to

provide therapy. Using the Drying Mode flushes air through the system to remove traces

of moisture from the interior of the device and airway circuit. After the 30-minute drying

cycle, the blower will turn off and the device will automatically enter Standby Mode.

Transcend 3 miniCPAP Quick Guide Page 12

Replacing the Filter Media

The Transcend 3 miniCPAP Filter Media should be replaced every six months at minimum.

Transcend Desktop Software

The free Transcend Desktop Software can be downloaded at

www.MyTranscend.com/support. The Transcend software allow you to view detailed

compliance data and adjust the comfort features on your device.

TranSync

The TranSync Compliance Monitoring System is designed to provide patients with a secure

and convenient way to view compliance data and transmit it to homecare providers and

clinicians via the secure, cloud-based TranSync website (www.MyTranSync.com). Data

can be uploaded to the TranSync website with the use of either the Transcend Desktop

Software or the TranSync Bluetooth Module and mobile app.

Users must enter the email address associated with their TranSync account. If you don’t

already have a TranSync account, or have a profile set up by your homecare provider,

visit www.MyTransync.com/Registration to set up your individual account before you

attempt to transfer compliance information.

Pull tab to release

filter assembly

Transcend 3 miniCPAP Quick Guide Page 13

TranSync Mobile App

The TranSync mobile app (available for IOS and Android) can be downloaded from the

Apple

®

andGoogle

®

app stores. The appuser guides can be downloaded at

www.MyTranscend.com/support. The app can be used to view compliance data uploaded

to the TranSync cloud database (www.MyTranSync.com) via the desktop software or the

TranSync Bluetooth Module.

TranSync Bluetooth Module

To use your Bluetooth Module, insert with logo facing up.

To download the TranSync Mobile App or the TranSync Mobile App User Guide go to

https://MyTranscend.com/support.

TranSync Mobile System Compatibility

iOS Version 11.1 or later

Android Version 5.0 (API level 21) or later

Regulatory FCC Part 15 Compliant

Transcend 3 miniCPAP Quick Guide Page 14

Caring for your Transcend 3 miniCPAP and its

Components

Warning:

 Unplug the Transcend 3 miniCPAP before cleaning.

 Do not submerge the Transcend 3 miniCPAP or power supply in liquid.

 Prevent water from entering any openings of the device.

 Do not use harsh or abrasive cleaning agents to clean the device or any

components.

Remove the filter assembly by pulling the tab on the back of the device to release it. Then

pull the filter assembly away from the device. Discard the entire filter assembly and

replace with a new one.

Do not attempt to sterilize the Transcend 3 miniCPAP.

Do not place cleaning materials, such as a cloth or liquid, into the device air inlet or air

outlet connector.

Cleaning the Exterior

Follow these instructions to clean the exterior of the Transcend 3 miniCPAP.

1. Unplug the power supply prior to cleaning and disconnect the device from power

cords.

2. Mix a solution of 5% mild liquid detergent in distilled water (1.6 fl oz liquid

detergent per quart of distilled water). Mild detergent should contain biodegradable

anionic surfactants and no phosphate.

3. Submerge a lint-free cotton cloth into the detergent solution.

4. Wring excess water from the cloth then wipe the exterior of the Transcend 3

miniCPAP device for approximately 20 seconds using a gentle, back and forth

wiping motion from the front to back of the device. Apply firm pressure and ensure

contact with all accessible contact surfaces to adequately remove soil buildup.

5. Rinse the cloth in clear water to remove residual cleaning solution.

6. Wring excess water from the cloth then wipe the Transcend 3 miniCPAP using a

gentle front to back wiping motion to remove any detergent solution remaining on

its surface.

7. Wipe the device with a dry, lint-free cotton cloth until the device is fully dry.

Transcend 3 miniCPAP Quick Guide Page 15

Cleaning of Accessories

The following accessory should be cleaned with a 5% solution of mild liquid detergent in

distilled water (1.6 fl oz liquid cleaning detergent per quart of distilled water). Mild

detergent should contain biodegradable anionic surfactants and no phosphate. Follow

these steps to clean the accessories.

Accessory Periodic Cleaning Cycle Product Service Life

Air Supply Tube Daily 3-Year

1. Fully immerse the air supply tube in the cleaning solution.

2. While immersed, thoroughly wipe the surface with a lint-free cotton cloth. Apply

firm pressure and ensure contact with all accessible contact surfaces to adequately

remove soil buildup.

3. Clean the inside of the air supply tube by lifting, then lowering the ends of the tube

while the tube is filled with cleaning solution.

4. Rinse air supply tube by immersing in distilled water. Move the air supply tube in a

back and forth motion for approximately10 seconds to remove cleaning agent

residue.

5. Rinse the air supply tube in distilled water by fully immersing. Lift, then lower, the

ends of the tube while the tube is filled with water. Repeat this motion for

approximately 10 seconds to remove cleaning agent residue.

6. Dry the outside of the air supply tube with a dry, lint-free cotton cloth. Allow the

tube to air dry until the inside of the tube is dry. Length of drying time will depend

on ambient conditions.

Questions? Contact Somnetics customer service 877-621-9626 or

[email protected].

Transcend 3 miniCPAP Quick Guide Page 16

Disposable Parts

Item Part

number

Item Part

number

Transcend 3 Filter Assembly 503109 Standard 6-foot hose 503081

Accessories

Item Part

number

Item Part

number

Transcend P8 Battery 503023 Transcend Mobile Power

Adapter (MPA1)

503029

Transcend P4 Battery 503026 Transcend Portable Solar

Battery Charger

503056

Transcend 3 Bluetooth Module 503084

Replacement Parts

Item Part

number

Item Part

number

Transcend 3 miniCPAP Auto 503104 Transcend Travel Bag 503012

Transcend 3 miniCPAP Auto

Service Unit 503105

Multi-plug Universal Power

Supply (PSA2) 503059

Transcend 3 miniCPAP 503106 Changeable Plug Pack 503060

Transcend 3 miniCPAP Service

Unit 503107

USB cable 503020

Multi-plug Universal Power

Supply

Set

(Contains 503059 & 503060) 503078

Beknopte handleiding Transcend 3 miniCPAP Pagina 17

Introduction

Merci d'avoir choisi Transcend., chef de file de l’innovation en matière de systèmes

de traitement CPAP portables. Le système Transcend 3 miniCPAP fournit une pression

positive aux utilisateurs dans une plage de 4 à 20 cm H2O, telle que prescrite par le

médecin. La gamme de produits Transcend 3 miniCPAP inclut le Transcend 3 miniCPAP

et le Transcend 3 miniCPAP Auto. Les boutons et les voyants lumineux facilitent le

contrôle et fournissent un feedback opérationnel. Une prise d’alimentation en courant

continu et un port USB sont également inclus dans l’appareil Transcend 3 miniCPAP.

Remarque : Pour obtenir une description plus détaillée de l’appareil, des

avertissements, ainsi que des procédures de dépannage, consultez le manuel

utilisateur du système Transcend 3 miniCPAP, téléchargeable à l’adresse

suivante : www.MyTranscend.com/support. Vous pouvez également contacter

le service client Somnetics au 877-621-9626 ou via l’e-mail [email protected]

pour en demander un exemplaire.

Avertissements

 Empêchez l’eau de pénétrer dans l’appareil. L’appareil Transcend 3 miniCPAP

ne doit pas être conservé dans un environnement humide.

 Cet appareil n’a pas pour but de maintenir la vie.

 Le système Transcend 3 miniCPAP doit être configuré et ajusté par un professionnel

de la santé formé avant d’être utilisé pour la phase d’augmentation et la pression

de traitement.

 La température de l’air produit par l’appareil peut être supérieure d’environ -12 °C

à celle de la pièce. Soyez vigilant si la température de la pièce dépasse 32 °C.

 Ne bloquez pas et n’obstruez pas les orifices d’expiration du masque. Respectez

les instructions du fabricant incluses avec le masque.

 Cet équipement n’est pas compatible avec l’utilisation d’oxygène. De même,

ne l’utilisez pas en présence d’un mélange anesthésique inflammable d’air ou

d’oxygène ou avec du protoxyde d’azote. Les sources d'oxygène doivent être

situées à plus de 1 mètre de l'équipement, afin d'éviter tout risque d'incendie

et de brûlure.

 Le système Transcend 3 miniCPAP doit uniquement être utilisé avec les accessoires

fournis et recommandés. L’utilisation d’accessoires non recommandés peut

provoquer une augmentation des émissions électromagnétiques ou une diminution

de l’immunité électromagnétique du système de PAP et peut être potentiellement

dangereuse.

 Le système Transcend 3 miniCPAP n’est pas anti-défibrillateur.

 Ne tentez pas de stériliser l’appareil Transcend 3 miniCPAP.

 Si l’appareil est utilisé par plusieurs patients, un filtre antibactérien stoppant le flux

principal des bactéries doit être installé entre l’appareil et le tuyau du circuit

respiratoire afin d’empêcher toute contamination.

Beknopte handleiding Transcend 3 miniCPAP Pagina 18

 L’appareil doit être utilisé uniquement avec des masques et des connecteurs

recommandés par Somnetics ou par un professionnel de la santé. Utilisez le

masque uniquement lorsque l’appareil est sous tension et délivre la phase

d’augmentation ou la pression de traitement. Les orifices d’expiration reliés

au masque ne doivent jamais être bloqués. Explication de cet avertissement :

l’appareil est conçu pour fonctionner avec des masques et des connecteurs

spéciaux dotés d’orifices d’expiration permettant à l’air de sortir continuellement

du masque. Lorsque l’appareil est en fonctionnement, l’air frais de l’appareil chasse

l’air expiré, via les orifices d’expiration du masque. Cependant, lorsque l’appareil

est hors tension, il n’y a pas assez d’air frais apporté dans le masque et il est

possible que de l’air expiré soit de nouveau inhalé.

 Le fait de ne pas utiliser un masque ou un accessoire qui réduit au minimum

la réinspiration de dioxyde de carbone ou qui permet une respiration

spontanée peut entraîner une asphyxie.

 Ne placez pas l'équipement dans le lit. Le fait de recouvrir les tuyaux respiratoires

d'une couverture ou de les chauffer peut affecter la qualité du traitement ou blesser

l'utilisateur.

 Pour éviter le débranchement du tuyau pendant l'utilisation, seuls des tuyaux

conformes à la norme ISO 5367 ou ISO 80601-2-74 doivent être utilisés.

 Risque de strangulation avec le cordon d'alimentation et le tuyau d'air. Ces

deux éléments peuvent s'entourer autour du cou et ÉTRANGLER. Tenez le

cordon d'alimentation et le tuyau d'air à plus d'un mètre du berceau et hors

de portée d'un bébé. Tenez le cordon et le tuyau hors de portée des enfants.

 Il existe peu de risque que de petites pièces s'échappent du boîtier du

Transcend 3 miniCPAP ; cependant, en cas de dommage important, des

composants internes peuvent se briser et représenter un risque d'étouffement

en cas d'ingestion s'ils sortent du boîtier.

Mises en garde

 Selon la loi fédérale américaine, cet appareil ne peut être vendu que par un

médecin ou sur ordonnance d’un médecin.

 Branchez le système Transcend 3 miniCPAP uniquement avec l’alimentation,

l’adaptateur mobile ou les batteries fournis par Somnetics.

 En cas d’irritation des voies respiratoires ou d’irritations cutanées, cessez

d’utiliser l’appareil Transcend 3 miniCPAP et contactez votre médecin.

 N’introduisez pas d’objets dans les systèmes d’entrée ou de sortie d’air de

l’appareil Transcend 3 miniCPAP.

 Avant chaque utilisation, vérifiez que l’alimentation ne présente pas de signes

d’usure ou de détérioration. Si nécessaire, remplacez le cordon d’alimentation.

 Somnectics recommande de remplacer le tuyau (flexible) d’alimentation en air

après trois mois d’utilisation.

 Par souci environnemental, certains éléments et accessoires du système

Transcend 3 miniCPAP, dont les batteries optionnelles, doivent être mis au rebut

conformément aux réglementations locales en vigueur.

 L'équipement ne doit pas être recouvert ou positionné de telle sorte que

le fonctionnement ou les performances de l'équipement soient affectés

négativement, car cela risque de provoquer également un problème de sécurité.

Beknopte handleiding Transcend 3 miniCPAP Pagina 19

En voici des exemples :

 L'équipement ne doit pas être placé dans un lit.

 L'équipement ne doit pas être placé ailleurs que sur une surface

stable et plane.

 Ne placez pas l'appareil dans un endroit dans lequel les animaux

domestiques ou les enfants peuvent accéder à l'équipement.

 Ne le placez pas vers une fenêtre ouverte ou à tout autre endroit

où la poussière ou les parasites nuisibles (insectes) peuvent

affecter la sécurité et/ou les performances de l'équipement.

 Ne placez pas l'appareil à côté d'un rideau (qui bloque le flux d'air

de refroidissement, ce qui entraîne une surchauffe de l'équipement).

 N'obstruez pas l'orifice d'admission d'air, pour ne pas interférer avec

le traitement.

DBP

L'appareil contient du DBP (un phtalate). Une exposition importante

au DBP peut interférer avec le développement normal de l'appareil

reproducteur masculin. Les essais ont démontré que les niveaux

d'exposition au DBP sont bien inférieurs aux limites établies. Les femmes

enceintes ou qui allaitent peuvent discuter des avantages et des risques

de cet appareil avec un médecin.

Composants du Transcend 3 miniCPAP

À la réception du système 3 miniCPAP Auto, sortez tous les éléments de l’emballage et

vérifiez qu’ils n’ont pas été endommagés pendant le transport. Signalez les dommages

ou éléments manquants au fournisseur santé qui vous a procuré l’appareil Transcend 3

miniCPAP Auto.

Beknopte handleiding Transcend 3 miniCPAP Pagina 20

Inclus dans le Transcend 3 miniCPAP

 Sac de transport Transcend

 Tube d'alimentation en air (compatible avec le connecteur standard 22 mm)

 Transcend 3 miniCPAP Auto ou Transcend 3 miniCPAP

 Guide rapide du Transcend 3 miniCPAP

 Lot de fiches interchangeables

 Alimentation universelle multiprise (PSA2)

 Câble USB

Accessoires (vendus séparément)

 Adaptateur électrique mobile Transcend

 Batterie P4 Transcend

 Batterie P8 Transcend

 Transcend Portable Solar Charger (à utiliser comme source de chargement

alternative pour les batteries Transcend P4 et P8)

 Module Bluetooth

 Masque patient

Assemblage du système Transcend 3 miniCPAP

1. Fixez le tuyau d'alimentation d'air sur la sortie d'air de l'appareil

Transcend 3 miniCPAP.

2. Branchez le masque à l’autre extrémité du tuyau d’alimentation en air.

3. Branchez le connecteur cylindrique de l’alimentation dans la prise d'alimentation

du Transcend 3 miniCPAP, située à l'arrière de l'appareil.

4. Branchez l’alimentation à une prise murale.

La pagina sta caricando ...

Transcend 3 miniCPAP Guida utente

Transcend 3 miniCPAP Guida utente

in altre lingue

Altri documenti